Products (44,000+)

MAX232CSE+T - +5V RS-232 Transceiver, 16-SOIC | Analog Devices
MAX232CSE+T

MAX232CSE+T - +5V RS-232 Transceiver, 16-SOIC | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX232CSE+T is a +5V-powered, multichannel RS-232 driver/receiver IC in a 16-pin narrow-body SOIC (SOIC-N-16) package. It integrates two RS-232 line drivers and two RS-232 line receivers and generates the required ±7.5V to ±12V RS-232 output levels from a single +5V supply via on-board charge-pump capacitors. The part is supplied in tape-and-reel (T+R) packaging and supports data rates up to 120 kb/s per the MAX232C variant specifications. A RS-232 transceiver (line driver/receiver) is an interface IC that translates logic-level signals (typically 0/5V or 0/3.3V CMOS/TTL) to the higher-voltage bipolar signaling levels defined by the EIA/TIA-232E and V.28/V.24 standards. These standards require driver outputs above ±5V into 3 kΩ loads and receivers that translate bipolar inputs to standard logic levels. The MAX232 sits in the interface IC family within the broader integrated circuits hierarchy: interface IC > transceiver > line driver/receiver > signal conditioning IC > semiconductor. Key features include single +5V operation eliminating the need for ±12V rails, integrated charge-pump voltage doubler/inverter requiring only four external 1 µF capacitors, true RS-232 compliant outputs (typically ±7.5V minimum), and on-board TTL/CMOS-compatible receiver inputs with 5 kΩ resistive pull-down to ground. The wide commercial operating temperature range (0 °C to +70 °C for the C-grade) suits point-of-sale terminals, industrial control consoles, and embedded serial ports. Architecturally, the MAX232 uses a switched-capacitor charge pump (typically a dual-pump Dickson topology) with internal MOSFET switches clocked above the audio band. This generates the negative rail from the +5V supply without inductors, keeping the solution purely capacitive. Receivers employ hysteresis on their inputs to reject noise on long cables. Typical applications include RS-232 serial ports on microcontrollers (Arduino, PIC, STM32), point-of-sale (POS) terminals, industrial control equipment, networking routers and switches with console ports, and legacy PC peripherals. The 16-SOIC narrow-body package and tape-and-reel shipping suit high-volume automated assembly. When designing, place the four charge-pump capacitors as close to the C1+, C1-, C2+, C2- pins as possible using short traces, and use the V+ and V- pins as additional bypass. For higher data rates above 120 kb/s or extended temperature ranges, consider the MAX232E (200 kb/s, -40 °C to +85 °C) or MAX3232 (3V to 5.5V operation) families. This page synthesizes distributor pricing, drop-in cross-brand alternatives such as the Sipex/MaxLinear SP232ACN-L/TR, and practical charge-pump layout guidance not typically consolidated in the manufacturer datasheet.

RFQ Contact
MAX232CWE+ - 5V Dual RS-232 Transceiver | Analog Devices
MAX232CWE+

MAX232CWE+ - 5V Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE+ is a +5 V-powered, dual RS-232 driver and receiver interface IC with two transmit channels and two receive channels, supplied in a 16-pin wide SOIC package. The verified distributor listing identifies it as a 2/2 full RS-232 transceiver, while the datasheet describes the MAX220-MAX249 family as line-driver and receiver devices intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12 V is unavailable. Its single-supply operation is valuable in battery-powered and modern digital systems that cannot provide conventional bipolar RS-232 rails. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the differential, bipolar signaling used by RS-232 links. The transmitter portion accepts TTL/CMOS-compatible inputs and produces RS-232 output levels, while the receiver portion accepts RS-232 inputs and returns logic-level signals to a host, controller, or peripheral. In the system hierarchy, the MAX232 belongs to interface ICs, serial-interface transceivers, and communication adapters rather than to the power-conversion or digital-processing categories. Key verified features include operation from a 4.5 V to 5.5 V supply, two drivers, two receivers, RS-232 interface compatibility, and a 16-pin wide SOIC package. The MAX232 family is specifically suited to EIA/TIA-232E and V.28/V.24 links and includes on-chip charge-pump support for generating the required RS-232 voltage levels from a single supply. Exact driver slew rate, receiver propagation delay, input and output capacitance, and shutdown-current details were not supplied in the retrieved data and should be confirmed from the manufacturer datasheet before precision timing or signal-integrity design. Typical applications include serial debug consoles, industrial-control equipment, instrumentation, point-of-sale systems, and legacy peripheral interfaces. The device is appropriate where a controller UART needs a compliant RS-232 electrical interface but the board cannot provide ±12 V. Designers should still verify cable length, data rate, grounding, protection requirements, and the logic levels of the connected host. This page combines the verified product identity, package information, interface purpose, distributor records, and cross-reference findings into an engineering-oriented selection summary. A key design consideration is to place the MAX232 close to the board connector and provide the required charge-pump capacitors exactly as specified by the manufacturer datasheet. Keep the RS-232 traces away from sensitive analog and high-speed digital paths, and provide suitable transient protection for exposed external connectors. The verified excerpts do not provide operating temperature, RoHS, REACH, lifecycle, or exact absolute-maximum ratings, so those values remain unconfirmed. This page consolidates verified distributor and cross-reference information, same-package RS-232 design guidance, and explicit engineering trade-offs that are not visible in a basic catalog listing. It is intended to support initial component selection while directing engineers to the official MAX232 datasheet and distributor records for final qualification.

RFQ Contact
MAX232CWE+T - Dual RS-232 Transceiver | Analog Devices
MAX232CWE+T

MAX232CWE+T - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE+T is a +5 V-powered, dual RS-232 line-driver and receiver IC providing one full-duplex RS-232 port in a 16-pin wide SOIC package. It supports data rates up to 120 kbps and targets EIA/TIA-232E, V.28, and V.24 communications interfaces. Its integrated charge-pump circuitry generates the positive and negative voltages required by RS-232 without a separate external power supply. An RS-232 transceiver is an interface IC that converts logic-level signals into differential bipolar RS-232 levels and converts received bipolar signals back into CMOS-compatible logic. The MAX232CWE+T belongs to the line-driver and receiver hierarchy, providing the physical-layer functions required to connect a UART, microcontroller, or embedded controller to a serial port. It is particularly useful where the system cannot provide the positive and negative rails normally associated with RS-232 equipment. Key features include two driver channels, two receiver channels, a single +5 V supply, and operation at 120 kbps. The charge-pump design permits RS-232 communication with only +5 V power, eliminating a dual-supply requirement and reducing board-level complexity. The wide SOIC package is a standard surface-mount option with adequate lead pitch for automated assembly and hand-soldering. The device uses five external charge-pump capacitors to develop the bipolar voltage levels required for reliable transmission. Designers should place these capacitors close to the associated device pins and follow the connection arrangement in the manufacturer datasheet. Short, direct signal paths on the printed circuit board help limit ringing, reduce radiated emissions, and preserve the receiver's input threshold margin. Typical uses include industrial serial consoles, instrumentation links, service equipment, barcode readers, point-of-sale terminals, and legacy peripheral connections. The MAX232CWE+T is appropriate where a +5 V system must communicate over an RS-232 cable with a host computer or controller while avoiding the older +12 V and -12 V supply architecture. Choose this part when the required data rate is 120 kbps or lower and a 16-pin wide SOIC footprint is already on the PCB. Verify signal levels, cable length, grounding, and receiver thresholds at the system level, because RS-232 is a single-ended interface that depends on a common reference between connected equipment. This page combines the manufacturer interface description with practical component comparison, pin-level implementation guidance, and design notes covering charge-pump capacitors, grounding, transmission limits, and second-source evaluation.

