Products (44,000+)

LM2902KAVQPWRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KAVQPWRG4

LM2902KAVQPWRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KAVQPWRG4 is a four-circuit operational amplifier in a 14-pin TSSOP (PW) package. The device supports supply voltages up to 30 V, operates across a 1.2 MHz gain-bandwidth product, and provides a 2 mV input offset voltage. Its four amplifiers are designed for general-purpose analog signal conditioning across industrial, automotive, and instrumentation systems. An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. A quad operational amplifier combines four amplifiers in one package, allowing a board to implement four independent gain, buffering, filtering, comparison, or current-voltage conversion functions while reducing package count and simplifying power distribution. The LM2902KAV family provides a 3 V to 36 V supply range, a 1.2 MHz gain-bandwidth product, and input offset voltage as low as 2 mV in the BA version. The target MPN is associated with improved ESD protection of 2 kV and automotive qualification for AEC-Q100 applications. The 14-pin TSSOP package also supports operation from -40°C to +125°C. Each amplifier contains differential input and output stages with substantial open-loop gain. When feedback is applied, the closed-loop gain is established by external resistors rather than by the intrinsic open-loop gain. Suitable external compensation and output bypassing must be selected according to the operating mode, load, and gain because stability requirements vary with circuit topology. Typical uses include current-sensing amplifiers, sensor signal conditioning, low-frequency active filters, level-shift and reference buffers, industrial sensor interfaces, and automotive control modules. The four independent channels also reduce board area when several low-frequency analog functions are required near one another. For layout, keep input and feedback connections short, place compensation or bypass components close to their associated pins, and avoid routing high-current or switching signals alongside sensitive input traces. Confirm common-mode and output-swing limits at the actual supply voltage, and verify stability with the intended load and cable capacitance before production release. This page organizes the manufacturer specifications, package information, application guidance, and same-footprint ordering alternatives into one engineering reference. It also highlights where automotive qualification and ESD protection affect replacement decisions, helping designers distinguish genuine board-level drop-ins from merely similar quad operational amplifiers.

RFQ Contact
LM2902KAVQPWRG4Q1 - Quad 30V Automotive Op Amp | TI
LM2902KAVQPWRG4Q1

LM2902KAVQPWRG4Q1 - Quad 30V Automotive Op Amp | TI

Texas Instruments LM2902KAVQPWRG4Q1 is a four-circuit general-purpose operational amplifier designed for automotive and industrial equipment. It combines a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 mV input-offset-voltage rating, 0.5 V/µs slew rate, and 2 kV ESD protection in a 14-pin TSSOP package. The four amplifiers are independent and frequency compensated, allowing one package to implement multiple analog signal-conditioning stages without requiring four separate devices. An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. Within the larger semiconductor hierarchy, this device belongs to the operational-amplifier family, analog IC category, and signal-conditioning ecosystem. Its wide supply range, low supply-current drain, and common-mode input capability make it suitable for circuits that must operate from single or split supplies across demanding temperature environments. The LM2902KAVQPWRG4Q1 provides a 1.2 MHz gain-bandwidth product for general-purpose closed-loop amplification. Its 0.5 V/µs slew rate supports moderate-frequency signal changes, while 2 mV input offset voltage limits systematic input-referred error. The K-suffix device adds 2 kV ESD protection, and the Q1 grade supports automotive qualification requirements. A typical supply-current drain of 0.8 mA per amplifier also helps limit consumption in multi-amplifier signal chains. Each internal amplifier is independently compensated and operates from a single supply or from split supplies when the total supply span permits operation. The device maintains low-voltage behavior and remains usable across a wide common-mode input range. Input differential voltages greater than 0.5 V should not be applied continuously because they can cause input-offset-voltage shift beyond the specified maximum, with the magnitude increasing as ambient temperature rises. Typical uses include automotive sensor conditioning, transducer amplification, active filtering, voltage buffering, differential sensing, and low-frequency closed-loop control loops. Four independent amplifiers can reduce package count when a circuit needs multiple stages, such as an instrumentation front end combining input conditioning, gain, filtering, and output buffering. Design layouts should reserve clean return paths for each amplifier, place input and output components near their associated pins, and avoid long parallel traces that can increase noise pickup. Check supply decoupling, output loading, common-mode headroom, and stability before finalizing the circuit. Because a quad device contains four amplifiers, verify every channel’s gain-bandwidth and stability configuration rather than assuming every stage has identical loading. This page consolidates the manufacturer’s electrical ratings, automotive-ordering information, package details, application guidance, comparison data, and practical PCB considerations into a design-focused reference for engineers evaluating the LM2902KAVQPWRG4Q1 and its pin-compatible family option.

RFQ Contact
LM2902KAVQPWRQ1 - 30V Quad AEC-Q100 Op Amp | TI
LM2902KAVQPWRQ1

LM2902KAVQPWRQ1 - 30V Quad AEC-Q100 Op Amp | TI

Texas Instruments LM2902KAVQPWRQ1 is a four-circuit bipolar operational amplifier designed for automotive applications, with a 3 V to 32 V supply range, 1.2 MHz gain-bandwidth product, 2 mV offset voltage, and a 14-pin TSSOP package. The device provides four independent amplifiers in one package, making it suitable for signal conditioning, sensing, buffering, and control circuits where component count and board area are important. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The quad operational-amplifier category combines four amplifiers in one package, while the broader hierarchy includes voltage-feedback amplifiers, analog amplifiers, and integrated circuits. This makes the LM2902KAVQPWRQ1 useful wherever several low-to-moderate-bandwidth analog channels must operate from the same supply. Automotive qualification is a defining feature of the LM2902-Q1 family. According to the Texas Instruments LM2902-Q1 product information, the LM2902-Q1, LM2902B-Q1, and LM2902BA-Q1 devices are qualified in accordance with AEC-Q100 specifications. Other key characteristics include 2 kV improved ESD capability, a 0.5 V/µs slew rate, and an input common-mode voltage range that includes ground. The latter supports practical single-supply designs when the signal remains near the lower supply rail. The KAV version combines the standard bipolar amplifier architecture with 1.2 MHz gain-bandwidth performance and 2 mV offset voltage. Its four amplifier sections share the positive and negative supply pins, while each section retains its own input and output terminals. A gain-bandwidth product near 1.2 MHz supports general-purpose closed-loop operation well below the amplifier's upper frequency limit, depending on feedback topology and acceptable phase margin. Typical uses include automotive sensor interfaces, low-frequency active filters, transimpedance amplifiers, audio signal conditioning, battery monitoring, actuator drivers, and general analog control loops. The 14-pin TSSOP package reduces board footprint relative to four separate single or dual amplifier packages. Tape-and-reel packaging supports automated assembly, while the automotive qualification supports designs subject to rigorous reliability requirements. When designing around the LM2902KAVQPWRQ1, verify the complete input and output voltage limits under temperature and load conditions. Keep sensitive input traces away from switching nodes and provide local supply bypassing near the package. Account for output swing, slew-rate limits, input common-mode range, and stable feedback components when selecting gain and compensation values. This product page combines the manufacturer’s automotive qualification information with package, pinout, application, and replacement guidance. It also organizes drop-in alternatives by package and measured parameter differences, helping engineers compare upgrade paths before committing a PCB design.

