Products (20,000+)

MB96F315RSBPMC-GSE2 - 16-Bit 56MHz 160KB Flash MCU
MB96F315RSBPMC-GSE2

MB96F315RSBPMC-GSE2 - 16-Bit 56MHz 160KB Flash MCU

The Infineon Technologies MB96F315RSBPMC-GSE2 is a 16-bit F²MC-16FX microcontroller operating up to 56 MHz, with 160 KB of embedded Flash memory in a 48-LQFP 7 x 7 mm package. It is based on the Fujitsu 16FX architecture and is designed for embedded control applications requiring CAN/LIN networking, timer and PWM control, and DMA-assisted data movement. The device uses 0.18 µm CMOS technology and is identified with the MB96310 series designation. A microcontroller is a programmable system-on-chip that integrates a CPU core, memory, timers, communication peripherals, and I/O into one component. This device belongs to the 16-bit embedded MCU category rather than an 8-bit or high-end application processor category. Its RISC-like instruction pipeline and controller-oriented instruction set support efficient real-time control while handling multiple peripheral functions. Key verified features include a maximum internal clock frequency of 56 MHz, 160 KB Flash memory, a 48-LQFP package, and operation from 3.0 V to 5.5 V. The MB96F315 family provides CAN and LIN networking capability, timer/PWM resources, and DMA support. The supplied search data identifies 14 PWM channels, 3 timers, 36 I/O ports, and an operating temperature range from -40 °C to +125 °C. The F²MC-16FX core uses a 17.8 ns instruction cycle time according to the manufacturer data excerpt. Its instruction set covers bit, byte, word, and long-word data types, 23 addressing modes, and barrel-shift operations. These characteristics make it suitable for motor control, industrial interfaces, automotive networking, and other embedded systems where deterministic peripheral handling matters. Typical applications include CAN or LIN network nodes, motor and actuator controllers, timer-based control systems, DMA-assisted data acquisition, and general industrial embedded control. The 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V system designs, subject to the complete datasheet requirements. Designers should verify the exact peripheral configuration, pin multiplexing, clock requirements, programming method, and electrical limits in the MB96310-series datasheet before layout or firmware development. The LQFP package also requires attention to thermal performance and exposed-pad or thermal-relief practices where applicable. This page consolidates verified distributor and manufacturer-search data with practical selection context, helping engineers identify whether the MB96F315RSBPMC-GSE2 fits the required 16-bit control, networking, memory, package, and supply-voltage constraints.

RFQ Contact
MB9BF416NPMC-G-JNE2 - 144MHz Cortex-M3 MCU 512KB Flash | Infineon
MB9BF416NPMC-G-JNE2

MB9BF416NPMC-G-JNE2 - 144MHz Cortex-M3 MCU 512KB Flash | Infineon

The Infineon MB9BF416NPMC-G-JNE2 is an ARM Cortex-M3 32-bit microcontroller from the FM3 MB9B410R high-performance series, integrating 512 KB of flash memory and 64 KB of SRAM in a 100-pin LQFP (14x14 mm) package. It operates at a maximum clock frequency of 144 MHz, supports 3.3 V / 5 V supply, and provides a rich set of on-chip peripherals including CAN and LIN interfaces for automotive and industrial networking. What is an FM3 microcontroller? The FM3 family is Infineon's (originally Cypress's) line of 32-bit ARM Cortex-M3 microcontrollers positioned between low-end Cortex-M0/M0+ parts and high-performance Cortex-M4 devices. FM3 MCUs target cost-sensitive real-time applications with deterministic interrupt response, scalable Flash/RAM configurations, and integrated analog (ADC, DAC) and connectivity (CAN, LIN, USB, Ethernet) peripherals. The MB9BF416N sits in the MB9B410R sub-series which adds high-speed motor-control timers, complementary PWM outputs, and quadrature encoder interfaces for industrial drives. Key differentiating features include 144 MHz Cortex-M3 core, 512 KB flash, 64 KB SRAM, integrated CAN 2.0B and LIN 2.x controllers, 16-channel ADC, motor-control timer/PWM block, 100-pin LQFP with on-chip trace support, and wide 2.7 V to 5.5 V operating voltage range. The 100-pin LQFP footprint provides ample GPIO for multi-axis motor control and industrial sensor interfacing. The MB9BF416N uses the Cortex-M3 Harvard architecture with single-cycle multiply and hardware divide, enabling deterministic control-loop execution under 1 microsecond at 144 MHz. Its dual-bank flash supports in-field firmware updates via the bootloader, while the embedded CAN/LIN MACs allow protocol handling without CPU intervention. The high-resolution motor-control timer block generates complementary 3-phase PWM with programmable dead-time insertion for variable-frequency drives. Typical applications include BLDC/PMSM motor drives, industrial servo controllers, HVAC fan and pump controllers, automotive body electronics via CAN/LIN, factory automation PLCs, and home-appliance control boards. The combination of CAN/LIN and motor-control peripherals makes it particularly well-suited for mechatronic systems where networking and motion control co-exist. When designing with this device, pay attention to the external crystal selection and PLL configuration to achieve the full 144 MHz operation, and ensure proper decoupling on the analog supply pins to minimize ADC noise coupling into motor-current feedback paths. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes for the MB9BF416NPMC-G-JNE2 not found in the manufacturer datasheet alone.

