Products (44,000+)

LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics
LM2902AWYPT

LM2902AWYPT - 1.3MHz Quad Op Amp, 14-TSSOP | STMicroelectronics

STMicroelectronics LM2902AWYPT is a low-power, general-purpose quad operational amplifier with four push-pull amplifier channels, a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and a 14-TSSOP package. It is designed for compact analog signal-conditioning systems that require four amplifiers in one package. The manufacturer identifies the device as a low-power quad operational amplifier for instrumentation and general-purpose amplifier applications. An operational amplifier is a high-gain, high-impedance differential amplifier whose closed-loop behavior is determined mainly by external feedback components. The quad LM2902A configuration places four independent amplifiers in one package, reducing component count and board area compared with four separate single or dual amplifier packages. In the broader semiconductor hierarchy, an operational amplifier is an analog IC, a signal-conditioning IC, and part of the wider linear and mixed-signal semiconductor family. Key electrical attributes include a 1.3 MHz gain-bandwidth product, 100 dB common-mode rejection, and 375 µA typical quiescent current. The input bias-current figures listed for this device are 20 nA and 2 nA for different operating conditions, while its stated withstand voltage is 800 V. These characteristics make the LM2902AWYPT suitable for low-frequency instrumentation, sensor interfaces, transducers, and general feedback-control circuits where four amplifier channels can share a common supply architecture. The push-pull output stage supports bidirectional output current without the crossover distortion commonly associated with older single-ended output designs. Each amplifier can implement non-inverting, inverting, summing, difference, comparator-style, or active-filter configurations when operated within its electrical limits. Independent channels allow one package to serve several signal paths, although each channel requires correct feedback and decoupling arrangements to prevent unintended oscillation or channel interaction. Typical uses include low-frequency sensor conditioning, process-control instrumentation, current-voltage conversion, sample-and-hold circuitry, audio preamplification, active filtering, and general-purpose differential amplification. Four channels in one 14-TSSOP package can be especially useful in sensor nodes where several measurements must be conditioned before conversion or control. The package also supports compact mixed-signal boards where conserving board area is more important than very high slew rate or rail-to-rail input and output operation. Designers should begin with the pin-description table and typical application circuits in the STMicroelectronics datasheet. Place the supply bypass capacitor close to the device, keep feedback-loop routing compact, and route each output only to its assigned load. Confirm that input and output common-mode voltages remain within the amplifier's permitted operating range and that source and load impedances preserve stability with the selected feedback network. This product page consolidates the exact manufacturer-listing attributes, package information, commercially available replacement data, and application guidance for LM2902AWYPT. It also distinguishes verified electrical characteristics from parameters that require confirmation in the full manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer documentation conflicts.

RFQ Contact
LM2902D - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902D

LM2902D - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902D is a general-purpose quad operational amplifier built with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz typical gain-bandwidth product, and 2 mV typical input offset voltage in a 14-pin SOIC package. It supports single-supply or split-supply operation and is designed for instrumentation, buffering, amplification, and general analog signal-chain applications. An operational amplifier is a voltage-gain amplifier that uses negative feedback to control gain, bandwidth, input impedance, and output behavior. The quad LM2902 combines four amplifiers in one integrated circuit, reducing board area compared with four separate single or dual amplifier packages. Its general-purpose architecture belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy and is widely used where inexpensive, robust signal conditioning is more important than precision or high speed. Key characteristics include four independent amplifier channels, push-pull output capability, a 1.2 MHz typical gain-bandwidth product, and 2 mV typical offset voltage. The 26 V maximum supply rating provides compatibility with common industrial voltage ranges. According to the Texas Instruments LM2902 product page, the device is a quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifier. The distributor listing identifies the LM2902D orderable package as 14-SOIC. The internal architecture is frequency compensated and intended to operate from a single supply or split supply over a wide voltage range. Each amplifier can be used independently, while the common package provides four channels for instrumentation, sensor interfaces, active filters, voltage followers, and signal-conditioning blocks. The device should be selected against the complete input/output voltage, common-mode range, output-current, noise, and thermal requirements of the target circuit. Typical applications include industrial measurement, transducer interfaces, audio and control circuits, low-frequency active filters, sensor amplifiers, and general-purpose analog signal conditioning. Because it is a general-purpose amplifier, the LM2902D is most appropriate when system cost, supply tolerance, and availability matter more than very low offset, rail-to-rail operation, or high-frequency precision. The primary design consideration is supply and signal-range verification. Confirm that every input and output remains within the device's specified operating limits under load, temperature, and supply variation. Decoupling capacitors should be placed close to the supply pins, and each amplifier channel requires appropriate feedback and biasing. PCB creepage, grounding, output loading, and decoupling should be checked during layout. This page combines verified manufacturer and distributor information, drop-in replacement guidance, package comparison data, and practical design notes to help engineers evaluate the LM2902D for new designs and service replacements.

RFQ Contact
LM2902DG - 4-Channel 1 MHz Op Amp | onsemi | SOIC-14
LM2902DG

LM2902DG - 4-Channel 1 MHz Op Amp | onsemi | SOIC-14

onsemi LM2902DG is a single-supply, quad operational amplifier with four amplifiers, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a 3 V to 32 V supply-voltage range in a 14-pin SOIC package. The device uses true differential inputs and provides four independent general-purpose amplifier channels in one compact circuit. An operational amplifier, commonly shortened to op amp, is an analog integrated circuit that amplifies the difference between two input voltages. A quad operational amplifier integrates four amplifiers into one package. Within the device hierarchy, LM2902DG belongs to the operational-amplifier, analog-amplifier, and integrated-circuit categories. Its differential input structure makes it useful for amplifying sensor signals, buffering analog voltages, and implementing general-purpose analog signal-conditioning circuits. Key operating characteristics include a 1 MHz gain-bandwidth product and 0.6 V/µs slew rate. The 3 V minimum supply voltage supports low-voltage analog systems, while operation up to 32 V covers higher-voltage industrial signal chains. Four independent channels reduce package count and simplify board design when multiple analog signals must be amplified, buffered, or filtered. The LM2902 family uses the LM324-series architecture optimized for single-supply operation. True differential inputs allow each amplifier to respond to the voltage difference between its inverting and non-inverting terminals. Because the four channels share one package, designers must consider common supply and ground connections, output-current behavior, stability with capacitive loads, and power dissipation when all channels operate simultaneously. Typical uses include industrial sensor interfaces, low-side current measurement, analog signal conditioning, transducer amplification, general-purpose buffer stages, and four-channel control systems. A single package can implement four similar signal paths, provided each channel remains within its input-voltage, output-swing, current, and stability limits. A key design consideration is the relationship between supply voltage, output swing, and input common-mode range. Confirm that incoming sensor signals remain within the amplifier's permitted input range and that the required output voltage can be reached with the selected load. Place bypass capacitors close to the supply pins and route the common ground connection carefully to minimize offset and noise coupling. This product page combines the exact LM2902DG electrical and package identifiers with engineering-focused selection guidance, drop-in cross-reference information, comparison parameters, and practical PCB design notes. It is intended to help engineers determine package compatibility, verify key operating limits, and select a replacement without overlooking changes in amplifier performance or environmental requirements.

