Products (44,000+)

LM358APWRG4 - Dual 700 kHz Op Amp | Texas Instruments
LM358APWRG4

LM358APWRG4 - Dual 700 kHz Op Amp | Texas Instruments

The Texas Instruments LM358APWRG4 is a dual general-purpose operational amplifier in an 8-pin TSSOP package. Each amplifier provides a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 80 dB common-mode rejection, and 2 mV input offset voltage, making the device suitable for general signal conditioning from a single 5 V supply. An operational amplifier is an analog amplifier that uses very high open-loop gain to increase the voltage applied across an impedance connected to its inverting input. With external feedback, a practical LM358 stage can operate as a voltage amplifier, current-to-voltage converter, comparator, or active filter. The LM358 family belongs to the broader operational amplifier and analog signal-processing IC categories. The LM358APWRG4 uses a 0.7 mA typical supply-current drain, supports single or dual supplies, and provides a common-mode input range that includes the ground rail. Its 0.3 V/us slew rate limits large-signal bandwidth, while the 80 dB CMRR helps reject common-mode noise. These characteristics make it appropriate for transducers, feedback loops, sensor interfaces, audio paths, and low-to-moderate-frequency control systems. The device operates from 5 V in the characterized operating condition and belongs to the 26 V maximum supply-voltage class of the LM358 family. Its operating temperature range is 0 C to 70 C for this ordering code. The LM358 dual-amplifier configuration allows both channels to share one package while preserving independent inputs and outputs, reducing board area compared with two single-amplifier packages. Common applications include buffering sensor outputs, amplifying low-level signals, summing analog signals, driving ADC input stages, implementing active filters, and providing feedback around analog control loops. Because the LM358 output stage is not rail-to-rail, output swing limits and input common-mode restrictions must be checked against the actual signal range before layout is finalized. Place input, feedback, and bypass capacitors close to their associated pins, and route sensitive input traces away from switching nodes and high-current paths. Verify stability with the manufacturer guidance for capacitive loads, because the 0.3 V/us slew rate and output-capacitance limits can affect transient response. The TSSOP-8 package also requires careful thermal assessment when both channels operate continuously near the supply rail. This page combines the device specifications, verified sourcing records, application engineering guidance, and same-footprint replacement analysis to support faster component selection and PCB planning.

RFQ Contact
LM358AWDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
LM358AWDT

LM358AWDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics LM358AWDT is a low-power dual operational amplifier packaged in an 8-pin SOIC. The device contains two amplifiers, operates from a single supply, and is specified at 1.1 MHz unity-gain bandwidth with a 70°C maximum operating temperature. Its general-purpose design makes it suitable for signal conditioning, buffering, and analog amplification in industrial and embedded systems. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Each amplifier in the dual package can amplify noninverting or inverting signals, while negative feedback defines the closed-loop gain and bandwidth. This makes the device useful where a sensor, divider, comparator, or analog front end needs a higher-current drive than the preceding circuit can provide. The LM358AWDT offers two independent amplifiers in one 8-SOIC package, reducing board area compared with two separate single amplifiers. Its 1.1 MHz bandwidth supports general-purpose signal paths operating well below megahertz data rates. The low-power architecture also makes the device appropriate for battery-operated, test, measurement, and embedded-control equipment, subject to the device-specific limits in the manufacturer datasheet. Operationally, the part combines input, output, and biasing functions within each amplifier section. The output stage must remain within its voltage limits, so designers should provide suitable load current and verify common-mode and output-swing conditions at the actual supply voltage. Feedback components set the gain and bandwidth; choosing resistor and capacitor values consistent with the amplifier’s stable operating region is essential for predictable behavior. Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filtering, bridge or differential signal conditioning, and general feedback control. Two amplifiers in one package can also handle a matched pair of channels when their grounding, decoupling, and signal paths are laid out carefully. The same package size simplifies replacement with compatible SOIC-8 dual operational amplifiers when their electrical ratings and pin functions have been checked. The primary layout consideration is decoupling. Place a suitable supply bypass capacitor close to the power pin, keep the feedback loop compact, and route output and input signals away from the noisy supply and ground-return paths. Avoid using the ground lead as a high-current return for external loads, because resistance in the ground trace can introduce gain error and channel coupling. This product page combines the LM358AWDT ordering information, package identification, operating limits, verified listings, drop-in candidate analysis, and practical implementation guidance. It also highlights where engineers must consult the manufacturer datasheet for detailed pin descriptions, input limits, offset, current, noise, and recommended application circuits before completing a production design.

RFQ Contact
LM358AWPT - Low-Power Dual Op Amp | STMicroelectronics | TSSOP-8
LM358AWPT

LM358AWPT - Low-Power Dual Op Amp | STMicroelectronics | TSSOP-8

The STMicroelectronics LM358AWPT is a low-power, dual operational amplifier packaged in an 8-pin TSSOP. It integrates two general-purpose amplifier channels in one surface-mount package, with a listed output-current capability of 40 mA. The LM358AWPT combines the familiar dual-amplifier organization with a compact power-surface-mount footprint, making it suitable for signal conditioning, buffering, feedback control, and low-frequency analog circuits. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual operational amplifier contains two amplifier sections that share common supply and ground connections but can process separate signals. In the broader semiconductor hierarchy, the LM358 belongs to the operational-amplifier class, then to amplifier ICs, analog ICs, and ultimately the wider integrated-circuit and semiconductor categories. The LM358AWPT is identified by STMicroelectronics as a low-power dual operational amplifier. Its two-circuit configuration reduces component count and board area when two related analog functions must be implemented. The 8-pin TSSOP package supports automated assembly while preserving a compact outline. The listed 40 mA output-current capability also makes the device relevant to designs that require more drive than a minimum-footprint micropower amplifier. Each amplifier section can support common analog signal-processing tasks such as voltage amplification, impedance buffering, comparators, current-sensing interfaces, and active-feedback control. Because the two channels share package-level power pins, their operating supply is common even when they perform unrelated functions. PCB designers should still route input, output, supply, and ground connections carefully to minimize coupling between the two channels and to preserve signal integrity near the device. Typical applications include industrial sensor interfaces, low-voltage control loops, audio and communications equipment, battery-powered instrumentation, and general-purpose analog signal conditioning. In a feedback controller, one channel might amplify a sensor signal while the other buffers a reference or drives an error amplifier. In a sensing circuit, the dual organization can reduce the number of packages needed compared with separate single-channel amplifiers. The principal design consideration is supply compatibility. Confirm the minimum and maximum operating voltages, input common-mode range, output swing, input bias current, noise, slew rate, and stability requirements in the STMicroelectronics manufacturer datasheet before using the device with a selected system rail. Decoupling capacitors, grounding, output-load limits, and any reactive load compensation should follow the application guidance in that datasheet. This product page organizes the LM358AWPT information around verified product identity, package details, directly compatible replacement options, application guidance, and PCB-level design considerations. It also distinguishes exact drop-in candidates from broader LM358 comparisons so that engineers can assess footprint, function, and operating-limit compatibility before authorizing a substitution.