RFQ Contact
LM2902KD - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KD

LM2902KD - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KD is a quad general-purpose operational amplifier in a 14-pin SOIC package. Each of its four amplifiers supports a maximum supply voltage of 26 V, operates at a typical gain-bandwidth product of 1.2 MHz, and includes improved electrostatic-discharge protection rated to 2 kV. The device is designed for industrial and general-purpose analog signal-conditioning circuits that require four amplifiers in one package. An operational amplifier is a voltage-amplifying component whose open-loop gain is controlled by external feedback. In a closed-loop circuit, negative feedback establishes the actual gain and improves linearity, while the internal architecture provides high input impedance and low output impedance. The LM2902KD belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors, combining four amplifier channels in one package to reduce board area and simplify multi-channel designs. Key characteristics include four amplifier circuits, a 26 V maximum supply rating, a 1.2 MHz typical gain-bandwidth product, and 2 kV improved ESD protection. The listed input offset voltage is typically 3 mV, while typical input offset current is 2 nA. Typical supply-current drain is 0.8 mA per amplifier. These specifications make the device suitable for sensor interfaces, low-frequency signal conditioning, active filters, and industrial control applications where a robust, economical quad amplifier is preferred. The LM2902 family uses internal frequency compensation, allowing operation as a unity-gain amplifier without external compensation components. Its common-mode input voltage range includes ground, which supports direct sensing of low-side signals near the lower rail. This characteristic is useful in battery-powered, transducer, and grounded-source systems where the input signal can approach the supply floor. Typical applications include four-channel sensor conditioning, process-control instrumentation, current-loop receivers, audio preamplifier stages, active filters, and general buffer or gain stages. Because the device is specified for a 26 V maximum supply, it should not be treated as a 36 V part even though closely related LM2902B-family devices may support a wider supply range. Designers should verify common-mode range, output swing, input bias behavior, and channel-to-channel variation against the exact operating conditions. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer’s stability recommendations rather than left with floating inputs. This page organizes the LM2902KD electrical characteristics, package information, application guidance, verified source links, and documented drop-in alternatives for faster engineering selection. Use the manufacturer datasheet and pin-description table for final PCB routing, input/output assignment, and production-limit decisions.

RFQ Contact
LM2902KDB - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KDB

LM2902KDB - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KDB is a quad general-purpose operational amplifier with four amplifiers, a 26 V supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection. The device is offered in a 14-pin SSOP (DB) package for industrial, consumer, and automotive applications. An operational amplifier is a voltage-amplifying circuit whose open-loop gain is controlled by negative feedback. Operational amplifiers belong to the analog IC hierarchy and support precision control, signal conditioning, buffering, current-to-voltage conversion, and closed-loop circuit functions. The LM2902K combines four general-purpose amplifiers in one package, reducing component count and simplifying multi-channel analog boards. Key characteristics include four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 kV improved ESD protection, and an operating temperature range from -40°C to 125°C. Typical input offset voltage is 3 mV, typical input offset current is 2 nA, and typical supply-current drain is 0.8 mA. The common-mode input range includes ground, allowing the amplifier to process signals close to the lower supply rail. The LM2902K belongs to the improved LM2902B generation. According to the Texas Instruments product documentation, the LM324B and LM2902B families can replace earlier LM224, LM324, and LM2902 versions while preserving the familiar quad-amplifier architecture. The B generation emphasizes improved electrical characteristics and stronger ESD protection compared with legacy devices. Typical applications include industrial control and instrumentation, sensor signal conditioning, transducer amplification, low-frequency active filters, audio preamplification, buffer stages, and general-purpose analog interfaces. The internal frequency compensation supports straightforward closed-loop operation in amplifier, comparator, and follower configurations when operating within the device's common-mode and output-voltage limits. The most important layout consideration is stable decoupling. Place a supply-bypass capacitor close to the positive and ground pins, maintain short return paths, and avoid long traces around high-impedance inputs. Verify output-current, input common-mode range, output swing, and ambient-temperature limits for each channel because the four amplifiers share package power and thermal constraints. This product page combines the LM2902KDB operating characteristics, drop-in alternatives, application guidance, comparison parameters, and practical design notes in one engineering reference. Use the Texas Instruments LM2902K documentation as the controlling source for final electrical limits, pin assignments, ordering information, and PCB land patterns.

RFQ Contact
LM2902KDBR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM2902KDBR

LM2902KDBR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

Texas Instruments LM2902KDBR is a quad general-purpose operational amplifier with four amplifiers, a 26 V supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection. The device is offered in a 14-pin SSOP (DB) package for industrial, consumer, and automotive applications. An operational amplifier is a voltage-amplifying circuit whose open-loop gain is controlled by negative feedback. Operational amplifiers belong to the analog IC hierarchy and support precision control, signal conditioning, buffering, current-to-voltage conversion, and closed-loop circuit functions. The LM2902K combines four general-purpose amplifiers in one package, reducing component count and simplifying multi-channel analog boards. Key characteristics include four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 kV improved ESD protection, and an operating temperature range from -40°C to 125°C. Typical input offset voltage is 3 mV, typical input offset current is 2 nA, and typical supply-current drain is 0.8 mA. The common-mode input range includes ground, allowing the amplifier to process signals close to the lower supply rail. The LM2902K belongs to the improved LM2902B generation. According to the Texas Instruments product documentation, the LM324B and LM2902B families can replace earlier LM224, LM324, and LM2902 versions while preserving the familiar quad-amplifier architecture. The B generation emphasizes improved electrical characteristics and stronger ESD protection compared with legacy devices. Typical applications include industrial control and instrumentation, sensor signal conditioning, transducer amplification, low-frequency active filters, audio preamplification, buffer stages, and general-purpose analog interfaces. The internal frequency compensation supports straightforward closed-loop operation in amplifier, comparator, and follower configurations when operating within the device's common-mode and output-voltage limits. The most important layout consideration is stable decoupling. Place a supply-bypass capacitor close to the positive and ground pins, maintain short return paths, and avoid long traces around high-impedance inputs. Verify output-current, input common-mode range, output swing, and ambient-temperature limits for each channel because the four amplifiers share package power and thermal constraints. This product page combines the LM2902KDBR operating characteristics, drop-in alternatives, application guidance, comparison parameters, and practical design notes in one engineering reference. Use the Texas Instruments LM2902K documentation as the controlling source for final electrical limits, pin assignments, ordering information, and PCB land patterns.