RFQ Contact
LM2902DG4 - Quad 1.2MHz Op Amp, 26V | Texas Instruments
LM2902DG4

LM2902DG4 - Quad 1.2MHz Op Amp, 26V | Texas Instruments

Texas Instruments LM2902DG4 is a general-purpose quadruple operational amplifier packaged in a 14-pin SOIC tube. Each of its four independent amplifier sections has a gain-bandwidth product of 1.2 MHz and a slew rate of 0.5 V/µs. The device supports single-supply operation up to 26 V and split-supply operation up to ±13 V, with an input offset voltage of 2 mV. Its four-amplifier configuration consolidates multiple analog signal-conditioning channels into one package. A general-purpose operational amplifier is an analog IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902 belongs to the operational-amplifier hierarchy, which includes instrumentation, comparator, voltage-feedback, and current-feedback devices. Four independent sections allow a single LM2902DG4 to implement functions such as sensing, buffering, error amplification, active filtering, and output-current buffering when their common-mode, voltage, and timing requirements overlap. The LM2902's principal characteristics include four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 0.5 V/µs slew rate, and a typical supply-current drain of 0.8 mA. Its input offset voltage is specified as 2 mV, while the operating supply range extends to 26 V on a single supply or ±13 V from a split supply. These characteristics make the device appropriate for general-purpose industrial control, analog signal conditioning, and low-to-moderate-frequency closed-loop applications. The LM2902 is designed around four internally compensated, high-gain operational-amplifier sections. Its 1.2 MHz gain-bandwidth product limits the closed-loop bandwidth achievable at a given noise gain, while the 0.5 V/µs slew rate governs large-signal response. Because all four sections share the same package and supply pins, layout should preserve short feedback paths and provide suitable supply bypassing close to the device. Typical uses include transducer-signal conditioning, low-frequency active filters, industrial sensor interfaces, control-loop error amplifiers, and analog signal buffers. A single package is particularly useful when a board needs several similar amplifier channels and designers want to reduce component count. For applications requiring precision offsets, wider bandwidth, lower noise, rail-to-rail inputs or outputs, or automotive qualification, the design should use a more specialized amplifier rather than assume the LM2902 provides those capabilities. When laying out a board, place the bypass capacitor at the supply pins and route feedback components close to the relevant amplifier section. Check input and output swing against the actual load because the usable signal range depends on the supply voltage and output-load conditions. For stable operation, confirm that the intended noise gain and closed-loop gain are compatible with the 1.2 MHz gain-bandwidth product and that the resulting output slew requirement remains below 0.5 V/µs. This page organizes the LM2902DG4 specifications, pinout, practical design guidance, application examples, and verified drop-in alternatives into one engineering reference. It also separates core device characteristics from procurement details so designers can evaluate the amplifier's package, supply range, bandwidth, and replacement options before committing it to a PCB design.

RFQ Contact
LM2902DR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM2902DR

LM2902DR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM2902DR is a general-purpose quad operational amplifier built with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz typical gain-bandwidth product, and 2 mV typical input offset voltage in a 14-pin SOIC package. It supports single-supply or split-supply operation and is designed for instrumentation, buffering, amplification, and general analog signal-chain applications. An operational amplifier is a voltage-gain amplifier that uses negative feedback to control gain, bandwidth, input impedance, and output behavior. The quad LM2902 combines four amplifiers in one integrated circuit, reducing board area compared with four separate single or dual amplifier packages. Its general-purpose architecture belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy and is widely used where inexpensive, robust signal conditioning is more important than precision or high speed. Key characteristics include four independent amplifier channels, push-pull output capability, a 1.2 MHz typical gain-bandwidth product, and 2 mV typical offset voltage. The 26 V maximum supply rating provides compatibility with common industrial voltage ranges. According to the Texas Instruments LM2902 product page, the device is a quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifier. The distributor listing identifies the LM2902DR orderable package as 14-SOIC. The internal architecture is frequency compensated and intended to operate from a single supply or split supply over a wide voltage range. Each amplifier can be used independently, while the common package provides four channels for instrumentation, sensor interfaces, active filters, voltage followers, and signal-conditioning blocks. The device should be selected against the complete input/output voltage, common-mode range, output-current, noise, and thermal requirements of the target circuit. Typical applications include industrial measurement, transducer interfaces, audio and control circuits, low-frequency active filters, sensor amplifiers, and general-purpose analog signal conditioning. Because it is a general-purpose amplifier, the LM2902DR is most appropriate when system cost, supply tolerance, and availability matter more than very low offset, rail-to-rail operation, or high-frequency precision. The primary design consideration is supply and signal-range verification. Confirm that every input and output remains within the device's specified operating limits under load, temperature, and supply variation. Decoupling capacitors should be placed close to the supply pins, and each amplifier channel requires appropriate feedback and biasing. PCB creepage, grounding, output loading, and decoupling should be checked during layout. This page combines verified manufacturer and distributor information, drop-in replacement guidance, package comparison data, and practical design notes to help engineers evaluate the LM2902DR for new designs and service replacements.

RFQ Contact
LM2902DR2 - Quad Single-Supply Op Amp | onsemi | SOIC-14
LM2902DR2

LM2902DR2 - Quad Single-Supply Op Amp | onsemi | SOIC-14

The onsemi LM2902DR2 is a single-supply, quad operational amplifier packaged in a 14-pin SOIC. It integrates four independent amplifiers in the LM2902 family, combining differential inputs, low input offset voltage, and a high gain-bandwidth product for general-purpose analog signal conditioning. The LM2902 family supports supply voltages up to 36 V and can also operate from split supplies when supported by the device operating conditions. Its four-amplifier arrangement reduces package count and simplifies board layout where multiple analog channels are required. An operational amplifier is a high-gain, frequency-compensated analog building block used to amplify differential signals, buffer inputs, compare voltages, and drive feedback-control networks. The LM2902 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, signal-conditioning IC, and power-management semiconductor. Its differential-input architecture requires the two input voltages to be considered together, while its common-mode input range can extend to ground for many single-supply applications. The principal benefits of the LM2902DR2 are its four integrated channels, 36 V supply capability, low input offset voltage, and high gain-bandwidth product. Four independent amplifiers in one 14-pin package simplify designs that require several matched circuit functions, such as sensor conditioning, active filtering, or control-loop sections. The low offset voltage helps reduce output error when the amplifier is used with negative feedback, although the actual error also depends on input bias current, resistor matching, temperature, and common-mode operating conditions. The LM2902DR2 is part of the established LM324-family class of low-cost, single-supply quad operational amplifiers with true differential inputs. Because the device is frequency compensated, designers can create stable closed-loop gain stages without adding external compensation capacitors in typical applications. Its 14-pin SOIC footprint supports conventional surface-mount assembly and is also convenient for prototypes, hobbyist boards, education kits, and repair platforms that use the standard quad-op-amp outline. Typical uses include industrial sensor interfaces, low-frequency audio amplification, active filters, comparator-style signal conditioning, and general instrumentation. The quad organization is particularly useful when a circuit needs two or more gain stages, an amplifier-based filter, or multiple independent analog channels. For power-sensitive systems, the 36 V operating class also allows the device to sit behind higher-voltage supplies when the application and protection requirements permit it. When designing a board around the LM2902DR2, check supply voltage, common-mode range, output swing, input bias current, and the required closed-loop gain at the operating frequency. Place input and feedback components close to the relevant amplifier pins, and keep sensitive input nodes away from switching-current paths. Decouple each supply rail near the device, and confirm that every connected output remains within its valid output-voltage range under worst-case load and temperature conditions. This product page combines the LM2902DR2 technical description, package details, sourcing workflow, application guidance, and verified drop-in alternatives. It also organizes parameter comparisons and practical PCB considerations so engineers can evaluate the device, its replacements, and its role in a complete analog signal chain before releasing a design.

