Products (44,000+)

TUSB212RWBR - USB 2.0 HS Signal Conditioner | Texas Instruments
TUSB212RWBR

TUSB212RWBR - USB 2.0 HS Signal Conditioner | Texas Instruments

Texas Instruments TUSB212RWBR is a USB 2.0 High-Speed signal conditioner with DC boost, packaged in a 12-X2QFN surface-mount package measuring 1.6 mm by 1.6 mm. It is designed to compensate for intersymbol interference caused by signal loss in a transmission channel. The device applies programmable AC boost and DC boost to restore degraded high-speed data signals while remaining agnostic to USB Low-Speed and Full-Speed traffic. A USB signal conditioner is a specialized interface IC that improves an already transmitted USB differential signal without changing the protocol implemented by the USB host, hub, or peripheral. Its position in the signal path is between the transmitter and a lossy channel. This makes the TUSB212RWBR part of the broader USB interface hierarchy: USB 2.0 interface IC, signal conditioning IC, redriver, and ultimately a semiconductor-based connectivity device. The principal feature of the TUSB212RWBR is programmable signal AC boost combined with DC boost. AC boost restores high-frequency signal amplitude lost through channel attenuation, while DC boost helps maintain the differential voltage required for reliable high-speed signaling. The manufacturer describes the implementation as patent pending and identifies USB On-The-Go compatibility as an additional design feature. Low-Speed and Full-Speed signal characteristics remain unaffected by the conditioning function. TUSB212RWBR is intended for USB 2.0 systems where trace losses, connector transitions, cable segments, or routing discontinuities reduce High-Speed eye margin. Conditioning is normally applied to the D+ and D+ differential pair as a complete pair rather than to either conductor independently. The correction must be tuned from measured eye diagrams because excessive boost can increase edge distortion, jitter, or emissions instead of improving receiver recovery. Typical deployments include USB hubs, cable assemblies, peripheral boards, host adapters, test equipment, and USB-to-storage or USB-to-network interfaces. In a hub, the conditioner can be placed near an upstream port so the signal entering a long cable is restored before attenuation becomes significant. In a peripheral, it can compensate for PCB routing from a connector to a USB controller. When applying the device, preserve the USB differential impedance recommended by the manufacturer and keep the D+ and D+ routes coupled and symmetric. Decoupling and boost configuration should follow the manufacturer reference layout. Confirm compliance through eye-height, jitter, rise-time, and emissions measurements because channel length, connector geometry, and host behavior determine the useful correction amount. This product page combines the manufacturer's USB 2.0 signal-conditioning description, exact TUSB212RWBR package information, extracted distributor pricing, and practical replacement analysis. It also distinguishes confirmed drop-in candidates from unsupported package or functional substitutions so engineers can make a PCB-level decision without relying on generic USB redriver recommendations.

RFQ Contact
TUSB212RWBT - USB 2.0 HS Signal Conditioner | Texas Instruments
TUSB212RWBT

TUSB212RWBT - USB 2.0 HS Signal Conditioner | Texas Instruments

The Texas Instruments TUSB212RWBT is a USB 2.0 high-speed signal conditioner with DC boost, housed in a 12-X2QFN surface-mount package measuring 1.6 mm by 1.6 mm. It is designed to compensate for intersymbol interference in lossy USB channels while supporting Low-Speed, Full-Speed, and High-Speed signaling. The device is configurable by pin strap or I2C and supports selectable signal gain, including daisy-chain operation for high-loss applications. A USB signal conditioner is an interface IC placed within a USB data path to improve signal integrity without changing the underlying USB protocol. Its hierarchy is USB interface device, signal-processing interface IC, and interface IC. The TUSB212 specifically targets USB 2.0 channels in which connector launches, PCB traces, cables, or intervening devices have introduced bandwidth-related distortion. The conditioner supports USB 2.0, OTG 2.0, and Battery Charger 1.2 environments as identified by Texas Instruments. The principal features include programmable AC boost, programmable DC boost, pin-strap or I2C configuration, and selectable gain. According to the manufacturer product page, the device supports channels up to 5 meters before the conditioning point or 2 meters after it. It also handles D1P/M and D2P/M interchangeably, is agnostic to host or device roles, and maintains compatibility across Low-Speed, Full-Speed, and High-Speed signals. Technically, the TUSB212 applies frequency-dependent correction intended to counter channel loss and intersymbol interference. AC boost controls the high-frequency correction applied to the data waveform, while DC boost adjusts the low-frequency transition baseline. Four selectable AC boost settings are described by Texas Instruments, and the I2C or pin-strap interface allows implementation choices to suit board constraints. The design is intended to preserve Low-Speed and Full-Speed characteristics while compensating High-Speed signals. Typical applications include USB hubs, host controllers, peripheral ports, cable assemblies, docking systems, and test equipment with degraded or lossy channels. The interchangeable D1P/M and D2P/M interfaces simplify symmetrical USB routing, while the compact 12-X2QFN package supports space-constrained portable and industrial designs. The I2C configuration option also permits controlled adjustments where fixed pin straps are insufficient. Designers should place the conditioner close to the channel impairment boundary and confirm the supported pre-channel or post-channel distance. USB differential routing must preserve controlled impedance and minimize stubs, while the I2C and configuration pins require appropriate pull networks. Verify the selected boost setting with compliance masks, eye diagrams, and worst-case cable and connector combinations rather than relying on nominal channel length alone.

RFQ Contact
TUSB2136PM - 2-Port USB 2.0 Hub Controller | Texas Instruments
TUSB2136PM

TUSB2136PM - 2-Port USB 2.0 Hub Controller | Texas Instruments

Texas Instruments TUSB2136PM is a USB 2.0 two-port hub controller with an integrated general-purpose function controller, supplied in a 64-LQFP surface-mount package measuring 10 mm by 10 mm. It operates from a 3 V to 3.6 V supply and is specified for a 0 °C to 70 °C ambient operating range. The component is listed as active and is intended for USB interface and hub-controller designs. A USB hub controller is an interface integrated circuit that manages a USB host connection and coordinates attached USB devices. Within the product hierarchy, a USB 2.0 hub controller is an interface IC, a USB interface device, and a semiconductor. This TUSB2136 variant combines two-port hub control with a general-purpose function controller, allowing the hub function and device-side control logic to be consolidated within one package. The principal verified features are two USB 2.0 ports, a 3 V to 3.6 V operating-supply range, and integrated general-purpose function control. The controller is packaged in a 64-pin LQFP measuring 10 mm by 10 mm, providing a surface-mount implementation for compact USB equipment. The operating temperature range of 0 °C to 70 °C identifies it as a commercial-temperature option rather than an explicitly automotive-qualified or extended-temperature device. The TUSB2136PM combines a compound USB hub function with an embedded general-purpose 8052 MCU, as identified in the supplied datasheet result. This architecture is useful when downstream equipment needs local device handling, configuration logic, or peripheral control in addition to standard USB hub behavior. Its consolidated approach can reduce the number of discrete interface components required around a USB connection, although the complete implementation must be validated against the manufacturer datasheet and reference design. Typical uses include USB connection hubs, computer peripherals, docking equipment, and embedded USB interface products. Its two-port configuration is appropriate for systems that need to expose multiple USB connections through one upstream USB link. Integration of the general-purpose function controller is especially relevant to designs in which hub management must coexist with vendor-specific control behavior or device-specific handling. Designers should pay particular attention to USB signal routing, supply decoupling, and the exact pin assignments shown in the manufacturer documentation. Because the verified sources do not provide the complete pin table, crystal requirements, programming interface, USB transceiver details, or decoupling values, those items must be obtained from the official datasheet before schematic capture. No automotive qualification or regulatory status beyond the supplied active-status information should be inferred. This page combines the verified USB version, port count, supply range, package, temperature range, lifecycle status, and distributor availability information with practical integration guidance. It also distinguishes documented characteristics from unknown electrical details and avoids presenting unverified pinout or replacement claims as drop-in-compatible alternatives.

