Products (44,000+)

MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices
MAX3221CUE+

MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+ is a production RS-232 transceiver for single-driver, single-receiver communications links. It operates from +3V to +5.5V and is specified for EIA/TIA-232 and V.28/V.24 interfaces. The device includes one line driver, one receiver with a dedicated enable input, and a dual charge-pump circuit that supplies the RS-232 bipolar signal levels required by the communications interface. The MAX3221 family also uses Maxim’s AutoShutdown feature, allowing the on-board supply and drivers to shut down when no valid receiver signal is present, reducing supply consumption in systems where the interface is intermittently active. The MAX3221CUE+ is packaged in a 16-pin TSSOP and is identified by the C suffix and E-grade temperature designation in the manufacturer’s product family documentation. An RS-232 transceiver is an interface IC that translates between single-ended logic-level signals and the voltage-defined, bipolar signaling used by RS-232 equipment. In the transmit direction, the line driver converts logic-level data into an RS-232 signal; in the receive direction, the receiver converts the incoming RS-232 signal into a logic-level output. The dual charge-pump circuit supports the voltage translation required by the RS-232 standard without requiring a separate negative supply. The receiver enable pin gives the system designer a way to control whether the receiver is active, while AutoShutdown provides an additional power-management mechanism for ports that may be idle. The key verified characteristics of the MAX3221CUE+ include its +3V to +5.5V supply range, 1 µA-class shutdown current as described by the manufacturer family documentation, RS-232 transceiver operation, and its 16-pin TSSOP package. The Newark distributor listing identifies the part as an RS-232 transceiver with 120 Kbps signaling and a 70°C operating-temperature listing. The Analog Devices product page identifies the MAX3221 family as production and lists a starting list price of $2.52. Additional operating, electrical, and environmental details are available in the manufacturer datasheet and should be confirmed against the specific ordering code before design release. Typical uses include legacy serial-port equipment, industrial control links, data-acquisition equipment, and embedded systems that require a compact RS-232 port. The MAX3221CUE+ can be used when a design needs a low-voltage digital supply while retaining conventional RS-232 signaling at the connector. Its single-driver and single-receiver organization is appropriate for point-to-point links rather than multi-drop RS-232 networks. The dedicated receiver enable and AutoShutdown functions are useful in systems where the interface must remain available without continuously powering the complete driver and receiver circuitry. The primary design consideration is verifying the exact pinout, capacitor values, and signal-termination requirements from the MAX3221 manufacturer datasheet. Charge-pump capacitors must be placed close to their associated pins, and the RS-232 connector-side circuit should be designed for the voltage and ESD requirements of the application. The MAX3221CUE+ is appropriate when the required interface is one driver and one receiver in a 16-pin TSSOP footprint; designers needing multiple drivers or receivers should select a larger RS-232 transceiver family instead. This page combines manufacturer family information, distributor pricing, verified cross-reference results, application guidance, and design cautions to support practical sourcing and comparison of the MAX3221CUE+ rather than reproducing only the basic distributor description.

RFQ Contact
MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221CUE+T

MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+T is a one-driver, one-receiver RS-232 transceiver designed for operation from a 3.0 V to 5.5 V single supply. The device combines a dual charge-pump supply, automatic shutdown, and a low-dropout line driver in a 16-pin TSSOP package. Its RS-232 line-driver output and receiver input are intended for serial-port connections, while the integrated charge pumps generate the bipolar voltage required to transmit RS-232 signals from a low-voltage supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals into logic-level inputs. In the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class, interface IC category, and broader semiconductor family. It is appropriate where a modern controller operates from 3.0 V or 5.0 V but the attached equipment still uses the voltage range and signaling conventions of the RS-232 standard. The MAX3221 uses AutoShutdown to reduce supply consumption when no valid receiver signal is detected. According to the manufacturer, this feature can reduce onboard supply and driver current to approximately 1 µA when the receiver inputs are inactive. The MAX3221CUE+T ordering code identifies the temperature-range and package configuration, while the +T suffix denotes the tape-and-reel shipping format shown for this part. Internally, the proprietary dual charge-pump circuit produces the elevated voltage used by the driver from one 3.0 V to 5.5 V supply. This architecture avoids a separate negative power rail in equipment using a single positive supply. The receiver converts the RS-232 input into CMOS-compatible logic, and the driver presents the required RS-232 output levels to the connector-side interface. Typical uses include industrial control panels, point-of-sale terminals, serial adapters, embedded instrumentation, and service equipment that must connect a low-voltage processor to an RS-232 port. The 16-pin TSSOP package also suits compact boards where connector spacing and component height are important. The AutoShutdown behavior is particularly useful in battery-powered or intermittently connected portable systems. Layout should place charge-pump capacitors and interface-path components close to the device, keep the RS-232 traces away from sensitive analog and high-speed digital nets, and provide a low-impedance ground return. The external interface must also satisfy the applicable RS-232 voltage, grounding, and ESD requirements. Because this integrated circuit generates only a small number of RS-232 channels, a multiport design may require multiple transceivers or a higher-channel-count device. This product page combines the manufacturer specifications, package information, RS-232 application context, practical layout guidance, and a pin-compatible comparison focused on helping engineers determine whether the MAX3221CUE+T can be used without redesigning an existing 16-pin TSSOP circuit.

RFQ Contact
MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices
MAX3221EAE+

MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices

The Analog Devices MAX3221EAE+ is a 3V-powered, 1-driver/1-receiver RS-232 transceiver with AutoShutdown, operating from 3V to 5.5V and reaching 120 kbps in a 16-pin SSOP package. It provides one transmit driver, one receive path, automatic shutdown and wake-up, and enhanced ESD protection according to the verified manufacturer description. The device is intended for low-voltage serial interfaces where power efficiency, compact footprint, and reliable RS-232 signal translation are required. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 links. The MAX3221 family uses an internal charge-pump circuit to generate the RS-232 transmitter voltage from a single low-voltage supply. In the system hierarchy, it is a communication interface IC, a line-interface device, and a voltage-level translator used between host controllers and external serial equipment. Key verified characteristics include a 3V to 5.5V supply range, 120 kbps data-rate capability, 1 microamp supply-current operation in shutdown, one RS-232 driver, and one receiver. AutoShutdown reduces power use when the receiver does not detect a valid signal. The 16-SSOP package is specified as approximately 5.30 mm wide in the distributor result, making the device suitable for compact equipment designs. The MAX3221EAE+ is appropriate for embedded serial-console connections, industrial control links, point-of-sale systems, instrumentation, and USB-to-RS-232 adapters. The internal charge pump removes the need for a separate bipolar supply, while the receiver and driver provide the basic signal path between a low-voltage controller and an RS-232 connector. The tradeoff is that RS-232 is a single-ended, point-to-point interface with limited cable distance and no multidrop capability. For layout, place charge-pump capacitors and the receiver/transmitter interface components close to their associated pins, and follow the manufacturer's recommended capacitor values. Keep the RS-232 connector-side traces away from sensitive low-level logic where practical. Confirm line rates, cable length, ground continuity, and the system supply level before finalizing the design. This page combines the verified manufacturer description, distributor package information, application guidance, and comparison-oriented design notes to provide practical RS-232 transceiver information beyond a basic catalog listing.