RFQ Contact
LM358AWST - Dual Low-Power Op Amp | STMicroelectronics
LM358AWST

LM358AWST - Dual Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM358AWST is a dual, general-purpose operational amplifier with two amplifier circuits in an 8-pin MiniSO package. The device is identified as a low-power op amp and is intended for general signal-conditioning applications. Its package dimensions, electrical limits, supply range, offset characteristics, and temperature ratings should be confirmed against the STMicroelectronics datasheet before final qualification. An operational amplifier is an active semiconductor device that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and analog signal-chain ICs. Its dual architecture provides two amplifiers in one package, reducing board area while simplifying common power-supply and grounding arrangements. The LM358AWST is specifically identified as a standard, general-purpose amplifier with two circuits. That makes it useful for functions such as voltage buffering, current-to-voltage conversion, sensor conditioning, differential amplification, and basic active filtering. Because it contains two amplifier sections, one package can support two related analog channels or two stages of a larger signal-processing circuit. Its MiniSO-8 form factor supports compact surface-mount PCB construction while exposing two complete amplifier channels. The exposed package area of the MiniSO family also provides a thermal path to the PCB, although actual heat dissipation depends on copper area, adjacent components, ambient temperature, and output drive. Designers should preserve the manufacturer’s recommended pad and land-pattern dimensions rather than treating it as a generic SOIC footprint. Typical uses include industrial sensor interfaces, buffered control signals, low-frequency analog measurement paths, audio preamplifier stages, power-supply monitoring, and general-purpose gain stages. In each case, input common-mode range, output swing, unity-gain stability, noise, and supply requirements must be checked against the circuit’s operating conditions. The LM358AWST is especially relevant where two general-purpose channels are needed without allocating separate single amplifier packages. For a new layout, route input and output traces away from switching nodes and high-current return paths, connect decoupling capacitors close to the supply pins, and verify the complete analog signal range at worst-case supply voltage and temperature. If the PCB revision is fixed, use the pin-description table and land-pattern drawing in the manufacturer datasheet to confirm every connection before substitution or sourcing an equivalent.

RFQ Contact
LM358BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM358BAIDR

LM358BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM358BAIDR is a dual operational amplifier with a 36 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV offset voltage, housed in an 8-SOIC package. The device contains two independent general-purpose amplifiers, making it suitable for signal conditioning, sensing, and control circuits that operate from single or dual supplies. An operational amplifier is an analog signal-processing IC that amplifies the difference between its inverting and non-inverting inputs. The LM358 family belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Unlike a single amplifier package, this dual-device version provides two amplifier channels in one component, reducing board area and simplifying designs that require paired gain, filtering, buffering, or comparison functions. The LM358BAIDR combines a maximum 36 V supply rating with a 1.2 MHz gain-bandwidth product. Its 2 mV offset voltage is suitable for many general-purpose applications where moderate DC accuracy is acceptable. The 8-SOIC surface-mount package supports conventional PCB assembly, while the -40°C to 85°C operating range covers industrial and commercial environments. Typical rail-to-rail behavior, common-mode limits, supply-current requirements, and output-drive capability should be checked against the manufacturer datasheet for each design. The two amplifier sections share the power-supply pins but otherwise provide separate inverting and non-inverting inputs and outputs. This arrangement suits cascaded stages, dual sensor channels, error amplifiers, voltage followers, and differential signal-conditioning circuits. Because both channels use the same device, their offset, bandwidth, noise, and common-mode performance are inherently well matched for many balanced systems. Typical uses include industrial sensor interfaces, buffered control outputs, low-frequency active filters, audio preamplification, power-supply monitoring, and general embedded signal conditioning. It can also support two independent channels in equipment where a quad amplifier would leave unnecessary circuitry. The 1.2 MHz bandwidth is most appropriate for low- and intermediate-frequency signals rather than wideband video or high-speed communications. When laying out the PCB, route sensitive input and feedback traces away from switching nodes and high-current paths. Place input-rejection and output-bypass capacitors close to their corresponding pins, verify common-mode and output-swing limits at the intended supply voltage, and maintain adequate copper area for thermal dissipation. Confirm the exact SOIC-8 land pattern and pin numbering against the manufacturer pin-description table. This product page combines the LM358BAIDR ordering information, manufacturer specifications, package details, price reference, pinout status, and technically filtered replacement guidance. It also adds application-oriented design notes and comparison criteria that help engineers determine whether the original device or a qualified drop-in alternative best fits a new board revision.

RFQ Contact
LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments
LM358BIDGKR

LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments

Texas Instruments LM358BIDGKR is a dual operational amplifier in an 8-pin VSSOP package, built for general-purpose signal conditioning from single or dual power supplies. Its headline electrical ratings are a 36 V maximum supply voltage, 1.2 MHz gain-bandwidth product, and 3 mV maximum input offset voltage. The LM358B family combines two amplifiers in one package and supports input common-mode ranges that extend toward ground, making it useful in industrial, instrumentation, control, and sensor-interface circuits. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category sits above instrumentation amplifiers and buffers in the broader analog-IC hierarchy, while the dual configuration places two independent amplifiers in one compact surface-mount package. LM358B devices are often selected when moderate bandwidth, wide supply-voltage operation, and input-stage tolerance are more important than low-noise precision performance. The LM358BIDGKR provides a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. These values support general-purpose closed-loop signal processing, including voltage buffers, cross-coupled amplifiers, differential stages, integrators, and active filtering. Its 3 V to 36 V operating supply range accommodates common industrial and laboratory supply levels. The manufacturer identifies 300 µV as the typical low offset voltage for the LM358B family, while distributor product information lists 3 mV offset voltage for this ordering code. Because each channel contains an input stage, output stage, and compensation network, LM358B behavior depends on supply voltage, load, output voltage, and common-mode input level. The 1.2 MHz gain-bandwidth product makes the device suitable for moderate-frequency closed-loop gains rather than precision or high-speed applications. Users should account for output-current limits and ensure that the amplifier is not used to source or sink current beyond its specified operating conditions. Typical uses include 0–10 V industrial sensor interfaces, audio preamplifier and mixing stages, active analog filters, motor and actuator control loops, low-frequency data acquisition, and general sensor conditioning. In a single-supply system, the input common-mode range extending to ground helps process signals centered near 0 V, provided the output swing and input limits are checked against the actual supply voltage. For PCB design, keep input and feedback traces short, route output signals away from high-impedance inputs, and provide stable bypass capacitance close to the supply pins. Check output drive into the intended load and leave adequate headroom for input and output swing. Decoupling placement and trace geometry can matter more than nominal amplifier bandwidth when working with long routes or high source impedances. This page combines manufacturer specifications, ordering information, pin-package details, qualified same-family alternatives, and application guidance for faster component selection and board-level planning. It also highlights the practical distinction between the LM358B family's typical offset voltage and the ordering-code maximum used for design margin.

