Products (44,000+)

LAN7800/VSX USB 3.1 Gen1 to Gigabit Ethernet Bridge | Microchip Technology
LAN7800/VSX

LAN7800/VSX USB 3.1 Gen1 to Gigabit Ethernet Bridge | Microchip Technology

The Microchip Technology LAN7800/VSX is a single-chip SuperSpeed USB 3.1 Gen1 to 10/100/1000 Ethernet controller with an integrated Gigabit Ethernet PHY, supplied in a 48-pin SQFN package measuring 6 x 6 mm. It combines a USB device controller, 10/100/1000 Base-TX Ethernet MAC, and integrated PHY to add wired network connectivity through one USB port. The device targets docking stations, set-top boxes, PVRs, port replicators, USB-to-Ethernet dongles, embedded systems, and test instrumentation where a compact, bus-powered network interface is valuable. An Ethernet controller is an interface integrated circuit that manages data exchange between a host computer or embedded processor and a physical Ethernet network. This LAN7800 bridges SuperSpeed USB 3.1 Gen1 traffic to copper Ethernet, supporting 10, 100, and 1000 Mb/s operation. Its integrated PHY reduces the need for a separate physical-layer transceiver, while the integrated USB and Ethernet blocks simplify host-side software connectivity through standard network-device operation. The key verified feature set includes SuperSpeed USB 3.1 Gen1 connectivity, a 10/100/1000 Ethernet controller interface, and an integrated 10/100/1000 Ethernet PHY. Microchip describes the LAN7800 as a high-performance, cost-effective USB-to-Ethernet connectivity solution. The 48-SQFN package supports compact PCB designs, but its exposed thermal pad and high-speed interfaces require careful layout and thermal implementation. The controller is designed for USB 3.1 Gen1-to-Gigabit Ethernet conversion rather than general-purpose data acquisition. Its USB side connects to a modern host or embedded system, while its Ethernet side connects to a network through an RJ45 module and appropriate magnetic isolation or magnetics. USB bus power can support portable dongle designs, while external power may be required depending on the implementation and operating mode. Typical applications include notebook and tablet docking stations, USB port replicators, set-top boxes, personal video recorders, embedded Linux systems, USB-to-Ethernet adapters, and test equipment. The LAN7800 is particularly useful when a product needs one USB connection to provide reliable wired Ethernet without adding a separate host Ethernet PHY or a large external bridge assembly. For layout, follow Microchip’s published LAN7800 schematic checklist and evaluation-board guidance. Pay particular attention to the high-speed USB differential pair, Ethernet differential pairs, power rails, decoupling, return paths, and exposed-pad connection. Confirm the exact package pin assignments and electrical limits against the current manufacturer datasheet before release to production. This page combines the verified manufacturer and distributor information for LAN7800/VSX with application guidance, design cautions, and a comparison framework. It helps engineers determine whether the integrated USB-to-Gigabit Ethernet bridge fits a docking, embedded, or adapter design before completing board-level validation.

RFQ Contact
LAN7800T/VSX - USB 3.1 Gen1 to Gigabit Ethernet Bridge | Microchip
LAN7800T/VSX

LAN7800T/VSX - USB 3.1 Gen1 to Gigabit Ethernet Bridge | Microchip

The Microchip LAN7800T/VSX is a SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet bridge controller, housed in a 48-pin SQFN (6x6 mm) package with exposed pad. It integrates a 10/100/1000 Mbps Ethernet PHY, USB 3.1 Gen 1 device controller, and on-chip PHY in a single chip, enabling ultra high-performance USB-to-Ethernet connectivity at 5 Gbps SuperSpeed rates. What is a USB-to-Ethernet bridge controller? A USB-to-Ethernet bridge is a peripheral controller IC that presents itself to a host system as a USB device on one side and an Ethernet MAC/PHY on the other side. In the broader component taxonomy, it is a type of USB interface IC and network interface controller (NIC), belonging to the connectivity IC family within interface and networking semiconductors. The bridge allows devices without built-in Ethernet (single-board computers, tablets, embedded systems, USB-C docking stations) to add wired GbE connectivity through a standard USB port. Key features of the LAN7800T/VSX include 10/100/1000 Base-TX PHY interface, support for USB 3.1 Gen 1 (SuperSpeed, 5 Gbps), Wake-on-LAN (WoL), Energy Efficient Ethernet (EEE), VLAN filtering, programmable packet filtering, multicast filtering, and programmable LED indication. The device operates from 1.2V and 2.5V supply rails (typical of USB PHY and Ethernet PHY subsystems), and supports low-power modes including modern standby and wake-on-LAN event resume signaling to the host. The LAN7800T/VSX uses an integrated PHY with HP Auto-MDIX support, eliminating the need for crossover cables. The integrated USB 3.1 Gen 1 PHY includes spread-spectrum clocking for EMI reduction, and the Ethernet side integrates 10BASE-Te, 100BASE-TX, and 1000BASE-T PHYs. The device supports IEEE 802.3az Energy Efficient Ethernet (EEE) and is AEC-Q100 qualified through its automotive-grade sister variant LAN7800T-I/VSX, making the platform suitable for industrial, commercial, and selected automotive-grade applications. Typical applications include USB-C dongles and adapters, single-board computer (Raspberry Pi, etc.) wired networking, USB docking stations, embedded industrial gateways, point-of-sale (POS) terminals, and USB-attached network-attached storage (NAS) bridges. Industrial temperature variants (-40C to +85C) are also available under the same LAN7800 silicon. When designing with this device, the primary PCB consideration is the 48-pin SQFN exposed pad. The EP must be soldered to a sufficiently large copper ground pour on the top layer with multiple thermal vias to inner ground planes to dissipate heat from GbE operation and provide a low-impedance ground reference for the integrated PHY. USB 3.1 Gen 1 routing demands 90-ohm differential impedance with length matching. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations not found in the standalone Microchip datasheet.

RFQ Contact
LAN7801T-I/9JX - USB 3.1 Gen1 to GbE Bridge | Microchip | RGMII
LAN7801T-I/9JX

LAN7801T-I/9JX - USB 3.1 Gen1 to GbE Bridge | Microchip | RGMII

The Microchip LAN7801T-I/9JX is a SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet bridge controller delivering high-performance USB-to-RGMII connectivity in a 64-pin SQFN (9x9 mm) package with industrial temperature rating. It integrates a USB 3.1 Gen 1 PHY, a 10/100/1000 Ethernet MAC with RGMII interface to an external PHY, and a 1.8V/3.3V mixed-voltage I/O ring for direct connection to common Ethernet PHYs. A USB-to-Ethernet bridge controller is a category of interface IC that allows a host processor or embedded system lacking native Gigabit Ethernet access to add wired network connectivity through a USB port, typically used where the host has no MII/RGMII-capable MAC or where USB is the only exposed peripheral interface. The product sits in the hierarchy of USB bridge controllers -> network interface controllers -> interface ICs -> integrated circuits, and is commonly deployed as a drop-in network upgrade in designs that need 1 Gbps without redesigning the host platform. Key features of the LAN7801T-I/9JX include USB 3.1 Gen 1 (5 Gbps) SuperSpeed support with backward compatibility to USB 2.0 High-Speed/Full-Speed/Low-Speed, integrated 10/100/1000 MAC, RGMII v1.3 / v2.0 (reduced and core modes) interface to external PHY, jumbo frame support up to 9 KB, Energy-Efficient Ethernet (EEE) per IEEE 802.3az, and industrial -40C to +85C operating range. The part supports CDC-NCM, CDC-ECM, and proprietary Windows/Linux/macOS drivers for plug-and-play integration across operating systems. The device uses a single 25 MHz reference clock (with optional 125 MHz syncE), integrates PHY-side terminations, and provides hardware-offload for checksum, TCP Segmentation Offload, and IEEE 1588 timestamping (depending on driver/firmware revision). Power management includes multiple suspend states (U1/U2 USB, energy detect, magic packet wake), making it suitable for always-on but low-power edge platforms. Typical applications include USB-to-Ethernet dongles and docking stations, industrial PCs and gateways, network printers, NAS enclosures, embedded Linux boards needing GbE, point-of-sale (POS) terminals, automotive infotainment, and ruggedized tablets. The LAN7801T-I/9JX is the industrial-temp (I) variant supplied in Tape & Reel packaging. When designing with this part, pay attention to PCB layout: route the 90-ohm differential USB 3.1 SuperSpeed pairs and RGMII traces with strict length-matching, keep the 25 MHz crystal within 200 mils of XI/XO, and provide a solid ground reference plane beneath the exposed pad for thermal and return-path integrity. This page synthesizes distributor pricing, drop-in alternatives from the Microchip LAN78xx family and cross-brand USB-to-Ethernet bridges, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
LAN8700C-AEZG-AR2 - 10/100 Ethernet PHY | Microchip | Automotive
LAN8700C-AEZG-AR2