RFQ Contact
MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221EAE+T

MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EAE+T is a 1-driver, 1-receiver RS-232 transceiver with a 3 V to 5.5 V single-supply range, AutoShutdown behavior, and enhanced electrostatic-discharge protection. It is packaged in a 16-pin SSOP and is intended for systems that require a single power rail while exchanging data with an RS-232-compatible equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic levels. The MAX3221 belongs to the broader RS-232 interface, communication interface, and interface IC hierarchy. Its integrated charge-pump supply generates the bipolar voltage required by the RS-232 transmitter, allowing operation from a single low-voltage supply rather than a separate positive and negative power rail. The MAX3221E family features automatic shutdown and wake-up behavior. When no valid signal is detected at the receiver inputs, the on-board power supply and drivers can shut down, reducing supply current to approximately 1 µA according to the manufacturer product information. This behavior is useful in battery-powered and intermittently connected equipment because the interface does not need to remain fully powered between communication sessions. The E version adds enhanced electrostatic-discharge protection. The manufacturer lists ±15 kV ESD protection for the MAX3221E, while the MAX3221 product family is designed for EIA/TIA-232 and V.28/V.24 communications. The MAX3221E product page also identifies IEC 61000-4-2 ESD protection for the RS-232 pins. These ratings should be evaluated against the connector placement and system grounding strategy rather than treated as a substitute for external surge protection. Typical uses include industrial serial-port equipment, point-of-sale terminals, data acquisition equipment, configuration interfaces, and legacy peripheral connectivity. The 16-pin SSOP footprint suits compact designs where space is constrained, although connector routing and exposed-charge-pump behavior still require careful PCB planning. The MAX3221E/MAX3223E/MAX3243E family is available from a 3 V supply, with the exact model selection determined by the required number of drivers and receivers. Designers should follow the manufacturer’s recommended charge-pump capacitor connections, place the four external capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog and high-speed digital paths. Receiver and driver enable functions provide local control, while AutoShutdown can reduce power when the remote device is disconnected. The MAX3221EAE+T is therefore best suited to compact, single-supply RS-232 links that require automatic power saving and improved ESD resilience. This page combines the manufacturer family information with practical interface-selection guidance, package-specific implementation considerations, and qualified comparison options for engineers evaluating replacements for the MAX3221EAE+T.

RFQ Contact
MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EAE+TG1Z

MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221EAE+TG1Z is a single-channel RS-232 transceiver with one driver and one receiver, 3 V to 5.5 V single-power operation, a maximum data rate of 250 kbps, and enhanced ±15 kV IEC ESD protection in a 16-pin SSOP package. The device also provides automatic shutdown and wakeup functions for power-conscious serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level signals between a computer or embedded controller and the voltage levels used by an RS-232 communications link. Within the interface hierarchy, the MAX3221EAE+TG1Z belongs to the RS-232 transceiver class, where it integrates the line driver, line receiver, charge-pump support, and low-power control functions needed to implement a complete single-channel serial port. Key operating characteristics include a 3 V to 5.5 V supply range, 250 kbps maximum signaling rate, and ±15 kV IEC ESD protection. The automatic shutdown and wakeup features help reduce supply consumption when the associated system is inactive. A low-power supply-current specification of 1 µA is associated with the MAX3221EAE family, supporting battery-operated and energy-conscious equipment designs. The MAX3221EAE+TG1Z uses the MAX3221E 1-driver/1-receiver architecture. Its 16-pin SSOP construction keeps the interface compact while providing the external components and connections required for RS-232 operation. The 250 kbps capability makes it suitable for moderate-speed control links, configuration ports, data acquisition equipment, and service interfaces that do not require modern multi-gigabit serial communication. Typical applications include industrial control and instrumentation, data acquisition systems, test and measurement equipment, embedded serial adapters, and point-of-sale or peripheral interfaces. Automatic shutdown is particularly useful in portable and remotely powered systems where the serial transceiver can remain present on the board without maintaining a continuously active internal state. The integrated ESD protection improves interface robustness when cables connect the board to external equipment. A key design consideration is the distinction between the logic-side supply and the RS-232 line-side operating requirements. Confirm capacitor selection, charge-pump operation, logic levels, and shutdown-control polarity against the manufacturer datasheet before layout release. Place the required charge-pump and bypass capacitors close to their designated pins, and keep the RS-232 connector and interface traces physically separated from sensitive analog or high-speed digital nets. This page consolidates the verified electrical identity, package details, interface characteristics, drop-in alternatives, and application guidance for the MAX3221EAE+TG1Z. It also highlights practical distinctions among same-family and cross-brand RS-232 interface options so engineers can select a part based on package fit, supply range, data rate, shutdown behavior, and protection requirements rather than by partial parameter similarity alone.

RFQ Contact
MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECAE+T

MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221ECAE+T is a single-driver, single-receiver RS-232 transceiver operating from 3.0V to 5.5V at up to 250kbps in a 16-pin SSOP package. It integrates a charge-pump voltage converter, automatic shutdown and wake-up, and ±15kV ESD protection for compact, low-power serial-interface designs. An RS-232 transceiver is a semiconductor interface that converts logic-level TTL or CMOS signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. Positioned within the interface IC and power-management hierarchy, the MAX3221 supports point-to-point serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment. The MAX3221 uses one transmitter and one receiver, making it suitable for serial links requiring a single bidirectional channel. Its 3.0V to 5.5V supply range permits operation from both 3.3V and 5V systems. AutoShutdown reduces supply current to approximately 1µA when the receiver detects no valid signal, helping conserve power in intermittently connected equipment. The integrated charge-pump circuitry develops the positive and negative voltages required by RS-232 without a separate power supply. Enhanced electrostatic-discharge protection is rated at ±15kV, an important consideration for exposed cables and connectors. The interface also operates at up to 250kbps, covering conventional asynchronous RS-232 communication rates while providing margin for modern firmware-based protocols. Typical uses include RS-232 configuration ports on industrial controllers, test and measurement equipment, POS terminals, serial adapters, and embedded systems communicating with legacy peripherals. Because RS-232 is a single-ended, unbalanced standard, cable routing and grounding remain important, and long cables should be treated as potential sources of noise and ESD events. Place the charge-pump capacitors and transceiver-side bypass capacitor close to their associated pins. Keep the RS-232 connector interface path physically separate from sensitive logic, and route the ground return appropriately for the installed cable. Verify baud-rate, logic-level, and supply compatibility before replacing another transceiver. This page combines the manufacturer's RS-232 interface specifications, package information, sourcing guidance, and practical implementation considerations. It also organizes pin-compatible alternatives and explains where their ESD, power-management, and temperature-grade differences matter during component selection.

