Products (44,000+)

MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices
MAX3097EESE+

MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3097EESE+ is a triple RS-422/RS-485 line receiver with fault detection, 32 Mbps operation, and ±15 kV ESD protection, housed in a 16-pin NSOIC package. The device operates from a 3 V to 5.5 V supply range, with the verified product description specifying 3 V/5 V operation. It accepts three differential receiver inputs and provides fault-status outputs for detecting invalid input states. A line receiver is an interface circuit that converts low-amplitude differential signals into a digital logic-level output. RS-422 and RS-485 are balanced serial-interface standards used to transmit data reliably over cables and through electrically noisy environments. The MAX3097EESE+ belongs to the receiver and interface-IC hierarchy, combining differential signaling, fault indication, and transient protection in one device. Key features include three high-speed receivers, support for both RS-422 and RS-485 signaling, ±15 kV ESD protection, and operation up to 32 Mbps. The fault-detection circuitry indicates when a receiver input is not in a valid state, allowing system software or hardware monitoring logic to identify wiring faults, idle conditions, or abnormal bus states. The 16-pin NSOIC package supports conventional surface-mount PCB assembly. The MAX3097E family is intended for industrial data links, factory equipment, communications interfaces, and other systems that use balanced differential signaling. Its three-channel architecture reduces component count when several receiver channels are required on one board. The ±15 kV ESD rating is particularly relevant to externally connected communication lines, where static discharge and cable-borne transients can damage interface circuitry. Designers should verify the receiver’s fault-status logic, supply sequencing, input termination, and cable configuration against the manufacturer datasheet before production use. Differential receiver inputs should be routed as a matched pair, with appropriate grounding and protection implemented according to the system’s cable environment. The receiver is not a transmitter, so a separate RS-485 driver is required when a design needs bidirectional bus communication. This product page consolidates verified manufacturer and distributor information, pricing references, package details, and application guidance for engineers evaluating the MAX3097EESE+. It is intended as a technical buying and design reference rather than a substitute for the complete manufacturer datasheet.

RFQ Contact
MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices
MAX309EPE+

MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices

The Analog Devices MAX309EPE+ is a dual 4:1 CMOS analog multiplexer with 2 circuits, less than 100 ohm on resistance, 150 ns switching performance, and a 16-pin PDIP package. Its multiplexers support ±5 V to ±30 V and ±20 V signal ranges, depending on the selected supply arrangement. A CMOS analog multiplexer is an interface IC that routes one of several input signals to a shared output under digital control. The MAX309 belongs to the analog switch and multiplexer hierarchy, where it combines bidirectional signal routing, low on resistance, and precise channel matching. Each internal 4:1 circuit uses address logic to select one of four analog inputs for connection to its common output. Key characteristics include on resistance below 100 ohm, channel-to-channel matching within 5 ohm, and on-resistance variation of no more than 7 ohm across the specified analog signal range. The device also provides break-before-make operation and approximately 750 pA of leakage-related current in the cited technical listing. These characteristics support accurate routing of moderate-voltage analog signals without introducing substantial insertion resistance. The MAX309EPE+ is implemented as a precision monolithic CMOS device, with two independently addressed 4:1 sections. Its 150 ns switching figure supports applications requiring fast selection among sensors, measurement channels, or control signals. Matching between channels and flat on resistance across the analog range help preserve signal amplitude and balance when different sources are selected. Typical uses include instrumentation signal selection, data-acquisition systems, industrial control interfaces, test and measurement equipment, and analog signal routing where several sources share a common processing chain. The dual-circuit organization can route two independent signal groups or provide two complementary multiplexed paths on the same board. PCB design should preserve the 16-pin PDIP footprint and route each analog input directly to its intended pin. Keep sensitive analog traces away from digital address and control lines, provide clean supply decoupling, and use short connections to minimize parasitic capacitance. Verify the selected supply and input ranges against the MAX309 datasheet before connecting external signals. This page combines manufacturer product information, distributor listings, same-family drop-in candidates, application guidance, and practical design notes to support component selection and PCB implementation.

RFQ Contact
MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim
MAX310CPE+

MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim

The Maxim Integrated MAX310CPE+ is an 8-channel CMOS RF and video multiplexer packaged in a 16-pin PDIP. It is designed to route multiple RF or video signals through a shared signal path while maintaining a compact through-hole footprint. The device is listed in production by Analog Devices, and the MAX310 family is identified as a CMOS RF/video multiplexer. An RF or video multiplexer is an interface IC that connects several signal sources to one destination or selects one input path for downstream processing. In the signal-chain hierarchy, the MAX310 belongs to analog switches, interface ICs, and broader semiconductor signal-routing systems. Its 8-channel architecture is useful when several sources must be combined or selected without duplicating downstream receivers, tuners, or measurement equipment. The MAX310CPE+ combines an 8-channel multiplexer configuration with CMOS construction and a 16-pin PDIP package. Through-hole mounting makes it suitable for legacy boards, laboratory instruments, educational equipment, prototypes, and industrial systems that use conventional plated-through-hole PCB footprints. The C designation identifies the temperature-grade family, while the E suffix denotes the 16-pin PDIP package in Maxim Integrated's device naming system. The MAX310 family is intended for RF and video signal routing rather than general-purpose logic. Designers must account for the operating-frequency range, insertion loss, isolation, channel capacitance, switch resistance, supply requirements, control logic, and package-level thermal performance when laying out a new board. These electrical characteristics determine whether the multiplexer preserves signal integrity in the intended RF or video environment. Typical uses include RF test systems, video-source selection, broadcast and surveillance equipment, cable-TV signal routing, instrumentation, and educational RF laboratories. In each case, the eight-channel organization can reduce the number of separate switching paths or provide source selection ahead of a common receiver. The MAX310CPE+ is also useful for maintaining older through-hole designs where a surface-mount multiplexer would not fit the existing board. For a new design, confirm the complete pinout and signal ratings in the manufacturer MAX310 datasheet before routing the PCB. Maintain short RF traces, use a controlled reference plane, decouple the supply connection according to the datasheet guidance, and keep high-speed or high-frequency routes away from noisy switching nodes. Validate the finished channel performance with the intended source impedance and termination scheme. This product page combines the MAX310 family identity, exact MAX310CPE+ ordering code, package information, lifecycle indication, sourcing links, and practical implementation guidance. It also distinguishes the true 16-pin PDIP variant from parts that use other packages and identifies why a footprint-compatible replacement must be selected from the pin-description table rather than by function alone.

