Products (44,000+)

MAX3232EEAE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEAE+TG1Z

MAX3232EEAE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEAE+TG1Z is a 3.0 V to 5.5 V, 2-driver/2-receiver, full-duplex RS-232 transceiver capable of operation up to 1 Mbps in a 16-pin SSOP package. The device provides true RS-232 levels, ±15 kV ESD protection, and low-power operation with shutdown supply current down to 10 nA. The MAX3232 family uses on-chip charge pumps to generate the positive and negative voltages required by RS-232 drivers without requiring a separate DC supply. A transceiver is an interface integrated circuit that combines digital line-driver and receiver functions with the voltage translation required to connect TTL or CMOS logic to an RS-232 port. In the broader semiconductor hierarchy, the MAX3232 is an interface transceiver, a member of the RS-232 interface IC family, and a multi-channel communications device. Its two transmitters convert logic-high and logic-low signals into RS-232 bipolar levels, while its two receivers convert those bipolar levels back into compatible logic levels. The headline operating features are a 3.0 V to 5.5 V supply range, data rates up to 1 Mbps, and ±15 kV ESD protection. The 2/2 driver-receiver arrangement supports two communications channels in each direction. Low-power shutdown capability is especially useful in battery-operated or intermittently connected equipment because the device can reduce supply current to levels down to 10 nA when the interface is not required. The MAX3232 family uses integrated charge-pump circuitry to produce the RS-232 voltage levels required by the drivers. Its receiver architecture provides a true RS-232 input threshold and is intended for noisy industrial environments where signal levels can exceed conventional logic limits. The manufacturer also identifies the MAX3232E as pin, package, and functionally compatible with industry-standard MAX232 devices, enabling careful PCB reuse when all operating conditions and enable-control requirements are checked. Typical applications include industrial serial consoles, data-acquisition equipment, instrumentation, point-of-sale terminals, and embedded systems that communicate through an RS-232 port. Because the interface operates from 3.0 V to 5.5 V, it is appropriate for modern mixed-signal systems in which the host controller may use a 3.3 V supply. Cable length and data rate must be considered together because RS-232 is a point-to-point, unbalanced interface intended primarily for shorter-distance communication. The primary design consideration is ensuring that every connector, cable, and logic interface matches the bipolar RS-232 electrical specification. Keep the transceiver close to the connector, provide the required charge-pump capacitors using the manufacturer's recommended values and layout, and reserve adequate board space for external protection if the port will be exposed to severe transients. The SSOP package also requires careful assembly planning because its lead pitch is narrower than that of a conventional SOIC package. This product page combines manufacturer specifications, package and interface details, replacement guidance, comparison parameters, and practical circuit-layout guidance. It is intended to help engineers determine whether the MAX3232EEAE+TG1Z fits an RS-232 design and how to evaluate compatible replacements before changing a released PCB.

RFQ Contact
MAX3232EEPE+ - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEPE+

MAX3232EEPE+ - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEPE+ is a 2/2 full-duplex RS-232 transceiver rated for operation from 3.0V to 5.5V, data rates up to 1Mbps, and ±15kV ESD protection, housed in a 16-pin PDIP package. It integrates two line drivers, two line receivers, and a dual charge-pump circuit that converts the low-voltage supply into the bipolar voltages required by RS-232. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a serial port. The MAX3232EEPE+ belongs to the RS-232 interface IC family, where the transceiver handles electrical signaling while the connected controller manages the protocol and data format. Two driver and two receiver channels support full-duplex point-to-point links commonly used for configuration ports, industrial equipment, test systems, and legacy computer peripherals. The device operates across a 3.0V to 5.5V supply range, allowing use with both 3.3V and 5V systems. Its maximum supported data rate is 1Mbps, while the charge-pump design eliminates the need for a separate ±12V supply. The MAX3232E family also provides ±15kV ESD protection on the serial-port connections. Receiver behavior includes a low-power mode with current down to 10nA, which helps reduce consumption when the interface is not active. The dual charge-pump circuit generates positive and negative voltage levels required to meet RS-232 signaling thresholds. Internal driver and receiver circuits handle signal translation, while external charge-pump capacitors and supply bypass capacitors support stable operation. The MAX3232E family is designed for compatibility with the industry-standard MAX232, making it useful when an existing interface design needs a modern, low-voltage, ESD-protected implementation. Typical uses include RS-232 links in industrial controllers, laboratory instruments, point-of-sale equipment, data acquisition systems, embedded service interfaces, and legacy PC peripherals. A 1Mbps capability supports higher-speed asynchronous communication, although cable length, baud rate, capacitance, grounding, and system timing still determine whether a particular installation can operate reliably at the maximum rate. The principal design consideration is PCB placement. Keep the four 0.1µF charge-pump capacitors close to their designated pins, place the supply bypass capacitor near the device, and route serial traces away from noisy clocks, switching regulators, and high-current return paths. A solid ground plane and a properly referenced connector shield improve signal integrity and reduce susceptibility to common-mode noise. This product record combines the manufacturer's electrical and packaging information with drop-in alternatives, application guidance, PCB considerations, and a parameter-by-parameter comparison. These engineering details help designers evaluate MAX3232EEPE+ for new designs and controlled replacement projects where the 16-PDIP footprint and RS-232 electrical behavior must be retained.