LAN8700C-AEZG-AR2 - 10/100 Ethernet PHY | Microchip | Automotive

Microchip Technology LAN8700C-AEZG-AR2 is a low-power 10/100 Mb/s Ethernet physical-layer transceiver with full MII and RMII host interfaces, HP Auto-MDIX support, and variable I/O voltage operation. The device is supplied in a 36-pin QFN package with an exposed pad, measuring 6 mm by 6 mm, for compact embedded Ethernet designs. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts logical data supplied by a host controller into signals suitable for twisted-pair Ethernet cabling. It belongs to the transceiver and interface-IC hierarchy within network semiconductor solutions. This LAN8700 variant is intended for automotive and industrial embedded systems where low-power operation, compact packaging, cable flexibility, and robust transient protection are important design considerations. Key characteristics include support for 10 Mb/s and 100 Mb/s operation, full MII and RMII controller interfaces, HP Auto-MDIX support, and ±15 kV ESD-protected cable-side connections. The variable I/O voltage architecture allows the digital interface voltage to be selected independently of the analog PHY supply, simplifying integration with host processors operating at different logic levels. The automotive AR2 ordering option supports design environments requiring an extended automotive qualification profile. The LAN8700 architecture combines an analog 10/100 Ethernet front end with digital data-path logic and an integrated 1.6 V to 3.6 V low-power core. Its exposed thermal pad provides a direct heat-transfer path from the IC into the PCB. The 6 mm × 6 mm QFN-36 footprint also requires careful escape routing for its MII or RMII signals, clock inputs, power rails, and magnetics-side connections. Typical uses include automotive infotainment controllers, industrial Ethernet gateways, embedded Linux platforms, set-top equipment, and compact communications modules. The MII interface provides a parallel data path for higher host clock rates, while RMII reduces pin count and board-routing pressure in designs where the host controller supports it. Auto-MDIX simplifies installation by allowing the PHY to handle straight-through or crossover cable connections automatically. Designers should follow the manufacturer datasheet for the exposed-pad land pattern, decoupling, magnetic-component selection, cable termination, and separation between analog and digital circuitry. This page combines package, interface, protection, and application information with replacement guidance and engineering-focused design notes to support PCB and firmware implementation.

RFQ Contact
LAN8700C-AEZG-TR - 10/100 Ethernet PHY | Microchip
LAN8700C-AEZG-TR

LAN8700C-AEZG-TR - 10/100 Ethernet PHY | Microchip

The Microchip Technology LAN8700C-AEZG-TR is a 10/100 Ethernet physical-layer transceiver supporting MII and RMII interfaces, HP Auto-MDIX, and ±15 kV ESD protection in a 36-lead 6 x 6 mm QFN package. The device is designed for low-power, industrial-temperature embedded Ethernet systems and accepts variable I/O voltage for flexible host-interface integration. It can also operate from a single 3.3 V supply through an integrated 3.3 V-to-1.8 V linear regulator. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, is the component that converts digital data between a host controller and the physical copper network. It belongs to the network-interface hierarchy: Ethernet transceiver → Ethernet interface IC → integrated circuit. The LAN8700C handles the MII or RMII digital signaling and analog signaling required for 10BASE-T and 100BASE-TX networks, while HP Auto-MDIX simplifies cabling by allowing the PHY to negotiate transmit and receive pairs automatically. Key features include support for both MII and RMII host interfaces, HP Auto-MDIX operation, and ±15 kV ESD protection. The 36-QFN package measures 6 x 6 mm, making the device suitable for compact embedded platforms. Variable I/O voltage helps the PHY interface with a wider range of host logic, while the single-supply option simplifies power planning when only 3.3 V is readily available. The architecture supports a 50 MHz reference-clock arrangement with a permitted tolerance of ±50 ppm and a duty cycle from 40% to 60%. In an RMII design, the host controller supplies the reference clock and handles the parallel data interface. The integrated regulator can then produce the required 1.8 V internal rail from a 3.3 V input. Designers must still observe the recommended capacitor values, layout geometry, clocking, and decoupling arrangements in the manufacturer datasheet. Typical applications include industrial Ethernet controllers, embedded routers, programmable logic controllers, factory automation equipment, motor-control systems, security appliances, and compact network-connected sensors. The MII interface offers broader compatibility with conventional Ethernet controllers, while RMII reduces the number of host-side signals and is often preferred for compact systems with an integrated Ethernet MAC. The main design consideration is PCB implementation. A 36-QFN device has short leads and a compact thermal pad, so accurate footprint alignment, clean ground return paths, short high-frequency connections, and uninterrupted ground-plane continuity are important. Magnetic isolation, RJ45 integration, and ESD protection must be designed according to the applicable Ethernet physical-layer requirements and the manufacturer reference guidance. This product page combines the manufacturer electrical description with package information, focused application guidance, practical layout considerations, and same-footprint alternatives. It is intended to help engineers determine whether the LAN8700C-AEZG-TR fits an existing embedded Ethernet design before requesting a quote or committing the component to a bill of materials.

RFQ Contact
LAN8700IC-AEZG-TR - 10/100 Ethernet PHY | Microchip
LAN8700IC-AEZG-TR

LAN8700IC-AEZG-TR - 10/100 Ethernet PHY | Microchip

The Microchip Technology LAN8700IC-AEZG-TR is a single-channel 10/100 Mbps Ethernet physical-layer transceiver with full MII and RMII support, supplied in a 36-pin QFN package measuring 6 mm by 6 mm. The device operates from a 3.3 V supply, provides ±15 kV ESD-protected network interfaces, and includes HP Auto-MDIX support for automatic crossover handling. Its tape-and-reel ordering code is intended for automated manufacturing and surface-mount assembly. An Ethernet PHY is the physical-layer component that converts digital frame data into electrical signals suitable for a twisted-pair Ethernet cable. It sits below the Ethernet MAC in the protocol hierarchy and above the physical magnetics and connector. The LAN8700 family is categorized as a variable-I/O-voltage analog interface IC for embedded Ethernet systems, with MII and RMII host interfaces allowing integration with microcontrollers, processors, and programmable logic. The principal feature set includes support for both 10 Mbps and 100 Mbps Ethernet operation, full MII and RMII interfaces, HP Auto-MDIX, ±15 kV ESD protection, and flexPWR technology. The variable-I/O arrangement helps accommodate systems in which the PHY communicates with host logic operating at a lower voltage. A 50 MHz reference clock with a tolerance of ±50 ppm and a duty cycle from 40% through 60% provides the timing reference used by the LAN8700/LAN8700i family. From a design perspective, the PHY separates Ethernet medium access from the host processor’s digital bus. MII provides separate controls and parallel data paths, while RMII reduces the number of host-interface signals for compact embedded designs. The network side connects through the external magnetics path required by a conventional 10/100BASE-T Ethernet port, allowing the PHY to remain independent from the connector and transformer implementation. Typical implementations include industrial embedded controllers, networked sensors, building-automation equipment, communications modules, and compact data-acquisition systems. The part is particularly useful when an embedded processor already provides a MII or RMII interface and the design needs standards-based 10/100 Ethernet connectivity without implementing analog Ethernet signaling directly. The primary design consideration is matching the host bus voltage, clock requirements, and digital timing to the selected processor. PCB layout must also preserve the differential characteristics of the transmit and receive pairs, maintain appropriate separation from switching circuitry, and follow the manufacturer’s guidance for the QFN exposed pad and external magnetics network. This page combines interface capabilities, ordering information, application guidance, package details, and replacement analysis to support faster engineering evaluation. It also distinguishes true package-compatible alternatives from related Ethernet products that would require different pinouts, interfaces, or board layouts.

