Products (44,000+)

LM2900DR - Quad Norton Operational Amplifier | Texas Instruments (Tape & Reel)
LM2900DR

LM2900DR - Quad Norton Operational Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments LM2900DR is a quad, high-gain, frequency-compensated Norton operational amplifier in a 14-pin SOIC (D) package. The device contains four independent amplifier sections designed for single-supply or split-supply operation over a wide supply-voltage range. Its Norton input stage provides low input bias current, while the internally compensated architecture simplifies gain-stage implementation in general-purpose signal conditioning. The LM2900DR is identified by the verified distributor listing as a standard general-purpose amplifier with four circuits in a 14-SOIC package. A Norton operational amplifier is a current-buffer input operational-amplifier architecture. It differs from the more common voltage-input differential pair by using a translinear input stage that offers low input bias current and good performance with high-impedance sources. This places the LM2900DR in the operational-amplifier hierarchy: operational amplifier, amplifier IC, analog IC, and semiconductor. The part is intended for general-purpose analog signal conditioning rather than precision instrumentation or automotive-qualified systems. According to the Texas Instruments LM2900 product page, the LM2900 family consists of four independent, high-gain frequency-compensated Norton operational amplifiers designed to operate from a single supply over a wide range of voltages. The product description also identifies large output-voltage swing, output short-circuit protection, internal frequency compensation, and low input bias current as important characteristics. These features make the device suitable for buffering, voltage amplification, signal conditioning, and general feedback-control circuits. The LM2900DR can be used with a single positive supply or with split supplies. In single-supply designs, the input and output signal levels must remain within the amplifier's common-mode and output-swing limits. The LM2900 family is internally frequency compensated, so the feedback network establishes the closed-loop gain without requiring a separate compensation capacitor in ordinary applications. The 14-pin SOIC package provides a conventional surface-mount footprint and a practical temperature range for industrial and consumer equipment. Typical uses include transducer-signal conditioning, sensor interfaces, audio preamplification, low-current feedback amplifiers, and general analog control loops. Because the verified data does not provide detailed electrical limits, bandwidth, noise, slew rate, or exact input/output range, those parameters should be confirmed in the manufacturer datasheet before final design release. The verified distributor listings show current purchasing channels, but they do not provide a reliable standardized price table in the supplied data. This page combines the verified manufacturer and distributor identity for LM2900DR with package information, sourcing links, comparison structure, and practical selection guidance. It is intended to help engineers identify the correct 14-SOIC Norton amplifier while avoiding unsupported parameter assumptions. Confirm the latest ordering information, electrical limits, lead time, and lifecycle status with Texas Instruments or an authorized distributor before production commitment.

RFQ Contact
LM2900N - Quad 2.5MHz Norton Operational Amplifier | TI
LM2900N

LM2900N - Quad 2.5MHz Norton Operational Amplifier | TI

The Texas Instruments LM2900N is a quad, high-gain, frequency-compensated Norton operational amplifier with four independent amplifiers in a 14-pin PDIP package. Its headline specifications include a 2.5 MHz gain-bandwidth product, 20 V/µs slew rate, 4.5 V to 32 V single-supply operation, and ±2.2 V to ±16 V dual-supply operation. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2900 belongs to the Norton-operational-amplifier family, characterized by current-feedback-style input stages. Within the broader electronics hierarchy, it is an analog amplifier IC, then an operational amplifier, then a general-purpose quad amplifier. The LM2900 provides four independent amplifiers, wide bandwidth, large output-voltage swing, short-circuit protection, internal frequency compensation, and low input-bias current. Internal compensation removes the need for external compensation components in ordinary closed-loop operation, simplifying analog boards that need several amplified signals on one supply rail. Its specified 4.5 V to 32 V single-supply range makes it applicable to legacy industrial control, instrumentation, sensor interfaces, audio, and communications equipment. The 20 V/µs slew rate supports faster edge rates than many general-purpose amplifier selections, while the 2.5 MHz bandwidth gives useful signal bandwidth for audio and control applications. The DIP package also supports through-hole assembly and socketed prototypes. When designing around the LM2900N, verify input and output common-mode limits at the selected supply voltage. Account for the input-bias current when driving high-impedance sensors, and use stable feedback networks with resistive isolation where required by the source impedance. The device uses four independent amplifiers, but shared-package power and ground connections still require careful layout. This product record combines the verified Texas Instruments family description, distributor package information, ordering details, and cross-reference findings. It also distinguishes electrically similar ordering variants from verified pin-compatible replacements and identifies application guidance that is not presented as a manufacturer reference design.

RFQ Contact
LM2900NE4 - Quad Norton Op Amp, 2.5 MHz | Texas Instruments
LM2900NE4

LM2900NE4 - Quad Norton Op Amp, 2.5 MHz | Texas Instruments

The Texas Instruments LM2900NE4 is a quad, high-gain, frequency-compensated Norton operational amplifier packaged in a 14-pin PDIP. It contains four independent amplifier sections in one package and is designed for general-purpose analog signal conditioning. The device operates from single or split supplies and supports a wide range of supply voltages, with a listed operating range up to 15 V. Its 2.5 MHz gain-bandwidth product and 20 V/µs slew rate provide useful bandwidth for low-frequency instrumentation, signal conditioning, filtering, and general analog processing. The LM2900NE4 uses the Norton current-feedback operational-amplifier architecture. Unlike a conventional voltage-feedback amplifier, the Norton topology is based on low-input-resistance current feedback and is well suited to applications where the source impedance and feedback network are compatible with that operating principle. Internal frequency compensation makes the amplifier convenient to use without external compensation components in closed-loop gain configurations specified by the manufacturer. Key specifications include four amplifier circuits, a 2.5 MHz gain-bandwidth product, a 20 V/µs slew rate, and a 14-pin PDIP package. The device also provides wide supply-voltage operation, large output-voltage swing, output short-circuit protection, and low input-bias-current characteristics according to the LM2900 family information. These features make the LM2900NE4 suitable for industrial control, sensor interfaces, audio and communication signal paths, and test equipment. The quad package can reduce board area when four similar analog functions are required. Each amplifier is independent, allowing the same device to implement four separate gain, buffering, comparison, or filtering functions. The PDIP format is also convenient for through-hole assembly, prototyping, repair, and applications where a large thermal pad is not required. When designing around the LM2900NE4, verify the source impedance and feedback values against the manufacturer’s recommended operating conditions. Because the Norton architecture has different input and feedback considerations from a voltage-feedback op amp, do not substitute a conventional amplifier without checking stability, slew behavior, output swing, and bias-current requirements. Maintain adequate supply decoupling and observe the specified common-mode and output-voltage limits. This product page combines the manufacturer family information, distributor package and availability references, technical comparisons, and practical design guidance to support component selection and replacement planning for the LM2900NE4.