RFQ Contact
MAX3232EESE+ - 3V-5.5V 1Mbps RS-232 Transceiver | Maxim
MAX3232EESE+

MAX3232EESE+ - 3V-5.5V 1Mbps RS-232 Transceiver | Maxim

The Analog Devices MAX3232EESE+ is a low-power RS-232 transceiver with two drivers, two receivers, 3.0 V to 5.5 V single-supply operation, data rates up to 1 Mbps, and a 16-pin SOIC package. The E version adds ±15 kV ESD protection and supports receiver supply current down to 10 nA, making it suitable for industrial serial interfaces where both low power and connector-side protection are important. An RS-232 transceiver is the electrical interface between a modern digital controller and an RS-232 port. Its integrated line drivers convert logic-level signals into RS-232 voltage levels, while its receivers perform the opposite conversion. The MAX3232E family belongs to the broader interface-IC hierarchy: transceiver → RS-232 interface IC → serial communications interface → semiconductor. An internal dual charge pump supplies the positive and negative voltages required by RS-232 without a separate negative power supply. Key features include two transmit and two receive channels, operation from 3.0 V to 5.5 V, throughput up to 1 Mbps, and ±15 kV ESD protection on the serial-port pins. Four external 0.1 µF charge-pump capacitors support the on-chip voltage converter. The low-power receiver design can operate with supply current down to 10 nA, which benefits systems that keep a serial interface enabled for long periods or monitor a remote connection. The MAX3232E architecture simplifies board design by integrating the charge-pump circuitry, drivers, receivers, and protection functions into one device. Its 16-SOIC package exposes two driver inputs, two driver outputs, two receiver inputs, two receiver outputs, supply connections, ground, and charge-pump capacitor terminals. Logic levels remain compatible with conventional microcontroller and UART systems operating at the device supply voltage, while the external line interface uses the bipolar voltage swings required by RS-232. Typical applications include industrial control terminals, programmable-logic-controller serial ports, instrumentation, point-of-sale equipment, and embedded systems that connect a UART controller to an RS-232 connector. The 1 Mbps capability supports high-speed serial links, while ±15 kV ESD protection improves robustness when the cable is connected or disconnected in industrial environments. For reliable operation, place the four 0.1 µF charge-pump capacitors close to their designated pins, route serial outputs away from sensitive analog nodes, and connect the device ground directly to the interface ground. Confirm signal polarity and enable state before attaching the port because RS-232 uses inverted logic relative to many UART controllers. This page consolidates the device specifications, package and pin information, drop-in alternatives, and practical interface-circuit guidance into a design-focused reference. It also highlights the differences between the standard MAX3232 and the ESD-protected MAX3232E family for replacement and sourcing decisions.

RFQ Contact
MAX3232EESE+T - 1Mbps RS-232 Transceiver | Maxim Integrated
MAX3232EESE+T

MAX3232EESE+T - 1Mbps RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX3232EESE+T is a 3.0V to 5.5V, low-power RS-232 transceiver with two drivers and two receivers in a 16-pin SOIC package. It supports data rates up to 1Mbps and provides true RS-232 operation for portable equipment, industrial controls, and other systems requiring a compact asynchronous serial interface. A true RS-232 transceiver belongs to the interface IC category and converts logic-level UART signals between a host controller and a RS-232 port. The MAX3232EESE+T integrates two line drivers, two line receivers, and a dual charge-pump circuit. This integration allows the device to generate the positive and negative voltages required by RS-232 while operating from a single low-voltage supply. The principal features include a 3.0V to 5.5V operating range, operation at data rates up to 1Mbps, and low supply consumption down to 10nA for the MAX3232E family. The E version adds ±15kV ESD protection according to the Analog Devices product page. Four external 0.1µF charge-pump capacitors support the internal voltage-conversion circuit without requiring a large external power-supply network. The MAX3232E device is designed around the EIA/TIA-232-F interface requirements and is identified as a production product by Analog Devices. Its dual charge-pump architecture maintains compatible RS-232 voltage levels without a separate bipolar supply. The 16-SOIC package also makes the MAX3232EESE+T suitable for conventional surface-mount assembly and board-space-constrained serial-port designs. Typical applications include RS-232 ports for industrial equipment, test and measurement instruments, point-of-sale terminals, data-acquisition systems, and embedded control products. The two-driver, two-receiver arrangement supports bidirectional communication, while the single 3.0V to 5.5V supply simplifies connection to modern low-voltage UART controllers. Layout should prioritize short traces for the charge-pump capacitors and maintain the manufacturer-specified capacitor values and polarity. The external capacitors must connect close to their designated pins, and the RS-232 connector interface should be isolated from sensitive analog or high-speed digital paths to minimize noise pickup. This page combines the exact MAX3232EESE+T interface specifications with package guidance, application selection, verified source links, and engineering-focused comparisons. These details help designers distinguish electrical alternatives from genuine pin-compatible SOIC-16 replacements before updating an existing RS-232 design.

RFQ Contact
MAX3232EETE+ - 1Mbps Dual RS-232 Transceiver | Analog Devices
MAX3232EETE+

MAX3232EETE+ - 1Mbps Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EETE+ is a dual-channel RS-232 transceiver with two drivers and two receivers, operation from 3.0 V to 5.5 V, data rates up to 1 Mbps, and ±15 kV ESD protection in a 16-pin TQFN (5 mm × 5 mm) package. The device provides the electrical interface between an asynchronous communication controller and a serial connector while operating from a single 3.0 V to 5.5 V supply. An RS-232 transceiver is an interface integrated circuit that converts logic-level transmit and receive signals into RS-232 line levels and back again. In the broader hierarchy, a transceiver belongs to the interface IC family, connects communication controllers to physical serial links, and is commonly used wherever reliable point-to-point serial communication must cross a cable or connector boundary. The MAX3232E family combines two RS-232 drivers, two RS-232 receivers, and a dual charge-pump circuit in one package. Key features include a 3.0 V to 5.5 V operating range, operation at up to 1 Mbps, low shutdown current down to 10 nA, and ±15 kV ESD protection on the serial-port connection pins. Its true RS-232 implementation supports systems that require bipolar line-level signaling rather than a non-RS-232 logic interface. Internally, the charge-pump circuit generates the positive and negative voltages required by the drivers. The receiver section converts the bipolar RS-232 signal into a CMOS-compatible logic level, while the driver section converts CMOS logic into RS-232 levels. This integration eliminates separate level-shifting circuitry and reduces the number of external support components required around a communications controller. Typical uses include industrial serial-control links, data-acquisition equipment, point-of-sale terminals, test and measurement instruments, and embedded systems that retain an RS-232 port. The ±15 kV protection rating is particularly relevant when the connector is exposed to electrostatic discharge or electrically noisy environments. PCB design should place the charge-pump capacitors and the external receiver and driver bypass capacitance close to their associated pins. Keep the exposed-pad ground connection and high-current return paths compact to minimize switching-current loops. Confirm the exact connector-side protection and grounding strategy against the MAX3232E data sheet before field deployment. This product overview combines the manufacturer’s electrical specifications, package information, cross-reference findings, application guidance, and practical layout considerations. It also distinguishes genuine same-footprint ordering options from RS-232 devices that require a different PCB footprint, helping engineers select a replacement without overlooking mechanical constraints.