RFQ Contact
MB9BF416RPMC-G-JNE2 - 512KB Flash Cortex-M3 MCU, 120-LQFP | Infineon
MB9BF416RPMC-G-JNE2

MB9BF416RPMC-G-JNE2 - 512KB Flash Cortex-M3 MCU, 120-LQFP | Infineon

The Infineon MB9BF416RPMC-G-JNE2 is a 32-bit ARM Cortex-M3 microcontroller in the FM3 MB9B410R family, delivering 144 MHz maximum CPU clock with 512 kByte on-chip Flash and 64 kByte SRAM. It is housed in a 120-pin LQFP (16x16 mm) package and supports a 2.7 V to 5.5 V operating voltage range, suiting both 3.3 V and 5 V system designs. According to the Cypress/Infineon datasheet (Document Number 002-05615 Rev. *D), this device also integrates CAN and LIN networking peripherals, multi-function timer/PWM blocks, and a 12-bit A/D converter. What is an FM3 microcontroller? FM3 is the original Cypress (now Infineon) FM3 family of 32-bit ARM Cortex-M3 microcontrollers, designed as a high-performance upgrade path from 8/16-bit MCUs. FM3 sits within the broader hierarchy: microcontroller -> embedded MCU -> 32-bit ARM Cortex-M MCU -> FM3 family -> peripheral-rich industrial-grade MCU. The FM3 family targets industrial motor control, factory automation, and consumer appliance designs where deterministic real-time performance and rich analog integration matter more than ultra-low-power wireless features. Key differentiating features include the 144 MHz Cortex-M3 core (with MPU), 512 kByte Flash / 64 kByte SRAM memory complement, dual CAN + LIN bus interfaces for in-vehicle networking, up to 16 channels of 12-bit ADC with up to 1 µs conversion, and multi-function timers supporting complementary PWM outputs for 3-phase motor control. The part operates from -40 °C to +105 °C, making it suitable for industrial and automotive-grade thermal environments. The MB9BF416RPMC-G-JNE2 uses a Harvard-bus architecture with tightly-coupled SRAM and Flash accelerators. The 144 MHz Cortex-M3 delivers 1.25 DMIPS/MHz, providing ~180 DMIPS peak. The peripheral DMA, interrupt controller (NVIC), and 12-bit ADC with scan-mode support enable deterministic motor-control loops at sub-microsecond latency. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), factory automation controllers (PLC, sensor hubs), automotive body ECUs with CAN/LIN networking, HVAC control boards, and home-appliance main boards. The integrated CAN/LIN and rich PWM make it a strong fit for cost-sensitive industrial-control and automotive-body platforms. When designing with this device, ensure the 120-LQFP land pattern and 4-layer PCB stack-up provide adequate copper area for thermal dissipation in high-CPU-activity workloads. Use the Infineon/Keil/IAR toolchain plus the dedicated MB9B410R peripheral library to enable rapid firmware bring-up. This page synthesizes distributor pricing, same-package drop-in alternatives (e.g., CY9BF416RPMC-G-JNE2, MB9BF416NPMC-G-JNE2), and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MB9EF226 - 32-bit ARM Cortex-R4 MCU, 128MHz, 2MB Flash | Infineon
MB9EF226