RFQ Contact
MAX232CWE-TG074 - 120kbps RS-232 Transceiver | Analog Devices
MAX232CWE-TG074

MAX232CWE-TG074 - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE-TG074 is a dual-driver, dual-receiver RS-232 line transceiver rated for data rates up to 120kbps and housed in a 16-pin SOIC package. It provides the electrical conversion between RS-232 logic-level signals and bipolar serial data, including the voltage translation required on both driver and receiver sides. The device is intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12V supplies are unavailable. A MAX232 is a bipolar RS-232 interface IC that converts TTL/CMOS-compatible logic signals into RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, it belongs to the line-driver and receiver category, interface IC family, and broader semiconductor product group. Two driver channels and two receiver channels allow one device to support a full-duplex serial link. The MAX232CWE-TG074 supports operation at up to 120kbps, making it suitable for common serial-console, industrial-control, point-of-sale, and embedded equipment links. Its integrated level translation reduces the need for external RS-232 driver and receiver components. The 16-SOIC package supports conventional surface-mount assembly and is suitable for compact industrial and commercial equipment designs. The MAX220 through MAX249 family is designed around EIA/TIA-232E and V.28/V.24 interface requirements, particularly where positive and negative supply voltages of approximately ±12V are not available. The CWE-TG074 ordering form identifies this part as a 16-SOIC RS-232 driver/receiver interface with two drivers and two receivers. Its interface architecture supports simultaneous transmit and receive paths when the host and peripheral provide complementary data and control signals. Typical applications include configuration-port and console interfaces in embedded systems, communication links between microcontrollers and industrial peripherals, RS-232 test equipment, and legacy peripheral connections requiring bidirectional data transfer. Designers should pay particular attention to cable length, signal integrity, grounding, and the distinction between logic-level and RS-232 voltage domains. For a new layout, place the MAX232CWE-TG074 close to the connector and preserve short, direct routes for the driver outputs and receiver inputs. Check the device's receive thresholds and the logic-level supply requirements of the connected controller. Add the charge-pump capacitors recommended by the manufacturer at the designated pins and avoid long stubs that could increase ringing or susceptibility to ESD events. This product page combines the available manufacturer-family information, package identification, interface characteristics, application guidance, and drop-in replacement options in a format designed for engineering selection. For complete channel assignments, absolute maximum ratings, electrical characteristics, and layout guidance, use the official MAX232CWE datasheet and the exact pin-description table before releasing a PCB or production design.

RFQ Contact
MAX232D - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI
MAX232D

MAX232D - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI

The Texas Instruments MAX232D is a 5V-powered, dual-driver / dual-receiver RS-232 transceiver that integrates an on-board capacitive charge-pump to generate the +/-9V TIA/EIA-232-F signaling voltages from a single 5V supply, delivered in a 16-pin SOIC (D) package. It supports data rates up to 120 kbps, accepts +/-30V input levels on the receiver inputs, and supplies 8 mA typical quiescent current from a 4.5V to 5.5V supply rail. The device is functionally designed to be interchangeable with the industry-standard Maxim MAX232 die. A dual EIA-232 (RS-232) line driver/receiver is an interface IC that bridges TTL/CMOS logic levels (0-5V) and the much higher bipolar voltage swings (+/-5V to +/-15V) required by legacy serial-port standards. By generating these higher rails internally from a single low-voltage supply, dual RS-232 transceivers eliminate the need for a separate negative or high-voltage power rail, simplifying board design and reducing BOM cost. In the broader product hierarchy, the MAX232D belongs to the EIA-232 transceiver family (RS-232 transceiver), then to the Interface ICs category, then to Integrated Circuits, ultimately serving as an enabler of UART-to-DB9 connectivity in microcontroller- and FPGA-based systems. Key features of the MAX232D include TIA/EIA-232-F and ITU V.28 compliance, +/-30V receiver input tolerance that survives mis-wired cables and transients, an integrated 5V-to-+/-10V charge pump with four external 1 uF capacitors (charge-pump flying capacitors), two drivers and two receivers in a single 16-pin SOIC package, and ESD protection on the RS-232 bus pins (per the family spec). The 120 kbps data rate is more than adequate for serial console, modem, and industrial telemetry traffic, while the wide 4.5V to 5.5V supply range accommodates standard 5V regulated rails and battery-powered designs with headroom. Architecturally, the charge pump uses a voltage-doubler plus an inverting charge pump clocked from an internal oscillator (typically 125 kHz to 250 kHz range), which provides the +10V and -10V rails that drive the RS-232 output stages. The receivers use Schmitt-trigger inputs with hysteresis for noise immunity on long cables. Compared to using a discrete transistor-based level shifter or a +-12V linear supply, the MAX232D solution occupies roughly 30 mm x 6 mm of board area and removes one power supply from the design. Typical applications include microcontroller UART-to-RS-232 conversion on serial ports of industrial PLCs, point-of-sale (POS) terminals, embedded debug consoles for firmware development, and legacy PC RS-232 COM ports. The MAX232D is also commonly deployed in factory automation where 5V microcontrollers need to drive RS-232-controlled motor drives or sensors. Other uses include test and measurement equipment (scopes and analyzers with serial ports), legacy networking gear with DB-9 management ports, and education/development boards (Arduino shield, FPGA dev kit UART bridges). When designing with the MAX232D, observe charge-pump capacitor polarity: TI recommends 1 uF (or larger) low-ESR ceramic capacitors on each of the four charge-pump pins (C1+, C1-, C2+, C2-, V+, V-). Place the capacitors as close to the IC as possible to minimize parasitic resistance and ringing. Avoid long cable stubs on T1OUT/T2OUT pins, and add TVS diodes for additional ESD protection if the application involves frequent cable mating/unmating. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MAX232DE4 - Dual RS-232 Transceiver, 5V, 16-SOIC | Texas Instruments
MAX232DE4

MAX232DE4 - Dual RS-232 Transceiver, 5V, 16-SOIC | Texas Instruments

The Texas Instruments MAX232DE4 is a dual RS-232 driver and receiver transceiver with two drivers, two receivers, a single 4.5 V to 5.5 V supply, and a 16-pin SOIC package. It supports data rates up to 120 kbit/s and includes on-chip charge-pump capacitors for generating the bipolar RS-232 voltage levels. The device is designed for bidirectional serial data links between TTL/CMOS logic and EIA/TIA-232 equipment. An RS-232 transceiver is an interface IC that translates low-voltage digital logic levels into RS-232 levels and converts incoming RS-232 signals back into TTL/CMOS levels. The MAX232 belongs to the interface IC hierarchy, where a transceiver integrates driver, receiver, and voltage-generation functions. It is commonly used in industrial control, data acquisition, embedded instrumentation, and legacy computer equipment. The verified product information identifies the MAX232DE4 as a 2/2 full RS-232 transceiver in a 16-SOIC package. It operates from a single 4.5 V to 5.5 V supply and supports an operating temperature range of 0 C to 70 C. Additional verified features include operation to 120 kbit/s, low supply current, and ESD protection exceeding 2000 V under the cited JESD test condition. The charge-pump circuit allows the device to generate positive and negative RS-232 levels from one low-voltage supply, avoiding a separate negative power rail. The dual-driver and dual-receiver organization supports two serial channels or a full-duplex link on one device. The receiver converts remote RS-232 signals into logic levels suitable for digital controllers, while the driver boosts local logic signals to RS-232 voltage levels. Typical uses include RS-232 links in test equipment, serial adapters, industrial controllers, point-of-sale systems, and embedded measurement products. The 16-SOIC package supports conventional surface-mount PCB assembly. The verified commercial result lists the part with DigiKey, Mouser, Octopart, and other distributors, but the supplied data does not provide a current unit price or confirmed lead time. For robust implementation, follow the manufacturer datasheet for capacitor selection, pin orientation, and signal-routing requirements. The MAX232DE4 is not a power semiconductor, so SOA data is not applicable. The product should be selected only where the 0 C to 70 C temperature range and the verified electrical limits match the target system requirements. This page combines verified distributor and manufacturer-linked data with application guidance, design considerations, and a package-focused product summary for engineers evaluating RS-232 interface implementations.