RFQ Contact
MAX3232EETE+T - 3V to 5.5V, 1Mbps RS-232 | Analog Devices
MAX3232EETE+T

MAX3232EETE+T - 3V to 5.5V, 1Mbps RS-232 | Analog Devices

Analog Devices MAX3232EETE+T is a dual-channel true RS-232 transceiver with two drivers, two receivers, a 3.0V to 5.5V supply range, operation up to 1Mbps, and ±15kV IEC ESD protection, housed in a 16-pin TQFN package with an exposed pad. The MAX3232E family also supports shutdown current down to 10nA, making it suitable for power-constrained serial-interface systems. A true RS-232 transceiver is an interface IC that translates logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into digital logic levels. In the product hierarchy, the MAX3232EETE+T is a dual RS-232 transceiver, an RS-232 interface IC, a line-driver and receiver device, and a power-management-aware interface component. Its integrated dual charge pump generates the bipolar voltage required by RS-232 transmitters without a separate negative supply. The principal features are low-power operation, ±15kV ESD protection, true RS-232 compliance, and a 3.0V to 5.5V operating range. Two transmit channels and two receive channels support full-duplex serial links. A shutdown function reduces supply demand to as little as 10nA, while the Analog Devices MAX3232E product page identifies production availability and operation up to 1Mbps for this family. Internally, the device combines two line drivers, two line receivers, and a dual charge-pump circuit. The charge-pump design supports true RS-232 signal levels while operating from a single positive supply. According to the Analog Devices MAX3232E datasheet, the MAX3232E is pin, package, and functionally compatible with the industry-standard MAX232, giving designers a familiar interface arrangement when moving between suitable implementations. Typical uses include industrial serial-port controllers, USB-to-RS-232 adapters, embedded data acquisition systems, POS terminals, instrumentation, and legacy peripheral connectivity. The device is especially useful when both bidirectional communication and low standby consumption are required in a compact surface-mount design. PCB design should keep charge-pump capacitors and connector-side ESD protection close to their associated pins. Because a TQFN exposed pad requires careful thermal and layout treatment, follow the manufacturer's land pattern and thermal-via guidance rather than treating the pad as an optional connection. This product summary combines manufacturer specifications, ordering information, package details, and application-focused engineering guidance with a compatibility comparison for engineers evaluating RS-232 transceivers for industrial, embedded, and low-power serial-interface designs.

RFQ Contact
MAX3232EEUE+T - 1Mbps ESD RS-232 Transceiver | Analog Devices
MAX3232EEUE+T

MAX3232EEUE+T - 1Mbps ESD RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUE+T is a dual-driver, dual-receiver RS-232 transceiver operating from a 3.0 V to 5.5 V supply, with data rates up to 1 Mbps and ±15 kV ESD protection on the serial-port connections. The device is housed in a 16-pin TSSOP package and is supplied in the +T tape-and-reel configuration. It combines a true RS-232 interface with low-power charge-pump operation and low-power shutdown for portable and industrial serial equipment. An RS-232 transceiver is an interface IC that converts logic-level signals from a UART, microcontroller, or embedded controller into RS-232 line levels and converts received RS-232 signals back into logic levels. The MAX3232 belongs to the RS-232 interface hierarchy, which includes transceiver, line-driver, and line-receiver functions used to bridge modern digital logic with legacy serial-port equipment. The MAX3232EEUE+T provides two transmit channels and two receive channels in one package. Its 3.0 V to 5.5 V operating range supports both 3.3 V and 5 V systems, while its capability of 1 Mbps exceeds the 250 kbps rate stated for the Texas Instruments MAX3232E interface family. ±15 kV ESD protection improves robustness at externally accessible serial connectors, and the device supports low-power operation for battery-powered instruments. Internally, a dual charge-pump circuit generates the positive and negative voltage levels required by true RS-232 transmitters. The MAX3232 family uses four small external 0.1 µF capacitors, reducing board area compared with implementations requiring larger bulk capacitors. The MAX3232E family is also described by the manufacturer as pin-, package-, and functionally compatible with the industry-standard MAX232, subject to the exact package and ordering variant selected. Typical applications include industrial control links, point-of-sale equipment, data-acquisition systems, instrumentation, embedded service interfaces, and legacy peripheral connections. The two-driver, two-receiver configuration is particularly useful for bidirectional console links where one side transmits while the other receives, including designs that require loopback or crossed TX-to-RX connections. For PCB implementation, place the four 0.1 µF charge-pump capacitors close to their designated pins and route each TX and RX trace away from sensitive analog circuitry. Confirm the connector-side transient protection and grounding strategy because the internal ±15 kV ESD rating does not replace a correctly designed external protection network for every cable length or installation environment. This product guide combines the manufacturer specifications with package-level implementation guidance, application-specific use cases, and a same-footprint comparison of relevant RS-232 transceivers. It also identifies the electrical and qualification details that should be checked before replacing an existing MAX3232E design.

RFQ Contact
MAX3232EEUP+ 3V RS-232 Transceiver | Analog Devices
MAX3232EEUP+

MAX3232EEUP+ 3V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUP+ is a true RS-232 transceiver integrated circuit operating from 3.0V to 5.5V, with data rates up to 1Mbps and ±15kV ESD protection on the serial-port connections. The device combines two line drivers and two line receivers with integrated charge-pump circuitry, providing a compact interface between a digital controller and an RS-232 connector. An RS-232 transceiver is a semiconductor interface device that converts logic-level signals into RS-232 electrical levels and converts received RS-232 levels back into logic signals. The MAX3232EEUP+ belongs to the RS-232 interface IC and communication-interface hierarchy, making it suitable for embedded systems, industrial control equipment, instrumentation, and legacy serial communications. The main electrical characteristics are a 3.0V to 5.5V supply range, operation up to 1Mbps, ±15kV ESD protection, and operation with supply current down to 10nA as identified by the manufacturer’s product information. The integrated charge-pump design eliminates the need for an external RS-232 line driver in typical point-to-point serial links. The MAX3232EEUP+ is specified for low-power operation and true RS-232 signal levels. Its receiver and driver arrangement supports two transmit channels and two receive channels, allowing one IC to handle a bidirectional RS-232 interface when the system uses separate driver and receiver connections. The TSSOP-20 package supports compact surface-mount PCB layouts and automated assembly. Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale systems, service interfaces, and communication links to legacy RS-232 peripherals. In these systems, the MAX3232EEUP+ provides the electrical interface between a low-voltage controller and an external connector while adding ESD protection for exposed serial lines. Designers should verify connector pin assignments, line-driver and line-receiver polarity, external charge-pump capacitor values, and interface timing against the manufacturer datasheet. The device must also be checked against the required RS-232 voltage levels, cable length, data rate, and system grounding arrangement. This page combines the manufacturer product description, distributor listings, packaging information, and practical interface-design guidance to support component selection and RS-232 implementation planning.

