Products (44,000+)

MAX3232ECDBR - RS-232 Transceiver 3-5.5V ±15kV ESD | TI (Tape & Reel)
MAX3232ECDBR

MAX3232ECDBR - RS-232 Transceiver 3-5.5V ±15kV ESD | TI (Tape & Reel)

The Texas Instruments MAX3232ECDBR is a 2-driver, 2-receiver RS-232 line transceiver operating from a single 3V to 5.5V supply, with ±15 kV IEC ESD protection on the RS-232 bus pins, packaged in a 16-pin SSOP (DB, 5.30 mm width) for commercial 0C to +70C operation. An RS-232 transceiver is a line driver/receiver IC that converts logic-level UART signals (TTL/CMOS, 0V to VCC) into the higher-voltage RS-232 signaling levels (nominally ±5V or more) required by serial ports, modems, and industrial equipment. Within the interface IC family hierarchy, it sits alongside CAN, RS-485, and USB transceivers as a physical-layer signal-conditioning device in the broader category of communication interface components. Key features include guaranteed 250 kbps minimum data rate, a charge-pump architecture that generates the required RS-232 voltage levels using only four small 0.1 uF external capacitors, and ESD protection exceeding ±15 kV (IEC 61000-4-2 air-gap and contact discharge) plus ±15 kV human-body model on the bus terminals. The device meets or exceeds TIA/EIA-232-F requirements and operates from a single supply across the full 3.0V to 5.5V range, eliminating the need for dual ±12V rails. Technically, the MAX3232E family uses proprietary on-chip charge pumps with automatic internal voltage doubling and inversion to produce V+ and V- from the single VCC rail. Two transmitters and two receivers enable a full-duplex UART link with hardware flow control (RTS/CTS). Low receiver-enable current and a shutdown-capable architecture suit battery-powered designs. Typical applications include embedded MCU UART-to-RS-232 ports, industrial programmable logic controller (PLC) console interfaces, point-of-sale equipment, and networking equipment management ports. The E-version ESD rating makes it especially appropriate for ports exposed to human contact. Design consideration: place the four charge-pump capacitors close to pins 1-6 and use 0.1 uF ceramic parts rated at 16V or more; larger values (up to 1 uF) are acceptable but slow the pump startup slightly. This page synthesizes distributor pricing, pin-to-pin drop-in alternatives across TI and MaxLinear/Exar, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MAX3232ECDE4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3232ECDE4

MAX3232ECDE4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232ECDE4 is a dual RS-232 line driver and receiver integrated circuit with two transmit channels and two receive channels. It supports data rates up to 250 kbps from a 3 V to 5.5 V supply and provides ±15 kV IEC ESD protection on the RS-232 interfaces. The device is packaged in a 16-pin SOIC and is specified for a 0 °C to 70 °C ambient temperature range. An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 signals and complementary digital logic levels. It belongs to the transceiver class of interface ICs, combining a line driver, a line receiver, charge-pump voltage generation, and logic-level translation in one package. This integration reduces the component count required for serial ports in industrial controllers, test equipment, and embedded systems. Key features include full-duplex operation with two drivers and two receivers, a 250 kbps maximum signaling rate, and a wide 3 V to 5.5 V operating supply range. The ±15 kV IEC ESD rating is the primary distinction between the E-series MAX3232 devices and standard MAX3232C variants. The SOIC-16 package also supports automated assembly and compact board layouts that are difficult to achieve with larger through-hole transceivers. The MAX3232ECDE4 uses on-chip charge pumps to generate the positive and negative voltage levels required by the RS-232 drivers. Its receivers include Schmitt-trigger inputs, which improve noise immunity when the logic threshold lies near a switching transition. Both interfaces are designed for noisy industrial environments where cable transients and ESD events are common. Detailed electrical limits and timing margins must be confirmed against the manufacturer datasheet before release. Typical applications include RS-232 links between a host computer and an embedded controller, industrial instrumentation, programmable-logic equipment, service interfaces, and legacy peripheral connectivity. The device is especially useful where the logic system operates from 3.3 V or 5 V but the external cable interface must comply with RS-232 voltage levels. The 16-pin SOIC footprint is appropriate for designs that do not require electrical isolation. For layout, place the charge-pump capacitors close to their associated device pins and route the RS-232 driver and receiver connections directly to the connector or protection network. Keep logic-side traces away from exposed cable-side nets. Confirm the external charge-pump capacitor values and ESD protection network against the manufacturer application guidance before fabrication. This page organizes the verified device characteristics, practical RS-232 design considerations, pin-level package information, and drop-in replacement analysis. It helps engineers evaluate the MAX3232ECDE4 against lower-ESD MAX3232C variants and other 16-pin RS-232 transceivers without relying on fragmented distributor listings.

RFQ Contact
MAX3232ECDG4 - 2/2 RS-232 Transceiver | Texas Instruments
MAX3232ECDG4

MAX3232ECDG4 - 2/2 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232ECDG4 is a 2/2 multichannel RS-232 line driver and receiver with a 3 V to 5.5 V supply, 250 kbps data rate, and ±15 kV IEC ESD protection, housed in a 16-pin SOIC package. It provides two transmit channels and two receive channels for bidirectional serial-interface designs. An RS-232 transceiver is an interface IC that converts digital logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where it bridges computer or embedded systems with the physical RS-232 bus. Its dual-driver, dual-receiver arrangement supports point-to-point links and multi-drop receiver networks while reducing the number of external interface components. The MAX3232ECDG4 operates from 3 V to 5.5 V and is designed for 250 kbps RS-232 data rates. Its integrated charge-pump circuitry supports operation from a single supply, eliminating the need for a separate negative-voltage supply in the host design. The two drivers and two receivers support common applications involving serial ports, data acquisition, industrial control, and embedded equipment. Electrical protection is a major feature of this interface. According to the Texas Instruments datasheet, the RS-232 bus pins provide ±15 kV ESD protection under the IEC contact-discharge and air-discharge conditions. This protection helps improve system survivability when a connected cable exposes the interface to electrostatic discharge. The IC is specified for a 0 °C to 70 °C operating-temperature range. The MAX3232ECDG4 is used in industrial serial communication, test and measurement equipment, point-of-sale terminals, security systems, and embedded control systems. Its 16-pin SOIC package is suitable for conventional surface-mount assembly and PCB layouts that already use narrow SOIC-16 footprints. When designing around the MAX3232ECDG4, verify the RS-232 connector-side protection network and place it where it can intercept electrostatic discharge before the signal reaches the IC. Keep the high-current charge-pump and driver return paths compact, and follow the manufacturer’s capacitor recommendations to maintain stable operation. Confirm that cable routing, grounding, and logic levels satisfy the system interface specification. This page combines manufacturer specifications, verified distributor listings, package information, drop-in comparison options, and practical PCB guidance. It is intended to help engineers evaluate the MAX3232ECDG4 for new designs and to identify a compatible replacement only after checking the complete datasheet, pin configuration, package, and operating requirements.