RFQ Contact
LAN8710A-EZC - 10/100 Ethernet PHY | Microchip (Tape & Reel)
LAN8710A-EZC

LAN8710A-EZC - 10/100 Ethernet PHY | Microchip (Tape & Reel)

The Microchip Technology LAN8710A-EZC is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII and RMII MAC connectivity in a 32-QFN package measuring 5 x 5 mm. It supports 10 Mbps and 100 Mbps links, full-duplex operation, auto-negotiation, and HP Auto-MDIX for direct or crossover cables. The device is designed for low-power, small-footprint consumer, industrial, and enterprise networking equipment. An Ethernet PHY is a physical-layer semiconductor that converts digital MAC data into electrical signals suitable for twisted-pair cabling, while receiving and converting incoming cable signals back into digital data. The LAN8710A family belongs to the network-interface hierarchy: Ethernet PHY, physical-layer transceiver, network interface IC, and interface semiconductor. Key features include support for IEEE 802.3u MII and RMII connections, 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, and Microchip flexPWR technology. The supplied manufacturer material identifies both extended-commercial and industrial temperature-range options, although the exact temperature range assigned to this orderable suffix is not explicitly stated in the provided snippets. The package is a 32-QFN surface-mount device. The PHY is intended to work with an Ethernet MAC or a microcontroller containing an appropriate Ethernet MAC interface. MII and RMII provide different clocking and signal arrangements, so the host controller, board traces, and firmware must be matched to the selected interface mode. The verified manufacturer description confirms full-duplex operation and support for both 10 Mbps and 100 Mbps speeds. Typical applications include industrial Ethernet equipment, consumer networking products, embedded systems, IoT gateways, and compact Ethernet-enabled embedded controllers. A design must provide correct decoupling, controlled clocking, a compatible magnetics network path, and PCB layout that follows the manufacturer recommendations. The verified data does not provide the complete pin mapping, electrical limits, or application-specific reference design, so those details should be checked in the manufacturer datasheet before layout release. This page summarizes the verified manufacturer and distributor information while clearly separating confirmed features from electrical values that were not supplied. It is intended to help engineers identify the correct Ethernet PHY, package, interface type, and likely replacement family before consulting the complete datasheet.

RFQ Contact
LAN8710A-EZC-ABC - 10/100 Ethernet PHY | Microchip
LAN8710A-EZC-ABC

LAN8710A-EZC-ABC - 10/100 Ethernet PHY | Microchip

Microchip Technology LAN8710A-EZC-ABC is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver supporting 10 Mbps and 100 Mbps operation, with MII and RMII MAC interfaces, in a 32-pin SQFN package measuring 5 mm by 5 mm. An Ethernet PHY is the physical-layer device that converts digital MAC data into electrical signals suitable for twisted-pair cabling and recovers incoming signals for the Ethernet controller. It belongs to the network-interface hierarchy: Ethernet transceiver > physical-layer transceiver > Ethernet interface IC > semiconductor. The LAN8710A family targets consumer, industrial, and enterprise equipment where a compact 10/100 Ethernet connection is required. Key features include support for both MII and RMII host interfaces, automatic negotiation of speed and duplex mode, and HP Auto-MDIX operation for direct or crossover cable connections. The variable-voltage digital interface allows the PHY to connect with a broad range of MAC hardware. Its 32-SQFN 5 mm by 5 mm package supports compact embedded systems without requiring a large connector or external magnetics beside the PHY itself. The LAN8710A architecture separates the Ethernet medium-access function from the host controller, leaving the MAC and protocol stack to an embedded processor or dedicated network controller. MII provides a wider parallel interface, while RMII reduces the number of digital signals required for designs with constrained pin count. Automatic negotiation allows the link partner and PHY to select the highest mutually supported speed and duplex mode. Typical applications include embedded Linux systems, industrial Ethernet controllers, set-top boxes, printers, game consoles, security equipment, and compact IoT gateways. The 10/100 capability is suitable for management networks and legacy equipment that has not migrated to Gigabit Ethernet. An external Ethernet magnetics module and suitably terminated line-side network path remain required because the PHY does not incorporate the physical cable transformer. Design the PCB around the manufacturer reference schematic, particularly the exposed-pad ground connection, short high-frequency supply routes, and controlled-length digital interfaces. Verify power sequencing, clock requirements, and MII or RMII signal integrity with the MAC controller and cable configuration used in the final system. This product page combines the manufacturer family specifications, verified ordering information, package details, application guidance, and engineering design notes to support component selection, PCB planning, and drop-in replacement evaluation.

RFQ Contact
LAN8710A-EZC-TR - 10/100 Ethernet PHY | Microchip
LAN8710A-EZC-TR

LAN8710A-EZC-TR - 10/100 Ethernet PHY | Microchip

The Microchip Technology LAN8710A-EZC-TR is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII and RMII MAC connectivity in a 32-QFN package measuring 5 x 5 mm. It supports 10 Mbps and 100 Mbps links, full-duplex operation, auto-negotiation, and HP Auto-MDIX for direct or crossover cables. The device is designed for low-power, small-footprint consumer, industrial, and enterprise networking equipment. An Ethernet PHY is a physical-layer semiconductor that converts digital MAC data into electrical signals suitable for twisted-pair cabling, while receiving and converting incoming cable signals back into digital data. The LAN8710A family belongs to the network-interface hierarchy: Ethernet PHY, physical-layer transceiver, network interface IC, and interface semiconductor. Key features include support for IEEE 802.3u MII and RMII connections, 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, and Microchip flexPWR technology. The supplied manufacturer material identifies both extended-commercial and industrial temperature-range options, although the exact temperature range assigned to this orderable suffix is not explicitly stated in the provided snippets. The package is a 32-QFN surface-mount device. The PHY is intended to work with an Ethernet MAC or a microcontroller containing an appropriate Ethernet MAC interface. MII and RMII provide different clocking and signal arrangements, so the host controller, board traces, and firmware must be matched to the selected interface mode. The verified manufacturer description confirms full-duplex operation and support for both 10 Mbps and 100 Mbps speeds. Typical applications include industrial Ethernet equipment, consumer networking products, embedded systems, IoT gateways, and compact Ethernet-enabled embedded controllers. A design must provide correct decoupling, controlled clocking, a compatible magnetics network path, and PCB layout that follows the manufacturer recommendations. The verified data does not provide the complete pin mapping, electrical limits, or application-specific reference design, so those details should be checked in the manufacturer datasheet before layout release. This page summarizes the verified manufacturer and distributor information while clearly separating confirmed features from electrical values that were not supplied. It is intended to help engineers identify the correct Ethernet PHY, package, interface type, and likely replacement family before consulting the complete datasheet.

