Products (44,000+)

MC33895FC - LIN Bus Transceiver | NXP | 32-QFN
MC33895FC

MC33895FC - LIN Bus Transceiver | NXP | 32-QFN

The NXP Semiconductors MC33895FC is a high-speed LIN bus transceiver packaged in a 32-QFN surface-mount package with an exposed pad. It serves as the interface between a LIN controller or host microcontroller and the physical LIN network, combining digital communication functions with the physical-layer circuitry required for reliable single-wire bus communication. The component is identified for automotive and industrial applications where a compact transceiver is needed to connect an embedded controller to a LIN network. A LIN transceiver is an interface IC within the broader automotive networking hierarchy. LIN, or Local Interconnect Network, is a low-cost, single-wire serial protocol commonly used for distributed vehicle subsystems and industrial control networks. The MC33895FC occupies the physical interface position between digital logic and the bus wiring, allowing higher-level firmware and controller hardware to exchange data through the LIN physical layer. The principal documented packaging characteristics are a 32-QFN case, surface mounting, and tube packing. A QFN package supports compact PCB layouts and exposes a pad beneath the device for thermal coupling to the board. The exposed pad is therefore an important layout feature rather than an additional electrical signal. Because the MC33895FC is intended for space-constrained automotive and industrial electronics, this package balances mechanical compactness with a practical thermal and assembly footprint. The MC33895FC is classified as a LIN transceiver, placing it within integrated interface semiconductors rather than processors, memory, or discrete communication components. Its system role requires compatibility with the LIN controller, microcontroller, bus termination strategy, supply architecture, and connector wiring of the target ECU or controller board. Designers should review the device documentation before assigning wake-up, fault-handling, supply, ground, and transceiver-enable functions to package pins. Typical uses include vehicle body and comfort electronics, sensor interfaces, local actuator controllers, industrial control modules, and distributed embedded systems. In each case, the transceiver supports communication over a LIN network while the attached controller handles protocol framing and application behavior. Its 32-QFN exposed-pad construction is useful where component density is important and board area is constrained. PCB implementation should place the transceiver close to the LIN connection and route the bus as a controlled single-wire network. Power and ground connections require careful layout according to the manufacturer pin description and recommended application circuit. The exposed pad should be connected using the prescribed land pattern and thermal strategy rather than treated as an interchangeable mechanical feature. This page combines the exact catalog identity, package information, sourcing references, application guidance, and selection considerations for MC33895FC. It is designed to help engineers move from part identification to datasheet review, footprint validation, interface design, and prototype assembly while avoiding unsupported electrical assumptions.

RFQ Contact
MC33897D - Single-Wire CAN Transceiver | NXP Semiconductors
MC33897D

MC33897D - Single-Wire CAN Transceiver | NXP Semiconductors

NXP Semiconductors MC33897D is a single-wire CAN transceiver, also known as an SWCAN physical-layer interface, designed for digital communication over a single-wire medium. The verified product information identifies a 1/1 transceiver configuration, 12 V supply rating, 83.33 Kbps data rate, 14-SOIC surface-mount package, and an operating temperature range of -40°C to +125°C. It is intended for automotive networks, industrial networks, farm equipment, marine systems, aircraft systems, and module-to-module communication. A single-wire CAN transceiver is a CAN bus physical-layer interface that uses one communication conductor rather than the separate transmit and receive conductors used by conventional CAN implementations. The MC33897D belongs to the broader CAN transceiver and interface IC category, providing the electrical interface between a digital controller and a single-wire CAN network. Its half-duplex operating concept supports communication over a shared network medium while reducing wiring complexity compared with dual-wire CAN. The key verified features of the MC33897D include its 1/1 driver and receiver arrangement, 12 V supply voltage, 83.33 Kbps data rate, and 14-SOIC package. The -40°C to +125°C operating range provides an extended temperature capability for demanding automotive, industrial, marine, and aircraft environments. The package is supplied in tube packaging according to the verified distributor information. MC33897D is a legacy NXP interface component associated with the Motorola 33897 family. The manufacturer datasheet identifies the product as a single-wire CAN transceiver providing the physical layer for digital communication using CSMA/CR operation over a single-wire medium. Because the device is listed as obsolete in the verified DigiKey search result, new production availability is not expected without a qualified sourcing route. The cross-reference data identifies MC33897CTEF as a parametric equivalent candidate. Typical uses include automotive body and module networks, agricultural machinery communications, industrial control networks, marine equipment, aircraft systems, and other installations requiring module-to-module communication over a reduced-wire-count bus. The 83.33 Kbps data rate and extended temperature range make the part relevant to legacy single-wire CAN designs, although system designers should confirm signal integrity, termination, grounding, and network topology against the manufacturer datasheet. When designing around MC33897D, pay particular attention to the single-wire bus topology and the 12 V supply requirement. The transceiver should be placed so that its connection to the one-wire network is physically short and properly controlled, with PCB layout and external components selected according to the datasheet. Obsolete status means sourcing continuity and counterfeit avoidance are important procurement considerations. This page combines verified manufacturer and distributor information, obsolete-lifecycle details, a documented parametric substitute, package and pinout status, and application-specific engineering guidance. It is intended to help engineers identify whether the legacy MC33897D remains electrically appropriate and how to verify a replacement before committing to a new design.

RFQ Contact
MC33897EF - 12V Single-Wire CAN Transceiver | NXP | 14-SOIC
MC33897EF

MC33897EF - 12V Single-Wire CAN Transceiver | NXP | 14-SOIC

NXP Semiconductors MC33897EF is a single-wire CAN physical-layer transceiver with one driver and one receiver, a nominal 12 V supply, and a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, in width. It provides the physical interface between a CAN controller and a single-wire CAN bus, allowing digital communication through a CSMA/CR data-link medium. A single-wire CAN transceiver is an interface IC that converts logic-level controller signals into the electrical signaling required by a single-wire CAN network. Its position in the hierarchy is transceiver → CAN interface IC → interface integrated circuit → semiconductor. This makes the MC33897EF suitable for automotive and industrial networks that use the single-wire CAN physical layer rather than conventional differential CAN. The device has a 1/1 driver-to-receiver configuration, supports the CAN protocol at its physical layer, and is supplied in a 14-SOIC package. Tube packaging is identified for the MC33897EF. Its lead-free status is identified by the manufacturer, although the complete environmental and qualification details should be confirmed against the relevant product documentation before a regulated design is released. As a bus interface, the MC33897EF isolates controller-side digital signaling from the physical bus and handles the required electrical conversion between the CAN controller and the wired medium. Designers should pay particular attention to bus termination, grounding, protection, and the distinction between the single-wire CAN signaling method and standard differential CAN implementations. Typical applications include vehicle body and comfort systems, distributed control modules, sensor interfaces, industrial automation equipment, and embedded diagnostic systems. In each case, a CAN controller handles protocol functions while the MC33897EF provides the physical-layer connection to the single-wire network. A successful implementation requires checking the controller interface voltage levels, bus topology, termination arrangement, and external protection strategy. The 14-SOIC outline facilitates conventional surface-mount assembly, while good grounding and short signal paths remain important for reliable communication in electrically noisy environments. This page consolidates the verified device identity, package information, interface configuration, sourcing pathway, comparison limits, and practical design guidance for engineers evaluating the MC33897EF. It also identifies where replacement qualification or additional electrical limits must be completed before schematic release.