RFQ Contact
LM2900NG4 Quad Norton Op Amp | 14-PDIP | Texas Instruments
LM2900NG4

LM2900NG4 Quad Norton Op Amp | 14-PDIP | Texas Instruments

Texas Instruments LM2900NG4 is a quad, high-gain, frequency-compensated Norton operational amplifier integrated circuit in a 14-pin PDIP package. It contains four independent amplifier sections designed for general-purpose signal amplification, buffering, instrumentation, and other linear analog applications. The device is identified as a standard general-purpose amplifier with a DIP-14 package and is suitable for single-supply operation across a wide voltage range, with split-supply operation also possible. A Norton operational amplifier is a current-buffer amplifier architecture rather than a conventional voltage-input amplifier. Its input signal is represented as a current, which allows the amplifier to operate with relatively low input bias current and can be useful in sensor interfaces, current-feedback signal paths, and feedback networks. The LM2900 family combines four amplifiers in one package, reducing board area and simplifying multi-channel analog designs where several similar signal-processing stages are required. The principal application features are its quad amplifier organization, high gain, internal frequency compensation, and single-supply capability. Frequency compensation allows each amplifier to be used as a stable gain stage without requiring an external compensation network in many standard closed-loop configurations. The wide operating supply range supports industrial, instrumentation, audio, control, and embedded analog systems where the supply voltage is not tightly constrained. The LM2900NG4 uses a 14-pin PDIP package with through-hole mounting. Through-hole construction is useful for prototypes, educational platforms, legacy control boards, industrial equipment, and repair applications where a socket or conventional PCB drilling process is preferred. The DIP-14 footprint also provides generous spacing between leads, simplifying hand assembly and inspection compared with fine-pitch surface-mount packages. When designing around the LM2900NG4, identify the function of each amplifier section and confirm the complete pin assignment, supply requirements, input and output common-mode limits, output swing, and stability behavior in the manufacturer datasheet. Use the manufacturer datasheet for the exact pinout and application examples. Feedback resistors and compensation choices should be calculated for the intended closed-loop gain, while input and output signal paths should be kept short to reduce noise pickup and instability risk. This product page organizes the LM2900NG4 technical profile, sourcing information, package details, practical design notes, and a comparison framework for engineers evaluating quad general-purpose op amps. It is intended to support component selection, schematic review, PCB compatibility checks, and replacement planning rather than replace the complete manufacturer datasheet.

RFQ Contact
LM2901D - 30V Quad Differential Comparator | Texas Instruments
LM2901D

LM2901D - 30V Quad Differential Comparator | Texas Instruments

The Texas Instruments LM2901D is a 30 V quad differential comparator containing four independent open-collector comparator channels in a 14-pin SOIC package. Each channel supports single or split-supply operation, while the device is designed for level detection, low-level sensing, memory, consumer, automotive, and industrial applications. The LM2901D combines a typical input bias current of 25 nA with a typical input offset current of ±5 nA. A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level result indicating which input is higher. Within the semiconductor hierarchy, the LM2901D is a voltage comparator, a linear signal-conditioning IC commonly grouped with amplifier and interface functions. Its open-collector outputs require an external pull-up resistor, allowing several outputs to be wired together when the resulting wired-AND behavior is appropriate for the system. The four independent channels make the LM2901D useful where several sensing decisions must be made in one package. Its open-collector output structure can drive TTL, CMOS, MOS, DTL, and ECL-compatible logic as identified in the manufacturer literature. The specified 300 ns response time supports general-purpose detection rather than the latency demanded by high-speed timing applications. Split-supply operation also permits bipolar sensing around a zero-volt reference. The input stage emphasizes low bias current, which reduces disturbance of high-impedance sensor outputs. A typical 25 nA input bias current is suitable for many threshold and level-detection circuits, while the typical ±5 nA input offset current helps minimize imbalance between the differential inputs. These characteristics should be considered together with input common-mode limits, output pull-up requirements, and supply-voltage tolerances during design verification. Typical uses include monitoring battery or power rails, detecting overvoltage and undervoltage conditions, comparing sensor thresholds, implementing window comparators, and providing four-channel status indication. Because all four outputs are open collector, a pull-up resistor is normally required on each channel. Connecting multiple open-collector outputs to one pull-up can reduce the number of logic signals, but it also creates a shared fault domain and requires careful analysis of output leakage and pull-up current. A practical design must preserve adequate input common-mode headroom at both supply rails, keep differential input voltage within the absolute maximum limits, and select pull-up resistors for the voltage and sink-current requirements of the connected logic. Decoupling capacitors should be placed close to the supply pins, while unused comparator inputs should be tied to a defined potential rather than left floating. This page organizes the key LM2901D electrical characteristics, manufacturer-backed comparison options, pin-package constraints, and application guidance for engineers evaluating a 14-pin quad comparator. It also highlights the practical trade-offs involved when selecting a drop-in alternative with different input offset, bias current, temperature range, or propagation timing.

RFQ Contact
LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments
LM2901DE4

LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments

The Texas Instruments LM2901DE4 is a quad differential comparator with open-collector outputs, designed for single-supply operation from 2 V to 30 V or split-supply operation within the stated common-mode limits. The device contains four independent comparator channels in a 14-pin SOIC package, with a typical input offset voltage of 0.37 mV and an input bias current of 3.5 nA. Each channel can compare two input voltages and provide a logic-level indication through an open-collector output. The LM2901DE4 is suitable for industrial control, sensor interfacing, threshold detection, voltage monitoring, and general-purpose signal conditioning applications. Its low supply current of approximately 200 uA per comparator and wide operating temperature range of -40 °C to +125 °C make it practical for both commercial and extended-temperature equipment. The open-collector outputs allow wired-AND operation and require an external pull-up resistor when the output must drive a logic high. A differential comparator is an analog integrated circuit that compares two voltage inputs and changes its output state according to their relative voltage. The LM2901 belongs to the comparator category within the broader interface IC hierarchy, where analog front-end decision-making is followed by digital logic, control, or measurement. Unlike an operational amplifier, the comparator is intended primarily for threshold crossing and does not provide linear amplification. The LM2901 family combines four channels in one package, allowing a compact design when multiple independent decisions are needed. Its common-mode input range includes ground, making it useful in systems powered from a single positive rail where the signal being compared can approach 0 V. Key features include a maximum supply rating of 38 V, a low input offset voltage of 0.37 mV, an input bias current of 3.5 nA, and low supply-current consumption of approximately 200 uA per comparator. The open-collector output structure is compatible with TTL, MOS, and CMOS logic when the appropriate pull-up is used. The comparator also supports a faster response time than many older standard quad comparators. Because all four channels share the same supply pins, the device is most appropriate when the compared signals operate within the same supply system. The 14-SOIC package provides a conventional surface-mount footprint and broad compatibility with industrial control-board layouts. The internal architecture uses four differential comparator channels referenced to the common ground and supply rails. The input stage is designed for low offset and low bias current, reducing errors when small signal differences must be detected. The open-collector transistor remains off when the comparator output is high impedance and conducts when the output is driven low. The external pull-up resistor determines the high-state voltage and limits the current through the output transistor. The maximum differential input voltage and common-mode voltage limits must be respected during startup, fault conditions, and signal transients. The manufacturer datasheet is the authoritative source for absolute maximum ratings, electrical limits, timing characteristics, and the complete pin configuration. Typical uses include monitoring a battery or power rail, detecting an overvoltage or undervoltage condition, comparing a thermistor or divider output with a reference, and providing a fault flag in industrial equipment. The four channels can also implement independent window comparisons when suitable resistor networks are used. Open-collector outputs are particularly useful when multiple comparators must signal one system event through a common pull-up node. In motor-control, power-supply, and instrumentation circuits, the device can provide a hardware threshold decision before a controller reacts, reducing the processing burden on the controller. The principal design consideration is the pull-up network on every open-collector output. Select the resistor to balance rise time against output-transistor dissipation and required logic current. Keep comparator inputs away from noisy power-switching nodes, use a stable reference for precision thresholds, and account for input common-mode limits. When replacing another quad comparator, verify the complete pinout, output architecture, supply range, input offset, response time, and temperature rating before production use. The LM2901DE4 is a standard general-purpose choice for designs requiring four channels, wide supply tolerance, and flexible open-collector interfacing.

