Texas Instruments

MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

MPN: MAX3232EIDBR ✓ Active
3 V to 5.5 V Vdss 16-pin SSOP, 5.30 mm width Package
MOQ: 1 |

MAX3232EIDBR Overview

The Texas Instruments MAX3232EIDBR is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data-signaling rates up to 250 kbit/s. The device is housed in a 16-pin SSOP package and provides ±15 kV IEC ESD protection on the serial-port connection pins. It interfaces a host UART or asynchronous controller with an RS-232 connector while the integrated dual charge pump supplies the required bipolar line voltage.

An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDBR is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART.

Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables.

The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered.

Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins.

For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing.

This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.

Drop-in alternatives for MAX3232EIDBR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MAX3232EIDBR (same form factor and footprint) — differing in Package, Supply Voltage Range, Maximum Data Rate, Device Type, ESD Protection.

Analog Devices
Package: 16-pin SSOP
Supply Voltage Range: 3.0 V to 5.5 V
Maximum Data Rate: 1 Mbps
Compare with MAX3232EIDBR →
Texas Instruments
Package: 16-SSOP (DB, 0.209 in / 5.30 mm width)
Compare with MAX3232EIDBR →
Texas Instruments
Device Type: Transceiver
ESD Protection: ±15 kV
Compare with MAX3232EIDBR →

MAX3232ECDB

✅ Drop-In
Texas Instruments
📦 16-pin SSOP
RS-232 · Transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbps (minimum) · ±15 kV (HBM) · ±15 kV contact discharge / ±15 kV air-gap discharge

Contact for price

View Datasheet →

MAX3232IDB

✅ Drop-In
Texas Instruments
📦 16-pin SSOP
Dual RS-232 line driver and receiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 5 V logic compatible · 0.1 µF each, 4 capacitors · ±15 kV

Contact for price

View Datasheet →

MAX3232CAE+

✅ Drop-In
Analog Devices
📦 16-pin SSOP
RS-232 interface transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · True RS-232 · 16-pin SSOP · Dual charge pump

Contact for price

View Datasheet →

MAX3232EIDBR Specifications

Device Type Dual RS-232 line driver and receiver
Number of Driver Channels 2 channels
Number of Receiver Channels 2 channels
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbit/s
Driver Output Slew Rate 30 V/µs maximum
ESD Protection ±15 kV IEC ESD protection
RS-232 Standard TIA/EIA-232-F
Charge Pump Dual charge-pump circuit
External Charge-Pump Capacitors 4 capacitors
Package 16-pin SSOP, 5.30 mm width
Mounting Type Surface mount

MAX3232EIDBR 16-pin ssop, 5.30 mm width Pin Configuration Guide

Pin configuration for MAX3232EIDBR (16-pin ssop, 5.30 mm width package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

16-pin ssop, 5.30 mm width package pinout diagram for MAX3232EIDBR

No detailed pinout data available for MAX3232EIDBR.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX3232EIDBR is suitable for 6 applications: Industrial Equipment Serial Console, Laboratory Instrument Connectivity, Point-of-Sale Terminal Interface, Security and Access-Control Systems, Legacy Computer Service Port, Embedded UART-to-RS-232 Bridge.

🏭

Industrial Equipment Serial Console

The MAX3232EIDBR is well suited to an industrial controller that exposes a serial console over an RS-232 connector. Its 3 V to 5.5 V single-supply operation allows direct use of a 3.3 V embedded system, while the integrated dual charge pump generates the bipolar RS-232 levels without a negative rail. A maximum signaling rate of 250 kbit/s covers many diagnostic and configuration protocols. The ±15 kV IEC ESD rating on the serial-port pins improves protection at an exposed connector, although the PCB should still use a clean ground reference and appropriately routed interface traces. Engineers should verify protocol baud-rate margin, cable length, and the host-side logic levels before finalizing the interface.

🔧

Laboratory Instrument Connectivity

The MAX3232EIDBR can connect a laboratory instrument controller to a conventional RS-232 service or measurement port. Operating from a single 3 V to 5.5 V rail simplifies power planning in compact test equipment, and the dual driver and dual receiver arrangement supports two communication paths when both sides are active. Its 250 kbit/s limit is appropriate for many legacy instrument-control protocols but should be compared with the instrument's maximum supported rate. The driver's controlled slew rate of no more than 30 V/µs helps limit cable-edge energy, while the ±15 kV IEC ESD protection provides useful robustness for a connector that may be touched during routine service.