RFQ Contact
LAN8710A-EZC-TR-ABC - 10/100 Ethernet PHY | Microchip
LAN8710A-EZC-TR-ABC

LAN8710A-EZC-TR-ABC - 10/100 Ethernet PHY | Microchip

The Microchip LAN8710A-EZC-TR-ABC is a low-power 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with a 32-pin VFQFN exposed-pad package. It supports 10 Mbps and 100 Mbps data rates, full-duplex operation, IEEE 802.3u MII, and RMII connections to an Ethernet media-access controller. The device operates from a 1.6 V to 3.6 V supply and is specified for the extended commercial temperature range of 0°C to 85°C. An Ethernet PHY is the physical-layer component that converts digital MAC data into differential signals for a twisted-pair cable, then converts received signals back into digital data. The LAN8710A occupies the PHY layer of the Ethernet hierarchy, above the physical medium and below the MAC layer. Its integrated 10/100 capability allows one Ethernet port design to support both legacy 10 Mbps networks and Fast Ethernet networks operating at 100 Mbps. Microchip LAN8710A devices feature HP Auto-MDIX, which allows a single RJ45 port to work with straight-through or crossover cables. Automatic negotiation selects the best supported speed and duplex mode, while the transceiver also provides full-duplex operation for contemporary switched Ethernet links. These functions simplify installation and reduce the need for manual link configuration in consumer, industrial, and enterprise equipment. The flexPWR technology used in the LAN8710A family supports low-power operation and is intended for compact, energy-conscious designs. The MII interface supports both 10 Mbps and 100 Mbps transfer rates, while RMII reduces the number of MAC interface signals where a reduced-pin architecture is desirable. The exposed thermal pad beneath the 5 mm by 5 mm package provides a direct heat-dissipation path to the PCB copper during continuous data transmission. Typical uses include industrial Ethernet controllers, embedded Linux platforms, network appliances, set-top equipment, printers, IP cameras, and compact communication modules. A MAC such as a Microchip STM32 controller can connect over RMII when its integrated Ethernet MAC supports the required clock and data signaling, while a more complex processor may use the full MII interface. For PCB design, reserve the exposed pad as a thermal and ground connection, follow the manufacturer's recommended magnetics and decoupling network, and keep the high-speed differential pairs short, symmetric, and continuously referenced to the ground plane. Confirm the exact pin functions, strap resistors, reference clock method, and RMII timing configuration in the LAN8710A datasheet before releasing the PCB layout.

RFQ Contact
LAN8710A-EZK - 10/100 Ethernet PHY | Microchip Technology
LAN8710A-EZK

LAN8710A-EZK - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology LAN8710A-EZK is a low-power single-channel Ethernet physical-layer transceiver for 10BASE-T and 100BASE-TX links, with support for 10 Mbps and 100 Mbps operation through a variable-voltage digital MII or RMII interface. The device is housed in a 32-QFN package measuring 5 mm by 5 mm. Its feature set includes HP Auto-MDIX, auto-negotiation, flexPWR technology, full-duplex operation, and industrial-temperature options. An Ethernet PHY, also called an Ethernet physical-layer transceiver, is the interface between a digital Ethernet media-access controller and twisted-pair cabling. It performs signal encoding, line conditioning, auto-negotiation, and crossover handling. The LAN8710A family occupies the physical-layer portion of the Ethernet hierarchy, connecting an Ethernet MAC through MII or RMII while the MAC handles higher-level frame processing. The LAN8710A-EZK supports both 10BASE-T and 100BASE-TX operation. HP Auto-MDIX allows the PHY to work with straight-through or crossover cables, while auto-negotiation selects the best supported speed and duplex mode. The variable I/O voltage allows the digital interface to operate with either 2.5 V or 3.3 V equipment, depending on the system design and selected operating conditions. The flexPWR feature is intended to reduce power consumption in portable and space-constrained systems. Microchip describes the LAN8710A family as a small-footprint, low-power solution for consumer electronics, industrial products, and enterprise equipment. Because the PHY is a digital interface IC rather than a power semiconductor, its operating characteristics are primarily defined by link rate, supply voltage, interface mode, temperature range, package, and power-management behavior. Typical applications include industrial Ethernet equipment, consumer network devices, embedded systems, USB-to-Ethernet adapters, IP cameras, set-top boxes, and communications equipment. The 32-QFN footprint is useful where board area is limited, while MII and RMII support allows the PHY to pair with either a full MII-capable MAC or a reduced pin-count RMII controller. Designers should confirm the exact supply rails, magnetics, crystal or clock requirements, decoupling, and exposed-pad layout against the manufacturer datasheet. The Ethernet magnetics and line-termination network remain essential parts of the physical design even when the PHY itself is highly integrated. Keep the digital interface traces short and isolate the analog network-side connections from noisy switching nodes. This page combines the LAN8710A-EZK datasheet, package and interface details, commercially relevant sourcing questions, same-footprint alternatives, comparison points, and practical PCB guidance. It is intended to help engineers evaluate the PHY before integrating it into a new 10/100 Ethernet design.

RFQ Contact
LAN8710AI-EZK-ABC - Industrial 10/100 Ethernet PHY | Microchip
LAN8710AI-EZK-ABC

LAN8710AI-EZK-ABC - Industrial 10/100 Ethernet PHY | Microchip

The Microchip Technology LAN8710AI-EZK-ABC is an industrial-temperature 10BASE-T/100BASE-TX Ethernet physical layer transceiver with a variable-voltage digital MII or RMII host interface, HP Auto-MDIX support, and a 32-pin QFN 5 x 5 mm package. It provides the physical-layer functions required to connect an Ethernet MAC to a 10/100BASE-T network while supporting automatic speed and duplex negotiation. An Ethernet PHY is a semiconductor within the Ethernet interface hierarchy: an Ethernet controller or MAC communicates through a digital bus, while the PHY translates that data into differential copper-pair signaling. The LAN8710AI family supports IEEE 802.3-2005 operation, vendor-specific registers, MII and RMII host interfaces, and direct or crossover cable connections through HP Auto-MDIX. This makes it suitable for embedded equipment that needs 10/100 Ethernet without a four-pair Gigabit Ethernet physical layer. The principal benefits are its small 32-QFN footprint, flexible MII or RMII connectivity, low-power flexPWR operation, and broad industrial-temperature capability. The AI suffix identifies the industrial option, supporting operation from -40°C to 85°C, while the standard digital host interface can operate with a variable I/O voltage. Auto-negotiation automatically selects the best supported speed and duplex mode, reducing host configuration requirements when connected to either 10BASE-T or 100BASE-TX equipment. Internally, the PHY separates digital MAC signaling from the analog magnetic-link interface. MII provides separate control, status, transmit, and receive paths, while RMII reduces the number of digital signal lines for applications where a compact host interface is preferred. The exposed-pad QFN construction also supports heat transfer into the PCB rather than relying on a conventional lead-frame package. Because the device handles cable-side signal generation, the magnetics and physical layout around the PHY remain critical to link performance. Typical implementations include industrial Ethernet gateways, programmable controllers, embedded servers, automation equipment, smart-building controllers, and network-connected sensor platforms. The LAN8710AI-EZK-ABC is especially relevant where an MCU or dedicated Ethernet controller requires a compact 10/100 PHY, industrial temperature support, and compatibility with both MII and RMII implementations. For PCB design, follow the manufacturer’s pin-description table, exposed-pad land pattern, and recommended magnetic-circuit layout. Place the PHY, magnetics, and high-speed copper pairs close together, provide clean supply and ground connections, and observe the differential trace geometry shown in the application guidance. The key trade-off is that the part supports 10/100BASE-T only, so designs requiring 1000BASE-T operation need a Gigabit Ethernet PHY instead. This page combines manufacturer specifications, industrial-temperature positioning, interface guidance, and same-footprint alternatives to support component selection, schematic review, and PCB implementation.