RFQ Contact
LM2901DG - Quad Comparator, 3-36 V, 14-SOIC | onsemi
LM2901DG

LM2901DG - Quad Comparator, 3-36 V, 14-SOIC | onsemi

The onsemi LM2901DG is a single-supply quad differential comparator with four general-purpose channels, a 3 V to 36 V supply range, open-collector CMOS/TTL-compatible outputs, and a 14-pin SOIC package. Each channel offers a typical response time of 1.3 us, making the device suitable for level detection, low-level sensing, and memory applications. The package supports both single and split-supply operation. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four independent channels can evaluate separate thresholds, monitor multiple control signals, or implement sensing functions where a logic-compatible indication is preferable to a continuously amplified analog output. Key features include a wide 3 V to 36 V single-supply operating range, dual-supply operation from ±1.5 V to ±18 V, and open-collector outputs compatible with CMOS and TTL. The maximum input bias current is 0.25 uA at 5 V, while typical low-level specifications include 25 nA input bias current, ±5 nA input offset current, and 130 mV low-output saturation voltage at 4 mA. These characteristics make the device appropriate for low-current threshold-detection circuits. The four comparators share a common supply arrangement but operate independently, allowing separate reference and signal inputs for each channel. Open-collector outputs require an external pull-up resistor and can be wired for wired-AND behavior. The LM2901DG is identified as a CMOS, open-collector, TTL-compatible device, making it suitable for interfacing with both older TTL logic and CMOS control systems. Response time remains short enough for supervisory, sequencing, and discrete threshold applications. Typical uses include industrial control-system threshold detection, automotive sensing interfaces, consumer equipment level supervision, and memory-device address or control comparisons. The 3 V minimum supply also permits operation from regulated 5 V rails, while the 36 V maximum supports higher-voltage industrial systems when suitable input protection is applied. Each open-collector output can directly drive a pull-up-connected digital input or relay driver stage. For robust PCB design, place the pull-up resistor close to the output and maintain short, stable traces for sensitive threshold inputs. Account for input offset voltage when the decision point is critical, and prevent unused comparator inputs from floating. Confirm absolute maximum input and output ratings against the system rails before applying signals near the supply limits. This page combines the LM2901DG operating envelope, drop-in comparison data, pin and package guidance, and application-oriented design notes. It also distinguishes the device from electrically similar quad comparators so engineers can assess supply range, output architecture, common-mode behavior, and timing before replacing an existing part.

RFQ Contact
LM2901DR2 - Quad Open-Collector Comparator | onsemi
LM2901DR2

LM2901DR2 - Quad Open-Collector Comparator | onsemi

onsemi LM2901DR2 is a quad differential voltage comparator with four independent channels, an operating supply range of 3 V to 36 V, and a 14-pin SOIC package. Its open-collector outputs support level detection and interface to compatible logic systems, while its typical input bias current of 25 nA suits low-level sensing applications. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901DR2 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Each of its four channels can operate independently, allowing multiple thresholds, window-detection functions, or simple control decisions to be implemented within one device. The principal features include four comparator channels, a 3 V to 36 V supply range, open-collector outputs, and a typical input bias current of 25 nA. Open-collector outputs provide flexibility when the output must be pulled up to a local supply rail or connected to wired logic. They are not intended to source output current directly, so an external pull-up resistor is normally required. The LM2901DR2 can operate from a single supply or from split supplies, which makes it adaptable to industrial, automotive, and consumer signal-conditioning circuits. Its differential input arrangement allows one input to act as the reference and the other as the sensed signal. Because this is an analog comparator rather than a logic gate, designers should account for input offset voltage, common-mode range, propagation delay, output pull-up requirements, and supply decoupling when defining switching thresholds. Typical uses include battery threshold detection, sensor-limit switching, window comparators, level translation, relay or LED drive, automotive interface circuits, and industrial control inputs. A four-channel implementation can also reduce component count when several independent sensing points must be monitored in the same circuit. When laying out a design, place the bypass capacitor close to the supply pin and route comparator inputs away from switching nodes and high-current paths. Select the pull-up resistor for the required sink current and switching speed, and verify that every input remains inside the device's common-mode range across temperature and supply tolerance. The manufacturer datasheet pin description should be used when assigning PCB tracks. This product page combines the manufacturer-level electrical characteristics, confirmed SOIC-14 alternatives, sourcing guidance, application analysis, and practical PCB considerations needed to evaluate the LM2901DR2 before incorporating it into a new design.

RFQ Contact
LM2901M - 4-Channel 36V Open-Collector Comparator | Texas Instruments
LM2901M

LM2901M - 4-Channel 36V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2901M is a four-channel differential analog comparator with an operating supply range of 2 V to 36 V, a typical response time of 1.3 µs, and open-collector outputs in a 14-pin SOIC package. Designed for single-supply operation, it can also operate from dual supplies providing approximately ±1 V to ±18 V. Each comparator compares two input voltages and produces a digital result that can drive TTL, MOS, or CMOS-compatible logic. The package is identified by the M suffix and is suitable for conventional through-hole PCB assembly when surface-mount assembly is not required. An analog comparator is a semiconductor that converts the relationship between two voltages into a logic-level output. The LM2901 belongs to the comparator hierarchy, where a general-purpose comparator is used for threshold detection, signal conditioning, and industrial control rather than precision analog amplification. Its wide supply range, low input bias current, and low typical supply-current consumption make it suitable for systems operating from low-voltage control circuits through higher-voltage industrial environments. The principal features include four independent comparator channels, an approximate 36 V maximum supply, 800 µA typical supply-current drain, 25 nA typical input bias current, and open-collector outputs suitable for wired logic. These characteristics allow the device to monitor slow and fast control signals while maintaining low loading on high-impedance sensor nodes. The open-collector architecture also supports wired-AND behavior when multiple comparators share a pull-up resistor, although the common output node requires careful voltage and timing analysis. Each internal comparator has an inverting input, a non-inverting input, and an open-collector output. The open-collector transistor normally remains off, so an external pull-up resistor is required to establish a high output state. When the comparator output is pulled low, the output transistor sinks current from that pull-up network. The resulting interface can support wired logic, relay-driver stages, lamp indicators, and other systems where a pulled-up bus must be shared safely. Typical applications include industrial sensor-limit detection, overvoltage and undervoltage monitoring, battery threshold detection, control-system interlock circuits, and logic-level translation around higher-voltage signals. The four channels can be used independently, or several channels can implement window comparison, fault detection, and redundant monitoring functions. A common ground and supply arrangement simplifies multi-channel designs while requiring attention to common-mode limits, output pull-up placement, and input protection. The principal design consideration is ensuring that input and output conditions remain within the comparator's absolute maximum and common-mode limits. Input protection may be required when external wiring exposes the device to transients or voltages outside the normal operating range. The open-collector outputs also need suitable pull-up resistors, with resistance selected from the required sink-current, rise-time, and bus-loading constraints rather than from resistance alone. This page combines manufacturer specifications, verified distributor information, pin-level implementation guidance, and same-footprint replacement analysis. It also identifies the practical trade-offs among closely related LM2901-family ordering options so that engineers can distinguish electrical compatibility, package identity, and qualification differences before committing a design to production.

