LAN8710AI-EZK-ABC - Industrial 10/100 Ethernet PHY | Microchip
MPN: LAN8710AI-EZK-ABC ✓ ActiveLAN8710AI-EZK-ABC Overview
An Ethernet PHY is a semiconductor within the Ethernet interface hierarchy: an Ethernet controller or MAC communicates through a digital bus, while the PHY translates that data into differential copper-pair signaling. The LAN8710AI family supports IEEE 802.3-2005 operation, vendor-specific registers, MII and RMII host interfaces, and direct or crossover cable connections through HP Auto-MDIX. This makes it suitable for embedded equipment that needs 10/100 Ethernet without a four-pair Gigabit Ethernet physical layer.
The principal benefits are its small 32-QFN footprint, flexible MII or RMII connectivity, low-power flexPWR operation, and broad industrial-temperature capability. The AI suffix identifies the industrial option, supporting operation from -40°C to 85°C, while the standard digital host interface can operate with a variable I/O voltage. Auto-negotiation automatically selects the best supported speed and duplex mode, reducing host configuration requirements when connected to either 10BASE-T or 100BASE-TX equipment.
Internally, the PHY separates digital MAC signaling from the analog magnetic-link interface. MII provides separate control, status, transmit, and receive paths, while RMII reduces the number of digital signal lines for applications where a compact host interface is preferred. The exposed-pad QFN construction also supports heat transfer into the PCB rather than relying on a conventional lead-frame package. Because the device handles cable-side signal generation, the magnetics and physical layout around the PHY remain critical to link performance.
Typical implementations include industrial Ethernet gateways, programmable controllers, embedded servers, automation equipment, smart-building controllers, and network-connected sensor platforms. The LAN8710AI-EZK-ABC is especially relevant where an MCU or dedicated Ethernet controller requires a compact 10/100 PHY, industrial temperature support, and compatibility with both MII and RMII implementations.
For PCB design, follow the manufacturer’s pin-description table, exposed-pad land pattern, and recommended magnetic-circuit layout. Place the PHY, magnetics, and high-speed copper pairs close together, provide clean supply and ground connections, and observe the differential trace geometry shown in the application guidance. The key trade-off is that the part supports 10/100BASE-T only, so designs requiring 1000BASE-T operation need a Gigabit Ethernet PHY instead.
This page combines manufacturer specifications, industrial-temperature positioning, interface guidance, and same-footprint alternatives to support component selection, schematic review, and PCB implementation.
Drop-in alternatives for LAN8710AI-EZK-ABC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LAN8710AI-EZK-ABC (same form factor and footprint) — differing in Package, Power Technology, RoHS Status, Host Interface, MAC Interface.
LAN8710AI-EZK
✅ Drop-In📋 Reference alternative (not in catalog)
LAN8710AI-EZK-TR-ABC
✅ Drop-InContact for price
View Datasheet →LAN8710A-EZK
✅ Drop-InContact for price
View Datasheet →LAN8710A-EZC-ABC
✅ Drop-InContact for price
View Datasheet →LAN8710A-EZC-TR-ABC
✅ Drop-InContact for price
View Datasheet →LAN8710AI-EZK-ABC Specifications
| Ethernet Support | 10BASE-T and 100BASE-TX |
| Maximum Ethernet Data Rate | 100 Mbit/s |
| Host Interface | MII or RMII digital interface |
| MAC Interface Logic Voltage | Variable I/O voltage |
| Cable Polarity Support | HP Auto-MDIX |
| Speed and Duplex | Automatic negotiation |
| Standards Compliance | IEEE 802.3-2005 |
| Power Technology | flexPWR technology |
| Industrial Temperature Range | -40°C to 85°C |
| Package | 32-QFN, 5 x 5 mm |
| Package Height | 0.9 mm maximum |
| Mounting Type | Surface mount |
| Number of Pins | 32 pins |
| Ethernet Magnetics Requirement | External magnetic components required |
| Digital Register Support | IEEE 802.3-2005 compliant and vendor-specific registers |
| RoHS Status | Compliant |
| REACH Status | Compliant |
LAN8710AI-EZK-ABC 0.9 mm maximum Pin Configuration Guide
Pin configuration for LAN8710AI-EZK-ABC (0.9 mm maximum package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for LAN8710AI-EZK-ABC.
Refer to the datasheet for full pin configuration.
Typical Applications
LAN8710AI-EZK-ABC is suitable for 6 applications: Industrial Ethernet Gateway, Programmable Automation Controller, Smart Building Controller, Embedded Network Appliance, Connected Sensor Platform, Embedded Server or Control Console.
Industrial Ethernet Gateway
The LAN8710AI-EZK-ABC fits an industrial gateway that connects a host controller to a 10/100BASE-T network. Its MII and RMII interfaces let the designer select the digital bus appropriate for the host processor, while HP Auto-MDIX removes crossover-cable restrictions in field installations. The -40°C to 85°C range supports equipment exposed to temperature variation outside consumer enclosures. Place the PHY and external magnetics close to the Ethernet connector, preserve controlled differential-pair geometry, and provide local decoupling at the supply pins to maintain reliable link performance.
Recommended
Programmable Automation Controller
The LAN8710AI-EZK-ABC can provide network connectivity for a programmable automation controller while leaving control and motion functions to the host MCU. Automatic speed and duplex negotiation allows the controller to operate with both 10BASE-T and 100BASE-TX infrastructure without manual link configuration. The industrial temperature rating is valuable in machinery rooms where ambient conditions can exceed the 0°C lower limit of commercial options. The principal design consideration is maintaining separation between sensitive PHY supply, digital interface, and magnetics paths to reduce coupling into control signals.