RFQ Contact
MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices
MAX310CWN+

MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices

The Analog Devices MAX310CWN+ is an 8-channel CMOS RF/video multiplexer in an 18-pin SOIC package. The device provides a single 8:1 multiplexing function for routing video or RF signals, making it suitable for video switching, signal selection, test equipment, and instrumentation systems. The MAX310 family is identified by the manufacturer as a CMOS RF/video multiplexer, while the MAX310CWN+ order code is associated with the 18-SOIC configuration. A multiplexer is a switching component that connects one signal path to one of several possible signal paths. An 8:1 RF/video multiplexer is therefore positioned between multiple source signals and a shared destination, allowing a system to select among eight inputs instead of duplicating downstream amplification and routing circuitry. This is useful in cameras, video test systems, measurement equipment, and other applications where the selected source must remain compatible with the connected receiver. The MAX310CWN+ is identified as a single-channel, 8:1 analog multiplexer. Its CMOS implementation is intended for RF and video signal routing, where low-noise signal handling and predictable channel selection are important. The device is available in an 18-pin SOIC package, a surface-mount package that supports conventional PCB assembly and provides a practical option for compact analog switching systems. The manufacturer product page lists the MAX310 as a production 8-channel CMOS RF video multiplexer and provides the product selection table, data sheet, sample and buy resources, and supporting documentation. The distributor listing describes the MAX310CWN+ as a video switch IC with one channel in an 18-SOIC package. Use the manufacturer data sheet for the exact electrical ratings, control logic, insertion loss, isolation, bandwidth, on-resistance, supply requirements, and pin-level truth table before finalizing a circuit. In a typical design, the selected source is connected to the common output, while the eight input paths are driven by the source being tested or displayed. The device should be placed close enough to the controlled signal sources to minimize board-level interference and trace loss. Keep sensitive video or RF routing on controlled-impedance structures when signal integrity matters, and route control traces away from analog and RF paths where practical. The main design consideration is verification of the exact MAX310CWN+ configuration, including supply voltage, control-pin polarity, and the pinout associated with the 18-SOIC package. Do not assume that a similar MAX310 order code has identical enable logic, pin assignment, or electrical limits. Consult the pin-description table and typical application circuit in the manufacturer data sheet when assigning PCB tracks. This product page organizes the MAX310CWN+ identity, package information, sourcing guidance, alternatives, and application-oriented engineering notes. It is intended to help engineers locate the correct manufacturer documentation and make a documented replacement decision rather than relying only on a generic video-switch description.

RFQ Contact
MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim
MAX310EWN+

MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim

The Maxim Integrated MAX310EWN+ is an 8-channel CMOS RF/video multiplexer with one 8:1 selection path, 250 ohm on-state resistance, and operation from negative or positive dual supplies spanning -16.5 V to -4.5 V and 4.5 V to 16.5 V. The device is packaged in an 18-pin SOIC for surface-mount assembly. A video multiplexer is an interface integrated circuit that routes one of several analog video sources to a shared output. The MAX310EWN+ belongs to the broader RF/video switch and signal-routing hierarchy, where an analog switch or multiplexer selects a source without requiring separate downstream receivers for every input. CMOS construction supports low-power operation and consistent signal-path behavior across negative and positive supply rails. The principal feature set includes eight selectable RF/video channels, a single multiplexed output path, and 250 ohm on resistance. Its ability to operate with either negative or positive supply voltage is useful in systems using bipolar signal paths, legacy video equipment, or mixed analog environments. The industrial temperature grade and surface-mount SOIC package support compact, automated PCB assembly. Signal integrity depends on keeping the selected path short and providing a stable return connection. Although the switch resistance is suitable for many video-routing applications, cable capacitance, source impedance, trace geometry, and the impedance of the connected receiver can influence edge response. Grounding, bypass capacitance, and connector placement should therefore be treated as parts of the complete switching network rather than separate mechanical concerns. Typical uses include analog video source selection, RF test-equipment routing, broadcast and professional video signal routing, instrumentation channel selection, and legacy computer-video interfaces. The MAX310EWN+ is most appropriate when an eight-input multiplexer is required in an 18-pin surface-mount design and when bipolar supply operation matches the surrounding circuitry. For layout, assign each signal pin directly to its corresponding connector or source network, keep the mux input and output routes short, and provide local supply bypassing. Check the complete datasheet for control logic levels, break-before-make behavior, channel capacitance, leakage, and timing before using the device in precision or high-frequency systems. This page consolidates the identified electrical characteristics, package details, functional alternatives, and practical layout guidance for engineers evaluating the MAX310EWN+. It also distinguishes the explicitly documented drop-in candidate from related multiplexers that use a different package or function and therefore are not direct replacements.

RFQ Contact
MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311CWN+

MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311CWN+ is an 8-channel CMOS RF video multiplexer with a dual 4:1 configuration, 150 ohm on-resistance, and operation across positive and negative supply ranges of +4.5 V to +16.5 V and -16.5 V to -4.5 V. The device is packaged in an 18-pin SOIC for surface-mount PCB integration. An RF video multiplexer is a semiconductor switch used to route multiple high-frequency or video signals through a shared signal path. Within the broader interface-IC hierarchy, the MAX311 belongs to the analog switch and multiplexer family, where CMOS switching elements control signal routing. Its dual 4:1 organization allows several sources to be selected toward downstream receiver, test, or signal-processing circuitry. The MAX311CWN+ supports positive and negative supply rails, making it suitable for systems that require both polarities. Its specified 150 ohm on-resistance provides a defined impedance for routing calculations, while the eight-channel architecture consolidates multiple signal paths into one package. The 18-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB manufacturing processes. According to the Analog Devices MAX311 product page, the MAX311 is in production and is described as an 8-channel CMOS RF video multiplexer. Product documentation identifies the family as MAX311 with a data sheet revision of 0, but engineers should verify the complete pin description, control truth table, switching timing, bandwidth, channel capacitance, and absolute maximum ratings in the manufacturer data sheet before finalizing a design. Typical uses include professional video routing, RF test equipment, video signal selection, broadcast and monitoring systems, and instrumentation that must choose among several RF or video inputs. The dual 4:1 structure can support paired routing or channel-selection functions when the system architecture requires two independent groups of four inputs. The primary design consideration is signal integrity. Keep traces short, use a controlled-reference-ground layout, and account for the 150 ohm on-resistance when driving downstream inputs. Decoupling and protection requirements should follow the manufacturer application guidance because incorrect supply sequencing or signal overvoltage can damage a high-frequency analog switch. This product page combines the manufacturer product identity, exact package and supply information, a confirmed direct replacement, practical routing guidance, and a structured comparison with less suitable interface alternatives. It supports faster component selection while preserving the checks needed for reliable RF and video circuit implementation.