RFQ Contact
LM2901M96 - 30V Quad Differential Comparator | Harris
LM2901M96

LM2901M96 - 30V Quad Differential Comparator | Harris

The Harris LM2901M96 is a low-power quad differential voltage comparator designed for general-purpose signal conditioning and logic-interface applications. It contains four independent comparison channels in a 14-pin SOIC package and operates from a single or dual supply, with a common-mode input voltage range that includes ground. The device is identified by the manufacturer as a 30-V quad differential comparator, making it suitable for industrial control, sensor interface, and low-voltage logic applications. A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital-level output indicating their relationship. The LM2901M96 belongs to the comparator, analog IC, and semiconductor hierarchy. Its four independent channels allow one package to implement multiple threshold decisions, monitoring functions, or logic decisions. Open-collector outputs are compatible with TTL, CMOS, MOS, DTL, and ECL logic families, enabling the device to operate as an interface between analog sensing circuits and digital logic. Key features include low power consumption, a common-mode input range extending to ground, and open-collector output structure. The common-mode capability is important for single-supply designs in which the sensed signal can approach the lower supply rail. The open-collector outputs can also be pulled up to an appropriate supply voltage and used to drive multiple open-collector-compatible loads when the current and speed requirements are satisfied. The LM2901M96 is a quad comparator rather than a precision instrumentation amplifier or a dedicated logic gate. Each channel compares its non-inverting and inverting inputs independently, allowing the device to serve as a window comparator, overvoltage detector, or simple signal translator. The M96 designation identifies the Harris packaging variant listed in a 14-SOIC configuration. Its exact electrical limits, offset voltage, response time, input bias current, and output-current ratings should be confirmed in the manufacturer datasheet before production release. Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, automotive or equipment control systems, switching power-supply fault detection, and general-purpose logic level conditioning. The comparator is particularly useful when a small analog signal must be converted into a stable digital decision before being processed by a microcontroller or logic gate. For reliable implementation, maintain adequate input common-mode headroom, respect the maximum supply and differential-input ratings, and provide pull-up resistors on each open-collector output. Check output timing against the propagation delay and the required system response time. This page combines manufacturer-family information, package details, sourcing guidance, compatible drop-in options, and practical design considerations for engineers evaluating the LM2901M96.

RFQ Contact
LM2901MWA Quad Open-Collector Comparator | Texas Instruments
LM2901MWA

LM2901MWA Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2901MWA is a four-function differential analog comparator offered in wafer-sale form for industrial-temperature applications. It combines a maximum input offset voltage of 7000 uV, a response time of 1300 ns, a maximum supply current of 2 mA, and an operating temperature range of -40°C to +85°C. The device provides open-collector outputs suitable for TTL, MOS, and CMOS interfacing. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level indication of their relative relationship. The LM2901 belongs to the comparator hierarchy within analog signal conditioning and power-management electronics. Its four independent channels make it suitable when several sensing or threshold decisions must be performed in one package. The common-mode input range includes ground, while differential input voltage can reach the maximum-rated supply voltage of ±38 V. The principal features support robust threshold detection and low-level sensing. Open-collector outputs allow the output state to be established with an external pull-up resistor, which provides flexibility for interfacing to mixed logic families and for wired-AND arrangements. The 7000 uV maximum offset specification defines the worst-case input-voltage difference that can affect switching behavior, while the 1300 ns response time establishes the nominal propagation performance of the comparator. Each of the four comparator channels is independent, allowing separate sensing tasks within a single die. The industrial temperature rating supports equipment operating across a broad ambient range, and the 2 mA maximum supply current suits low-power signal-conditioning systems. The LM2901 family is commonly used for level detection, low-level sensing, and memory-related control functions, where a voltage threshold must be translated into a digital state. Typical uses include industrial sensor interfaces, overvoltage and undervoltage detection, battery threshold monitoring, window comparators, and control logic for power systems. Because the output is open collector, the designer can select the pull-up voltage and resistor to match the receiving logic rather than relying on a fixed active-high or active-low output arrangement. LM2901MWA is supplied as an unpackaged die rather than a conventional leaded or surface-mount package. Board-level implementation therefore requires wafer handling, die attachment, bonding, encapsulation, and qualification of the assembled product. Its absence from the package library and the lack of a public package pin numbering are important constraints when planning assembly or comparing it with packaged LM2901 devices. This page combines the LM2901MWA ordering characteristics, functional limits, comparator specifications, interface considerations, and procurement guidance with a separate evaluation of true drop-in alternatives. Because the target is a wafer-sale die, only an equivalent offered in the same physical form can qualify as a drop-in replacement; standard SOIC or DIP implementations are electrically related but are not interchangeable on a PCB.

RFQ Contact
LM2901N - Quad Open-Collector Comparator | Texas Instruments
LM2901N

LM2901N - Quad Open-Collector Comparator | Texas Instruments

Texas Instruments LM2901N is a general-purpose quad differential comparator containing four independent comparator channels in a 14-pin through-hole DIP package. Each channel compares two input voltages and provides an open-collector output that can pull a logic node low or be released to a pull-up resistor. The device operates from a single supply or from split supplies, with a wide supply-voltage range extending to approximately 36 V. A comparator is a differential amplifier used to evaluate the relationship between two voltages. When the non-inverting input exceeds the inverting input, the associated output transistor turns on; reversing the inputs reverses the output state. The LM2901N belongs to the comparator hierarchy, which includes differential comparator ICs, analog interface ICs, and broader semiconductor signal-conditioning devices. Its four independent channels make it useful when a design requires multiple threshold, level, or sensing decisions. Important characteristics include a typical input bias current of 25 nA, typical input offset current of ±5.0 nA, and low supply-current consumption. The open-collector architecture is especially useful for wired logic, relay-driving interfaces, and systems that share a pull-up rail. Unlike a push-pull output, an open-collector output requires an external pull-up resistor and can safely combine multiple driver nodes when the device ratings and pull-up design are appropriate. The four channels share supply and ground pins but have independent inputs and outputs. This arrangement supports simultaneous comparisons, window detection, and complementary decision logic. Because the outputs are open collector, external pull-up resistors determine the high-state voltage and can be tied to TTL-, CMOS-, or MOS-compatible logic levels. The input arrangement permits sensing signals referenced to ground while the supply rail provides the comparator's operating voltage. Typical applications include industrial level detection, low-level sensing, consumer and automotive threshold decisions, memory and window-comparison circuits, and general-purpose control logic. The LM2901N is particularly appropriate when the design needs several channels, a wide supply range, low input bias current, and flexible output pull-up rather than rail-to-rail push-pull outputs. It is also useful in systems where output transistors must remain off until a wired-AND condition is satisfied. A key design consideration is the pull-up network. Select its resistance to balance rise time, output-sink current, power consumption, and the number of outputs connected to one node. Also route the four differential input pairs away from noisy supply and switching-current paths, because comparator input offset can determine the actual switching threshold. Confirm output-state behavior, input common-mode limits, and supply sequencing against the manufacturer datasheet before finalizing the circuit. This product page combines manufacturer information, distributor listings, package details, and practical comparator design guidance. It also identifies same-package alternatives and organizes the technical trade-offs for engineers comparing the LM2901N with other quad differential comparators before making a PCB-compatible sourcing decision.