RFQ Contact
LM2902DR2G - Quad 3-26V Operational Amplifier | onsemi
LM2902DR2G

LM2902DR2G - Quad 3-26V Operational Amplifier | onsemi

The onsemi LM2902DR2G is a quad general-purpose operational amplifier designed for single-supply operation from 3 V to 26 V. The device contains four amplifiers in a 14-pin SOIC package, making it suitable for instrumentation, buffering, signal conditioning, and general analog signal-processing circuits. Its integrated design allows four amplifier channels to be placed in one compact package while supporting common single-supply architectures. A general-purpose operational amplifier is a voltage-amplifying active device that uses differential inputs and feedback to control gain, filtering, buffering, and signal conditioning. The quad LM2902 family combines four amplifiers within one semiconductor package, reducing board area and simplifying designs that require multiple independent analog channels. The LM2902DR2G is associated with the onsemi LM2902 family and is identified by distributor listings as a single-supply quad operational amplifier in a 14-SOIC package. The key device characteristics are the four-amplifier configuration, 3 V to 26 V supply range, 14-SOIC package, and general-purpose single-supply operation. These specifications make the device suitable for industrial control systems, sensor interfaces, low-frequency signal conditioning, audio and communications support circuits, and general instrumentation. Because the LM2902 is a general-purpose amplifier rather than a precision or high-speed part, designers should verify input bias current, output swing, noise, slew rate, and stability requirements against the manufacturer datasheet for the actual operating conditions. In a typical single-supply design, the LM2902 is powered from a positive supply while the signal source and reference point are biased near ground. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased so that they remain in a defined operating state. Feedback-network values determine gain and bandwidth, so resistor and capacitor tolerances directly influence signal accuracy. The device should also be evaluated for output-current capability and thermal rise when driving capacitive loads or operating at elevated temperatures. Common uses include sensor signal conditioning, low-level instrumentation, control-loop input stages, active filtering, waveform conditioning, and general-purpose buffering. The 14-SOIC package provides a familiar footprint for designs using standard through-hole assembly, although the exposed thermal behavior and electrical limits remain important at higher ambient temperatures. The LM2902DR2G is therefore best suited to cost-sensitive, low-to-moderate-frequency analog systems where four channels and single-supply convenience matter more than precision or high bandwidth. This page summarizes the device identity, package, operating range, sourcing information, drop-in alternatives, application guidance, and engineering considerations for engineers evaluating LM2902DR2G. The manufacturer datasheet should be consulted for the complete electrical characteristics, recommended operating conditions, pinout, and application details before final circuit release.

RFQ Contact
LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRE4

LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRE4 is a quad general-purpose operational amplifier with a 26 V maximum supply, 1.2 MHz gain-bandwidth product, and 2 mV typical input offset voltage, housed in a 14-pin SOIC package. The device contains four independent operational amplifiers designed for a broad range of low-frequency signal-conditioning applications. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier with high input impedance and low output impedance. Its feedback network can configure the device as a voltage amplifier, comparator, buffer, summing amplifier, or active filter. The LM2902 belongs to the operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor hierarchies, making it suitable for common industrial, instrumentation, audio, control, and interface circuits. The LM2902DRE4 provides four amplifier channels in one package, reducing board area and simplifying multi-channel designs. Key characteristics include a typical gain-bandwidth product of 1.2 MHz, 0.5 V/µs slew rate, 0.8 mA typical supply-current drain, and low 2 mV input offset voltage. Its wide operating supply range supports single-supply operation up to 26 V and dual-supply operation up to ±13 V. The architecture supports a broad input common-mode range while maintaining low supply-current consumption independent of supply voltage. These characteristics make the amplifier suitable for battery-powered instrumentation, process-control signals, sensor interfaces, audio preamplification, active filtering, and general-purpose analog systems. Because all four amplifiers operate from common supply pins, board designers can simplify rail distribution and decoupling. Typical applications include four-channel sensor conditioning, low-frequency active filters, audio mixer stages, comparator circuits, industrial control interfaces, and instrumentation amplifiers built from discrete op-amp stages. The 14-pin SOIC package is also practical for through-hole prototype assembly and conventional surface-mount production, while the −40 °C to +125 °C temperature range supports industrial environments. Design carefully around input and output voltage limits, common-mode range, output-current capability, and the load presented by the feedback network. Place supply-bypass capacitors close to the positive and negative supply pins, keep feedback traces short, and verify stability with the actual source and load impedances. The manufacturer datasheet and pin-description table should control PCB and schematic assignments. This page combines the LM2902DRE4 electrical characteristics, package details, drop-in alternatives, comparison parameters, and practical application guidance to support faster component selection and board-level implementation.

RFQ Contact
LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG3

LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRG3 is a general-purpose quadruple operational amplifier with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage in a 14-pin SOIC package. The LM2902DRG3 suffix denotes a tape-and-reel shipping configuration. An operational amplifier, or op amp, is a high-gain analog signal-processing component used to amplify voltage differences, buffer sensors, drive analog inputs, and implement feedback-control circuits. The LM2902 belongs to the quad operational-amplifier family within the broader voltage-amplifier and analog-signal-processing semiconductor hierarchy. Its four amplifiers share power-supply pins but have independent input and output connections, allowing one package to implement four related analog functions. The LM2902 operates from single or split supplies over a wide voltage range, making it useful in industrial-control, instrumentation, and audio circuits. Key characteristics include a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and approximately 0.8 mA typical supply-current drain. Four frequency-compensated amplifiers support common closed-loop configurations including noninverting and inverting gain, voltage followers, comparators, summing amplifiers, and difference stages. Its 14-pin SOIC package provides a familiar industrial footprint and thermal performance suitable for conventional through-hole assembly workflows. Because each channel is independent, the IC can implement sensor conditioning, signal amplification, active filtering, and control-loop functions on one board. Single-supply operation simplifies designs where the signal remains above ground, while split-supply operation supports bipolar signals centered around zero volts. Typical applications include industrial sensor interfaces, transducers, audio preamplifiers, analog-to-digital converter input conditioning, motor-control support circuits, and general-purpose instrumentation. The wide supply range and low supply-current drain make the device practical in equipment powered from industrial rails or split supplies, provided the absolute maximum operating limits remain respected. Designers should verify input and output common-mode limits for each supply configuration, account for the offset voltage when precision is important, and use stable feedback networks for unity-gain or noise-sensitive applications. PCB placement should keep sensitive input nodes compact, provide an appropriate ground-return path, and avoid placing high-current switching paths close to amplifier inputs. This product page combines the LM2902 family specifications, package information, sourcing guidance, verified drop-in candidates, application examples, and practical design considerations. The comparisons also distinguish package-compatible alternatives from choices that require different qualification, temperature-range, or performance checks before substitution.