RFQ Contact
LM358BIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM358BIDR

LM358BIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM358BIDR is a dual general-purpose operational amplifier with two amplifier channels, a 36 V maximum supply rating, 1.2 MHz gain-bandwidth performance, and 3 mV output offset voltage. The device is offered in an 8-pin SOIC package, making it suitable for conventional surface-mount analog signal-conditioning boards. The LM358 name identifies an industry-standard dual-amplifier configuration commonly used for amplification, buffering, filtering, and voltage comparison. An operational amplifier is a high-gain analog building block that compares an input signal with a feedback network and drives its output toward the difference between those signals. The dual-amplifier hierarchy connects the LM358BIDR to operational amplifiers, analog amplifiers, linear amplifiers, and integrated circuits. Two independent channels in one package reduce board area while providing a common supply arrangement for industrial controls, instrumentation, sensor interfaces, and general-purpose embedded systems. Key characteristics include two amplifier circuits, a 36 V maximum supply voltage, a 1.2 MHz gain-bandwidth product, and a 3 mV offset voltage. The 8-SOIC format supports automated surface-mount assembly and standard 1.27 mm pitch PCB layouts. Because the part is intended for broad analog applications, its useful performance depends on the selected feedback network, supply voltage, output load, input common-mode range, and required accuracy. The LM358BIDR belongs to the LM358B family of industry-standard dual operational amplifiers. Its internally compensated architecture simplifies typical closed-loop amplifier and voltage-follower configurations. Designers should still verify input and output operating limits for the intended supply and signal ranges in the manufacturer datasheet, particularly when approaching the device's maximum rated supply voltage. Typical applications include sensor signal conditioning, transducer amplification, analog filtering, comparator-style control loops, current-voltage conversion, audio preamplification, and general industrial signal conditioning. The dual-channel arrangement is particularly useful when a board needs two related analog channels without requiring a quad-amplifier package or two separate single-channel devices. For PCB implementation, place input, output, feedback, and decoupling connections to minimize parasitic coupling and preserve signal integrity. Keep sensitive input traces away from high-current switching paths, use a local supply bypass capacitor, and route the ground return carefully to reduce offset and noise pickup. Confirm output-current capability and stability with the selected load before committing to the design. This page organizes the exact LM358BIDR identity, package information, sourcing fields, replacement considerations, and application guidance into a practical engineering reference. It also distinguishes verified target-part characteristics from comparison fields that require an individual manufacturer datasheet review before a board redesign is approved.

RFQ Contact
LM358BIPWR - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM358BIPWR

LM358BIPWR - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM358BIPWR is a dual, general-purpose operational amplifier designed for a 3 V to 36 V supply range, with a unity-gain bandwidth of 1.2 MHz, an input offset voltage of 3 mV, and low quiescent current of 300 uA per channel. The device is packaged in an 8-pin TSSOP (PW) package and is specified for operation from -40 °C to +85 °C. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. It belongs to the amplifier hierarchy that includes differential amplifiers, instrumentation amplifiers, and the broader category of analog signal-chain ICs. The LM358B contains two independent, internally compensated amplifiers sharing common supply and ground pins, making it useful where two amplified signals must be handled in one compact package. The LM358B version provides several characteristics suited to industrial and general-purpose designs. Its 3 V to 36 V operating range allows operation from conventional 5 V and 12 V rails as well as higher industrial supply voltages. A 300 uA quiescent current per channel supports power-conscious instrumentation, while the 1.2 MHz unity-gain bandwidth provides useful response for audio, control, and low-frequency signal-conditioning applications. Its common-mode input voltage range includes ground, enabling direct sensing of signals near the lower supply rail. Internally, each channel combines high open-loop gain with frequency compensation, allowing the device to operate as a unity-gain stable buffer without an external compensation capacitor. The two amplifiers are independent, although they share the same supply pins. This arrangement permits simultaneous functions such as signal amplification and active filtering, or two channels of sensor conditioning, while keeping the component count and PCB area below that of separate single-channel amplifiers. Typical applications include low-level sensor signal conditioning, transducer amplification, active filters, audio preamplifier stages, motor and actuator control loops, and general industrial control systems. The 8-pin TSSOP package is particularly useful for compact analog boards where a dual amplifier is required but SOIC or larger packages would be unnecessary. When designing around the LM358BIPWR, maintain adequate input and output voltage headroom at the selected supply voltage, especially for output swings near either rail. Place input-referring components close to the amplifier pins, keep feedback traces short, and verify that the intended signal bandwidth remains well below the 1.2 MHz unity-gain limit. Decoupling capacitance should be selected according to the manufacturer's recommended application circuit and layout guidance. This page combines manufacturer specifications, distributor availability information, cross-reference results, application guidance, and practical design considerations. It is intended to help engineers evaluate the LM358BIPWR for industrial, instrumentation, audio, and embedded-control designs without relying solely on a catalog parameter table.

RFQ Contact
LM358BP - Dual Operational Amplifier | Texas Instruments
LM358BP

LM358BP - Dual Operational Amplifier | Texas Instruments

The Texas Instruments LM358BP is a dual operational amplifier in an 8-pin surface-mount package, combining two independent amplifiers for general-purpose analog signal conditioning. The LM358BP is associated with the LM358 family, a low-power dual op-amp solution designed for applications requiring wide supply-voltage range, high open-loop gain, and straightforward single-supply operation. The verified manufacturer information identifies the LM358 family as a dual operational amplifier offering low power consumption, high gain, and a wide voltage range, while the LM358B device is specified as a dual, 36-V, 1.2-MHz, 3-mV-offset operational amplifier with an operating-temperature range of -40°C to 85°C. An operational amplifier is an active semiconductor device that uses differential input voltage to control an output voltage. A dual operational amplifier contains two amplifier sections in one package, allowing designers to implement two signal-processing channels while reducing board area and component count. The LM358BP is therefore useful in sensor interfaces, transducer amplifiers, voltage comparators, current-monitoring circuits, audio preamplifier stages, and general feedback-control circuits. Its dual architecture can also simplify designs in which two independent amplifier functions are required at similar supply and performance levels. The LM358B family is described by Texas Instruments as a dual, 36-V operational amplifier with 1.2-MHz bandwidth and 3-mV maximum offset voltage. The LM358BP ordering code identifies the specific package and ordering variant of this family. The verified distributor listing describes the device as a standard or general-purpose amplifier with two circuits, and identifies the package as an 8-pin micro PBGA surface-mount package. Because the exact package dimensions, pin assignments, and full electrical limits are not included in the manufacturer result excerpts used for this page, individual electrical values should be confirmed against the manufacturer datasheet before final circuit release. The LM358 family is commonly associated with low-power operation, high gain, and a wide operating-voltage range. In practical designs, the amplifier can be used with single-supply systems where the input and output signals remain within the common-mode and output-swing limits. The LM358BP is appropriate where two channels are needed and where a simple, widely understood dual-op-amp architecture is preferable to a more specialized precision or high-speed amplifier. Typical applications include resistive sensor conditioning, buffered instrumentation inputs, low-frequency audio amplification, comparator functions, and general feedback amplifiers. The device can reduce board area by providing two amplifiers in one package, while the family-level supply range supports operation from conventional single-supply rails. Designers should still verify input common-mode range, output swing, output-current capability, noise, offset drift, and stability requirements against the complete LM358B datasheet. For PCB implementation, use the manufacturer land pattern for the LM358BP package rather than substituting a generic SOIC-8 footprint. Place input, output, and supply bypass capacitors close to the relevant pins, maintain a short return path for ground currents, and avoid routing sensitive input traces beside the output stage. This page combines manufacturer family information, distributor identification, drop-in alternatives, application guidance, and design considerations to support component selection and PCB planning.