RFQ Contact
TUSB2140BN USB 1.1 4-Port Hub Controller | Texas Instruments
TUSB2140BN

TUSB2140BN USB 1.1 4-Port Hub Controller | Texas Instruments

The Texas Instruments TUSB2140BN is a USB 1.1 interface controller for four-port USB hub applications, supplied in a 40-pin DIP package measuring 0.600 inches, or 15.24 mm, across. The device is identified by distributors as a USB interface bus controller with integrated transceiver characteristics, and it is associated with an I2C microcontroller interface in supplier documentation. The verified product information confirms a through-hole DIP format, commercial temperature grade, and 40 terminals. It also confirms availability through multiple distributors, including 6,048 pieces reported by Heisener and a unit price of $6.4513 as of 2026-10-30. The TUSB2140BN is therefore positioned as a legacy USB hub controller for systems requiring four downstream USB ports rather than a general-purpose USB interface transceiver. Its 40-DIP package favors prototype boards, legacy industrial equipment, and expansion systems where through-hole assembly is acceptable. The supplied listings do not provide a complete official electrical table, exact pin assignments, transfer-rate details beyond USB 1.1, or a current manufacturer lifecycle statement. Those parameters remain identified as data needed rather than being inferred from similar devices. A practical design review should therefore begin with the official TUSB2140B datasheet, especially for D+/D- routing, power-switching requirements, crystal or clock connections, I2C address programming, and termination requirements. In a USB hub design, the controller manages downstream-port enumeration and shared upstream-bus behavior, while external power-distribution and protection components determine how safely multiple peripherals can be connected.

RFQ Contact
TUSB2140N - 4-Port USB 2.0 Hub Controller | Texas Instruments
TUSB2140N

TUSB2140N - 4-Port USB 2.0 Hub Controller | Texas Instruments

Texas Instruments TUSB2140N is a 4-port USB 2.0 hub controller with embedded function, a maximum clock frequency of 48 MHz, I2C bus compatibility, and a 40-pin through-hole DIP package. It is designed for industrial USB hub equipment requiring multiple downstream ports and centralized control. The verified sources identify TUSB2140N as the original 40-PDIP member of the TUSB2140 family and note that it was replaced by TUSB2046B. A USB hub controller is an interface IC that manages traffic between one upstream USB host connection and multiple downstream USB ports. Within the product hierarchy, it is a USB interface controller, bus controller, interface IC, and semiconductor. By organizing USB connectivity and exposing configuration functions through a compatible control bus, this type of device reduces the amount of discrete logic required in a multiport USB product. The TUSB2140N provides four downstream hub ports, operates up to 48 MHz, supports I2C compatibility, and is available in a 40-terminal rectangular DIP package. The verified distributor data classifies it as an industrial-temperature component with through-hole terminals. These characteristics make it relevant to legacy industrial USB hubs, embedded USB expansion equipment, and systems designed around the original TUSB2140 interface rather than newer hub controllers. Technically, the device combines USB host-interface management and an embedded function in one controller. Its 48 MHz maximum operating frequency supports the clocking requirements associated with this USB 2.0 hub-controller generation, while I2C compatibility offers a practical path to configuration and supervisory control. The 40-pin DIP format favors through-hole assembly and repairability, but it consumes considerably more board area than contemporary surface-mount hub controllers. Typical applications include industrial USB hubs, embedded test equipment, peripheral aggregation systems, legacy USB expansion cards, and OEM products that retain the TUSB2140 architecture. Because the part is an older through-hole design, engineers should also assess modern surface-mount alternatives or the indicated TUSB2046B successor when new PCB area, sourcing, or lifecycle constraints favor redesign. The primary design consideration is lifecycle and availability. Verified marketplace data states that TUSB2140N was replaced by TUSB2046B, while current stock and pricing are offered through brokers and distributors. For new production, confirm lifecycle status, exact electrical compatibility, and pin-level equivalence before substituting any successor; a USB hub change can affect enumeration, power management, and downstream-port behavior. This page consolidates verified distributor specifications, the replacement relationship, source links, and engineering selection guidance. It distinguishes documented TUSB2140N attributes from unavailable parameters, helping procurement and design engineers make a grounded legacy-support or migration decision.

RFQ Contact
TUSB2140PAG - 4-Port USB Hub with Embedded Function | Texas Instruments
TUSB2140PAG

TUSB2140PAG - 4-Port USB Hub with Embedded Function | Texas Instruments

Texas Instruments TUSB2140PAG is a 4-port USB hub controller with an embedded function, a 12 Mbps USB interface, a maximum clock frequency of 48 MHz, and a maximum supply voltage of 3.6 V. The device is packaged for surface-mount assembly in a 64-terminal TQFP package. Its combination of USB hub control and embedded functionality is intended for systems that need to consolidate USB connectivity without implementing every protocol and port-management function in external hardware. A USB hub controller is an interface IC that manages one upstream USB connection and multiple downstream ports. The broader hierarchy is USB interface IC, then interface IC, integrated circuit, and semiconductor. Within that hierarchy, the TUSB2140PAG adds an embedded function to the conventional hub role, allowing a compact design to manage USB topology while supporting additional device-specific behavior. This makes the device relevant to USB expansion, embedded control, peripheral aggregation, and legacy USB system designs. Key characteristics include four downstream ports, a 12 Mbps interface, operation with a maximum 3.6 V supply, and support for a 48 MHz maximum clock frequency. The 64-terminal surface-mount package provides the electrical connections required for the upstream interface, downstream ports, power-management signals, clocking, configuration, and embedded-function implementation. Exact pin names, electrical limits, and recommended capacitor values should be confirmed against the manufacturer datasheet before schematic capture or PCB release. Technically, the TUSB2140 belongs to the family of Texas Instruments bus controllers and USB interface integrated circuits. A centralized hub can reduce the number of host USB ports required from an embedded processor or host controller while allowing several peripherals to share one upstream connection. The 48 MHz clock specification defines the device's maximum operating clock, whereas the 3.6 V maximum supply establishes the upper boundary for system-level power design. Designers must also account for USB data-routing topology, termination, decoupling, enumeration behavior, and downstream-port power requirements. Typical applications include industrial USB-to-USB expansion, embedded USB test equipment, peripheral aggregation, legacy computer and communications equipment, and controlled embedded systems requiring more downstream USB connections. The embedded-function architecture may simplify boards that previously required a hub controller plus a separate companion controller, but the exact supported functions and firmware interface must be confirmed for each product design. A key design consideration is to validate signal routing and power sequencing against the complete datasheet before fabrication. Maintain short, continuous USB data paths, provide local high-frequency bypass capacitance at the supply pins, and keep return paths beneath the relevant signals. Do not assume that every device with the same 12 Mbps USB classification is a drop-in replacement; package, pinout, embedded-function behavior, and host compatibility must all match. This product page consolidates verified product identity, package information, lifecycle guidance, substitution limits, comparison fields, and practical USB interface design considerations. It is intended to help engineers identify whether the TUSB2140PAG fits an existing USB hub architecture and which technical checks are required before committing a board revision to production.