🖥️

Point-of-Sale Terminal Interface

The MAX3232EIDBR fits point-of-sale and peripheral controllers that need a legacy RS-232 link alongside a low-voltage digital processor. The device's two transmitters and two receivers permit RS-232 communication in both directions, while the integrated charge pump eliminates a separate negative supply and reduces board complexity. Its 250 kbit/s maximum data rate is more than adequate for many transaction and configuration channels, though it is not a substitute for a higher-speed differential interface. The ±15 kV IEC ESD protection is particularly relevant at externally accessible POS connectors. Firmware should also support timeout and line-state handling so that a disconnected or partially driven peripheral does not block the terminal.

🎥

Security and Access-Control Systems

The MAX3232EIDBR can provide a wired RS-232 commissioning or diagnostic path in security panels, access-control readers, and camera-support equipment. The 3.3 V-compatible supply range is useful alongside modern embedded processors, while the internal charge-pump arrangement allows operation without a negative supply. Two drivers and two receivers provide flexibility for bidirectional equipment links, and the 250 kbit/s ceiling suits many command and status protocols. For exposed installations, the documented ±15 kV IEC ESD protection adds value at the serial connector, but it does not replace coordinated surge protection, cable routing, or grounding. Firmware should validate received command bytes before changing security-sensitive states.

💻

Legacy Computer Service Port

The MAX3232EIDBR is useful for adding a modern controller to a legacy computer or embedded service port that still uses RS-232. Its single 3 V to 5.5 V supply operation simplifies level adaptation without requiring a separate negative rail, and the integrated charge pump supplies the compliant bipolar signal internally. The 250 kbit/s maximum rate supports common UART service protocols, while the 30 V/µs maximum driver slew rate limits fast cable transitions. The ±15 kV IEC ESD protection strengthens the connector side of the design. Engineers should check null-modem or straight-through wiring, request-to-send behavior where applicable, ground continuity, and whether the legacy host requires a lower signaling rate than the transceiver maximum.

🧩

Embedded UART-to-RS-232 Bridge

The MAX3232EIDBR provides a compact bridge between a host UART and an RS-232 physical layer. Its two drivers and two receivers support a full-duplex link, while the single 3 V to 5.5 V supply is compatible with embedded 3.3 V platforms. The 250 kbit/s ceiling should be treated as the maximum supported link rate, not as a target for marginal designs; leave timing margin for framing, parity, and system latency. Four external charge-pump capacitors are required, so their placement should follow the manufacturer layout guidance to preserve charge-pump performance. The ±15 kV IEC ESD protection on connection pins improves robustness, but long cables may still benefit from dedicated overvoltage and surge protection.