RFQ Contact
LM358BPX - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM358BPX

LM358BPX - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM358BPX is a dual, general-purpose operational amplifier with two independent channels, a 36 V maximum supply rating, a 1.2 MHz gain-bandwidth product, and an 8-ball VFBGA package. The device combines a 3 mV input-offset-voltage rating with a 0.5 V/us slew rate, making it suitable for low-to-moderate-speed analog signal conditioning, feedback-control loops, and general-purpose amplification. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, signal-conditioning ICs, and analog front-end components. Its two independent channels permit simultaneous processing of related signals without requiring two separate single-channel packages. The principal LM358B-family characteristics include operation from a single supply or from split positive and negative supplies, a 1.2 MHz unity-gain bandwidth, a 0.5 V/us slew rate, and a 3 mV maximum input-offset voltage. According to the TI LM358B product page, the commercial-temperature family operates from -40°C to 85°C. These characteristics place the amplifier between precision low-noise amplifiers and high-speed operational amplifiers: it offers useful DC accuracy and common-mode flexibility without the bandwidth of a high-speed comparator or precision amplifier. Each channel includes one input stage, an output stage, and compensation circuitry. The two amplifiers are independent rather than internally linked, allowing the same package to implement independent gain stages, comparators, buffers, or transducers. The 0.5 V/us slew rate limits how quickly a large output transition can occur, while the 1.2 MHz gain-bandwidth product limits closed-loop bandwidth as feedback gain increases. A practical gain-bandwidth relationship of 1.2 MHz divided by noise gain gives a useful first estimate of usable bandwidth. Typical uses include temperature-sensor signal conditioning, audio preamplification, DC motor-current monitoring, industrial sensor interfaces, low-frequency active filters, and power-supply feedback. For sensor applications, the 3 mV offset specification is important because input-referred offset appears directly at the amplifier output after multiplication by the closed-loop noise gain. In AC-coupled audio paths, the slew rate and bandwidth determine whether large low-frequency signals can be reproduced without excessive distortion. PCB design should prioritize short input and feedback paths, a stable output connection, and careful bypassing of the positive supply. Because the LM358BPX uses a compact ball-grid package, the manufacturer land pattern and pin-description table should govern assembly and inspection. Decoupling capacitors should be placed close to the supply and ground balls, while analog input traces should be kept away from switching nodes and high-current return paths. This page combines the LM358B family electrical characteristics, LM358BPX package information, pin assignments, verified source links, and practical guidance for analog-board design. It also identifies the limits of direct substitution: many LM358 equivalents use DIP or SOIC packages rather than the LM358BPX 8-ball VFBGA footprint, so a functional match does not necessarily qualify as a PCB drop-in replacement.

RFQ Contact
LM358D - Dual 700kHz General Purpose Op Amp | Texas Instruments (Tape & Reel)
LM358D

LM358D - Dual 700kHz General Purpose Op Amp | Texas Instruments (Tape & Reel)

The LM358D is a dual operational amplifier from Texas Instruments in an 8-pin SOIC (D) surface-mount package. It operates from a single supply of 3V to 32V or dual supplies of ±1.5V to ±16V, with a gain bandwidth product of 700 kHz and a slew rate of 0.3 V/µs. This industry-standard, low-cost amplifier serves a vast range of general-purpose analog functions. An operational amplifier (op amp) is a high-gain differential-input, single-ended-output voltage amplifier and one of the most fundamental building blocks in analog electronics. General-purpose op amps like the LM358 prioritize versatility, low cost, and ease of use over precision or bandwidth. The LM358 is the dual version of the LM321 single amplifier and the two-amp counterpart of the quad LM324. Key features include a common-mode input voltage range that extends to ground, enabling direct sensing near ground in single-supply systems; low supply current of 0.7 mA typ, independent of supply voltage; internal frequency compensation for unity-gain stability; and short-circuit protected outputs. These characteristics suit battery-powered and cost-sensitive designs. Technically, the LM358 uses a bipolar process with a class-AB output stage that can drive loads as low as 2 kΩ with a large output swing. The commercial temperature grade is 0°C to +70°C. Input bias and offset currents are low, and the two internal amplifiers are well matched, sharing the same supply and bias circuitry. Typical applications include transducer amplifier front ends, DC gain blocks, active RC filters, voltage comparators and level shifters, power-supply feedback loops, and portable or industrial control electronics. The SOIC-8 package supports automated SMT assembly and reflow. Design considerations: decouple V+ to GND with a 0.1 µF ceramic capacitor close to pin 8, and respect output swing limits near the rails (output saturates roughly 1.5V below V+ at moderate loads). For higher bandwidth or lower noise, consider the pin-compatible TLV9152 or TL072. Pricing as of 2026-08-30 starts around $0.05 at volume from distributors such as LCSC.

RFQ Contact
LM358D-JF - Dual Op-Amp, 2 Circuit, SOIC-8 | Texas Instruments
LM358D-JF

LM358D-JF - Dual Op-Amp, 2 Circuit, SOIC-8 | Texas Instruments

The Texas Instruments LM358D-JF is an industry-standard dual operational amplifier integrating two independent, internally compensated op-amp circuits in a single 8-pin SOIC package. According to the TI LM358 family datasheet, the device operates from a single supply as low as 3 V (B and BA versions) with a wide supply range up to 36 V, draws approximately 300 uA per channel of quiescent current (B and BA versions), and delivers a unity-gain bandwidth of about 1.2 MHz on the enhanced B/BA versions, with the standard LM358 characterized at 700 kHz on a 30-V class supply. The common-mode input voltage range includes ground, enabling direct sensing of signals near 0 V without a negative rail. An operational amplifier is an analog voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of the linear signal chain: op-amp -> amplifier IC -> analog front end -> mixed-signal system. Dual op-amps such as the LM358D-JF combine two such stages behind one supply pin, halving board area and supply routing complexity compared with two single amplifiers. Key features include ground-sensing inputs for single-supply operation, a wide supply range supporting both 5 V logic-level and up to 36 V industrial rails (B/BA versions), low 300 uA-per-channel quiescent drain (B/BA versions) for battery-powered designs, and internally compensated unity-gain stability. The maximum input offset voltage of 2 mV at 25 C (BA version) keeps DC accuracy adequate for non-critical gain stages. The architecture uses a classic bipolar process with internal frequency compensation, giving well-behaved, phase-margin-safe behavior in inverting, non-inverting, and unity-gain buffer configurations. Output stages sink and source small currents and pull down close to ground on single supplies, which is why the LM358 remains the default comparator-adjacent amplifier for cost-driven designs. Typical applications include transducer signal conditioning near ground, low-speed active filters, current-sense front ends in power supplies and chargers, and level-shifting stages in industrial sensor nodes. The SOIC-8 surface-mount footprint suits compact commercial PCBs. Design consideration: keep closed-loop gains moderate and load capacitance low; the modest bandwidth means these parts are intended for slow, robust analog functions rather than wideband signal paths. This page adds value beyond the manufacturer datasheet by consolidating pin-compatible alternatives, pricing-channel availability, and practical design notes in one place.