RFQ Contact
LAN8710AI-EZK-TR - 10/100 Ethernet PHY | Microchip Technology
LAN8710AI-EZK-TR

LAN8710AI-EZK-TR - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology LAN8710AI-EZK-TR is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII and RMII host interfaces, auto-negotiation, HP Auto-MDIX, integrated voltage regulation, and integrated ESD protection. It is packaged in a 32-pin QFN measuring 5 mm by 5 mm and is designed for compact consumer, industrial, and enterprise equipment. An Ethernet PHY is the physical-layer component that translates data between a host digital interface and copper cabling. The LAN8710A family supports 10 Mbps and 100 Mbps links, while MII and RMII connectivity allows it to pair with digital Ethernet controllers or application processors. Within the network hierarchy, the part operates below the Ethernet MAC and above the transformer-coupled 10/100BASE-T cable interface. The device provides auto-negotiation for automatic speed and duplex selection and HP Auto-MDIX support, allowing direct-connect and crossover cables without a manual crossover switch. Its variable I/O voltage supports adaptation to the digital interface voltage, while the integrated regulator and ESD-protection components reduce external component count. The manufacturer identifies the LAN8710A family as a low-power, small-footprint solution for consumer, industrial, and enterprise applications. The LAN8710AI-EZK-TR is part of the LAN8710A/LAN8710Ai family and supports both IEEE 802.3u MII and reduced-pin-count RMII interfaces. These host-side interfaces provide design flexibility for embedded processors, industrial controllers, set-top equipment, printers, network appliances, and other 10/100 Ethernet products. The 5 mm by 5 mm QFN footprint helps limit board area in space-constrained equipment. Typical deployments include industrial automation controllers, network management appliances, embedded Ethernet equipment, printers, consumer-electronics accessories, and communications equipment. For a new design, confirm that the selected processor exposes a compatible MII or RMII interface and verify the required clock, supply, and magnetics requirements against the manufacturer datasheet before schematic release. Layout quality is especially important around a high-speed mixed-signal device. Place the PHY close to the Ethernet connector and network magnetics, keep copper paths short, provide clean return paths, and follow the manufacturer reference layout. Differential-pair geometry, via symmetry, plane continuity, and isolation from noisy switching circuitry directly influence signal integrity and EMC performance. This product summary combines the exact orderable MPN, package information, interface capabilities, family-level features, lifecycle information, and application guidance. It also identifies where application-specific electrical limits must be confirmed in the manufacturer datasheet before schematic and layout signoff.

RFQ Contact
LAN8710AI-EZK-TR-ABC - 10/100 Ethernet PHY | Microchip
LAN8710AI-EZK-TR-ABC

LAN8710AI-EZK-TR-ABC - 10/100 Ethernet PHY | Microchip

Microchip LAN8710AI-EZK-TR-ABC is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 32-SQFN 5x5 mm package, variable I/O voltage, and MII or RMII connectivity to an Ethernet MAC. It supports data rates of 10 Mb/s and 100 Mb/s, automatic speed and duplex negotiation, and HP Auto-MDIX for direct or crossover cable connections. An Ethernet PHY is the physical-layer device that converts logical data from an Ethernet MAC into signals that can traverse a copper cable. The PHY sits below the MAC in the Ethernet hierarchy and directly controls the 10BASE-T or 100BASE-TX physical link. The LAN8710AI-EZK-TR-ABC combines this physical-layer function with flexible digital interfacing, automatic link negotiation, and low-power operation in a compact surface-mount package. Key features include support for both 10 Mb/s and 100 Mb/s Ethernet operation, MII and RMII interfaces, variable digital I/O voltage, HP Auto-MDIX, and automatic speed and duplex negotiation. The industrial-temperature option supports operation from -40°C to 85°C, making the device suitable for industrial controls, embedded systems, communications equipment, and connected products that require a compact 10/100 Ethernet interface. The LAN8710AI family uses Microchip flexPWR technology and is designed for space-constrained, power-sensitive applications. Its MII interface provides parallel digital signaling for implementations requiring broader MAC control, while RMII reduces the number of interface signals for designs seeking a smaller, lower-power connection. The manufacturer documentation identifies IEEE 802.3-2005 compliance and both commercial and industrial temperature variants within the family. Typical applications include industrial Ethernet controllers, embedded Linux platforms, factory automation equipment, serial-to-Ethernet systems, network interface cards, set-top equipment, and embedded network interfaces requiring 10/100BASE-TX connectivity. The small 5x5 mm package also supports compact industrial control boards and connected instrumentation where board area is limited. Designers should preserve the manufacturer's recommended power and decoupling networks, provide an appropriate crystal or clock source, and follow the reference layout in the LAN8710A/LAN8710Ai datasheet. The exposed thermal pad requires suitable ground-plane copper and thermal-via treatment. Magnetic isolation between the PHY and Ethernet cable is normally implemented in the external magnetics and RJ45 interface network. This page combines manufacturer specifications, application guidance, practical PCB considerations, and a parameter-focused comparison with same-package alternatives. It is designed to help engineers determine whether the LAN8710AI-EZK-TR-ABC matches the required Ethernet speed, MAC interface, package, temperature range, and industrial design constraints.

RFQ Contact
LAN8720A-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip
LAN8720A-CP-TR-ABC

LAN8720A-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip

The Microchip Technology LAN8720A-CP-TR-ABC is a single-channel, low-power 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with RMII host connectivity, a 1.6 V to 3.6 V supply range, and a 24-pin SQFN package measuring 4 mm by 4 mm. It operates from 0°C to +85°C and is supplied in tape-and-reel packaging. An Ethernet PHY is the physical-layer interface between a host controller and twisted-pair Ethernet cabling. Within the network hierarchy, the LAN8720A connects an RMII-capable microcontroller, application processor, or dedicated Ethernet controller to a 10/100 network. It implements full-duplex 10BASE-T and 100BASE-TX operation while supporting HP Auto-MDIX, reducing the need to distinguish straight-through and crossover cabling. The device supports standard RMII communication and operates at 10 Mbps or 100 Mbps. Its flexible supply range of 1.6 V to 3.6 V permits integration with 1.8 V, 2.5 V, and 3.3 V systems. The 24-SQFN package provides a compact 4 mm by 4 mm footprint for space-constrained embedded products, while its commercial temperature range covers applications from 0°C to +85°C. Microchip's flexPWR technology is used to reduce power consumption in the LAN8720A family, making the transceiver suitable for connected embedded equipment where energy efficiency is important. The device provides separate digital and analog supply domains, enabling system designers to control supply sequencing and noise isolation according to the manufacturer's application guidance. Typical uses include industrial Ethernet controllers, consumer network equipment, embedded gateways, set-top boxes, printers, IP cameras, and microcontroller-based network nodes. The LAN8720A is especially useful when a host processor already provides an RMII interface and the design needs a compact, low-power 10/100 copper-Ethernet front end. PCB implementation should follow the manufacturer's reference layout for the 24-pin SQFN footprint, exposed pad, magnetics, crystal or clock source, and 50-ohm transmission lines. Care is required with analog and digital supply decoupling, Ethernet transformer isolation, and link-partner startup because those details directly affect EMI, cable compliance, and packet-transfer reliability. This page combines the manufacturer specifications with practical implementation guidance, interface requirements, temperature distinctions, and same-footprint replacement considerations. It is intended to help engineers identify whether the LAN8720A-CP-TR-ABC matches a board's electrical, mechanical, and environmental requirements before layout release or production sourcing.