RFQ Contact
MC33901WEF - 1Mbps High-Speed CAN Transceiver | NXP
MC33901WEF

MC33901WEF - 1Mbps High-Speed CAN Transceiver | NXP

NXP Semiconductors MC33901WEF is a SMARTMOS high-speed CAN transceiver that provides the physical interface between a microcontroller CAN controller and a physical dual-wire CAN bus. The device supports operation up to 1.0 Mbit/s and is packaged in an 8-pin SOIC with a market-standard pinout. MC33901WEF is identified as an automotive-grade component with AEC-Q100 qualification in distributor listings. A CAN transceiver is an interface circuit within the Controller Area Network hardware hierarchy. It converts logic-level signals from a CAN protocol controller into the differential voltage levels carried by the CAN bus, and converts received bus signals back into logic levels for the controller. The MC33901WEF family is designed for high-speed CAN networks requiring compact implementation, reliable bus signaling and protection against electrical transients. The MC33901WEF provides a maximum specified CAN data rate of 1.0 Mbit/s. Its 8-pin SOIC package supports compact PCB placement, while the market-standard pin arrangement helps simplify replacement and board-layout planning. The component is listed with 5 V operation, normal and standby operating modes, automotive temperature grading and AEC-Q100 qualification. Manufacturer information also describes excellent EMC and ESD performance without requiring external filter components. The SMARTMOS implementation is intended to provide efficient CAN physical-layer operation in industrial, automotive and embedded networking systems. Because the transceiver is the interface between digital controller logic and the physical bus, correct supply decoupling, termination and signal-integrity layout are essential. The SOIC package should be placed close to the CAN connector and the bus differential pair, with protection components positioned where they can divert surge and ESD energy without disrupting the signal path. Typical applications include automotive CAN networks, industrial automation equipment, robotics, building controls, embedded motor-control systems and other distributed electronic systems that require a physical CAN interface. In these systems, the MC33901WEF allows the host MCU or dedicated CAN controller to communicate over the two-wire differential bus while keeping the physical-layer implementation compact. Designers should verify the complete transceiver operating temperature range, supply tolerances, loop-delay limits, bus fault handling and pin-level behavior against the current manufacturer datasheet before release. The CAN bus must also use the correct 120-ohm termination arrangement, and unused or unused-mode pins should follow the datasheet requirements rather than being left open by assumption. The package and exposed electrical requirements should be checked against the PCB footprint and assembly process. This page combines the manufacturer’s MC33901 family information, exact MPN listings, package details, replacement discussion and practical integration guidance. It is intended to help engineers identify the correct CAN transceiver, understand its physical-layer role and plan a compatible replacement before committing the 8-pin SOIC footprint to a PCB.

RFQ Contact
MC33972DWBR2 - 22-Ch Switch Detection MSDI, SPI, 32-SOIC | NXP
MC33972DWBR2

MC33972DWBR2 - 22-Ch Switch Detection MSDI, SPI, 32-SOIC | NXP

The NXP MC33972DWBR2 is a Multiple Switch Detection Interface (MSDI) with suppressed wake-up, monitoring up to 22 switch contacts and reporting status to an MCU over an SPI serial interface. Packaged in a 32-pin SOIC (0.295 inch / 7.50 mm body width) and supplied from 3.1 V to 5.25 V, the part integrates a 22-to-1 analog multiplexer and operates in Normal mode (programmable, full switch monitoring) or Sleep mode (low quiescent current) to support always-on automotive and industrial body electronics. A Multiple Switch Detection Interface is a type of switch-monitoring IC that scans many discrete contact closures (e.g., door, seat, latch, and button inputs) and reports either binary open/closed states or a selected analog channel voltage through a digital interface. The MC33972 belongs to the interface-IC product family (specialized) within digital logic and serial-interface semiconductors, and is widely used in body control modules, gateway ECUs, and industrial equipment where contact wetting current, debounce, and wake-up are critical. Key features include 22 switch inputs with programmable wet/dry configuration, integrated 22:1 analog MUX output, an SPI-compatible slave interface, programmable wetting current, switch-state-change interrupt with wake-up capability, and a Sleep mode quiescent current designed for ultra-low standby budgets in vehicle quiescent-current specifications. The device contains an analog multiplexer, programmable current sources, an SPI controller, an internal voltage regulator, a wake-up timer, and an interrupt generator. The internal architecture allows each of the 22 input pins to source (or sink) a wetting current and to be read back through the analog MUX; this eliminates the need for dozens of discrete pull-ups and reduces PCB area significantly compared to discrete solutions. Typical applications include automotive body control modules (reading door/trunk/hood switches), industrial control panels with many contact inputs, agricultural and construction equipment dashboards, and any system that needs to wake an MCU from Sleep on a switch event with very low standby current. The MC33972 is also a strong fit for HVAC and appliance controls that aggregate a large number of mechanical switches. When designing with this part, ensure the supply rail is decoupled with a 0.1 uF ceramic close to VDD and that the analog MUX output is buffered if multiple devices share the same MCU ADC channel. Take care with PCB layout to keep switch-return paths near ground, and follow NXP's application guidance on wetting-current programming to balance contact reliability against continuous dissipation. This page synthesizes NXP datasheet specifications, distributor pricing snapshots, drop-in alternative sourcing (same-package SPI MSDI devices), and practical layout notes not gathered on a single manufacturer page.

RFQ Contact
MC33972EW - 22-Channel Switch Detection Interface | NXP
MC33972EW

MC33972EW - 22-Channel Switch Detection Interface | NXP

The NXP Semiconductors MC33972EW is a multiple switch detection interface with suppressed wake-up, designed to detect opening and closing events for as many as 22 switch contacts. The device transfers switch status to a microprocessor or microcontroller through a serial peripheral interface, while its 22-to-1 analog multiplexer supports reading the switch inputs as analog signals. It is packaged in a 32-pin SOIC. A multiple switch detection interface is an interface IC used to consolidate many discrete switch inputs into a controlled communication link. It sits between mechanical or resistive switch contacts and the host controller, reducing the number of host input pins and providing a structured way to monitor multiple states. In the hierarchy of electronic components, this device is an interface IC within the broader semiconductor and embedded-control ecosystem. The principal feature of the MC33972EW is support for up to 22 switch contacts. Open or closed status information is transferred through the SPI interface, allowing the host processor to read the switch bank efficiently. The integrated 22-to-1 analog multiplexer also allows the same input array to be examined as analog information. This dual-purpose architecture can simplify firmware and hardware in systems where the same contacts provide either discrete status or a resistance-based measurement. Suppressed wake-up is another defining function. It is intended for systems that must avoid unnecessary wake-up activity from switch changes, helping the host distinguish relevant events from routine contact activity. The precise thresholds, timing behavior, and implementation details should be configured using the manufacturer datasheet and the host firmware requirements. Typical applications include automotive switch and body-control systems, instrument-panel interfaces, control-panel monitoring, industrial equipment, and embedded systems that need to scan many switch contacts. The SPI host connection makes the device suitable for centralized input conditioning rather than dedicating one microcontroller pin to every switch. When designing around the MC33972EW, account for the host SPI mode, chip-select behavior, wake-up logic, and the electrical characteristics of the connected switches. Place the interface close enough to the switch network to minimize analog-input sensitivity to board-level noise. Review the pin-description table and recommended application circuit in the NXP datasheet before assigning PCB nets or selecting external components. This product page combines the MC33972EW functional description, package information, sourcing guidance, verified-source references, and practical design considerations. It also distinguishes directly documented capabilities from engineering details that should be confirmed in the current manufacturer documentation before layout release.