RFQ Contact
TUSB214RWBR - USB 2.0 HS Signal Conditioner | Texas Instruments
TUSB214RWBR

TUSB214RWBR - USB 2.0 HS Signal Conditioner | Texas Instruments

Texas Instruments TUSB214RWBR is a USB 2.0 high-speed signal conditioner with DC boost and an integrated BC1.2 Charging Downstream Port controller. It supports USB 2.0, OTG 2.0, and BC1.2 operation, with low-, full-, and high-speed signaling across a 3 V to 3.6 V supply range. The device is packaged in a compact 12-pin X2QFN package measuring 1.6 mm by 1.6 mm. A USB signal conditioner is an interface IC that compensates for attenuation, distortion, and timing degradation introduced by connectors, cables, PCB traces, and other interconnect elements. Positioned within the broader USB interface hierarchy, it sits between a USB host or device controller and a physical USB connection. Its DC boost function helps maintain usable signal amplitude through lossy channels, while its integrated charging-port controller simplifies compliance with BC1.2 downstream-port requirements. The TUSB214 supports LS, FS, and HS signaling and provides selectable signal gain for high-loss applications. Its D1P/M and D2P/M inputs are interchangeable, allowing the same device-oriented layout to work in host or device applications. The device also supports daisy-chain operation, which can simplify cascading through multiple lossy cable or connector sections when a single conditioner is not sufficient. The BC1.2 charging function is configurable through a pin strap or I2C. This provides a practical choice between hardware-configured designs and firmware-controlled implementations. The TUSB214 additionally features very low USB disconnect and shutdown power consumption, making it suitable for power-conscious USB equipment where inactive-state leakage can influence battery life or system thermal performance. Typical applications include USB 2.0 peripheral connections, host-to-cable interfaces, device-to-cable interfaces, and systems that require an integrated downstream charging-port controller. It is particularly useful when PCB routing, connector transitions, or cable loss could degrade high-speed USB data. The 1.6 mm by 1.6 mm X2QFN footprint supports compact designs, although its fine pitch requires careful layout, assembly, and inspection practices. The principal design consideration is placement. The conditioner should be positioned near the loss or connector transition it is intended to correct, while its data traces should remain short, properly terminated, and routed away from noisy power or high-current paths. Designers should also confirm the configured BC1.2 mode, enable state, and signal-gain setting against the final system behavior. This product page combines the TUSB214 family characteristics with package-specific ordering information, application guidance, drop-in alternatives, and a practical comparison framework. It is intended to support component selection and board-level implementation decisions rather than simply repeat the basic catalog description.

RFQ Contact
TUSB214RWBT - USB 2.0 Signal Conditioner | Texas Instruments
TUSB214RWBT

TUSB214RWBT - USB 2.0 Signal Conditioner | Texas Instruments

The Texas Instruments TUSB214RWBT is a USB 2.0 high-speed signal conditioner with a BC1.2 Charging Downstream Port controller, supplied in a 12-X2QFN package measuring 1.6 mm by 1.6 mm. Its primary functions are conditioning high-speed USB data signals and supporting USB battery-charging detection, allowing one compact interface IC to address signal integrity and charging-related system requirements. A USB 2.0 high-speed signal conditioner is an interface IC placed within a USB connection to improve signal transmission behavior. The TUSB214 belongs to the broader hierarchy of USB interface controllers, signal-processing interface ICs, interface ICs, and semiconductors. Its integrated BC1.2 CDP function adds downstream-port charging detection to the high-speed signal-conditioning role, while the manufacturer also identifies compatibility with USB On-The-Go and Battery Charging specifications. The principal feature is consolidation of high-speed USB signal conditioning and BC1.2 CDP detection in one device. The 1.6 mm by 1.6 mm 12-X2QFN package supports compact layouts in USB host, device, docking, and peripheral equipment. Its USB 2.0 high-speed orientation makes it applicable wherever a design uses high-speed USB data paths and requires the additional features of a charging downstream port. From an architectural perspective, the TUSB214 is not a general-purpose USB host controller or a power-path regulator. It is a dedicated signal-processing interface IC. BC1.2 detection identifies whether a connected charging source can supply current, while the signal-conditioning section supports reliable propagation of high-speed USB traffic. This division of responsibilities helps designers avoid assigning charging detection and signal conditioning to unrelated components when a single interface device can address both needs. Typical uses include USB docking stations, laptop peripherals, powered USB devices, multi-interface adapters, and embedded USB equipment. A docking station is a particularly suitable application because it must preserve high-speed data behavior while presenting a downstream charging interface to an attached portable device. The same combination can simplify systems that expose USB-A ports to source equipment while retaining a conditioned high-speed data connection. Layout remains critical because a high-speed signal conditioner must be placed where it can influence the intended USB data path. Follow the manufacturer pin configuration, recommended external components, and trace guidance in the TUSB214 datasheet. Confirm that the selected connector and cable arrangement support USB 2.0 high-speed operation, and validate charging behavior across the system input-current, voltage, and software-handshake requirements. This page combines the exact package and functional information, manufacturer datasheet link, application engineering guidance, lifecycle and compliance fields, and sourcing references. It also distinguishes direct drop-in interchangeability from merely similar USB interface ICs, helping engineers avoid selecting a replacement whose package, pinout, or charging behavior is not compatible.

RFQ Contact
TUSB215RGYR - USB 2.0 HS Signal Conditioner | Texas Instruments
TUSB215RGYR

TUSB215RGYR - USB 2.0 HS Signal Conditioner | Texas Instruments

The Texas Instruments TUSB215RGYR is a USB 2.0 high-speed signal conditioner with DC boost, an integrated Charging Downstream Port, and VBUS supply capability. It operates from a 5 V supply, supports USB 2.0 high-speed signal conditioning, and is packaged in a 14-pin VQFN RGY package measuring 3.5 mm by 3.5 mm. The device is intended to compensate for channel-related signal loss and help improve USB electrical compliance. A USB high-speed signal conditioner is an interface IC placed within a USB differential data path. It belongs to the USB interface and signal-processing hierarchy, where conditioning components address attenuation, edge distortion, and signal integrity before data reaches a host, device, hub, or cable assembly. Unlike a protocol controller, the TUSB215 does not interpret USB transactions; it reshapes the physical-layer signal traveling across the differential pair. The principal features of the TUSB215 include USB 2.0 high-speed operation, DC boost capability, an integrated CDP function, VBUS supply support, and a 14-pin VQFN package. Its operating-temperature range is 0 °C to 70 °C. DC boost compensates for voltage loss encountered in a lossy channel, while the integrated charging function supports downstream-port behavior within compatible USB charging designs. Signal integrity is the central design consideration for this device. TI specifies a 90 Ω differential impedance target for the complete USB high-speed signal path and directs designers to follow high-speed routing guidelines. Differential traces should therefore be length matched, continuously referenced, and routed away from noise-producing or discontinuous structures. Placement close to the source of degradation can provide more effective compensation than placement near the far endpoint. Typical uses include USB 2.0 host-to-device links, hub connections, peripheral docking systems, cable assemblies, and test equipment that needs channel-loss compensation. The TUSB215 is also relevant to boards that require a CDP function within a compact interface subsystem. Designers must still validate the complete USB channel against applicable electrical compliance requirements because component insertion alone does not guarantee system compliance. Thermal and layout planning should begin with the exposed-pad VQFN footprint. Place the input, output, and bypass capacitors close to their associated pins, provide a continuous ground reference, and follow the manufacturer land pattern for exposed-pad soldering. The 3.5 mm by 3.5 mm package supports compact designs, but its small thermal area requires careful copper and return-path construction. This product page combines the device function, package information, application guidance, verified source links, and practical implementation considerations in one engineering-focused reference. It also identifies where electrical details require confirmation in the manufacturer datasheet before a PCB or compliance test is released.