RFQ Contact
MAX232DG4 - 2/2 RS-232 Transceiver 120kbps | Texas Instruments
MAX232DG4

MAX232DG4 - 2/2 RS-232 Transceiver 120kbps | Texas Instruments

The Texas Instruments MAX232DG4 is a 2/2 full-duplex RS-232 transceiver rated for data rates up to 120 kbit/s, operating from a 4.5 V to 5.5 V single supply in a 16-pin SOIC package. It provides two EIA-232 drivers, two receivers, on-chip charge-pump capacitors, and receiver input protection to ±30 V. An RS-232 transceiver is an interface IC that converts between single-ended digital logic levels and balanced, bipolar EIA-232 signal levels. This level-shifting function belongs to the interface-IC hierarchy and is essential when connecting a 5 V microcontroller, processor, or data terminal to an RS-232 port whose logic levels use positive and negative voltages. Key features include operation from one 4.5 V to 5.5 V supply, integrated 1.0 µF charge-pump capacitors, support for data rates to 120 kbit/s, ±30 V receiver input levels, and low typical supply current of 8 mA. Two driver and two receiver channels allow two communication links or hardware flow-control signals to be implemented in one package. The device is intended for industrial and commercial systems operating from 0°C to 70°C. Technically, the charge-pump circuitry generates the negative voltage required by an RS-232 transmitter from the positive supply. Receivers translate bipolar line voltages into CMOS-compatible logic levels, while the specified ±30 V input tolerance helps manage transient exposure on externally routed cables. Because this is a legacy interface rather than a modern differential bus, grounding, cable routing, and protection remain important system-level concerns. Typical uses include service and test equipment, industrial controllers, point-of-sale equipment, data acquisition systems, and embedded serial-port adapters. The MAX232DG4 is most appropriate where two RS-232 channels are useful and a 5 V supply is available. It is not suitable for voltage-mode RS-485 or RS-422 networks, and its 120 kbit/s maximum data rate is adequate for legacy serial ports rather than high-speed physical-layer protocols. The principal design consideration is charge-pump capacitor placement. The integrated capacitors still require correct bypassing and routing around the device, while protected RS-232 lines should be kept away from clocks and sensitive analog signals. Confirm line direction, connector polarity, and the target baud rate before layout because the package contains both transmitters and receivers. This page consolidates distributor data, cross-reference information, and practical RS-232 design guidance. The MAX232DG4 provides a practical solution for two-channel RS-232 conversion in a compact 16-SOIC. Its integrated charge pump removes the need for external voltage-generation components, while 120 kbit/s operation and ±30 V receiver tolerance make it suitable for established EIA-232 equipment. Designers should still account for cable transients, grounding, baud-rate margin, and connector signal mapping. For systems requiring galvanic isolation, modern differential buses, or operation beyond 120 kbit/s, a different interface architecture is required.

RFQ Contact
MAX232DR - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI (Tape & Reel)
MAX232DR

MAX232DR - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI (Tape & Reel)

The Texas Instruments MAX232DR is a 5V-powered, dual-driver / dual-receiver RS-232 transceiver that integrates an on-board capacitive charge-pump to generate the +/-9V TIA/EIA-232-F signaling voltages from a single 5V supply, delivered in a 16-pin SOIC (D) package. It supports data rates up to 120 kbps, accepts +/-30V input levels on the receiver inputs, and supplies 8 mA typical quiescent current from a 4.5V to 5.5V supply rail. The device is functionally designed to be interchangeable with the industry-standard Maxim MAX232 die. A dual EIA-232 (RS-232) line driver/receiver is an interface IC that bridges TTL/CMOS logic levels (0-5V) and the much higher bipolar voltage swings (+/-5V to +/-15V) required by legacy serial-port standards. By generating these higher rails internally from a single low-voltage supply, dual RS-232 transceivers eliminate the need for a separate negative or high-voltage power rail, simplifying board design and reducing BOM cost. In the broader product hierarchy, the MAX232DR belongs to the EIA-232 transceiver family (RS-232 transceiver), then to the Interface ICs category, then to Integrated Circuits, ultimately serving as an enabler of UART-to-DB9 connectivity in microcontroller- and FPGA-based systems. Key features of the MAX232DR include TIA/EIA-232-F and ITU V.28 compliance, +/-30V receiver input tolerance that survives mis-wired cables and transients, an integrated 5V-to-+/-10V charge pump with four external 1 uF capacitors (charge-pump flying capacitors), two drivers and two receivers in a single 16-pin SOIC package, and ESD protection on the RS-232 bus pins (per the family spec). The 120 kbps data rate is more than adequate for serial console, modem, and industrial telemetry traffic, while the wide 4.5V to 5.5V supply range accommodates standard 5V regulated rails and battery-powered designs with headroom. Architecturally, the charge pump uses a voltage-doubler plus an inverting charge pump clocked from an internal oscillator (typically 125 kHz to 250 kHz range), which provides the +10V and -10V rails that drive the RS-232 output stages. The receivers use Schmitt-trigger inputs with hysteresis for noise immunity on long cables. Compared to using a discrete transistor-based level shifter or a +-12V linear supply, the MAX232DR solution occupies roughly 30 mm x 6 mm of board area and removes one power supply from the design. Typical applications include microcontroller UART-to-RS-232 conversion on serial ports of industrial PLCs, point-of-sale (POS) terminals, embedded debug consoles for firmware development, and legacy PC RS-232 COM ports. The MAX232DR is also commonly deployed in factory automation where 5V microcontrollers need to drive RS-232-controlled motor drives or sensors. Other uses include test and measurement equipment (scopes and analyzers with serial ports), legacy networking gear with DB-9 management ports, and education/development boards (Arduino shield, FPGA dev kit UART bridges). When designing with the MAX232DR, observe charge-pump capacitor polarity: TI recommends 1 uF (or larger) low-ESR ceramic capacitors on each of the four charge-pump pins (C1+, C1-, C2+, C2-, V+, V-). Place the capacitors as close to the IC as possible to minimize parasitic resistance and ringing. Avoid long cable stubs on T1OUT/T2OUT pins, and add TVS diodes for additional ESD protection if the application involves frequent cable mating/unmating. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MAX232DRE4 - Dual RS-232 Transceiver, 120 kbit/s | TI
MAX232DRE4

MAX232DRE4 - Dual RS-232 Transceiver, 120 kbit/s | TI

Texas Instruments MAX232DRE4 is a dual RS-232 driver/receiver transceiver with two drivers and two receivers, a 4.5 V to 5.5 V single-supply range, and data rates up to 120 kbit/s. It is packaged in a 16-pin SOIC for industrial-control, instrumentation, and legacy serial-interface equipment. An RS-232 transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into balanced RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, providing physical-layer conversion for UART, serial-port, and point-to-point communication systems. It simplifies the interface by generating the positive and negative RS-232 voltages from one 5 V supply. The MAX232DRE4 supports operation from 4.5 V to 5.5 V, data rates up to 120 kbit/s, and receiver input levels as high as ±30 V. Its typical supply current is 8 mA, while 500 mV receiver hysteresis improves noise immunity at the logic threshold. The commercial-temperature version operates from 0°C to 70°C and is available in a 16-SOIC package. The device uses charge-pump capacitors to produce the bipolar voltage swings required by RS-232. Its two driver channels translate TTL outputs into RS-232 levels, while its two receiver channels perform the inverse conversion. This architecture suits point-to-point links where full-duplex communication and deterministic logic-level interfacing are required without adding a separate external power-supply circuit. Typical uses include RS-232 ports on industrial controllers, laboratory instruments, barcode readers, data-acquisition equipment, service interfaces, and embedded systems that retain a legacy serial connector. The 120 kbit/s maximum rate provides ample margin for configuration consoles, control commands, firmware downloads, and low-to-moderate-rate telemetry. PCB design should prioritize short connections between the charge-pump capacitors, supply pins, and device ground. Place the required 1.0 µF capacitors close to their associated pins, use a solid ground plane, and keep the RS-232 connector interface area physically separated from sensitive analog circuitry to reduce ESD and surge-related coupling. This page combines electrical specifications, package and application guidance, practical layout considerations, and a structured comparison with verified same-family and cross-brand alternatives. It is intended to help engineers evaluate MAX232DRE4 for a new RS-232 design or determine whether an existing 16-SOIC board can be supported by a pin-compatible replacement.