RFQ Contact
LM2902KDBRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KDBRE4

LM2902KDBRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KDBRE4 is a four-circuit general-purpose operational amplifier with a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and a 2 mV maximum input offset voltage. The device is supplied in a 14-pin SSOP package configured for tape-and-reel handling. It combines four independent amplifiers with internal frequency compensation, making it suitable for general analog signal conditioning, voltage buffering, amplification, and feedback-controlled applications. An operational amplifier, commonly called an op amp, is a high-gain differential-input amplifier whose external feedback network determines its closed-loop behavior. Within the broader semiconductor hierarchy, an op amp is a linear integrated circuit used for voltage amplification, current-to-voltage conversion, filtering, comparison, and buffering. The LM2902 combines four such amplifier channels in one package, reducing board area compared with four separately packaged devices. The principal characteristics include operation from dual supplies of up to ±13 V, a 26 V total supply rating, a 1.2 MHz gain-bandwidth product, and input offset voltage specified at 2 mV for the LM2902 product family. A typical input offset voltage of 3 mV and typical input offset current of 2 nA are also identified. The common-mode input range includes ground, allowing direct sensing near the lower supply rail, while the low input bias and offset parameters support precision low-frequency signal conditioning. Each channel uses internal frequency compensation, removing the need for an external compensation capacitor in ordinary closed-loop configurations. The design includes ESD protection characterized as less than 500 V using the MIL-STD-883 Method 3015 procedure and greater than 200 V using the machine model. The manufacturer also identifies the LM2902 as qualified for automotive applications under AEC-Q100, with customer-specific configuration control and major-change approval support. Typical uses include sensor-signal conditioning, transducer amplification, analog control loops, audio preamplification, bridge-balancing networks, and low-frequency active filters. Four integrated channels can reduce component count in designs requiring several matched general-purpose amplifier functions. Common-mode input voltage that includes ground makes the device useful in circuits powered from positive-only supplies where the signal approaches zero volts. Design with adequate supply bypass capacitance and route input and output traces to minimize parasitic coupling. Confirm common-mode, output-swing, and input-bias requirements against the load and supply conditions. Because a linear amplifier dissipates power proportional to supply voltage and output current, thermal analysis remains important when driving low-impedance loads or operating at elevated ambient temperature. This product page combines manufacturer specifications, package and ordering information, verified source links, application guidance, and practical replacement considerations. It supports faster component evaluation while directing engineers to the manufacturer datasheet for final pin assignments, limiting values, test conditions, and qualification details.

RFQ Contact
LM2902KDBRG4 - 26V Quad Op Amp | Texas Instruments
LM2902KDBRG4

LM2902KDBRG4 - 26V Quad Op Amp | Texas Instruments

The Texas Instruments LM2902KDBRG4 is a quad general-purpose operational amplifier designed for a 3 V to 26 V supply, with output current up to 60 mA per channel and a gain-bandwidth product of 1.2 MHz. The device is housed in a 14-pin SSOP package with an operating temperature range of -40°C to +125°C. Each amplifier provides a unity-gain bandwidth of 1.2 MHz, a slew rate of 0.5 V/μs and a typical open-loop gain of 50 dB. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902K belongs to the operational-amplifier hierarchy, which sits under analog amplifiers and integrated circuits. Its four independent channels make it practical where a design needs several comparators, buffers, transimpedance stages or low-frequency feedback amplifiers without using four separate packages. The principal performance features include a 0.5 μA typical input bias current, 20 nA typical input offset current, a typical differential input resistance of 2 MΩ and a common-mode input range extending to approximately 0.5 V below the positive supply rail. The amplifier also supports rail-to-rail output swing under suitable load conditions, although its input common-mode range is not rail-to-rail. The LM2902K architecture uses a classic general-purpose design with an internal bias stage and an output stage capable of sourcing or sinking 60 mA per channel. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-conditioning, control-loop and general analog signal-processing tasks, but it is not intended for high-speed data acquisition or precision millivolt-level instrumentation. Typical uses include four-channel sensor interfaces, low-cost audio mixing and filtering, industrial control signal conditioning, current-to-voltage conversion with external resistors, and comparator-style threshold detection. The wide 26 V maximum supply rating also supports 24 V industrial systems, provided signal amplitudes remain inside the input common-mode range and output current stays below the channel limit. When laying out a circuit, place the bypass capacitor close to the positive supply pin, route the ground return directly to the ground pin, and keep sensitive input traces away from output and supply nodes. Decoupling resistance can create gain peaking near the 1.2 MHz crossover region, so feedback-network values should be selected with the amplifier's gain-bandwidth behavior in mind.

RFQ Contact
LM2902KDG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KDG4

LM2902KDG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KDG4 is a general-purpose quad operational amplifier with four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection. The device is supplied in a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, in body width. Each channel provides the standard differential-input, single-ended-output operational-amplifier arrangement. An operational amplifier is an analog integrated circuit that compares voltages applied to its inverting and non-inverting inputs and produces an output voltage representing that difference. When negative feedback surrounds the amplifier, it forms the core building block of voltage amplifiers, current buffers, comparators, filters, integrators, and sensor-conditioning circuits. The LM2902K places four such channels in one package, allowing a compact design to handle several independent low-frequency analog signals. The quad configuration provides four channels, 26 V maximum supply voltage, and 1.2 MHz gain-bandwidth product. These characteristics make the LM2902KDG4 suitable for general-purpose signal conditioning where the required signal bandwidth is below the amplifier's 1.2 MHz unity-gain capability. Its 2 kV improved ESD capability provides additional protection against electrostatic discharge encountered during handling or installation. The 14-SOIC construction is appropriate for conventional through-hole board assembly because the leads extend from the sides of the package. A quad package also reduces the number of amplifier packages required when a design needs four channels. Channel assignment and electrical behavior should be confirmed against the manufacturer pin-description table before PCB routing, particularly for power pins, input pins, and output pins. Typical uses include audio preamplification, instrumentation-signal conditioning, active filtering, transducer amplification, analog control loops, and general sensor interfaces. In a typical application, the LM2902KDG4 can amplify a low-level sensor signal, buffer an analog source, or implement an active filter with external resistors and capacitors. Common-mode range, input bias current, output swing, and stability requirements must be checked against the actual circuit. A key design consideration is power-supply bypassing. Place the required bypass capacitors close to the supply pins and route the ground return directly to the device ground. Avoid long analog traces, maintain a stable reference for each feedback network, and verify that the selected feedback and compensation values support the intended closed-loop bandwidth at the 1.2 MHz gain-bandwidth product. This product record combines the exact ordering information for LM2902KDG4 with package identification, lifecycle context, verified manufacturer characteristics, sourcing guidance, and engineering-oriented comparison information. It helps designers distinguish the discontinued orderable variant from related LM2902K products while focusing attention on the electrical and PCB implications of replacement.