RFQ Contact
MAX3232ECDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232ECDR

MAX3232ECDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232ECDR is a dual-channel RS-232 line driver and receiver operating from 3 V to 5.5 V, supporting data rates up to 250 kbps and providing ±15-kV IEC ESD protection on the RS-232 bus pins. The device is packaged in a 16-pin SOIC for compact, surface-mount serial-interface designs. An RS-232 transceiver is the physical-layer interface between a host controller or data-processing equipment and an RS-232 port. It combines a line driver, which converts logic-level signals into RS-232 voltage levels, with a receiver, which converts incoming RS-232 signals back into logic-compatible levels. In the power-management hierarchy of communication systems, the MAX3232ECDR provides bidirectional RS-232 signal conditioning between a UART controller and an external connector. Key operating features include two communication channels, a 3 V to 5.5 V supply range, and a maximum data rate of 250 kbps. The ±15-kV IEC ESD protection improves robustness when cables and connectors are exposed to electrostatic discharge. These characteristics make the device suitable for industrial control equipment, data acquisition systems, service interfaces, and legacy peripheral connections where a modern USB interface is not practical. The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 from a single low-voltage supply. This allows the transceiver to operate from 3 V to 5.5 V instead of requiring the traditional ±12 V RS-232 supply. The manufacturer identifies the MAX3232 as a dual-channel 250-kbps line driver and receiver, while its comparison materials identify the MAX3232E as an improved direct drop-in replacement for the MAX3232. Typical applications include UART-to-RS-232 conversion in industrial controllers, programming and configuration ports in test equipment, service interfaces for embedded systems, and point-to-point links between computers or controllers and RS-232 equipment. Using one transceiver supports two RS-232 channels, allowing transmit and receive signals to share the same physical interface without requiring separate driver and receiver packages. The primary design consideration is ensuring that external cable transients remain within the device's operating and protection limits. Keep RS-232 traces away from sensitive clocks and data lines, provide a low-impedance ground return, and use the device pin descriptions in the manufacturer datasheet when assigning PCB functions. Power-supply bypassing and charge-pump capacitor placement should follow the datasheet's recommended layout to maintain stable operation and minimize coupling into adjacent circuitry. This product page combines the MAX3232ECDR's electrical characteristics, package information, verified manufacturer resources, drop-in alternatives, comparison guidance, and practical interface-design notes. It is intended to help engineers confirm electrical compatibility, identify the correct 16-SOIC replacement, and plan PCB implementation before releasing a new RS-232 design.

RFQ Contact
MAX3232ECDW - 3-5.5V RS-232 Transceiver | Texas Instruments
MAX3232ECDW

MAX3232ECDW - 3-5.5V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232ECDW is a 3 V to 5.5 V RS-232 line-driver and receiver transceiver with two transmitters, two receivers, ±15 kV IEC ESD protection, and a 16-pin SOIC package. It provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts received RS-232 signals back into logic levels. It belongs to the hierarchy of serial-interface transceivers, communication interface ICs, and semiconductor interface devices. The MAX3232E family also integrates a dual charge pump, allowing operation from a single 3 V to 5.5 V supply without a separate negative supply rail. The device provides two RS-232 transmitters and two RS-232 receivers in a 16-pin SOIC package. Its operating supply range of 3 V to 5.5 V supports both 3.3 V and 5 V system environments. Pin-to-pin IEC ESD protection of ±15 kV applies to the serial-port connection pins, including ground, improving interface robustness in electrically noisy installations. According to the Texas Instruments MAX3232E product page, the MAX3232E meets TIA/EIA-232-F requirements. The integrated dual charge pump generates the positive and negative voltages required for RS-232 signaling while keeping the external power-supply requirement to a single positive rail. The interface separates external line-side signals from the logic-side circuitry used by UART and other asynchronous controllers. Typical uses include industrial serial adapters, barcode readers, test and measurement equipment, security consoles, and embedded systems that retain an RS-232 port. The device is particularly suitable when a modern 3.3 V controller must communicate with legacy RS-232 equipment through a compact, surface-mount interface. Its 16-pin SOIC package also simplifies assembly and inspection in designs that do not require an extended-voltage transceiver. Decoupling capacitor placement is critical to charge-pump performance. Follow the manufacturer datasheet when placing the charge-pump fly capacitors, supply bypass capacitor, and connector-side protection network. Keep the serial traces short, route them away from clocks and switching nodes, and provide a low-impedance ground return between the transceiver and connector. This page combines electrical specifications, pin-level guidance, drop-in cross-references, and application-focused design notes. It helps engineers distinguish the MAX3232ECDW from related MAX3232E and MAX3232C variants while preserving the same 16-pin SOIC board footprint during sourcing or redesign.

RFQ Contact
MAX3232ECDWG4 - 3 to 5.5V Dual RS-232 Transceiver | Texas Instruments
MAX3232ECDWG4

MAX3232ECDWG4 - 3 to 5.5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232ECDWG4 is a 3 V to 5.5 V RS-232 line transceiver with two transmitters, two receivers, a dual charge-pump circuit, and ±15 kV IEC ESD protection, packaged in a 16-pin SOIC. The MAX3232ECDWG4 provides the electrical interface between RS-232 ports and CMOS-compatible microcontroller or FPGA logic while supporting commercial-temperature operation. An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 signals and lower-voltage logic signals. The MAX3232ECDWG4 belongs to the RS-232 transceiver hierarchy, where it bridges a communications port on one side and a host controller on the other. Its integrated charge pumps generate the positive and negative voltages required to transmit RS-232 levels without a separate external supply. The device operates from 3 V to 5.5 V and includes two drivers and two receivers. Pin-to-pin ESD protection is rated at ±15 kV using the IEC contact-discharge and air-gap-discharge criteria identified for the MAX3232E family. Additional operating features include low-power operation, short-circuit protection, and compatibility with TIA/EIA-232-F interface requirements. Technically, the dual charge-pump architecture supports both RS-232 directions while reducing the external component count required for level translation. The transmitters convert CMOS logic into RS-232 signal levels, while the receivers detect and convert incoming RS-232 levels into CMOS-compatible signals. This integration is useful where a system needs reliable serial-console, point-to-point, or equipment-control connectivity without using a full UART physical-layer solution with additional external support circuitry. Typical applications include industrial serial adapters, instrumentation, data-acquisition equipment, embedded control panels, and debug or programming interfaces connected to microcontrollers and FPGAs. The 3 V to 5.5 V supply range allows operation alongside both 3.3 V and 5 V digital systems. Commercial temperature grade and tube packaging support conventional industrial and consumer manufacturing processes. For PCB design, place the charge-pump capacitors and the interface-side capacitors close to their associated pins, keep the RS-232 connector path away from sensitive clocks and analog inputs, and provide a low-impedance ground return between connected equipment. Cable transients still require system-level protection when exposed to severe industrial or outdoor environments. This page combines device specifications, practical PCB guidance, sourcing information, and a qualified drop-in comparison to help engineers evaluate the MAX3232ECDWG4 for new designs and controlled replacement programs.