RFQ Contact
LM358DE4 - 700kHz Dual Op Amp, 16V | Texas Instruments
LM358DE4

LM358DE4 - 700kHz Dual Op Amp, 16V | Texas Instruments

Texas Instruments LM358DE4 is a dual general-purpose operational amplifier IC with two independent amplifier channels, a 700 kHz gain-bandwidth product, and operation from a 16 V maximum supply, packaged in an 8-pin SOIC. The device is intended for general-purpose analog signal conditioning, buffering, current sensing, filtering, analog measurement, and precision-control applications. An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to amplify the difference between two input voltages. The LM358 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, and semiconductor. Its dual-channel architecture provides two amplifiers in one package, reducing board area when two related analog functions are required. Unlike precision rail-to-rail amplifiers, the LM358 uses bipolar transistor circuitry and is therefore especially familiar in supply-voltage-oriented industrial, instrumentation, and control designs. Key characteristics include two amplifier circuits, a 700 kHz gain-bandwidth product, and a 16 V maximum supply identified by the manufacturer-oriented product information. The 8-SOIC package uses eight terminals in a rectangular surface-mount gull-wing format. Its dual-channel organization is useful for signal conditioning, buffering, current sensing, analog measurement, filtering, and precision-control circuits where two amplifiers share the same supply and ground references. The 700 kHz gain-bandwidth product makes the LM358 suitable for general-purpose closed-loop amplifier stages operating at low-to-moderate signal frequencies. In a non-inverting configuration, closed-loop bandwidth depends on the selected feedback network rather than the open-loop gain-bandwidth product alone. The bipolar implementation also supports operation from a single positive supply, allowing input and output signals to be referenced toward ground in many industrial and embedded analog circuits. Typical applications include sensor-signal conditioning, transducer buffering, active filtering, low-side current sensing, analog control loops, and general measurement boards. Two channels can implement differential signal conditioning, active filters, comparator-style threshold conditioning with suitable feedback arrangements, or independent amplifier stages sharing the same supply. The SOIC package is also convenient for prototype boards and production assemblies that use conventional surface-mount footprints. Design attention should focus on input common-mode range, output swing, load capability, and stability with the selected feedback network. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be kept away from switching nodes. Because the device is not rail-to-rail at its inputs and outputs, verify signal levels against the operating supply before using it in low-voltage battery systems. This page organizes the LM358DE4 specifications, pin and package information, application guidance, and pin-compatible alternatives into one engineering-focused reference. It also provides practical selection criteria for comparing the standard LM358 family with alternate dual-amplifier implementations before committing a PCB footprint to production.

USD $1.31 In Stock
LM358DG - Dual 1 MHz Operational Amplifier | onsemi
LM358DG

LM358DG - Dual 1 MHz Operational Amplifier | onsemi

The onsemi LM358DG is a dual general-purpose operational amplifier with two amplifier channels, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a 3 V to 32 V operating supply range. The device is supplied in an 8-SOIC package and supports both single-supply and split-supply operation. Its common-mode input range extends to ground and VEE, making it suitable for signal conditioning, current monitoring, and general industrial-control circuits. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification and feedback to control gain accurately. The dual LM358 architecture provides two amplifiers in one package, reducing board area while offering independent input, output, and supply connections. The LM358 belongs to the operational-amplifier hierarchy, which also includes single and quad amplifier packages used in instrumentation, sensor interfaces, and power-management systems. Key characteristics include a 3 V to 32 V supply range, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and a common-mode rejection ratio listed at a minimum of 65 dB. Input offset voltage is listed as 7 mV. The common-mode input voltage range extends to ground or VEE, allowing the amplifier to process signals near the lower supply rail. Low power drain and single- or split-supply flexibility suit both portable and industrial equipment. The dual amplifier can be used in noninverting and inverting gain stages, voltage followers, comparators, differential amplifiers, current-to-voltage converters, and sensor-signal conditioning. Independent channels allow one package to implement two related analog functions while sharing the same supply pins. However, users should verify input/output swing limits, output-current capability, stability conditions, and absolute maximum ratings in the manufacturer datasheet for the exact operating point. For PCB design, place the bypass capacitor close to the supply pin and route each amplifier's feedback and input traces away from switching nodes and high-current paths. Because the common-mode range extends toward ground but not necessarily beyond the positive rail, input signals must remain inside the specified common-mode limits. Stable feedback-network layout and adequate output-load compatibility are essential for reliable closed-loop behavior. This product page combines verified manufacturer and distributor information, same-footprint replacement candidates, parameter comparisons, and practical implementation guidance. It is intended to help engineers identify whether the LM358DG's dual-channel, wide-supply, near-ground-input capability fits a design before consulting the full manufacturer datasheet.

RFQ Contact
LM358DG4 - Dual 700kHz Op Amp, 16V SOIC | Texas Instruments
LM358DG4

LM358DG4 - Dual 700kHz Op Amp, 16V SOIC | Texas Instruments

The Texas Instruments LM358DG4 is a dual general-purpose operational amplifier in an 8-pin SOIC package. It provides two amplifier circuits, a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operation from a maximum total supply voltage of 16 V. The device is packaged in a tube and is intended for general-purpose signal conditioning, buffering, and analog control applications. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. A dual operational amplifier combines two amplifier channels in one package, reducing board area when a design needs two independent gain stages or one amplifier can be reserved as a buffer. Within the broader hierarchy, the LM358 belongs to the operational amplifier, linear amplifier, and analog signal-conditioning IC categories. The LM358DG4's 700 kHz gain-bandwidth product supports signal paths that do not require high-frequency specialized amplifiers. Its 0.3 V/us slew rate defines how quickly the output can follow large voltage changes. The two amplifier circuits share the same 8-SOIC package and are identified as a general-purpose amplifier type in the product listing. The SOIC-8 format is a surface-mount package with gull-wing leads on the package sides. It is larger than modern compact packages but remains widely supported by standard PCB assembly equipment. Using one dual amplifier instead of two separate single-channel devices can reduce component count, simplify routing, and conserve board area where both channels perform similar signal-conditioning functions. Typical applications include low-frequency sensor conditioning, buffered analog inputs, active filtering, comparator-style threshold functions, and general instrumentation. The LM358DG4 is also suitable for educational and prototype circuits where a conventional dual operational amplifier is required without specialized low-noise, high-speed, or rail-to-rail performance. Designers should verify input common-mode range, output swing, input bias current, supply-current behavior, and stability requirements against the manufacturer datasheet for the intended operating conditions. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be configured so they do not float. The SOIC-8 footprint and pin arrangement should be checked against the selected board layout before substitution. This product data consolidates the verified device identity, package, channel count, bandwidth, slew-rate, supply-voltage, and cross-reference information. It also adds application guidance, side-by-side parameter coverage, and practical design notes to help engineers evaluate the LM358DG4 for analog signal-conditioning designs.