RFQ Contact
MC33975EK - 22-Channel Switch Detection SPI Interface | NXP
MC33975EK

MC33975EK - 22-Channel Switch Detection SPI Interface | NXP

The NXP MC33975EK is a multiple switch detection interface with suppressed wake-up and 32 mA wetting current, housed in a 32-BSSOP (0.295 in / 7.50 mm width) exposed-pad package. It monitors up to 22 switch contacts and reports open/closed state to a host MCU through a serial peripheral interface (SPI). The suppressed wake-up feature prevents battery drain by ignoring transient switch events during sleep. A Multiple Switch Detection Interface (MSDI) is a mixed-signal ASIC that integrates analog wetting-current sources, comparator inputs, an SPI slave, and an interrupt generator into one IC. It sits in the body-and-chassis electrical architecture between mechanical switches and the body control module (BCM), replacing dozens of discrete pull-ups, diodes, and MCU GPIO resources. In the broader taxonomy it is an SPI interface, a peripheral IC, an interface IC, and a power-management-adjacent analog/mixed-signal semiconductor. Key features include detection of 22 switch contacts, configurable wetting current of 2 mA or 20 mA, programmable wake-up behavior to ignore short transients, SPI communication up to 8 MHz max, on-chip input debouncing, and a low quiescent current in sleep mode. The exposed thermal pad on the 32-BSSOP package reduces thermal resistance, supporting extended automotive temperature operation. Internally the 33975 uses a current source array feeding each input pin, comparators with programmable thresholds, an SPI-compatible slave with a hardware interrupt, and a wake-up filter that suppresses brief mechanical contact bounce. The 32 mA peak wetting current capability lets it handle both wet and dry switch contacts, including those carrying inductive loads. Typical applications include automotive body control modules detecting door, hood, trunk and seat switches, vehicle occupant detection, climate-control switch matrixes, steering wheel button reading, and any system that must poll many mechanical switches reliably over SPI. When designing with the 33975, ensure the VBAT supply is well decoupled and that the exposed pad is soldered to a sufficient copper pour for thermal relief. The suppressed wake-up timer should be tuned to the mechanical bounce profile of the specific switch family used. This page consolidates distributor inventory, SPI-based drop-in alternatives from the same and competing manufacturers, and practical automotive EMC guidance that goes beyond the manufacturer datasheet bullet list.

RFQ Contact
MC33978ES - 22-Channel Switch Detection Interface | NXP
MC33978ES

MC33978ES - 22-Channel Switch Detection Interface | NXP

NXP Semiconductors MC33978ES is a 22-channel multiple switch detection interface with programmable wetting current, an SPI interface to the host processor, and a 32-QFN-EP package measuring 5 mm by 5 mm. Designed for automotive switch-contact monitoring, it consolidates multiple switch inputs into a serial interface that reduces wiring and processor pin requirements. A multiple switch detection interface is an interface IC within the broader automotive semiconductor and input-signal-control hierarchy. It detects whether external switch contacts are open or closed and transfers their states to a microcontroller or other host controller. By centralizing contact monitoring and supporting programmable wetting current, this device class is intended to support robust operation across vehicle electrical environments. The MC33978ES provides 22 switch-detection channels, selectable wetting-current behavior, and serial data transfer through SPI. The NXP manufacturer datasheet identifies the device as a 22-channel multiple switch detection interface with programmable wetting current. Programmable wetting current gives the system designer control over the excitation applied to switch contacts, which can help maintain reliable state detection when contacts are affected by contamination, aging, or resistive leakage paths. The SPI connection provides a compact mechanism for transferring switch status to the host electronics instead of requiring one dedicated processor input per switch. The 32-QFN-EP package also includes an exposed thermal pad for board-level heat spreading. Its 5 mm by 5 mm footprint supports dense automotive electronic-control-unit layouts while keeping the number of external interconnects low. Typical uses include vehicle door, window, seat, hood, trunk, and latch-contact monitoring, as well as body and comfort-system switch consolidation. The device can also serve in other 12 V vehicle electrical systems where multiple discrete inputs must be checked reliably. In these applications, the MCU periodically reads the switch status and can identify state changes for lighting, locking, diagnostics, or fault reporting. When laying out the PCB, use the manufacturer pin-description table and exposed-pad land pattern exactly. Place the interface close to the switched inputs to minimize vulnerable trace length, provide a low-impedance return path, and route SPI signals away from high-current or inductive vehicle systems. Confirm the programmed wetting-current setting against the switch-contact resistance and the vehicle’s electrical requirements. This page combines the manufacturer’s device description with package information, replacement guidance, comparison criteria, and practical PCB considerations. It is intended to help engineers determine whether the MC33978ES fits a switch-monitoring design and how to evaluate compatible options without confusing a functional alternative with a verified drop-in replacement.

RFQ Contact
MC33989DW - Automotive CAN System Basis Chip | NXP
MC33989DW

MC33989DW - Automotive CAN System Basis Chip | NXP

The NXP Semiconductors MC33989DW is an automotive system basis chip with a high-speed CAN physical interface, integrated into a 28-SOIC package. Its three headline characteristics are a 5.5 V to 18 V supply range, CAN operation up to 1.0 Mbaud, and an SPI interface for connection to a microcontroller. The device also combines two voltage regulators, four high-voltage wake-up inputs, VSUP monitoring, and fault-detection circuitry. A system basis chip, or SBC, is an interface IC that consolidates functions normally distributed around a microcontroller in an automotive electronic control unit. Its position in the hierarchy is SBC → CAN interface IC → interface IC → semiconductor. Integrating power regulation, bus physical-layer functions, wake-up detection, and supply supervision reduces the component count and board area needed around the host microcontroller while preserving a structured diagnostic and control interface. The MC33989DW combines a 1.0 Mbaud-capable CAN physical interface with an SPI host interface. Four high-voltage wake-up inputs allow the device to detect external wake events in an automotive environment. Two internal voltage regulators support the host power architecture, while VSUP monitoring and fault-detection circuitry provide supply-state supervision. These functions make the device suitable for compact ECU subsystems that require more than a standalone CAN transceiver. Automotive electronics commonly separate a low-power communication domain from the main MCU supply domain. MC33989DW supports this architecture by combining a regulated supply path, CAN physical signaling, and wake-up detection in one package. The SPI connection gives the host processor access to control and status functions without requiring a separate external CAN controller. Because the device also performs supply monitoring, designers can base early-startup and fault-handling decisions around a dedicated system basis component. Typical uses include body and comfort controllers, engine-control subsystems, transmission controllers, sensor nodes, and other automotive modules using CAN communication. It is also relevant to industrial or transportation equipment where a ruggedized supply range, local wake-up detection, and a high-speed CAN physical interface simplify the implementation around a microcontroller. When laying out the circuit, place the device and its support components according to the pin-description and recommended-layout sections in the NXP manufacturer datasheet. Confirm the complete 28-pin mapping, supply decoupling requirements, CAN transceiver connection details, and external component values before releasing the PCB; the MC33989DW integrates several subsystems whose layout decisions can affect signal integrity and startup behavior. This page organizes the MC33989DW electrical ratings, package information, practical design guidance, application fit, and verified drop-in replacement status. It also distinguishes a true pin-compatible replacement from a merely similar CAN transceiver so procurement and engineering teams can avoid assuming that a different package or architecture is electrically interchangeable.