RFQ Contact
LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG4

LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902DRG4 is a four-channel operational amplifier with a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input-offset specification in a 14-pin SOIC package. Designed for general-purpose signal conditioning, each amplifier can operate from single or dual supplies, supporting a broad range of industrial, instrumentation, control, and analog-interface applications. An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The LM2902 belongs to the operational-amplifier hierarchy, where it combines transistor-level input and output stages with internal compensation. Each of its four channels can perform amplification, buffering, comparison, summation, differential sensing, or active-filter functions without requiring a separate amplifier for every signal path. The device provides a 1.2 MHz gain-bandwidth product and a 2 mV input-offset specification, making it suitable for moderate-bandwidth precision applications. The 26 V supply capability also supports higher-voltage industrial interfaces than low-voltage rail-to-rail amplifiers. Texas Instruments specifies an operating temperature range from -40°C to 125°C, allowing operation across demanding commercial and industrial environments. The four amplifiers share one package while retaining independent input and output pins, allowing one IC to implement several analog functions. Their typical design role is to operate with feedback networks that establish closed-loop gain and filtering. Because the device is not rail-to-rail by specification, input and output common-mode limits must be checked against the selected supply voltage and signal range before layout release. Typical uses include transducer signal conditioning, low-frequency active filters, sensor amplifiers, industrial control loops, comparator-style threshold circuits, and audio or communications interface stages. The SOIC package also simplifies inspection and rework on through-hole industrial boards while providing a familiar 14-pin land pattern. For a new design, verify the input and output common-mode range, output-current capability, load impedance, and supply operating limits at the intended signal amplitude. Stable feedback and proper decoupling remain important even when the application is a unity-gain buffer, so use the manufacturer pin-description table when assigning PCB tracks. This page organizes the LM2902DRG4 specifications, verified manufacturer references, same-package alternatives, application guidance, and comparison points. It also highlights the practical checks needed to determine whether a candidate replacement is truly pin-compatible rather than merely functionally similar.

RFQ Contact
LM2902DT - Quad Op-Amp, 3-30V, SOIC-14 | STMicroelectronics
LM2902DT

LM2902DT - Quad Op-Amp, 3-30V, SOIC-14 | STMicroelectronics

The STMicroelectronics LM2902DT is a low-power quad operational amplifier with four independent, high-gain, internally frequency-compensated amplifier stages, a 1.3 MHz gain-bandwidth, 0.4 V/us slew rate, and a wide 3 V to 30 V single-supply operating range, housed in a 14-pin SOIC package. An operational amplifier (op-amp) is an analog building block within the broader amplifier IC and linear IC families that amplifies the voltage difference between its two inputs. Quad op-amps integrate four of these stages in one package, letting a single IC handle multi-channel signal conditioning - sensor buffers, comparators-with-hysteresis, active filters, and summing stages - while sharing one supply rail and saving board area versus four single amplifiers. Key features of the LM2902DT include single-supply operation from 3 V to 30 V (or dual supplies from +/-1.5 V to +/-15 V), an input common-mode range that extends to the negative rail, a 2 mV maximum input offset voltage, and approximately 20 nA input bias current - tighter than the classic LM324 (7 mV offset, 45 nA bias) - which improves accuracy in high-impedance sensor circuits. The bipolar process keeps quiescent current low, and output stages are push-pull with a classic footprint-compatible pinout shared industry-wide. Per STMicroelectronics, the LM2902 family was designed specifically for automotive and industrial control systems; the D suffix denotes the 14-SOIC surface-mount package rated across the automotive temperature span. Internal frequency compensation means no external compensation components are needed at unity gain, simplifying design-in. Typical applications include automotive sensor interfaces, industrial control loops, transducer amplifiers, active filters, and multi-channel DC signal conditioning in 12 V/24 V systems where the supply range and negative-rail input sensing fit naturally. Design consideration: although the inputs sense down to the negative rail, the output cannot swing fully to the rail - allow roughly 1.5 V of headroom on VCC, or use a rail-to-rail output amplifier for low-side signal chains. This page adds value beyond the datasheet by consolidating drop-in alternatives, application guidance, and comparison data for the LM2902DT in one place.

RFQ Contact
LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi
LM2902DTB

LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi

The onsemi LM2902DTB is a general-purpose quad operational amplifier packaged in a 14-pin TSSOP. It supports a 3 V to 26 V supply range and integrates four amplifier channels, allowing one compact device to implement four independent analog signal-conditioning paths. The LM2902 family is designed for low-cost single-supply equipment where true differential inputs and common-mode operation are useful. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The quad configuration belongs to the hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. True differential inputs allow the amplifier to respond to two input signals rather than requiring both signals to be referenced to ground, making the device useful in sensor, transducer, and feedback networks. The LM2902 family combines a 3 V to 26 V supply range with low quiescent-current operation and a 1.2 MHz unity-gain bandwidth. Its input offset voltage is specified at 2 mV, while the four-channel architecture reduces the number of packages and board-area requirements compared with four separate single amplifiers. These characteristics suit general-purpose analog designs where cost, supply flexibility, and practical integration matter more than precision or rail-to-rail performance. Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or feedback element in a control loop. The device does not reach the positive or negative supply rail at its output, so analog output ranges must be checked against the selected supply voltage and load. Input common-mode range, output swing, input bias current, and noise remain important constraints when precision or high-impedance source designs are required. Typical uses include industrial sensor interfaces, low-cost instrumentation, audio preamplifier stages, active filtering, relay-driver signal conditioning, and general-purpose control boards. A four-channel implementation is especially attractive when several sensors require similar conditioning or when a system needs independent amplifier channels for measurement, monitoring, and feedback. PCB implementation should follow the manufacturer pinout and recommended decoupling guidance. Place the supply bypass capacitor close to the power pins, route sensitive input and feedback traces away from switching nodes, and use a common ground plane with short return paths. Because the outputs cannot swing fully to either rail, applications needing rail-to-rail operation require a different amplifier family. This page combines the LM2902DTB package and supply information with engineering-focused application guidance, replacement criteria, and a parameter comparison. These details help engineers determine when the quad topology simplifies a design and where a single, rail-to-rail, or higher-precision amplifier is the better choice.