RFQ Contact
LM358DGKR - Dual 36V Operational Amplifier | Texas Instruments
LM358DGKR

LM358DGKR - Dual 36V Operational Amplifier | Texas Instruments

Texas Instruments LM358DGKR is a dual general-purpose operational amplifier with two amplifier channels, a 36 V maximum supply rating, a typical input offset voltage of 300 µV, and an 8-pin VSSOP package. It is designed for cost-sensitive analog signal conditioning across industrial, instrumentation, communications, and embedded-control systems. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose open-loop behavior is shaped by external feedback networks. The LM358 belongs to the broader operational-amplifier hierarchy, within analog ICs and signal-chain conditioning. Its two independent channels allow one package to implement functions such as amplification, buffering, voltage comparison, difference amplification, and basic active filtering. Key features include two amplifier circuits in one package, a supply capability reaching 36 V, input offset voltage of 300 µV typical, a common-mode input range that extends to ground, and high differential-input-voltage capability. These characteristics suit systems whose signal levels vary widely and whose analog section operates from a single positive supply. The device also provides a practical choice for cost-sensitive designs because two channels reduce component count and board area. The LM358 architecture is intended for general-purpose rather than precision applications. Its typical 300 µV offset is useful for moderate-accuracy signal conditioning but requires careful bias-current compensation when the source impedance is high. Ground-referenced inputs are supported, which helps simplify single-supply interfaces. Designers should still evaluate output swing, input common-mode limits, supply headroom, capacitive-load stability, and channel-to-channel behavior at the selected voltage and temperature. Typical uses include sensor-amplifier interfaces, transducer signal conditioning, low-side current measurement, audio preamplification, comparator stages, industrial control loops, and general buffering. In instrumentation designs, the two channels can process complementary or sequential signals. The 8-pin VSSOP outline supports compact layouts, although careful input routing and stable feedback connections remain important in noisy systems. A key design consideration is to place input, feedback, and decoupling components close to their associated pins. Bypass the supply with a short, low-inductance connection, avoid long high-impedance input traces, and verify stability when driving capacitive loads. The common-mode input range and output swing must both be checked at the minimum and maximum operating supply. This page combines manufacturer specifications, package guidance, commercially sourced alternatives, and practical design guidance for engineers evaluating the LM358DGKR as a dual, general-purpose, high-voltage operational amplifier.

RFQ Contact
LM358DGKRG4 - Dual 700kHz Op Amp, 8-VSSOP | Texas Instruments
LM358DGKRG4

LM358DGKRG4 - Dual 700kHz Op Amp, 8-VSSOP | Texas Instruments

Texas Instruments LM358DGKRG4 is a dual, general-purpose operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and an 8-VSSOP package. The device is intended for commercial-grade instrumentation and signal-conditioning systems operating from a single supply or a split supply. Its package uses eight gull-wing terminals in a compact surface-mount TSSOP-compatible footprint. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the broader operational-amplifier, linear-amplifier, and semiconductor hierarchy. Two amplifiers are integrated into one package, allowing one IC to support signal buffering, amplification, filtering, comparisons, and feedback-control functions while reducing board area and component count. The LM358 family provides differential inputs, high open-loop gain, frequency compensation, and the ability to operate from a single supply or split supply. Each amplifier in the LM358DGKRG4 is configured for general-purpose use rather than rail-to-rail input and output operation. The verified product description identifies the part as a 2-circuit amplifier in an 8-VSSOP package, while the manufacturer nomenclature identifies it as a 700 kHz device. The eight-terminal surface-mount package makes the device suitable for compact analog boards, but layout still requires care around feedback components and supply connections. Pin 8 is the positive supply, pin 4 is the negative supply or ground reference, and the remaining pins divide into two independent amplifier sections. Because the LM358 is a frequency-compensated operational-amplifier family, external stability networks are generally unnecessary for ordinary closed-loop uses. Typical applications include low-level sensor conditioning, current-loop receivers, audio preamplifier stages, active filters, comparators, feedback-control loops, and general-purpose analog signal processing. The two independent channels can be used simultaneously when channel requirements are similar, or one channel can remain unused when its input and output are properly configured. When designing around the LM358DGKRG4, verify the input common-mode range and output swing against the actual supply voltage. Place bypass capacitance close to the supply pins, keep feedback-loop routing compact, and avoid long parallel traces between the input and output networks. The commercial temperature grade should be checked against the intended ambient operating range. This product record consolidates the verified manufacturer and distributor identification, package information, drop-in candidate analysis, pin assignment, comparison parameters, and practical layout guidance. It is structured to support engineering selection for the LM358DGKRG4 and to distinguish confirmed drop-in options from candidates requiring additional qualification.

RFQ Contact
LM358DMR2 - Dual 3-32V Low-Power Op Amp | onsemi
LM358DMR2

LM358DMR2 - Dual 3-32V Low-Power Op Amp | onsemi

onsemi LM358DMR2 is a dual general-purpose operational amplifier with two independent amplifier channels, a 3 V to 32 V operating supply range, and an 8-MSOP surface-mount package. It operates from a single supply or split supply, supports input common-mode voltages extending to ground and VEE, and is suited to low-voltage signal conditioning, sensing, and feedback-control circuits. An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the dual-operational-amplifier family within the broader linear-IC and signal-chain hierarchy. Its common-mode input range, low power consumption, and ability to operate close to the negative supply rail make it useful for battery-powered equipment, industrial controls, transducers, and general-purpose embedded systems. Key characteristics include typical input offset voltage of 3 mV, typical input offset current of 2 nA, typical input bias current of 20 nA, and typical supply-current drain of 0.7 mA per amplifier. The differential input range is equal to the maximum rated supply voltage. These specifications support precision-oriented applications where offset, bias current, power consumption, and usable input range must be balanced rather than optimized for only one parameter. The LM358DMR2 contains two independent, internally frequency-compensated amplifiers. Internal compensation simplifies closed-loop implementation because no external compensation network is required for ordinary voltage-feedback use. The dual configuration reduces component count in designs that need two gain stages, differential sensing, or multiple analog channels, while the common 8-MSOP footprint supports compact surface-mount assemblies. Typical uses include low-side current sensing, sensor amplification, buffer stages, threshold detection, and feedback loops in industrial and consumer equipment. Its ground-referenced common-mode capability is particularly useful for circuits powered from a single positive rail, where the signal may approach 0 V. For split-supply systems, operation can extend down toward VEE, subject to the applicable input and output limits. PCB design should keep feedback routing short, place input and output decoupling close to the device, and provide stable reference and return paths. Avoid placing long high-impedance traces beside switching nodes. The output must remain within its rated swing range, and applications must verify that the selected gain, load, supply voltage, and temperature remain within the device limits. This product page combines the exact LM358DMR2 ordering information with electrical characteristics, a complete 8-pin assignment, application guidance, PCB considerations, and a strict assessment of drop-in replacement evidence. The replacement section avoids presenting pin-compatible parts with different package outlines as direct substitutions.