RFQ Contact
MC33989DWR2 - System Basis Chip with High-Speed CAN | NXP
MC33989DWR2

MC33989DWR2 - System Basis Chip with High-Speed CAN | NXP

The NXP MC33989DWR2 is a System Basis Chip (SBC) integrating a high-speed CAN (Controller Area Network) transceiver with a 5V/3.3V voltage regulator, watchdog timer, SPI interface, and high-side/low-side drivers in a single 28-pin SOIC package. It targets automotive Engine Control Units (ECUs) and other in-vehicle network nodes requiring a compact, mixed-signal power-and-communication front-end. A System Basis Chip is a category of automotive-grade mixed-signal IC that consolidates the discrete building blocks surrounding a microcontroller into a single die. Sitting between the 12V vehicle bus and the MCU, an SBC provides a regulated supply rail, bus transceiver (typically CAN or LIN), diagnostic monitoring, and protection functions. This consolidation reduces PCB area, simplifies EMC design, and improves overall reliability versus discrete implementations. Key features of the MC33989DWR2 include an ISO 11898-compliant high-speed CAN transceiver supporting up to 1 Mbit/s bus speeds, a 5V LDO regulator with selectable 3.3V mode for MCU power, an integrated watchdog with selectable window timeout, a SPI configuration port for diagnostic and control, and two low-side drivers plus a high-side driver for sensor or actuator switching. The device operates across a 5.5V to 27V supply range with transient tolerance typical of automotive 12V powernet environments. Internal architecture combines a bipolar/CMOS mixed process for the power stages with a CMOS logic section for the digital SPI/watchdog core. The CAN transceiver includes bus pin protection to +/- 8 kV HBM ESD and dominant-timeout logic to prevent bus lockup during software faults. Typical applications include automotive ECUs, body controllers, gateway modules, and industrial CAN nodes. The automotive design tip requires placing a reverse-polarity protection diode on VBAT, a 100 nF decoupling capacitor on VCC, and a CAN bus filter circuit with two 60 ohm termination resistors split across a 120 ohm center tap to maximize signal integrity. This page synthesizes distributor pricing from DigiKey, Mouser and Octopart, drop-in pin-compatible alternatives qualified on the 28-SOIC footprint, and practical design notes beyond what the manufacturer datasheet alone provides for a 12V automotive CAN node.

RFQ Contact
MC33990D - Technical Component Data | NXP Semiconductors
MC33990D

MC33990D - Technical Component Data | NXP Semiconductors

The NXP Semiconductors MC33990D is an integrated circuit whose verified manufacturer specifications, package details, electrical ratings, and lifecycle status were not available in the supplied 2026-10-29 research dataset. The source request returned an engine circuit-breaker error, and no internal database record or alternatives cross-reference result was supplied. Consequently, this page does not infer voltage, current, speed, interface, temperature, pinout, or compliance values that cannot be authenticated. The verified record identifies the manufacturer part number as MC33990D and the associated manufacturer as NXP Semiconductors. Its closest catalog category is Interface ICs, where communication interface devices provide the physical signaling layer between digital controllers and external buses or networks. A final component-selection decision requires the current manufacturer datasheet and product-page information. What is an Interface IC? An Interface IC is a semiconductor in the interface IC category that converts, conditions, buffers, or controls signals between a host processor and external equipment. Interface ICs can support communication buses, isolation functions, level conversion, transceivers, voltage references, and protocol-specific links. Because MC33990D interface, electrical, timing, and package details are unavailable in the supplied evidence, selecting it for a specific bus, voltage domain, data rate, automotive environment, or PCB land pattern would otherwise risk an invalid design assumption. The principal verified limitation is data completeness rather than a confirmed technical weakness. The only usable identifiers are the MPN MC33990D, the NXP Semiconductors brand assignment, and the 2026-10-29 retrieval date. No manufacturer datasheet URL, package designation, pin map, absolute maximum ratings, recommended operating conditions, electrical characteristics, timing values, environmental ratings, qualification status, or lifecycle classification appears in the provided records. Those parameters therefore remain explicitly unresolved rather than being populated from memory or a non-verified secondary listing. Typical use cannot be validated from the supplied evidence, so this page does not claim that MC33990D is intended for automotive networking, industrial control, communications, or another specific application. Engineers should first confirm the exact function, package drawing, pin-compatible land pattern, operating limits, and ordering configuration from the current NXP documentation. The empty alternative list is intentional because the supplied cross-reference search returned no results; proposing an MPN as pin-to-pin compatible without a verified package and parameter comparison would be misleading. The key design consideration is to avoid treating the absence of retrieved specifications as evidence of universal applicability. Verify the manufacturer datasheet, errata, package information, lifecycle status, and qualification markings before schematic capture or PCB layout. Check every pin name, exposed-pad requirement, recommended decoupling, electrical limits, and timing condition against the exact ordering code. Obtain written lifecycle confirmation when production continuity matters. This page uniquely separates verified identifiers from unverified technical assumptions and exposes every unresolved field. It also records the failed retrieval timestamp, the absence of usable source URLs, and the reason no drop-in alternatives, complete pinout, safe operating area, package drawing, or price tiers can be authenticated. That transparency gives procurement and engineering teams a reliable evidence boundary while directing them to the current manufacturer documents for procurement and design release.

RFQ Contact
MC33990DR2 - 10.4 kbps J1850 Transceiver | NXP
MC33990DR2

MC33990DR2 - 10.4 kbps J1850 Transceiver | NXP

The NXP Semiconductors MC33990DR2 is a half-duplex J1850 serial transceiver for automotive Class B data networks, operating at 10.4 kbps from a 9 V to 16 V supply in an 8-pin SOIC package. It combines a transmitter, receiver, and bus interface in one device, providing bidirectional communication over a shared vehicle network. An automotive serial transceiver is an interface IC that converts logic-level signals into a physical bus waveform and reconstructs valid receive data from that waveform. The MC33990DR2 belongs to the line-driver and receiver hierarchy, where it connects an automotive controller or ECU to a J1850 network while handling the voltage levels, bus contention, and noise characteristic of vehicle wiring. SAE J1850 Class B is the network specification identified for this device. The principal operating characteristics are a 10.4 kbps data rate, a 9 V to 16 V supply range, and 200 mV receiver hysteresis. The 200 mV hysteresis helps the receiver distinguish signal states when noise or slow transitions appear on the bus. Its single half-duplex transceiver arrangement allows the same bus connection to transmit and receive, although software or hardware must ensure that only one node drives the network at a time. The MC33990DR2 is packaged in an 8-pin SOIC for surface-mount assembly and is identified as an automotive-temperature-grade part. Its principal role is to provide a compact physical-layer interface between an automotive electronic control unit and a J1850 Class B network. The half-duplex topology supports body and powertrain systems where distributed modules share a low-speed diagnostic or communication backbone. Typical uses include powertrain control modules, body control modules, instrument clusters, engine controllers, and vehicle diagnostic interfaces. In these systems, the transceiver can carry messages between ECUs while providing stronger signal conditioning than a general-purpose logic interface. Its dedicated network function reduces the need for separate transmit and receive circuitry at the ECU. Design the bus connection with the recommended network termination, protection, and decoupling arrangements from the NXP datasheet. Because vehicle networks can experience transients and wiring faults, verify the external protection network, logic-level compatibility, and grounding strategy rather than relying only on the IC's operating-voltage range. The 8-pin SOIC footprint also requires adequate copper spacing and thermal consideration for automotive temperature conditions. This product page combines the device's electrical operating limits with application guidance, practical interface considerations, a qualified comparison framework, and sourcing information for engineers designing a J1850 Class B node.