RFQ Contact
MAX232DRG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232DRG4

MAX232DRG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DRG4 is a 5 V dual RS-232 transceiver IC with two drivers and two receivers, a maximum signaling rate of 120 kbps, and a 16-pin SOIC package. It generates the bipolar RS-232 voltage levels required by EIA/TIA-232 equipment from a single 5 V supply. A RS-232 transceiver is an interface IC that converts between digital logic levels and the bipolar voltage signaling used by serial-port equipment. The MAX232 belongs to the broader line-driver and line-receiver hierarchy, where the driver translates TTL or CMOS logic into RS-232 levels and the receiver converts transmitted RS-232 levels back into logic-compatible signals. This makes it a practical interface between a modern microcontroller UART and legacy RS-232 equipment. The MAX232 provides two transmit channels and two receive channels, allowing one RS-232 port to support full-duplex communication. Its stated maximum data rate is 120 kbps, while its 4.5 V to 5.5 V single-supply operating range supports conventional 5 V digital systems. According to the Texas Instruments product page, the device supports output voltages of positive and negative 9 V and includes positive and negative 2 kV ESD protection on the RS-232 pins. Internal charge-pump circuitry generates the positive and negative voltages required by RS-232 from the 5 V supply, eliminating the need for a separate positive and negative supply in many designs. The drivers and receivers are designed to interface UART controllers with external data-terminal equipment while maintaining logic-compatible digital-side signaling. Its dual-channel arrangement makes it suitable for point-to-point links, equipment control, configuration interfaces, and service ports. Typical uses include industrial controller serial ports, data acquisition systems, test equipment, maintenance interfaces, and communications links between a microcontroller and an RS-232 peripheral. The 120 kbps rate is appropriate for legacy serial protocols rather than high-speed differential buses such as RS-485. Cable length, capacitance, grounding, and signal integrity should be evaluated when designing longer interconnects. For a new layout, route the RS-232 driver outputs and receiver inputs directly to the connector while maintaining the separation recommended for exposed interfaces. Place charge-pump capacitors and interface bypass capacitors close to the device, follow the manufacturer pin description when assigning connector signals, and confirm supply tolerances, grounding, and ESD requirements before releasing the PCB. This page combines manufacturer product information, explicit distributor specifications, package-aware alternatives, and practical interface-design guidance to support component selection, schematic review, PCB implementation, and sourcing decisions for the MAX232DRG4.

RFQ Contact
MAX232DW - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX232DW

MAX232DW - 120kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DW is a dual RS-232 driver and receiver with two drivers, two receivers, a 120 kbit/s data rate, and a 16-pin SOIC package. It operates from a single 5 V supply and uses an on-chip capacitive voltage generator to produce the bipolar voltage levels required by TIA/EIA-232-F interfaces. Its approximately ±9 V driver output and ±2 kV ESD protection make it a standard choice for converting between 5 V TTL/CMOS logic and RS-232 signal levels. An RS-232 transceiver is an interface IC that bridges a digital logic system and a serial communications port using the voltage-defined RS-232 standard. The MAX232 belongs to the RS-232 transceiver hierarchy, where a line driver converts TTL/CMOS inputs into bipolar RS-232 outputs and a line receiver converts bipolar inputs into TTL/CMOS levels. This allows equipment with a 5 V UART or microprocessor interface to communicate with legacy RS-232 ports without implementing discrete level-shifting networks. Key features include two transmit channels, two receive channels, operation to 120 kbit/s, a typical 8 mA supply current, receiver input capability of ±30 V, and compatibility with TIA/EIA-232-F and ITU Recommendation V.28. The receiver has a typical transition threshold of 1.3 V and typical hysteresis of 0.5 V. These characteristics provide noise margin and stable interpretation of the bipolar RS-232 signal while retaining the familiar ±9 V driver levels. The device combines four RS-232 signal-conditioning channels with an on-chip charge-pump voltage generator. Charge-pump capacitors connected to the designated voltage-generator pins create the positive and negative supply levels needed by the drivers. This architecture eliminates the negative power supply otherwise required by many discrete RS-232 implementations, while the receiver side provides the electrical translation needed to protect and interface a 5 V logic device. Typical uses include industrial serial consoles, point-of-sale equipment, data-acquisition systems, test and measurement instruments, service interfaces, and legacy peripheral connections. A microcontroller can connect its UART TX and RX signals to the appropriate driver and receiver channels, while the external RS-232 connector receives the bipolar line outputs. The 120 kbit/s capability covers many legacy control and communications protocols without requiring a high-speed RS-485 interface. The principal design consideration is the charge-pump capacitor network and RS-232 connector routing. Capacitors must be connected exactly as required by the manufacturer datasheet, and external line protection should be evaluated for the target cable length and environment. Logic levels and signal polarity must also be checked at each UART channel because the MAX232 provides level conversion, not automatic inversion or protocol handling. This product page consolidates the verified manufacturer specifications, distributor availability, cross-reference information, and engineering guidance for MAX232DW. It also distinguishes a genuine same-package replacement from devices with different charge-pump capacitor requirements or package dimensions, helping engineers avoid substitutions that require PCB or component changes.

RFQ Contact
MAX232DWE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232DWE4

MAX232DWE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DWE4 is a dual RS-232 transceiver containing two EIA-232 drivers and two receivers, operating from a single 5 V supply in a 16-SOIC package. It supports data rates up to 120 kbit/s, accepts receiver input levels of ±30 V, and uses 1.0-mF charge-pump capacitors. The device is recommended for V.28 interfaces and provides 8 mA typical supply current. An RS-232 transceiver is an interface IC that converts between digital logic levels and the voltage-domain signals used by RS-232 equipment. The MAX232 belongs to the RS-232 transceiver hierarchy within interface ICs and broader semiconductor signal-conditioning devices. Its transmitters boost logic signals to RS-232 levels, while its receivers convert bipolar RS-232 inputs into logic-compatible outputs. This makes the device suitable for connecting older serial equipment, control systems, and industrial peripherals to microcontrollers or microprocessors. Key features include two driver channels, two receiver channels, operation from a single 5 V supply, and data-rate support up to 120 kbit/s. The receiver input can withstand ±30 V levels, which improves compatibility with RS-232 ports that may expose unused or externally connected signal lines. According to the manufacturer datasheet, ESD protection exceeds the JESD 2000-V human-body-model requirement. The commercial temperature designation is 0°C to 70°C. The MAX232 uses an on-chip charge-pump voltage converter to generate the positive and negative voltages required by RS-232 drivers from the single 5 V supply. External charge-pump capacitors support this conversion, allowing the complete interface to fit in a standard 16-SOIC footprint. Two drivers and two receivers provide four active interface channels in one package, reducing board area compared with discrete level-shifters and simplifying software control of multiple serial lines. Typical applications include RS-232 console connections, industrial serial adapters, point-of-sale equipment, test and measurement instrumentation, and legacy peripheral interfaces. The 120 kbit/s capability is suitable for moderate-speed serial links rather than high-bandwidth data protocols. Its integrated two-channel transmit and receive arrangement also fits systems that require bidirectional communication over two RS-232 ports. PCB layout should keep charge-pump capacitors close to their associated pins, provide a low-impedance ground connection, and route driver outputs away from sensitive receiver inputs. Confirm the logic levels of the connected host because RS-232 voltage levels are bipolar and not directly compatible with 3.3 V or 5 V CMOS inputs. The 16-SOIC package requires adequate clearance around the exposed leads for soldering and inspection. This page combines the device specifications, commercial sourcing information, verified drop-in alternatives, interface comparisons, and practical PCB guidance to support faster component selection and implementation.