RFQ Contact
MAX3221ECDBR - 3V-5.5V 250kbps RS-232 | Texas Instruments
MAX3221ECDBR

MAX3221ECDBR - 3V-5.5V 250kbps RS-232 | Texas Instruments

The Texas Instruments MAX3221ECDBR is a 3V to 5.5V single-channel RS-232 line driver/receiver with 250kbps data-rate capability, ±15kV IEC ESD protection, and a 16-pin SSOP package. It provides the electrical interface between an asynchronous communications controller and an RS-232 port while operating from a 3V to 5.5V supply. An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232-compatible line levels and converts incoming RS-232 signals back into logic levels. It belongs to the RS-232 interface transceiver category, connects digital controllers to serial ports, and belongs to the broader interface IC and semiconductor hierarchy. The MAX3221ECDBR integrates one driver and one receiver for a single RS-232 channel. Its principal operating characteristics include a 3V to 5.5V supply range, a maximum data rate of 250kbps, and ±15kV IEC ESD protection. The device is specified for a 0°C to 70°C operating-temperature range and is offered in a compact 16-pin SSOP package measuring approximately 0.209 inches, or 5.30mm, wide. These characteristics make it suitable for equipment that must generate or receive RS-232 signals from a low-voltage digital system. The MAX3221ECDBR is identified as a full RS-232 single-channel transceiver and is designed around the A/EIA-232-F interface requirements described by the manufacturer. Its integrated driver, receiver, charge-pump support components, and protection features reduce the external circuitry required around a conventional asynchronous serial controller. The 3V minimum supply operation permits use with modern 3.3V system logic without requiring a 5V-only interface rail. Typical uses include single-port RS-232 adapters, industrial serial controllers, point-of-sale equipment, test instruments, data-acquisition systems, and embedded equipment that still uses an RS-232 physical interface. In these systems, the IC receives logic-level serial data for transmission and converts a remote RS-232 signal into a logic-level receive signal. The 250kbps capability supports substantially faster asynchronous links than legacy low-speed serial ports. PCB design should preserve the pin assignments and decoupling recommendations in the manufacturer datasheet. Keep the charge-pump capacitor connections, driver and receiver traces, and exposed circuit paths compact, and provide suitable protection at an accessible connector because the internal ±15kV IEC ESD rating does not remove the need for an appropriate system-level surge and ESD strategy. This page combines the verified device identity, package information, operating limits, interface characteristics, replacement candidates, and application-specific design guidance to support component selection and PCB implementation without treating the manufacturer datasheet as a substitute for careful signal-integrity and protection review.

RFQ Contact
MAX3221ECDBRG4 - 3V-5.5V Single RS-232 Transceiver | TI
MAX3221ECDBRG4

MAX3221ECDBRG4 - 3V-5.5V Single RS-232 Transceiver | TI

The Texas Instruments MAX3221ECDBRG4 is a 3 V to 5.5 V single-channel RS-232 line driver and receiver with ±15 kV IEC 61000-4-2 ESD protection, housed in a 16-SSOP package measuring 5.30 mm wide. The device combines one driver and one receiver in a compact interface suitable for bidirectional serial-port connections. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible voltage levels and restores incoming RS-232 signals to logic-compatible levels. It belongs to the interface IC hierarchy, where it connects digital logic or microcontrollers to legacy peripheral ports. The MAX3221E family also uses on-chip charge-pump circuitry to generate the bipolar voltage levels required by RS-232 without a separate negative supply. Key features include operation from 3 V to 5.5 V, one driver and one receiver, ±15 kV human-body-model ESD protection, ±8 kV IEC 61000-4-2 contact discharge protection, and ±15 kV air-gap discharge protection. The device uses four external 0.1 µF charge-pump capacitors. Its 16-SSOP surface-mount package supports compact industrial-control, instrumentation, and embedded equipment layouts. The MAX3221E architecture provides the electrical interface required by asynchronous serial systems. A single external capacitor at each charge-pump node supports the internal voltage conversion, while the driver presents the bipolar voltage levels expected by an RS-232 port and the receiver converts those levels back to digital logic. This integration simplifies PCB area compared with discrete level-shifting and charge-pump networks. Typical applications include debug-console connections, industrial serial adapters, point-of-sale equipment, test and measurement instruments, and embedded systems that retain an RS-232 port. For new designs, an RS-232 transceiver is most useful when an existing host or peripheral expects the physical RS-232 interface rather than USB, RS-485, or a proprietary differential link. Place the four 0.1 µF charge-pump capacitors close to their designated pins and route the driver output and receiver input traces away from sensitive analog or high-speed digital nodes. Confirm the board ground and cable shield arrangement before field deployment because connector-level ESD protection alone does not eliminate conducted noise entering through the cable. This product record combines the MAX3221ECDBRG4 electrical characteristics, package information, interface ratings, drop-in alternatives, comparison parameters, and practical layout guidance in one engineering-focused reference. It supports component selection, PCB footprint review, and RS-232 interface design without relying on a generic interface-IC overview.

RFQ Contact
MAX3221ECPWG4 - 3V RS-232 Transceiver | Texas Instruments
MAX3221ECPWG4

MAX3221ECPWG4 - 3V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221ECPWG4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply, with one driver, one receiver, and enhanced ±15 kV IEC ESD protection in a 16-pin TSSOP package. The MAX3221ECPWG4 is designed for compact serial-interface equipment requiring a single RS-232 channel and a low-voltage digital supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic levels. The MAX3221ECPWG4 belongs to the line-transceiver hierarchy within interface ICs. Its integrated charge-pump circuitry supports single-supply operation, while the driver and receiver provide the physical layer required to connect a host, controller, or embedded system to an RS-232 port. The device operates across a 3 V to 5.5 V supply range and includes one line driver and one line receiver. According to the manufacturer description, its RS-232 pins provide protection of ±15 kV under the IEC human-body model, ±8 kV under the IEC 61000-4-2 contact-discharge test, and ±15 kV under the IEC 61000-4-2 air-gap-discharge test. These ratings are intended for protecting exposed serial-port connectors against electrostatic discharge. The MAX3221ECPWG4 uses a 16-terminal gull-wing surface-mount package with a 0.65 mm terminal pitch. The package body is identified as 4.40 mm wide, and the manufacturer markets the device as a commercial-temperature-grade part. Its single-channel architecture makes it appropriate where only one transmit and one receive path is needed, avoiding the extra drivers, receivers, and package area associated with a multi-channel transceiver. Typical uses include single-port RS-232 console connections, industrial equipment interfaces, point-of-sale terminals, data-acquisition equipment, and service or configuration ports. The 3 V to 5.5 V operating range allows the transceiver to share power with 3.3 V or 5 V system logic, reducing the need for a separate 5 V-only interface supply in many designs. PCB design should preserve the manufacturer-recommended connection and bypass layout, place charge-pump capacitors close to their associated pins, and route the RS-232 driver outputs toward the connector. The communication lines should remain away from sensitive analog or high-speed digital traces where practical. Confirm every pin function and capacitor value against the manufacturer pin description and application schematic before releasing a layout. This product page combines the MAX3221ECPWG4 electrical ratings, package characteristics, RS-232 application context, and qualified drop-in alternatives with practical PCB and protection guidance. It is structured to help engineers identify whether the single-channel 16-pin TSSOP device fits a connector, industrial-control, or embedded serial-interface design.