RFQ Contact
LM358DMR2G - Dual 1 MHz Op Amp, 3-32 V, 8-MSOP | onsemi
LM358DMR2G

LM358DMR2G - Dual 1 MHz Op Amp, 3-32 V, 8-MSOP | onsemi

onsemi LM358DMR2G is a dual general-purpose operational amplifier with two independent, internally compensated amplifiers, a 1 MHz gain-bandwidth product, a 0.6 V/µs slew rate, and operation from 3 V to 32 V in an 8-MSOP package. The LM358 family is designed for single-supply or split-supply operation and can tolerate input common-mode voltages extending to ground or VEE. An operational amplifier is a general-purpose analog building block that amplifies the voltage difference between its non-inverting and inverting inputs. The LM358 belongs to the dual-operational-amplifier hierarchy, combining two amplifier channels in one package for signal conditioning, buffering, filtering, feedback control, and low-frequency analog control applications. Each channel offers 1 MHz gain-bandwidth, 0.6 V/µs slew rate, and up to 40 mA output current. Its common-mode input range extends to ground or VEE, which makes it useful in single 3 V to 32 V supply systems where the signal can approach the lower supply rail. The device also supports dual-supply operation for circuits requiring bipolar signal ranges around ground. The internally frequency-compensated architecture reduces external compensation requirements and supports general-purpose closed-loop amplifier configurations. Because the LM358 is intended for moderate-bandwidth analog tasks rather than high-speed precision signal chains, bandwidth, slew rate, output-current capability, input-offset behavior, and noise should be checked against the actual signal amplitude and load requirements. Typical uses include sensor-signal conditioning, low-frequency active filters, transducers, audio and communication interfaces, motor-control feedback paths, and industrial control loops. Its 8-MSOP surface-mount package supports compact analog designs, while the two channels can implement independent amplifier functions or complementary push-pull output stages when circuit conditions permit. Layout should keep feedback components and sensitive input nodes compact, provide a stable local power bypass path, and avoid placing high-current return currents near the input reference. The 3 V minimum supply and 32 V maximum supply must remain within ratings at all times, including transients. Output loading should not exceed the device's stated 40 mA capability. This page combines the exact LM358DMR2G electrical and package characteristics with application guidance, a verified same-package comparison candidate, practical layout advice, and structured specifications that help engineers determine whether this general-purpose dual amplifier fits a specific analog design.

RFQ Contact
LM358DR - Dual 700kHz General Purpose Op Amp | Texas Instruments
LM358DR

LM358DR - Dual 700kHz General Purpose Op Amp | Texas Instruments

The LM358DR is a dual operational amplifier from Texas Instruments in an 8-pin SOIC (D) surface-mount package. It operates from a single supply of 3V to 32V or dual supplies of ±1.5V to ±16V, with a gain bandwidth product of 700 kHz and a slew rate of 0.3 V/µs. This industry-standard, low-cost amplifier serves a vast range of general-purpose analog functions. An operational amplifier (op amp) is a high-gain differential-input, single-ended-output voltage amplifier and one of the most fundamental building blocks in analog electronics. General-purpose op amps like the LM358 prioritize versatility, low cost, and ease of use over precision or bandwidth. The LM358 is the dual version of the LM321 single amplifier and the two-amp counterpart of the quad LM324. Key features include a common-mode input voltage range that extends to ground, enabling direct sensing near ground in single-supply systems; low supply current of 0.7 mA typ, independent of supply voltage; internal frequency compensation for unity-gain stability; and short-circuit protected outputs. These characteristics suit battery-powered and cost-sensitive designs. Technically, the LM358 uses a bipolar process with a class-AB output stage that can drive loads as low as 2 kΩ with a large output swing. The commercial temperature grade is 0°C to +70°C. Input bias and offset currents are low, and the two internal amplifiers are well matched, sharing the same supply and bias circuitry. Typical applications include transducer amplifier front ends, DC gain blocks, active RC filters, voltage comparators and level shifters, power-supply feedback loops, and portable or industrial control electronics. The SOIC-8 package supports automated SMT assembly and reflow. Design considerations: decouple V+ to GND with a 0.1 µF ceramic capacitor close to pin 8, and respect output swing limits near the rails (output saturates roughly 1.5V below V+ at moderate loads). For higher bandwidth or lower noise, consider the pin-compatible TLV9152 or TL072. Pricing as of 2026-08-30 starts around $0.05 at volume from distributors such as LCSC.

RFQ Contact
LM358DR2 - Dual 3-32V Op Amp | onsemi | Industrial
LM358DR2

LM358DR2 - Dual 3-32V Op Amp | onsemi | Industrial

The onsemi LM358DR2 is a single-supply dual operational amplifier designed for 3 V to 32 V operation and packaged in an 8-pin SOIC. It contains two amplifiers and supports single-supply or split-supply operation. Its common-mode input voltage range extends to ground and VEE, making it suitable for low-side sensing, signal conditioning, feedback control, and general-purpose analog circuits powered from industrial or automotive-style rails. The device is identified by the onsemi LM358DR2 ordering code and is associated with the LM358 family of low-power dual operational amplifiers. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare two input voltages. The LM358 family combines two amplifiers in one package, reducing board area compared with two separate single amplifier packages. A low-dropout single-supply architecture allows the amplifier to operate from a supply only slightly above the required output range, while the common-mode input range extending toward ground supports sensors whose signals begin near 0 V. The principal application advantages are the dual-channel configuration, 3 V to 32 V supply range, low power drain, and flexible single- or split-supply use. Two independent amplifier channels can implement non-inverting or inverting gain stages, differential sensing, comparators, active filters, transimpedance stages, and feedback loops. The 8-pin SOIC package supports compact PCB layouts and automated assembly, but the exposed package lead geometry and electrical limits must still be checked against the circuit requirements. The LM358 architecture is intended for general-purpose analog signal conditioning rather than high-speed, precision, or rail-to-rail applications. Designers should account for input bias current, input offset voltage, output-current capability, common-mode limits, and output-swing behavior in each operating condition. Because no complete timing, noise, accuracy, or output-drive table appears in the product results, those values should be taken directly from the manufacturer data sheet before sizing external resistors or capacitors. Typical uses include conditioning a 0 V to sensor-range signal, buffering a potentiometer, amplifying strain-gauge or thermocouple outputs, driving analog control loops, and forming active filters. In industrial systems, the 32 V maximum listed supply voltage provides compatibility with higher-voltage rails, but the design still requires correct input and output common-mode ranges for each channel. The main layout consideration is decoupling. Place the supply bypass capacitor close to the positive supply and ground pins, keep feedback-loop routing short, and return analog-ground currents directly to the device ground rather than through high-current switching paths. Check bias-current-induced offset and output-swing limits before using the amplifier with high-impedance sources, and verify that the selected SOIC footprint matches the exact ordering code. This product record combines the verified LM358DR2 identity, supply-range description, package information, sourcing links, drop-in comparison, and practical design guidance. It is intended to help engineers identify the correct dual amplifier and assess PCB, layout, and application compatibility before releasing a schematic or BOM.