RFQ Contact
MAX3232EEUP+G071 - 3-5.5V 250kbps RS-232 Transceiver | Analog Devices
MAX3232EEUP+G071

MAX3232EEUP+G071 - 3-5.5V 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUP+G071 is a dual-transmitter, dual-receiver RS-232 interface transceiver with a 3 V to 5.5 V supply range, data rates up to 250 kbps, and a 20-pin TSSOP package. It adds integrated charge-pump voltage conversion for reliable RS-232 signal generation while operating from a modern low-voltage digital supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts incoming RS-232 signals back into logic levels. The MAX3232E belongs to the broader interface transceiver hierarchy, combining line-driver and line-receiver functions in one package. This makes it suitable for equipment that must communicate with legacy serial ports, industrial controllers, barcode equipment, and computer peripherals. The MAX3232EEUP+G071 provides two transmitters and two receivers in a 20-pin TSSOP package. Its 3 V to 5.5 V operating range permits use with 3.3 V and 5 V systems, while the 250 kbps data rate covers standard asynchronous RS-232 links. The MAX3232E family also includes enhanced ESD protection, with a 15 kV rating identified for the family, helping reduce damage from electrostatic discharge encountered during handling or connection to external cables. The device uses on-chip charge-pump circuitry to generate the positive and negative voltage levels required by RS-232. This eliminates the need for a separate bipolar power supply in many designs. The transmitters invert the outgoing logic, and the receivers convert the bipolar RS-232 input into a compatible CMOS/TTL signal. MAX3232E-family devices are designed to remain interoperable with other RS-232 implementations when the same supply, data-rate, and connector standards are observed. Typical uses include industrial serial controllers, point-of-sale equipment, test fixtures, instrumentation, data acquisition units, and embedded systems that retain an RS-232 port. The 20-pin TSSOP package is also convenient for compact industrial control boards where a through-hole SOIC footprint is undesirable. Its interface function is especially useful when an existing system uses a 3.3 V processor but must retain an RS-232 connection to older peripheral equipment. PCB layout should keep the charge-pump and interface capacitors close to their associated pins, and external protection or filtering should be considered for long or exposed cables. The RS-232 ground and signal conductors should be routed as an interface pair, while high-current digital and switching power paths should remain separated to reduce ground disturbance. Confirm the complete pin assignments and recommended capacitor values in the manufacturer datasheet before releasing the PCB. This page combines the key MAX3232EEUP+G071 specifications, drop-in interface alternatives, package-level comparisons, and practical RS-232 layout guidance. It is intended to help engineers identify whether the part fits an existing 20-pin TSSOP design before sourcing, schematic capture, and prototype assembly.

RFQ Contact
MAX3232EEUP+G1Z - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEUP+G1Z

MAX3232EEUP+G1Z - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUP+G1Z is a true RS-232 transceiver with two drivers and two receivers, ±15 kV ESD protection, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps in a 20-pin TSSOP package. It converts TTL/CMOS logic levels to and from RS-232 differential signals, making it suitable for industrial control, data acquisition, instrumentation, and legacy peripheral connections. An RS-232 transceiver is an interface IC that bridges the logic-voltage domain of a digital system and the bipolar signal domain used by RS-232 equipment. It combines line drivers, receivers, charge-pump support circuitry, and ESD protection into one device. The MAX3232 belongs to the broader interface IC hierarchy, where it functions as a physical-layer communications component between embedded controllers and an external RS-232 port. The device provides true RS-232 output levels rather than limited-voltage RS-232 signaling. Its ±15 kV ESD protection helps protect the transceiver pins when a cable is connected or disconnected. Operation from 3.0 V to 5.5 V allows use in both 3.3 V and 5 V systems, while the maximum data rate of 1 Mbps supports communication rates substantially above common legacy serial-port operating speeds. The low-power design is specified for supply current down to 10 nA under applicable low-power conditions. The MAX3232 family uses integrated charge-pump circuitry to generate the positive and negative voltage rails needed by true RS-232 drivers. Four external capacitors support this operation, while the IC handles signal conditioning and level translation. Its two-driver, two-receiver arrangement suits point-to-point links in which each endpoint can transmit and receive. Because the +G1Z ordering code identifies a specific package and production configuration, engineers should verify the ordering information, tape orientation, and lead-free status before releasing a production order. Typical uses include programmable-logic-controller serial links, industrial equipment interfaces, test and measurement instruments, barcode readers, security equipment, and embedded control systems. A controller can connect its logic-level UART pins to the MAX3232EEUP+G1Z and communicate through a standard DE-9 connector. Cable length, baud rate, grounding, termination, and connector shield design remain system-level considerations even when the IC supports rates up to 1 Mbps. Place the charge-pump capacitors close to their associated pins and route the RS-232 traces away from sensitive analog or high-speed digital circuits. Provide a stable ground reference between the two connected systems, and use appropriate transient protection for cables exposed to industrial or outdoor environments. This page combines interface-family positioning, pin-compatible alternatives, and application-oriented design guidance to support component selection and board planning.

RFQ Contact
MAX3232EEUP+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEUP+T

MAX3232EEUP+T - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUP+T is a 2/2 full-duplex RS-232 transceiver with two drivers and two receivers, operating from 3.0 V to 5.5 V at data rates up to 1 Mbps in a 20-pin TSSOP package. It provides ±15 kV ESD protection on the serial-port pins and supports low-power operation with supply current as low as 10 nA in the specified shutdown condition. An RS-232 transceiver is an interface IC that converts logic-level signals from a UART or other asynchronous controller into RS-232 voltage levels, while receivers convert incoming RS-232 signals back into logic-compatible levels. In the electronic-component hierarchy, the MAX3232EEUP+T belongs to the interface IC class and uses a charge-pump voltage converter to generate the bipolar voltages required by true RS-232 links. Key features include a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, 2/2 transceiver configuration, and ±15 kV ESD protection. The integrated dual charge-pump circuit supports true RS-232 output levels while allowing the device to operate from a single low-voltage supply. Four external 0.1 µF charge-pump capacitors are specified by the MAX3232E documentation. The MAX3232E family is designed for asynchronous serial communication and complies with the electrical requirements of TIA/EIA-232-F. Pin, package, and functional compatibility with the industry-standard MAX232 is identified by Analog Devices. The MAX3232EEUP+T ordering code denotes the 20-pin TSSOP configuration with tape-and-reel production packaging. Typical uses include RS-232 ports on industrial-control equipment, data acquisition systems, instrumentation, service interfaces, and embedded serial adapters. Its 1 Mbps capability suits higher-speed legacy serial links, while the 3.0 V to 5.5 V operating range simplifies integration with modern 3.3 V and 5 V digital systems. PCB implementation requires close placement of the charge-pump capacitors and careful routing of the RS-232 driver outputs and receiver inputs. The external capacitor network should follow the manufacturer reference layout, while exposed interface connectors and cable routing require additional ESD and EMI design consideration to preserve reliable communication. This page combines the manufacturer family specifications with package, ordering, interface, and replacement information. It also provides application guidance and a comparison framework for engineers evaluating equivalent RS-232 transceivers for an existing TSSOP-20 design.