RFQ Contact
MAX3232ECDWR - 3-5.5V RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232ECDWR

MAX3232ECDWR - 3-5.5V RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232ECDWR is a 3 V to 5.5 V RS-232 line-driver and receiver transceiver with two transmitters, two receivers, ±15 kV IEC ESD protection, and a 16-pin SOIC package. It provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts received RS-232 signals back into logic levels. It belongs to the hierarchy of serial-interface transceivers, communication interface ICs, and semiconductor interface devices. The MAX3232E family also integrates a dual charge pump, allowing operation from a single 3 V to 5.5 V supply without a separate negative supply rail. The device provides two RS-232 transmitters and two RS-232 receivers in a 16-pin SOIC package. Its operating supply range of 3 V to 5.5 V supports both 3.3 V and 5 V system environments. Pin-to-pin IEC ESD protection of ±15 kV applies to the serial-port connection pins, including ground, improving interface robustness in electrically noisy installations. According to the Texas Instruments MAX3232E product page, the MAX3232E meets TIA/EIA-232-F requirements. The integrated dual charge pump generates the positive and negative voltages required for RS-232 signaling while keeping the external power-supply requirement to a single positive rail. The interface separates external line-side signals from the logic-side circuitry used by UART and other asynchronous controllers. Typical uses include industrial serial adapters, barcode readers, test and measurement equipment, security consoles, and embedded systems that retain an RS-232 port. The device is particularly suitable when a modern 3.3 V controller must communicate with legacy RS-232 equipment through a compact, surface-mount interface. Its 16-pin SOIC package also simplifies assembly and inspection in designs that do not require an extended-voltage transceiver. Decoupling capacitor placement is critical to charge-pump performance. Follow the manufacturer datasheet when placing the charge-pump fly capacitors, supply bypass capacitor, and connector-side protection network. Keep the serial traces short, route them away from clocks and switching nodes, and provide a low-impedance ground return between the transceiver and connector. This page combines electrical specifications, pin-level guidance, drop-in cross-references, and application-focused design notes. It helps engineers distinguish the MAX3232ECDWR from related MAX3232E and MAX3232C variants while preserving the same 16-pin SOIC board footprint during sourcing or redesign.

RFQ Contact
MAX3232ECPE+ - ±15kV ESD RS-232 Transceiver | Analog Devices
MAX3232ECPE+

MAX3232ECPE+ - ±15kV ESD RS-232 Transceiver | Analog Devices

The MAX3232ECPE+ from Analog Devices is a dual RS-232 transceiver designed for low-voltage serial interfaces, with two transmit channels, two receive channels, and integrated charge-pump circuitry. It operates from a 3.0V to 5.5V supply, supports data rates up to 1Mbps, and is specified for ±15kV ESD protection on the RS-232 connection pins. The device is packaged in a 16-pin PDIP package. An RS-232 transceiver is an interface IC that translates logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back to logic levels. The MAX3232 belongs to the broader RS-232 interface family, supporting communication between modern microcontrollers, computers, industrial controllers, and legacy serial equipment. Its integrated charge pump generates the positive and negative voltage rails required by the RS-232 transmitter outputs. Key features include a 3.0V to 5.5V operating supply range, operation at data rates up to 1Mbps, low-power operation, and enhanced electrostatic-discharge protection. The MAX3232ECPE+ is identified as a true RS-232 transceiver, and the manufacturer describes the MAX3232 family as compatible with the MAX232 family in pin, package, and function for supported variants. The MAX3232ECPE+ is suitable for systems that need dual-channel RS-232 connectivity without using a higher-voltage supply for the interface. The internal charge-pump design allows the device to operate from a single low-voltage supply while producing the bipolar voltage levels expected by RS-232 receivers. The maximum specified data rate of 1Mbps supports high-speed asynchronous serial links where cable length, termination, and signal integrity are properly controlled. Typical applications include industrial control equipment, data acquisition systems, instrumentation, point-of-sale terminals, service interfaces, and embedded systems that communicate with RS-232 peripherals. The dual-driver and dual-receiver arrangement supports either two independent transmit paths, two independent receive paths, or a combination of full-duplex RS-232 links. PCB layout should keep the charge-pump capacitors and the RS-232 connector-side protection network close to the device. The DIP package is suitable for prototyping, legacy industrial equipment, and through-hole industrial control boards where a surface-mount package is not required. Before production use, verify the complete pin assignment, recommended capacitor values, ESD layout, and operating limits against the manufacturer datasheet.

RFQ Contact
MAX3232ECPW - Dual RS-232 Transceiver | Texas Instruments
MAX3232ECPW

MAX3232ECPW - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232ECPW is a dual-channel RS-232 line transceiver operating from a single 3 V to 5.5 V supply, supporting signal rates up to 250 kbit/s and providing ±15 kV IEC ESD protection. The device combines two line drivers, two line receivers, and a dual charge-pump circuit in a 16-pin TSSOP package. An RS-232 transceiver is an interface IC that converts logic-level signals from a processor or controller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible levels. Within the hierarchy of interface ICs, serial transceivers connect digital controllers to communication ports using the TIA/EIA-232-F electrical standard. The MAX3232ECPW uses an on-chip charge pump to generate positive and negative RS-232 voltages from one low-voltage supply. The device accepts supply voltages from 3 V to 5.5 V and operates at data-signaling rates up to 250 kbit/s. Its two transmitters and two receivers support full-duplex serial links, while driver output slew rate is limited to 30 V/µs. Pin-to-pin ESD protection rated at ±15 kV improves system robustness when cables are connected or disconnected. The MAX3232ECPW is the commercial-temperature version of the MAX3232E family, specified for 0 °C to 70 °C. It is packaged in a 16-pin gull-wing TSSOP with a 4.4 mm lead pitch. Four external charge-pump capacitors are required, allowing the interface to operate from a single 3 V or 5 V rail without a separate negative power supply. Typical uses include industrial serial adapters, data-acquisition equipment, point-of-sale terminals, laboratory instruments, and service-console links. The device is appropriate when a controller needs an RS-232 port but cannot generate the positive and negative voltages required by legacy RS-232 drivers directly. Place the four charge-pump capacitors close to their associated pins and keep the exposed supply and ground paths short. Keep the RS-232 connector interface physically separated from sensitive analog or high-speed digital routing, and provide appropriate board-level protection when exposed cables exceed the device's rated ESD withstand. This product page combines electrical specifications, package and pin information, drop-in replacement analysis, application guidance, and design notes for engineers evaluating the MAX3232ECPW in 3 V and 5 V RS-232 interfaces.