RFQ Contact
LM2901N/PB - Quad Open-Collector Comparator | Texas Instruments (Lead-Free (Pb-Free))
LM2901N/PB

LM2901N/PB - Quad Open-Collector Comparator | Texas Instruments (Lead-Free (Pb-Free))

Texas Instruments LM2901N/PB is a general-purpose quad differential comparator containing four independent comparator channels in a 14-pin through-hole DIP package. Each channel compares two input voltages and provides an open-collector output that can pull a logic node low or be released to a pull-up resistor. The device operates from a single supply or from split supplies, with a wide supply-voltage range extending to approximately 36 V. A comparator is a differential amplifier used to evaluate the relationship between two voltages. When the non-inverting input exceeds the inverting input, the associated output transistor turns on; reversing the inputs reverses the output state. The LM2901N/PB belongs to the comparator hierarchy, which includes differential comparator ICs, analog interface ICs, and broader semiconductor signal-conditioning devices. Its four independent channels make it useful when a design requires multiple threshold, level, or sensing decisions. Important characteristics include a typical input bias current of 25 nA, typical input offset current of ±5.0 nA, and low supply-current consumption. The open-collector architecture is especially useful for wired logic, relay-driving interfaces, and systems that share a pull-up rail. Unlike a push-pull output, an open-collector output requires an external pull-up resistor and can safely combine multiple driver nodes when the device ratings and pull-up design are appropriate. The four channels share supply and ground pins but have independent inputs and outputs. This arrangement supports simultaneous comparisons, window detection, and complementary decision logic. Because the outputs are open collector, external pull-up resistors determine the high-state voltage and can be tied to TTL-, CMOS-, or MOS-compatible logic levels. The input arrangement permits sensing signals referenced to ground while the supply rail provides the comparator's operating voltage. Typical applications include industrial level detection, low-level sensing, consumer and automotive threshold decisions, memory and window-comparison circuits, and general-purpose control logic. The LM2901N/PB is particularly appropriate when the design needs several channels, a wide supply range, low input bias current, and flexible output pull-up rather than rail-to-rail push-pull outputs. It is also useful in systems where output transistors must remain off until a wired-AND condition is satisfied. A key design consideration is the pull-up network. Select its resistance to balance rise time, output-sink current, power consumption, and the number of outputs connected to one node. Also route the four differential input pairs away from noisy supply and switching-current paths, because comparator input offset can determine the actual switching threshold. Confirm output-state behavior, input common-mode limits, and supply sequencing against the manufacturer datasheet before finalizing the circuit. This product page combines manufacturer information, distributor listings, package details, and practical comparator design guidance. It also identifies same-package alternatives and organizes the technical trade-offs for engineers comparing the LM2901N/PB with other quad differential comparators before making a PCB-compatible sourcing decision.

RFQ Contact
LM2901NG - 3-36 V Quad Comparator for Level Detection | onsemi
LM2901NG

LM2901NG - 3-36 V Quad Comparator for Level Detection | onsemi

The onsemi LM2901NG is a single-supply quad differential comparator with a 3 V to 36 V operating range, four open-collector outputs, and a 14-pin PDIP package. It is designed for level detection, low-level sensing, and memory applications, with an operating temperature range of -40°C to 105°C. Each of the four independent channels compares an inverting input with a non-inverting input and supports TTL, CMOS, and open-collector interfacing. A quad comparator is a multi-channel analog semiconductor that decides whether one input voltage is above or below another reference voltage. The LM2901NG belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used to produce a digital, logic-level decision from two analog voltages. Its four independent channels allow a compact circuit to monitor several thresholds, levels, or memory-control signals without requiring four separate comparator packages. The principal features include a 3 V to 36 V supply range, single-supply operation, and a low output saturation voltage of 130 mV at 4 mA. The common-mode input range includes ground, making the device practical for single-supply systems in which signals remain near the lower rail. ESD input clamps improve reliability without changing normal comparator operation, while the open-collector outputs permit wired logic, pull-up resistor selection, and compatibility with multiple logic families. Within the LM2901 family, the NG suffix identifies the onsemi 14-pin PDIP configuration. The device provides four separate comparator channels rather than a single comparison function, reducing package count when several independent decisions are required. Its open-collector outputs require an external pull-up when the output must rise to a defined positive voltage. Designers should account for the pull-up value, output leakage, input bias current, and propagation delay when driving long interconnects or switching high-capacitance nodes. Typical applications include industrial sensor threshold detection, battery-powered equipment, memory-control logic, window or level comparators, and general-purpose TTL or CMOS interfacing. Because the operating range extends to 36 V, the LM2901NG can be used in higher-voltage industrial systems when every input remains inside its permitted common-mode range. The -40°C to 105°C temperature range supports both commercial and extended industrial environments. For reliable operation, use the pin-description table and typical application information in the onsemi datasheet when assigning input polarities and output pull-ups. Keep sensitive analog input traces away from high-current switching nodes, provide a stable local supply connection, and select a pull-up resistor that balances rise time against output-driver loading. Input and output filtering may be required when the comparator is used near switching regulators or fast digital signals. This product page combines the manufacturer specifications with package, application, comparison, and design guidance for engineers evaluating LM2901NG. It also identifies qualified same-package alternatives and highlights the electrical and application trade-offs that should be checked before a replacement is approved for an existing PCB.

RFQ Contact
LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments
LM2901NG4

LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2901NG4 is a four-channel general-purpose differential comparator with open-collector outputs, single-supply operation from 2 V to 30 V, and a 14-PDIP package. Each of the four independent channels compares two input voltages and provides a logic-level indication of their relationship. The open-collector architecture allows the outputs to be pulled up to a suitable logic voltage and enables wired-AND operation when multiple channels share an output node. A comparator is an analog integrated circuit that converts the relationship between two voltages into a binary result. The LM2901 belongs to the voltage-comparator hierarchy within the broader amplifier and comparator IC family. Its four independent channels make it useful when a system needs several threshold, level, or crossing-point decisions without using four separate single comparator packages. The LM2901NG4 supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V. According to the manufacturer product page, its outputs are compatible with TTL, MOS, and CMOS logic. The wide supply range allows the same device to be used in low-voltage control circuits and higher-voltage industrial interfaces, provided each input and output node remains within its applicable voltage limits. Each comparator channel is electrically independent, allowing four separate threshold decisions within one package. The open-collector output requires an external pull-up resistor to establish a valid high output state. This arrangement provides flexible interface-voltage selection and can improve system fault tolerance because a wired output can be pulled down by more than one channel. The device does not actively drive the output high. Typical applications include industrial control and threshold detection, instrumentation signal conditioning, sensor-interface decisions, level translation, and general analog signal processing. The four-channel organization is particularly useful for monitoring multiple control lines, implementing window comparators, or creating digital alarm logic. Open-collector outputs also suit systems that require a wired-AND bus or a pull-up voltage different from the comparator supply. When laying out a circuit, place the pull-up resistor and any input filtering components close to the relevant device pins, and route sensitive analog inputs away from switching nodes. Verify the common-mode range, differential input range, supply limits, and output pull-up voltage for the exact operating conditions. The 14-PDIP package is intended for through-hole assembly rather than compact surface-mount designs. This page combines the LM2901NG4 operating limits, interface characteristics, application guidance, package details, and validated drop-in alternatives with practical design notes for engineers comparing legacy quad comparators.