RFQ Contact
MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated
MAX311EPE

MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated

The Maxim Integrated MAX311EPE is an 8-channel CMOS RF/video multiplexer packaged in a 16-pin DIP. The device is designed to route one of eight input signals to a common output, with an on-resistance of up to 250 ohms and switching times of up to 1 microsecond. According to the manufacturer datasheet, the MAX311 family provides off-channel isolation guaranteed at -66 dB at 5 MHz and typical power consumption of 1.1 mW when operated with plus or minus 15 V power supplies. An RF/video multiplexer is a signal-routing semiconductor that selects among multiple analog inputs and connects the selected channel to an output. In the broader hierarchy, it belongs to the switch and multiplexer family, the interface IC category, and ultimately the semiconductor and signal-path component classes. This distinction from a digital multiplexer is important: the MAX311EPE carries analog or RF signals and therefore depends on off-state isolation, on-state resistance, bandwidth, and switching speed rather than digital logic levels. Key features include eight multiplexed channels, CMOS construction, a maximum on-resistance of 250 ohms, and maximum on and off times of 1 microsecond. The high-frequency isolation characteristic helps prevent an unselected input from coupling energy into the selected output. With positive and negative 15 V supplies, the supported input signal range extends from +12 V to -15 V, allowing bipolar analog signals to be routed while the device remains in the analog signal path. Technically, the MAX311EPE uses complementary CMOS switching structures to control the analog channels. When one address is asserted, the corresponding input is connected to the output; the address decoder and enable logic determine which channel conducts. The -66 dB off-isolation guarantee at 5 MHz is especially relevant when adjacent sources carry high-frequency video or RF content, because it limits crosstalk between the active and inactive inputs. The 250-ohm maximum on resistance must also be included in gain-loss and impedance calculations for downstream receivers. Typical applications include video test equipment, RF signal-routing systems, instrumentation, broadcast and professional video interfaces, and analog measurement setups where several signal sources must share a receiver or analyzer. The MAX311EPE is most appropriate where bipolar signal handling and channel isolation matter more than very low on resistance. Systems operating at substantially higher frequencies or requiring lower insertion loss should verify bandwidth and impedance behavior against the complete circuit rather than relying only on the isolation rating. A key design consideration is the interaction between switching transients, grounding, and downstream input capacitance. Keep the selected signal path short, maintain a low-impedance return connection, and use the manufacturer pin-description table when assigning address and control traces. Verify the positive and negative supply sequencing requirements, bypass each supply rail close to the device, and account for the 1-microsecond maximum transition time when the muxed receiver cannot tolerate channel-switch transients. This page combines the available manufacturer-level electrical characteristics, packaging information, sourcing guidance, and application engineering notes into a design-oriented overview. It also highlights where a replacement must be checked against the original 16-pin DIP footprint, pin functions, supply arrangement, signal range, isolation, on-resistance, and switching timing rather than being selected from channel count alone.

RFQ Contact
MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311EWN+

MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311EWN+ is an 8-channel, CMOS RF video multiplexer designed for routing high-frequency video signals in electronic systems. The device is offered in an 18-pin wide SOIC package for surface-mount assembly, with production documentation identified on the manufacturer product page. Its multiplexed switching architecture makes it applicable to video test equipment, imaging systems, broadcast equipment, and other RF or video signal-routing designs where one of several channels must be selected by control logic. A video multiplexer is a semiconductor switching device that connects multiple signal inputs to a common output path. In the product hierarchy, the MAX311EWN+ is an analog switch and multiplexer IC, which is a type of interface IC used to route high-speed signals under digital control. The MAX311 family is identified by Analog Devices as an 8-channel CMOS RF/video multiplexer. The wide SOIC package provides a practical option for conventional PCB assembly and offers enough mechanical spacing for production inspection compared with a fine-pitch package. The MAX311EWN+ uses CMOS switching circuitry to control RF or video signal paths. CMOS implementation is suited to high-input-impedance systems because it can provide low loading on the source signals while accepting digital control inputs from a controller. The multiplexing function can reduce the number of separate downstream receivers, comparators, or signal-processing channels required when several sources must be routed through a common processing chain. Primary applications include video measurement systems, multimedia routing, broadcast and professional video equipment, camera and imaging test setups, RF test fixtures, and compact embedded video systems. The 8-channel configuration allows a controller to scan or select among multiple sources, making the device useful in automatic test equipment where repetitive routing is required. Designers should also evaluate signal attenuation, isolation, switching speed, bandwidth, control levels, and channel count against the specific source impedance and termination network. For PCB implementation, place the device close to the routed signals and provide a continuous ground reference around the package. Keep high-frequency video traces short and use controlled-impedance routing when trace geometry or dielectric properties affect signal quality. Decoupling near the supply pins should follow the capacitor-selection and placement guidance in the manufacturer data sheet. The control traces should be kept away from sensitive analog paths to minimize switching transients and unintended coupling. This page organizes the manufacturer identification, exact orderable MPN, package information, functional requirements, application guidance, comparison parameters, and engineering considerations into a practical procurement and design reference. It also distinguishes the verified drop-in replacement from package or channel-count mismatches, helping engineers avoid substitutions that appear similar but would require PCB changes or redesign.