RFQ Contact
MC33993DWBR2 - 22-Ch Switch Detection Interface | NXP
MC33993DWBR2

MC33993DWBR2 - 22-Ch Switch Detection Interface | NXP

The NXP MC33993DWBR2 is a Multiple Switch Detection Interface (MSDI) IC that monitors the closing and opening of up to 22 switch contacts, housed in a 32-pin SOIC Wide (SOIC W / DWB) package with tape-and-reel packaging and AEC-Q100 automotive qualification. It supports a supply voltage range of 5.5V to 26V (with 4.5V to 5.5V compatibility via SPI configuration), and communicates with the host MCU through an SPI (Serial Peripheral Interface) bus up to 8 MHz. A Multiple Switch Detection Interface (MSDI) is a type of specialized automotive interface IC that scans multiple mechanical or electronic switch inputs and reports their state to a microcontroller. It belongs to the broader hierarchy of interface ICs -> communication ICs -> automotive semiconductors, and is engineered to replace discrete pull-ups and multiplexing circuits with a single robust solution. This category of IC dramatically reduces wiring harness complexity in body control modules by allowing many switches to share a common return path. Key features include 22 input channels with programmable wetting current (typically 1 mA, 6 mA, or 16 mA selectable via SPI), built-in debounce timers, an analog-to-digital mode for ratiometric measurement, an interrupt output to wake the host MCU on state change, and robust automotive transient immunity. The 32-pin SOIC W (DWB) package supports -40C to +125C automotive operating temperature range and is qualified per AEC-Q100 standards. The MC33993 uses a sequential scanning architecture where each switch input is multiplexed through an internal analog front-end, then compared to programmable thresholds. The SPI register map provides status, configuration, and interrupt control. Two programmable wetting current sources ensure reliable operation with both dry-contact and electronic switches by preventing contact oxidation. Typical applications include automotive body control modules for window switches, door lock and mirror controls, steering wheel button clusters, HVAC control panels, and seat adjustment switches. The device replaces discrete resistor networks and dozens of MCU pins, freeing the host processor for higher-level functions while maintaining low quiescent current (<=100 uA typical standby). When designing with this part, ensure the SPI master clock does not exceed 8 MHz and configure wetting current to match the switch contact type. For battery-connected applications, add reverse-battery and load-dump protection per system requirements. This page synthesizes drop-in alternatives, parametric comparison data, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MC34018DW - Voice-Switched Speakerphone IC | NXP | 28-SOIC
MC34018DW

MC34018DW - Voice-Switched Speakerphone IC | NXP | 28-SOIC

NXP Semiconductors MC34018DW is a voice-switched speakerphone integrated circuit designed for telephone-line communication equipment. It provides a 5.4 V supply rating, 9 mA supply current, 100 mW power dissipation, and a 35 dB speech network standard in a 28-pin SOIC package. The device is listed as obsolete and targets legacy telephony designs rather than new voice-over-IP products. A voice-switched speakerphone circuit is an analog telephone interface that activates the microphone during speech and transfers audio to the loudspeaker when the remote party talks. It prevents local transmitted speech from being reproduced through the speaker, reducing acoustic feedback while allowing hands-free conversation. In the system hierarchy, the MC34018DW is a telecom interface IC, a voice-network analog front end, and an integrated application-specific semiconductor. The MC34018DW integrates the switching and speech-network functions needed for a compact telephone speakerphone. Its principal characteristics include one internal circuit, a 5.4 V nominal supply, approximately 9 mA supply current, and an operating-temperature range of -20 °C to +60 °C. These ratings identify the part as a commercial-grade, legacy line interface intended for telephone handsets, analog desk phones, and related communications equipment. The 28-pin SOIC construction supports conventional surface-mount assembly while providing separate connections for microphone, speaker, line, and control functions. The commercial temperature range accommodates standard indoor telecom equipment but not extended automotive or industrial environments. The reported 100 mW dissipation is modest, making copper heat spreading generally less important than correct analog routing and protection around the telephone line. Typical uses include analog corded telephones, speakerphone terminals, telephone answering equipment, and legacy two-wire line interfaces. Because the MC34018DW is obsolete, new designs should normally evaluate current speech-processing or telephone-interface ICs instead of creating a new dependency on this legacy device. Existing production equipment can benefit from careful footprint, pin-function, and lifecycle review before selecting a replacement. For a drop-in substitution, engineers must verify the complete 28-pin schematic, microphone and speaker biasing, line-interface topology, supply tolerances, control thresholds, and thermal conditions. A similar speech-network function alone does not establish pin-to-pin compatibility. The manufacturer datasheet remains the controlling reference for connection details and application limits. This page organizes the documented MC34018DW characteristics, practical telecom use cases, sourcing information, and replacement-selection guidance. It also distinguishes verified drop-in alternatives from merely related voice-processing parts so engineers can avoid PCB respin or unexpected control-interface changes.

RFQ Contact
MC3403D - Quad 30 V 1 MHz Op Amp | Texas Instruments
MC3403D

MC3403D - Quad 30 V 1 MHz Op Amp | Texas Instruments

The Texas Instruments MC3403D is a quad, general-purpose bipolar operational amplifier built for single-supply and dual-supply analog systems. The device provides four amplifiers in a 14-SOIC package, operates from ±2.5 V to ±15 V according to the cited distributor specification, and supports a 1 MHz gain-bandwidth product. Its four-circuit integration reduces package count while providing true differential inputs and push-pull output capability. What is a quad operational amplifier? A quad operational amplifier combines four independent amplifier sections in one IC. These amplifiers serve as the active gain elements in sensors, buffers, analog filters, comparators, and feedback-control circuits. The MC3403 belongs to the operational-amplifier hierarchy, which is part of the broader amplifier-IC and signal-conditioning categories used in industrial control, instrumentation, audio, and communications equipment. Key verified features include four amplifier circuits, 1 MHz operation, 0.6 V/µs slew rate, a 14-pin SOIC package, and operation from −25 °C to 85 °C. The push-pull output stage supports bidirectional output-current drive in suitable loads, while the quad configuration gives designers four reusable analog channels in one package. These attributes make the MC3403D practical for low-to-moderate-frequency analog signal paths where four similar amplifier functions are required. The MC3403’s electrical characteristics are described as similar to the popular UA741 family, but its architecture is specifically useful in single-supply applications. Compared with a basic dual-supply-only op amp, the part offers a practical path to operating from a single rail in many circuits. Designers must still check input common-mode limits, output swing, supply current, noise, offset behavior, and stability against the manufacturer datasheet for the exact operating condition. Typical uses include sensor buffering, low-frequency active filtering, audio preamplification, transducers, analog control loops, and general instrumentation. For a new design, confirm the required input and output voltage ranges, acceptable slew rate, load impedance, noise performance, and temperature limits. For a replacement, verify the exact pinout, supply range, common-mode range, and output-swing requirements rather than relying only on the amplifier count. A key practical consideration is decoupling. Place the required supply bypass capacitors close to the power pins and keep sensitive input and feedback traces short. The MC3403D is a general-purpose amplifier, not a precision or high-speed device; use a more specialized amplifier when low offset, low noise, high speed, rail-to-rail operation, or extended temperature performance is mandatory. This page consolidates verified manufacturer and distributor information, drop-in alternatives, application guidance, package details, and selection considerations for engineers evaluating MC3403D. It is intended to support procurement and design review without substituting unsupported specifications for missing datasheet data.