RFQ Contact
LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics
LM2901Q4T

LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2901Q4T is a four-channel low-power voltage comparator with a 2 V to 36 V single-supply range, support for ±1 V to ±18 V dual supplies, and a 16-QFN exposed-pad package measuring 3 mm by 3 mm. Each of its four channels compares an inverting input with a non-inverting input and supports open-collector output operation compatible with CMOS, DTL, TTL, MOS, and ECL logic families. A voltage comparator is an analog mixed-signal IC that evaluates two input voltages and changes its output when the difference crosses a defined threshold. The comparator category belongs to the broader interface IC and signal-conditioning hierarchy. Open-collector outputs permit several comparator outputs to share a wired bus when an external pull-up is present, making quad comparators useful for monitoring four independent signals in one compact device. The LM2901Q4T combines four independent comparison channels with very low supply current of 1.1 mA, input offset voltage of 1 mV, input bias current of 25 nA, and response times of 1.3 microseconds. Its rail-to-rail input capability lets each channel operate across the supply range. The operating-temperature range of -40°C to +125°C supports industrial and extended-temperature equipment, while the 3 mm by 3 mm QFN-16-EP package reduces board area compared with larger quad comparator packages. Each open-collector output can sink current while remaining in a high-impedance state when inactive. This architecture requires a pull-up resistor to establish a logic-high voltage. Because the output transistor can remain off, several channels may be connected to a common bus only when their wired-collector behavior and application logic are compatible. Input and output timing should be evaluated together when detecting slow crossings, short pulses, or noisy thresholds. Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, sensor threshold conditioning, window comparison, power-supply sequencing, and four-channel logic-level translation. The 2 V to 36 V supply range is particularly useful when the comparator must monitor signals above a conventional 5 V logic rail while operating from a higher system supply. For PCB design, place bypass capacitance close to the supply pins and route the exposed pad to a thermal copper area according to the manufacturer land pattern. Keep sensitive inverting and non-inverting traces short, avoid routing them beside high-current switching paths, and select the external output pull-up to establish the required logic-high level and sink-current margin. This product page combines exact electrical and package attributes, application-specific engineering guidance, threshold-level design notes, and a parameter comparison framework. It also distinguishes confirmed drop-in replacements from functionally similar devices whose channel count, package, or electrical behavior prevents direct PCB substitution.

RFQ Contact
LM2901VD - 36V Quad Differential Comparator | onsemi
LM2901VD

LM2901VD - 36V Quad Differential Comparator | onsemi

The onsemi LM2901VD is a four-channel differential comparator designed for level detection, low-level sensing, and memory applications, with a 3 V to 36 V operating range and a typical input bias current of 25 nA. The device is packaged in a 14-pin SOIC and provides open-collector outputs suitable for wired logic interfaces. Each of the four independent comparators compares its non-inverting and inverting inputs and produces a logic-level indication of their relative voltages. A differential comparator is an analog interface IC that converts the relationship between two input voltages into a digital output. In the broader semiconductor hierarchy, the LM2901VD belongs to the comparator family, which sits alongside amplifiers and other interface ICs. It is used where a system must establish whether a measured voltage is above or below a reference, such as in power-supply threshold detection, signal conditioning, and simple control systems. Key features include single-supply or split-supply operation, a typical input bias current of 25 nA, and a typical input offset current of ±5.0 nA. The low input bias current reduces loading on high-impedance source circuits, which is useful when the comparator monitors a sensor or resistor-divider output. The wide 3 V to 36 V supply range supports industrial control systems, automotive equipment, consumer products, and embedded memory interfaces. The open-collector output architecture requires an external pull-up resistor and permits the output to be pulled to a selected logic voltage. This feature enables connection to TTL-compatible systems and allows multiple comparator outputs to share a bus when suitable wired logic behavior is acceptable. The four independent channels can perform separate threshold, window, or sensing functions without sharing an internal signal path. Typical applications include overvoltage and undervoltage detection, battery monitoring, industrial sensor interfaces, memory address decoding, automotive logic systems, and general-purpose control equipment. Because the output is open collector, designers should account for pull-up resistor selection, output rise time, bus capacitance, and the voltage and current ratings of the pull-up network. The principal design consideration is common-mode and supply compatibility. Input and output conditions must remain within the limits stated in the manufacturer datasheet, and the external pull-up must not exceed the output transistor's voltage rating. The 14-pin SOIC footprint also requires adequate spacing between adjacent analog inputs to reduce noise coupling. This page combines the manufacturer function description, package information, electrical highlights, verified sourcing links, drop-in comparison options, and practical circuit-design guidance to support faster component evaluation and PCB planning.

RFQ Contact
LM2901VN - Quad 36V Comparator | onsemi | Through-Hole
LM2901VN

LM2901VN - Quad 36V Comparator | onsemi | Through-Hole

The onsemi LM2901VN is a quad differential voltage comparator with four independent channels, a 3 V to 36 V supply range, open-collector outputs, and a 14-pin PDIP package. The device is designed for general-purpose voltage comparison in industrial, automotive, power-control, and signal-conditioning systems, including applications where the input common-mode range extends to ground. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The comparator belongs to the broader signal-conditioning and interface hierarchy: voltage comparator, analog interface IC, semiconductor, and electronic component. Each LM2901VN channel provides inverting and non-inverting inputs, an output, and access to the ground reference. Its open-collector outputs allow wired-OR operation and require an external pull-up resistor when driving a logic input. Key features include four independent comparison channels in one package, operation from 3 V to 36 V, open-collector sinking capability, and a common-mode input voltage range that includes ground. The package is a 14-pin through-hole PDIP. Because the outputs are open collector, engineers can choose the pull-up voltage independently of the comparator supply when logic-interface requirements differ, while ensuring that the selected resistor and output transistor stay within their current limits. The LM2901VN provides the familiar LM2901 channel arrangement, with each comparator using separate input and output pins. Its monolithic construction places four independent channels on one substrate, reducing component count in designs that require multiple threshold, window, overvoltage, or undervoltage decisions. The wide operating supply range supports both low-voltage logic rails and higher-voltage industrial or automotive systems when the associated input and output ratings are respected. Typical uses include power-supply sequencing, battery monitoring, motor-control feedback, sensor threshold conditioning, industrial control logic, and automotive signal comparison. In a power-supply circuit, one channel can monitor a feedback-derived voltage against a reference while another channel supervises another rail. In a motor-control application, the comparator can evaluate a scaled current or position signal before driving a control transistor through an external interface stage. Designers should verify input and output voltage limits for the specific operating condition, account for the open-collector pull-up network, and ensure logic compatibility with the driven device. A pull-up resistor sets rise time and current, so it should be selected from the required sink-current and propagation-delay limits. Breadboard and prototype layouts should keep each comparator's input path short and away from noisy switching nodes to reduce false transitions. This product record combines the LM2901VN device identity, verified 3 V to 36 V and 14-pin PDIP characteristics, package-specific replacement guidance, comparison parameters, and practical circuit-design guidance. It is intended to support component selection, PCB-level replacement decisions, and application design without obscuring the differences between same-family and cross-manufacturer alternatives.