RFQ Contact
MAX232DWG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232DWG4

MAX232DWG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232DWG4 is a dual-channel RS-232 transceiver with two drivers and two receivers, operating from a single 5 V supply at up to 120 kbps in a 16-pin SOIC package. Its integrated charge-pump circuit generates the positive and negative voltages required by RS-232, while the driver outputs swing to approximately ±9 V. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a RS-232 port. It belongs to the hierarchy of interface ICs, communication transceivers, line-interface ICs, and semiconductor signal-conditioning devices. This bidirectional level translation allows equipment using 0 V to 5 V logic to communicate with legacy computers, industrial controllers, test equipment, and other peripherals that use voltage-based RS-232 signaling. The MAX232DWG4 combines four interface functions in one package: two transmit drivers and two receive channels. It supports data rates through 120 kbps, accepts input levels as high as ±30 V, and provides ±2 kV electrostatic-discharge protection. Typical supply current is 8 mA, making it practical for battery-operated instruments, portable test equipment, and embedded control systems where continuous power consumption must remain low. Its internal charge pump uses four external 1.0 µF capacitors to produce the required positive rail and negative rail. The circuit simplifies implementation because the system does not need a separate ±12 V supply. Communication is half-duplex on each channel because a driver and receiver can share the same signal pair, while direction must be controlled by the host if both sides transmit on the same line. Typical uses include serial service ports, industrial configuration interfaces, point-of-sale equipment, modems, embedded instrumentation, and legacy controller connectivity. The MAX232DWG4 is especially useful when the logic side operates at 5 V and the cable side must comply with RS-232 voltage levels. A protected connector and properly routed ground connection remain important because ESD protection does not eliminate the need for good system-level surge protection. During layout, place the four charge-pump capacitors close to their associated pins and provide the decoupling and ground-plane continuity required by the manufacturer datasheet. Keep the logic-side and cable-side routes separated to minimize noise injection. Confirm line-receiver thresholds, driver slew behavior, and cable length against the intended communication standard before releasing a production design. This page combines the MAX232DWG4 specifications, pin assignments, drop-in comparison choices, and practical interface-design guidance. It also highlights charge-pump layout, ESD considerations, application fit, and the distinction between pin-compatible variants so engineers can evaluate replacements without changing the PCB footprint.

RFQ Contact
MAX232DWR - Dual RS-232 Transceiver 120kbps | TI
MAX232DWR

MAX232DWR - Dual RS-232 Transceiver 120kbps | TI

Texas Instruments MAX232DWR is a dual RS-232 line driver and receiver with one 5 V supply, 120 kbit/s operation, ±9 V driver outputs, and ±2 kV ESD protection in a 16-pin SOIC package. The integrated capacitive voltage generator produces the bipolar voltages required by TIA/EIA-232-F and ITU V.28 interfaces, while the two receivers translate bipolar RS-232 signals into TTL/CMOS levels. An RS-232 transceiver is an interface IC that connects low-voltage digital logic to the voltage-tolerant, unbalanced serial signaling defined by EIA/TIA-232. Within the product hierarchy, the MAX232 is a dual driver/receiver, an RS-232 interface transceiver, and ultimately a semiconductor for serial communications and embedded data exchange. This category is especially useful when equipment needs a compact way to bridge a TTL/CMOS UART and an RS-232 port using only a single 5 V rail. Key features include two transmit channels, two receive channels, a maximum data rate of 120 kbit/s, and receiver input capability of ±30 V. Each receiver uses a typical input threshold of 1.3 V with 0.5 V of hysteresis. The MAX232 operates from a single 5 V supply, has a typical supply current of 8 mA, and provides ±9 V RS-232 output levels with ±2 kV ESD protection as stated on the Texas Instruments product page. Technically, the capacitive voltage generator converts the 5 V supply into the positive and negative voltages used by the drivers. The drivers add signal conditioning to create TIA/EIA-232-F output levels, while the receivers convert incoming bipolar signals into logic-compatible levels. This integrated charge-pump approach avoids a separate negative supply rail, but the required charge-pump capacitors and their placement remain important to reliable operation. Typical applications include industrial serial consoles, data acquisition equipment, legacy peripheral adapters, point-of-sale systems, and laboratory instrumentation. The 120 kbit/s rate supports conventional serial links while the ±30 V receiver tolerance helps protect logic-side systems when RS-232 cable noise or ground offsets exceed normal logic levels. The device is especially appropriate where a legacy RS-232 interface must coexist with a modern 5 V UART controller. Designers should follow the manufacturer datasheet for charge-pump capacitor values, receiver input handling, unused-pin configuration, and layout recommendations. Keep the charge-pump loop compact, provide the specified bypass and flyback capacitance, and verify the connected UART voltage levels and grounding before treating the interface as RS-232 compliant. This product page combines verified manufacturer specifications, distributor availability references, same-package replacement analysis, and practical interface-design guidance. It is intended to help engineers confirm electrical compatibility, identify genuine pin-compatible alternatives, and implement a dependable 5 V-to-RS-232 signal path without relying on packaging-only substitutions.

RFQ Contact
MAX232DWRE4 - Dual RS-232 Transceiver | Texas Instruments
MAX232DWRE4

MAX232DWRE4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232DWRE4 is a dual EIA-232 driver and receiver IC providing two transmit channels and two receive channels in a 16-pin SOIC package. It operates from a single 5 V supply, supports data rates up to 120 kbit/s, and accepts RS-232 input levels of ±30 V. The device uses onboard charge-pump capacitors to generate the bipolar voltage required by the RS-232 drivers. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where transceivers combine a transmitter, receiver, and charge-pump circuit into a complete serial-port interface. This integration reduces the number of external components required for legacy serial communication. The MAX232DWRE4 includes two drivers and two receivers, allowing two full-duplex RS-232 links when both directions of each channel are connected. Its recommended V.28 interface supports asynchronous data transmission, while the 120 kbit/s operating rate is suitable for many industrial-control, point-of-sale, instrumentation, and embedded-console interfaces. A typical supply current of 8 mA helps limit system power consumption in equipment with limited thermal budgets. The internal charge-pump design generates positive and negative voltage levels needed by the drivers. The device requires 1.0 µF charge-pump capacitors and operates from one 5 V supply, eliminating the need for a separate bipolar supply. Receiver inputs tolerate ±30 V levels, providing protection margin for RS-232 signals encountered on cables and connected equipment. Its stated ESD protection exceeds JESD-2000-V human-body-model requirements. Typical applications include industrial RS-232 equipment, service-console interfaces, data-acquisition systems, and legacy peripheral connections. The SOIC-16 package is also well suited to through-hole assembly and repair workflows where a surface-mount SOIC remains compatible with existing boards. Because RS-232 is point-to-point, designers should use twisted-pair wiring, controlled ground references, and appropriately terminated shields to reduce noise pickup. Place the 1.0 µF charge-pump capacitors close to their associated pins and connect the device ground directly to the interface ground. Keep RS-232 traces away from sensitive analog and high-speed digital signals, and provide a nearby low-impedance bypass connection from VCC to ground. These measures reduce switching-generated noise and help preserve receiver signal integrity. This page combines electrical specifications, application guidance, package details, and pin-compatible replacement options for faster engineering evaluation. It also highlights the distinctions that matter when deciding whether a MAX232-family part, an enhanced charge-pump transceiver, or another RS-232 implementation best matches a new or existing design.