RFQ Contact
MAX3221ECPWR - 250kbps Single RS-232 Transceiver | Texas Instruments
MAX3221ECPWR

MAX3221ECPWR - 250kbps Single RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221ECPWR is a 3 V to 5.5 V single-channel RS-232 line driver and receiver capable of signaling at 250 kbps, with plus or minus 15 kV ESD protection across the serial-port pins. It is packaged in a 16-pin TSSOP and includes one line driver, one line receiver with a dedicated enable function, and a dual charge-pump circuit. The MAX3221ECPWR provides the electrical interface between an asynchronous communication controller and a serial-port connector while meeting the requirements of TIA/EIA-232-F. An RS-232 transceiver is an interface IC that converts logic-level signals from a UART or microprocessor into RS-232 voltage levels and converts incoming RS-232 signals back into CMOS-compatible logic. The RS-232 interface belongs to the interface IC hierarchy, where it bridges digital controllers, embedded systems, industrial equipment, and external serial peripherals. The MAX3221E family is designed for single-channel links where a second driver and receiver would add cost and board area without improving the application. The device operates from a single 3 V to 5.5 V supply, making it suitable for both 3.3 V and 5 V systems. Its internal dual charge-pump circuit generates the positive and negative voltages required by the TIA/EIA-232-F interface without a separate bipolar supply. Data rates up to 250 kbps support legacy serial communication, industrial control links, data acquisition equipment, configuration ports, and service interfaces. Plus or minus 15 kV ESD protection strengthens the serial connector against electrostatic discharge. The receiver includes a dedicated enable function that can place the receiver in a high-impedance state, while the driver-side enable structure supports controlled interface operation. The MAX3221ECPWR combines these functions in a compact 16-pin TSSOP, allowing a complete RS-232 port to be implemented with a small PCB footprint. Its single-channel architecture is appropriate for point-to-point serial links rather than multi-drop RS-485 networks. Typical uses include industrial equipment interfaces, laboratory instrumentation, cash-register systems, embedded control panels, and legacy peripheral connections. The 250 kbps maximum data rate exceeds the throughput of many legacy RS-232 ports while retaining compatibility with established TIA/EIA-232-F designs. The 3 V to 5.5 V operating range also allows the same interface topology to be used across mixed-voltage systems. When laying out the circuit, place the charge-pump capacitors and supply bypass capacitor close to their corresponding pins, and route the driver output and receiver input away from noisy digital signals. Use the manufacturer datasheet pin-description table to verify signal assignments and the exposed ground connection before assigning PCB tracks.

RFQ Contact
MAX3221ECTE+ - 3V/5V RS-232 Transceiver | Maxim Integrated
MAX3221ECTE+

MAX3221ECTE+ - 3V/5V RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX3221ECTE+ is a 3 V to 5.5 V RS-232 transceiver supporting data rates up to 250 kbps in a 16-pin TQFN package measuring 5 mm by 5 mm. The device combines one RS-232 transmitter, one receiver, ±15 kV ESD protection, and automatic shutdown and wakeup functions in a single integrated interface IC. It is designed for compact equipment requiring a standards-compliant EIA/TIA-232 connection between a host UART and an external data cable. An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential, bipolar RS-232 levels and converts received RS-232 levels back into logic-compatible signals. The MAX3221ECTE+ operates from a single 3.0 V to 5.5 V supply, making it suitable for systems using either 3.3 V or 5 V logic. Its automatic shutdown circuitry reduces supply demand when the interface is inactive, while wakeup support allows operation to resume when valid serial data arrives. The principal electrical features include a maximum data rate of 250 kbps, ±15 kV ESD protection, and a shutdown current of 1 µA. The integrated protection is particularly valuable in industrial control, instrumentation, and data-acquisition equipment where an RS-232 connector may be exposed to electrostatic discharge. The device also supports EIA/TIA-232 and V.28/V.24 communication requirements while presenting a compact, board-space-efficient interface to the host controller. MAX3221ECTE+ combines a transmitter and receiver in one package, avoiding separate logic-level conversion devices for each direction. The 5 mm by 5 mm TQFN footprint supports dense control boards, but its exposed pad requires careful PCB layout and adequate thermal dissipation. Charge-pump circuitry internally develops the positive and negative RS-232 voltage levels needed by the transmitter, so the application circuit requires the external components and connections specified by the manufacturer datasheet. Typical uses include industrial serial controllers, test and measurement equipment, POS terminals, embedded serial bridges, and isolated or long-distance RS-232 links. At 250 kbps, the interface is fast enough for moderate-speed telemetry and configuration traffic while maintaining compatibility with conventional RS-232 ports. For designs operating from 5 V, the wide 3.0 V to 5.5 V supply range also provides flexibility when the host uses a lower-voltage rail. Use the manufacturer pin description and application circuit when assigning the TQFN land pattern, connecting the exposed pad, and placing bypass or charge-pump capacitors. Keep the interface path away from sensitive analog signals, provide a low-impedance ground connection, and keep external cables and connectors as short as practical. ESD protection reduces connector risk but does not replace correct grounding, shielding, and surge-protection design. This page consolidates the device specifications, verified package information, sourcing guidance, drop-in alternatives, and practical RS-232 layout considerations. It also distinguishes the electrically useful alternatives from package or temperature options that require additional design review before substitution.

RFQ Contact
MAX3221ECTE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECTE+T

MAX3221ECTE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221ECTE+T is a single-channel RS-232 transceiver rated for data rates up to 250 kbps, operating from a 3.0 V to 5.5 V supply in a 16-pin TQFN package. It provides ±15 kV ESD protection and uses the MAX3221 family AutoShutdown feature to reduce supply current to 1 µA when no valid receiver signal is detected. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host or controller and a RS-232 port. Within the interface hierarchy, the MAX3221ECTE+T belongs to the RS-232 transceiver class, then to line-driver and line-receiver circuits, and ultimately to the broader communication-interface and semiconductor categories. Its charge-pump circuitry generates the bipolar voltage levels required by the RS-232 standard without a separate negative supply. Key features include a 250 kbps maximum data rate, a 3.0 V to 5.5 V operating range, ±15 kV ESD protection, and 1 µA shutdown supply current. The device provides one transmit channel and one receive channel, making it suitable for compact point-to-point serial links. AutoShutdown reduces power consumption when the receiver detects no valid RS-232 activity, while automatic wakeup permits the circuit to resume operation when a valid signal returns. The MAX3221 architecture integrates the transmitter, receiver, interface control, and charge-pump functions into one package. This consolidation simplifies PCB design by reducing the number of external interface components. The transmitter converts TTL/CMOS logic levels into RS-232 levels, while the receiver converts bipolar RS-232 inputs into a CMOS-compatible output. Internal protection and controlled slew behavior support reliable communication over cable connections exposed to electrostatic discharge. Typical applications include industrial serial consoles, data-acquisition equipment, point-of-sale terminals, test and measurement instruments, and embedded control systems that require an RS-232 port with automatic power management. The 3.0 V minimum supply voltage also makes the device suitable for mixed 3.3 V and 5 V systems when the interface requires full RS-232 electrical levels rather than TTL signaling. When laying out the circuit, place the charge-pump capacitors and the interface bypass capacitor close to their associated pins, and route the RS-232 connector traces away from sensitive analog or high-speed digital nets. Confirm the logic levels and polarity of the connected host because RS-232 is a single-ended, inverted bipolar interface and is not directly interchangeable with TTL UART signaling.