RFQ Contact
TUSB2551PW - USB 2.0 Half Transceiver | Texas Instruments
TUSB2551PW

TUSB2551PW - USB 2.0 Half Transceiver | Texas Instruments

Texas Instruments TUSB2551PW is a single USB 2.0 half-rate transceiver supporting full-speed operation up to 12 Mbit/s and low-speed operation up to 1.5 Mbit/s in a 14-pin TSSOP package. The device operates from a 1.65 V to 3.6 V supply, making it suitable for low-voltage USB connectivity and embedded systems. Its integrated transceiver architecture supports bidirectional USB data signaling while reducing the external circuitry required for a host, device, or interface application. A USB transceiver is an interface IC that converts digital controller signals into USB-compatible physical-layer signals and receives the corresponding bus signals from a USB connection. The TUSB2551 belongs to the USB interface transceiver hierarchy, alongside USB interface controllers, USB hubs, and USB power-management devices. Unlike a USB controller, it does not implement protocol or enumerate bus devices; it provides the physical-layer path between a USB-capable controller and a connector or cable. The TUSB2551 supports both full-speed and low-speed USB 2.0 operation. Texas Instruments identifies superior edge-rate control as a means of producing crisper eye diagrams, which can simplify USB compliance testing. Dual-supply operation allows the digital and analog portions of the device to use separate supply rails. The 1.65 V to 3.6 V operating range supports common 1.8 V and 3.3 V system environments while accommodating lower-voltage interface requirements. Typical uses include USB-to-serial bridges, embedded USB peripherals, industrial data acquisition, portable diagnostic equipment, and USB connectivity for microcontrollers that require an external physical-layer transceiver. Its 14-pin TSSOP format also supports PCB layouts that prioritize a small, widely available package rather than a leadless land pattern. System designers should still verify signal integrity, termination, cable routing, and supply sequencing against the manufacturer datasheet. For USB applications, the transceiver is used between the host or device controller and the connector. Differential pair routing should be short and impedance controlled, while supply and ground connections should provide low-impedance return paths. The device's low-voltage supply range makes it useful for portable equipment, but total system power, connector-current capability, and USB specification compliance remain separate design considerations. This page combines the verified Texas Instruments product information, distributor listings, package details, available cross-reference evidence, and practical guidance for evaluating the TUSB2551PW. It also distinguishes confirmed pin-compatible options from unreported electrical parameters so engineers can identify which data must be checked before approving a replacement.

RFQ Contact
TUSB2551PWR - USB 2.0 Half Transceiver | Texas Instruments (Tape & Reel)
TUSB2551PWR

TUSB2551PWR - USB 2.0 Half Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments TUSB2551PWR is a single USB 2.0 half-rate transceiver supporting full-speed operation up to 12 Mbit/s and low-speed operation up to 1.5 Mbit/s in a 14-pin TSSOP package. The device operates from a 1.65 V to 3.6 V supply, making it suitable for low-voltage USB connectivity and embedded systems. Its integrated transceiver architecture supports bidirectional USB data signaling while reducing the external circuitry required for a host, device, or interface application. A USB transceiver is an interface IC that converts digital controller signals into USB-compatible physical-layer signals and receives the corresponding bus signals from a USB connection. The TUSB2551 belongs to the USB interface transceiver hierarchy, alongside USB interface controllers, USB hubs, and USB power-management devices. Unlike a USB controller, it does not implement protocol or enumerate bus devices; it provides the physical-layer path between a USB-capable controller and a connector or cable. The TUSB2551 supports both full-speed and low-speed USB 2.0 operation. Texas Instruments identifies superior edge-rate control as a means of producing crisper eye diagrams, which can simplify USB compliance testing. Dual-supply operation allows the digital and analog portions of the device to use separate supply rails. The 1.65 V to 3.6 V operating range supports common 1.8 V and 3.3 V system environments while accommodating lower-voltage interface requirements. Typical uses include USB-to-serial bridges, embedded USB peripherals, industrial data acquisition, portable diagnostic equipment, and USB connectivity for microcontrollers that require an external physical-layer transceiver. Its 14-pin TSSOP format also supports PCB layouts that prioritize a small, widely available package rather than a leadless land pattern. System designers should still verify signal integrity, termination, cable routing, and supply sequencing against the manufacturer datasheet. For USB applications, the transceiver is used between the host or device controller and the connector. Differential pair routing should be short and impedance controlled, while supply and ground connections should provide low-impedance return paths. The device's low-voltage supply range makes it useful for portable equipment, but total system power, connector-current capability, and USB specification compliance remain separate design considerations. This page combines the verified Texas Instruments product information, distributor listings, package details, available cross-reference evidence, and practical guidance for evaluating the TUSB2551PWR. It also distinguishes confirmed pin-compatible options from unreported electrical parameters so engineers can identify which data must be checked before approving a replacement.

RFQ Contact
TUSB3200CPAH USB Streaming Controller | Texas Instruments
TUSB3200CPAH

TUSB3200CPAH USB Streaming Controller | Texas Instruments

Texas Instruments TUSB3200CPAH is a USB streaming controller with a standard 8052 microcontroller core, 4 KB of ROM program memory, and full compatibility with USB Specification Version 1.1 and the USB Audio Class Specification. The device is packaged in a 52-pin TQFP and is intended for USB audio interface designs that require dedicated USB streaming control. A USB streaming controller is a specialized application-specific microcontroller that manages the transfer of audio or other streaming data between a USB host and an audio codec or peripheral. Within the product hierarchy, it combines an 8052 microcontroller, USB device control, firmware handling, and streaming interfaces. This integration reduces the need for a separate general-purpose controller when a USB audio product requires deterministic enumeration, control, and data-routing behavior. Key characteristics include the 8052 MCU architecture, 4 KB ROM containing a bootloader program, USB 1.1 compatibility, and USB Audio Class support. The dedicated streaming architecture allows a product to handle USB host enumeration and audio data transfer while presenting the external audio circuitry with a controlled interface. The 52-pin TQFP also provides separate connections for digital audio, USB, clocking, control, and power functions. The controller's internal organization is centered on on-chip memory and an 8052-compatible processing core. Its ROM-based program memory contains a bootloader, while USB and audio-class firmware establish enumeration and streaming behavior. This makes the device suitable for compact USB audio equipment where a dedicated streaming interface is preferable to implementing the complete USB audio stack in a larger application processor. Typical applications include USB headphones, active speakers, USB speakerphones, docking stations, USB audio adapters, and compact consumer audio accessories. In these systems, the TUSB3200CPAH can manage USB streaming control while an external codec converts the digital stream into an analog or headphone-driver-compatible signal. Its dedicated function also supports multi-function USB products that combine audio with control or status interfaces. PCB design should preserve the USB differential pair as a short, continuous, impedance-controlled route and place the required support components close to the device. Audio and USB clock domains require careful grounding and return-path planning to prevent data corruption and audible artifacts. Designers should use the manufacturer pin-description and layout guidance when assigning every TQFP signal and programming the on-chip firmware. This product page combines the exact TUSB3200CPAH identification, USB streaming architecture, verified package details, sourcing guidance, related 52-TQFP options, and practical implementation considerations. It is designed to help engineers determine whether the controller matches a USB audio design before beginning PCB layout and firmware integration.