RFQ Contact
MAX3232EEUP+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEUP+TG1Z

MAX3232EEUP+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEUP+TG1Z is a dual-driver, dual-receiver RS-232 transceiver with operation from 3.0V to 5.5V, data rates up to 1Mbps, and 15kV ESD protection in a 20-pin TSSOP package. It also features low-power operation with supply current down to 10nA. An RS-232 transceiver is an interface IC that converts between complementary logic-level signals and the voltage-defined signaling used by RS-232 equipment. The MAX3232EEUP+TG1Z belongs to the RS-232 transceiver class within interface ICs and semiconductor signal-conditioning products. Its integrated level conversion allows a low-voltage digital system to communicate with legacy serial peripherals, industrial controllers, and computer equipment without external line-driver circuitry. The device provides two transmit channels and two receive channels, supporting full-duplex point-to-point links when both directions are required. Operation across a 3.0V to 5.5V supply range allows it to interface with 3.3V and 5V digital logic systems. The 1Mbps maximum data rate supports modern high-speed serial links, while 15kV ESD protection strengthens the interface against electrostatic discharge encountered in industrial and commercial environments. The MAX3232E family uses an on-chip charge-pump circuit to generate the positive and negative voltage levels required by RS-232 transmitters. This architecture permits true RS-232 operation from a single low-voltage supply. The manufacturer identifies the MAX3232E as pin, package, and functionally compatible with the industry-standard MAX232, while also providing low-power characteristics suited to portable and power-conscious equipment. Typical applications include industrial serial adapters, data-acquisition equipment, test and measurement instruments, point-of-sale terminals, and control systems that exchange data with RS-232 devices. The 20-pin TSSOP package supports compact surface-mount construction, although correct charge-pump capacitor placement and controlled RS-232 signal routing remain essential for reliable operation. For PCB design, place the external charge-pump capacitors close to their associated pins and keep RS-232 driver traces away from sensitive logic or analog nets. Confirm logic thresholds and signal direction before connecting external equipment because the transceiver's TTL-side inputs and outputs do not provide galvanic isolation. Confirm electrostatic requirements against the application's enclosure, grounding, and cable environment. This page combines manufacturer compatibility information, structured technical specifications, practical application guidance, and same-package replacement analysis to support faster component selection and PCB-level replacement decisions.

RFQ Contact
MAX3232EEWE+ - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+

MAX3232EEWE+ - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEWE+ is a dual-driver, dual-receiver RS-232 transceiver operating from 3.0V to 5.5V, supporting data rates up to 1Mbps in a 16-pin SOIC package. The device provides ±15kV ESD protection and a low-power design with shutdown current down to 10nA. It is a production-status, true RS-232 interface suitable for industrial control, instrumentation, data acquisition, and embedded serial communication systems. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-level signals. The MAX3232 belongs to the RS-232 transceiver family within interface ICs, where the dual-driver and dual-receiver arrangement provides two complete point-to-point serial channels. Its charge-pump-assisted implementation supports both 3.0V and 5.5V systems without requiring a negative supply. Key features include operation across a 3.0V to 5.5V supply range, data rates up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. Two transmitters and two receivers allow simultaneous bidirectional communication on separate RS-232 links. The 16-pin SOIC package supports conventional surface-mount PCB assembly, while the manufacturer designates the MAX3232 family as production and provides the associated data sheet with a revision number of 10. The MAX3232EEWE+ is identified as a full-duplex, 2/2 RS-232 transceiver. Its integrated charge-pump circuitry generates the voltage levels required by true RS-232, while the receiver side restores usable logic levels for the host controller. This combination allows a microcontroller, programmable logic controller, or UART-equipped processor to communicate with legacy RS-232 equipment through a compact two-channel interface. Typical uses include factory automation equipment, industrial sensors, barcode and test instruments, serial adapters, and embedded control boards. The 1Mbps capability is useful when a system needs more link bandwidth than conventional low-speed serial interfaces provide. The ±15kV ESD rating adds protection at connector-facing pins, although board-level grounding, shielding, and signal-routing practices remain necessary in electrically noisy installations. Designers should follow the manufacturer pin-description table when assigning connector and logic signals, and should place required charge-pump and bypass capacitors close to their designated pins. The unused driver output or receiver input should be handled according to the manufacturer guidance so that an unused channel does not float. Keep the RS-232 traces away from sensitive analog nodes and route chassis and signal-ground connections according to the system grounding strategy. This page combines the manufacturer's device identification with practical interface guidance, package details, sourcing information, and drop-in alternatives. It is intended to help engineers evaluate the MAX3232EEWE+ for a new RS-232 design or identify a compatible substitute for an existing 16-pin SOIC assembly.

RFQ Contact
MAX3232EEWE+G1Z - 2/2 RS-232 Transceiver | Analog Devices
MAX3232EEWE+G1Z

MAX3232EEWE+G1Z - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+G1Z is a 2/2 true RS-232 transceiver with two drivers and two receivers, operating from 3.0V to 5.5V and supporting data rates up to 1Mbps. The device is housed in a 16-pin SOIC package and provides ±15kV ESD protection on its RS-232 interface pins. Its low-power design operates down to 10nA, making it suitable for low-power serial equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible signals. The MAX3232EEWE+G1Z belongs to the transceiver class of interface ICs, combining two transmit channels and two receive channels in one package. This integrated arrangement reduces board area and simplifies design of point-to-point serial links, industrial control equipment, data-acquisition systems, and service interfaces. Key features include a 3.0V to 5.5V supply range, operation at up to 1Mbps, ±15kV ESD protection, and a low-power specification extending down to 10nA. The 2/2 channel arrangement allows two serial links to be implemented with one package. Its true RS-232 implementation is intended for systems whose connected equipment uses unbalanced RS-232 signaling rather than differential RS-485 or RS-422. The transceiver translates between modern CMOS logic levels and the voltage levels used by RS-232 equipment. Because RS-232 uses positive and negative signal voltages, the interface requires appropriate charge-pump circuitry and external charge-pump capacitors. The Analog Devices datasheet provides the recommended capacitor values, electrical characteristics, timing information, and pin configuration needed to design the interface correctly. Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale terminals, data loggers, instrument interfaces, and embedded systems communicating with legacy RS-232 peripherals. It is especially useful where two serial channels are required and a protected 16-pin SOIC footprint is preferable to larger transceiver packages. PCB layout should keep the charge-pump capacitor connections short, provide an uninterrupted ground path, and route RS-232 traces away from sensitive analog and high-speed digital circuits. External protection or filtering may be needed when cables are long, ports are frequently disconnected, or the interface is exposed to severe industrial transients. This product page combines the manufacturer interface information with practical selection, layout, and replacement guidance. It also distinguishes the verified electrical characteristics from parameters that require confirmation in the MAX3232E datasheet, helping engineers shorten component qualification without overlooking package and ordering-code differences.