RFQ Contact
MAX3232ECPWR - Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232ECPWR

MAX3232ECPWR - Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232ECPWR is a dual-channel RS-232 line transceiver operating from a single 3 V to 5.5 V supply, supporting signal rates up to 250 kbit/s and providing ±15 kV IEC ESD protection. The device combines two line drivers, two line receivers, and a dual charge-pump circuit in a 16-pin TSSOP package. An RS-232 transceiver is an interface IC that converts logic-level signals from a processor or controller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible levels. Within the hierarchy of interface ICs, serial transceivers connect digital controllers to communication ports using the TIA/EIA-232-F electrical standard. The MAX3232ECPWR uses an on-chip charge pump to generate positive and negative RS-232 voltages from one low-voltage supply. The device accepts supply voltages from 3 V to 5.5 V and operates at data-signaling rates up to 250 kbit/s. Its two transmitters and two receivers support full-duplex serial links, while driver output slew rate is limited to 30 V/µs. Pin-to-pin ESD protection rated at ±15 kV improves system robustness when cables are connected or disconnected. The MAX3232ECPWR is the commercial-temperature version of the MAX3232E family, specified for 0 °C to 70 °C. It is packaged in a 16-pin gull-wing TSSOP with a 4.4 mm lead pitch. Four external charge-pump capacitors are required, allowing the interface to operate from a single 3 V or 5 V rail without a separate negative power supply. Typical uses include industrial serial adapters, data-acquisition equipment, point-of-sale terminals, laboratory instruments, and service-console links. The device is appropriate when a controller needs an RS-232 port but cannot generate the positive and negative voltages required by legacy RS-232 drivers directly. Place the four charge-pump capacitors close to their associated pins and keep the exposed supply and ground paths short. Keep the RS-232 connector interface physically separated from sensitive analog or high-speed digital routing, and provide appropriate board-level protection when exposed cables exceed the device's rated ESD withstand. This product page combines electrical specifications, package and pin information, drop-in replacement analysis, application guidance, and design notes for engineers evaluating the MAX3232ECPWR in 3 V and 5 V RS-232 interfaces.

RFQ Contact
MAX3232ECSE+ - Dual RS-232 Transceiver | Analog Devices
MAX3232ECSE+

MAX3232ECSE+ - Dual RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECSE+ is a dual RS-232 transceiver with two line drivers, two line receivers, and a dual charge-pump supply in a 16-SOIC package. It operates from 3.0 V to 5.5 V, supports data rates up to 1 Mbps, and uses four 0.1 uF external capacitors to generate the bipolar voltage required by true RS-232 levels. A true RS-232 transceiver is an interface IC that converts logic-level signals from a UART or other asynchronous controller into bipolar RS-232 voltages, while converting received RS-232 levels back into CMOS-compatible logic. Within the electronics hierarchy, the MAX3232ECSE+ belongs to the RS-232 interface transceiver category and provides the physical-layer bridge between a digital controller and a serial-port connector. The principal operating specifications are a 3.0 V to 5.5 V supply range, a maximum data rate of 1 Mbps, and a 16-pin SOIC package. Four external 0.1 uF charge-pump capacitors simplify power-supply implementation, allowing the transceiver to operate from a single low-voltage supply rather than a separate ±12 V source. The MAX3232 family is listed in production by Analog Devices. The MAX3232E family adds ±15 kV IEC ESD protection on the serial-port pins and supports the TIA/EIA-232-F electrical interface. The dual charge-pump architecture converts the low-voltage supply into positive and negative levels needed for RS-232 signaling. The device combines one transmitter and one receiver in each direction, making it appropriate for two-wire point-to-point communication links. Typical applications include industrial serial adapters, USB-to-RS-232 interface boards, point-of-sale equipment, instrumentation, and embedded systems using UART peripherals. Its 1 Mbps capability provides ample margin for legacy serial ports, while the 3.0 V to 5.5 V supply range allows integration with both 3.3 V and 5 V digital systems. PCB design should minimize the charge-pump capacitor loop area and provide a direct return path from each capacitor to the device ground. Keep RS-232 traces short, route them away from clocks and switching nodes, and use the transceiver ground as the signal reference between the host electronics and the external connector. This product page combines manufacturer specifications, package information, verified sourcing links, drop-in replacement options, and practical interface-layout guidance to support component selection, PCB compatibility checks, and production procurement.

RFQ Contact
MAX3232ECSE+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232ECSE+T

MAX3232ECSE+T - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECSE+T is a dual-driver, dual-receiver RS-232 transceiver rated for data rates up to 1 Mbps, operation from 3.0 V to 5.5 V, and ±15 kV ESD protection in a 16-pin SOIC package. The device includes an integrated dual charge-pump circuit that converts the low-voltage supply into the positive and negative voltages required by true RS-232 drivers. Its low-power design supports modern 3.3 V and 5 V serial systems while maintaining compatibility with conventional RS-232 port levels. An RS-232 transceiver is an interface IC that converts logic-level UART signals into balanced, bipolar RS-232 signals and converts received RS-232 signals back into CMOS-compatible levels. It occupies the interface-IC branch of the broader semiconductor hierarchy, combining line drivers, line receivers, voltage conversion, and electrostatic-discharge protection into a complete serial-port interface. Two transmit channels and two receive channels make the MAX3232 family suitable for bidirectional serial links requiring full-duplex communication. Principal features include a maximum data rate of 1 Mbps, a 3.0 V to 5.5 V supply range, ±15 kV ESD protection, and a supply current reduction capability down to 10 nA. The 16-pin SOIC package is widely supported by PCB assembly and prototyping processes. Its 16-pin footprint simplifies replacement of non-enhanced RS-232 transceivers, although the electrical requirements of the connected logic and cable must still be reviewed before substitution. Internally, the MAX3232ECSE+T uses a dual charge-pump voltage converter to generate the positive supply used by one driver and the negative supply used by the other. Four external 0.1 µF charge-pump capacitors support the conversion circuit, while receiver and driver stages perform the signal-level conversion. This architecture avoids a separate external DC-to-DC converter but requires correct capacitor selection, placement, and the correct supply bypass arrangement for stable operation. Typical uses include industrial serial consoles, point-of-sale terminals, test equipment, data acquisition systems, embedded control boards, and legacy peripheral connections. The MAX3232ECSE+T is especially appropriate where a 3.3 V controller must communicate with an RS-232 device over a cable while retaining true RS-232 electrical levels. Its 1 Mbps maximum data rate supports substantially faster communication than many low-rate legacy transceivers. For layout, place the charge-pump capacitors and supply bypass capacitor close to their associated pins, and keep the RS-232 driver outputs away from sensitive low-level inputs. Confirm that the host UART operates at the logic levels expected by the transceiver and verify cable length, grounding, and connector exposure against the required system ESD and EMC conditions.