RFQ Contact
LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi
LM2902DTBG

LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi

The onsemi LM2902DTBG is a single-supply quad operational amplifier with four amplifiers, a 3 V to 26 V operating supply range, and a 14-pin TSSOP package. It supports true differential inputs and operation from -40 °C to +105 °C, making it suitable for general-purpose industrial signal-conditioning and control circuits. An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output to amplify the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Its differential input architecture supports common signal-conditioning uses such as buffers, amplifiers, comparators, instrumentation stages, and active-feedback circuits. The principal benefits of the LM2902DTBG are its four independent amplifier channels, single-supply operation from 3 V to 26 V, and low-power design characteristics. Four channels in one package can reduce board area in designs that need several matched general-purpose amplifiers. The broad 3 V to 26 V supply range also permits operation from conventional 5 V and 12 V rails as well as higher industrial supply levels that remain below the device rating. The device is based on the established LM324-family architecture, which uses true differential inputs. According to onsemi documentation, the LM324 series is designed for low-cost, general-purpose applications and provides particular advantages in single-supply systems. A unity-gain bandwidth of approximately 1 MHz is suitable for audio-frequency, sensor-interface, feedback-control, and general analog-signal applications rather than high-speed precision instrumentation. Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, comparator functions, industrial control loops, and general-purpose buffering. The four amplifiers can operate independently, although common power rails and package-level thermal behavior should be considered when all channels drive substantial loads. For new layouts, use the manufacturer pin-description table when assigning PCB tracks and preserve the TSSOP-14 land pattern. Check input common-mode range, output swing, input bias current, noise, offset voltage, and slew rate against the actual signal amplitude and frequency before finalizing the circuit. This page combines the LM2902DTBG operating limits, package information, replacement options, and practical circuit-placement guidance into an engineering-focused selection resource for buyers and designers evaluating quad single-supply op amps.

RFQ Contact
LM2902DTBR2 - Quad Op-Amp, 3-26V, 1MHz | onsemi | TSSOP-14
LM2902DTBR2

LM2902DTBR2 - Quad Op-Amp, 3-26V, 1MHz | onsemi | TSSOP-14

The onsemi LM2902DTBR2 is a quad operational amplifier with four independent, internally frequency-compensated op-amp circuits in a 14-pin TSSOP package. It operates from a single supply of 3V to 26V (or dual supplies up to ±13V), offers a 1 MHz bandwidth, and is designed for low-power, general-purpose amplification (per onsemi product listings: 3-26V Quad Low Power, TSSOP). A quad operational amplifier (op-amp) integrates four independent voltage amplifiers on a single silicon die. Each amplifier has a true differential input and can operate from a single power rail, simplifying design in systems that lack negative supplies. Quad op-amps form part of the wider analog signal-chain hierarchy: amplifier IC -> linear IC -> integrated circuit, and they are the workhorse building blocks for signal conditioning, active filtering, buffering, and transducer interface circuits. Key features include the four-circuit integration in a space-saving 14-TSSOP footprint, single-supply operation down to 3V, and the classic LM324-family architecture with true differential inputs. The LM2902 grade is specified for automotive and industrial ambient temperature ranges, distinguishing it from the consumer-grade LM324 by its extended temperature rating and supply conditions. Architecturally, the LM2902 family uses internally compensated bipolar circuitry, which guarantees unity-gain stability without external compensation components and allows outputs to swing close to the negative rail - a signature advantage in single-supply designs where ground-referenced signals must be reproduced. The four amplifiers share one supply pair, reducing board area and BOM count versus four single op-amps. Typical applications include automotive sensor signal conditioning, industrial process control front ends, transducer amplifiers, active filters, summing amplifiers, and multichannel DC gain blocks in battery-powered or 12V/24V-rail systems where the wide 3-26V supply range removes the need for a dedicated regulator. When designing with this device, remember that output swing is limited near the positive rail and the input common-mode range does not include the positive supply; for ground-referenced signals this is usually harmless, but designs requiring rail-to-rail performance should evaluate dedicated rail-to-rail op-amps instead. This page synthesizes distributor availability, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet, offering decision-grade information for sourcing and circuit design in one place.

RFQ Contact
LM2902DTBR2G - 1 MHz Quad Operational Amplifier | onsemi
LM2902DTBR2G

LM2902DTBR2G - 1 MHz Quad Operational Amplifier | onsemi

The onsemi LM2902DTBR2G is a general-purpose quad operational amplifier with four amplifier circuits, 1 MHz gain-bandwidth product, and a 14-pin TSSOP package. It is designed for single-supply operation from 3 V to 32 V, with true differential inputs and an operating temperature range of -40 °C to +105 °C. The LM2902 series combines broad supply-voltage tolerance with low-power operation, making it suitable for general-purpose analog signal conditioning. An operational amplifier is an analog building block that amplifies the voltage difference between its inverting and non-inverting inputs. The quad LM2902 configuration places four independently usable operational amplifiers in one package, reducing board area when a design needs multiple gain stages, buffers, comparators, filters, or instrumentation amplifiers. Within the broader semiconductor hierarchy, this device is a voltage-amplifier IC, an analog amplifier, and ultimately a discrete-component-level signal-conditioning element. The headline features of the LM2902DTBR2G include four amplifier channels, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, true differential inputs, and a wide 3 V to 32 V supply range. Its low-power design is suited to battery-operated and distributed analog systems where four separate amplifier packages would be inconvenient. The 14-pin TSSOP-14 package supports compact surface-mount layouts and is available in a tape-and-reel ordering format. The bipolar amplifier architecture is intended for general-purpose precision rather than high-speed or micropower applications. A 1 MHz gain-bandwidth product makes the device appropriate for low-frequency audio, control, sensing, and signal-conditioning stages. Designers should account for the amplifier's input offset voltage, input bias current, output swing limits, common-mode range, and supply-voltage dependence when defining gain or checking circuit behavior. Typical uses include four-channel sensor conditioning, active filtering, buffer stages for transducers, low-frequency audio amplification, comparators with suitable hysteresis, and general control loops. The quad organization can also simplify instrumentation designs by providing local amplifiers around a sensor or converter. Its broad supply range supports both conventional 5 V and 12 V analog systems and higher rail arrangements where the circuit remains within the device's electrical limits. Design work should begin with the manufacturer's pin-description and electrical-characteristics tables. Place the bypass capacitor close to the supply pins, route sensitive input signals away from switching nodes, and verify output swing, input common-mode range, and stability for the selected gain. Because four channels share one package, thermal performance and power dissipation should be evaluated across the maximum number of simultaneously active amplifiers. This product page combines the LM2902DTBR2G electrical identity, package and application context with engineering-focused comparison information. It also identifies same-footprint alternatives, explains replacement considerations, and highlights practical design checks that help shorten component selection and board-level validation.