RFQ Contact
TUSB320HAIRWBR - USB Type-C CC Logic, X2QFN-12 | TI
TUSB320HAIRWBR

TUSB320HAIRWBR - USB Type-C CC Logic, X2QFN-12 | TI

The Texas Instruments TUSB320HAIRWBR is a USB Type-C Configuration Channel (CC) logic and port controller in an industrial-grade (I-temp) active-high enable variant, packaged in a 12-pin X2QFN (RWB) measuring 1.6 mm × 1.6 mm. The device operates from a single 3.3 V supply and supports USB Type-C Specification 1.1 while remaining interoperable with 1.0 systems. It advertises and detects up to 3 A of VBUS current per Type-C current-mode rules and supports DFP (Source), UFP (Sink), and DRP (Dual Role) port roles selected through MODE pins. A USB Type-C Configuration Channel Logic IC is a state-machine controller that sits between a USB Type-C receptacle and the application processor or USB controller. Its job is to negotiate attach/detach events, cable orientation (CC1/CC2 polarity), role (host vs device), and current advertisement (default 500 mA, 1.5 A, or 3 A) through the CC1/CC2 pull-up and pull-down signalling defined by the USB-IF Type-C specification. Higher up the hierarchy it is an Interface IC > USB Interface IC; below it is the CC PHY layer. Key features include: integrated 5.1 kΩ CC pull-up resistors that can be toggled for DRP toggle, hardware MODE pin configuration (no firmware needed), active-high enable (EN) pin for power sequencing, low standby current with a dedicated low-power mode, and HBM ESD protection on CC pins. The X2QFN-12 RWB package keeps the device under 3 mm² footprint, ideal for compact dongles, hubs, and embedded platforms. Typical applications are any 5 V / 3 A USB Type-C ports that need a low-BOM CC controller: travel chargers, USB Type-C dongles, adapters, hubs, docking stations, smartphones, tablets, and notebooks. Because it operates as a standalone state machine with no MCU required, it is well-suited to cost- and board-area-sensitive designs. Design consideration: place the 100 nF decoupling capacitor within 2 mm of VCC and keep the CC traces short, matched, and away from switching nodes to preserve signal integrity. A 0 Ω or ferrite series resistor on VBUS is optional but recommended to limit inrush current at attach. This page synthesizes distributor pricing, drop-in alternatives, application pairings, and design notes not found in the manufacturer datasheet, optimized for engineers sourcing USB Type-C port controllers.

RFQ Contact
TUSB320LAIRWBR - USB Type-C CC Logic & Port Controller | TI
TUSB320LAIRWBR

TUSB320LAIRWBR - USB Type-C CC Logic & Port Controller | TI

The Texas Instruments TUSB320LAIRWBR is a USB Type-C configuration channel (CC) logic and port controller housed in a 12-pin X2QFN (RWB) package measuring 1.6 mm x 1.6 mm. It supports USB Type-C Specification 1.1, is backward compatible with 1.0, advertises and detects up to 3 A of VBUS current, and operates from a 2.7 V to 5 V supply. Configuration modes include Host Only (DFP/Source), Device Only (UFP/Sink), and Dual Role Port (DRP) for accessories, hubs, smartphones, and laptops. The "L" variant removes I2C and adds GPIO-controlled mode selection for ultra-low-power BOMs. What is a USB Type-C port controller? A USB Type-C port controller is an interface IC that sits between a USB 2.0 data path and the Type-C receptacle, managing the Configuration Channel (CC) pins that detect cable attach/detach, determine plug orientation (CC1 vs CC2), advertise the source/sink current capability through Rp/Rd pull-up/pull-down resistors, and negotiate power-role swap for USB Power Delivery. It belongs to the broader hierarchy of interface ICs -> USB interface ICs -> Type-C controllers -> USB Power Delivery controllers, occupying the link layer just above the physical connector. Key differentiating features include integrated CC logic, automatic DRP toggle, support for audio and debug accessory modes, an active-high ENABLE pin, and an open-drain INT output for interrupt-driven host polling. The device is offered in both I2C-configurable (TUSB320I) and pin-strapped/GPIO (TUSB320L) variants within the same X2QFN-12 footprint, allowing PCB reuse between firmware-driven and BOM-optimized designs. Operating temperature is -40 C to +85 C (industrial). The TUSB320L architecture is a pure hardware state machine that samples the CC1/CC2 pins, drives the appropriate Rp current source or Rd pull-down, and reports attach/orientation events to the application processor through dedicated GPIO flags. This eliminates the firmware overhead of I2C register polling and reduces quiescent current for battery-powered devices. Compared to discrete USB-C implementations using comparators and FETs, the TUSB320L integrates Rp/Rd biasing and accessory detection in a single 1.6 mm x 1.6 mm chip. Typical applications include USB Type-C wall adapters, smartphone charging cradles, accessory-mode audio adapters, USB-C hubs and docks, notebook and tablet Type-C ports, and USB-C debug ports for embedded development. It is widely used wherever a 5 V / up to 3 A Type-C source or sink is needed without USB PD negotiation. A key design tip - because the TUSB320L has no I2C, role selection and current-mode advertisement must be hard-wired through MODE pin resistors at power-up. Layout the CC1/CC2 traces as a 90 ohm differential pair with the connector ground return, and decouple VDD with a 0.1 uF X7R ceramic placed within 2 mm of pin 12. This page synthesizes TI datasheet parameters, distributor pricing, drop-in alternatives (same-brand first, cross-brand verified), and PCB design notes not duplicated in the manufacturer datasheet, giving procurement and design engineers a one-stop reference for the TUSB320LAIRWBR.

RFQ Contact
TUSB320RWBR - USB Type-C CC Controller | Texas Instruments
TUSB320RWBR