RFQ Contact
LM2902KDR - 26V 1.2MHz Quad Op Amp | Texas Instruments
LM2902KDR

LM2902KDR - 26V 1.2MHz Quad Op Amp | Texas Instruments

The Texas Instruments LM2902KDR is a quad general-purpose operational amplifier designed for single- and dual-supply operation, with four amplifiers in a 14-pin SOIC package. Key characteristics include a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and improved ESD tolerance of 2 kV. The device operates from -40°C to +125°C, making it suitable for industrial, automotive, and general-purpose analog signal-conditioning systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The LM2902KDR contains four such amplifiers in one package, allowing a design to implement multiple gain stages, buffers, comparators, or active filters without using separate packages. In the broader electronics hierarchy, it belongs to the amplifier IC and general-purpose operational amplifier families, providing a practical combination of wide supply-voltage tolerance, low cost, and circuit versatility. The device provides input-offset voltage and drift characteristics suitable for precision-enough general-purpose feedback networks, common-mode input range, output swing capability, and short-circuit-safe outputs. Its 1.2 MHz gain-bandwidth product supports low-frequency signal amplification and applications including sensor conditioning, active filtering, voltage buffering, and audio or control-signal interfaces. Improved ESD protection of 2 kV increases robustness in exposed connector and industrial environments, although normal handling precautions remain necessary. Each amplifier uses standard complementary differential inputs and an output stage capable of driving common external loads within its specified output-swing limits. Designers should preserve adequate input/output voltage headroom from the supply rails and account for input bias-current effects when using high source impedances. Decoupling capacitors should be placed close to the supply pins, while sensitive analog inputs should be routed away from switching nodes and high-current return paths. Typical uses include four-channel sensor interfaces, industrial control modules, audio preamplifier stages, active low-pass filters, motor and actuator signal conditioning, and general dual-supply analog circuits. The four amplifiers can be used independently, so unused channels should be configured according to the manufacturer's recommendations rather than left floating. This approach prevents unintended oscillation and reduces sensitivity to stray pickup. A critical layout consideration is to separate the four high-impedance input paths from power-converter switches and digital return currents. When driving a capacitive load, add an isolation resistor close to the amplifier output and verify stability on the assembled board. The 14-pin SOIC footprint supports conventional leaded-assembly processes, while its wide temperature range supports demanding industrial environments. This product overview connects the LM2902KDR's four-channel architecture, 26 V supply capability, 1.2 MHz bandwidth, 2 kV ESD rating, and temperature range with practical placement guidance, pin-compatible alternatives, and selection criteria for general-purpose analog designs.

RFQ Contact
LM2902KNS - 26V Quad 1.2MHz Op Amp | Texas Instruments
LM2902KNS

LM2902KNS - 26V Quad 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KNS is a quad general-purpose operational amplifier designed for a 26 V maximum supply voltage, with a 1.2 MHz gain-bandwidth product and improved 2 kV ESD protection. The device is packaged in a 14-SOIC package measuring 0.209 inch, or 5.30 mm, wide. Four independent amplifiers are integrated into one package, making the LM2902KNS suitable for analog signal conditioning, sensor interfaces, feedback networks, and general instrumentation. An operational amplifier is a voltage amplifier with very high open-loop gain, allowing it to amplify small signals when used with external negative feedback. A quad operational amplifier contains four amplifier sections in one package, providing a convenient way to implement several analog functions while reducing the number of components on a circuit board. The LM2902K belongs to the broader operational-amplifier category, which is part of the linear and analog semiconductor hierarchy. Key characteristics include four amplifier channels, a 1.2 MHz gain-bandwidth product, 26 V maximum supply capability, 20 nA input bias current, 80 dB open-loop gain, and approximately 0.5 uA quiescent current. The improved 2 kV ESD rating provides additional device protection in applications where exposed handling or connector-connected signals may introduce electrostatic transients. The 14-SOIC package is a conventional surface-mount package suited to conventional PCB assembly methods. The LM2902KNS is intended for general-purpose analog applications rather than precision or high-speed signal-chain work. Its 1.2 MHz bandwidth is appropriate for audio-frequency, control, and instrumentation circuits where moderate operating speed and wide supply-voltage tolerance are more important than very high slew rate or extremely low offset voltage. The 26 V supply capability also makes it useful in circuits operating from higher-voltage industrial rails, provided the amplifier inputs and outputs remain within their permitted common-mode and output ranges. Typical uses include four-channel sensor amplification, voltage buffering, active filtering, differential sensing, comparator-style threshold conditioning, and general feedback control. In a multi-amplifier design, the common package helps keep channel-to-channel placement compact, although each amplifier should still be evaluated for output-current capability, load impedance, stability, and noise performance in its intended circuit. Designers should review the manufacturer datasheet for the complete electrical characteristics, recommended operating conditions, input and output limits, and package details. Decoupling capacitors should be placed close to the supply pins, unused amplifier sections should be configured according to the datasheet guidance, and input and output signals should not exceed the specified common-mode and output-voltage limits. This page summarizes the principal LM2902KNS characteristics and identifies drop-in alternatives with the same 14-SOIC footprint for engineering evaluation. The information on this page combines the manufacturer product identification, distributor package and inventory descriptions, and cross-reference findings for LM2902KNS. It is intended to help engineers narrow the component choice, verify the package, and plan a replacement strategy before completing detailed circuit validation.

RFQ Contact
LM2902KNSG4 - Quad 26V 1.2MHz Op-Amp SOIC-14 | Texas Instruments
LM2902KNSG4

LM2902KNSG4 - Quad 26V 1.2MHz Op-Amp SOIC-14 | Texas Instruments

The Texas Instruments LM2902KNSG4 is a quad general-purpose operational amplifier with four independent high-gain, internally frequency-compensated amplifier circuits in a 14-pin SOIC (NS) package rated for a 26 V single supply or dual supplies, delivering a 1.2 MHz gain-bandwidth product. An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of analog signal conditioning. Quad op-amps such as the LM2902K family integrate four such amplifiers on one die, sharing supply rails to reduce board area and cost in multi-channel analog front ends, within the broader hierarchy of linear ICs and analog signal processing semiconductors. Key features of the LM2902KNSG4 include wide supply ranges of 3 V to 26 V single-supply (or +/-13 V dual supply per the LM2902K family data), a low supply-current drain of typically 0.8 mA that is largely independent of supply voltage, and an input common-mode range that extends to ground on single supplies. The K-grade device improves on the base LM2902 with enhanced 2 kV ESD robustness, which the manufacturer lists on the TI LM2902K product page. Technically, the device uses internally compensated bipolar architecture providing unity-gain stability without external compensation components. The 0.5 V/µs slew rate and 1.2 MHz gain-bandwidth product suit low-to-moderate frequency conditioning: sensor buffering, active filters, comparators, and transducer amplifiers. Differential input voltage ranges and the ability to swing outputs near the negative rail support ground-referenced sensing on single-supply industrial rails. Typical applications include industrial process-control signal conditioning, automotive sensor interfaces within the -40C to +125C automotive temperature range of the LM2902 family, and consumer audio or instrumentation multi-channel buffers where four matched amplifiers reduce BOM count. One design consideration: output swing is limited near the positive rail, so set signal headroom below the supply by roughly 1.5 V, or use rail-to-rail output alternatives if full-swing is required. Decouple the shared VCC pin with 0.1 µF close to pin 4. This page adds value beyond the datasheet with drop-in alternatives, a parameter-by-parameter comparison table, and practical design notes synthesized for engineers evaluating the LM2902KNSG4.