RFQ Contact
LM2902AMX - Quad 14-SOP Op Amp | onsemi | Signal Control
LM2902AMX

LM2902AMX - Quad 14-SOP Op Amp | onsemi | Signal Control

The onsemi LM2902AMX is a general-purpose quad operational amplifier in a 14-pin SOP package, providing four amplifier circuits with a 40 nA input bias current for industrial signal-conditioning, instrumentation, and low-voltage analog systems. The device is identified as a standard general-purpose amplifier with four circuits in a 14-SOP package, making it suitable for designs that need several amplifier channels while controlling component count and board area. An operational amplifier is an analog amplifier that uses very high open-loop gain and negative feedback to amplify small voltage differences. The quad LM2902AMX places four amplifiers in one package, each with its own two inputs and one output while sharing the supply pins. Within the product taxonomy, it is an operational amplifier within the broader amplifier IC and analog signal-processing categories. The LM2902AMX is specifically identified as a standard general-purpose amplifier, which makes it appropriate for buffering, current-to-voltage conversion, differential amplification, level shifting, and feedback-control circuits. Its 40 nA input bias current supports applications in which bias-related error must remain controlled around sensitive analog nodes. The 14-SOP package also provides a conventional surface-mount option for industrial, instrumentation, and embedded control equipment. Because four amplifier sections share one package, the device can reduce component count and simplify routing in multi-channel analog boards. Typical uses include amplifier banks in control panels, sensor conditioning channels, active filtering, and low-frequency analog signal processing. Designers should confirm input common-mode range, output swing, supply-voltage limits, offset voltage, input offset current, unity-gain bandwidth, slew rate, noise, and temperature limits against the manufacturer datasheet before finalizing a design. The principal design trade-off is that a general-purpose quad amplifier prioritizes flexibility and channel density rather than the very low offset, low noise, high bandwidth, or rail-to-rail performance available from specialized amplifier families. Applications operating from a single supply, near the positive rail, or with very small sensor signals may require additional output biasing or a different amplifier architecture. Decoupling capacitors, input protection, output loading, and stability with capacitive loads must also be evaluated per circuit. This page combines package and catalog information with application guidance, drop-in replacement comparisons, and practical design notes. It is intended to help engineers qualify the LM2902AMX for industrial analog boards faster than by reading the datasheet and distributor listings separately.

RFQ Contact
LM2902AQS14-13 - Quad 36V Automotive Op Amp | Diodes
LM2902AQS14-13

LM2902AQS14-13 - Quad 36V Automotive Op Amp | Diodes

Diodes Incorporated LM2902AQS14-13 is a four-circuit general-purpose operational amplifier designed for automotive-compliant applications, with a 3V to 36V single-supply range, a 20 nA input bias current, and a 14-pin SOIC package. The amplifier combines approximately 1 mV typical input offset voltage, 100 dB DC voltage gain, and 700 kHz unity-gain bandwidth in one package. An operational amplifier is a voltage-gain circuit that compares an inverting input with a non-inverting input and drives its output toward the difference between them. Operational amplifiers belong to the broader analog IC and signal-conditioning hierarchy. They are commonly used for sensor amplification, error amplification, voltage buffering, filtering, and analog-to-digital converter input conditioning. The LM2902 family is intended for general-purpose designs where four amplifiers and relatively wide supply-voltage tolerance provide more utility than a single precision amplifier. The principal electrical features include a 3V to 36V single-supply operating range, operation from ±1.5V to ±18V on dual supplies, and supply-current drain that is largely independent of supply voltage. Each amplifier supports rail-to-rail input operation, has a typical input bias current of 20 nA, and offers a typical open-loop DC gain of 100 dB. The temperature-compensated unity-gain bandwidth is 700 kHz, while the listed slew rate is 0.3 V/µs. The A-grade offset specification is 1 mV typical, making the device suitable for general signal-conditioning applications that do not require the tighter matching of a precision instrumentation amplifier. Internally compensated amplifiers simplify closed-loop gain selection, and the four independent channels can implement separate gain, filtering, comparison, buffering, or feedback functions. Their broad supply range also permits operation from industrial 24V supplies when designers observe the absolute maximum and common-mode limits. Typical uses include automotive sensor interfaces, industrial control loops, battery-powered instrumentation, transducer signal conditioning, low-current motor control, analog monitoring, and multichannel test equipment. The 14-pin SOIC footprint supports conventional surface-mount assembly and is useful when four channels must fit into one package. Common-mode and output-swing headroom should be checked against the actual signal and load because a wide supply rating does not mean the inputs and outputs can reach every supply rail under all conditions. A practical design starts by confirming the automotive-compliant variant requirement, power-supply range, input common-mode range, output swing, load capability, and noise-sensitive signal path. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they remain in a defined state. The SOIC package should be inspected for assembly-layout requirements and the complete operating limits in the manufacturer datasheet. This product overview combines the LM2902AQS14-13 electrical characteristics with package guidance, design considerations, and verified drop-in comparison options. It is intended to help engineers evaluate channel count, supply tolerance, offset performance, bandwidth, and automotive suitability before committing to a PCB design.

RFQ Contact
LM2902AQT14-13 - 36V Quad Op Amp | Diodes Incorporated
LM2902AQT14-13

LM2902AQT14-13 - 36V Quad Op Amp | Diodes Incorporated

The Diodes Incorporated LM2902AQT14-13 is a four-channel general-purpose operational amplifier designed for automotive and industrial systems operating from a single 3 V to 36 V supply or from dual supplies of ±1.5 V to ±18 V. Each amplifier provides 700 kHz unity-gain bandwidth, 0.3 V/us slew rate, 100 dB large-signal voltage gain, 700 uA typical supply current, and 20 nA typical input bias current. The device is packaged in a 14-pin TSSOP. An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set its gain. A quad op amp combines four amplifiers in one package, allowing designers to implement four independent analog signal-conditioning channels while reducing board area. Within the broader semiconductor hierarchy, the LM2902AQT14-13 belongs to the linear amplifier and analog signal-conditioning IC category. The automotive-qualified LM2902A variant provides a typical input offset voltage of 1 mV, compared with 2 mV for the non-A LM2902 version. Its wide supply range covers 12 V and 24 V automotive rails, while its common-mode input and output capabilities suit sensor buffering, actuator interfaces, and low-frequency control loops. Low input bias current of 20 nA helps preserve accuracy when driving high-impedance sensors. The internal architecture is internally compensated for stable unity-gain operation, allowing each channel to operate as a voltage follower, inverting amplifier, non-inverting amplifier, comparator, or differential input stage. With 700 kHz bandwidth and 0.3 V/us slew rate, the device handles general-purpose analog signals rather than demanding high-speed precision applications. Typical uses include battery-management-system sensor interfaces, automotive body and chassis control, industrial transducers, instrumentation amplifiers, active filters, and 4-to-20 mA current-loop receivers. The 14-TSSOP package also makes the quad amplifier practical for compact control boards where every square millimeter matters. When laying out the PCB, keep input and feedback traces short, place input-biasing resistors close to the non-inverting inputs, and provide stable bypass capacitance at the supply pins. Verify common-mode headroom at the selected output level and confirm the operating temperature rating against the vehicle or industrial environment before release. This page consolidates supply-range, bandwidth, offset, automotive-qualification, pinout, and drop-in replacement information, and adds application-specific design guidance that helps shorten component selection and board-layout decisions.