Recommended
Smart Building Controller
A smart-building controller can use the LAN8710AI-EZK-ABC to communicate over a 10/100 Ethernet backbone while operating sensors, relays, and local user interfaces. MII support accommodates controllers using wider parallel host buses, whereas RMII reduces connector count in compact designs. HP Auto-MDIX lets installers use straight-through or crossover wiring, simplifying field commissioning. Because building equipment may sit in unheated cabinets, the -40°C lower operating limit provides useful margin. Firmware should still handle link renegotiation, and the PCB should follow the manufacturer’s magnetic-component placement guidance.
Recommended
Embedded Network Appliance
The LAN8710AI-EZK-ABC is useful in compact network appliances that require 10/100 Ethernet but do not need Gigabit throughput. Its 5 x 5 mm QFN package conserves board area, and the choice between MII and RMII supports both legacy parallel-interface hosts and more pin-constrained processors. Automatic negotiation improves interoperability with switches and embedded network equipment operating at 10 or 100 Mbit/s. Designers should reserve solid copper area under the exposed pad, follow the recommended component and magnetic-circuit layout, and validate signal integrity across the full operating-temperature range.
Recommended
Connected Sensor Platform
The LAN8710AI-EZK-ABC can add wired Ethernet connectivity to a distributed sensor platform that monitors environmental or equipment data. A 100 Mbit/s link provides sufficient bandwidth for typical telemetry, configuration, and status traffic, while low-power flexPWR technology supports compact embedded equipment. The industrial temperature range makes the device suitable for installations outside controlled office environments. Keep the PHY and magnetics away from high-current switching nodes, observe differential impedance requirements, and verify recovered-clock and power-supply behavior in the final board-level design.
Recommended
Embedded Server or Control Console
The LAN8710AI-EZK-ABC can provide a cost-effective 10/100 network port for an embedded server, maintenance console, or diagnostic controller. A dedicated Ethernet controller can use MII for a conventional parallel interface, while an MCU-based implementation can use RMII to reduce host I/O requirements. HP Auto-MDIX improves installation flexibility and automatic negotiation accommodates common 10/100 infrastructure. Because this PHY does not support 1000BASE-T, systems requiring higher transfer rates should use a Gigabit-capable controller and PHY instead. Thermal performance should be checked with the final exposed-pad and copper implementation.
Recommended
Recommended Products Summary
Engineering reference data for LAN8710AI-EZK-ABC — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LAN8710AI-EZK | LAN8710AI-EZK-TR-ABC | LAN8710A-EZK | LAN8710A-EZC-ABC | LAN8710A-EZC-TR-ABC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-QFN (5x5) | 32-QFN (5x5) - same | 32-QFN (5x5) - same | 32-QFN (5x5) - same | 32-QFN (5x5) - same | 32-QFN (5x5) - same |
| Ethernet Speed Support | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX | 10BASE-T and 100BASE-TX |
| Maximum Link Rate | 100 Mbit/s | 100 Mbit/s | 100 Mbit/s | 100 Mbit/s | 100 Mbit/s | 100 Mbit/s |
| Host Interface | MII or RMII | MII or RMII | MII or RMII | MII or RMII | MII or RMII | MII or RMII |
| Auto-MDIX | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported |
| Temperature Range | -40°C to 85°C | -40°C to 85°C | -40°C to 85°C | 0°C to 85°C | 0°C to 85°C | 0°C to 85°C |
| Power Technology | flexPWR | flexPWR | flexPWR | flexPWR | flexPWR | flexPWR |
| IEEE 802.3-2005 Support | Supported | Supported | Supported | Supported | Supported | Supported |
Key Differentiators
- Lower operating-temperature limit (vs LAN8710A-EZK)
- Industrial temperature option in the same 32-QFN footprint (vs LAN8710A-EZC-ABC)
- Compact Ethernet interface supporting two host-bus styles (vs LAN8710A-EZK)
- Exact industrial ordering option (vs LAN8710AI-EZK-TR-ABC)
Design Notes
Implement the 32-QFN footprint directly from the manufacturer package drawing, including the exposed thermal pad and its solder-mask and paste details. Place the PHY close to the board edge or Ethernet connector when practical, shorten the differential traces to the magnetics, and avoid splitting the return path beneath the pairs. The copper plane under the exposed pad should be evaluated thermally and for return-current continuity rather than added only for mechanical attachment.
Follow the manufacturer’s recommended Ethernet magnetic-component arrangement to control insertion loss, impedance, and radiated emissions. Keep the PHY-to-magnetics differential pair short and symmetric, use the specified impedance-controlled geometry, and keep unrelated switching nodes and noisy clocks away from this region. Do not route copper or split planes beneath the differential pairs if doing so creates a discontinuity in their reference path.
Provide the specified core and digital I/O supplies close to the device and decouple each supply domain according to the manufacturer application circuit. The digital interface voltage is variable, so the host bus voltage must match the selected I/O configuration. Confirm supply sequencing, voltage tolerance, and power-up behavior in the complete system; the adjustable interface capability does not remove the need to verify every supply rail independently.
Do not treat the LAN8710AI-EZK-ABC as a Gigabit Ethernet PHY: it supports 10BASE-T and 100BASE-TX, not 1000BASE-T. Also distinguish AI industrial parts from A commercial parts when substituting order codes. The AI suffix supports -40°C to 85°C, while the standard A option starts at 0°C, making an apparently identical 32-QFN replacement unsuitable for sub-zero environments.
Compliance Information
RoHS and REACH compliance are identified in the cited comparison information. No explicit AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated for this order code.