RFQ Contact
LAN8720AI-CP - 10/100 RMII Ethernet PHY | Microchip
LAN8720AI-CP

LAN8720AI-CP - 10/100 RMII Ethernet PHY | Microchip

The Microchip Technology LAN8720AI-CP is a small-footprint 10BASE-T and 100BASE-TX Ethernet transceiver with an RMII interface, auto-negotiation, and HP Auto-MDIX support. It is supplied in a 24-SQFN package measuring 4 mm by 4 mm and is designed for embedded systems requiring 10/100 Ethernet connectivity with a 50 MHz RMII MAC interface. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between digital MAC signals and analog signals carried over twisted-pair cabling. The LAN8720AI-CP occupies the PHY level within the Ethernet hierarchy, working alongside an Ethernet MAC rather than replacing it. Its RMII connection reduces the number of parallel data lines required between the PHY and the host controller. The device supports 10BASE-T and 100BASE-TX operation through automatic speed and duplex negotiation. HP Auto-MDIX allows direct-connect or crossover LAN cables without manual cable selection. It also supports IEEE 802.3-2005 compliant register functions as well as vendor-specific register functions, giving embedded software both standardized and device-specific configuration options. Microchip identifies the LAN8720A and LAN8720Ai as compact solutions with up to 40% lower power consumption than earlier Microchip transceivers. The family integrates a voltage regulator and ESD-protection components to help reduce bill-of-material requirements. The LAN8720AI-CP connects to an Ethernet MAC through a standard RMII interface and supports both 10 Mbps and 100 Mbps operation. Typical uses include industrial Ethernet controllers, embedded Linux systems, programmable logic controllers, factory automation equipment, IoT gateways, and compact network adapters. The small 4 mm by 4 mm package also makes the device suitable for space-constrained boards where a conventional magnetics-heavy Ethernet implementation would be difficult to place. When designing around the LAN8720AI-CP, verify the RMII signal mapping, clock requirements, supply sequencing, magnetics selection, and Ethernet magnetics implementation against the manufacturer datasheet. Layout should keep the digital RMII interface away from the analog magnetics and provide a controlled return path beneath the high-speed differential pairs. Use the manufacturer pin-description table when assigning PCB tracks. This page combines device identity, package details, interface capabilities, replacement guidance, application engineering notes, and side-by-side alternatives. It is intended to help engineers locate the correct datasheet, assess board compatibility, select companion components, and determine whether a proposed replacement is genuinely pin-compatible rather than merely functionally similar.

RFQ Contact
LAN8720AI-CP-ABC - 10/100 Ethernet PHY | Microchip
LAN8720AI-CP-ABC

LAN8720AI-CP-ABC - 10/100 Ethernet PHY | Microchip

The Microchip Technology LAN8720AI-CP-ABC is a compact 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with a standard RMII interface, operating at 10 Mbps or 100 Mbps. It is offered in a 24-SQFN package measuring 4 x 4 mm and supports the industrial temperature range of -40°C to 85°C. The device uses Microchip flexPWR technology and supports HP Auto-MDIX for direct or crossover cable connections. An Ethernet PHY is the physical-layer component that translates digital data from an Ethernet media-access controller into signals that can traverse a twisted-pair network. In the hierarchy of network semiconductors, the PHY operates below the Ethernet MAC and above the transformer, magnetics, connector, and cable. The RMII interface reduces the number of signals required between the PHY and the host controller, making the LAN8720AI-CP-ABC suitable for compact embedded systems with limited connector and routing resources. Key features include full-duplex 10BASE-T and 100BASE-TX operation, automatic speed and duplex negotiation, HP Auto-MDIX support, and operation from 1.8 V, 2.5 V, or 3.3 V supplies. IEEE 802.3-2005-compliant register functions are supported alongside vendor-specific registers. These features allow the PHY to connect to an RMII-based microcontroller or dedicated Ethernet controller without requiring a separate manual speed configuration. The LAN8720AI-CP-ABC integrates the digital transceiver, analog transmit and receive channels, clock recovery, and auto-negotiation functions into one package. Its 24-SQFN footprint supports high-density PCB layouts, while the exposed thermal pad provides a direct heat-transfer path. The interface is designed for host systems operating at 50 MHz RMII reference-clock frequency, which simplifies synchronization with common embedded Ethernet media-access controllers. Typical applications include industrial Ethernet controllers, embedded IoT gateways, factory automation equipment, network-connected sensors, compact embedded Linux systems, and consumer or communications equipment with a 10/100 Ethernet link. The PHY is particularly useful when the design requires wired networking but must limit board area, interface pin count, and power consumption compared with a larger Ethernet transceiver implementation. Layout quality is critical because high-speed digital and analog signals share the same package. Place the PHY close to the Ethernet magnetics and connector, keep the RMII clock and data traces short, provide clean supply decoupling, and follow the manufacturer’s reference layout for the exposed pad and mixed-signal return paths. This page combines package and interface guidance with practical replacement analysis for design reviews and sourcing. The manufacturer identifies the LAN8720A family as active and distinguishes extended-commercial and industrial temperature options. For new designs, confirm the exact ordering code, package, thermal grade, and RMII implementation against the current manufacturer datasheet before releasing production artwork.

RFQ Contact
LAN8720AI-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip
LAN8720AI-CP-TR-ABC

LAN8720AI-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip

The Microchip LAN8720AI-CP-TR-ABC is a compact 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with Full MII and RMII host interfaces, 24-SQFN lead-free packaging in a 4 x 4 mm footprint, and an industrial temperature range of -40°C to +85°C. The device is designed to connect a microcontroller, processor, or other embedded host to a standard 10/100 Ethernet network. An Ethernet PHY is the physical-layer component that converts digital frame data into differential Ethernet signaling and receives differential network signals for conversion back into digital data. The LAN8720AI belongs to the Ethernet transceiver hierarchy and the broader integrated-circuit category of network interface ICs. Its RMII interface reduces the number of host signals required for 10/100 Ethernet connectivity, while Full MII support provides an alternative host interface for designs using the wider parallel bus. Key features include automatic speed and duplex negotiation, HP Auto-MDIX support, IEEE 802.3-2005 compliant and vendor-specific register functions, and Microchip flexPWR technology. Auto-negotiation automatically establishes the best supported speed and duplex mode. HP Auto-MDIX allows direct-connect or crossover Ethernet cables without a manual crossover switch, simplifying connections to computers, switches, and test equipment. The LAN8720AI family operates from 1.8 V, 2.5 V, or 3.3 V supply levels, allowing integration with both 3.3 V and compatible lower-voltage embedded systems. The industrial-order option supports -40°C to +85°C operation, while the related commercial option supports 0°C to +85°C. The 24-SQFN package includes an exposed thermal pad and is supplied on a 4,000-piece reel for the listed ordering configuration. Typical applications include industrial Ethernet controllers, embedded Linux systems, factory automation equipment, serial-to-Ethernet gateways, IoT gateways, and compact network appliances. In each case, the PHY supplies the physical Ethernet connection while the host controller handles higher-layer networking, packet processing, and application protocols. RMII is especially useful where connector count and PCB area are constrained. Designers should follow the manufacturer datasheet for the complete pin-description table, recommended crystal and decoupling circuits, RMII timing requirements, and exposed-pad land pattern. Validate the PHY and host clocking arrangement, magnetics, termination, and cable path as a complete Ethernet interface rather than evaluating the transceiver independently of its external network components. This page consolidates the manufacturer interface capabilities, package and temperature distinctions, order-code behavior, and practical replacement guidance into an engineering-focused comparison of the LAN8720AI-CP-TR-ABC and compatible Ethernet PHY options.