RFQ Contact
LM2902KNSR - 26V Quad 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM2902KNSR

LM2902KNSR - 26V Quad 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM2902KNSR is a quad general-purpose operational amplifier designed for a 26 V maximum supply voltage, with a 1.2 MHz gain-bandwidth product and improved 2 kV ESD protection. The device is packaged in a 14-SOIC package measuring 0.209 inch, or 5.30 mm, wide. Four independent amplifiers are integrated into one package, making the LM2902KNSR suitable for analog signal conditioning, sensor interfaces, feedback networks, and general instrumentation. An operational amplifier is a voltage amplifier with very high open-loop gain, allowing it to amplify small signals when used with external negative feedback. A quad operational amplifier contains four amplifier sections in one package, providing a convenient way to implement several analog functions while reducing the number of components on a circuit board. The LM2902K belongs to the broader operational-amplifier category, which is part of the linear and analog semiconductor hierarchy. Key characteristics include four amplifier channels, a 1.2 MHz gain-bandwidth product, 26 V maximum supply capability, 20 nA input bias current, 80 dB open-loop gain, and approximately 0.5 uA quiescent current. The improved 2 kV ESD rating provides additional device protection in applications where exposed handling or connector-connected signals may introduce electrostatic transients. The 14-SOIC package is a conventional surface-mount package suited to conventional PCB assembly methods. The LM2902KNSR is intended for general-purpose analog applications rather than precision or high-speed signal-chain work. Its 1.2 MHz bandwidth is appropriate for audio-frequency, control, and instrumentation circuits where moderate operating speed and wide supply-voltage tolerance are more important than very high slew rate or extremely low offset voltage. The 26 V supply capability also makes it useful in circuits operating from higher-voltage industrial rails, provided the amplifier inputs and outputs remain within their permitted common-mode and output ranges. Typical uses include four-channel sensor amplification, voltage buffering, active filtering, differential sensing, comparator-style threshold conditioning, and general feedback control. In a multi-amplifier design, the common package helps keep channel-to-channel placement compact, although each amplifier should still be evaluated for output-current capability, load impedance, stability, and noise performance in its intended circuit. Designers should review the manufacturer datasheet for the complete electrical characteristics, recommended operating conditions, input and output limits, and package details. Decoupling capacitors should be placed close to the supply pins, unused amplifier sections should be configured according to the datasheet guidance, and input and output signals should not exceed the specified common-mode and output-voltage limits. This page summarizes the principal LM2902KNSR characteristics and identifies drop-in alternatives with the same 14-SOIC footprint for engineering evaluation. The information on this page combines the manufacturer product identification, distributor package and inventory descriptions, and cross-reference findings for LM2902KNSR. It is intended to help engineers narrow the component choice, verify the package, and plan a replacement strategy before completing detailed circuit validation.

RFQ Contact
LM2902KNSRG4 - 26V Quad 1.2MHz Op Amp | Texas Instruments
LM2902KNSRG4

LM2902KNSRG4 - 26V Quad 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KNSRG4 is a quadruple general-purpose operational amplifier designed for single-supply or split-supply operation, with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and a 14-pin SOIC package. It combines low-noise performance with wide supply-voltage tolerance, making it suitable for industrial, automotive, and general analog signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. In its noninverting configuration it gains a signal applied to the positive input; in its inverting configuration it amplifies the input applied through the feedback network to the negative input. The LM2902K belongs to the hierarchy of operational amplifier, analog amplifier, linear amplifier, and semiconductor, while supporting applications from sensing and filtering to instrumentation and actuator control. Four independent amplifiers are integrated in one 14-pin SOIC, reducing board area compared with four single-amplifier packages. Each channel is frequency compensated and can operate from a single or split supply. According to the Texas Instruments product page, the device is a quad, 26 V, 1.2 MHz operational amplifier with improved 2 kV ESD protection. The four-channel organization is useful when a system requires several similar low-frequency amplification, buffering, or differential-input functions. The LM2902 architecture is intended for dependable, cost-conscious general-purpose analog designs rather than precision or high-speed signal chains. Its 1.2 MHz bandwidth supports moderate-frequency closed-loop operation, while the high-gain internal stages help implement common amplifier topologies. Split-supply operation is particularly useful in bipolar sensor circuits, where signals may be centered around 0 V and require both positive and negative output swing. Typical uses include industrial sensor interfaces, transducer conditioning, loop filtering, audio preamplification, automotive signal processing, and four-channel active filtering. The device can also implement comparators in applications where the response-speed requirements are modest and the input common-mode range is adequate. Each amplifier is independent, allowing unused channels to be configured according to the manufacturer's recommended stability practices. For PCB design, place the device to minimize noise-sensitive input routing and keep feedback traces short. Decoupling capacitors should be positioned close to the supply pins, while input and feedback paths should avoid nearby switching nodes and high-current return paths. Stable operation depends on choosing the correct feedback network and observing the input common-mode and output-swing limits for the selected supply voltage. This page organizes the device specifications, replacement options, application guidance, and practical design notes into a concise engineering reference. It also distinguishes true package-compatible alternatives from merely functional equivalents so replacement decisions can be checked against footprint, pinout, and operating requirements.

RFQ Contact
LM2902KPW - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KPW

LM2902KPW - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KPW is a quad general-purpose operational amplifier packaged in a 14-pin TSSOP. It contains four independent, high-gain, internally frequency-compensated amplifiers designed for single-supply operation over a 26 V maximum supply range, with a 1.2 MHz gain-bandwidth product and improved 2 kV ESD protection. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between input signals. The LM2902 belongs to the general-purpose amplifier family, combining voltage amplification, buffering, filtering, and signal-conditioning functions in one package. Its four amplifiers make it useful where several independent analog channels are required without using four separate packages. The LM2902KPW provides a wide supply-voltage operating range, a 1.2 MHz gain-bandwidth product, and four amplifier circuits in one 14-pin TSSOP. The improved ESD rating of 2 kV is relevant in industrial and consumer equipment where handling transients or exposed connector inputs can affect an analog interface. The device is identified as a standard, general-purpose amplifier rather than a precision or low-noise amplifier. Its internally compensated architecture simplifies closed-loop design because no external compensation network is required for typical voltage-feedback configurations. The 1.2 MHz bandwidth supports general-purpose signal amplification and moderate-frequency active filtering, while the wide supply range permits operation from conventional single supplies or higher industrial rails. Designers should still verify input and output common-mode limits, output swing, and stability against the final circuit topology. Typical uses include sensor signal conditioning, industrial control loops, audio preamplification, low-frequency active filters, instrumentation interfaces, and general analog signal chains. Using four amplifiers in one package can also reduce PCB area and simplify design reviews compared with separate single-amplifier packages, although shared package limitations should be considered for applications requiring independent thermal or fault isolation. For a new design, keep the TSSOP footprint and pin assignments of the LM2902KPW unchanged, provide adequate input and output bypassing, and verify the selected bias point against the operating voltage and signal range. The manufacturer product page and datasheet are the appropriate references for ordering information, electrical limits, pin functions, and qualification details.