RFQ Contact
MAX3232ECTE+ - Dual 1Mbps RS-232 TQFN | Analog Devices
MAX3232ECTE+

MAX3232ECTE+ - Dual 1Mbps RS-232 TQFN | Analog Devices

Analog Devices MAX3232ECTE+ is a dual-transceiver, dual-receiver RS-232 interface IC operating from 3.0V to 5.5V, supporting data rates up to 1Mbps in a 16-pin TQFN package with an exposed pad. The device provides two transmit drivers, two receive receivers, true RS-232 signal levels, and enhanced electrostatic-discharge protection rated to ±15kV. An RS-232 transceiver is a signal-interface IC that converts logic-level UART signals between a host controller and the bipolar, positive and negative voltage levels required by RS-232 links. Within the interface-IC hierarchy, the MAX3232 belongs to the RS-232 transceiver class, which combines line drivers, receivers, charge-pump circuitry, and ESD protection in one device. It provides a practical bridge between CMOS/TTL digital systems and legacy point-to-point serial equipment. Key features include a 3.0V to 5.5V supply range, operation at rates up to 1Mbps, and shutdown-related supply current as low as 10nA. The integrated charge-pump circuitry generates the RS-232 transmit voltage without requiring an external negative supply. Two drivers and two receivers support simultaneous bidirectional serial communication, while ±15kV protection helps improve robustness when cables are connected or disconnected. The MAX3232 architecture integrates the charge pump, drivers, receivers, and protection functions into one interface device. Its true RS-232 implementation uses differential charge-pump-derived output levels, while the receiver threshold supports standard RS-232 signaling. The exposed-pad TQFN construction permits improved heat transfer when a nearby supply and ground plane are used, although RS-232 interface dissipation is normally lower than that of a power regulator or processor. Typical uses include industrial serial consoles, instrumentation, barcode scanners, laboratory equipment, embedded control systems, and service interfaces for computers or networking equipment. The 1Mbps capability supports faster legacy serial links than the commonly encountered 250kbps class, while its 3.0V minimum supply makes it suitable for mixed-voltage embedded systems. PCB design should provide uninterrupted ground-plane connectivity beneath the exposed pad and place charge-pump capacitors close to their specified pins. Route the RS-232 driver and receiver nets away from sensitive analog or high-speed digital traces, and follow the manufacturer datasheet when selecting bypass capacitors and exposed-pad solder geometry. This page combines the exact MAX3232ECTE+ ordering information, verified technical characteristics, same-package replacement analysis, comparison parameters, and practical layout guidance. It is intended to help engineers identify whether the device can replace an existing RS-232 interface without changing the PCB footprint or redesigning the surrounding system.

RFQ Contact
MAX3232ECTE+T - 1Mbps True RS-232 Transceiver | Analog Devices
MAX3232ECTE+T

MAX3232ECTE+T - 1Mbps True RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232ECTE+T is a dual RS-232 transceiver with two drivers and two receivers, a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, and 15 kV ESD protection. It is packaged in a 16-pin TQFN with an exposed pad, a 5 mm by 5 mm surface-mount package intended for compact RS-232 interface designs. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. MAX3232 belongs to the RS-232 transceiver hierarchy within interface ICs, where the dual charge-pump circuit supports the positive and negative voltage swings required by true RS-232. The MAX3232 family is identified by Analog Devices as pin, package, and functionally compatible with the industry-standard MAX232. Key characteristics include a 3.0 V minimum operating supply, a 5.5 V maximum operating supply, and a data rate of up to 1 Mbps. The device integrates two line drivers and two line receivers. Its low-power design can operate from a 3.3 V system without a separate 5 V supply. The specified 15 kV ESD protection improves robustness on exposed serial connectors, although system-level grounding and cable design remain important. Internally, the MAX3232 combines its dual charge pump, two transmit drivers, and two receive receivers in one interface device. The charge pump generates the voltage needed for RS-232 output levels, while the receivers include the signal-conditioning functions needed to reject noise and recover logic-level data. The exposed thermal pad supports heat transfer from the device, and the 5 mm by 5 mm package reduces board area compared with larger leaded and SOIC implementations. Typical uses include industrial serial-port adapters, USB-to-RS-232 equipment, instrumentation interfaces, POS terminals, embedded control systems, and data-acquisition equipment. The 1 Mbps capability supports higher-rate legacy serial links while the 3.3 V supply operation simplifies integration with modern embedded controllers and FPGAs. Designers should still confirm signal levels, connector requirements, and cable length against the complete interface specification. For a new layout, place the charge-pump capacitors and RS-232 interface components close to their associated pins. Keep the exposed pad connected to the ground plane on a multilayer board, use the recommended via pattern, and provide the interface connector with an appropriate chassis or signal-ground strategy. The MAX3232ECTE+T is supplied in tape-and-reel packaging for automated assembly. This product page combines the manufacturer specifications, package details, verified lifecycle information, pin-compatible family alternatives, and application-specific design guidance. It also highlights the differences engineers should evaluate when moving between commercial and extended-temperature MAX3232 package variants.

RFQ Contact
MAX3232ECUE+ - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232ECUE+

MAX3232ECUE+ - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECUE+ is a 2/2 true RS-232 transceiver with two drivers and two receivers, 3.0 V to 5.5 V operation, data rates up to 1 Mbps, and ±15 kV ESD protection in a 16-pin TSSOP package. It converts TTL/CMOS logic levels to true RS-232 levels and back, allowing modern digital controllers to communicate with legacy serial equipment. A true RS-232 transceiver is an interface IC within the broader communication-IC and interface-IC hierarchy. Its transmitters generate the bipolar voltage swings required by RS-232, while its receivers detect valid logic states after the cable has introduced attenuation, noise, and level inversion. The MAX3232 integrates this interface with an on-chip charge pump, eliminating the external ±12 V supply normally associated with older RS-232 implementations. The MAX3232ECUE+ supports a 3.0 V to 5.5 V supply, operation at data rates up to 1 Mbps, and shutdown current down to 10 nA. Its ±15 kV ESD protection applies to the RS-232 pins and helps improve interface ruggedness in exposed industrial, communications, instrumentation, and consumer equipment. The device provides a compact 16-pin TSSOP option for space-constrained circuit boards. Internally, the IC combines two line drivers, two line receivers, and a dual charge-pump voltage converter. The charge pump generates the positive and negative transmitter voltages from a single low-voltage supply, while the receivers translate the returned bipolar signal into a CMOS-compatible output. Because the MAX3232 is labeled a production device by Analog Devices, it is positioned as an active RS-232 interface option rather than a legacy-only component. Typical uses include serial-port adapters, industrial control links, point-of-sale equipment, barcode scanners, instrumentation, embedded systems, and data cables where a host UART requires RS-232 electrical levels. The up-to-1-Mbps capability supports faster serial links than the commonly cited 250-kbps class, provided the connected cable, connector, grounding, and receiving equipment meet the required signal conditions. When laying out the circuit, place the charge-pump capacitors and the driver and receiver interface components according to the manufacturer datasheet layout guidance. Keep the high-voltage RS-232 driver traces away from sensitive low-level logic, preserve the specified ground connection, and provide unobstructed ESD paths at connector entry points. The exact pin names and capacitor values should be assigned from the manufacturer pin-description and application tables. This page combines the verified electrical and package characteristics, production status, commercial information, drop-in alternatives, and practical design considerations needed to evaluate the MAX3232ECUE+. It is intended to help engineers distinguish its low-voltage operation, 1-Mbps capability, enhanced ESD protection, and TSSOP footprint from other RS-232 interface implementations.