RFQ Contact
MAX3232EEWE+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+T

MAX3232EEWE+T - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+T is a dual-channel true RS-232 transceiver with one driver and one receiver per channel, supporting data rates up to 1Mbps. It operates from 3.0V to 5.5V, features ±15kV ESD protection, and provides a shutdown supply current as low as 10nA. The device is packaged in a 16-pin wide SOIC and supplied on tape and reel with the +T ordering suffix. A true RS-232 transceiver is an interface circuit that converts logic-level signals between a host or embedded controller and an RS-232 link. The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by true RS-232, while integrated level translation allows the logic-side interface to operate from a low-voltage supply. This makes the device useful at the boundary between modern microcontrollers, industrial controllers, and legacy serial equipment. Key features include a 3.0V to 5.5V operating range, operation up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. Each channel includes a driver and receiver, allowing two communication paths in one package. The 16-pin wide SOIC footprint supports conventional surface-mount assembly and thermal design without requiring a high-pin-count package. The MAX3232E architecture is intended for systems where a compact true RS-232 interface, low standby consumption, and higher data-rate capability are important. Its 1Mbps maximum rate exceeds the common 250kbps operating point of many older RS-232 transceivers, while the 3.0V minimum supply supports direct operation from modern 3.3V system rails. The ±15kV protection rating improves robustness when exposed cables connect to exposed equipment or industrial control ports. Typical uses include industrial serial controllers, instrumentation, data-acquisition equipment, point-of-sale terminals, and embedded systems that need to connect to an RS-232 host. It is also appropriate for configuration and service ports in communications equipment. When paired with a microcontroller UART, the transceiver can provide bidirectional serial connectivity without implementing the RS-232 voltage levels externally. PCB design should place the charge-pump capacitors and bypass capacitors close to their specified pins. Keep the logic-side and RS-232-side routing paths separated to reduce coupling between fast switching nodes and sensitive receiver inputs. Follow the Analog Devices MAX3232E data sheet for the exact capacitor values, pin assignment, and layout pattern rather than substituting generic RS-232 layouts. This page combines manufacturer specifications, exact-ordering information, compatible alternatives, application guidance, and design notes to support component selection and PCB implementation. It is intended to answer practical engineering questions about voltage compatibility, data rate, ESD protection, pin compatibility, and replacement decisions.

RFQ Contact
MAX3232EEWE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+TG1Z

MAX3232EEWE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+TG1Z is a dual transmitter and dual receiver RS-232 interface IC operating from a 3.0V to 5.5V supply. It supports data rates up to 1Mbps, provides ±15kV ESD protection, and is offered in a 16-SOIC package. The device is designed for bidirectional serial data links that require true RS-232 signal levels rather than logic-level UART connections. An RS-232 transceiver is an interface IC within the broader communications-interface and semiconductor hierarchy. Its transmitters convert logic-level UART signals into RS-232 voltage levels, while its receivers convert incoming RS-232 signals back into logic-compatible levels. This allows equipment with different logic voltage domains to communicate across a wired serial interface while adding the electrical characteristics required by RS-232. The MAX3232EEWE+TG1Z provides two transmit channels and two receive channels, a maximum data rate of 1Mbps, and an operating supply range of 3.0V to 5.5V. Its ±15kV ESD protection improves tolerance of electrostatic discharge at connector-facing pins. The low-power design is specified with supply current down to 10nA, making it suitable for systems that need a low-overhead serial interface. The MAX3232 family uses integrated level-shaping circuitry to generate the bipolar voltage levels expected by RS-232 links from a single low-voltage supply. Designers still need to observe the recommended charge-pump capacitor values, connect supply and ground properly, and account for the voltage and current limitations of the RS-232 interface. The manufacturer states that MAX3232E devices are pin, package, and functionally compatible with the industry-standard MAX232, subject to verification of the exact ordering variant. Typical uses include industrial serial consoles, data-acquisition equipment, point-of-sale systems, instrumentation, embedded-control links, and service interfaces. The 16-SOIC package is also convenient for repairs and redesigns of legacy RS-232 equipment because the family maintains compatibility with established MAX232-class interfaces. When designing around this IC, confirm that the host UART uses the correct logic voltage and that the RS-232 cable is connected with the proper signal-to-ground relationship. Place the charge-pump capacitors and bypass capacitance close to their assigned pins, and keep connector protection and chassis-ground strategy separate from the sensitive receiver path. This product page consolidates electrical characteristics, package information, documented drop-in alternatives, and application-focused design guidance. It also distinguishes verified ordering variants from broader MAX3232-family options so engineers can assess PCB reuse, channel count, temperature grade, and lifecycle requirements before approving a substitution.

RFQ Contact
MAX3232EID - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EID

MAX3232EID - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EID is a dual-channel RS-232 line driver and receiver transceiver rated for 250 kbps, operating from a 3 V to 5.5 V supply and providing ±15 kV ESD protection. It is packaged in a 16-pin SOIC package. The device is intended for portable and industrial equipment that converts logic-level UART signals into RS-232 levels and converts received RS-232 signals back to logic levels. An RS-232 transceiver is an interface IC within the broader class of interface semiconductors. It combines a line driver, line receiver, and charge-pump voltage converter in one package. The MAX3232EID provides two driver and two receiver channels, allowing two simultaneous RS-232 links or one bidirectional port when the driver and receiver channels are paired. Its single 3 V to 5.5 V supply simplifies integration with modern 3.3 V and 5 V digital systems. The principal features include two RS-232 drivers, two RS-232 receivers, a maximum signaling rate of 250 kbps, and ESD protection to ±15 kV on the serial-port connection pins. According to the Texas Instruments MAX3232 product page, the MAX3232 family is recommended for new designs. The MAX3232E is an improved direct drop-in replacement for the original MAX3232, while the MAX3232EID suffix identifies the specified device ordering configuration. Internally, the charge-pump circuit develops the positive and negative voltage levels required by the RS-232 signaling standard. Transmit drivers convert CMOS/TTL-compatible input signals to RS-232 levels, while receive channels detect bipolar RS-232 inputs and produce CMOS/TTL-compatible outputs. The architecture makes this device appropriate for equipment with a host UART, an embedded controller, or an industrial data-acquisition system that must communicate with a legacy serial port. Typical uses include barcode scanners, instrumentation, industrial control links, point-of-sale equipment, and service-console connections. The 250 kbps maximum data rate supports conventional serial communication while the ±15 kV ESD rating helps protect exposed connector inputs. In battery-powered or space-constrained equipment, its single-supply operation can simplify voltage planning and reduce the number of external rails. When laying out the circuit, place charge-pump capacitors and the charge-pump flyback capacitor close to their associated device pins, and route RS-232 connector traces away from sensitive analog and high-speed digital paths. Confirm that the selected transceiver supports the baud rate, cable length, logic levels, and connector protection required by the target RS-232 environment. The IC-level ESD rating does not replace correct signal routing and appropriate external protection. This page combines the device specifications, sourcing workflow, family-level alternatives, and application guidance into a practical engineering resource. It also distinguishes verified device characteristics from package-ordering details and highlights the checks needed when evaluating a pin-compatible replacement for an existing MAX3232EID design.