RFQ Contact
LM358DR2G - Dual 3-32V Op Amp, 1MHz, 8-SOIC | onsemi
LM358DR2G

LM358DR2G - Dual 3-32V Op Amp, 1MHz, 8-SOIC | onsemi

The onsemi LM358DR2G is a dual, general-purpose operational amplifier in an 8-pin SOIC package, specified for operation from 3 V to 32 V with a gain-bandwidth product of 1 MHz. Each of its two independent amplifier channels features internally compensated operation, high open-loop gain, and a common-mode input range that extends toward ground or the negative supply rail. The device supports both single-supply and split-supply configurations, making it suitable for industrial control, sensor conditioning, audio, and power-management circuits. A dual operational amplifier is a semiconductor containing two independent high-gain amplifier sections with internal frequency compensation. Within the broader IC hierarchy, it belongs to the operational amplifier family, which sits inside analog and amplifier ICs. The LM358 series is functionally similar to one half of a quad LM324, with the common-mode input range extending toward the VEE rail to simplify single-supply interfacing to sensors whose outputs remain close to 0 V. Principal electrical characteristics include a 3 V to 32 V operating supply range, a 1 MHz gain-bandwidth product, two amplifier circuits per package, and operation from a common ground or negative supply. The low power drain of the circuit designs from which the LM358 series was derived supports low-power industrial and instrumentation systems. The wide supply range allows the same amplifier topology to operate from regulated 5 V rails or directly from higher nominal industrial supply voltages, subject to the device ratings and local regulations. The LM358DR2G uses an internally compensated architecture with two independent channels. Internal compensation eliminates the need for an external dominant-pole capacitor in the basic non-inverting and inverting configurations, simplifying analog design and reducing component count. The common-mode input voltage range extending to ground makes the amplifier useful in battery monitoring, current-sense amplifiers, transducers, and interfaces whose signals do not swing far above the negative rail. Typical applications include 5 V and 24 V sensor-signal conditioning, low-side current sensing, audio preamplification, buffer stages, comparators with open-collector outputs, and general industrial control. Because both amplifiers share the same package and supply pins, the device can implement two independent stages or be configured as one differential amplifier using the second channel for feedback. The 8-SOIC package also supports automated assembly and is widely supported by standard analog design tools. When designing around the LM358DR2G, verify output-current capability for the selected load, especially when driving capacitive inputs, and check common-mode limits at the actual supply voltage. Place bypass capacitors close to the supply pins and route feedback and input traces away from switching nodes. This page combines manufacturer electrical characteristics, source traceability, drop-in alternatives, package details, and application-level engineering guidance for faster component selection.

RFQ Contact
LM358DR2GH - Dual 8-SOIC Operational Amplifier | onsemi
LM358DR2GH

LM358DR2GH - Dual 8-SOIC Operational Amplifier | onsemi

The onsemi LM358DR2GH is a dual, general-purpose operational amplifier packaged in an 8-pin SOIC. It combines two amplifier channels in one package and is intended for standard low-frequency signal-conditioning applications. The verified part information identifies a 2-circuit amplifier configuration, an 8-SOIC package, and a low power-consumption figure of 45 nA per channel. These characteristics place the device in the operational-amplifier family within the broader linear and analog semiconductor hierarchy. An operational amplifier is a voltage-controlled, high-gain differential amplifier used to amplify, buffer, compare, filter, or control analog signals. Its positive and negative inputs form the signal input, while the output provides the amplified result. The dual-channel LM358 architecture allows two independent amplifier functions to share one package, reducing board area and simplifying designs that need more than one analog signal path. Unlike precision, rail-to-rail, or low-noise modern amplifier families, the LM358 is primarily selected for its general-purpose versatility and broad supply compatibility. The key verified features are the dual 2-circuit configuration, 8-SOIC surface-mount package, and 45 nA per-channel power-consumption figure. The SOIC package is suitable for conventional reflow assembly and automated manufacturing, while its exposed pin layout supports straightforward routing of power and feedback connections. Two amplifiers in one package can be used for instrumentation amplification, active filtering, comparator functions, sensor conditioning, or buffering where a single amplifier would otherwise require multiple packages. The LM358DR2GH belongs to the LM358 family associated with single-supply operation from an industrial-style positive rail toward ground. Its two channels support common single-supply analog circuits, including non-inverting and inverting stages referenced to ground. Because a general-purpose dual amplifier is often selected for availability and direct replacement rather than specialized signal-chain performance, designers should still verify supply limits, input common-mode range, output swing, input offset, noise, and stability requirements in the manufacturer datasheet for the exact ordering code. Typical uses include low-level sensor amplification, audio preamplification, active filters, current monitoring, comparators with open-collector outputs, and general instrumentation. In a two-channel design, one section might amplify a sensor output while the other provides an active filter or buffer. The 8-SOIC format also simplifies conversion from traditional through-hole prototyping methods when a suitable adapter or equivalent SOIC footprint is used. For a new PCB, follow the exact pin assignments and decoupling guidance in the onsemi LM358 family documentation. Place the supply bypass capacitor close to the positive supply and ground pins, keep feedback traces short, and avoid routing sensitive input traces beside switching nodes. Check the footprint dimensions and pin-one orientation before assembly because an SOIC-8 footprint does not eliminate lead-pitch or orientation errors. This page combines package identification, sourcing information, application guidance, and drop-in replacement analysis for engineers evaluating LM358DR2GH. It highlights where the dual 8-SOIC device is useful while directing critical electrical validation to the manufacturer datasheet.

RFQ Contact
LM358DRE4 - Dual 8-SOIC General-Purpose Op Amp | Texas Instruments
LM358DRE4

LM358DRE4 - Dual 8-SOIC General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM358DRE4 is a dual general-purpose operational amplifier containing two independent, high-gain, frequency-compensated amplifiers in an 8-pin SOIC package. Each amplifier can operate from a single supply or split supply over a wide voltage range, making the device useful for industrial control, sensor conditioning, audio, and low-voltage analog systems. The LM358DRE4 is supplied in tape-and-reel packaging for automated surface-mount assembly. An operational amplifier is an analog semiconductor that amplifies the voltage difference between its differential inputs. The LM358 belongs to the general-purpose operational-amplifier class, within the broader hierarchy of analog amplifiers, amplifiers, and semiconductor signal-conditioning devices. Its internally compensated architecture simplifies design because an external compensation network is not required for ordinary closed-loop applications. The principal feature of the LM358DRE4 is its combination of two amplifiers in one 8-pin SOIC. This allows a dual circuit, such as a two-stage filter or an instrumentation amplifier front end, to occupy one PCB footprint. The two amplifiers are independent, allowing them to process different signals or implement separate gain stages. The device is supplied in a compact surface-mount package and is arranged for tape-and-reel manufacturing. According to the Texas Instruments product description, the LM358 devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed for single-supply or split-supply operation. Frequency compensation stabilizes closed-loop behavior in typical amplifier configurations, while the high gain supports useful amplification from small sensor and control signals. Its dual architecture can also reduce component count and simplify routing when two related analog channels must be processed. Typical applications include low-level sensor amplification, transducer signal conditioning, current-loop interfaces, audio preamplification, comparators, and general-purpose analog control. The same package and pin arrangement can simplify multi-channel designs when a board needs two amplifier functions but does not require high precision, rail-to-rail input/output operation, or unusually low offset voltage. Designers should verify the operating supply range, input common-mode range, output swing, offset voltage, bias current, slew rate, and channel behavior against the current Texas Instruments datasheet before fixing the power architecture. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be tied to a defined potential near the active signal range to avoid unintended behavior. This product page consolidates package, application, replacement, and design information for engineers evaluating the LM358DRE4. It also identifies same-footprint alternatives, highlights differences that affect replacement decisions, and provides practical guidance for decoupling, signal routing, and analog layout.

RFQ Contact