TUSB320RWBR - USB Type-C CC Controller | Texas Instruments

Texas Instruments TUSB320RWBR is a USB Type-C configuration channel logic and port-control IC supporting USB Type-C specification 1.1, backward compatibility with specification 1.0, and current advertisement and detection up to 3 A. The device is offered in a 12-X2QFN surface-mount package measuring 1.6 mm by 1.6 mm. It handles configuration-channel attachment, cable-orientation detection, port-role detection, and Type-C current-mode selection. A USB Type-C configuration channel controller is an interface IC within the USB Type-C port ecosystem. USB Type-C uses dedicated CC pins to negotiate cable attachment, orientation, port roles, and the available current level. This controller connects that negotiation to the port-management circuitry, allowing a USB-C port to operate as a source, sink, or dual-role port without implementing the entire USB Type-C protocol in system firmware. The TUSB320 supports host-only DFP, device-only UFP, and dual-role DRP operating modes. It advertises default, medium, and high Type-C current modes, with support for current advertisement and detection up to 3 A. Backward compatibility with USB Type-C specification 1.0 is important when the port must interoperate with earlier implementations and accessories. Its compact 1.6 mm by 1.6 mm package supports space-constrained consumer and embedded systems. Technically, the device separates low-speed Type-C port management from the data path. CC signaling determines which direction the inserted cable is connected and which party supplies power, while the USB data lanes remain the responsibility of a host, device, or dual-role controller. This division improves design flexibility because the same connector can be used with several USB controllers or protocol bridges when their electrical and logical interfaces are compatible. Typical applications include laptop and tablet docking stations, smartphone and accessory charging designs, USB-C expansion adapters, industrial USB-C equipment, and embedded systems that require reversible connector orientation detection. It is also suitable for USB-C power-management designs where the system must identify sink or source behavior before enabling the appropriate power path. Designers should verify the exact pin assignments, electrical limits, VBUS behavior, and configuration-channel implementation against the manufacturer datasheet. PCB layout must keep the compact package’s connections short, provide clean device grounding, and follow the manufacturer’s recommended decoupling arrangement. Because the controller coordinates port behavior rather than carrying high-speed USB data, its placement priority is deterministic power sequencing and signal integrity rather than USB differential-pair routing. This product page consolidates the TUSB320RWBR specifications, verified manufacturer and distributor links, family alternatives, comparison parameters, and practical selection guidance. It is intended to help engineers determine whether the 12-X2QFN Type-C controller supports their required roles, current mode, package, and system-management architecture.

RFQ Contact
TUSB3210PM - USB 2.0 8052 Controller | Texas Instruments
TUSB3210PM

TUSB3210PM - USB 2.0 8052 Controller | Texas Instruments

The Texas Instruments TUSB3210PM is an integrated USB 2.0 full-speed general-purpose device controller with an 8052-based microcontroller, 8K x 8 RAM, and programmable general-purpose I/O in a 64-pin LQFP package. It supports USB data rates up to 12 Mbit/s and provides USB suspend, resume, and remote wake-up operation for connected peripheral, control, and human-interface-device designs. A USB general-purpose device controller is an application-specific microcontroller category that integrates a USB full-speed serial interface with embedded firmware execution and general-purpose I/O. The TUSB3210 sits within the hierarchy of semiconductor, embedded microcontroller, application-specific microcontroller, and USB interface controller devices. This integration reduces the need for a separate USB interface IC while retaining programmable behavior for product-specific USB functions. The principal feature set includes USB 2.0 full-speed compliance, a 12 Mbit/s supported USB data rate, suspend, resume, and remote wake-up support, and 8K x 8 bytes of RAM for application development. The controller also supports multiproduct designs with one code base and one controller, including configurations covering up to 16 products with one chip. Its programmability allows the same USB-connected platform to address multiple peripheral roles without relying on a fixed-function bridge. Internally, the TUSB3210 combines an 8052-compatible microcontroller with USB device-controller logic and general-purpose I/O. The 8K x 8 RAM organization provides 8,192 bytes of data storage for firmware variables, descriptors, buffers, and working state. Because the part is programmable rather than a fixed protocol translator, engineers can implement device-specific enumeration behavior, vendor requests, HID reports, status signaling, or other USB functions in one compact 64-LQFP device. Typical implementations include USB-to-serial adapters, keyboard and mouse controllers, industrial input modules, portable diagnostic equipment, programmers, and general USB I/O expansion boards. The 64-pin LQFP package also exposes enough pins for multiple GPIO functions, clocking connections, and USB bus-interface requirements, although a complete 64-pin pin map is not present in the supplied verified excerpts. The principal design consideration is that USB firmware, descriptor development, and bus-routing validation remain necessary because this is a programmable controller rather than a fully finished USB peripheral. Layout should follow the manufacturer's recommended USB data-path guidance, provide clean return-current paths, and use appropriate decoupling. Exact operating-voltage, clock, temperature, and pin-function details should be confirmed in the manufacturer datasheet before schematic release. This page consolidates the verified distributor identification, USB 2.0 and 8052 controller description, package information, RAM capacity, pricing indication, and sourcing links into an engineering-focused view. It also separates verified facts from unavailable detailed specifications and documents why few defensible drop-in replacements can be confirmed from the supplied cross-reference results.

RFQ Contact
TUSB3210PMG4 - 3.3V USB 2.0 8052 MCU | Texas Instruments
TUSB3210PMG4

TUSB3210PMG4 - 3.3V USB 2.0 8052 MCU | Texas Instruments

Texas Instruments TUSB3210PMG4 is an application-specific USB microcontroller with an 8052 core, USB 2.0 interface, 3.3 V supply operation, and integrated EEPROM in a 64-pin LQFP package. It is packaged in a tray for commercial-temperature production systems. An application-specific microcontroller is an embedded processing IC optimized for a defined peripheral function or interface rather than for general application processing. The TUSB3210 belongs to the microcontroller hierarchy, combining an 8052-compatible CPU core with a USB device controller, on-chip program memory, RAM, and EEPROM. This integration allows a USB-to-GPIO or similar peripheral design to enumerate as a full-speed USB device while reducing the number of external components. The principal operating characteristics are a 3.3 V supply, USB 2.0 full-speed connectivity, an 8052 microcontroller core, and a 64-terminal LQFP package. Its 64 terminals provide access to the controller, firmware-programmable I/O, clock, reset, power, and USB functions. The G4 ordering designation corresponds to the commercial-temperature, tray-packaged configuration identified in the Texas Instruments product information. TUSB3210PMG4 integrates USB connectivity with programmable GPIO behavior rather than requiring a conventional USB PHY and external microcontroller as separate components. The EEPROM supports configuration or parameter retention, while the 8052 core executes the device firmware that identifies the peripheral and controls its external interfaces. Because the device is a dedicated USB controller, its principal engineering task is validating the complete pin, firmware, timing, and USB enumeration design before a board is released. Typical applications include USB-to-GPIO adapters, configurable peripheral controllers, data-acquisition front ends, legacy equipment interfaces, and industrial interface modules. The integrated USB controller can also support firmware-based product identification, control, and status reporting over a full-speed USB connection. External transceivers, protection components, crystals, and storage may still be required according to the selected board architecture. Use the manufacturer pin-description table and reference schematic when assigning PCB tracks, especially for USB data, clock, reset, and exposed supply connections. Preserve the specified decoupling arrangement, maintain controlled USB impedance routing, and validate firmware behavior across bus-powered and externally powered operating conditions. This page combines the manufacturer catalog identity, verified package and ordering information, a strict drop-in replacement assessment, and practical implementation guidance. It also distinguishes the electrically and mechanically interchangeable ordering option from devices that only perform a similar USB-interface function but do not share the 64-pin LQFP footprint.