RFQ Contact
LM2902KPWE4 - Quad 1.2MHz Op Amp, 26V, 14-TSSOP | Texas Instruments
LM2902KPWE4

LM2902KPWE4 - Quad 1.2MHz Op Amp, 26V, 14-TSSOP | Texas Instruments

The Texas Instruments LM2902KPWE4 is a quadruple general-purpose operational amplifier with a 1.2 MHz gain-bandwidth product, a 26 V maximum supply rating, and four independent amplifiers in a 14-pin TSSOP (PW) surface-mount package. An operational amplifier is a voltage-gain building block that amplifies the difference between two input voltages. A quad device packages four amplifiers sharing one supply pin and one ground pin, which cuts board area roughly in half compared with four single amplifiers and keeps sensitive analog channels on a common reference. Quad op amps sit in the hierarchy above single and dual amplifiers and below application-specific amplifiers, and they belong to the broader class of analog signal-conditioning integrated circuits used in nearly every industrial, automotive, and instrumentation design. Key features of the LM2902KPWE4 include a 1.2 MHz gain-bandwidth product that supports operation from DC to several hundred kHz of closed-loop bandwidth, a 26 V maximum total supply voltage for wide input swing, and improved ESD protection rated to 2 kV per the Texas Instruments LM2902K family description. The part is qualified to AEC-Q100 for automotive applications, and the E4 orderable suffix denotes the RoHS-compliant, lead-free finish. The 14-TSSOP body measures 0.173 inch (4.40 mm) wide, so the part fits the same footprint as other TI quad op amps such as the LM2902KPW. Architecturally the LM2902K family is a classic bipolar general-purpose amplifier stage with internal biasing, designed for single or dual supply operation and for driving typical resistive and capacitive loads within the output swing limits. Because it is a general-purpose part rather than a rail-to-rail precision amplifier, design work must confirm that the input common-mode range and output swing are adequate for the signal chain in question, and that the amplifier is stable with the output load capacitance present on the board. Typical uses include sensor signal conditioning, transducer and bridge-amplifier front ends, audio mixer sub-circuits, industrial loop-current receivers, and general instrumentation where four channels of gain are needed on a single board. Two channels can also be cross-coupled to build a higher-gain stage or an instrumentation-style front end. One key design consideration is that a 26 V supply capability does not mean the amplifier should be operated near 26 V: supply noise, output stage distortion, and device stress all rise as the rail voltage increases. Keep the supply within the intended range and decouple close to the supply pins with a 0.1 uF ceramic plus a bulk capacitor. This page brings together the manufacturer ordering information, drop-in replacement options in the same TSSOP-14 footprint, and applied design guidance for layout, decoupling, and stability that goes beyond the basic ordering table.

RFQ Contact
LM2902KPWR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM2902KPWR

LM2902KPWR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM2902KPWR is a quad general-purpose operational amplifier packaged in a 14-pin TSSOP. It contains four independent, high-gain, internally frequency-compensated amplifiers designed for single-supply operation over a 26 V maximum supply range, with a 1.2 MHz gain-bandwidth product and improved 2 kV ESD protection. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between input signals. The LM2902 belongs to the general-purpose amplifier family, combining voltage amplification, buffering, filtering, and signal-conditioning functions in one package. Its four amplifiers make it useful where several independent analog channels are required without using four separate packages. The LM2902KPWR provides a wide supply-voltage operating range, a 1.2 MHz gain-bandwidth product, and four amplifier circuits in one 14-pin TSSOP. The improved ESD rating of 2 kV is relevant in industrial and consumer equipment where handling transients or exposed connector inputs can affect an analog interface. The device is identified as a standard, general-purpose amplifier rather than a precision or low-noise amplifier. Its internally compensated architecture simplifies closed-loop design because no external compensation network is required for typical voltage-feedback configurations. The 1.2 MHz bandwidth supports general-purpose signal amplification and moderate-frequency active filtering, while the wide supply range permits operation from conventional single supplies or higher industrial rails. Designers should still verify input and output common-mode limits, output swing, and stability against the final circuit topology. Typical uses include sensor signal conditioning, industrial control loops, audio preamplification, low-frequency active filters, instrumentation interfaces, and general analog signal chains. Using four amplifiers in one package can also reduce PCB area and simplify design reviews compared with separate single-amplifier packages, although shared package limitations should be considered for applications requiring independent thermal or fault isolation. For a new design, keep the TSSOP footprint and pin assignments of the LM2902KPWR unchanged, provide adequate input and output bypassing, and verify the selected bias point against the operating voltage and signal range. The manufacturer product page and datasheet are the appropriate references for ordering information, electrical limits, pin functions, and qualification details.

RFQ Contact
LM2902KVQDR - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KVQDR

LM2902KVQDR - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KVQDR is a quad general-purpose operational amplifier with four independent amplifiers, a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection in a 14-pin SOIC package. It is designed for single-supply or split-supply operation over a -40°C to 125°C temperature range. An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses high open-loop gain to amplify the difference between two input voltages. The quad operational-amplifier category combines four amplifiers in one package, reducing board area compared with four separate single amplifiers. LM2902-family devices belong to the broader operational-amplifier, analog-signal, and semiconductor hierarchies. The LM2902KVQDR provides four independent, internally frequency-compensated amplifiers with a 1.2 MHz gain-bandwidth product. Its 30 V supply capability supports higher-voltage industrial and instrumentation circuits than the 26 V LM2902K family. Improved 2 kV ESD protection adds robustness when exposed to electrostatic discharge during handling or operation. The quad configuration is useful for amplifier arrays, sensor interfaces, active filters, and differential signal-conditioning channels. Operation from a single supply allows the input and output signals to remain close to ground, while split-supply operation supports bipolar signals around a midpoint. Each amplifier can be configured independently for noninverting, inverting, summing, comparator-style, or feedback-amplifier applications. The 14-pin SOIC package supports conventional surface-mount assembly and broad compatibility with industrial control and analog-instrumentation designs. Typical applications include four-channel sensor conditioning, active low-pass and band-pass filters, bridge-signal amplifiers, differential measurement front ends, audio preamplifier blocks, and general-purpose analog signal chains. The four-amplifier architecture is particularly useful when several channels require similar conditioning without allocating separate packages. When designing around the LM2902KVQDR, verify input and output common-mode limits across the complete supply range and use stable compensation for capacitive loads. Place input and feedback components close to their associated pins to reduce parasitic capacitance and preserve the expected 1.2 MHz bandwidth. This page combines the manufacturer device description, technical characteristics, package information, qualified drop-in alternatives, and practical design guidance for engineers evaluating the LM2902KVQDR in multi-channel analog systems.

RFQ Contact
LM2902KVQDRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KVQDRG4

LM2902KVQDRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KVQDRG4 is a general-purpose quad operational amplifier with four independent amplifier channels, a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection. The device is packaged in a 14-pin SOIC (D) and is specified for operation from -40°C to 125°C. Its combination of four amplifiers, wide supply capability, and low cost makes it suitable for space-constrained analog signal-conditioning systems. An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. Within the broader semiconductor hierarchy, the LM2902KV is an amplifier IC, a linear operational amplifier, and a general-purpose precision signal-conditioning component. Multiple amplifiers can process independent channels or be configured together for instrumentation, filtering, buffering, comparison, or gain-control functions. The key operating characteristics include a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. The input bias current is listed as low as 20 nA. Improved 2 kV ESD protection helps improve tolerance of electrostatic discharge encountered during handling or field use. The automotive-qualified grade is identified for automotive applications, while the extended 125°C upper operating temperature supports industrial and automotive environments. The LM2902KV architecture uses four independent operational-amplifier channels in one package, reducing board area compared with four separate single or dual amplifier packages. Because each channel can operate from the same supply rails, the device can support common-mode input ranges close to the supply limits and can be used with single or split-supply arrangements, subject to the detailed operating limits in the manufacturer datasheet. Typical applications include current-loop and voltage-loop signal conditioning, industrial sensor interfaces, automotive electronics, audio and communication equipment, active filtering, transducers, and general-purpose analog boards. The quad arrangement is particularly useful when four similar channels are required, such as in four-channel sensor acquisition, comparator-style threshold circuits, or multiple amplifier stages distributed across one assembly. PCB design should account for input bias currents, output drive capability, supply decoupling, and the stability of each feedback network. Place the supply bypass capacitor close to the device supply pins, route sensitive input and feedback traces away from switching nodes, and use resistive networks that preserve the amplifier's intended bias-current balance. The 14-pin SOIC footprint simplifies hand assembly and automated surface-mount production. This page combines the exact device identity, verified technical characteristics, application guidance, drop-in alternatives, and package-focused design considerations to support component selection and PCB planning. It also distinguishes directly interchangeable 14-pin parts from options that require closer electrical review.