RFQ Contact
MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices
MAX312EUE+

MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices

Analog Devices MAX312EUE+ is a four-circuit CMOS analog switch with a 1:1 SPST topology, 10Ω maximum on-resistance, and a 16-pin TSSOP package. The device provides four independently controlled switches that conduct equally well in either signal direction, making it suitable for routing analog, digital, and low-voltage instrumentation signals. An analog switch is an integrated semiconductor device that connects or disconnects a signal path under digital control. The MAX312EUE+ belongs to the analog switch and multiplexer hierarchy within interface ICs, providing a defined on-state resistance, off-state leakage, and logic-controlled switching behavior. Its four-channel structure consolidates multiple point-to-point routing functions into one package. Key features include a maximum on-resistance of 10Ω and on-resistance matching of 1.5Ω between channels. Matching is important when several switched paths influence one measurement or signal chain because it helps minimize channel-dependent gain errors. The MAX312 also offers low leakage of 2.5nA at +85°C and equal conduction in both directions, allowing flexible signal-routing topology. The four SPST switches use CMOS control inputs, enabling each channel to be placed in a defined connection state independently. Four independent switches can support signal isolation, test-point selection, instrumentation routing, or the connection of external circuit sections to a shared analog node. The 16-pin TSSOP package supports surface-mount PCB assembly while keeping the circuit compact. Typical uses include data-acquisition systems, sensor signal conditioning, automated test equipment, sample-and-hold interfaces, battery-powered instrumentation, and general-purpose analog signal routing. Because the switches support bidirectional conduction, the same device can route either a source signal toward a load or connect a measurement chain back toward its source. PCB design should place the device near the signals it switches and route high-impedance sensor nodes to minimize parasitic capacitance and leakage. Control traces should remain away from sensitive analog inputs, and unused control inputs should be held at defined logic levels. Verify signal amplitude, bandwidth, temperature, and switch current against the manufacturer datasheet before finalizing the routing design. This product page combines the manufacturer’s switch specifications with practical PCB guidance, package details, selection criteria, and same-family drop-in alternatives. The comparison and design notes explain how on-resistance matching, leakage, logic control, and package reuse affect engineering decisions when replacing an existing four-channel analog switch.

RFQ Contact
MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI
MAX313CUE+

MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI

Analog Devices MAX313CUE+ is a quad SPST CMOS analog switch with four independently controlled normally open channels, a maximum on-resistance of 10 ohms, and a 16-pin TSSOP package. It supports single-supply operation from 4.5 V to 30 V and dual-supply operation from -4.5 V to -20 V and +4.5 V to +20 V. Typical on-resistance is 6.5 ohms, while guaranteed channel matching is 1.5 ohms maximum. A CMOS analog switch is a voltage-controlled semiconductor device that routes analog or digital signals between circuit nodes. The MAX313 belongs to the analog switch and multiplexer hierarchy, where an analog switch performs point-to-point routing and a multiplexer connects multiple signals to a common channel. Its SPST configuration provides one normally open path per switch, making it suitable for isolation, signal selection, test-fixture routing, and bidirectional analog-signal control. The four channels can conduct equally well in either direction. The MAX313CUE+ combines low on-resistance with channel-to-channel matching of 1.5 ohms maximum and on-resistance flatness of 2 ohms maximum over the specified signal range. These characteristics help minimize gain error and distortion when several switched channels must present similar resistance to downstream circuitry. It also provides low leakage and low power consumption for precision and power-sensitive systems. The MAX313 family operates from a wide supply range and supports rail-to-rail signal handling. According to the Analog Devices MAX313 product page, the devices are pin compatible with the DG411, DG412, and DG413 families. The manufacturer also specifies guaranteed ESD protection greater than 2000 V per Method 3015.7 and crosstalk above 96 dB at 20 kHz, helping protect sensitive analog paths and limit interaction between adjacent channels. Typical uses include precision test and measurement systems, analog signal-conditioning modules, battery-powered instrumentation, industrial control interfaces, and signal-isolation networks. The device can route sensor outputs, test signals, or external inputs without introducing the continuous power loss associated with a permanently conducting analog path. It is particularly useful when signal integrity, repeatable channel resistance, and low off-state leakage are more important than maximum switching speed. When laying out a MAX313CUE+ board, follow the TSSOP-16 pin-assignment table in the manufacturer datasheet and keep high-impedance routes short to minimize leakage pickup. Place supply decoupling close to the device, and evaluate switching transients when the source impedance is high. The normally open architecture requires the correct drive polarity at each control input; consult the control-input truth table before changing logic levels. This product record combines the manufacturer specifications, package information, replacement references, and practical design guidance into one engineering-focused view. It also identifies same-package alternatives and explains when their electrical or environmental differences matter, helping designers select the correct switch without introducing a footprint change.

RFQ Contact
MAX314CPE+ - Quad SPST Analog Switch | Analog Devices
MAX314CPE+

MAX314CPE+ - Quad SPST Analog Switch | Analog Devices

The Analog Devices MAX314CPE+ is a four-circuit CMOS analog switch with four independently controlled SPST channels, a maximum on-resistance of 10 ohms, and a 16-pin PDIP package. Each switch conducts equally well in either direction, making the device suitable for routing analog, digital, and low-frequency instrumentation signals. An analog switch is a solid-state semiconductor device that connects or isolates circuit paths under electrical control. Unlike a mechanical relay, it operates without moving contacts, enabling fast switching and compact integration. The MAX314CPE+ belongs to the CMOS analog-switch hierarchy and provides four SPST channels in a through-hole package for applications that require signal routing rather than continuous power conversion. The device has a maximum on-resistance of 10 ohms and on-resistance matching between channels of 1.5 ohms. Its low leakage of 2.5 nA at +85°C helps preserve signal integrity in high-impedance circuits. Bidirectional conduction expands routing flexibility, while low power consumption supports both portable and fixed equipment. ESD tolerance greater than 2000 V per Method 3015.7 adds handling protection during assembly. Each of the four switch channels provides a separate control path, allowing a system to isolate a sensor, select a measurement route, or disconnect an external interface. The parallel CMOS structure avoids mechanical contact delay or wear, while the specified resistance matching helps limit channel-dependent gain and attenuation errors when multiple inputs are routed through the device. Typical uses include analog signal multiplexing in test and measurement equipment, channel isolation in data-acquisition systems, switching between sensors and amplifiers, and routing control signals in industrial control boards. The 16-pin PDIP package is particularly useful for prototypes, through-hole assemblies, and designs where a socketed or manually solderable package simplifies maintenance. When laying out the circuit, place each switched node close to its source and destination where practical, and avoid sharing long copper paths between sensitive channels. Confirm signal amplitude, leakage requirements, control logic levels, and switching transients against the manufacturer data sheet. The MAX314CPE+ is especially appropriate when four separately controlled, bidirectional, normally open analog paths are needed in a conventional through-hole design. This product page combines the manufacturer specifications, sourcing details, pin-package information, and practical selection guidance. It also identifies same-family alternatives while distinguishing verified drop-in choices from options that require a footprint or interface review before substitution.