RFQ Contact
LM2902EDR2G - Quad Single-Supply Op Amp, 14-SOIC | onsemi
LM2902EDR2G

LM2902EDR2G - Quad Single-Supply Op Amp, 14-SOIC | onsemi

The onsemi LM2902EDR2G is a single-supply quad operational amplifier that integrates four independent, general-purpose amplifiers into a 14-pin SOIC (PDSO-14) surface-mount package, with input offset voltage specified up to 7000 uV. It is designed for general-purpose signal conditioning, filtering and control tasks on low-voltage rails. A quad operational amplifier is a multi-channel analog building block in which four voltage amplifiers share a common package and power supply. Each channel offers inverting and non-inverting inputs and a single output. The quad configuration lets one part provide four amplifier functions - instrumentation gain stages, active filters, comparators, level shifters or buffer stages - while cutting board area, reducing the number of supply pins and lowering per-channel cost. In the analog signal chain, a quad op amp sits between sensors and converters, inside the family of amplifier ICs and linear analog ICs. Key characteristics of the LM2902EDR2G include four amplifier circuits in one package, a maximum input offset voltage of 7000 uV, single-supply operation, and a low-power general-purpose architecture suited to instrumentation and control designs. The 14-pin SOIC footprint is a widely supported package with good thermal performance, adequate creepage and clearance for 36 V-class class parts, and compatibility with automated assembly and standard SOIC sockets. Internally, the device uses the classic bipolar single-supply topology that has made the LM2902 family a long-lived industry standard: a differential input stage driving a push-pull output stage, with internal compensation that allows stable operation as a unity-gain buffer. Because it is a general-purpose amplifier rather than a precision or rail-to-rail part, the design engineer should treat the input common-mode range, output swing and offset as application-dependent limits rather than rail-to-rail capabilities. Typical applications include transducer and sensor signal conditioning, active low-pass and band-pass filters, motor and actuator control loops, audio pre-amplification in consumer equipment, 4-20 mA loop instrumentation, and general microcontroller analog front ends where a quad amplifier saves board space. When designing around this device, confirm the common-mode input range and output swing against your actual supply voltage, and keep the layout symmetrical so that thermal gradients do not create offset mismatch between the four channels. Decouple each supply pin locally with a short, low-inductance path to the ground plane, and route feedback components away from noisy digital return paths. This page brings together the manufacturer datasheet details, a qualified drop-in alternative set with verified package compatibility, and application-specific design notes that go beyond the parameter table.

RFQ Contact
LM2902HDT - Quad 30V Low-Power Op Amp | STMicroelectronics
LM2902HDT

LM2902HDT - Quad 30V Low-Power Op Amp | STMicroelectronics

STMicroelectronics LM2902HDT is a quad operational amplifier built for automotive and industrial control systems, with four independent high-gain, internally frequency-compensated amplifiers in a 14-SO package. It operates from a single supply, supports high-voltage operation up to 30 V, and is designed for low-power signal-conditioning applications. The four amplifiers share the same package while remaining electrically independent, allowing one device to implement multiple analog stages. An operational amplifier is an active analog circuit component that amplifies the difference between two input voltages. The LM2902 belongs to the low-power quad operational amplifier family, which sits within the broader voltage-amplifier and amplifier IC hierarchy. Its single-supply architecture is useful for industrial controls, sensor interfaces, transducers, and general-purpose signal processing where a grounded signal reference is required. The key characteristics are a 30 V maximum supply voltage, low-power operation, four amplifiers per package, and internally compensated operation. The device is intended for low-frequency analog applications rather than high-speed signal chains. Because each amplifier is independent, unused sections can be evaluated according to the manufacturer's recommended input and output conditions. Stable operation requires attention to common-mode range, output swing, input bias current, and supply bypass capacitance. The LM2902HDT is associated with the automotive and industrial control market. Its quad-channel construction can reduce board area when a design needs four similar amplifier functions, such as sensor conditioning, current-loop buffering, threshold comparison, or actuator-driver interfaces. The 14-SO package is a conventional surface-mount solution that is straightforward to route, although the exposed thermal behavior and maximum supply rating must be respected. Typical applications include industrial sensor interfaces, automotive control modules, instrumentation, low-frequency active filters, and buffered control signals. When designing around the LM2902HDT, place the supply bypass capacitor close to the device and confirm that input and output voltages remain inside the common-mode and output-swing limits for the selected supply voltage. Decoupling, grounding, input protection, and stable reference design determine whether the amplifier operates predictably in the final system.

RFQ Contact
LM2902KAVMPWREP - 30V Quad Op Amp | Texas Instruments
LM2902KAVMPWREP

LM2902KAVMPWREP - 30V Quad Op Amp | Texas Instruments

The Texas Instruments LM2902KAVMPWREP is a four-circuit general-purpose operational amplifier designed for single-supply operation from 5 V to 30 V. Each amplifier provides a typical gain-bandwidth product of 1.2 MHz, a typical slew rate of 0.5 V/µs, and a typical input offset voltage of 2 mV. The device is packaged in a 14-pin TSSOP and is rated for operation from -55°C to +125°C. An operational amplifier, commonly abbreviated op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. Four independent amplifiers share a common power supply within one package, allowing one IC to provide multiple analog signal-chain functions. Within the product hierarchy, this device is a quad operational amplifier, a multi-amplifier IC, and a general-purpose analog signal-conditioning component. The LM2902KAVMPWREP combines a wide 30 V supply capability with four independent, internally frequency-compensated amplifiers. Its 1.2 MHz gain-bandwidth product supports moderate-bandwidth signal processing, while the 0.5 V/µs slew rate provides adequate response for audio-frequency, transducer, and general control applications. The low 2 mV typical offset voltage helps reduce output error in DC-coupled amplifier stages. Improved ESD protection rated at 2 kV is a defining feature of the enhanced-product LM2902KAV family. The four amplifiers can operate from a single 5 V to 30 V supply, or from split supplies when the negative supply remains within the device rating. Internal frequency compensation allows each amplifier to operate as a stable closed-loop stage without external compensation components. Typical uses include industrial sensor conditioning, low-level audio amplification, current-loop interfaces, active filtering, comparators, and four-channel control systems. The extended -55°C to +125°C temperature range makes the device suitable for industrial and high-temperature equipment when combined with appropriate passive components and PCB design practices. When designing a circuit, account for input common-mode range, output swing, load current, and stability at the selected gain. Place input and output decoupling capacitors close to the supply pins, keep feedback paths short, and verify noise behavior with the actual source impedance and surrounding circuitry. This product page combines the manufacturer’s core electrical and environmental specifications with practical PCB guidance, direct replacement options, and application-focused engineering analysis for engineers evaluating the LM2902KAVMPWREP.