USD $0.41 In Stock
MC3403DG - Quad 1MHz Op Amp, 3-36V | onsemi
MC3403DG

MC3403DG - Quad 1MHz Op Amp, 3-36V | onsemi

onsemi MC3403DG is a quad general-purpose operational amplifier with true differential inputs, a 3 V to 36 V supply range, 1 MHz gain-bandwidth product, and a 14-pin SOIC package. It provides four amplifiers in one package and is designed for single-supply signal-conditioning, buffering, filtering, current-sensing, analog measurement, and precision-control circuits. An operational amplifier, or op amp, is a voltage-amplified differential building block whose open-loop gain falls with frequency. The MC3403 family belongs to the broader hierarchy of analog amplifier ICs used to amplify small differential signals, buffer high-impedance sources, implement active filters, and close feedback loops around sensors or actuators. Its true differential inputs make the device particularly useful when a useful output must follow the difference between two input voltages rather than either input alone. The quad configuration provides four amplifiers in one 14-pin SOIC, reducing board area and simplifying multi-channel designs. Key characteristics include operation from 3 V to 36 V, a 1 MHz gain-bandwidth product, and a maximum input offset voltage of 10 mV as listed by Mouser. The part is identified as a standard general-purpose amplifier and is suitable for instrumentation, buffer-amplifier, measurement, filtering, and precision-control applications. Its single-supply capability is particularly useful in cost-sensitive systems where one supply rail must support the complete analog signal chain. Differential inputs allow subtraction, current-loop monitoring, sensing across resistive elements, and amplification of sensor outputs without external input networks. Because the package contains four amplifiers, designers can use matched functional channels for simultaneous acquisition, multi-axis sensing, or multiple filter stages while preserving consistent board organization. Typical uses include 4-20 mA process-control inputs, resistive sensor conditioning, active low-pass or band-pass filters, buffered sensor outputs, general-purpose instrumentation, and current-shunt measurements. The 3 V minimum supply supports modern 3.3 V systems, while the 36 V maximum provides additional headroom for industrial supply rails. Commercial-temperature operation is identified in distributor listings, although the exact temperature limits require confirmation from the manufacturer datasheet. When laying out a MC3403DG circuit, place input, feedback, and compensation components close to the relevant SOIC pins and provide adequate return paths for each amplifier channel. Decoupling capacitors should connect between the supply pins and ground with short traces, and unused amplifier inputs should be tied to a defined potential rather than left floating. Check output-current, input-common-mode, noise, and stability requirements against the complete operating conditions before finalizing the design. This product page combines verified manufacturer and distributor information, a complete 14-pin pinout, practical single-supply design guidance, and a parameter-based comparison with available 14-pin quad amplifier alternatives. It also distinguishes confirmed electrical characteristics from parameters that still require verification in the manufacturer datasheet.

RFQ Contact
MC3403DR - Quad 30 V 1 MHz Op Amp | Texas Instruments (Tape & Reel)
MC3403DR

MC3403DR - Quad 30 V 1 MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments MC3403DR is a quad, general-purpose bipolar operational amplifier built for single-supply and dual-supply analog systems. The device provides four amplifiers in a 14-SOIC package, operates from ±2.5 V to ±15 V according to the cited distributor specification, and supports a 1 MHz gain-bandwidth product. Its four-circuit integration reduces package count while providing true differential inputs and push-pull output capability. What is a quad operational amplifier? A quad operational amplifier combines four independent amplifier sections in one IC. These amplifiers serve as the active gain elements in sensors, buffers, analog filters, comparators, and feedback-control circuits. The MC3403 belongs to the operational-amplifier hierarchy, which is part of the broader amplifier-IC and signal-conditioning categories used in industrial control, instrumentation, audio, and communications equipment. Key verified features include four amplifier circuits, 1 MHz operation, 0.6 V/µs slew rate, a 14-pin SOIC package, and operation from −25 °C to 85 °C. The push-pull output stage supports bidirectional output-current drive in suitable loads, while the quad configuration gives designers four reusable analog channels in one package. These attributes make the MC3403DR practical for low-to-moderate-frequency analog signal paths where four similar amplifier functions are required. The MC3403’s electrical characteristics are described as similar to the popular UA741 family, but its architecture is specifically useful in single-supply applications. Compared with a basic dual-supply-only op amp, the part offers a practical path to operating from a single rail in many circuits. Designers must still check input common-mode limits, output swing, supply current, noise, offset behavior, and stability against the manufacturer datasheet for the exact operating condition. Typical uses include sensor buffering, low-frequency active filtering, audio preamplification, transducers, analog control loops, and general instrumentation. For a new design, confirm the required input and output voltage ranges, acceptable slew rate, load impedance, noise performance, and temperature limits. For a replacement, verify the exact pinout, supply range, common-mode range, and output-swing requirements rather than relying only on the amplifier count. A key practical consideration is decoupling. Place the required supply bypass capacitors close to the power pins and keep sensitive input and feedback traces short. The MC3403DR is a general-purpose amplifier, not a precision or high-speed device; use a more specialized amplifier when low offset, low noise, high speed, rail-to-rail operation, or extended temperature performance is mandatory. This page consolidates verified manufacturer and distributor information, drop-in alternatives, application guidance, package details, and selection considerations for engineers evaluating MC3403DR. It is intended to support procurement and design review without substituting unsupported specifications for missing datasheet data.

USD $0.41 In Stock
MC3403DT - Quad 36V 1MHz Op Amp IC | STMicroelectronics
MC3403DT

MC3403DT - Quad 36V 1MHz Op Amp IC | STMicroelectronics

The STMicroelectronics MC3403DT is a low-cost, low-power quad bipolar operational amplifier with four true differential amplifier sections, a 1 MHz gain-bandwidth product, and single-supply operation from 3 V to 36 V. The device is packaged in a 14-pin SOIC and can also operate from dual supplies of ±18 V. Its short-circuit-protected outputs, internally compensated Class AB output stages, and input bias current of 500 nA maximum make it suitable for general-purpose analog signal conditioning. An operational amplifier is an amplifier IC that compares two input voltages and drives its output to represent their difference. A differential input stage rejects common-mode signals, while internal frequency compensation simplifies closed-loop design. The MC3403 combines four amplifiers in one package, placing it in the hierarchy of quad op amp, operational amplifier, analog amplifier IC, and semiconductor. Its broad supply range also makes it a bridge between classic 741-class circuitry and newer low-voltage single-supply systems. Key features include four independent amplifier channels, true differential inputs, 1 MHz gain-bandwidth performance, operation down to a 3 V single supply, and operation up to a 36 V single supply. Each output stage uses a Class AB topology for reduced crossover distortion, while short-circuit protection improves robustness when an output is driven into a difficult load. The internally compensated design supports direct use as a voltage follower or noninverting amplifier without external frequency-compensation components. The MC3403 family combines the general-purpose behavior of the UA741 with lower supply-current demand and improved suitability for single-supply operation. Each channel presents differential inputs, allowing signals to be referenced around the supply midpoint in single-supply circuits. Because the amplifiers are not rail-to-rail, input and output common-mode limits remain important when the signal approaches either supply rail. Designers should use the manufacturer data sheet for exact electrical limits, input-offset voltage, slew rate, output-current capability, and channel-matching characteristics. Typical uses include sensor-signal conditioning, low-frequency active filters, instrumentation amplifiers, audio preamplifiers, transducers, analog control loops, and general instrumentation. Four amplifiers in one package can implement a complete filter, multi-stage gain block, comparator-style signal conditioning, or several independent channels when board area and component count are priorities. The SOIC-14 package also supports conventional through-hole PCB assembly rather than requiring a fine-pitch surface-mount land pattern. When designing around the MC3403DT, begin with the required input and output common-mode range at the actual supply voltage. Place supply-bypass capacitors near the device, maintain a stable reference point for single-supply signals, and verify stability for the selected gain, load, and feedback network. Avoid relying on rail-to-rail operation, and check the maximum total supply voltage when combining bipolar or dual-supply systems. This product page combines the manufacturer operating limits, package information, sourcing details, pin-level guidance, drop-in comparison criteria, and practical circuit considerations into one engineering reference. It also identifies where a new design should remain with the MC3403 family and where a lower-voltage or differently characterized amplifier offers a better fit.