RFQ Contact
TUSB321RWBR - USB Type-C CC Logic 3A X2QFN-12 | Texas Instruments
TUSB321RWBR

TUSB321RWBR - USB Type-C CC Logic 3A X2QFN-12 | Texas Instruments

The Texas Instruments TUSB321RWBR is a USB Type-C configuration channel (CC) logic and port control device with VCONN support, packaged in a 12-pin X2QFN (1.6x1.6 mm) land-grid array. It implements the CC signaling required by USB Type-C Specification 1.1 and remains backward compatible with USB Type-C Specification 1.0, advertising up to 3 A of current through a dedicated current mode pin. A USB Type-C CC logic device is a specialized interface IC that manages the configuration channel pins of a USB Type-C connector. Within the system hierarchy, it sits between the USB Type-C connector and the USB controller or power path, belonging to the interface IC family inside integrated circuits. The CC logic block monitors the CC1 and CC2 pins for pullup or pulldown resistances to determine port attach and detach, cable orientation, and role detection, which are mandatory functions for any Type-C port. Key features include three mode configurations - host only (DFP/Source), device only (UFP/Sink), and dual role port (DRP) - where the device alternates between DFP and UFP roles per the Type-C Specifications. An integrated VCONN switch powers electronically marked (e-marked) cables, and dead battery mode allows a sink device to present as a Type-C device even before system power is available. Technically, the TUSB321 integrates CC termination, Rp/Rd detection, cable orientation indication, and port power control in a single low-power die, minimizing external components and bill-of-materials cost. The compact X2QFN package with 1.6x1.6 mm footprint suits space-constrained portable designs. Typical applications include smartphones, tablets, laptops, docking stations, chargers, and USB Type-C enabled accessories. Any design needing compliant Type-C attach detection and current advertisement benefits from this device. For design, place the TUSB321RWBR close to the Type-C connector to keep CC traces short, decouple VCC with a 1 uF capacitor, and configure the current mode pin for the intended 3 A advertisement level as described in TI datasheet (SLVSDF4).

RFQ Contact
TUSB321RWBR-Q1 - USB Type-C CC Logic Port Control | TI
TUSB321RWBR-Q1

TUSB321RWBR-Q1 - USB Type-C CC Logic Port Control | TI

The Texas Instruments TUSB321RWBR-Q1 is an automotive-grade USB Type-C configuration channel (CC) logic and port control IC with VCONN support, provided in a compact 12-pin X2QFN package measuring just 1.6 mm x 1.6 mm. Operating from a 4.5V to 5.5V supply, it enables USB Type-C ports with the CC logic needed for Type-C ecosystems while meeting the USB Type-C Specification 1.1 and remaining backward compatible with Specification 1.0. A USB Type-C port controller (also called a CC logic chip or port control IC) is a small companion device that manages the configuration channel pins of a Type-C connector. It sits in the hierarchy: port controller -> USB interface IC -> USB connectivity semiconductor -> power/data management. It detects attach and detach events, determines cable orientation, performs role detection, and advertises current capability through the dedicated current mode pin. Key features include support for up to 3A of current advertisement through the dedicated current mode pin, configurable port roles of DFP (source), UFP (sink), or dual role port (DRP), and integrated VCONN supply switching for actively marked cables. The device autonomously handles Rd/Rp termination switching on the CC pins according to cable orientation, offloading this logic from the system microcontroller. The TUSB321 implements the CC layer with a simple pin-strap configuration (PORT pin) rather than an I2C interface, minimizing firmware complexity and cost for systems that do not need Power Delivery negotiation. Its automotive qualification (AEC-Q100) makes it suitable for infotainment, telematics, and charging ports in vehicles, while the 1.6 mm x 1.6 mm X2QFN footprint fits space-constrained smartphone, tablet, and accessory designs. Typical applications include automotive USB Type-C charging ports, host and device port attach detection in notebooks, docking stations, and power-bank sink/source role management. Design tip: strap the PORT pin for the required role at power-up; if you later need USB Power Delivery negotiation, migrate to the I2C-controlled TUSB322 family, which shares the same X2QFN footprint.

RFQ Contact
TUSB3410IRHB UART-I2C-IrDA USB Bridge | Texas Instruments
TUSB3410IRHB

TUSB3410IRHB UART-I2C-IrDA USB Bridge | Texas Instruments

Texas Instruments TUSB3410IRHB is an application-specific 8052 USB serial-port controller that bridges an enhanced UART serial port to USB while also supporting I2C and IrDA connectivity. The device operates from 3.0 V to 3.6 V and is offered in a 32-pin VQFN RHB package with an exposed pad for an industrial temperature range of -40°C to +85°C. A USB-to-UART bridge is an interface controller that translates transactions between a USB host and an embedded serial device. The TUSB3410 belongs to the broader USB interface-controller hierarchy and combines a USB interface, enhanced UART, I2C connectivity, IrDA support, and an embedded 8052 microcontroller. This integration allows legacy serial equipment to communicate through a USB connection without requiring a separate external host controller. The TUSB3410 contains an 8052 microcontroller core with 10 KB of ROM and 16 KB of RAM. Its ROM contains firmware supporting the bridge functions, while RAM can be loaded by the USB host or through external onboard memory connected by I2C. The RHB package provides 32 pins and an exposed thermal pad, enabling a compact surface-mount implementation with an effective PCB heat-spreading area. The 3.0 V to 3.6 V operating range suits systems that use a 3.3 V power rail. In the UART path, the device bridges USB to an enhanced serial interface, and its I2C capability supports access to external memory or configuration devices. IrDA support provides an infrared-oriented serial path, although the selected external transceiver, optical interface, and application circuitry remain important parts of the complete design. Typical uses include legacy serial-port adapters, industrial equipment interfaces, point-of-sale systems, laboratory data acquisition, embedded-control service ports, and infrared-capable peripheral connections. The same bridge architecture can simplify host software when existing equipment already communicates through UART while preserving the familiar serial protocol at the device side. PCB implementation should follow the manufacturer pin and land-pattern guidance for the RHB package. Keep USB traces short and controlled, connect the exposed pad to the appropriate ground plane, provide decoupling close to the supply pins, and route high-speed or infrared-associated interfaces according to their respective signal-integrity requirements. Confirm unused control-pin states in the device documentation before finalizing the schematic.

RFQ Contact
TUSB3410IVF - USB to UART Bridge | Texas Instruments
TUSB3410IVF

TUSB3410IVF - USB to UART Bridge | Texas Instruments

Texas Instruments TUSB3410IVF is a USB-to-UART bridge controller with an integrated 8052 microcontroller, 10 kB ROM, UART, I2C, and IrDA support, and a 32-pin LQFP (VF) package. It operates from a 3 V to 3.6 V supply and is specified for temperatures from -40°C to +85°C, making it suitable for industrial embedded-control systems that need to connect a legacy UART or IrDA peripheral to a USB host. A USB-to-UART bridge is an interface IC that translates between the packet-based Universal Serial Bus and a character-oriented serial peripheral. Positioned within interface ICs, bridge controllers, serial interface devices, and data-conversion semiconductors, the TUSB3410 reduces the need for a host to implement a proprietary serial protocol directly. Its integrated controller manages USB-to-serial command exchange while external circuitry connects to the system-side serial interface. The TUSB3410IVF combines a 3 V to 3.6 V operating range with integrated ROM and an industrial temperature grade. Its supported UART, I2C, and IrDA connectivity allows one bridge to serve conventional serial equipment or infrared-oriented peripherals. The 32-lead LQFP package provides a conventional surface-mount footprint suitable for automated assembly and compact industrial controller layouts. The device is built around an 8052-compatible microcontroller core with 10 kB of ROM, as identified in the manufacturer product listing. Firmware or configuration can be loaded by the USB host or through external onboard memory using I2C, according to the device documentation. This architecture makes the bridge useful when peripheral behavior must be adapted through firmware rather than implemented entirely in fixed hardware. Typical applications include industrial serial adapters, USB-connected control panels, legacy equipment interfaces, infrared data links, configuration ports, and embedded systems requiring a USB uplink from a UART-based peripheral. The industrial temperature specification supports equipment deployed in factory, instrumentation, and communications environments where consumer-temperature components may be unsuitable. Designers should preserve the exact pin assignments and reference circuitry shown in the manufacturer datasheet, especially for external memory, clock, USB, and serial-interface connections. Power and decoupling should follow the recommended topology, while USB signal routing requires a controlled impedance path and short connection from the controller to the connector. This product page combines the official device description, package and temperature information, replacement considerations, and design-focused guidance. It highlights the practical trade-offs between the industrial TUSB3410IVF and related TUSB3410 ordering variants while keeping sourcing and technical decisions tied to manufacturer documentation.