MB9EF226 - 32-bit ARM Cortex-R4 MCU, 128MHz, 2MB Flash | Infineon

The Infineon MB9EF226 is a 32-bit ARM Cortex-R4 microcontroller from the Titan family, operating at up to 128 MHz with 2 MB of embedded Flash in a 176-pin LQFP package. The device integrates high-performance processing for real-time control applications, with the Cortex-R4 core delivering RISC-like instruction throughput and deterministic interrupt response. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and peripherals. Within the broader semiconductor taxonomy, MCUs belong to integrated circuits, then to embedded processors, then to the power management hierarchy of system-on-chip devices. The MB9EF226 sits at the high-performance end of automotive-grade Cortex-R MCUs, bridging the gap between Cortex-M microcontrollers (used for general embedded control) and Cortex-A application processors (used for OS-heavy workloads). Key features include 128 MHz Cortex-R4 core with FPU support, 2 MB Flash and substantial SRAM, automotive-grade qualification under AEC-Q100, and a rich peripheral set including multiple CAN-FD interfaces, Ethernet, USB, and FlexRay. The wide operating voltage range and extended temperature capability make the device suitable for chassis and powertrain ECUs. Architecturally, the MB9EF226 uses the Titan platform with tightly coupled memory for deterministic latency. The Cortex-R4 core implements branch prediction and dual-issue capability for sustained high code density at clock speed. Hardware floating-point support accelerates sensor fusion and motor-control vector math. Typical applications include automotive body controllers, electric vehicle battery management systems (BMS), industrial motor drives, and safety-critical PLCs. The MB9EF226 is also commonly deployed in HVAC control modules where deterministic CAN-FD communication is required. When designing with this part, ensure your firmware toolchain supports Cortex-R4 (such as ARM DS-5 or IAR EWARM for Cortex-R). Decoupling capacitor placement around the 176-LQFP power pins is critical - use at least four 100 nF ceramics distributed across the package perimeter. This page consolidates distributor pricing, verified alternatives from the same Titan family, and practical PCB-layout guidance not found in the standalone manufacturer datasheet, giving engineers a faster path from selection to prototype.

RFQ Contact
MB9EF226PMC-GSE2 - 128MHz ARM Cortex-R4 MCU 2MB Flash | Infineon
MB9EF226PMC-GSE2

MB9EF226PMC-GSE2 - 128MHz ARM Cortex-R4 MCU 2MB Flash | Infineon

The Infineon MB9EF226PMC-GSE2 is an ARM Cortex-R4 32-bit microcontroller from the FCR4 MB9EF226 family, operating at 128 MHz and integrating 2 MB of flash memory in a 176-pin LQFP (24x24 mm) package. According to the manufacturer datasheet, this MCU targets real-time control and chassis/safety automotive applications, with industrial-grade temperature support. The part carries an Automotive MCU designation per the Mouser catalog entry and is supplied on tape-and-reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. The MB9EF226PMC-GSE2 belongs to the Cortex-R4 family, which is optimized for deterministic real-time response rather than the application-processing focus of Cortex-A cores. Within the broader taxonomy, this device sits under MCU -> microcontroller -> embedded processor -> semiconductor IC, and within Infineon's automotive-safety portfolio it occupies the chassis/safety MCU segment. Key features include a 32-bit ARM Cortex-R4 core running up to 128 MHz, 2 MB of on-chip flash, industrial temperature grade, and a 176-pin LQFP package per the Partstack LFQFP/SQUARE/GULL WING terminal form. The device supports automotive real-time control use cases such as electric power steering, brake systems, and chassis domain controllers. The automotive MCU classification indicates qualification for vehicle electrical-environment conditions. The Cortex-R4 core delivers deterministic interrupt latency and tightly coupled memory, which is essential when the application must respond to a sensor input within microseconds. Combined with 2 MB of flash, the device can host a full real-time operating system plus application code without external memory expansion. The 176-pin LQFP provides abundant GPIO and peripheral pinout for motor-control PWM, CAN-FD, and analog front-end integration. Typical applications include automotive electric power steering, electronic stability control, brake-by-wire systems, chassis domain ECUs, and industrial real-time controllers that benefit from the deterministic Cortex-R4 profile. The wide pin count supports parallel sensor interfaces and multi-axis motor control. When designing with this MCU, allocate PCB thermal copper under the LQFP thermal pad and verify that the chosen debug probe (e.g. J-Link or Infineon DAP) matches the SWD/JTAG pinout. Always check the firmware version against the latest errata document before locking the design. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the standalone datasheet, providing engineers with a single decision-ready reference.