RFQ Contact
MAX3232ECUE+T - 3.0-5.5V RS-232 Transceiver | Analog Devices
MAX3232ECUE+T

MAX3232ECUE+T - 3.0-5.5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232ECUE+T is a true RS-232 transceiver containing two line drivers and two line receivers, operating from a 3.0 V to 5.5 V single supply with data rates up to 1 Mbps. The device is offered in a 16-pin TSSOP package and includes enhanced electrostatic-discharge protection, with RS-232 line-driver outputs designed for low-power communication links. A true RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals between a host controller and a serial connector. It belongs to the transceiver and line-driver category, which forms part of interface ICs and the broader semiconductor hierarchy. Unlike RS-422 or RS-485, true RS-232 uses unbalanced, single-ended signaling and requires bipolar voltage levels at the line-driver outputs. This MAX3232 device uses internal charge pumps to generate the positive and negative voltages required by those levels. Key features include a 3.0 V to 5.5 V supply range, operation at data rates up to 1 Mbps, true RS-232 line-driver and receiver functions, and enhanced ESD protection rated to ±15 kV on applicable device variants. The low-power design is suitable for equipment operating from regulated 3.3 V or 5 V rails. The MAX3232 family is also identified by Analog Devices as being pin, package, and functionally compatible with the industry-standard MAX232 when its electrical and protection requirements match. The MAX3232EC integrates two transmitters, two receivers, and a dual charge-pump circuit. The receivers support low-power operation and provide the threshold behavior required by EIA/TIA-232 links. Internal charge-pump capacitors and external storage capacitors support the bipolar line-driver output. Compared with discrete RS-232 driver and receiver circuits, the integrated approach reduces component count and simplifies the physical implementation of a two-channel serial interface. Typical uses include data cables, point-of-sale equipment, industrial control links, instrumentation, and embedded systems that exchange data through an RS-232 port. The 1 Mbps capability permits faster asynchronous communication than many legacy RS-232 designs, while the 16-pin TSSOP package supports compact surface-mount layouts. The device can also pair with a microcontroller UART when the logic side operates from the same 3.0 V to 5.5 V supply domain. When laying out the circuit, place charge-pump and storage capacitors close to their associated pins, route the RS-232 driver outputs directly toward the connector, and keep the logic-side traces away from exposed cable interfaces. ESD protection helps reduce connector stress, but it does not replace a correctly designed protective network and properly grounded connector. Confirm the external capacitor values and pin-specific recommendations in the manufacturer datasheet before releasing a PCB. This product page combines the manufacturer specifications, exact-package sourcing information, documented cross-reference candidates, application guidance, and selection trade-offs for engineers evaluating the MAX3232ECUE+T in a compact 3.3 V or 5 V RS-232 interface.

RFQ Contact
MAX3232ECUP+ - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232ECUP+

MAX3232ECUP+ - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232ECUP+ is a low-power, true RS-232 transceiver with two drivers and two receivers, a maximum data rate of 1 Mbps, and a 3.0 V to 5.5 V supply range. It is housed in a 20-pin TSSOP package and provides ±15 kV ESD protection on the serial-port connection pins according to the manufacturer product page. A true RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar levels and converts incoming RS-232 signals back into CMOS-compatible logic. Within the interface hierarchy, the MAX3232ECUP+ belongs to the RS-232 transceiver class, which is part of the broader line-driver and line-receiver family within interface ICs. Its internal dual charge pump supports the voltage swings required for true RS-232 communication. Key features include operation from 3.0 V to 5.5 V, data rates up to 1 Mbps, ±15 kV ESD protection, and a supply current as low as 10 nA. Two transmit channels and two receive channels support full-duplex serial links. The E suffix identifies the enhanced ESD-protected version, while the UP package code corresponds to the 20-pin TSSOP used by this ordering variant. Technically, the device combines a dual charge-pump circuit with four small charge-pump capacitors, two line drivers, and two line receivers. The charge pump develops positive and negative voltage rails needed by the transmitter outputs, allowing true RS-232 operation from a single low-voltage supply. Receiver inputs provide the electrical boundary between the ±RS-232 signal environment and a host UART operating at CMOS logic levels. Typical uses include industrial serial consoles, data-acquisition equipment, point-of-sale systems, instrumentation, and embedded control boards. The 1 Mbps capability is useful for links requiring faster transfers than conventional low-speed serial ports, while the 3.0 V minimum supply supports modern 3.3 V systems. For 5 V systems, the same part operates within its stated upper supply limit. PCB design should place the charge-pump capacitors close to their associated pins and provide a continuous ground return from the interface connector. Keep RS-232 traces away from sensitive analog or high-speed digital nets, use appropriate surge and ESD protection for exposed cables, and validate the external charge-pump capacitor values against the manufacturer datasheet. This product page combines the manufacturer specifications, package details, pricing channels, replacement analysis, and practical PCB guidance. It also distinguishes genuine same-footprint alternatives from functional substitutes, helping engineers shorten qualification and sourcing work without overlooking charge-pump, ESD, speed, or shutdown differences.

RFQ Contact
MAX3232ECUP+G071 - 1 Mbps RS-232 Transceiver | Analog Devices
MAX3232ECUP+G071

MAX3232ECUP+G071 - 1 Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECUP+G071 is a dual-driver, dual-receiver RS-232 transceiver designed for reliable serial data transmission at speeds up to 1 Mbps. It operates from a 3.0 V to 5.5 V supply and is available in a 20-pin TSSOP package. The device provides ±15 kV ESD protection, low-power operation, and TrueRS-232 signal handling for equipment that communicates through legacy serial ports. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX3232E family belongs to the interface IC hierarchy, combining line drivers, line receivers, and an on-chip voltage converter. This makes it useful in industrial controls, test equipment, point-of-sale terminals, embedded systems, and computer peripherals where the host uses a conventional serial interface. The MAX3232ECUP+G071 supports operation from 3.0 V to 5.5 V, with communication rates up to 1 Mbps. Its ±15 kV ESD protection helps improve reliability when cables are connected to exposed connectors. The 20-pin TSSOP package supports compact, surface-mount PCB layouts, while the MAX3232E family is designed to be pin-, package-, and functionally compatible with the industry-standard MAX232, according to Analog Devices. The integrated charge-pump circuitry provides the bipolar voltage levels required by RS-232 without requiring an external power supply. External capacitors are used with the on-chip charge pump, while the driver and receiver sections support two transmit channels and two receive channels. This combination is useful when a system needs bidirectional serial communication but does not require a full multi-channel RS-232 port. Typical uses include industrial serial controllers, laboratory instruments, barcode and scanner interfaces, POS equipment, access-control systems, and embedded diagnostic equipment. In these applications, the device can bridge a low-voltage microcontroller UART to an RS-232 connector while providing ESD protection at the physical interface. Designers should follow the manufacturer datasheet for the exact charge-pump capacitor values, bypass-capacitor recommendations, RS-232 connector protection, and pin assignments. PCB layout should keep the charge-pump and bypass capacitors close to their associated pins, and the signal path should be routed away from noisy switching nodes. The TSSOP-20 footprint should also be checked against the PCB library before placement because package suffix codes identify the exact ordering configuration.