RFQ Contact
MAX232DWRG4 - Dual 120kbps RS-232 | Texas Instruments
MAX232DWRG4

MAX232DWRG4 - Dual 120kbps RS-232 | Texas Instruments

Texas Instruments MAX232DWRG4 is a 5 V dual-channel RS-232 line transceiver with 120 kbps data rate, ±9 V driver output, and ±2 kV ESD protection, housed in a 16-pin SOIC package. The device combines two line drivers and two line receivers, allowing bidirectional serial communication between TTL/CMOS logic and an EIA/TIA-232 link. An RS-232 transceiver is an interface IC that translates low-voltage digital logic levels into the positive and negative voltage levels used by RS-232 equipment. Within the interface hierarchy, it belongs to the line-driver and line-receiver family, provides physical-layer signal conditioning, and bridges a host controller or UART with an external data port. Key features include a single 5 V supply, operation up to 120 kbps, ±9 V driver output levels, and ±2 kV ESD protection. The integrated dual-driver and dual-receiver configuration supports two communication channels in one package. Its commercial-grade operating range is 0°C to 70°C, making it appropriate for room-temperature industrial, instrumentation, and embedded-control systems. The MAX232DWRG4 uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 from one 5 V supply. Its receiver converts incoming EIA-232-F signals into TTL/CMOS-compatible levels, while its driver converts outgoing logic levels into RS-232 signals. The interface conforms to EIA-232-F, TIA-232-F, and V.28 requirements identified for this device. Typical uses include industrial control panels, serial test equipment, data acquisition systems, point-of-sale terminals, and embedded RS-232 ports. Its 120 kbps capability is suitable for moderate-speed point-to-point links, although modern high-speed or long-distance designs may require a more suitable RS-232 transceiver family. PCB implementation should follow the manufacturer pin-description and capacitor-connection diagrams. Place charge-pump capacitors close to their specified pins, keep RS-232 routing away from sensitive analog and high-speed clock traces, and provide suitable logic-side ground return paths. The external RS-232 connector may also require additional transient-protection measures for exposed cables. This page combines the manufacturer’s principal electrical ratings with package details, interface standards, replacement guidance, and practical layout considerations. It is intended to help engineers evaluate the MAX232DWRG4 for 5 V RS-232 designs and identify compatible second-source options without changing the 16-pin SOIC footprint.

RFQ Contact
MAX232ECD - 5V Dual RS-232 Driver/Receiver | Texas Instruments
MAX232ECD

MAX232ECD - 5V Dual RS-232 Driver/Receiver | Texas Instruments

The Texas Instruments MAX232ECD is a dual RS-232 driver/receiver IC that operates from a single 5V supply and includes integrated IEC61000-4-2 ESD protection on the RS-232 lines. Housed in a 16-pin SOIC (D) package, the device integrates a capacitive voltage-doubler/inverter charge pump that generates the ±10V RS-232 voltage levels from a single 5V rail using four external 1.0 µF capacitors, eliminating the need for a dual-polarity supply. Each part contains two line drivers and two line receivers, supporting full-duplex RS-232 communication at data rates up to 120 kbit/s with ±30V input tolerance on receiver inputs. An RS-232 line driver/receiver (also called a transceiver) is a type of interface IC that bridges the voltage gap between TTL/CMOS logic (0V-5V) and the TIA/EIA-232-F standard (±5V to ±15V swing). It belongs to the broader hierarchy of line drivers -> interface ICs -> integrated circuits -> semiconductors. The MAX232 family is the de-facto industry-standard solution for asynchronous serial-port level translation and is found in nearly every embedded design that needs RS-232 connectivity. Key features include integrated IEC61000-4-2 ESD protection (typically ±15kV air-gap, ±8kV contact discharge on the RS-232 pins), low supply current of typically 8 mA with no load, and 1.0 µF charge-pump capacitors (versus the original MAX232 which used 1.0 µF; the MAX232E and MAX232EC variants retain the same capacitor requirement). The 'C' suffix indicates the commercial 0°C to +70°C operating temperature range. The wide ±30V receiver input range tolerates mis-wired or shorted RS-232 cables without permanent damage. The MAX232ECD uses a charge-pump architecture based on a switched-capacitor voltage doubler and voltage inverter. An internal oscillator (typically 125 kHz) drives the charge pump; the doubled +10V (V+) and inverted -10V (V-) rails feed the driver output stage, while the receiver section operates from the single 5V supply with internal 5 kΩ pull-down resistors. This architecture eliminates the bulky ±12V supplies historically required for RS-232 interfaces. Typical applications include industrial PLC serial ports, point-of-sale (POS) terminals, embedded microcontroller debug consoles, legacy PC COM-port replacements via USB-to-serial bridges, and any design requiring TIA/EIA-232-F compliance. The integrated IEC61000-4-2 ESD protection makes the MAX232ECD especially suitable for cables exposed to user contact or industrial ESD events. When designing with this device, place the four charge-pump capacitors (typically 1.0 µF ceramic) as close to the C1+, C1-, C2+, C2- pins as possible. Although the integrated ESD protection is robust, external TVS diodes are still recommended for the most demanding industrial environments. The MAX232ECD is pin-compatible with the industry-standard MAX232 and may be used as a drop-in upgrade in most existing designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - including a parametric comparison versus the MAX3232E, ADM232, and HIN232 families and verified IEC61000-4-2 ESD ratings not always quoted in the datasheet's electrical characteristics table.

RFQ Contact
MAX232ECDR - Dual RS-232 Driver/Receiver, ESD-Protected | TI
MAX232ECDR

MAX232ECDR - Dual RS-232 Driver/Receiver, ESD-Protected | TI

The Texas Instruments MAX232ECDR is a dual RS-232 driver/receiver with integrated IEC 61000-4-2 ESD protection, packaged in a 16-pin SOIC. It operates from a single 5 V supply using 1.0 µF charge-pump capacitors, supplies 2 drivers and 2 receivers, supports data rates to 120 kbit/s, and tolerates ±30 V input levels. The 'E' suffix denotes the enhanced ESD-protected version (HBM ±15 kV, IEC 61000-4-2 contact/air ±8 kV/±15 kV). What is an RS-232 transceiver? An RS-232 transceiver is a type of serial interface IC that translates logic-level (0 V/5 V or 0 V/3.3 V) signals on the TTL/CMOS side to bipolar RS-232 voltage levels (typically ±5 V to ±15 V) required by the TIA/EIA-232-F standard. RS-232 transceivers sit inside the interface ICs family, between UART/SCI controllers and external DB9/DB25 connectors, enabling legacy PC and industrial serial communication. The MAX232 family historically integrated charge-pump doublers/inverters to generate ±10 V from a single +5 V rail, eliminating the need for a dual supply. Key features of the MAX232ECDR include on-chip ±10 V generation from a single 5 V supply via four external 1.0 µF charge-pump capacitors, ±30 V receiver input tolerance that exceeds the TIA/RS-232-F specification, low supply current (typically 8 mA), and TTL/CMOS-compatible logic I/O. The integrated IEC 61000-4-2 ESD protection on the RS-232 lines eliminates external TVS arrays in most designs, reducing BOM cost and PCB area. The device operates across the commercial 0 °C to 70 °C temperature range. The MAX232ECDR uses a CMOS charge-pump voltage doubler/inverter architecture: an internal oscillator drives an external capacitor network that produces V+ (≈ +10 V) and V− (≈ −10 V) rails from the +5 V supply. Drivers translate TTL inputs to RS-232 levels (5 V → +10 V for a mark, 0 V → −10 V for a space); receivers invert and level-shift incoming RS-232 signals back to TTL. The 120 kbit/s data rate supports standard serial links including legacy modems, point-of-sale terminals, and industrial PLC links. Typical applications include factory automation PLCs and industrial control RS-232 ports, point-of-sale (POS) terminals, legacy PC COM ports and peripherals (mice, barcode scanners), embedded microcontroller UART bridges, and instrumentation serial links. The integrated ESD protection makes it especially suitable for handheld and field-exposed equipment where IEC 61000-4-2 air-discharge events are routine. When designing with this part, place the four 1.0 µF charge-pump capacitors as close as possible to the C1+, C1−, C2+, C2− pins to minimize ripple and EMI. Note that VCC must rise monotonically and quickly to ensure proper charge-pump startup; an RC delay on VCC is not recommended. Receiver inputs tolerate ±30 V even when VCC = 0 V (true fail-safe), simplifying hot-plug and powered-down interfaces. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, IEC 61000-4-2 design guidance, and comparator pinout notes not consolidated on the manufacturer datasheet front page.