RFQ Contact
MC-10105F1-821-FNA-M1-A - TPS-1 PROFINET IO SoC 100MHz | Renesas
MC-10105F1-821-FNA-M1-A

MC-10105F1-821-FNA-M1-A - TPS-1 PROFINET IO SoC 100MHz | Renesas

The Renesas Electronics MC-10105F1-821-FNA-M1-A is a TPS-1 family application-specific microcontroller / single-chip interface solution for PROFINET IO devices, integrating an ARM core with a dual-port Ethernet switch and supporting 100 Mbps full-duplex PROFINET communication. The device is housed in a 196-pin FPBGA package measuring 15 x 15 mm with 1.0 mm pitch, and is qualified for industrial operating conditions. A PROFINET IO device chip is an application-specific integrated circuit that bundles the industrial-Ethernet protocol stack, real-time (RT/IRT) media access, and a managed dual-port switch into a single silicon die so that field devices such as remote I/O blocks, variable-frequency drives, encoders, and identification readers can be designed without an external companion controller. Within the broader embedded-system hierarchy, this part sits at the junction of an industrial microcontroller (MCU), an Ethernet MAC/PHY block, and a deterministic-protocol accelerator, allowing OEMs to certify PROFINET conformance class C without writing low-level stack code from scratch. Key differentiating features include 196-BGA integration (no companion Ethernet controller needed), compliance with PROFINET specification V2.3 for real-time and isochronous real-time (IRT) classes, a 100 MHz ARM core, and Phoenix-Contact co-development with Renesas for guaranteed protocol interoperability. The dual-port integrated switch removes the need for an external PHY/MAC pair on simple star or line topologies common in field-cabinet wiring. Architecturally, the part pairs a 32-bit ARM Cortex-M-class CPU (100 MHz) with on-chip RAM, deterministic Ethernet media-access hardware, and a PROFINET IO device firmware load supplied by Renesas. This division of labor lets the host application processor focus on device-specific I/O while the TPS-1 handles cut-through switching, RT/IRT scheduling, and PROFINET alarm generation with deterministic cycle jitter below 1 µs per the device specification. Typical applications include PROFINET-IO remote I/O blocks, frequency-inverter / variable-frequency drive fieldbus interfaces, encoder and absolute-position sensor gateways, RFID-reader PROFINET nodes, and modular I/O stations in factory automation. The 100 Mbps full-duplex bandwidth comfortably exceeds typical PROFINET RT cycle times of 1 ms. When designing in the MC-10105F1-821-FNA-M1-A, plan for a 1.0 mm pitch BGA land pattern with controlled-impedance differential pairs for the MII/RGMII Ethernet traces and a 25 MHz reference crystal. Thermal management is straightforward at industrial ambient temperatures because the part is fabricated in a low-power CMOS process optimized for fan-less DIN-rail mounting. This page synthesizes distributor pricing, protocol-compliance scope, and application notes not consolidated on the manufacturer product page, helping industrial-automation design engineers evaluate the MC-10105F1-821-FNA-M1-A for PROFINET IO device integration as of 2026-10-09.