RFQ Contact
LAN8740A-EN - 10/100 Ethernet PHY | Microchip Technology
LAN8740A-EN

LAN8740A-EN - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology LAN8740A-EN is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 32-pin SQFN package measuring 5 mm by 5 mm. It supports MII and RMII host interfaces, operates at 10 Mbps or 100 Mbps, and includes variable I/O voltage, auto-negotiation, HP Auto-MDIX, cable diagnostics, and deterministic loopback delay. An Ethernet PHY is the physical-layer interface between a network media-access controller and twisted-pair cabling. Within the Ethernet interface hierarchy, the PHY connects a digital MAC to the analog 10BASE-T or 100BASE-TX line interface. The LAN8740A supports IEEE 802.3, IEEE 802.3u, and IEEE 802.3az Energy Efficient Ethernet operation, placing it in the low-power 10/100 Ethernet transceiver category. Key features include support for both straight-through and crossover cables through HP Auto-MDIX, automatic speed and duplex-mode selection, variable I/O voltage, and cable diagnostics that can reduce installation and troubleshooting costs. Commercial and industrial temperature variants are offered because the LAN8740A/LAN8740Ai family is specified from 0°C to 70°C or -40°C to 85°C, depending on the selected ordering option. The device is designed for embedded systems requiring a compact 10/100 Ethernet interface rather than gigabit data rates. MII support offers a parallel host interface for designs using the larger pin assignment, while RMII reduces the number of host-side signals and can simplify connections to controllers that support that interface. Auto-negotiation allows the PHY to select the best supported speed and duplex combination with the link partner. Typical uses include industrial controllers, embedded network equipment, set-top and communications appliances, and connected industrial products requiring a compact Ethernet front end. A 5 mm by 5 mm surface-mount package supports compact board layouts, but correct magnetics, termination, reference-clock implementation, decoupling, and high-speed layout remain essential for reliable links. Designers should follow the manufacturer datasheet and its reference circuit for the 25 MHz crystal or oscillator network, magnetic isolation, center-tap capacitors, and PCB layout. The 5 mm by 5 mm package also requires careful thermal assessment when the PHY operates continuously in an enclosed system. This page consolidates manufacturer specifications, distributor availability information, package details, and verified cross-reference evidence into an engineering-oriented guide. It also distinguishes documented functions from parameters that still require confirmation from the complete manufacturer datasheet or a detailed PCB design review.

RFQ Contact
LAN8740AI-EN - 10/100 Ethernet PHY, RMII/MII, 32-SQFN | Microchip
LAN8740AI-EN

LAN8740AI-EN - 10/100 Ethernet PHY, RMII/MII, 32-SQFN | Microchip

The Microchip LAN8740AI-EN is a single-port 10/100 Base-T Ethernet physical layer (PHY) transceiver with MII and RMII host interfaces, offered in the 32-pin SQFN (5x5 mm) package and rated for the industrial -40 °C to +85 °C temperature range. The 'AI' suffix denotes the industrial temperature grade, while '-EN' identifies the standard tray/tube ordering code of the LAN8740Ai family. An Ethernet PHY is the physical-layer transceiver that converts parallel digital data from a MAC into differential 10BASE-T or 100BASE-TX signalling on a twisted-pair cable, and converts the incoming analogue signal back into digital words. In the OSI hierarchy a PHY sits below the MAC inside the data-link layer, and the device therefore belongs to the network interface controller family of integrated circuits alongside MAC controllers and USB-to-Ethernet bridges. Key features include auto-negotiation for automatic speed and duplex selection, HP Auto-MDIX for direct-connect or crossover cable use without manual crossover wiring, auto-polarity correction, deterministic loopback delay for real-time system performance, and cable diagnostics that reduce installation and service cost. The device is compliant with IEEE 802.3 and IEEE 802.3u and is well suited to consumer, embedded and industrial equipment. The LAN8740Ai also carries Microchip's flexPWR technology, an integrated low-power design approach that removes the need for an external switching regulator for the PHY core. This reduces board area, component count and overall system power, which is decisive in battery-backed and Energy Efficient Ethernet designs where the PHY is frequently the largest standby consumer on the board. Typical uses include industrial Ethernet gateways, PLC and HMI panels, IP cameras and NVRs, set-top boxes and consumer set-top equipment, printer and copier controllers, embedded Linux boards using an RMII-capable SoC, and network-connected sensors and IoT nodes. The small 5x5 mm footprint keeps the PHY compact enough for space-constrained embedded boards while the 32-pin SQFN keeps the pin count manageable for four-layer PCB design. The main design trade-off is interface choice: RMII reduces the host pin count to a minimum and therefore lowers EMI and cost, but it is sensitive to clock timing and requires a stable 50 MHz reference, whereas full MII offers a parallel, more forgiving bus at the expense of roughly thirty signal pins. Commercial designs should confirm RMII clock, reference and crystal/oscillator requirements against the manufacturer datasheet before layout is frozen. This page consolidates the manufacturer device documentation, verified distributor listings, drop-in alternatives and practical PCB and layout guidance into a single design reference, so that schematic and layout decisions for a LAN8740Ai-based Ethernet port can be made without assembling the same information from many sources.

RFQ Contact
LAN8741AI-EN - 10/100 Ethernet PHY | Microchip Technology
LAN8741AI-EN

LAN8741AI-EN - 10/100 Ethernet PHY | Microchip Technology

Microchip Technology LAN8741AI-EN is a 10/100 Base-T/TX Fast Ethernet physical-layer transceiver with a Full MII or RMII MAC interface, operating at 10 Mbps or 100 Mbps. The device is housed in a 32-SQFN package measuring 5 mm by 5 mm and supports industrial-temperature operation from -40°C to 85°C. Its primary interfaces are MII, RMII, 10BASE-T, and 100BASE-TX. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between digital MAC signals and analog signals carried over twisted-pair cabling. Within the network hierarchy, LAN8741AI-EN belongs to the Ethernet interface IC category and implements the physical layer required by a 10/100 Fast Ethernet MAC. It adds negotiated speed and duplex selection, HP Auto-MDIX cable handling, Energy Efficient Ethernet support, and power-saving sleep functions to the basic physical-layer function. The LAN8741AI-EN supports IEEE 802.3az Energy Efficient Ethernet, full-duplex 10BASE-T and 100BASE-TX links, automatic speed and duplex negotiation, and HP Auto-MDIX. HP Auto-MDIX allows a direct-connect or crossover cable to be used without manually reconfiguring the PHY. The manufacturer also identifies deterministic loopback delay as a feature for real-time system performance, making the device relevant to deterministic embedded networking designs. Communication with the Ethernet MAC is performed through standard MII or RMII interfaces. IEEE 802.3u-compatible MII operation provides a parallel digital interface, while RMII reduces the number of required signals. The interface choice allows the PHY to be paired with an embedded controller, microcontroller, application processor, or other MAC-capable host according to the system clocking and signal-count requirements. Typical uses include industrial control equipment, embedded Ethernet gateways, factory automation nodes, building automation controllers, network-connected sensors, and compact communication modules. The industrial temperature range supports designs expected to operate across extended commercial environments, although system designers must also verify thermal, isolation, magnetics, and regulatory requirements for their installation environment. PCB implementation should account for the 5 mm by 5 mm SQFN footprint, exposed-pad thermal management, short high-speed traces, controlled return paths, and the external magnetics required by the Ethernet physical layer. Keep the digital MAC interface separated as far as practical from the analog network-side circuitry, and use the manufacturer’s reference layout and component guidance to preserve signal integrity and reliable auto-negotiation. This product page organizes the LAN8741AI-EN’s interface capabilities, package information, operating ranges, available drop-in alternative, application guidance, and design considerations. It also identifies the engineering details that require confirmation against the manufacturer datasheet, particularly pin assignments and detailed electrical limits.