RFQ Contact
MAX3221ECUE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECUE+T

MAX3221ECUE+T - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221ECUE+T is a 3.0V to 5.5V single-channel RS-232 transceiver with one driver and one receiver, a 250kbps maximum data rate, ±15kV ESD protection, and automatic shutdown and wakeup in a 16-pin TSSOP package. It is designed for compact serial interfaces that require reliable EIA/TIA-232 signal conditioning from a 3.3V or 5V supply. An RS-232 transceiver is an interface IC that converts logic-level UART signals between a host controller and a cable-based RS-232 port. It belongs to the RS-232 transceiver category, which sits within the broader hierarchy of interface ICs, communication semiconductors, and discrete analog-and-digital interface components. Unlike logic-level UART links, the RS-232 side uses bipolar voltage levels and requires controlled edge rates to meet communication and electromagnetic-interference requirements. The MAX3221ECUE+T combines a transmitter and receiver in one compact package. Key features include operation from 3.0V to 5.5V, data rates up to 250kbps, ±15kV ESD protection, and a low 1µA shutdown supply current. Its AutoShutdown function reduces power consumption when the receiver does not detect a valid signal. These characteristics make it useful where energy use, board area, and port reliability are important. Maxim's charge-pump architecture generates the positive and negative voltages required by the RS-232 transmitter while the device operates from a single low-voltage supply. Four small external capacitors support this function. The integrated transmitter adds controlled signal shaping, while the receiver translates the bipolar RS-232 input into a CMOS-compatible logic level for the host UART. Automatic wakeup supports systems that periodically power their communications port. Typical uses include industrial control equipment, point-of-sale terminals, instrumentation, maintenance equipment, and embedded serial-port adapters. The device is also appropriate for portable or industrial systems that need a single RS-232 channel rather than the multiple drivers and receivers offered by larger interface families. A 3.3V system can use the same part as a 5V system, subject to the external interface and logic-level requirements of the connected controller. PCB layout is critical because the charge-pump capacitors must be placed close to their associated pins, while the RS-232 connector path should remain as short and separated from sensitive circuitry as practical. Keep the connector-side return path continuous, route driver and receiver traces away from switching nodes, and use the device pin-description table when assigning connector and logic nets. This product record combines device specifications, verified source links, package information, application guidance, and engineering-focused comparisons. It also identifies genuine same-package alternatives and explains when their electrical or qualification differences matter, helping designers evaluate replacement options without overlooking board-layout or operating constraints.

RFQ Contact
MAX3221EEAE+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EEAE+

MAX3221EEAE+ - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221EEAE+ is a single-driver, single-receiver RS-232 transceiver designed for portable and embedded equipment. It operates from 3.0V to 5.5V, supports data rates up to 250kbps, and is housed in a 16-pin SSOP package. The MAX3221E family also provides automatic shutdown and wake-up functions plus enhanced electrostatic-discharge protection on all transmitter outputs and receiver inputs. An RS-232 transceiver is an interface IC that converts a logic-level UART signal into RS-232 voltage levels and converts an incoming RS-232 signal back into CMOS-compatible logic. It belongs to the communication-interface hierarchy: RS-232 transceiver, line-driver and receiver interface, interface IC, and semiconductor. This bidirectional conversion allows a modern microcontroller or processor to communicate with legacy printers, industrial equipment, data terminals, and other RS-232 systems. The MAX3221EEAE+ combines a 3.0V to 5.5V supply range with a maximum data rate of 250kbps. Its AutoShutdown feature reduces supply current to 1uA when the system is inactive, helping conserve power in handheld and battery-operated equipment. Enhanced ESD protection rated to 15kV adds protection for the physical RS-232 connector interface, where cables can introduce electrostatic discharge into the equipment. The device uses a charge-pump-assisted interface architecture to generate the positive and negative voltages required by RS-232 while operating from a single low-voltage supply. One transmitter and one receiver support one complete bidirectional communication channel. The MAX3221 is the 16-pin member of the MAX3221E, MAX3223E, and MAX3243E interface family, while MAX3223E and MAX3243E provide additional driver or receiver channels for multi-port designs. Typical uses include handheld test equipment, portable data-collection systems, industrial serial adapters, point-of-sale terminals, and equipment with a legacy RS-232 port. The 16-pin SSOP package is useful when a compact interface is required without adding a larger multi-channel transceiver. The combination of low-voltage operation, 250kbps performance, AutoShutdown, and 15kV ESD protection makes the part appropriate for portable equipment that must maintain reliable serial connectivity. Designers should follow the manufacturer datasheet for capacitor selection, charge-pump layout, and RS-232 connector protection. Place the required charge-pump capacitors close to their associated pins, route the interface nets away from sensitive analog circuitry, and provide the specified bypass capacitance at the supply pins. The external RS-232 connector should also receive suitable protection appropriate to the cable length and environmental exposure. This page combines manufacturer specifications, packaging information, practical interface-design guidance, and technically meaningful drop-in comparisons. These engineering details help shorten component selection and PCB-layout work while making the trade-offs among the MAX3221E grade and package-ordering options easier to assess.

RFQ Contact
MAX3221EEAE+G071 - 250kbps RS-232 Transceiver | Maxim
MAX3221EEAE+G071

MAX3221EEAE+G071 - 250kbps RS-232 Transceiver | Maxim

Maxim Integrated MAX3221EEAE+G071 is a single-channel RS-232 transceiver IC with 3.0V to 5.5V operation, a maximum data rate of 250kbps, 1uA shutdown current, and ±15kV ESD protection. The device contains one line driver and one line receiver and is packaged in a 16-SSOP package. An RS-232 transceiver is an interface IC that translates logic-level signals between a computer or embedded controller and a RS-232 communications link. The driver converts a low-voltage digital signal into RS-232 levels, while the receiver converts an incoming RS-232 signal into a logic-compatible signal. In the electronics hierarchy, the MAX3221EEAE+G071 belongs to the interface IC class and specifically implements an EIA/TIA-232 communications interface with automatic shutdown and wake-up behavior. The 3.0V to 5.5V supply range allows operation from regulated 3.3V and 5V systems. Its 250kbps maximum data rate supports legacy serial links used in point-to-point equipment, industrial controllers, data-acquisition systems, and service interfaces. Automatic shutdown reduces supply current to 1uA when no valid receiver signal is detected, helping conserve power in systems that spend substantial time idle. The integrated ±15kV ESD protection strengthens the external serial interface against electrostatic discharge events. The MAX3221EEAE+G071 uses Maxim Integrated's charge-pump interface architecture to generate the bipolar voltage levels required by RS-232 from a single low-voltage supply. One transmitter and one receiver make it suitable for designs requiring a single serial data path rather than multiple RS-232 channels. Automatic wake-up allows the device to return to operating mode after a valid signal appears, reducing the need for external power-management logic around the serial port. Typical applications include industrial control equipment, instrumentation, data-logging systems, configuration ports, service and debug interfaces, and embedded serial adapters. It is particularly useful where low standby consumption is important and where the host operates from either 3.3V or 5V power. The 16-SSOP package also supports compact board layouts where a larger SOIC or dual-channel transceiver would be unnecessary. When laying out a board, place the charge-pump capacitors and the RS-232 interface components directly beside the IC according to the manufacturer's pin-description and typical-application diagrams. Route the exposed RS-232 connector pins away from sensitive low-level circuitry, and provide the specified power and ground-plane connections to minimize return-path disturbance. This product page combines interface specifications, package details, application guidance, and a parameter-focused comparison with compatible RS-232 transceiver options. It also identifies design considerations for power management, ESD protection, signal routing, and component replacement so engineers can evaluate the device before integrating it into a new board.