RFQ Contact
LM2902KVQDRG4Q1 - Quad 30V 1.2MHz Op Amp, AEC-Q100 | Texas Instruments
LM2902KVQDRG4Q1

LM2902KVQDRG4Q1 - Quad 30V 1.2MHz Op Amp, AEC-Q100 | Texas Instruments

The Texas Instruments LM2902KVQDRG4Q1 is a quadruple general-purpose operational amplifier designed for 30 V supply operation, delivering a 1.2 MHz gain-bandwidth product, a 0.5 V/us slew rate and 80 dB common-mode rejection, packaged in a 14-pin SOIC (PDSO14, MS-012AB) body and qualified to AEC-Q100 for automotive applications. An operational amplifier, or op amp, is a voltage-gain building block that compares two input terminals and drives its output to amplify the difference between them. A quad op amp such as the LM2902KVQDRG4Q1 integrates four independent amplifier channels in one package. In the product taxonomy it sits at the bottom of the chain: quad operational amplifier -> operational amplifier -> voltage amplifier -> analog amplifier IC -> integrated circuit -> semiconductor. Because the four channels share one package, the LM2902KVQDRG4Q1 replaces four discrete single amplifiers and simplifies both BOM cost and board routing. Key features include a maximum input offset voltage of 10,000 uV (10 mV), 1.2 MHz unity-gain bandwidth, 0.5 V/us slew rate, 80 dB CMRR and an input bias current in the 0.5 uA class. The device operates from a 5 V minimum supply up to the 30 V class, so it accepts both conventional 5 V logic-era rails and industrial or automotive 24 V buses. Extended temperature performance reaches -55 C to +125 C, and the plastic body is marked as green (lead-free). Improved ESD handling adds robustness: the device withstands less than 500 V per MIL-STD-883, Method 3015 and exceeds 200 V using the machine model. Architecturally, the LM2902KVQDRG4Q1 uses a classic voltage-feedback differential input stage with a class-AB complementary output stage, which is why the output can swing close to the supply rails without the crossover distortion of a rail-to-rail design. It is intended for single-supply operation from 5 V up, so output swing limits and input common-mode range should be checked against the actual rail. Noise, offset and CMRR figures are specified over the full -55 C to +125 C range rather than only at room temperature, which matters in automotive and industrial environments. Typical applications include automotive sensor and body electronics signal conditioning, industrial 24 V control panel interface circuits, audio preamplifier and mixer stages, current-loop instrumentation, power-supply feedback loops and general-purpose buffer and gain stages where four channels are needed on a single board. When designing around this amplifier, remember that it is not rail-to-rail input or output. Keep input common-mode voltage inside the specified range, verify the output swing at the lowest supply voltage you use, and place 100 nF ceramic decoupling close to the V+ and V- pins to avoid supply-noise coupling into the gain stage. This page brings together the manufacturer specifications, AEC-Q100 and ESD details, pin-level function mapping, drop-in alternatives in the same SOIC-14 footprint, and practical decoupling and thermal guidance that are not consolidated in a single manufacturer datasheet.

RFQ Contact
LM2902KVQDRQ1 - 26V Quad Automotive Op Amp | Texas Instruments
LM2902KVQDRQ1

LM2902KVQDRQ1 - 26V Quad Automotive Op Amp | Texas Instruments

The Texas Instruments LM2902KVQDRQ1 is a four-channel, general-purpose operational amplifier designed for automotive applications in a 14-pin SOIC package. It supports supply voltages up to 26 V, operates from a single supply or split supplies, provides a gain-bandwidth product of 1.2 MHz, and has an input offset voltage of 2 mV. Each of its four amplifier channels is independent and internally frequency compensated, allowing multiple analog signal-conditioning stages to share one package. An operational amplifier is a high-gain, differential-input analog IC commonly used in sensor interfaces, buffer stages, error amplifiers, and low-frequency closed-loop control circuits. The LM2902-Q1 belongs to the operational-amplifier hierarchy, where quad operational amplifiers integrate four amplifiers into one IC while preserving independent signal paths. Its automotive qualification makes it suitable for electronic control units, body systems, instrumentation, and other 12 V vehicle platforms where operating-temperature robustness and supply-voltage tolerance are important. The device combines a 1.2 MHz gain-bandwidth product with a typical slew rate of 0.5 V/µs and a common-mode rejection ratio of 80 dB. Its 2 mV input offset specification supports accurate amplification of low-level signals, while the four-channel configuration reduces package count on analog-conditioning boards. The 26 V maximum supply rating provides additional input-voltage margin in automotive systems that operate from a 12 V battery through transient and filtering networks. Internally, each amplifier stage provides high open-loop gain and frequency compensation, allowing stable operation without an external compensation capacitor in ordinary closed-loop configurations. The amplifier can operate from a single positive supply or from split positive and negative supplies. Input bias current of approximately -0.5 µA and the stated CMRR characterize the input stage, helping engineers evaluate source-impedance matching and common-mode noise rejection before selecting external resistor networks. Typical uses include automotive sensor interfaces, battery monitoring, active filtering, actuator-signal conditioning, instrumentation amplifiers, and general-purpose analog control loops. The four channels can independently implement gain stages, buffers, comparators using suitable feedback arrangements, or voltage followers. Its SOIC-14 format supports conventional surface-mount assembly while providing enough pins for the four conventional dual-input amplifier channels and the two supply terminals. Design around the 26 V supply limit, maintain the required common-mode and output-voltage ranges, and account for input bias current when using high-source-impedance sensors. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Verify startup, shutdown, capacitive-load stability, and thermal performance in the final automotive environment rather than relying only on nominal amplifier parameters. This page combines the exact orderable MPN, automotive-family positioning, pin-level implementation guidance, drop-in comparison data, and application-focused design guidance to support faster component evaluation and PCB-level planning.