RFQ Contact
MAX232ECDW - 250kbps RS-232 Transceiver | Texas Instruments
MAX232ECDW

MAX232ECDW - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232ECDW is a dual RS-232 driver and dual receiver interface IC that supports data rates up to 250 kbps from a 4.5V to 5.5V supply. It is housed in a 16-pin SOIC package and includes IEC 61000-4-2 electrostatic-discharge protection. A MAX232 device is a bipolar RS-232 interface transceiver that converts logic-level signals between TTL/CMOS equipment and the positive and negative voltage levels used by RS-232 links. Within the interface IC hierarchy, the MAX232 belongs to the line-driver and line-receiver family, bridging a digital controller or computer port and a physical serial communication cable. The MAX232ECDW integrates two transmit channels and two receive channels, allowing two bidirectional RS-232 ports or one port plus additional point-to-point links to be supported by one device. Its specified operating supply range is 4.5V to 5.5V, and its maximum signaling rate is 250 kbps. IEC 61000-4-2 protection adds electrostatic-discharge resilience to a frequently touched external interface. Internally, the device uses a charge-pump voltage generator to produce the bipolar RS-232 voltage levels required by the drivers while operating from a single low-voltage supply. The receivers convert bipolar RS-232 inputs to TTL and CMOS logic levels, with a typical receiver threshold of 1.3V according to the manufacturer datasheet. Together, the dual-channel arrangement and 250 kbps capability suit control, instrumentation, industrial communication, and legacy computer interfaces. Typical uses include service-console connections, factory equipment interfaces, laboratory instruments, embedded serial bridges, and industrial controllers that retain an RS-232 port. The device is appropriate when a system requires full RS-232 rather than TTL logic levels, particularly for cable connections where voltage polarity, ground reference, and ESD exposure must be considered. A robust layout should place the charge-pump capacitors and supply-decoupling capacitors close to their associated pins, while keeping protected connector-side traces away from sensitive logic. External protection and signal-conditioning components may still be needed when the connected cable is long or the port is exposed to severe industrial transients. This page consolidates the principal electrical characteristics, package details, drop-in replacement candidates, application guidance, and design cautions engineers need when evaluating the MAX232ECDW for an RS-232 interface.

RFQ Contact
MAX232ECDWR - Dual 250kbps RS-232 Transceiver | Texas Instruments
MAX232ECDWR

MAX232ECDWR - Dual 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232ECDWR is a dual RS-232 line driver and receiver with IEC 61000-4-2 electrostatic-discharge protection. It supports a 4.5V to 5.5V supply, operates at up to 250kbps, and is packaged in a 16-pin SOIC. The device includes on-chip charge-pump circuitry for generating the bipolar RS-232 voltage levels required by the transmitters. An RS-232 transceiver is an interface IC that converts between single-ended TTL and CMOS logic levels and the differential, bipolar signaling used by RS-232 equipment. Its transmitters provide level shifting and signal conditioning for outgoing data, while its receivers translate incoming RS-232 signals into logic-compatible levels. The MAX232ECDWR combines two transmitters and two receivers in one package, making it suitable for two-way serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment. Key electrical characteristics include operation from a 4.5V to 5.5V single supply and a maximum signaling rate of 250kbps. IEC 61000-4-2 protection is a distinguishing feature for cables and connectors that may be exposed to electrostatic discharge. The 16-pin SOIC package follows the familiar MAX232E pin arrangement, including dedicated charge-pump capacitor pins and a bypass-capacitor connection. These external capacitors must be selected according to the manufacturer datasheet rather than substituted with arbitrary values. The MAX232E architecture uses a capacitive voltage generator to produce the positive and negative voltage levels required for RS-232 transmission. Because this charge-pump architecture needs external capacitors, board layout should keep the charge-pump network compact and place bypass capacitance close to the supply pins. The receiver side converts bipolar RS-232 input levels to CMOS logic levels, allowing the device to interface directly with a host UART or other digital controller. Typical applications include RS-232 ports on industrial test equipment, programmable logic controllers, serial adapters, point-of-sale terminals, laboratory instruments, and embedded control boards. The 250kbps rate is suitable for legacy serial peripherals, configuration links, and short-distance point-to-point communication. The integrated ESD protection is particularly useful where an exposed DB9 or equivalent connector connects the transceiver to external cables. When designing the board, verify the required charge-pump and bypass capacitor values in the manufacturer datasheet and confirm that the 4.5V to 5.5V supply remains within tolerance during transients. Keep protected connector-side routing separated from sensitive logic-side traces, and provide a controlled ground reference between communicating systems to avoid unintended signal offsets. This page combines the exact MAX232ECDWR ordering information, electrical characteristics, cross-reference findings, PCB implementation guidance, and application-specific engineering guidance for engineers evaluating the SOIC-16 transceiver for RS-232 interfaces.

RFQ Contact
MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX232ECDWRE4

MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232ECDWRE4 is a +5 V dual RS-232 driver and receiver that provides two transmit channels and two receive channels in a 16-pin SOIC package. It supports data rates up to 250 kbps across a 4.5 V to 5.5 V supply range. Its integrated capacitive voltage generator uses four capacitors to produce the bipolar voltage levels required by TIA/EIA-232-F interfaces from a single 5 V supply. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential, bipolar RS-232 signals. It belongs to the serial-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → communication semiconductor. This conversion allows equipment with a logic-level UART to connect to computers, industrial controllers, test equipment, and other RS-232 endpoints through a protected physical interface. The MAX232ECDWRE4 combines two RS-232 drivers, two receivers, and the charge-pump voltage generator in one package. All RS-232 pins feature 15 kV HBM and 15 kV IEC 61000-4-2 air-gap discharge protection, while RS-232 pins also provide 8 kV IEC 61000-4-2 contact-discharge protection. These ratings make the device appropriate for exposed serial ports where electrostatic discharge is a practical concern. The charge-pump architecture creates positive and negative RS-232 levels without a negative supply rail. Its four external charge-pump capacitors determine the required energy-transfer behavior and must be placed close to their associated pins. The receiver converts incoming TIA/EIA-232-F signals into 5 V TTL/CMOS levels, while the drivers convert TTL/CMOS inputs into compliant RS-232 output levels. The MAX232E family is optimized for operation from a single +5 V supply. Typical uses include legacy industrial serial consoles, programmable test equipment, point-of-sale peripherals, data acquisition systems, and service interfaces embedded in larger control systems. The 250 kbps maximum data rate supports moderate-speed asynchronous links rather than high-bandwidth differential serial protocols. Full-duplex operation allows a port to transmit and receive simultaneously through independent channels. PCB design should prioritize short traces from the charge-pump capacitors to pins 1 and 4, as specified by the Texas Instruments MAX232E datasheet. Keep the interface connector and transceiver pins away from sensitive analog or high-speed digital nodes, and route the ground return with the RS-232 signal path to reduce noise pickup. A common-mode choke can be added when cable emissions or susceptibility become significant. This page combines the manufacturer interface specifications, protection ratings, package details, verified sourcing information, drop-in alternatives, and practical layout guidance in one engineering-focused reference for evaluating the MAX232ECDWRE4 in +5 V RS-232 designs.