RFQ Contact
MC11E1CPBE2 - 8-Bit ROMless 2 MHz MCU | NXP | 52-LQFP
MC11E1CPBE2

MC11E1CPBE2 - 8-Bit ROMless 2 MHz MCU | NXP | 52-LQFP

The NXP Semiconductors MC11E1CPBE2 is an 8-bit ROMless HC11 microcontroller operating at up to 2 MHz, with 512 bytes of RAM, 38 I/O pins, and a 52-LQFP package measuring 10 x 10 mm. It is designed for embedded control systems requiring a compact processor, digital I/O, and automotive-oriented industrial-temperature capability. A microcontroller is a semiconductor device that integrates a CPU core, memory, input/output ports, timers, and communication interfaces on one integrated circuit. In the broader hierarchy, this MC11E1CPBE2 is an 8-bit microcontroller, part of the HC11 family, and belongs to the embedded-microcontroller and semiconductor categories. Its ROMless architecture allows the application firmware to be supplied by external memory or a programming system, supporting applications where program-memory requirements vary or field programming is required. Verified distributor data identifies the MC11E1CPBE2 as an HC11 microcontroller with a 2 MHz speed grade, ROMless configuration, 512 x 8 RAM, 38 I/O, internal oscillator, and a 52-LQFP package. The 52-terminal gull-wing package is surface-mountable and uses a 10 x 10 mm outline. Because it is ROMless, designers must verify the external memory interface and programming architecture against the original system requirements before replacing or upgrading an existing design. Typical applications include automotive electronic control units, motor and actuator controllers, sensor interfaces, industrial automation equipment, and legacy embedded systems that depend on the M68HC11 CPU architecture. The 38-I/O count provides useful connectivity for digital sensors, switches, relays, communication transceivers, and control signals. The 2 MHz CPU speed is suitable for control-loop and supervisory tasks rather than high-bandwidth signal processing or modern high-performance applications. The primary design consideration is legacy software compatibility. Firmware timing, interrupt priorities, memory-mapped peripherals, external bus behavior, and package-level routing must be preserved during any replacement. Engineers should obtain the manufacturer datasheet and verify the exact pinout, electrical limits, oscillator connections, reset requirements, and programming procedure before committing to a new PCB design. This product data summarizes verified distributor specifications, package information, sourcing references, and design considerations. It does not invent electrical limits, memory-map details, or a cross-brand substitute when the supplied web results do not establish one.

RFQ Contact
MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP
MC56F8002VWL

MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP

The NXP MC56F8002VWL is a 16-bit Digital Signal Controller (DSC) from the MC56F800x family, built on the 56800E core architecture. It delivers 32 MHz of CPU clock speed (per DigiKey/NXP listing) and integrates 12 KB (6K x 16) of on-chip Flash program memory alongside a 28-pin SOIC package with 23 general-purpose I/O pins. The part operates from a 1.8 V to 3.6 V supply range, making it well suited to low-voltage embedded designs. A Digital Signal Controller (DSC) is a hybrid class of programmable device that combines the deterministic interrupt response and peripheral integration of a microcontroller with the Multiply-Accumulate (MAC) engine and Harvard bus structure of a Digital Signal Processor (DSP). The 56800E core executes instructions in a single cycle where possible and is positioned in the taxonomy as: DSC -> DSP/MCU hybrid -> microcontroller -> integrated circuit -> semiconductor. DSCs target real-time control loops where the math throughput of a DSP is needed but the application footprint, cost, and tool chain of an MCU are preferred. Key features of the MC56F8002VWL include the 56800E 16-bit core, 12 KB Flash program memory, 32 MHz maximum core frequency, 23 GPIO lines, and a supply range of 1.8 V to 3.6 V. The integrated peripheral set reduces external component count in motor, lighting, and power-conversion designs. According to the NXP MC56F8006/MC56F8002 reference manual, the family integrates peripherals such as timers, PWM modules, ADCs, and communication interfaces configured per the variant. Architecturally, the 56800E core uses a dual Harvard memory structure with separate program and data buses, allowing simultaneous fetches that improve sustained throughput on control algorithms. The 12 KB Flash is sufficient for closed-loop field-oriented motor control (FOC), digital lighting ballast loops, and small power-factor correction (PFC) firmware where deterministic performance is more important than raw memory size. Typical applications for the MC56F8002VWL include low-cost BLDC/PMSM motor drives, switch-mode power supplies (SMPS), digital LED lighting ballasts, appliance control boards, and small industrial control modules. The wide 1.8 V to 3.6 V supply and integrated analog peripherals make it attractive for power-conversion applications where a single IC handles both sensing and control. When designing with this part, ensure your firmware budget fits within 12 KB Flash plus available RAM, and check the variant's peripheral mix against your PWM, ADC, and communication requirements. NXP's CodeWarrior and the newer MCUXpresso DSC toolchains support this family, and engineers should plan for the variant-specific header files to avoid peripheral register mismatches. This page synthesizes distributor pricing, lifecycle signals, drop-in 56800E family alternatives, and practical design notes not found in the manufacturer datasheet alone. The NXP product page flags End-of-Life for MC56F8002VWL, so designers should review replacement and obsolescence options before committing the part to long-life programs.