RFQ Contact
MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices
MAX3160EAP+

MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices

The Analog Devices MAX3160EAP+ is a 3.0V to 5.5V RS-232/RS-485/RS-422 multiprotocol transceiver with a 20-pin SSOP package. It is programmable as a two-transmitter, two-receiver RS-232 interface or as a single RS-485/RS-422 transceiver, allowing one physical interface circuit to support multiple serial protocols. The device also supports pin-selectable transmitter slew rates for RS-232 and RS-485/422 operation, helping reduce EMI and cable reflections. Analog Devices identifies the MAX3160 family as a low-power multiprotocol interface solution, with a listed 1 uA operating-current feature and data rates up to 250 kbps for suitable operation. The MAX3160EAP+ is packaged as a 20-SSOP surface-mount device. Its protocol configurability makes it useful in industrial controls, interface converters, networking peripherals, point-of-sale equipment, and security systems where a board must accommodate legacy RS-232 alongside balanced RS-485 or RS-422 links. The MAX3160 family is pin-programmable, so the same PCB can be configured differently during assembly or test. Compared with a fixed RS-232 transceiver, the MAX3160EAP+ adds RS-485/RS-422 capability and selectable slew-rate control in one interface IC. Its low operating-current positioning is important for portable and space-constrained equipment, while the SSOP footprint simplifies integration with conventional surface-mount assembly. Design decisions should confirm the selected protocol, termination requirements, cable length, data rate, and logic-level compatibility against the manufacturer datasheet.

RFQ Contact
MAX31856MUD+ Precision Thermocouple Converter | Analog Devices
MAX31856MUD+

MAX31856MUD+ Precision Thermocouple Converter | Analog Devices

The Analog Devices MAX31856MUD+ is a precision thermocouple-to-digital converter with cold-junction compensation, digital linearization, Celsius-formatted output, and a 14-TSSOP package. The verified source data identifies 0.0078125°C resolution and supports readings from -55°C to 125°C for the listed device context, with thermocouple measurements reaching as high as +1800°C. It converts thermocouple signals into digital temperature data while supporting multiple thermocouple types through device configuration. A thermocouple-to-digital converter is an interface IC that conditions a low-voltage thermoelectric voltage, performs cold-junction compensation, applies the appropriate linearization for the selected thermocouple type, and transfers temperature data to a host controller. The MAX31856 belongs to the sensor and detector interface category and sits between physical temperature sensors and digital embedded systems. Its digital interface makes temperature monitoring suitable for industrial equipment, test systems, control loops, and embedded instrumentation. The verified manufacturer result identifies cold-junction compensation, thermocouple signal digitisation, linearization, Celsius output format, and 0.0078125°C resolution as central features. The device is supplied in a 14-pin TSSOP package, with the MUD+ ordering code shown by DigiKey as a thermocouple-to-digital converter IC. The source material does not provide a complete verified set of electrical limits, SPI timing values, thermocouple input ranges for every type, or package dimensions, so those values are not inferred here. Because a thermocouple measures the temperature difference between a sensing junction and a reference junction, cold-junction compensation is essential for accurate measurements near ambient temperature. The MAX31856 handles this function internally, allowing the host system to receive compensated digital temperature data rather than raw thermocouple voltage. Digital linearization further reduces the software burden associated with converting nonlinear thermocouple voltage into temperature. Typical uses include industrial furnace monitoring, temperature-controlled processes, laboratory equipment, environmental monitoring, and embedded thermal control. In each case, the thermocouple type, wiring, cold-junction implementation, grounding strategy, and digital interface configuration must be selected according to the manufacturer's datasheet. The verified data does not identify a specific companion MCU or application reference design, so companion products are not asserted as manufacturer-recommended parts. The principal design consideration is ensuring that the selected thermocouple, input filtering, grounding, and digital interface match the system measurement range. For thermocouple signals, keeping the analog input path away from switching nodes and noisy digital return currents helps preserve measurement integrity. This page consolidates verified distributor listings, the official Analog Devices product page, and the available cross-reference information without inventing missing electrical parameters.

RFQ Contact
MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices
MAX318CPA+

MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices

The Analog Devices MAX318CPA+ is a precision, normally open, single-pole single-throw CMOS analog switch with an on-resistance of 35 ohms, housed in an 8-pin PDIP package. It routes one analog signal using a 1:1 SPST topology and is designed for precision signal-selection and test systems. An analog switch is a semiconductor interface device that connects or disconnects an analog signal path under digital control. The MAX318CPA+ belongs to the analog switch hierarchy within interface ICs and multiplexers, providing a simpler alternative to a multi-channel multiplexer when only one signal path must be selected. Its normally open configuration keeps the switched node disconnected until the control input activates the path. Key characteristics include a maximum on-resistance of 35 ohms, operation from 4.5 V to 20 V, and normally open SPST behavior. The device is specified as a precision CMOS analog switch with low on-resistance that remains substantially flat across the analog signal range. According to the Analog Devices MAX318 product page, on-resistance is guaranteed below 35 ohms and is matched within 2 ohms between channels in the associated precision-switch family. The MAX318CPA+ is intended for precision instrumentation, signal routing, test and measurement equipment, industrial control interfaces, and data acquisition systems. Its single-channel architecture simplifies control logic while preserving the low resistance required to transfer low-level or precision analog signals. The 8-pin PDIP package also supports conventional through-hole assembly and prototype boards where fine-pitch surface-mount routing would be inconvenient. Designers should verify the control logic, supply voltage, allowable signal voltage, and switching transients against the manufacturer data sheet before use. Because an analog switch can introduce small resistance variation, channel resistance matching, charge injection, off leakage, and bandwidth determine whether it is suitable for a particular signal path. Input and output protection may also be required when external voltages exceed the device ratings. This page combines the manufacturer specifications, verified sourcing links, application guidance, comparison information, and practical design notes to support component selection and PCB implementation. The MAX318CPA+ is best suited to designers who need a simple, normally open, precision SPST switch rather than a multi-channel multiplexer.