RFQ Contact
MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments
MAX232ECDWRG4

MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments

Texas Instruments MAX232ECDWRG4 is a dual RS-232 driver and receiver interface IC with two transmit channels, two receive channels, and IEC 61000-4-2 protection. It operates from a single 5 V supply, supports data rates to 120 kbit/s, accepts input levels to ±30 V, and uses 1.0 uF charge-pump capacitors. The device is packaged in a 16-pin SOIC. An RS-232 transceiver is an interface circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, which combines drivers, receivers, charge-pump voltage conversion, and transient protection in one semiconductor package. The MAX232ECDWRG4 includes two drivers and two receivers, allowing one package to support two RS-232 communication channels. Its single 5 V supply architecture simplifies system power planning, while the integrated charge pump generates the positive and negative voltages required by RS-232 drivers. Operation up to 120 kbit/s makes the device appropriate for legacy serial ports, industrial control links, equipment interfaces, and embedded systems using compatible RS-232 protocols. IEC 61000-4-2 protection is a key feature for connectors exposed to electrostatic discharge. The protection capability helps reduce system susceptibility to ESD events at the interface boundary, although it does not eliminate the need for correct grounding, cable design, and connector placement. The input circuitry tolerates levels to ±30 V, supporting the voltage stress commonly encountered on RS-232 networks. Typical uses include PC-compatible serial ports, test equipment, security systems, instrumentation, industrial controllers, and point-of-sale equipment. Two complete driver-receiver sections can also support separate transmit and receive paths or more than one RS-232 port when several devices share the same PCB. The 16-pin SOIC package supports conventional surface-mount assembly and is easy to route on standard industrial-control boards. Place the two 1.0 uF charge-pump capacitors close to their designated pins, connect the supply and ground pins to low-impedance planes, and route the RS-232 traces away from sensitive analog signals. Confirm that the external capacitor voltage rating and dielectric are suitable for the charge-pump waveform. PCB power and ground handling should account for the charge pump's switching current even though the interface itself is designed for a single 5 V rail. This product overview combines the verified electrical capabilities, package details, interface standards, application guidance, replacement considerations, and practical layout notes needed to evaluate the MAX232ECDWRG4 for an RS-232 design. It also highlights the distinction between direct pin-compatible replacements and broader functional alternatives when maintaining an existing circuit board.

RFQ Contact
MAX232ECNG4 - Dual RS-232 Transceiver | Texas Instruments
MAX232ECNG4

MAX232ECNG4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232ECNG4 is a dual RS-232 transceiver with one driver and one receiver per channel, integrated ESD protection, and a 16-pin plastic dual in-line package measuring 0.300 inch by 0.300 inch with a 7.62 mm body width. It is designed for systems that require bidirectional RS-232 conversion between modern digital logic and older serial interfaces. An RS-232 transceiver is an interface IC that translates low-voltage CMOS or TTL-compatible logic levels to and from the higher-voltage bipolar signaling used by RS-232. A complete interface path commonly includes a transceiver for the main serial connection, a driver for additional lines, and a receiver for incoming data. The MAX232ECNG4 belongs to the RS-232 interface level within the broader semiconductor and interface IC hierarchy. The principal feature of the MAX232ECNG4 is its integrated 2-transceiver arrangement. One channel can transmit while the other receives, allowing full-duplex communication with only two device channels. Integrated ESD protection is particularly useful at exposed connector pins, where static discharge from cables and connected equipment can damage a communications interface. The through-hole 16-pin package also supports conventional PCB assembly and connector-routing layouts. This device is associated with the MAX232 product family from Maxim, which was acquired by Analog Devices and is now offered through Texas Instruments. The ECNG4 ordering code identifies the specific commercial-temperature, 16-pin plastic DIP configuration. Exact electrical ratings, driver and receiver thresholds, charge-pump performance, supply limits, and environmental classifications must be confirmed in the manufacturer datasheet before the circuit is released for production. Typical uses include industrial control consoles, data-acquisition equipment, test systems, service interfaces, and embedded serial ports. The MAX232ECNG4 can also pair with dedicated RS-232 line drivers or receivers when a system requires more than two channels or an RS-485-to-RS-232 conversion stage. Connection to a modern host generally requires a logic-level UART, while the opposite side connects to an RS-232 connector and its external signal ground. The principal design consideration is ensuring the transceiver operates with valid logic levels and supply voltage throughout startup, data transmission, and cable disconnection. Decoupling capacitors, cable routing, signal-ground handling, and ESD exposure all affect reliability. Confirm the required charge-pump capacitor values, driver slew behavior, receiver thresholds, and maximum data rate in the manufacturer datasheet before finalizing the layout. This product record combines interface identification, package information, application guidance, comparison criteria, and practical design notes. It also distinguishes verified drop-in alternatives by package, temperature grade, and functional fit so engineers can narrow replacements without treating every similar RS-232 transceiver as an automatic substitution.

RFQ Contact
MAX232ECPE+ - 120kbps 5V RS-232 Transceiver | Analog Devices
MAX232ECPE+

MAX232ECPE+ - 120kbps 5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ECPE+ is a dual RS-232 transceiver with one driver and one receiver per channel, operates from a single 4.5V to 5.5V supply, supports data rates through 120kbps, and is packaged in a 16-pin PDIP. Designed for EIA/TIA-232E and CCITT V.28 links, it provides the electrical conversion required between TTL/CMOS logic and balanced RS-232 signals. The integrated charge-pump circuitry generates the required RS-232 voltage levels without a separate negative power supply. An RS-232 transceiver is an interface IC that bridges a digital logic system and a serial communications port. RS-232 uses single-ended, bipolar signaling in which logic levels are represented by positive and negative voltages relative to ground. Within the electronics hierarchy, the MAX232ECPE+ is an interface IC, an RS-232 transceiver, a line driver and receiver pair, and ultimately a semiconductor communication component. It is commonly placed between a UART, microprocessor, controller, or service connector and an external RS-232 port. Key verified features include two transmit channels and two receive channels, operation from one 4.5V to 5.5V supply, and support for data rates up to 120kbps. Distributor and manufacturer-family sources identify the MAX232E line as meeting EIA/TIA-232E and CCITT V.28 requirements when loaded. The device also offers 15kV ESD protection according to distributor descriptions, improving interface robustness against electrostatic discharge encountered during cable connection or industrial use. The MAX232ECPE+ uses integrated charge-pump circuitry to generate the positive and negative voltage levels needed by RS-232 drivers from the single low-voltage supply. Receivers convert the incoming bipolar RS-232 signal into a digital level compatible with the connected logic system. Exact pin names, electrical limits, propagation timing, and capacitor values should be confirmed in the manufacturer data sheet before layout because those details were not included in the supplied verified excerpts. Typical applications include legacy RS-232 service consoles, instrumentation, point-of-sale equipment, industrial controllers, and adapter boards that connect TTL/CMOS UART devices to DB9 or other RS-232 connectors. The 120kbps capability is suitable for moderate-speed serial links, while the 5V supply simplifies integration with established digital systems. For new designs, the MAX233 family may be attractive when eliminating external charge-pump capacitors is more important than retaining the MAX232E footprint and feature set. When designing the interface, connect the charge-pump capacitors and supply bypassing capacitors exactly as specified by the manufacturer. Keep the RS-232 connector-side nets away from sensitive analog and high-speed digital traces, and provide the connector ground as a short, robust return path. ESD protection helps, but it does not replace correct signal routing, chassis grounding, or system-level surge protection. This page combines verified manufacturer and distributor references, cross-reference results, packaging information, application guidance, and design cautions to support faster component selection. It deliberately distinguishes verified electrical facts from values that require confirmation from the complete data sheet, helping engineers avoid treating incomplete search snippets as a substitute for the manufacturer specification.

RFQ Contact