What is the operating voltage of MAX3232EIDBR?
The MAX3232EIDBR operates from a single 3 V to 5.5 V supply. According to the Texas Instruments MAX3232E product page and datasheet, this range allows the interface to work with both 3.3 V and 5 V host systems while an integrated dual charge pump generates the bipolar voltage required for RS-232 communication. The device therefore does not require a separate negative supply rail.
What is the maximum data rate of MAX3232EIDBR?
The MAX3232EIDBR supports RS-232 data-signaling rates up to 250 kbit/s. Texas Instruments states in the MAX3232E datasheet that the device includes two line drivers, two line receivers, and a dual charge-pump circuit. Its maximum driver output slew rate is 30 V/µs, which helps control edge rate and reduce ringing on longer RS-232 connections.
Where can I download the MAX3232EIDBR datasheet PDF?
The official MAX3232E datasheet PDF is available from the Texas Instruments product link at https://www.ti.com/lit/gpn/MAX3232E. It contains the ordering information, electrical characteristics, charge-pump arrangement, ESD ratings, typical interface circuit, and pin descriptions needed for a MAX3232EIDBR design. Use the ordering table to confirm the selected package and temperature option before releasing the design.
Where can I find the MAX3232EIDBR pinout?
The MAX3232EIDBR pinout is found in the pin-configuration and pin-description sections of the Texas Instruments MAX3232E datasheet. The device uses a 16-pin SSOP package. When assigning PCB nets, follow the exact pin numbers and signal names printed in the datasheet, and connect the four external charge-pump capacitors only to the pins identified by the manufacturer application diagram.
Does MAX3232EIDBR need a negative power supply?
No, the MAX3232EIDBR does not require an external negative power supply. According to the Texas Instruments MAX3232E datasheet, a dual charge-pump circuit and four small external capacitors create the positive and negative voltages needed by the RS-232 drivers from one 3 V to 5.5 V supply. This simplifies the power design in systems whose host operates entirely from a low-voltage rail.
What ESD protection does MAX3232EIDBR provide?
The MAX3232EIDBR provides ±15 kV IEC ESD protection on the serial-port connection pins, including ground. Texas Instruments identifies the MAX3232E as a dual RS-232 interface with enhanced ESD protection. This rating strengthens the connector-side interface against electrostatic discharge, although board layout, cable protection, and system-level grounding still determine the final surge resilience.
What can replace MAX3232EIDBR?
MAX3232EIDBR can be replaced only after confirming the exact package, pin arrangement, supply range, data rate, and protection rating. The closest same-manufacturer candidates include MAX3232ECDB, MAX3232IDB, and MAX3232CAE+, which appear in manufacturer comparison or cross-reference material. Review the datasheet truth tables and electrical characteristics before treating any candidate as a production drop-in replacement.
Is MAX3232EIDBR the same as MAX3232IDB?
MAX3232EIDBR and MAX3232IDB are closely related dual RS-232 transceivers, but they should not be treated as identical without checking the complete ordering table. The MAX3232E family is identified by Texas Instruments as having ±15 kV IEC ESD protection, while the MAX3232IDB listing is a distinct orderable variant. Confirm temperature grade, package, and ESD requirements for the specific assembly.
MAX3232EIDBR vs MAX3232CAE+ - which is better for an industrial controller?
The MAX3232EIDBR is the clearer choice when ±15 kV IEC ESD protection and a documented industrial-oriented package option are priorities. The MAX3232CAE+ is also a dual RS-232 transceiver in a 16-pin SSOP package, so its line-driver and receiver functions are closely aligned. The final choice depends on temperature grade, lifecycle, electrical ratings, and approved-part requirements for the controller.
When should I choose MAX3232EIDBR over MAX3232ECDB?
Choose MAX3232EIDBR when the assembly needs the documented ±15 kV IEC ESD-protected MAX3232E variant. MAX3232ECDB belongs to the closely related MAX3232EC family and may be considered when its temperature, availability, and electrical characteristics satisfy the design. Because device suffixes can encode meaningful differences, verify the exact ordering information rather than relying only on the shared SSOP footprint.
Is MAX3232EIDBR suitable for industrial serial consoles?
The MAX3232EIDBR is suitable for many industrial serial-console designs because it combines a 3 V to 5.5 V supply range with ±15 kV IEC ESD protection. Its 250 kbit/s maximum rate covers many diagnostic and asynchronous control protocols. The host system, connector, cable length, grounding method, and required temperature range should still be validated for the installation environment.
What is the best alternative-brand equivalent for MAX3232EIDBR?
The best alternative-brand equivalent must provide a genuine 16-pin SSOP pin-compatible RS-232 interface with comparable 3 V to 5.5 V operation and no more than 250 kbit/s. The available cross-reference results do not identify a validated cross-brand part with sufficient package and parameter detail, so no specific manufacturer is recommended as a drop-in substitute. Use the Request a Quote form on this page when sourcing an engineering-reviewed alternative.
Where to buy MAX3232EIDBR online?
MAX3232EIDBR can be requested through the Request a Quote form on this XAIPART page. The form supports direct sourcing without embedding a static price that may change with quantity or inventory. Include the required quantity, target reel or tube configuration, delivery location, and any automotive or industrial qualification requirements when submitting the request.
What is the price of MAX3232EIDBR?
The current commercial terms for MAX3232EIDBR are presented through the Request a Quote form on this page. Live unit and volume pricing can vary with quantity, packaging, and supply conditions, so use the form for the relevant configuration. The technical product record remains useful for comparing the MAX3232EIDBR with same-package alternatives based on function and electrical requirements.
What is the lead time and stock status for MAX3232EIDBR?
The current stock position and lead time for MAX3232EIDBR should be confirmed through the Request a Quote form on this page. Include your required quantity, delivery schedule, and acceptable packaging format in the request. Engineers should also verify the manufacturer lifecycle status when scheduling a long-running production program.
What are the key specifications of MAX3232EIDBR that engineers should know?
The key MAX3232EIDBR specifications are a 3 V to 5.5 V single supply, two RS-232 drivers, two receivers, a 250 kbit/s maximum data rate, a 30 V/µs maximum driver slew rate, and ±15 kV IEC ESD protection. The device uses a 16-pin SSOP package and requires four external charge-pump capacitors. Its internal charge pump eliminates the need for a separate negative supply.