RFQ Contact
MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices
MAX319CSA+

MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices

The Analog Devices MAX319CSA+ is a precision, single-pole double-throw CMOS analog switch with one normally open and one normally closed path, a maximum on-resistance of 35Ω, and an 8-pin SOIC package. It is designed for precision signal routing where low on-resistance, low charge injection, low power consumption, and high electrostatic-discharge withstand are important. An analog switch is a semiconductor interface that routes an analog signal between circuit nodes under digital control. Unlike a relay, it operates electronically at low voltage and can switch signals rapidly without mechanical wear. The MAX319 belongs to the broader analog-switch hierarchy, which sits alongside multiplexers, demultiplexers, and interface ICs used to connect sensors, test equipment, measurement systems, and signal-processing electronics. Key electrical characteristics include on-resistance below 20Ω typical and 35Ω maximum, guaranteed channel matching within 2Ω, and on-resistance variation of no more than 3Ω maximum across the analog signal range. Charge injection is low at 10pC, while power consumption is 35µW. These characteristics help preserve signal fidelity when the switch is used in measurement, control, or data-acquisition paths. The MAX319 family uses an improved silicon-gate CMOS process and rail-to-rail analog signal handling capability associated with a 44V maximum breakdown voltage. Its precision configuration is useful when signal-source impedance, leakage, or switch resistance could otherwise influence the measurement result. The MAX319CSA+ ordering code identifies the 8-pin SOIC package and the manufacturer's standard production configuration. Typical uses include battery-powered instrumentation, automated test equipment, analog measurement systems, signal-path routing, sample-and-hold circuits, and industrial control interfaces. Its low 35µW power consumption is particularly useful in portable equipment, while the 35Ω maximum on-resistance is suitable for moderate-impedance analog signals rather than ultra-low-impedance precision dividers. When designing a circuit around the MAX319CSA+, account for the switch's on-resistance, leakage, charge injection, and off-state behavior when calculating signal attenuation and timing. Place the device close to sensitive signal paths, maintain adequate grounding, and use the manufacturer pin-description table when assigning PCB tracks. Verify the logic levels and control polarity against the actual device documentation before finalizing the layout. This product page combines the manufacturer's device specifications with practical design guidance, package information, sourcing details, and a conservative drop-in assessment. It emphasizes verified distinctions between electrically similar devices so engineers can determine whether a replacement preserves both the board footprint and the required switch behavior.

RFQ Contact
MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices
MAX3221CAE+

MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CAE+ is a one-driver, one-receiver RS-232 transceiver designed for +3V to +5.5V operation and supplied in a 16-pin SSOP package. It provides 1 µA supply current when AutoShutdown is active, while integrating the charge-pump circuitry required to generate RS-232-compatible driver levels from a low-voltage supply. The MAX3221CAE+ is suitable for portable equipment, industrial controls, data acquisition systems, and other equipment that requires a compact, low-power serial interface. An RS-232 transceiver is an interface IC that combines a transmitter and receiver for communicating between a logic-level device and an RS-232 port. The transmitter converts low-voltage TTL or CMOS signals into RS-232 levels, while the receiver converts incoming RS-232 signals back into logic-compatible levels. The MAX3221 family belongs to the interface IC hierarchy and provides a practical way to bridge modern embedded systems with legacy RS-232 equipment. The MAX3221CAE+ includes Maxim's AutoShutdown feature, allowing the on-board power supply and driver circuitry to shut down when the receiver does not detect a valid signal. According to the Analog Devices MAX3221 product page, the device operates from +3V to +5.5V and reaches a supply current of 1 µA. These characteristics are particularly valuable in battery-powered instruments where a permanently active RS-232 interface would increase standby power consumption. The MAX3221 is a 1-driver/1-receiver 16-pin SSOP version of the 2-driver/2-receiver MAX3223. Its integrated RS-232 supply uses charge-pump circuitry to develop the voltage swing needed by the transmitter. The C designation denotes the family's capacitor configuration, while the E designation provides shutdown-control functionality. The A suffix identifies the package and temperature-related ordering configuration used in the MAX3221CAE+ ordering code. Typical applications include battery-powered test equipment, handheld configuration tools, serial adapters, industrial instrumentation, point-of-sale equipment, and embedded systems that must communicate with a host computer through an RS-232 port. The 16-pin SSOP footprint is useful for compact designs, although engineers should verify connector protection, cable length, logic levels, and supply compatibility against the system requirements. The principal design consideration is signal integrity. RS-232 is a single-ended, unbalanced interface, so cable routing and ground quality can materially affect noise immunity. Place the transceiver close to the interface connector, provide a low-impedance ground path, use suitable protection for exposed cables, and observe the manufacturer's recommended charge-pump capacitor values. External circuitry may also be required for hardware handshaking or for conditioning signals on long or electrically noisy cables. This page organizes the MAX3221CAE+ specifications, application guidance, package information, and verified same-package alternatives into an engineering-focused reference. It also highlights the practical trade-offs among shutdown, supply-voltage, capacitance, and temperature variants so designers can make a replacement decision based on actual circuit requirements rather than package similarity alone.

RFQ Contact
MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+T

MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+T is a one-driver, one-receiver RS-232 transceiver with AutoShutdown, operating from a 3 V to 5.5 V supply and drawing 1 µA when the charge-pump circuit is inactive. The device is packaged in a 16-pin SSOP and is designed for compact, low-power serial-interface equipment. Its principal characteristics are one RS-232 driver, one RS-232 receiver, 3 V to 5.5 V operation, and automatic supply shutdown when no valid receiver signal is detected. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class of interface ICs, which sits between computer serial ports or control equipment and external communication links. The MAX3221 is the one-driver, one-receiver member of the MAX3221 family and is smaller than two-channel RS-232 transceivers such as the MAX3223. AutoShutdown is the device's principal power-management feature. When the receiver does not detect a valid signal level, the onboard power supply and driver shut down, reducing supply current to 1 µA as stated on the manufacturer product page. This behavior is valuable in battery-powered or intermittently connected equipment because a permanently connected serial port no longer needs to retain a full charge-pump load when communication is inactive. The 3 V to 5.5 V supply range supports integration with both 3.3 V and 5 V system rails. The MAX3221 integrates the RS-232 line driver, receiver, and onboard charge-pump circuitry in one compact package. This integration eliminates a separate external power-supply circuit while providing the voltage conversion required by the RS-232 interface. Unlike designs requiring a ±12 V supply, the MAX3221 generates RS-232-compatible levels from a single low-voltage supply. Its 16-SSOP construction supports conventional surface-mount assembly while conserving board area in embedded control, industrial, and communications systems. Typical applications include single-port serial-control links in industrial equipment, point-of-sale terminals, data-acquisition systems, instrumentation, and battery-operated peripherals. In each case, the device handles one unidirectional data path with the driver and the opposite direction with the receiver. Because it provides only one driver and one receiver, a design needing two physical RS-232 channels should evaluate a two-channel transceiver rather than adding a second MAX3221 unnecessarily. The primary design consideration is external bypass capacitance. Place the supply bypass capacitor and charge-pump capacitor close to their associated pins, with short ground paths to reduce supply disturbance and improve interface stability. Confirm the external capacitor values and connection details in the manufacturer datasheet before layout release, especially in designs operating from 3.3 V where charge-pump headroom and startup behavior affect system margins. This page combines the manufacturer product information with practical interface guidance, structured specifications, verified pin-compatible family alternatives, and design considerations that help engineers evaluate the MAX3221CAE+T for low-power RS-232 implementations.