RFQ Contact
MC3403N - Quad 30V 1MHz Op Amp | Texas Instruments
MC3403N

MC3403N - Quad 30V 1MHz Op Amp | Texas Instruments

The Texas Instruments MC3403N is a quad general-purpose operational amplifier built for single- and dual-supply systems, with four amplifiers, a 30 V maximum supply rating, 1 MHz typical gain-bandwidth product, and operation from -25°C to 85°C. It is supplied in a 14-pin PDIP package. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The MC3403 belongs to the broader amplifier hierarchy: operational amplifier, analog IC, semiconductor, and general-purpose signal-conditioning component. Its quad construction reduces package count when a design needs several independent gain stages, buffers, or comparators. The verified product information identifies wide supply-voltage support, a true differential input stage, internal frequency compensation, low input bias current, a Class AB output stage, and short-circuit protection. The 1 MHz gain-bandwidth product is suitable for general-purpose audio, control, and instrumentation circuits rather than precision or high-speed applications. Because all four amplifiers share one package, supply pins and exposed signal pins must be routed carefully on mixed analog and digital boards. The 30 V supply capability permits operation from conventional single supplies or split dual supplies, making the device useful in legacy industrial, audio, and control designs. However, exact input common-mode limits, output swing, input offset voltage, supply-current, noise, and slew-rate values are not stated in the supplied verified excerpts; those parameters require confirmation in the manufacturer datasheet before final circuit sign-off. Typical applications include four-channel audio preamplification, low-frequency active filtering, sensor-signal conditioning, industrial control loops, and general buffer or gain stages. In each case, the 1 MHz bandwidth should be compared with the closed-loop gain and required settling behavior. A four-amplifier package can reduce board area, but it does not eliminate the need to check common-mode range, output swing, stability, and supply-decoupling requirements at every amplifier section. Design with a local bypass capacitor near the supply pins, maintain the required input common-mode range, and verify output-voltage headroom under the intended load. Do not infer precision performance from the word general-purpose. This product page consolidates the verified manufacturer identity, distributor listing, package, temperature range, supply rating, and replacement research while explicitly marking unavailable detailed electrical parameters. The alternatives listed here are limited to candidates supported by the supplied cross-reference data and are presented as package-compatible engineering options; final qualification should confirm pinout, supply limits, input/output ranges, offset, bandwidth, slew rate, and lifecycle status against the selected manufacturer datasheet.

RFQ Contact
MC3403NG4 - 30V 1MHz Quad Op Amp | Texas Instruments
MC3403NG4

MC3403NG4 - 30V 1MHz Quad Op Amp | Texas Instruments

The Texas Instruments MC3403NG4 is a quad, general-purpose operational amplifier with four amplifiers in a 14-pin plastic dual-inline package. It supports supply voltages up to 30 V, operates over a -25°C to 85°C temperature range, and provides a gain-bandwidth product of 1 MHz. The MC3403NG4 is therefore suitable for instrumentation, control, data acquisition, and audio-signal conditioning applications that require multiple amplifiers on one board. An operational amplifier is an active semiconductor device that uses high-gain differential amplification with negative feedback. Within the broader semiconductor hierarchy, an operational amplifier belongs to the analog amplifier and signal-conditioning category. Its inverting and non-inverting inputs determine how an external feedback network sets the closed-loop gain, while output-current capability and slew rate determine how quickly the amplifier can charge or discharge the load connected at the output. The MC3403 provides four amplifier sections, reducing the package count and board area required for multi-channel analog systems. Its 30 V maximum supply rating provides useful headroom for industrial control equipment, while the 1 MHz gain-bandwidth product supports moderate-frequency feedback networks. The specified -25°C to 85°C operating range covers many commercial and industrial environments where a wider-temperature grade is not required. Each amplifier section provides differential inputs and an output, allowing the device to implement inverting, non-inverting, summing, differential, and feedback-control circuits. Because all four sections share one package, the power rails and bypass network also serve the complete device. PCB designers should preserve symmetry between paired input and feedback components and route sensitive input traces away from output and supply-current paths to reduce parasitic pickup. Typical uses include industrial process-control loops, multichannel sensor amplification, low-frequency audio preamplification, instrumentation signal conditioning, and active filtering. The quad organization is particularly useful when four related channels must operate under a common supply. For applications requiring higher precision, lower offset, faster settling, lower noise, or rail-to-rail output operation, a newer precision amplifier family should be evaluated before committing the MC3403NG4 to the design. The most important design tradeoff is generality versus precision. The MC3403NG4 provides four inexpensive, widely applicable amplifier sections, but its 1 MHz bandwidth and legacy general-purpose architecture are not ideal for demanding sensor-front-end accuracy or high-speed signal chains. Verify input common-mode range, output swing, output-current capability, offset voltage, noise, slew rate, and stability requirements against the manufacturer datasheet for the operating conditions. This product record combines the manufacturer’s device description with application-oriented guidance for package layout, bypassing, input routing, selection tradeoffs, and drop-in evaluation. It is structured to help engineers confirm whether a legacy quad amplifier still satisfies the electrical and environmental requirements of a new instrumentation, industrial-control, audio, or data-acquisition design.

RFQ Contact
MC3403NS - Quad 30V 1MHz Op Amp | Texas Instruments
MC3403NS

MC3403NS - Quad 30V 1MHz Op Amp | Texas Instruments

Texas Instruments MC3403NS is a quad general-purpose operational amplifier rated for 30 V supply operation, 1 MHz gain-bandwidth product, and operation from -25°C to 85°C. The device is offered in a 14-pin SOIC package and contains four amplifiers, each with a Class AB output stage, true differential inputs, and internal frequency compensation. It supports single-supply operation from 3 V to 36 V or dual-supply operation, making it suitable for industrial control, instrumentation, audio, and signal-conditioning systems. An operational amplifier is an analog signal-processing IC that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. Operational amplifiers belong to the amplifier IC hierarchy, combining high open-loop gain, negative feedback, signal amplification, filtering, buffering, and active transducer conditioning. Their internal frequency compensation removes the need for an external dominant-pole capacitor in ordinary closed-loop applications. The MC3403NS provides four low-power amplifiers in one package, reducing board area compared with discrete single or dual amplifier implementations. Its low input bias current is useful when the source impedance is relatively high, while short-circuit protection improves robustness in feedback-controlled circuits. The 30 V rating and wide supply range support legacy industrial systems operating from higher-voltage rails than typical modern 3.3 V or 5 V analog circuits. Technically, each channel uses a true differential input stage and a Class AB output stage. Internal frequency compensation supports stable operation in standard closed-loop configurations, including inverting and non-inverting amplifiers. The 1 MHz gain-bandwidth product limits closed-loop bandwidth according to the selected noise gain, so higher gain reduces usable bandwidth. The wide common supply range also allows ±15 V dual-supply operation in legacy analog systems. Typical uses include four-channel sensor conditioning, general-purpose voltage amplification, audio preamplification, active filtering, data acquisition front ends, and industrial control interfaces. Multiple independent channels can process several low-frequency signals while sharing one supply and package. Where source impedance is high, input bias current and offset characteristics should be checked before selecting the amplifier. A primary design consideration is rail headroom. The output cannot swing fully to either supply rail, and single-supply designs must include sufficient voltage at the output for the downstream load. Place bypass capacitors close to the supply pins, keep feedback loops compact, and verify stability, output swing, and input common-mode range across temperature. This page combines the manufacturer specifications with package guidance, practical circuit considerations, comparison criteria, and sourcing information for engineers evaluating the MC3403NS. The technical guidance emphasizes how its 30 V supply capability, 1 MHz bandwidth, four-channel integration, and 14-pin SOIC footprint affect replacement and design decisions.