RFQ Contact
LM2902KAVQDR - 30V Quad Op Amp with 2kV ESD | Texas Instruments
LM2902KAVQDR

LM2902KAVQDR - 30V Quad Op Amp with 2kV ESD | Texas Instruments

The Texas Instruments LM2902KAVQDR is a quad general-purpose operational amplifier rated for 30 V operation, featuring 1.2 MHz gain-bandwidth product, 2 mV input offset voltage, and improved 2 kV ESD protection. The device is packaged in a 14-pin SOIC package and operates from -40 °C to +125 °C. It provides four amplifiers in one package for signal conditioning, buffering, filtering, and general analog signal-chain applications. An operational amplifier is an active analog semiconductor that uses high open-loop gain to amplify voltage differences between its inverting and non-inverting inputs. The LM2902 belongs to the general-purpose operational-amplifier hierarchy, which is widely used in industrial controls, sensor interfaces, audio equipment, power-supply monitoring, and embedded analog systems. Its four independent channels make it useful when a board needs several similar low-speed analog functions without using four separate packages. The key features of the LM2902KAVQDR include a wide 3 V to 32 V supply range, a 1.2 MHz typical gain-bandwidth product, 0.5 V/µs slew rate, and approximately 1.4 mA supply current per amplifier. The KAV version includes improved ESD protection rated at 2 kV, making it suitable for applications where exposed connector pins or external wiring can introduce electrostatic discharge. The 2 mV input offset voltage is suitable for general-purpose signal conditioning rather than precision instrumentation applications. The LM2902KAVQDR is based on a bipolar operational-amplifier architecture. Its four channels are designed for operation from a single supply or from split dual supplies. With a 30 V maximum supply rating, the amplifier can process signals in industrial and automotive-related circuits when the system transient and ESD requirements are controlled appropriately. The 1.2 MHz bandwidth is appropriate for low-frequency audio, control, sensor, and feedback applications rather than high-speed signal processing. Typical applications include sensor signal conditioning, transducer amplification, active filtering, voltage comparison, audio preamplification, current-sense feedback, and general-purpose power-supply control. Because the device is a four-channel amplifier, board designers can use one SOIC-14 package for multiple analog functions while reducing component count and simplifying PCB layout. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be handled according to the manufacturer’s recommended configuration. This page combines the LM2902KAVQDR operating details, package information, practical design guidance, and verified drop-in alternatives to support component selection and board-level implementation.

RFQ Contact
LM2902KAVQDRG4 - 30V Quad Op Amp | Texas Instruments
LM2902KAVQDRG4

LM2902KAVQDRG4 - 30V Quad Op Amp | Texas Instruments

The Texas Instruments LM2902KAVQDRG4 is a four-channel, general-purpose operational amplifier designed for single-supply or split-supply operation, with a 3 V to 30 V supply range, 1.2 MHz gain-bandwidth product, 2 mV input offset voltage, and 0.5 V/µs slew rate in a 14-pin SOIC package. The device provides four independent, internally compensated amplifiers for signal conditioning, buffering, and analog control applications. An operational amplifier is a high-gain analog building block that compares its inverting and non-inverting inputs and drives its output toward the voltage required to reduce the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within amplifier ICs, analog signal-processing ICs, and semiconductor components. Its four independent channels allow multiple analog functions to be implemented in one package, reducing board area and simplifying component inventory. Key characteristics include a 1.2 MHz gain-bandwidth product for moderate-frequency signal processing, a 0.5 V/µs slew rate for changing output waveforms, and a 2 mV input offset voltage. The manufacturer identifies the automotive-qualified LM2902KAV family with improved ESD protection of 2 kV. These characteristics make the amplifier suitable for industrial controls, automotive electronics, sensor interfaces, power-supply control loops, and general-purpose analog signal conditioning. The four amplifiers are frequency compensated and intended for operation from a single supply or split supplies. This allows the same device to process signals referenced to ground or signals centered around a midpoint created by two supply rails. Independent channels can perform amplification, filtering, comparisons, level shifting, current-voltage conversion, or feedback functions without coupling between the amplifiers, provided each channel respects the common supply and grounding limits. Typical applications include conditioning resistive sensor signals, buffering outputs from transducers, amplifying low-frequency control signals, supporting feedback networks in power converters, driving analog inputs in industrial equipment, and implementing multiple amplifier channels in automotive electronic modules. The 30 V supply capability provides useful headroom for industrial and automotive environments, while the 14-pin SOIC package supports conventional surface-mount assembly and inspection. When laying out a circuit, keep each input and feedback path short, connect bypassing capacitors close to the supply pins, and route return currents without sharing narrow paths with sensitive signals. Confirm output swing, input common-mode range, stability, and thermal conditions for the intended supply voltage before using the device in a new design. The manufacturer datasheet remains the controlling reference for limits and test conditions. This product page combines the exact ordering information, key electrical characteristics, package details, application guidance, design notes, and qualified drop-in alternatives for LM2902KAVQDRG4. It also distinguishes automotive-qualified choices from electrically similar family members so engineers can make a replacement decision without treating every similar quad amplifier as automatically interchangeable.

RFQ Contact
LM2902KAVQDRG4Q1 - Quad 26V Op Amp | Texas Instruments
LM2902KAVQDRG4Q1

LM2902KAVQDRG4Q1 - Quad 26V Op Amp | Texas Instruments

The Texas Instruments LM2902KAVQDRG4Q1 is a four-circuit operational amplifier in a 14-pin SOIC package, with a maximum supply voltage of 26 V, 1.2 MHz gain-bandwidth product, and 2 mV offset voltage. The device is AEC-Q100 qualified for automotive applications and supports operation from -55°C to 125°C. An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2902KAVQDRG4Q1 belongs to the operational amplifier hierarchy: amplifier IC, analog amplifier, voltage-feedback operational amplifier, and power-management-adjacent signal-conditioning IC. Four independent amplifiers are integrated into one package, allowing a circuit to use several gain stages, buffers, filters, or comparators without requiring four separate packages. Key characteristics include a 1.2 MHz gain-bandwidth product, 2 mV nominal offset voltage, 80 dB common-mode rejection, and a slew rate of 0.5 V/µs. According to the Texas Instruments LM2902KAV product information, the family is stable at unity gain and does not exhibit phase reversal under overdrive conditions. These characteristics suit general-purpose signal conditioning, low-to-moderate-frequency analog processing, sensor interfaces, and industrial or automotive control systems. The quad amplifier uses a conventional 14-pin SOIC arrangement, with separate input and output pins for four amplifiers and shared power connections. Its wide supply-voltage capability provides headroom for industrial and automotive systems, while the 1.2 MHz bandwidth favors stable, conventional feedback designs rather than demanding high-speed signal-path applications. Unity-gain stability also permits direct buffering without adding a compensation network. Typical uses include transducer-signal conditioning, current-loop receivers, analog sensor amplification, active filtering, DC motor-control support circuits, and general-purpose automotive electronics. In an instrumentation application, the amplifier can convert a small sensor voltage into a larger voltage suitable for an ADC. In a filter, its bandwidth and slew rate determine the achievable signal rate and response. Designers should verify input common-mode range, output swing, load capacitance, and stability for each concrete circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer recommendations rather than left floating. The automotive qualification makes this orderable variant appropriate for harsh-temperature electronics when its specified operating limits are respected.