RFQ Contact
MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+TG1Z

MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+TG1Z is a single-driver, single-receiver RS-232 line transceiver designed for true +3V to +5.5V operation. It provides one driver and one receiver in a 16-pin SSOP package, supports the full RS-232 interface standard, and draws only 1 µA through the AutoShutdown feature when no valid receiver signal is detected. The commercial-temperature, tape-and-reel ordering designation is MAX3221CAE+TG1Z. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic. The MAX3221 belongs to the hierarchy of RS-232 interface transceiver, serial interface IC, interface controller, and semiconductor. It is intended for equipment that needs bidirectional or unidirectional point-to-point serial connectivity without relying on a modern multi-standard transceiver family. The principal features of the MAX3221 include one RS-232 driver, one RS-232 receiver, operation from 3V to 5.5V, and a 1 µA AutoShutdown supply current. AutoShutdown reduces supply demand when the receiver does not detect a valid signal level. This makes the device useful in portable equipment and systems where a permanently connected serial port would otherwise waste power. Its 16-terminal gull-wing SSOP construction supports compact surface-mount assemblies. The device uses Maxim's low-power RS-232 interface architecture to support systems that cannot tolerate excessive supply current. The on-board charge-pump and driver circuitry provide the voltage swings required by RS-232 while the receiver converts the line-level input into a digital output. Designers should still account for the voltage difference between logic-side ground and the RS-232 line reference when integrating the device with another circuit board. Typical uses include industrial serial adapters, test equipment, data acquisition modules, point-of-sale terminals, instrument-control links, and legacy peripheral interfaces. The MAX3221 is especially appropriate where a compact single-channel interface is required rather than the multiple drivers and receivers offered by larger RS-232 families. For battery-powered instruments, its 1 µA shutdown current can reduce standby consumption. A key design consideration is ensuring that the logic supply, charge-pump capacitors, driver connection, receiver input, and signal ground are routed according to the manufacturer application guidance. Keep the interface connector and transceiver return path together where practical, and use suitable protection for exposed cables. Review the manufacturer's pin description and application circuit before assigning the 16 SSOP terminals or selecting external bypass capacitors. This product record combines the official MAX3221 family information, exact package attributes, commercial sourcing information, pin-compatible alternatives, comparison parameters, and application guidance to support component selection and board-level implementation.

RFQ Contact
MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDB

MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDB is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDB alongside other single-channel RS-232 transceivers.

RFQ Contact
MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3221CDBR

MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX3221CDBR is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDBR alongside other single-channel RS-232 transceivers.

RFQ Contact
MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDBRG4

MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDBRG4 is a single-channel RS-232 line driver and receiver with a 3 V to 5.5 V supply, 250 kbit/s operation, and ±15 kV ESD protection, housed in a 16-pin SSOP package. The transceiver integrates one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit for generating the bipolar voltage levels required by RS-232. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a RS-232 link. Within the signal-chain hierarchy, it belongs to the RS-232 interface, line-driver and receiver, communications-interface, and semiconductor categories. The MAX3221CDBRG4 is intended for equipment that needs one bidirectional serial port while operating from a 3 V to 5.5 V system supply. Key features include a maximum data rate of 250 kbit/s, ±15 kV ESD protection on the serial-port connection pins, and a low shutdown supply current. According to the manufacturer datasheet, the device provides AutoShutdown operation and supports true +3 V to +5.5 V supplies. Its integrated charge pumps reduce the external component count compared with a discrete RS-232 interface implementation. The MAX3221 family combines a driver and receiver with internal level-shifting circuitry. The charge-pump section develops positive and negative voltage rails from the single device supply, allowing the line interface to produce RS-232-compatible output levels. The receiver converts the bipolar serial signal back to a logic-compatible signal, while the dedicated receiver-enable control can place the receiving path in a reduced-power state when it is not required. Typical uses include industrial serial-port adapters, point-to-sale equipment, test and measurement instruments, embedded control systems, and legacy peripheral connections. The single-channel arrangement is especially suitable for compact systems that need one RS-232 port but no multi-port RS-232 expansion. When designing around the MAX3221CDBRG4, preserve the charge-pump capacitor and bypass-capacitor placement recommended in the manufacturer datasheet. Confirm that the host interface uses the correct logic voltage and that the receiver-enable polarity matches the controller firmware. The 16-pin SSOP footprint also requires careful solder-joint inspection because lead pitch and package density can complicate rework. This product page consolidates the electrical limits, interface function, packaging information, and practical design considerations for the MAX3221CDBRG4. It also identifies verified drop-in alternatives and organizes the selection trade-offs by speed, supply range, temperature grade, and interface configuration.