RFQ Contact
MAX3232EIDB - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EIDB

MAX3232EIDB - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDB is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data-signaling rates up to 250 kbit/s. The device is housed in a 16-pin SSOP package and provides ±15 kV IEC ESD protection on the serial-port connection pins. It interfaces a host UART or asynchronous controller with an RS-232 connector while the integrated dual charge pump supplies the required bipolar line voltage. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDB is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART. Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables. The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered. Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins. For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing. This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.

RFQ Contact
MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments
MAX3232EIDBE4

MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDBE4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with two drivers, two receivers, and ±15 kV IEC ESD protection, housed in a 16-SSOP package. It supports the RS-232 interface for industrial-control, communications, and embedded systems while operating across the extended temperature range of −40°C to +85°C. An RS-232 transceiver is an interface IC that combines differential signal generation and reception for serial communications. It belongs to the line-driver/receiver hierarchy within interface ICs, bridging a host UART or processor logic-level port and a wired RS-232 connection. The MAX3232EIDBE4 is intended for designs that need both transmit and receive functions on one compact, surface-mount device. Key features include a 3 V to 5.5 V supply range, a 2/2 driver-and-receiver configuration, and bus-pin ESD protection rated to ±15 kV using the IEC 61000-4-2 contact-discharge and air-gap-discharge protection referenced in the product description. The 16-SSOP package measures approximately 5.30 mm in width and 0.209 inch in body width. The part is packaged in a tube according to the product listing. The E designation identifies the enhanced MAX3232E family, which Texas Instruments describes as an improved direct drop-in replacement for the original MAX3232. Its integrated charge-pump circuitry supports level translation between low-voltage digital logic and RS-232 signal levels without requiring a separate ±12 V supply. This simplifies interface implementation while retaining the voltage ranges and peripheral arrangement expected in MAX3232-class designs. Typical applications include RS-232 connections between embedded controllers and test equipment, industrial serial consoles, point-of-sale terminals, instrumentation, and legacy peripheral adapters. The two-driver and two-receiver arrangement supports full-duplex point-to-point links, provided the system designer accounts for the directional nature of each channel and applies appropriate interface protection where cables leave an enclosure. When designing a board around the MAX3232EIDBE4, preserve the manufacturer-recommended charge-pump capacitor connections and place the associated ceramic capacitors close to their pins. Confirm that the external connector, cable, and grounding strategy match the intended RS-232 application, because the integrated IC protects its bus pins but cannot compensate for an inadequate enclosure or cable shield. This page combines the device specifications, verified source links, package identification, application guidance, and confirmed same-package alternatives needed to evaluate the MAX3232EIDBE4. It also highlights where a replacement can be used without changing the 16-SSOP land pattern and where temperature, packing, or parameter differences still require engineering review.

RFQ Contact
MAX3232EIDBG4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232EIDBG4

MAX3232EIDBG4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDBG4 is a dual RS-232 line-driver and line-receiver transceiver with a 3 V to 5.5 V supply, two drivers, two receivers, and ±15 kV IEC ESD protection on the serial-port pins. It is packaged in a 16-pin SSOP and is designed to connect a modern low-voltage controller to an RS-232 serial-port connector. An RS-232 transceiver is an interface IC within the broader semiconductor and interface-controller hierarchy. It converts logic-level signals from an asynchronous communication controller into RS-232 line levels, while receiving and translating remote RS-232 signals back into logic levels. The MAX3232EIDBG4 supports both directions on one compact package, reducing board area compared with separate driver and receiver ICs. The device operates from 3 V to 5.5 V, so it can be powered directly from common 3.3 V or 5 V systems. Its two line drivers and two receivers suit point-to-point serial links, including industrial controllers, POS terminals, data-acquisition equipment, and service interfaces. The integrated dual charge-pump generates the positive and negative voltage levels required by RS-232 without a separate supply. The MAX3232E family is designed to meet TIA/EIA-232-F requirements. According to the manufacturer datasheet, the serial-port pins, including ground, provide ±15 kV IEC ESD protection pin to pin. This protection is valuable when cables connect the board to external equipment through uncontrolled connector environments. The improved MAX3232E is also described by Texas Instruments as a direct drop-in replacement for the original MAX3232. Typical uses include RS-232 adapters for embedded processors, configuration links on industrial automation equipment, instrument-control ports, and legacy peripheral connections. The 3 V to 5.5 V operating range makes the interface suitable for both 5 V industrial systems and modern 3.3 V controller platforms. Place the charge-pump capacitors and the interface bypass capacitor close to their designated pins, and route the exposed connector-side signals away from sensitive clock and analog traces. Confirm polarity and signal direction at the RS-232 connector because the logic-side and line-side pin functions are not interchangeable. This page organizes the electrical limits, package information, replacement options, comparison parameters, and practical layout guidance needed to evaluate the MAX3232EIDBG4 before integrating it into an RS-232 interface design.

RFQ Contact
MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232EIDBR

MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232EIDBR is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data-signaling rates up to 250 kbit/s. The device is housed in a 16-pin SSOP package and provides ±15 kV IEC ESD protection on the serial-port connection pins. It interfaces a host UART or asynchronous controller with an RS-232 connector while the integrated dual charge pump supplies the required bipolar line voltage. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDBR is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART. Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables. The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered. Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins. For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing. This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.