RFQ Contact
MAX3221EEAE+TG071 - 250kbps RS-232 Transceiver | Maxim
MAX3221EEAE+TG071

MAX3221EEAE+TG071 - 250kbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3221EEAE+TG071 is a single-channel RS-232 line-driver and receiver transceiver rated for 250 kbps, operating from a 3.0 V to 5.5 V supply in a 16-pin SSOP package. Its principal features include ±15 kV ESD protection, approximately 1 µA shutdown current, and automatic shutdown and wake-up behavior. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals from a host, controller, or embedded system into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. In the product hierarchy, the MAX3221EEAE+TG071 is an RS-232 transceiver within the interface IC and communications-semiconductor categories. The device includes one transmitter and one receiver, making it suitable for point-to-point serial links. Its 3.0 V to 5.5 V operating range supports both 3.3 V and 5 V systems. Automatic shutdown reduces supply consumption when no valid receiver activity is detected, while automatic wake-up restores operation after valid data returns. The ±15 kV ESD protection improves ruggedness on exposed cable and connector interfaces. The MAX3221E family uses an on-chip charge pump and four small external capacitors to generate the bipolar voltage required by an RS-232 transmitter from a single positive supply. This arrangement eliminates the need for a separate negative supply rail. The MAX3221 variant has one driver and one receiver in 16 pins, distinguishing it from the two-channel MAX3223 and the higher-channel-count MAX3243. Typical applications include industrial equipment serial ports, configuration and programming interfaces, point-of-sale terminals, barcode and data-acquisition equipment, laboratory instruments, and embedded control systems. The 250 kbps capability suits legacy asynchronous RS-232 communication where full-duplex point-to-point connectivity is required rather than a multi-drop bus. When laying out the PCB, keep the four charge-pump capacitors close to their specified pins and provide the receiver interface with appropriate ESD protection and controlled return paths. Confirm that the external connector, cable, and logic controller can support the selected signaling rate before treating 250 kbps as an end-to-end guaranteed throughput. This page combines the exact MAX3221EEAE+TG071 ordering code with package details, functional comparisons, application guidance, and design considerations. It also distinguishes true pin-compatible replacements from similarly packaged devices whose channel count or data rate makes them unsuitable for a direct PCB substitution.

RFQ Contact
MAX3221EEAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EEAE+TG1Z

MAX3221EEAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EEAE+TG1Z is a single-supply EIA/TIA-232 RS-232 transceiver with one driver and one receiver, operating from 3.0V to 5.5V, supporting data rates up to 250kbps, and featuring enhanced electrostatic discharge protection rated at plus or minus 15kV. The device is packaged in a 16-pin SSOP package and includes automatic shutdown and wake-up features. An RS-232 transceiver is an interface IC that translates logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the broader hierarchy of interface ICs, serial transceivers, communication interfaces, and semiconductor devices. The MAX3221EEAE+TG1Z is intended for equipment that needs one serial channel with low supply voltage, automatic power management, and stronger ESD protection than a basic RS-232 interface. The principal features include a 3.0V to 5.5V operating supply range, operation at up to 250kbps, a 1uA shutdown current, plus or minus 15kV ESD protection, and automatic shutdown and wake-up. These characteristics suit compact industrial controls, test equipment, point-of-sale terminals, and embedded serial ports. The single driver and single receiver arrangement also makes the MAX3221 a compact choice when one RS-232 link is sufficient. MAX3221E-family devices use charge-pump circuitry to generate the positive and negative voltage levels required by RS-232, allowing operation from a single low-voltage supply. The automatic shutdown function reduces supply current when the interface is inactive, while wake-up support helps the system recover without continuous high-power operation. The 16-pin SSOP outline supports conventional surface-mount assembly and compact board layouts. Typical applications include industrial serial adapters, programmable-logic-controller communication, barcode and point-of-sale equipment, instrumentation, and embedded control systems. For designs using a 3.3V or 5V logic supply, the MAX3221EEAE+TG1Z can provide a protected RS-232 connection without a separate negative power rail. Its one-channel architecture should be selected when the system does not require multiple RS-232 drivers or receivers. The main design consideration is ensuring that the external charge-pump capacitors, transceiver signal lines, and logic-side connections follow the pin-description and application-circuit guidance in the manufacturer datasheet. Place the charge-pump capacitors close to their specified pins and preserve the recommended protection-network arrangement on external RS-232 connectors. Confirm that the selected logic levels and supply voltage match the host controller. This page combines the manufacturer product information, package details, verified comparison candidates, and practical interface-design guidance. It also identifies where detailed pin assignments, environmental ratings, and lifecycle-specific technical parameters should be confirmed in the official MAX3221 documentation.

RFQ Contact
MAX3221EEAE-T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EEAE-T

MAX3221EEAE-T - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221EEAE-T is a 3.0V to 5.5V powered RS-232 transceiver with one driver, one receiver, automatic shutdown and wakeup, and ±15kV ESD protection in a 16-pin SSOP package. It supports data rates up to 250kbps and is packaged for tape-and-reel production handling. An RS-232 transceiver is an interface IC that converts logic-level serial signals between a host or controller and the voltage-defined RS-232 bus. The MAX3221EEAE-T belongs to the RS-232 interface hierarchy, where a transceiver combines a transmitter for outbound data with a receiver for inbound data. Its single-driver, single-receiver arrangement is intended for point-to-point serial links and portable equipment requiring compact implementation. The MAX3221EEAE-T operates from 3.0V to 5.5V, supports signaling rates through 250kbps, and provides ±15kV ESD protection. AutoShutdown reduces supply current to 1µA when no valid receiver signal is detected, while automatic wakeup reactivates the interface when valid data returns. These characteristics make the device useful where serial connectivity must coexist with strict power-consumption limits. Internally, the device combines its RS-232 driver and receiver functions with on-board charge-pump support, enabling operation from a single 3.0V to 5.5V supply rather than a bipolar ±5V source. The enhanced ESD protection is intended to improve tolerance to electrostatic discharge encountered during cable connection, removal, and industrial or commercial handling. Typical uses include industrial serial adapters, data-acquisition equipment, POS terminals, barcode scanners, test instruments, and embedded systems that exchange data with RS-232 peripherals. The 250kbps capability suits moderate-speed command and control links, while the low-power shutdown behavior benefits portable or intermittently connected systems. PCB design should account for the 16-pin SSOP footprint, place the charge-pump capacitors as close as practical to their designated pins, and keep the RS-232 driver outputs and receiver inputs away from sensitive high-speed traces. Confirm the capacitor values, supply bypassing, and charge-pump layout against the manufacturer datasheet before releasing the PCB. This product page combines the manufacturer family specifications, exact ordering information, structured alternatives, package details, and practical interface-design guidance to support component selection and board-layout planning.