Engineering reference data for MAX3232EIDBR — comparison, design guidance, and compliance information.

Selection Guide

Choose MAX3232EIDBR when the design needs a 16-pin SSOP dual RS-232 transceiver with a 3 V to 5.5 V single supply, operation up to 250 kbit/s, and documented ±15 kV IEC ESD protection. MAX3232ECDB is worth reviewing when the MAX3232EC family's protection and availability better match the assembly, but its exact ordering characteristics must be checked. MAX3232IDB is a close family candidate for an equivalent 16-pin SSOP design, with ESD rating and temperature grade requiring confirmation. MAX3232CAE+ may suit assemblies already standardized around that ordering code, provided its complete electrical specification is approved. In every case, verify the 16-pin SSOP footprint, charge-pump capacitor connections, truth table, temperature range, and connector wiring before production release.

Comparison with Alternatives

Parameter This Product MAX3232ECDB MAX3232IDB MAX3232CAE+
Package 16-pin SSOP 16-pin SSOP 16-pin SSOP 16-pin SSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments

Key Differentiators

  • Documented enhanced ESD protection (vs MAX3232IDB)
  • Single-rail interface operation (vs MAX3232CAE+)
  • Controlled cable transition rate (vs MAX3232ECDB)

Design Notes

Place the four charge-pump capacitors directly beside their associated IC pins, using the shortest practical traces and the ground connection shown in the manufacturer layout example. Keep RS-232 driver and receiver traces away from clocks, ADC signals, and switching-regulator nodes. Maintain a continuous signal-ground reference between the transceiver and connector, and route any chassis or surge-protection return current outside the sensitive interface ground path.

Do not treat a shared SSOP footprint as proof that every MAX3232-family ordering code is interchangeable. Before substituting MAX3232ECDB, MAX3232IDB, or MAX3232CAE+, compare the exact pin descriptions, temperature grade, supply limits, data rate, ESD rating, and receiver thresholds. Also confirm connector wiring and logic polarity against the datasheet truth tables; incorrect driver/receiver orientation is a common source of apparently dead communication links.

The MAX3232E limits driver output slew rate to 30 V/µs, but cable edges can still radiate when the board, connector, and ground return are poorly arranged. Use the shortest practical route from the IC to the connector, preserve adjacent return paths, and avoid splitting the ground plane beneath the interface. If the connector is exposed to a long external cable, evaluate a coordinated external surge-protection solution rather than increasing protection capacitance arbitrarily at the driver pins.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The manufacturer material confirms TIA/EIA-232-F operation and ±15 kV IEC ESD protection, but it does not state the requested environmental-compliance statuses. AEC-Q100 is not applicable to this unspecified commercial interface-device ordering option.

Related Searches

MAX3232EIDBR datasheet MAX3232EIDBR pinout MAX3232EIDBR datasheet pdf MAX3232EIDBR equivalent MAX3232EIDBR replacement MAX3232EIDBR drop-in replacement MAX3232EIDBR cross reference MAX3232EIDBR vs MAX3232CAE+ MAX3232EIDBR footprint MAX3232EIDBR price MAX3232EIDBR stock Texas Instruments MAX3232EIDBR

Related Components & Terms

Texas Instruments MAX3232EIDBR MAX3232E MAX3232ECDB MAX3232IDB MAX3232CAE+ RS-232 transceiver line driver line receiver interface IC semiconductor charge pump TIA/EIA-232-F IEC ESD protection 16-pin SSOP SSOP family surface mount SMD UART 250 kbit/s 3 V to 5.5 V supply 30 V/µs slew rate industrial serial console embedded UART bridge
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details