RFQ Contact
MAX3232EIDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232EIDR

MAX3232EIDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232EIDR is a dual-channel RS-232 line driver and receiver transceiver rated for 250 kbps, operating from a 3 V to 5.5 V supply and providing ±15 kV ESD protection. It is packaged in a 16-pin SOIC package. The device is intended for portable and industrial equipment that converts logic-level UART signals into RS-232 levels and converts received RS-232 signals back to logic levels. An RS-232 transceiver is an interface IC within the broader class of interface semiconductors. It combines a line driver, line receiver, and charge-pump voltage converter in one package. The MAX3232EIDR provides two driver and two receiver channels, allowing two simultaneous RS-232 links or one bidirectional port when the driver and receiver channels are paired. Its single 3 V to 5.5 V supply simplifies integration with modern 3.3 V and 5 V digital systems. The principal features include two RS-232 drivers, two RS-232 receivers, a maximum signaling rate of 250 kbps, and ESD protection to ±15 kV on the serial-port connection pins. According to the Texas Instruments MAX3232 product page, the MAX3232 family is recommended for new designs. The MAX3232E is an improved direct drop-in replacement for the original MAX3232, while the MAX3232EIDR suffix identifies the specified device ordering configuration. Internally, the charge-pump circuit develops the positive and negative voltage levels required by the RS-232 signaling standard. Transmit drivers convert CMOS/TTL-compatible input signals to RS-232 levels, while receive channels detect bipolar RS-232 inputs and produce CMOS/TTL-compatible outputs. The architecture makes this device appropriate for equipment with a host UART, an embedded controller, or an industrial data-acquisition system that must communicate with a legacy serial port. Typical uses include barcode scanners, instrumentation, industrial control links, point-of-sale equipment, and service-console connections. The 250 kbps maximum data rate supports conventional serial communication while the ±15 kV ESD rating helps protect exposed connector inputs. In battery-powered or space-constrained equipment, its single-supply operation can simplify voltage planning and reduce the number of external rails. When laying out the circuit, place charge-pump capacitors and the charge-pump flyback capacitor close to their associated device pins, and route RS-232 connector traces away from sensitive analog and high-speed digital paths. Confirm that the selected transceiver supports the baud rate, cable length, logic levels, and connector protection required by the target RS-232 environment. The IC-level ESD rating does not replace correct signal routing and appropriate external protection. This page combines the device specifications, sourcing workflow, family-level alternatives, and application guidance into a practical engineering resource. It also distinguishes verified device characteristics from package-ordering details and highlights the checks needed when evaluating a pin-compatible replacement for an existing MAX3232EIDR design.

RFQ Contact
MAX3232EIDWG4 - Dual RS-232 IC | Texas Instruments
MAX3232EIDWG4

MAX3232EIDWG4 - Dual RS-232 IC | Texas Instruments

The Texas Instruments MAX3232EIDWG4 is a dual-channel RS-232 line driver and receiver interface IC with a 3 V to 5.5 V supply range, ±15 kV IEC ESD protection, and a 16-pin SOIC package. It converts CMOS/TTL logic levels to RS-232 levels and converts incoming RS-232 signals back to logic levels. An RS-232 interface transceiver is a semiconductor that bridges the voltage-domain difference between digital logic and the bipolar RS-232 serial interface. The MAX3232EIDWG4 belongs to the interface IC hierarchy, where a transceiver integrates one or more line drivers and receivers with charge-pump circuitry and electrostatic-discharge protection. It is commonly placed between a microcontroller UART and an external serial connector. Key features include two driver and two receiver channels, operation from 3 V to 5.5 V, and ±15 kV IEC ESD protection. The E suffix identifies the enhanced ESD-capable family, while the G4 ordering code denotes the green, standard industrial-temperature version associated with a −40 °C to +85 °C operating range. The 16-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB production. The MAX3232E uses on-chip charge-pump circuitry to generate the positive and negative voltage swings required by RS-232 without a negative supply input. This architecture allows the logic side to operate from a single 3 V to 5.5 V rail. The interface includes integrated protection for external connector signals, reducing the need for separate low-capacitance TVS devices when the board layout and routing follow the manufacturer's recommendations. Typical applications include industrial serial controllers, test and measurement equipment, computer peripherals, point-of-sale terminals, embedded service ports, and legacy RS-232 equipment connected to modern microcontrollers. The dual-channel arrangement is useful when one system must support bidirectional communication, multiple RS-232 devices, or separate transmit and receive data paths. PCB design should place the device near the RS-232 connector, route driver outputs and receiver inputs away from sensitive logic, and connect the charge-pump capacitors and supply-decoupling capacitor close to their specified pins. Keep unprotected external leads short and follow the datasheet's ESD layout guidance so that system-level transient performance is not limited by long copper traces. This product page combines the exact ordering information, electrical limits, interface characteristics, package details, drop-in alternatives, comparison parameters, and practical PCB guidance needed to evaluate and implement the MAX3232EIDWG4 in a new design.

RFQ Contact
MAX3232EIPW - 250kbps RS-232 Transceiver | Texas Instruments
MAX3232EIPW

MAX3232EIPW - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIPW is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data rates up to 250 kbps, housed in a 16-pin TSSOP package. It provides two transmit channels, two receive channels, an integrated dual charge pump, and ±15 kV IEC ESD protection on the serial-port pins. An RS-232 transceiver is an interface IC that converts logic-level signals from a controller or microcontroller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible outputs. Within the broader hierarchy, the MAX3232EIPW is an RS-232 transceiver, serial-interface IC, interface IC, and semiconductor designed for asynchronous serial communications. The MAX3232E family operates without a separate 5 V-only supply, making it suitable for mixed-voltage systems with 3.3 V or 5 V logic. Its charge-pump circuitry develops the positive and negative voltages required by RS-232 from the single supply. The device supports 250 kbps operation and includes TIA/EIA-232-F-compatible electrical behavior according to the Texas Instruments product page. The integrated protection is a major functional distinction from older MAX3232 devices. The manufacturer identifies ±15 kV IEC ESD protection from pin to pin on the serial-port connections, including ground, while the MAX3232E remains a direct drop-in replacement for the original MAX3232. This makes it appropriate for exposed equipment, industrial interfaces, and systems where a disconnected cable may introduce electrostatic discharge. Typical uses include RS-232 ports on industrial controllers, test equipment, POS terminals, data acquisition units, service interfaces, and legacy peripherals that require a full-duplex serial connection. The device can also serve as the physical-layer interface between a 3.3 V microcontroller UART and an RS-232 connector. PCB design should place the charge-pump capacitors close to their associated pins and route the RS-232 connector nets away from sensitive analog or high-speed digital traces. The TSSOP-16 footprint permits a compact layout, but connector protection, grounding, and cable-retention requirements can dominate the available board area. Confirm signal polarity, flow-control assumptions, and the connector pin assignment before replacing an existing design. This product record combines the manufacturer's device capabilities, package information, interface requirements, drop-in alternatives, and practical PCB guidance. It also distinguishes the electrically enhanced MAX3232E from older non-E variants so engineers can make a compatibility decision based on protection and operating requirements rather than package similarity alone.

RFQ Contact