RFQ Contact
LM2902AS14-13 - Quad 36V Op Amp | Diodes Incorporated
LM2902AS14-13

LM2902AS14-13 - Quad 36V Op Amp | Diodes Incorporated

Diodes Incorporated LM2902AS14-13 is a standard general-purpose quad operational amplifier with four amplifier circuits, a 3 V to 36 V supply range, 1.3 MHz gain-bandwidth product, 100 dB open-loop gain, and 375 uA typical quiescent current. The device is supplied in a 14-pin surface-mount SO package. An operational amplifier, or op amp, is a high-gain analog signal-conditioning component used to amplify voltage differences, buffer sensors, and drive external circuits. The LM2902 belongs to the quad operational amplifier hierarchy, combining four amplifiers in one package. It is intended for general-purpose industrial and instrumentation applications operating from single or dual supplies. The principal features of the LM2902AS14-13 include a wide 3 V minimum supply, 36 V maximum supply, 1 mV maximum input offset voltage, 1.3 MHz gain-bandwidth product, and 100 dB open-loop gain. Its 375 uA typical quiescent current supports low-power signal processing, while the 14-SO package simplifies assembly on conventional surface-mount PCB layouts. The four amplifier sections provide common functions such as non-inverting and inverting gain, voltage followers, comparators, transducers, and instrumentation interfaces. Because all four sections are integrated in one package, a complete analog signal-conditioning channel can be implemented without using four separate single amplifiers. PCB designers should preserve input/output symmetry and route high-impedance input signals away from switching nodes and supply-current paths. Typical applications include industrial sensor conditioning, transducer amplification, current-loop interfacing, audio preamplification, instrumentation amplifiers, active filters, and general low-frequency signal processing. The 3 V to 36 V operating range permits operation from conventional 5 V, 12 V, and 24 V supply systems, subject to the maximum total supply and input common-mode constraints. When designing a new circuit, check the input common-mode range, output swing, slew rate, and stability requirements at the intended operating frequency. Add supply-bypass capacitors close to the device and avoid placing sensitive input traces beside digital switching paths. The SO-14 footprint requires confirmation against the current PCB footprint before substitution. This product page combines operating limits, application guidance, package information, drop-in comparison options, and practical PCB considerations. It is intended to help engineers evaluate the LM2902AS14-13 for new designs and legacy repairs without treating every similarly rated amplifier as a functional substitute.

RFQ Contact
LM2902AT14-13 - Quad 1.3MHz Op Amp | Diodes Incorporated
LM2902AT14-13

LM2902AT14-13 - Quad 1.3MHz Op Amp | Diodes Incorporated

Diodes Incorporated LM2902AT14-13 is a general-purpose quad operational amplifier containing four amplifier channels in a 14-pin TSSOP package. The device operates with a 1.3 MHz gain-bandwidth product, offers 100 dB open-loop gain, and draws 375 uA supply current per amplifier. Its four-channel integration makes it suitable for compact analog signal-conditioning boards requiring multiple independently configured amplifier stages. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier used to amplify, filter, buffer, compare, or control analog signals. The LM2902 family belongs to the broader voltage-amplifier and analog-signal-processing hierarchy. It is intended for general-purpose designs rather than precision or high-speed signal chains, making it useful for transducers, sensor interfaces, audio paths, and control systems where economy, low power, and functional integration are priorities. The quad configuration provides four amplifiers in one package, reducing board area compared with four separate single or dual amplifier packages. The 1.3 MHz gain-bandwidth product supports applications requiring moderate rather than very high closed-loop bandwidth. Its 100 dB open-loop gain provides substantial correction capability, while the 375 uA operating current per channel supports low-power analog systems. Operating from a single supply is useful when negative supply rails are unavailable or undesirable. The LM2902 uses a conventional general-purpose amplifier architecture intended for moderate accuracy and broad operating conditions. Because the four channels share one package, their supply, ground, and thermal environments are closely related. Designers should preserve adequate stability around each amplifier, account for input common-mode range and output swing, and avoid relying on rail-to-rail input or output operation. The 1.3 MHz bandwidth also makes stability and noise considerations more important than in precision, low-offset alternatives. Typical uses include four-channel sensor conditioning, low-frequency active filtering, audio preamplification, comparator-style threshold circuits, current-to-voltage conversion, and general industrial control. The package is particularly useful when several low-frequency analog channels must be consolidated on a compact board. Its automotive temperature grade makes it relevant to vehicle electronics, provided each electrical limit is evaluated against the complete operating environment. A primary design consideration is the voltage-loss margin required by a non-rail-to-rail amplifier. Input and output voltage ranges must be checked against the actual supply voltage and signal amplitude. Decoupling should be placed close to the supply pins, the unused amplifier channel should be configured according to the manufacturer's recommendations, and PCB grounding should minimize voltage-drop and feedback coupling between sensitive channels. This product record combines the LM2902AT14-13 specifications with package guidance, application-oriented design notes, and a strict compatibility review. It helps engineers determine whether the quad TSSOP implementation fits a power-conscious analog design before committing to a board layout or production release.

RFQ Contact
LM2902AWYDT - Quad 1.3MHz Op Amp, 14-SO | STMicroelectronics
LM2902AWYDT

LM2902AWYDT - Quad 1.3MHz Op Amp, 14-SO | STMicroelectronics

The STMicroelectronics LM2902AWYDT is a low-power quad operational amplifier with four internally compensated amplifiers, 1.3 MHz gain-bandwidth performance, and 100 dB typical open-loop gain. It is packaged in a 14-pin small-outline package identified as 14-SO and is intended for general-purpose signal conditioning across automotive and industrial control systems. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The quad configuration integrates four independent amplifiers into one 14-SO package. Internal frequency compensation simplifies closed-loop design, while a common power architecture allows the four amplifiers to operate from a single supply over a wide voltage range. The LM2902 family therefore provides more functional density than discrete single amplifiers and reduces the number of components needed for multi-channel analog circuits. Key electrical characteristics include a 1.3 MHz gain-bandwidth product, 100 dB typical gain, approximately 375 uA supply current per amplifier, 20 nA input bias current, 2 nA input offset current, and 800 V input differential voltage capability. These characteristics support general-purpose applications where low power, usable bandwidth, and moderate input precision are more important than high-speed or precision amplifier performance. The device uses four independent operational amplifiers with internally implemented frequency compensation. Its push-pull output stage supports output-current demands commonly encountered in buffer, comparator-style, and analog-control circuits. The operating approach is suited to single-supply systems, where an amplifier may operate from an input and output signal referenced to the same supply rail rather than requiring a symmetrical positive and negative supply. Typical uses include industrial process-control loops, automotive interface circuits, sensor conditioning, current-to-voltage conversion, low-frequency active filters, and general signal amplification. The four amplifiers can process related channels or provide separate functions such as amplification, filtering, thresholding, and buffering on one PCB. For designs requiring more precision or bandwidth, the device should be compared against the corresponding performance limits before compensation, noise, or offset requirements are finalized. Layout should preserve short feedback paths, maintain suitable grounding, and place input and output decoupling close to the device. Because this is a general-purpose quad amplifier, stability is commonly established with the manufacturer's recommended compensation approach and output isolation resistors where capacitive loading requires them. Verify input and output common-mode limits, supply voltage, load current, and thermal conditions against the manufacturer datasheet before releasing the circuit. This product record combines the LM2902AWYDT device identity, package information, principal electrical characteristics, sourcing context, and verified drop-in alternatives. It also adds practical guidance for comparing the STMicroelectronics LM2902 family with pin-compatible single-supply quad amplifiers from Texas Instruments and NXP Semiconductors.

RFQ Contact