RFQ Contact
LAN8742-CZ - 100Mbps Ethernet PHY with 24-QFN
LAN8742-CZ

LAN8742-CZ - 100Mbps Ethernet PHY with 24-QFN

The Microchip Technology LAN8742-CZ is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 100 Mbps maximum link rate, variable I/O voltage, and a 24-pin QFN package. It supports the IEEE 802.3 and IEEE 802.3u standards and is designed to connect an Ethernet MAC through an RMII interface to copper twisted-pair Ethernet magnetics. The verified search data identifies it as an Ethernet controller interface device and a 1/1 driver-receiver configuration with full-duplex RMII support. An Ethernet PHY is the physical-layer device that translates digital MAC data into electrical signaling for a network cable and converts received cable signals back into digital data. In the hierarchy, the LAN8742-CZ belongs to the Ethernet transceiver, network-interface, integrated-interface-IC, and broader semiconductor categories. Placing a PHY between a host controller and an RJ45 magnetics assembly allows a microcontroller, application processor, or dedicated Ethernet controller to connect to 10 Mbps or 100 Mbps copper networks without implementing the analog cable interface directly. Verified features include 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, Energy Efficient Ethernet support identified in the family description, and Wake-On-LAN functionality identified for the LAN8742 family. The variable I/O voltage allows the digital interface voltage to be selected for integration with a host, while the compact 24-QFN, 4 x 4 mm package supports space-constrained embedded designs. The verified results also describe cable diagnostics support, although detailed diagnostic limits are not supplied. The LAN8742-CZ is normally used as the PHY beside a 10/100 Ethernet magnetic module and RJ45 connector. RMII connects the PHY to the MAC, reducing the number of parallel data and control signals compared with older MII implementations. The PHY supports 10 Mbps and 100 Mbps operation and automatically negotiates the best supported speed and duplex mode, simplifying host-side configuration. Exact timing, current, voltage-range, temperature, and package-dimension details require the manufacturer datasheet and are not inferred here. For new production designs, verify lifecycle status and sourcing before committing to an obsolete device. The verified cross-reference data specifically identifies LAN8742A-CZ-TR as a compatible substitute with extended availability, while also describing LAN8742AI-CZ-TR as a direct pin-compatible replacement. Any substitution should be checked against the exact RMII pin mapping, voltage domains, package exposed-pad requirements, magnetic-device pinout, and system timing. This page combines verified distributor and manufacturer information with application guidance, replacement context, and package-focused design notes. It does not invent unpublished pricing, electrical limits, pin names, or lifecycle dates; unavailable values are explicitly marked for engineering review.

RFQ Contact
LAN8742-CZ-TR - 100Mbps Ethernet PHY with 24-QFN (Tape & Reel)
LAN8742-CZ-TR

LAN8742-CZ-TR - 100Mbps Ethernet PHY with 24-QFN (Tape & Reel)

The Microchip Technology LAN8742-CZ-TR is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 100 Mbps maximum link rate, variable I/O voltage, and a 24-pin QFN package. It supports the IEEE 802.3 and IEEE 802.3u standards and is designed to connect an Ethernet MAC through an RMII interface to copper twisted-pair Ethernet magnetics. The verified search data identifies it as an Ethernet controller interface device and a 1/1 driver-receiver configuration with full-duplex RMII support. An Ethernet PHY is the physical-layer device that translates digital MAC data into electrical signaling for a network cable and converts received cable signals back into digital data. In the hierarchy, the LAN8742-CZ-TR belongs to the Ethernet transceiver, network-interface, integrated-interface-IC, and broader semiconductor categories. Placing a PHY between a host controller and an RJ45 magnetics assembly allows a microcontroller, application processor, or dedicated Ethernet controller to connect to 10 Mbps or 100 Mbps copper networks without implementing the analog cable interface directly. Verified features include 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, Energy Efficient Ethernet support identified in the family description, and Wake-On-LAN functionality identified for the LAN8742 family. The variable I/O voltage allows the digital interface voltage to be selected for integration with a host, while the compact 24-QFN, 4 x 4 mm package supports space-constrained embedded designs. The verified results also describe cable diagnostics support, although detailed diagnostic limits are not supplied. The LAN8742-CZ-TR is normally used as the PHY beside a 10/100 Ethernet magnetic module and RJ45 connector. RMII connects the PHY to the MAC, reducing the number of parallel data and control signals compared with older MII implementations. The PHY supports 10 Mbps and 100 Mbps operation and automatically negotiates the best supported speed and duplex mode, simplifying host-side configuration. Exact timing, current, voltage-range, temperature, and package-dimension details require the manufacturer datasheet and are not inferred here. For new production designs, verify lifecycle status and sourcing before committing to an obsolete device. The verified cross-reference data specifically identifies LAN8742A-CZ-TR as a compatible substitute with extended availability, while also describing LAN8742AI-CZ-TR as a direct pin-compatible replacement. Any substitution should be checked against the exact RMII pin mapping, voltage domains, package exposed-pad requirements, magnetic-device pinout, and system timing. This page combines verified distributor and manufacturer information with application guidance, replacement context, and package-focused design notes. It does not invent unpublished pricing, electrical limits, pin names, or lifecycle dates; unavailable values are explicitly marked for engineering review.

RFQ Contact
LAN8742A-CZ - 10/100 Ethernet PHY, RMII, 24-SQFN | Microchip (Tape & Reel)
LAN8742A-CZ

LAN8742A-CZ - 10/100 Ethernet PHY, RMII, 24-SQFN | Microchip (Tape & Reel)

The Microchip LAN8742A-CZ is a low-power 10BASE-T/100BASE-TX Ethernet PHY transceiver with variable I/O voltage, packaged in a 24-pin SQFN (4x4 mm) and supplied on tape and reel. It supports MII and RMII MAC interfaces, operates from a 1.8V to 3.3V variable I/O supply, and is IEEE 802.3 / 802.3u compliant. The device integrates auto-negotiation, auto-polarity correction, and HP Auto-MDIX, eliminating the need for crossover cables. It is well-suited for consumer, embedded, and industrial Ethernet applications. A PHY (physical layer transceiver) is a key element of any Ethernet link: it sits between the MAC controller and the magnetic transformer/RJ-45, handling line encoding/decoding, link training, and electrical signaling over twisted-pair copper. PHY transceivers are part of the broader category of Ethernet interface ICs, which include MAC controllers, switches, and integrated MAC+PHY SoCs. The LAN8742A specifically implements the 10/100 Mbps copper PHY only; higher-speed Gigabit (1000BASE-T) PHYs use multi-level signaling (PAM) and more pins. Key features of the LAN8742A-CZ include Wake-On-LAN support for system-level sleep modes, cable diagnostics for fault detection, and flexPWR flexible power technology for low-power operation. The variable I/O voltage (1.8V-3.3V) allows direct connection to low-voltage MCUs without level shifters. The HP Auto-MDIX feature automatically detects and compensates for TX/RX pair swaps, allowing either straight-through or crossover cables to be used interchangeably. Architecturally, the LAN8742A employs DSP-based echo and crosstalk cancellation to achieve robust 100BASE-TX performance over Cat5 cable. The on-chip PHY includes an integrated termination network and uses energy detect plus power-down modes to meet modern standby-power requirements. MII and RMII MAC interfaces are selectable via strap pins, allowing the same part to be paired with virtually any MCU or SoC MAC. Typical applications include IoT gateways, industrial Ethernet nodes, embedded web servers, building automation controllers, IP cameras, and consumer electronics requiring a wired network connection. The wide 1.8V-3.3V I/O range and low power consumption also make it attractive for battery-powered Ethernet-enabled devices. When designing with the LAN8742A-CZ, follow the Microchip LAN8742 QFN Routing Checklist for proper PCB layout - the analog ground plane and 50-ohm impedance-controlled differential pairs are critical for radiated emissions and signal integrity compliance. Decoupling capacitors must be placed adjacent to each power pin, and the magnetics must be specified to IEEE 802.3 isolation and return-loss specifications. This page synthesizes distributor pricing, drop-in same-BLAN alternatives, and Microchip application-note design notes not found in the manufacturer datasheet alone - giving engineers a single, decision-ready reference.

USD $0.74 In Stock