RFQ Contact
MAX3221EEAE/GG8 - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EEAE/GG8

MAX3221EEAE/GG8 - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EEAE/GG8 is a 3.0V to 5.5V powered, single-transmitter/single-receiver RS-232 transceiver with automatic shutdown and wake-up, 250kbps data-rate capability, and ±15kV ESD protection in a 16-pin SSOP package. It is designed for low-power serial-interface systems requiring EIA/TIA-232 and V.28/V.24-compatible signal levels. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX3221E family combines one transmit channel and one receive channel with low-power 3V operation, making it suitable for embedded equipment, industrial controllers, point-of-sale terminals, and other systems that exchange data over short-distance serial links. The device operates from a 3.0V to 5.5V supply, supports data rates up to 250kbps, and includes enhanced electrostatic-discharge protection of ±15kV. Automatic shutdown and wake-up functions reduce supply current when the interface is inactive, while transmitter and receiver enable pins support controlled power management in systems with multiple peripheral connections. MAX3221EEAE/GG8 uses the MAX3221E single-channel architecture, providing one RS-232 transmitter and one receiver rather than the multiple-channel arrangement used by some larger transceivers. Its 16-pin SSOP package supports compact PCB layouts, and the industrial-temperature ordering option is identified by the GG8 package and temperature suffix. Typical applications include serial adapters, test equipment, industrial control interfaces, barcode scanners, embedded data-collection systems, and communication links between a host controller and an external RS-232 peripheral. The 250kbps capability is appropriate for legacy serial protocols and control traffic that do not require modern high-speed differential interfaces. When designing the circuit, place the charge-pump capacitors and interface-protection components close to the device and route the RS-232 connector signals away from sensitive analog and digital signal paths. Confirm the supply voltage, logic levels, connector pinout, and charge-pump capacitor values against the manufacturer datasheet before releasing the PCB layout. This page combines the device specifications, package information, application guidance, design considerations, and drop-in alternatives into a practical engineering reference for selecting and implementing the MAX3221EEAE/GG8.

RFQ Contact
MAX3221EETE+T - 250kbps AutoShutdown RS-232 | Analog Devices
MAX3221EETE+T

MAX3221EETE+T - 250kbps AutoShutdown RS-232 | Analog Devices

The Analog Devices MAX3221EETE+T is a 3.0V to 5.5V RS-232 transceiver with one transmitter and one receiver, 250 kbps operation, and ±15 kV ESD protection in a 16-pin TQFN package with an exposed pad. The MAX3221E family also provides automatic shutdown and wakeup, with supply current reduced to 1 µA when no valid receiver signal is detected. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar, inverted signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, where it bridges UART, UART-compatible controller, and peripheral circuitry with legacy or industrial communications ports. The MAX3221E supports the EIA/TIA-232 and V.28/V.24 signaling requirements identified for the MAX3221E family. The MAX3221EETE+T combines a 250 kbps data rate with a 3.0V to 5.5V supply range, allowing operation alongside both 3.3V and 5V digital systems. Its AutoShutdown circuit recognizes when connected equipment is powered off or no valid signal appears on a receiver input, then disables the internal charge pump and drivers to reduce power consumption. Automatic wakeup restores operation when a valid signal returns. The enhanced electrostatic-discharge design protects the transmitter outputs and receiver inputs against ±15 kV ESD events. This protection is particularly useful for cables connected to external equipment, where electrostatic discharge can enter through a connector rather than through the protected logic-side pins. The device converts one TTL or CMOS data channel into an RS-232 signal and converts one inbound RS-232 signal back into a logic-level output. Typical uses include industrial serial adapters, test and measurement equipment, point-of-sale terminals, security systems, and embedded systems that retain an RS-232 port. The 250 kbps capability supports substantially faster communication than conventional low-speed RS-232 links, while the small TQFN package suits compact control boards. Systems requiring more than one RS-232 port normally require additional transceiver channels or a multichannel interface family. When laying out the PCB, place the charge-pump capacitors and interface capacitors close to their designated pins, connect the exposed thermal pad to the ground plane, and keep the RS-232 traces away from sensitive clock, sensor, and analog signals. Confirm capacitor values, voltage ratings, and exposed-pad soldering requirements against the manufacturer datasheet before fabrication. This product page combines the manufacturer interface specifications with package, sourcing, application, and replacement guidance. It also highlights practical ESD, layout, power-management, and signal-integrity considerations that engineers can apply when integrating the MAX3221EETE+T into a compact RS-232 circuit.

RFQ Contact
MAX3221EEUE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EEUE+T

MAX3221EEUE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EEUE+T is a single-transceiver RS-232 interface IC with one transmitter and one receiver, a maximum data rate of 250 kbps, and operation from 3.0 V to 5.5 V. It is packaged in a 16-pin TSSOP and includes enhanced electrostatic-discharge protection rated at ±15 kV. The MAX3221E family also provides automatic shutdown and wake-up behavior to reduce supply consumption when the connected RS-232 link is inactive. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. It belongs to the interface IC hierarchy alongside UART transceivers, line drivers, and level shifters. The MAX3221EEUE+T is designed for equipment that requires one bidirectional RS-232 connection, such as configuration ports, service interfaces, point-of-sale terminals, and industrial control systems. Key operating characteristics include a 3.0 V to 5.5 V supply range, full-duplex operation, and data rates up to 250 kbps. Its enhanced ESD protection helps the interface withstand electrostatic discharge on exposed RS-232 connections. AutoShutdown reduces the supply current to approximately 1 µA when no valid receiver signal is detected, while automatic wake-up returns the device to an active state when a valid signal appears. The MAX3221E/MAX3223E/MAX3243E family supports EIA/TIA-232 and V.28/V.24 communication interfaces. The MAX3221EEUE+T combines one driver and one receiver in a compact 16-pin TSSOP, making it suitable for space-constrained designs that require a single RS-232 port. Its 250 kbps capability supports faster service and data links than conventional low-speed RS-232 implementations. Typical applications include industrial controller service ports, point-of-sale and retail equipment, test systems, security consoles, and embedded control boards. The device is particularly useful when the system must operate from a 3.3 V supply while communicating with a legacy RS-232 peripheral or computer port. PCB design should keep the RS-232 connector and protection network close to the transceiver while maintaining separation from sensitive analog or high-speed digital traces. Follow the manufacturer datasheet for external charge-pump capacitor values, receiver and transmitter connection details, and the complete 16-pin assignment before finalizing the layout. This page combines the exact ordering information, RS-232 operating characteristics, package details, sourcing options, and application guidance needed to evaluate the MAX3221EEUE+T for a new interface design.