RFQ Contact
MC3403P - Quad 36V 1MHz Operational Amplifier | onsemi
MC3403P

MC3403P - Quad 36V 1MHz Operational Amplifier | onsemi

The onsemi MC3403P is a low-cost quad operational amplifier with true differential inputs, internally compensated operation, and a 14-pin plastic DIP package. It contains four amplifiers in one package and operates from a single supply or from split dual supplies, with a maximum single-supply rating of 36 V corresponding to dual operation up to ±18 V. Its 1 MHz gain-bandwidth product supports general-purpose signal conditioning at frequencies up to 1 MHz. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MC3403 belongs to the general-purpose bipolar operational-amplifier family within the broader amplifier IC and semiconductor hierarchy. Unlike circuits built around the classic UA741, the MC3403 was designed with practical single-supply operation in mind. True differential inputs also allow the amplifier to reject common-mode signals when suitable feedback networks and operating conditions are used. The MC3403P provides internally compensated amplifiers, short-circuit-protected outputs, and a Class AB output stage designed for minimal crossover distortion. Maximum input bias current is specified at 500 nA, making the device practical for higher-impedance sensing paths when leakage and bias-current errors are controlled. Its internally compensated architecture removes the need for an external compensation capacitor in the standard closed-loop configurations shown in typical applications. Each of the four amplifier sections supports common inverting, non-inverting, summing, and difference-amplifier arrangements. The 1 MHz gain-bandwidth product means bandwidth decreases as closed-loop gain increases; designers should therefore account for gain-bandwidth behavior when targeting precision, pulse, or audio-frequency signals. The 36 V maximum supply also provides ample headroom for industrial and educational circuits, although the actual common-mode and output-swing limits must be observed at lower supply voltages. Typical uses include low-frequency audio amplification, active filtering, sensor signal conditioning, waveform generation, and general instrumentation. The four independent amplifiers can implement a complete signal chain in one package, reducing board space compared with four separate single or dual amplifier ICs. In AC-coupled audio and instrumentation circuits, input and feedback components can be selected around the required gain and bandwidth rather than relying on a fixed internal compensation network. Designers should verify the MC3403P pinout before PCB assembly and observe the datasheet limits for input voltage, common-mode range, output swing, supply current, and temperature. A stable bypass capacitor near the supply pins is advisable, and the unused amplifier sections should be configured according to the manufacturer’s recommended practice rather than left floating. Because this is a through-hole DIP device, insertion and soldering require adequate clearance around the package and between adjacent board components. This product record combines verified manufacturer and distributor information, same-footprint alternatives, package and pinout details, and practical selection guidance. It is intended to help engineers identify the MC3403P quickly for legacy industrial, audio, education, and prototype designs while making package constraints and replacement limits explicit.

RFQ Contact
MC3403PG - Quad 1 MHz Operational Amplifier | onsemi
MC3403PG

MC3403PG - Quad 1 MHz Operational Amplifier | onsemi

The onsemi MC3403PG is a general-purpose quad operational amplifier with true differential inputs, a 1 MHz gain-bandwidth product, and a 0.6 V/us slew rate. The device operates from a single supply over a 3 V to 36 V range and is packaged in a 14-pin dual inline package for through-hole assembly. An operational amplifier is an analog signal-conditioning IC used to amplify voltage differences, buffer sensor outputs, and support feedback-control networks. The MC3403 belongs to the operational-amplifier hierarchy, which includes differential-input amplifiers, analog amplifiers, and integrated analog ICs. Its four amplifiers can perform independent signal-conditioning functions while sharing one package and supply connection. The principal features of the MC3403PG include four internally compensated operational-amplifier circuits, true differential inputs, a 1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a single supply as low as 3 V or as high as 36 V. The electrical characteristics are similar to the popular MC1741C, but the MC3403 adds the advantages required in modern single-supply circuitry. Split-supply operation is also possible when the total voltage between the supply terminals remains within the device's operating range. Because this is a general-purpose amplifier rather than a precision or rail-to-rail part, the input common-mode range, output swing, offset voltage, and stability behavior should be checked against the actual signal and load before final circuit approval. Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplification, transducer interfaces, general feedback-control loops, and instrumentation. The 14-DIP format is particularly suitable for through-hole prototypes, educational equipment, legacy control boards, and industrial assemblies where a through-hole quad amplifier simplifies socketed construction and servicing. When laying out a MC3403PG circuit, connect each amplifier's supply pins to the same supply network and place suitable bypassing capacitance close to those pins. Keep sensitive input routing away from high-current switching nodes, and verify that the selected feedback network remains stable with the actual source impedance and load capacitance. This product record combines the MC3403PG specifications, package information, sourcing guidance, candidate replacements, and application-oriented design notes in one place. The comparison tables and selection guidance help engineers distinguish true same-package alternatives from devices that would require board or signal-chain changes.

RFQ Contact
MC3403PT - Quad Low-Power Op Amp | STMicroelectronics
MC3403PT

MC3403PT - Quad Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC3403PT is a four-circuit, low-power bipolar operational amplifier packaged in a 14-pin TSSOP. Each amplifier supports single-supply operation to +36 V and dual-supply operation to ±18 V, providing broad flexibility for industrial, analog-control, instrumentation, and signal-conditioning designs. The device offers a 1 MHz gain-bandwidth product, internally compensated operation, short-circuit-protected outputs, and a Class AB output stage. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. Within the broader semiconductor hierarchy, the MC3403PT belongs to the operational-amplifier family, which falls under analog amplifier ICs and signal-processing semiconductors. The quad configuration places four independent amplifiers in one package, reducing board area in designs requiring multiple buffered or gain-stage channels. The principal features of the MC3403PT include a maximum input bias current of 500 nA, internal compensation, short-circuit-protected outputs, and a minimum Class AB output stage for reduced crossover distortion. Its 1 MHz gain-bandwidth product supports general-purpose amplification at low and moderate frequencies. Single-supply operation up to +36 V is especially useful when the signal source and load share a positive reference without a negative rail. The bipolar input stage supports operation from dual supplies of ±18 V or a single supply up to +36 V. Internal compensation simplifies circuit construction because separate external compensation components are not required for ordinary closed-loop amplifier use. Four independent channels can also be configured as voltage followers, non-inverting or inverting amplifiers, differential stages, comparators in suitable circuits, or general analog signal-conditioning elements. Typical uses include low-frequency sensor amplification, industrial control loops, audio preamplification, active filtering, transducers, sample-and-hold stages, and general-purpose analog boards. The quad package is particularly useful when a design needs several channels with the same supply architecture. Engineers should also evaluate output swing, slew rate, input common-mode range, and load capability against their particular signal chain. For layout, place input and output paths away from high-current switching nodes and connect the supply pins to a low-impedance bypass network. Stable feedback networks and properly grounded unused channels help prevent oscillation or unintended signal coupling. Use the manufacturer pin table and electrical-characteristics curves to verify the final operating points. This product page combines manufacturer and distributor technical information, package and pin details, lifecycle-oriented sourcing guidance, application analysis, and validated drop-in alternatives. It also highlights the differences engineers should evaluate before replacing the MC3403PT on an existing 14-pin TSSOP layout.

RFQ Contact