RFQ Contact
LM2902KVQPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KVQPWR

LM2902KVQPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KVQPWR is a four-circuit general-purpose operational amplifier rated for up to 30 V, with a 1.2 MHz gain-bandwidth product, improved 2 kV ESD protection, and operation from -40°C to 125°C. The device is packaged in a 14-pin TSSOP (PW) package and is intended for industrial and general-purpose analog signal-conditioning designs. An operational amplifier, commonly called an op amp, is an analog semiconductor that uses high-gain differential amplification to compare two input voltages and drive an output according to their difference. The LM2902KV belongs to the operational amplifier hierarchy, which includes general-purpose amplifiers, voltage-feedback amplifiers, analog signal-conditioning ICs, and broader semiconductor components. Its four independent amplifiers can support multiple channels within one package. The principal features include a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 kV ESD protection. The four-amplifier configuration reduces board area in designs requiring several independent analog channels. According to the Texas Instruments LM2902KV product page, the KV version provides improved ESD capability while retaining the familiar LM2902-family architecture and extended operation from -40°C to 125°C. The LM2902 family is designed for general-purpose applications where economy, input-voltage range, and multiple channels are more important than precision or high-speed performance. Its relatively wide supply capability makes it suitable for circuits operating from industrial control voltages as well as lower-voltage systems. The 1.2 MHz gain-bandwidth product supports low-frequency signal conditioning, buffering, amplification, summation, filtering, and comparator-style threshold functions when operated with suitable feedback networks. Typical uses include industrial sensor interfaces, transducer signal conditioning, low-frequency active filters, analog summing amplifiers, instrumentation buffers, and general control-system analog channels. Because four amplifiers are integrated in one package, it can also reduce component count in multi-channel sensor, monitoring, and data-acquisition designs where channel-to-channel consistency and compact implementation are beneficial. Designers should account for input common-mode range, output swing, supply headroom, stability with the selected feedback network, input bias current, and the effects of capacitive loading. Decoupling capacitors should be placed close to the supply pins, and sensitive inputs should be routed away from high-current switching nodes. The TSSOP package requires careful assembly practices because its fine lead pitch can increase solder-bridging risk. This product page combines the manufacturer specifications, package details, application guidance, and qualified drop-in comparisons to simplify component selection. It also highlights the distinctions between the original LM2902 variants and the improved LM2902KV device, helping engineers confirm compatibility before changing an existing 14-pin TSSOP design.

RFQ Contact
LM2902KVQPWRG4 - 30V Quad Op Amp | Texas Instruments
LM2902KVQPWRG4

LM2902KVQPWRG4 - 30V Quad Op Amp | Texas Instruments

Texas Instruments LM2902KVQPWRG4 is a quad operational amplifier with a 30 V supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection, housed in a 14-pin TSSOP (PW) package. The device supports operation from -40°C to 125°C and provides four independent, high-gain, frequency-compensated amplifiers for single-supply or split-supply operation. An operational amplifier is a voltage-feedback amplifier used to amplify differential signals and drive high-impedance loads. Within the broader semiconductor hierarchy, this quad device belongs to the operational-amplifier family, analog amplifier IC category, and general-purpose signal-conditioning ecosystem. Four amplifiers in one package reduce board area and simplify designs requiring several independent analog channels. The LM2902KV generation improves electrical characteristics while retaining compatibility with established LM224, LM324, and LM2902 applications. Its 30 V maximum supply rating supports higher-voltage analog systems than conventional 26 V quad op amps. A 1.2 MHz gain-bandwidth product supports general-purpose closed-loop signal processing, while the stated 80 dB common-mode rejection ratio helps suppress output response to common-mode input variation. Improved 2 kV ESD protection strengthens robustness in exposed industrial environments. Each amplifier includes high open-loop gain, differential input capability, and internal frequency compensation. The device can operate from a single supply or from positive and negative rails, making it suitable for bipolar signal conditioning around a zero-volt reference. Its common-mode input range, output swing limits, input-bias current, and input-offset-voltage limits should be checked against the system’s signal levels and supply headroom before finalizing a design. Typical uses include industrial sensor interfaces, low-frequency active filters, transducers, audio preamplifier stages, analog-to-digital converter input conditioning, and general feedback-control circuits. Four independent channels are especially useful when a design needs several filtered or buffered signals and board area is constrained. The 14-pin TSSOP package supports compact surface-mount assemblies while exposing all four amplifier sections. For stable operation, use the manufacturer-recommended bypass capacitors close to the supply pins, maintain adequate output-load capacitance, and verify operation across the complete -40°C to 125°C temperature range. Input and output voltages must remain within the device’s absolute-maximum and common-mode limits. Stable feedback-network design is also essential when operating at higher frequencies or with nonstandard gain settings. This product page organizes the manufacturer’s principal operating limits, package information, pin assignment, verified commercial parameters, and practical design guidance. It also distinguishes the closest same-footprint alternatives by supply rating, precision grade, temperature range, and ESD capability so engineers can make a replacement decision without changing the PCB land pattern.

RFQ Contact
LM2902KVQPWRG4Q1 - Quad 26V Automotive Op Amp | TI
LM2902KVQPWRG4Q1

LM2902KVQPWRG4Q1 - Quad 26V Automotive Op Amp | TI

The Texas Instruments LM2902KVQPWRG4Q1 is an automotive, quad operational amplifier with four amplifiers per package, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage. The device is offered in a 14-pin TSSOP package and is intended for general-purpose analog signal conditioning in automotive systems. Its four independent channels support amplifier, buffer, comparator, summing, and differential-input configurations. An operational amplifier is a voltage-controlled differential amplifier whose high open-loop gain and feedback network create accurate, stable closed-loop behavior. The LM2902 family belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, voltage-feedback amplifiers, analog signal-conditioning ICs, and power-management system components. Four integrated channels reduce package count while preserving separate amplifier sections for sensors, actuator interfaces, diagnostics, and control loops. The headline characteristics are a 26 V supply capability, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage. These ratings support low-frequency control and sensing functions where a wide supply range, multiple channels, and economical integration are more important than high-speed precision. The automotive designation identifies the LM2902-Q1 family as qualified for vehicle applications, although production qualification does not by itself guarantee suitability for every vehicle subsystem. Each amplifier is frequency compensated and intended for use with conventional negative-feedback networks. When configured as a non-inverting amplifier, the closed-loop gain is established by external resistors; when configured as an inverting amplifier, the input and feedback impedances set the signal relationship. The 1.2 MHz gain-bandwidth product leaves useful open-loop bandwidth for common audio-bandwidth, sensor-conditioning, and industrial-control loops, although exact stability and accuracy must be evaluated at the selected gain and load. Typical uses include battery-powered sensor interfaces, vehicle body and chassis control modules, transducer conditioning, line-driver stages, low-current actuator drivers, and general-purpose signal amplification. Operating from a single supply or split supplies allows integration around sensors referenced to ground or to mid-supply. Care should be taken when driving capacitive loads or approaching supply-rail limits because output swing, input common-mode range, load current, and thermal conditions determine usable linear operation. The TSSOP-14 footprint requires a compact surface-mount layout with adequate copper for heat dissipation. Place bypass capacitance close to the supply pins, maintain short feedback paths, and route high-impedance input nodes away from switching nodes. Because this exact orderable code is listed as no longer in production, engineers should verify availability and approved sourcing before releasing a new production design. This product summary combines the automotive LM2902-Q1 specifications with same-footprint family alternatives, application guidance, package considerations, and a selection framework. It helps distinguish electrical and qualification differences that are not apparent from the 14-pin TSSOP package designation alone.

RFQ Contact