RFQ Contact
MAX3232ECUP+T - 1Mbps True RS-232 Transceiver | Analog Devices
MAX3232ECUP+T

MAX3232ECUP+T - 1Mbps True RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECUP+T is a dual-driver, dual-receiver true RS-232 transceiver operating from a 3.0V to 5.5V single supply. It supports data rates up to 1Mbps and provides ±15kV ESD protection on the serial interface pins. The device is packaged in a 20-pin TSSOP package and is intended for industrial, instrumentation, communications, and embedded equipment using the EIA/TIA-232 serial interface. An RS-232 transceiver is an interface IC that translates logic-level TTL or CMOS signals into balanced, single-ended RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. The MAX3232 combines two line drivers, two line receivers, and an onboard dual charge-pump circuit. This charge-pump arrangement generates the positive and negative voltages required for compliant RS-232 transmission without a separate negative supply rail. Key features include true RS-232 operation, 3.0V to 5.5V supply compatibility, throughput up to 1Mbps, and ±15kV ESD protection. The receiver can remain active while the transmitter is disabled, supporting shared-bus and locally managed systems. Low-power operation and a supply current as low as 10nA make the device suitable for energy-conscious ports that spend substantial time idle. The MAX3232 uses external charge-pump capacitors to establish the RS-232 voltage levels. Its integrated architecture reduces the number of external components compared with older discrete charge-pump implementations, while the single-supply operation simplifies power planning in systems that also contain 3.3V or 5V digital logic. Interface protection is particularly important where a serial cable connects externally accessible equipment to a control board. Typical applications include RS-232 ports on industrial controllers, test and measurement instruments, point-of-sale equipment, barcode scanners, and embedded systems. The device can also translate between a host UART and an RS-232 bus, including systems that require hardware handshaking through the request-to-send and clear-to-send lines. Design the serial connector, protection network, charge-pump capacitors, and ground return as one signal-integrity system. Keep charge-pump capacitor connections short, provide a solid ground plane, and use an interface connector with suitable surge and ESD protection when the cable is exposed to user-accessible environments. This page combines manufacturer specifications, sourcing guidance, verified drop-in alternatives, comparison parameters, and practical PCB considerations to support faster component selection and robust RS-232 interface implementation.

RFQ Contact
MAX3232ECUP+TG071 - 3V Dual RS-232 | Analog Devices
MAX3232ECUP+TG071

MAX3232ECUP+TG071 - 3V Dual RS-232 | Analog Devices

The Analog Devices MAX3232ECUP+TG071 is a dual-transmitter, dual-receiver RS-232 interface transceiver operating from 3.0 V to 5.5 V, with a listed data rate of 250 kbps, in a 20-pin TSSOP package. It is designed for bidirectional serial-port conversion between RS-232 logic levels and CMOS/TTL signals. The device also supports operation up to 1 Mbps, provides ±15 kV ESD protection, and features a low-power shutdown current down to 10 nA. An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between a modern digital system and an RS-232 port. It converts low-voltage digital transmitter and receiver signals into RS-232-compatible levels in one direction and translates incoming RS-232 levels back into logic-compatible signals in the other. Within the signal-chain hierarchy, the MAX3232ECUP+TG071 belongs to the RS-232 transceiver class, interface IC category, and broader semiconductor product family. The MAX3232ECUP+TG071 integrates two transmitters and two receivers, allowing two communication channels to share one package. Its 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V system rails. The ±15 kV ESD protection improves resilience when a cable-connected port is exposed to electrostatic discharge, while the low 10 nA power-down current is useful for portable or intermittently powered equipment. True RS-232 operation requires a charge-pump circuit to generate the positive and negative voltages required by the RS-232 specification. The MAX3232ECUP+TG071 integrates this function with the drivers and receivers, reducing external component count compared with discrete implementations. Its dual-channel architecture also supports hardware flow-control signals when additional receiver or transmitter channels are required by the host interface. Typical uses include industrial serial adapters, POS terminals, test equipment, data acquisition systems, embedded control panels, and service interfaces. A 3.3 V controller can use the device for a 2/2 RS-232 channel implementation, while a 5 V system can operate within the same supported supply range. The 20-pin TSSOP footprint supports compact, surface-mount PCB construction. For reliable implementation, place the charge-pump capacitors and transceiver interface components close to their associated pins, route the RS-232 traces away from sensitive analog or high-speed digital paths, and connect the ground reference as specified in the manufacturer datasheet. Verify the complete external capacitor network against the device's recommended circuit before layout release. This product page consolidates the electrical ratings, package information, drop-in comparison options, application guidance, and practical design considerations needed to evaluate the MAX3232ECUP+TG071 for a new RS-232 interface.

RFQ Contact
MAX3232ECWE+ - Dual 1Mbps RS-232 Transceiver | Maxim
MAX3232ECWE+

MAX3232ECWE+ - Dual 1Mbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3232ECWE+ is a dual-driver, dual-receiver RS-232 interface transceiver operating from 3.0 V to 5.5 V at data rates up to 1 Mbps. It uses four external 0.1 µF charge-pump capacitors and is packaged in a 16-pin SOIC for industrial RS-232 links. An RS-232 transceiver is an interface IC that converts logic-level TTL signals into RS-232 voltage levels and converts incoming RS-232 signals back into CMOS-compatible levels. The MAX3232 belongs to the transceiver hierarchy: RS-232 interface IC, driver and receiver, communication interface, and integrated circuit. Its two transmitters and two receivers support full-duplex serial connections where data can be transmitted and received simultaneously. Key features include ±15 kV ESD protection, low-power operation down to 10 nA, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps. The device is specifically described as a true RS-232 transceiver rather than an RS-422 or RS-485 interface. Its four external charge-pump capacitors reduce the number of required support components while maintaining the voltage translation required by the RS-232 standard. The MAX3232 product family also provides pin, package, and functional compatibility with the industry-standard MAX232 according to the Analog Devices product page. This compatibility makes the MAX3232 suitable for established MAX232 footprints and eases design migration when improved ESD protection, low-power behavior, or a 3.0 V minimum supply is required. The MAX3232ECWE+ ordering code identifies the 16-pin SOIC industrial-temperature option, although exact temperature limits should be confirmed in the manufacturer datasheet. Typical applications include industrial serial controllers, point-of-sale equipment, instrumentation, data-acquisition systems, and embedded systems that connect a host UART to an RS-232 port. The ±15 kV protection rating is especially useful where a cable-connected port can be exposed to electrostatic discharge. Operating at up to 1 Mbps accommodates high-speed data acquisition and legacy industrial peripherals. Design the charge-pump capacitor network close to the C1 and C2 pins, observe the polarity and voltage ratings of all four capacitors, and route the RS-232 connector interface away from sensitive analog circuitry. Confirm that the external capacitors meet the capacitance and dielectric requirements in the datasheet because incorrect values can affect startup behavior, line-driver performance, or data integrity. This page combines manufacturer specifications, package and lifecycle information, structured drop-in alternatives, interface selection guidance, and practical PCB-design notes. These engineering details help shorten component selection and support a more reliable transition from MAX3232-family circuits to qualified alternatives.