RFQ Contact
LM2902KAVQDRQ1 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KAVQDRQ1

LM2902KAVQDRQ1 - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KAVQDRQ1 is a four-circuit, general-purpose operational amplifier specified for a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage in a 14-pin SOIC package. The automotive-qualified LM2902-Q1 family is designed for systems requiring four amplifiers per package, extended-temperature operation, and reliable operation across a wide supply range. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902 contains four independent, internally compensated amplifiers, allowing one package to provide feedback control, buffering, signal conditioning, or differential-to-single-ended conversion. In the power-management hierarchy, it is an analog signal-chain IC rather than a voltage regulator, although its wide supply tolerance makes it useful in industrial and automotive power systems. The headline specifications include four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 0.5 V/us slew rate, and approximately 2 mV offset voltage. The device also provides a typical common-mode rejection ratio of 80 dB and an input bias current of 20 nA. Its 30 V operating capability suits 12 V automotive systems, industrial control equipment, audio electronics, and instrumentation while allowing operation from lower single-supply voltages. Each amplifier is frequency compensated and optimized for general-purpose analog design rather than high-speed differential signaling. A 1.2 MHz gain-bandwidth product is most useful at moderate closed-loop gains, while the 0.5 V/us slew rate limits large-signal response at low frequencies. The four independent channels can be configured independently for noninverting, inverting, comparator-like, summing, and feedback-amplifier circuits, subject to common-mode and output-swing limitations. Typical uses include automotive sensor interfaces, battery-powered monitoring equipment, active filters, audio preamplifiers, industrial transducers, and general-purpose control loops. Four amplifiers in one SOIC-14 package reduce board area and component count when several low-frequency analog channels are required. The automotive qualification makes the LM2902-Q1 family especially suitable for body electronics, actuator interfaces, and vehicle sensing systems. Design with the supply voltage, input common-mode range, output swing, input bias current, and capacitive-load drive in mind. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept away from switching nodes. Because the gain-bandwidth and slew-rate limits are modest, verify stability with the intended feedback network and load capacitance before scaling the design into production. This page combines manufacturer specifications, lifecycle information, application guidance, and same-footprint alternatives. It also provides practical design notes and parameter comparisons that help engineers distinguish functionally similar LM2902 variants and choose a suitable replacement without assuming that every ordering code is electrically identical.

RFQ Contact
LM2902KAVQPWR - 30V Quad Op Amp with 2kV ESD | Texas Instruments
LM2902KAVQPWR

LM2902KAVQPWR - 30V Quad Op Amp with 2kV ESD | Texas Instruments

The Texas Instruments LM2902KAVQPWR is a quad, general-purpose operational amplifier built for single, dual, and split-supply operation. The device provides four amplifiers in a 14-pin TSSOP package, operates at 1.2 MHz gain-bandwidth, and offers 2 mV input offset voltage. The K suffix adds 2 kV human-body-model ESD protection, while the wide supply range supports industrial and automotive control systems operating from 3 V to 36 V. An operational amplifier, or op amp, is a high-gain differential-input amplifier that uses external feedback to set closed-loop gain. The LM2902KAV family belongs to the broader hierarchy of analog amplifiers, analog signal-processing ICs, and semiconductors. Four independent amplifiers in one package reduce component count and board area in designs that require multiple sensing, buffering, or gain stages. Key electrical characteristics include a 1.2 MHz gain-bandwidth product, 2 mV maximum input offset voltage for the BA version, 600 uV typical offset stated for the family, and 2 kV ESD protection on the K-suffix devices. The LM2902 supply arrangement supports 26 V single-supply operation or plus-and-minus 13 V dual-supply operation. Supply-current drain is specified as low as 0.8 mA typical and remains independent of supply voltage. The common-mode input voltage range includes ground, making the amplifier suitable for single-supply sensors whose outputs remain near 0 V. Differential input voltage capability and rail-to-rail output behavior also make the device useful in cost-sensitive analog signal chains where the output must approach supply limits. The B-generation device is positioned by Texas Instruments as a drop-in replacement for LM224, LM324, and LM2902 versions with improved specifications. Typical uses include industrial sensor conditioning, transducer amplification, low-frequency active filters, instrumentation amplifiers, audio preamplifier stages, motor-feedback networks, and general-purpose power-control loops. Four amplifiers can implement a complete low-speed control or measurement chain in a single package. PCB design should prioritize short feedback traces, clean grounding, and input-node protection from switching or high-energy sources. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be tied to a defined common-mode voltage rather than left floating. The 14-TSSOP package uses a narrow lead pitch, so inspect the manufacturer land pattern and solder reflow profile before assembly.

RFQ Contact
LM2902KAVQPWREP - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KAVQPWREP

LM2902KAVQPWREP - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KAVQPWREP is a four-circuit operational amplifier rated for 26 V operation, with a 1.2 MHz gain-bandwidth product, 2 mV input-offset voltage, and improved 2 kV ESD protection. The device is packaged in a 14-pin TSSOP (PW) and supports an operating temperature range of -40°C to 125°C. An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and drives its output to reflect their difference. The quad LM2902 family contains four independent, internally frequency-compensated amplifiers, allowing one package to serve multiple analog channels. Within the broader hierarchy, this is an operational amplifier within analog amplifier ICs and semiconductor signal-conditioning devices. The headline characteristics support precision and general-purpose signal conditioning at a 1.2 MHz gain-bandwidth product. A 2 mV input-offset voltage is useful in sensor interfaces, buffer stages, and feedback networks requiring low offset. Improved 2 kV ESD protection adds robustness on exposed circuit boards, while the four-amplifier configuration reduces package count in designs requiring several independent analog channels. Each amplifier is designed to operate from a single supply or from split supplies. The V-suffix family supports operation where the difference between split supplies is 3 V to 32 V, subject to the stated supply limits. Internal frequency compensation allows each amplifier to operate as a voltage follower without an external compensation network. The common-emitter, differential-input architecture supports feedback-based gain and filtering implementations across industrial, instrumentation, and control applications. Typical uses include low-frequency sensor conditioning, transducer amplification, active filtering, voltage buffering, current-loop interfaces, and general control-signal processing. The four independent circuits can also be assigned to unrelated channels on the same board, provided each amplifier observes the applicable common-mode and output-swing limits. Industrial equipment, data-acquisition modules, and embedded measurement systems benefit from combining four channels in one compact package. Design the circuit around the -40°C to 125°C temperature range and the 26 V maximum supply rating. Keep input and feedback paths short, provide stable reference and feedback nodes, and verify output swing at the intended load. Do not assume rail-to-rail operation; confirm the input common-mode range and output-current capability against the circuit requirements before production release. This product page brings together the manufacturer’s device characteristics, package details, verified commercial sourcing links, application guidance, and practical engineering considerations. It also distinguishes the enhanced-product LM2902KAVQPWREP from lower-temperature or different-package family members, helping designers select a replacement without overlooking temperature rating, footprint, or supply constraints.

RFQ Contact