RFQ Contact
MAX3221EIDB - 250kbps 3V-5.5V RS-232 Transceiver | TI
MAX3221EIDB

MAX3221EIDB - 250kbps 3V-5.5V RS-232 Transceiver | TI

Texas Instruments MAX3221EIDB is a single-channel RS-232 line driver and receiver operating from a single 3V to 5.5V supply at up to 250kbps, with one transmitter, one receiver, and a 16-pin SSOP package. Its RS-232 connector-side pins provide IEC 61000-4-2 ESD protection, and the device meets TIA/EIA-232-F requirements. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a serial port. The MAX3221E combines a differential line driver, receiver, dual charge-pump circuit, and automatic signal generation in one package. It occupies the interface ICs level within the broader communications and industrial-control hierarchy, where reliable voltage translation, electrostatic-discharge protection, and economical PCB integration are important. The device provides one full-duplex RS-232 channel with a maximum data rate of 250kbps. Its single 3V to 5.5V supply operation allows use with both 3.3V and 5V systems. The integrated charge pump produces the bipolar voltage levels required by RS-232 while reducing the number of external components to four small capacitors. IEC 61000-4-2 protection on the serial-port connection pins adds protection where cables enter an enclosure. The MAX3221E implements one driver and one receiver with a dedicated receiver-enable function. It provides the electrical interface between an asynchronous communication controller and an RS-232 connector while satisfying TIA/EIA-232-F requirements. This architecture suits point-to-point links that do not require multiple RS-232 channels, such as service-console, configuration-port, industrial-controller, and legacy peripheral connections. Typical applications include single-port RS-232 adapters, programmable logic controller service interfaces, industrial control equipment, test fixtures, and embedded systems that retain a legacy serial connector. The 16-pin SSOP package supports compact, surface-mount PCB construction, while the 250kbps rate is suitable for moderate-speed asynchronous data transfer rather than high-bandwidth protocols. Designers should follow the manufacturer’s recommended capacitor values and placement guidance for the charge-pump circuit. Keep the external capacitors close to their designated pins, route the RS-232 connector-side nets away from sensitive logic, and use a suitable protection network when cables extend beyond the protected board boundary. Verify that the host voltage levels and connector pin assignment match the selected logic family. This product page combines the MAX3221EIDB electrical characteristics, package details, available drop-in alternatives, comparison parameters, and application-specific design guidance. It is intended to accelerate component selection, PCB planning, and RS-232 interface qualification without requiring the reader to reconstruct the design trade-offs from separate listings.

RFQ Contact
MAX3221EIDBG4 - Single-Channel 3V RS-232 Transceiver | Texas Instruments
MAX3221EIDBG4

MAX3221EIDBG4 - Single-Channel 3V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221EIDBG4 is a single-channel RS-232 line transceiver with one driver and one receiver, a 3 V to 5.5 V supply range, and operation up to 250 kbps. The device is housed in a 16-pin SSOP package. Its serial-port pins provide ±15 kV ESD protection, and the circuit includes a dual charge-pump supply for compliant RS-232 signal levels. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a serial connector. The transmitter converts TTL or CMOS logic into bipolar RS-232 levels, while the receiver converts the bipolar signal back into logic-compatible levels. The MAX3221 therefore connects an asynchronous communication controller to a serial port without requiring external RS-232 line drivers or receivers. The MAX3221EIDBG4 offers a flexible 3 V to 5.5 V operating supply and a maximum signaling rate of 250 kbps. According to the manufacturer datasheet, the device meets TIA/EIA-232-F requirements and incorporates a dual charge-pump circuit. Dedicated receiver enable support allows the receiver to be controlled when the serial interface is not active. The E and I ordering designations identify the industrial-temperature version in the SSOP package family, while G4 identifies the tape-and-reel shipping format. The 16-pin SSOP has a stated body width of approximately 5.30 mm and a package width of 0.209 inch. Lead-free status and industrial temperature grade are explicitly listed for this device. Typical uses include industrial serial adapters, point-to-point RS-232 links, embedded data acquisition equipment, maintenance interfaces, and legacy peripheral connections. A single transceiver is appropriate when only one RS-232 channel is needed. Multiport systems generally require additional transceiver channels or a multi-channel interface IC. PCB design should keep charge-pump capacitors and RS-232 connector protection close to the relevant pins. Confirm the complete pin assignment, exposed supply requirements, and recommended capacitor values in the manufacturer datasheet before releasing a layout. External transient protection may still be required when the connector is exposed to severe industrial surge environments. This product page combines the device specifications, package information, application guidance, lifecycle information, and verified cross-reference findings for faster engineering review. It also highlights the limitation that no independently verified, same-package drop-in alternatives could be confirmed without risking an incorrect PCB substitution.

RFQ Contact
MAX3221EIDBR - 250kbps 3V-5.5V RS-232 Transceiver | TI (Tape & Reel)
MAX3221EIDBR

MAX3221EIDBR - 250kbps 3V-5.5V RS-232 Transceiver | TI (Tape & Reel)

Texas Instruments MAX3221EIDBR is a single-channel RS-232 line driver and receiver operating from a single 3V to 5.5V supply at up to 250kbps, with one transmitter, one receiver, and a 16-pin SSOP package. Its RS-232 connector-side pins provide IEC 61000-4-2 ESD protection, and the device meets TIA/EIA-232-F requirements. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a serial port. The MAX3221E combines a differential line driver, receiver, dual charge-pump circuit, and automatic signal generation in one package. It occupies the interface ICs level within the broader communications and industrial-control hierarchy, where reliable voltage translation, electrostatic-discharge protection, and economical PCB integration are important. The device provides one full-duplex RS-232 channel with a maximum data rate of 250kbps. Its single 3V to 5.5V supply operation allows use with both 3.3V and 5V systems. The integrated charge pump produces the bipolar voltage levels required by RS-232 while reducing the number of external components to four small capacitors. IEC 61000-4-2 protection on the serial-port connection pins adds protection where cables enter an enclosure. The MAX3221E implements one driver and one receiver with a dedicated receiver-enable function. It provides the electrical interface between an asynchronous communication controller and an RS-232 connector while satisfying TIA/EIA-232-F requirements. This architecture suits point-to-point links that do not require multiple RS-232 channels, such as service-console, configuration-port, industrial-controller, and legacy peripheral connections. Typical applications include single-port RS-232 adapters, programmable logic controller service interfaces, industrial control equipment, test fixtures, and embedded systems that retain a legacy serial connector. The 16-pin SSOP package supports compact, surface-mount PCB construction, while the 250kbps rate is suitable for moderate-speed asynchronous data transfer rather than high-bandwidth protocols. Designers should follow the manufacturer’s recommended capacitor values and placement guidance for the charge-pump circuit. Keep the external capacitors close to their designated pins, route the RS-232 connector-side nets away from sensitive logic, and use a suitable protection network when cables extend beyond the protected board boundary. Verify that the host voltage levels and connector pin assignment match the selected logic family. This product page combines the MAX3221EIDBR electrical characteristics, package details, available drop-in alternatives, comparison parameters, and application-specific design guidance. It is intended to accelerate component selection, PCB planning, and RS-232 interface qualification without requiring the reader to reconstruct the design trade-offs from separate listings.

RFQ Contact