RFQ Contact
MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI
MAX3221CPW

MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI

Texas Instruments MAX3221CPW is a single-channel RS-232 line driver/receiver with a 3 V to 5.5 V supply, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. The device is packaged in a 16-pin TSSOP package and includes one line driver, one line receiver with a dedicated enable pin, and a dual charge-pump circuit. It is designed to provide the electrical interface between an asynchronous communication controller and a serial-port connector while operating from a single supply voltage. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts received RS-232 signals back into logic-level signals. The MAX3221 belongs to the RS-232 interface IC hierarchy, which includes line drivers, line receivers, and charge-pump-assisted transceivers used for serial communications equipment, industrial controls, instrumentation, and point-of-sale terminals. The dual charge-pump circuit generates the positive and negative voltage levels required by the RS-232 interface without requiring a separate negative supply. The MAX3221 operates from 3 V to 5.5 V, accepts 5 V logic input with a 3.3 V supply, and supports data rates to 250 kbit/s. Its low standby current of 1 µA typical and use of external 0.1 µF capacitors help support compact, power-conscious interface designs. The dedicated receiver enable pin allows the receiver to be disabled when the host does not need to monitor the serial link. The device meets TIA/EIA-232-F requirements and is also associated with ITU V.28 operation, providing a standard RS-232 electrical interface for asynchronous communication systems. The ±15 kV ESD protection is specified pin to pin, including the serial-port connection pins and ground. This protection helps improve system robustness when cables are exposed to electrostatic discharge during installation, servicing, or normal handling. Typical uses include single-channel serial console links, industrial serial adapters, programmable instrument interfaces, barcode and point-of-sale equipment, and embedded systems that require one bidirectional RS-232 channel. The 250 kbit/s capability is appropriate for legacy serial peripherals and control links, while the 3 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. When laying out the circuit, place the charge-pump capacitors and the driver and receiver interface capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog or high-speed digital signals. Confirm that the transceiver enable state matches the host controller’s serial-port requirements before relying on low-power standby operation. This page combines the manufacturer’s RS-232 interface specifications with package and application guidance, verified comparison candidates, and practical design notes for engineers evaluating the MAX3221CPW in compact serial-interface designs.

RFQ Contact
MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments
MAX3221CPWE4

MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWE4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply. The device provides one transmit channel, one receive channel, integrated charge-pump circuitry, and ±15 kV ESD protection in a 16-pin TSSOP package measuring 4.40 mm wide. Its interface operates at the voltage levels required by RS-232 while the low-voltage supply supports modern embedded systems. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level voltages. In the broader semiconductor hierarchy, the MAX3221CPWE4 belongs to the interface IC family and provides the physical signaling layer between a host controller and a serial peripheral. The integrated dual charge pump generates the positive and negative voltage levels required by the RS-232 standard without external discrete capacitors. The principal electrical characteristics visible in the manufacturer documentation include a 3 V to 5.5 V operating supply, single-channel driver and receiver operation, and ±15 kV ESD protection. The single-channel arrangement reduces board area and power consumption compared with multi-channel RS-232 transceivers. The 16-pin TSSOP package is also compatible with surface-mount manufacturing and supports compact serial-interface implementations. The MAX3221CPWE4 uses an RS-232 line driver to convert TTL-compatible transmit data into bipolar line signaling and an RS-232 receiver to recover logic-compatible receive data. A dedicated receiver-enable function provides control over the receive path. Internal dual charge-pump circuitry supports the positive and negative voltage swings associated with RS-232 signaling while operating from a single low-voltage supply. Typical applications include industrial serial-port equipment, data-acquisition systems, service-console interfaces, programmable instrumentation, and embedded control systems that need a compact RS-232 connection. It is particularly suitable when the logic system operates from 3.3 V or 5 V and an RS-232 port must be added without designing a separate high-voltage transmitter circuit. A critical implementation consideration is the distinction between the low-voltage supply and the bipolar voltages generated on the RS-232 side. Decoupling must be placed close to the supply pins, and external charge-pump capacitors must follow the values and layout guidance in the manufacturer datasheet. The PCB should also provide appropriate isolation and return-path planning for the externally accessible serial connector. This product page consolidates the exact-orderable part information, operating limits, package details, replacement guidance, and design-focused guidance that engineers need when evaluating the MAX3221CPWE4. It also provides a structured comparison with same-footprint MAX3221 variants so that temperature-grade, suffix, and sourcing decisions can be made without confusing electrical equivalence with PCB compatibility.

RFQ Contact
MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CPWRE4

MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWRE4 is a single-channel RS-232 line driver and receiver with a dual charge-pump circuit, a 3 V to 5.5 V supply range, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. It is packaged in a 16-pin TSSOP and includes a receiver with a dedicated enable input. The device provides the electrical interface between TTL-compatible logic and an RS-232 port while requiring external charge-pump capacitors of 0.1 µF. An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into the positive and negative voltage swings used by RS-232 equipment. In the broader semiconductor hierarchy, the MAX3221 belongs to the interface IC family, where line drivers and line receivers bridge computer, industrial-control, instrumentation, and communications equipment. Its single-channel architecture is useful when a system needs one bidirectional RS-232 connection rather than the multiple channels found on multi-channel transceiver families. The MAX3221 operates from 3 V to 5.5 V and accepts 5 V logic input when operated from a 3.3 V supply. Its 250 kbit/s data rate supports legacy serial-port, point-to-point control, and embedded equipment links. Pin-to-pin ESD protection of ±15 kV applies to the RS-232 connection pins, including ground, helping protect the interface against electrostatic discharge encountered during installation or handling. Internally, the device combines one line driver, one line receiver with a dedicated enable input, and a dual charge-pump circuit. The charge pumps generate the positive and negative voltages required for compliant RS-232 signaling. The receiver enable function allows a system to place the receive side in a controlled state, while the low standby current supports power-conscious designs where the interface must remain present without continuously receiving data. Typical uses include single-port RS-232 equipment interfaces, industrial controller serial links, programmable-instrument connections, and embedded systems that communicate with legacy peripherals. Because the logic side operates from 3 V to 5.5 V, the device can be used in both 3.3 V and 5 V systems. The 16-pin TSSOP also supports compact board layouts where a larger multi-channel transceiver would be unnecessary. Designers should place the 0.1 µF charge-pump capacitors close to their designated pins and observe the connector-side voltage and polarity requirements of RS-232. The interface does not create isolation, so an exposed or long cable run may require additional surge and ground-management measures. Input and output logic levels must also be checked against the connected controller rather than assumed from the serial-port standard. This page organizes the technical specifications, source links, interface applications, drop-in alternatives, and PCB considerations for engineers evaluating the MAX3221CPWRE4. It also distinguishes exact electrical matches from variants that change package details or feature sets, helping prevent a nominal substitution from creating an unintended PCB or firmware incompatibility.

RFQ Contact