RFQ Contact
MAX3232ECWE+T - 1Mbps Dual RS-232 Transceiver | Analog Devices
MAX3232ECWE+T

MAX3232ECWE+T - 1Mbps Dual RS-232 Transceiver | Analog Devices

Analog Devices MAX3232ECWE+T is a dual, full-duplex RS-232 transceiver designed for data rates up to 1 Mbps, with operation from a 3.0 V to 5.5 V supply. It provides two drivers and two receivers in a 16-pin SOIC package and is specified for ±15 kV ESD protection. The transceiver family also supports low-power operation with shutdown load current down to 10 nA. An RS-232 transceiver is an interface IC that converts digital logic-level signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible levels. In the broader hierarchy, the MAX3232 belongs to the interface IC category, connects digital systems to the RS-232 physical layer, and is commonly positioned between a UART, microcontroller, or industrial controller and an external RS-232 port. Its integrated level translation reduces the number of external components required for a conventional RS-232 connection. Key features include true RS-232 operation, 3.0 V to 5.5 V supply compatibility, data rates up to 1 Mbps, and ESD protection rated to ±15 kV. The two-driver, two-receiver arrangement supports one full-duplex RS-232 port with independently assignable driver and receiver channels. Low-power shutdown capability is useful when a connected equipment must reduce current consumption while preserving the link for later restart. The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltages required by RS-232 from a single low-voltage supply. This allows operation from 3.0 V to 5.5 V without a negative supply rail. The MAX3232E devices maintain pin, package, and functional compatibility with the industry-standard MAX232, which simplifies upgrades in existing RS-232 designs. Typical uses include industrial control consoles, data acquisition equipment, test and measurement instruments, point-of-sale terminals, and service interfaces for embedded systems. The 1 Mbps maximum data rate is suitable for short-distance serial links carrying configuration data, status messages, and command traffic. A receiving system must still account for RS-232 cable length, grounding, and signal-integrity limitations. For reliable layout, follow the manufacturer datasheet capacitor recommendations and place charge-pump and interface-decoupling components close to their associated pins. Keep the RS-232 connector path physically separated from sensitive analog and high-speed digital traces, and provide a suitable chassis or signal ground strategy to reduce ground-offset errors. This product page consolidates the exact orderable MPN, key electrical ratings, drop-in replacement options, interface applications, and implementation guidance. It also distinguishes direct same-footprint choices from alternatives that require a separate qualification review before use in an existing board.

RFQ Contact
MAX3232EEAE+ - 15kV ESD 16-SSOP RS-232 IC | Analog Devices
MAX3232EEAE+

MAX3232EEAE+ - 15kV ESD 16-SSOP RS-232 IC | Analog Devices

The Analog Devices MAX3232EEAE+ is a 2-driver/2-receiver true RS-232 transceiver with ±15 kV ESD protection, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps in a 16-pin SSOP package. The interface converts logic-level signals between an asynchronous controller and a serial connector while maintaining RS-232 electrical behavior. A true RS-232 transceiver is an interface IC that integrates line drivers, line receivers, and charge-pump circuitry. Its role in the hierarchy is UART controller to RS-232 transceiver to serial connector. This is different from a UART transceiver that handles only logic-level signaling or an RS-485 interface, which uses differential signaling. The MAX3232EEAE+ is intended for industrial-control, instrumentation, and embedded data links requiring a compact multi-line interface. The main features include two transmit drivers, two receive receivers, dual charge-pump voltage generation, ±15 kV ESD protection, and a low-power design described as operating down to 10 nA. Its 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Data rates of up to 1 Mbps make the device suitable for moderate-speed serial links, including legacy RS-232 ports, point-to-point equipment interfaces, and industrial service connections. The dual charge-pump architecture generates the positive and negative voltage levels required by true RS-232 drivers from a single low-voltage supply. Four external charge-pump capacitors support the internal voltage conversion. The integrated receivers invert the incoming RS-232 levels and provide compatible logic-level outputs to the host UART. The Analog Devices MAX3232E data sheet, Rev. 13, identifies the device as a true RS-232 transceiver with pin-to-pin protection on the serial-port connections. Typical applications include industrial serial adapters, programmable-logic-controller service ports, instrumentation interfaces, embedded controller communication, and point-to-point control links. The compact 16-pin SSOP package helps reduce board area when two drivers and two receivers are required. The 1 Mbps maximum data rate provides ample margin for many legacy serial protocols, although cable length, baud rate, grounding, and signal integrity must be evaluated together. For layout, follow the charge-pump capacitor connections and polarity shown in the manufacturer data sheet exactly. Place the four external capacitors close to their associated pins, route serial outputs away from sensitive analog inputs, and provide a low-impedance return path between connected equipment. Use an appropriate connector and board-level protection strategy when exposed cables carry greater electrostatic-discharge risk. This page combines the MAX3232E family specifications, ordering information, pin-compatible alternatives, application guidance, and practical interface-design notes. It is intended to help engineers confirm package fit, voltage compatibility, protection requirements, and replacement strategy before integrating the MAX3232EEAE+ into an RS-232 design.

RFQ Contact
MAX3232EEAE+G1Z - Dual RS-232 Transceiver | Analog Devices
MAX3232EEAE+G1Z

MAX3232EEAE+G1Z - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEAE+G1Z is a 2-driver/2-receiver full RS-232 transceiver designed for serial-interface systems operating from 3.0 V to 5.5 V. It supports data rates up to 1 Mbps, provides ±15 kV ESD protection, and is offered in a 16-pin SSOP package. The G1Z ordering designation identifies the qualified configuration associated with this MAX3232E-family device. An RS-232 transceiver is an interface IC that translates between logic-level signals used by digital circuits and the voltage levels defined for RS-232 serial links. A full transceiver combines transmit and receive functions in one package. The MAX3232EEAE+G1Z provides two transmit channels and two receive channels, allowing a board to exchange data in both directions while limiting the number of external interface components and conserving board area. The device operates from a 3.0 V minimum supply to a 5.5 V maximum supply, accommodating common 3.3 V and 5 V system rails. Its maximum supported data rate of 1 Mbps makes it suitable for instrument control, configuration interfaces, point-of-sale equipment, and other systems that transfer moderate amounts of serial data. The stated ±15 kV ESD protection helps strengthen the interface against electrostatic discharge encountered during handling and connection. As a true RS-232 transceiver, the MAX3232EEAE+G1Z is intended for point-to-point serial communication rather than a multipoint bus. Each driver converts logic-level inputs into RS-232 output levels, while each receiver converts incoming RS-232 signals into logic-level outputs. This division of functions allows two device-to-device channels to operate in opposite directions within one compact interface circuit. Typical uses include industrial control equipment, test and measurement instruments, transactional terminals, security-system accessories, and embedded service ports. Designers should pair the IC with the charge-pump and interface components specified by the manufacturer, observe the recommended pin connections, and validate signal integrity at the intended baud rate and cable length. The principal design consideration is that RS-232 is a single-ended, point-to-point interface whose voltage levels differ from modern CMOS logic. Correct driver population, supply decoupling, grounding, connector exposure, and cable routing are therefore more important than treating the transceiver as an ordinary UART peripheral. Confirm every board-level connection against the MAX3232E datasheet before production release. This product page combines the manufacturer's device positioning with package, interface, sourcing, and replacement information designed for faster engineering evaluation. It also distinguishes electrically interchangeable ordering variants from design changes that would require a different package or a redesigned RS-232 interface.

RFQ Contact