RFQ Contact
TUSB3410RHB - USB to UART Controller | Texas Instruments
TUSB3410RHB

TUSB3410RHB - USB to UART Controller | Texas Instruments

Texas Instruments TUSB3410RHB is a full-speed USB 2.0 to enhanced-UART serial-port controller with an integrated 8052 microcontroller, 10 KB ROM, and 16 KB RAM in a 32-pin VFQFN package with exposed pad. It bridges a USB host connection to an enhanced UART peripheral, allowing legacy serial equipment to use USB without changing its host-side application interface. A USB serial-port controller is a type of interface bridge that translates USB traffic into a conventional serial protocol. In the product hierarchy, the TUSB3410 belongs to interface ICs, USB-to-serial converters, communication bridges, and embedded connectivity semiconductors. Its internal microcontroller can configure the USB interface during boot, load code from the host or external memory through I2C, and support firmware-based adaptation of the UART-facing device. The TUSB3410 family includes 10 KB of ROM for USB boot configuration and 16 KB of RAM available for loading from the host or external onboard memory through I2C. Its USB interface operates at full speed under USB 2.0, while the serial side uses an enhanced UART. The integrated controller reduces the need for an external USB interface microcontroller in legacy serial-port designs. The 32-pin VFQFN exposed-pad package supports compact PCB layouts, but the thermal pad must be connected to the appropriate ground plane. The manufacturer datasheet identifies TUSB3410 as a USB-to-serial-port controller and documents the device as production data. Package, pin, and electrical details should be checked against the current manufacturer datasheet before layout release. Typical uses include legacy industrial serial adapters, POS and peripheral interfaces, data-collection equipment, embedded service ports, and USB-to-UART retrofit products. The internal RAM and ROM are especially useful when the adapter needs device identification, configuration, or firmware loaded by the USB host. A key design consideration is that this device is a protocol controller rather than a complete USB-to-RS-232 electrical transceiver. If the remote endpoint requires RS-232 voltage levels, IrDA signaling, or galvanic isolation, add the appropriate line-driver, receiver, and protection circuitry. This page combines the manufacturer interface description with package-focused alternatives and engineering guidance for USB-to-UART designs. It helps engineers evaluate firmware loading, exposed-pad layout, external-interface requirements, and the distinction between protocol conversion and physical-layer conversion before selecting a replacement.

RFQ Contact
TUSB3410RHBR - USB 2.0 UART Bridge | Texas Instruments
TUSB3410RHBR

TUSB3410RHBR - USB 2.0 UART Bridge | Texas Instruments

The Texas Instruments TUSB3410RHBR is a USB 2.0 full-speed serial-port controller that bridges one enhanced UART channel to USB and supports UART, I2C, and IrDA serial-port operating modes. It integrates an 8052-compatible core with 10 kB of ROM, provides 32 package pins, and is offered in a VQFN RHB package with an exposed thermal pad. Its specified commercial temperature range is 0°C to 70°C. A USB serial bridge is an interface IC that translates between a USB host and an embedded serial device. Within the product hierarchy, the TUSB3410 is a USB interface controller, serial-port bridge, application-specific microcontroller, and power-management-independent semiconductor. This category allows legacy RS-232, RS-485, IrDA, and related serial equipment to connect through a standardized USB port without redesigning the host-side interface. Key features include full-speed USB operation, support for an enhanced UART channel, I2C and IrDA functionality, an 8052 controller core, and 10 kB of ROM. The RHB package exposes a pad for improved heat transfer on compact circuit boards. These features suit equipment that needs a direct USB-to-serial path while retaining control over modem-style UART handshake signals. The TUSB3410 integrates an 8052-compatible microcontroller architecture with USB and serial-port functions rather than behaving as a passive level translator. Its internal ROM supports device operation, while external circuitry handles the selected physical serial interface. For RS-232 designs, an external transceiver is required for voltage conversion and line protection; for RS-485 designs, the appropriate transceiver and termination network must likewise be selected separately. Typical applications include USB-to-RS-232 adapters, industrial serial equipment, configuration and debug ports, infrared data links, USB-to-IrDA adapters, and legacy serial accessories. The device is also suitable for data acquisition and control equipment that uses handshake signals to coordinate transmitter and receiver activity. PCB design should preserve the exposed-pad thermal path and keep USB, crystal, and serial-interface routing away from noisy power stages. Confirm the unused hardware-control-pin states against the manufacturer's pin-description table and interface guidance. Review the exact electrical limits, clock requirements, and transceiver interface details before releasing a production design. This page consolidates package, interface, temperature, lifecycle, compliance, replacement, and application guidance while adding practical PCB and design considerations. It also identifies same-footprint TUSB3410 family options so engineers can distinguish electrical-temperature variants from reel or small-reel ordering codes without changing the PCB land pattern.

RFQ Contact
TUSB3410RHBT - USB Serial Port Bridge | Texas Instruments
TUSB3410RHBT

TUSB3410RHBT - USB Serial Port Bridge | Texas Instruments

The Texas Instruments TUSB3410RHBT is an application-specific 8052 USB serial port controller with 10 kB of ROM, UART, I2C, and IrDA connectivity, and USB interface support. It is packaged in a 32-pin VQFN RHB package rated for a 0°C to 70°C operating range. The device bridges USB connectivity with legacy serial interfaces while providing four I/O lines for peripheral control. A USB serial port controller is an interface integrated circuit that allows equipment using UART, I2C, or IrDA serial signaling to communicate through a USB host. Within the product hierarchy, it belongs to the USB interface IC and application-specific microcontroller categories, combining firmware-driven control, USB device logic, and serial-port connectivity in one component. The TUSB3410 includes an 8052 core, 10 kB of ROM, four I/O lines, and support for UART, I2C, IrDA, and USB serial functions. Its integrated design reduces the need for separate USB-to-serial interface hardware while retaining the familiar serial connectors and signal levels used by established industrial and embedded equipment. The manufacturer datasheet explains that USB compliance requires the device to become ready to respond to the host within 100 ms. During this interval, the controller must leave reset, load configuration data from an I2C EEPROM when applicable, and transfer execution to application firmware. This startup sequence is important when validating USB enumeration and host-driver compatibility. Typical uses include USB-to-UART adapters, industrial data-collection equipment, IrDA peripherals, legacy serial-console systems, and USB-to-I2C bridges. The TUSB3410 is particularly relevant when an existing serial-port design must become USB-compatible without changing the host-side application software around the serial interface. Design the power, USB, UART, I2C, and optional IrDA sections according to the manufacturer datasheet. Keep USB routing compact and controlled, provide the required input and output capacitance at the device, and account for EEPROM access and firmware startup before expecting the host to communicate successfully. This page combines manufacturer device information, verified commercial references, drop-in cross-reference results, and practical selection guidance. It also distinguishes confirmed drop-in options from functional alternatives that require a different footprint, helping engineers avoid substitutions that cannot be soldered onto the original PCB land pattern.

RFQ Contact