RFQ Contact
MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP
MC56F8006MLC

MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP

The NXP MC56F8006MLC is a 16-bit digital signal controller (DSC) from the MC56F800x family, featuring a 56800E core operating at 64 MHz bus clock with 32 MHz core MIPS throughput, 16 KB of on-chip Flash memory, and a 32-pin LQFP package. The device integrates DSP-class signal-processing capability with microcontroller peripheral integration on a single die, targeting cost-sensitive real-time control applications. A Digital Signal Controller (DSC) is a hybrid device class that combines a microcontroller's deterministic peripheral handling with a digital signal processor's mathematical pipeline. The 56800E core belongs to the family: 56800E core -> DSC -> microcontroller -> embedded processor -> semiconductor. Compared with a traditional 8/16-bit MCU, a DSC adds hardware multiply-accumulate, single-cycle MAC, and Harvard-style bus architecture, allowing closed-loop control loops, power-conversion math, and sensor fusion to run on a single chip without an external DSP partner. The MC56F8006 sits at the entry level of NXP's DSC portfolio, designed for mathematically intensive yet price-sensitive applications. Key specifications include 16 KB Flash program memory, 1.8 V to 3.6 V single-supply operation, 23 general-purpose I/O (GPIO) pins, on-chip 12-bit ADC, PWM modules suitable for motor and power control, and serial interfaces including SCI, SPI, and I2C. The device includes an internal relaxed oscillator with PLL-based frequency multiplication to derive the 64 MHz system clock from lower-cost external references. The MC56F8006 uses a Harvard-style 56800E architecture with separate program and data buses, allowing simultaneous fetch and operand access. The integrated peripheral set includes timers, PWM, ADC, and communication blocks, eliminating external components and reducing BOM cost. Built-in boundary scan and JTAG support simplify factory test and in-field firmware updates. Typical applications include BLDC and PMSM motor control in appliance fans and pumps, digital power conversion (PFC, LLC, buck/boost), LED lighting ballasts with analog dimming, and low-end industrial sensor conditioning. The wide 1.8 V to 3.6 V supply range supports both 2.5 V and 3.3 V system rails, simplifying multi-rail designs. When designing, ensure JTAG pins are accessible for factory programming and that the internal relaxed oscillator accuracy is acceptable for the target application. For motor control, leverage the integrated PWM and ADC synchronization rather than external triggering to reduce latency and BOM cost. This page synthesizes distributor pricing, NXP product-page lifecycle notes, parametric comparison with related 56F8xxx devices, and design notes covering JTAG access, oscillator selection, and motor-control timing - content not collated in the bare manufacturer datasheet.

RFQ Contact
MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP
MC56F8006VLC

MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP

The NXP MC56F8006VLC is a 16-bit digital signal controller (DSC) from the 56800E core-based 56F800x family, integrating 16KB of Flash program memory, 32MHz maximum CPU clock, and a flexible peripheral set in a 32-pin LQFP package. It combines DSP-class signal processing throughput with microcontroller peripherals, targeting mathematically intensive real-time control applications such as digital power conversion, motor control, and sensor signal conditioning. What is a Digital Signal Controller? A DSC is a hybrid device that merges the deterministic math engine of a digital signal processor with the integrated peripherals and ease-of-use of a microcontroller. Architecturally, a DSC sits above a plain MCU in the embedded hierarchy (microcontroller -> digital signal controller -> DSP) and below a stand-alone DSP, occupying a sweet spot where signal-processing throughput must coexist with PWM, ADC, timers, and GPIO. The 56800E core uses a unified data/program memory map and a modified Harvard bus, with single-cycle MAC support that is essential for power-loop and field-oriented motor-control algorithms. Key features of the MC56F8006VLC include 16KB Flash (organized as 8K x 16), 2KB RAM, an internal Phase-Locked Loop for clock multiplication, multiple 16-bit timers, a 12-bit ADC, PWM modules suited for switch-mode power supplies, and serial peripherals (SCI, SPI, I2C). The device operates from 1.8V to 3.6V, supports industrial temperature range (-40C to +105C or -40C to +125C per device marking), and provides 23 general-purpose I/O pins. The LQFP-32 footprint offers 0.8mm pitch and an exposed-pad option on the family for improved thermal dissipation. Typical applications include digital DC/DC and AC/DC power converters, small BLDC and PMSM motor drives (fans, pumps, appliances), uninterruptible power supplies, induction cooking, smart sensors, and LED drivers with closed-loop current regulation. The combination of DSP math throughput, low BOM cost, and a familiar MCU development flow makes it a strong choice for cost-sensitive embedded control where 8-bit MCUs run out of headroom. When designing with this part, ensure the JTAG/OnCE debug interface is accessible on the board, allocate proper decoupling on AVDD/DVDD pins, and follow NXP's PCB layout guidance for the analog sections to keep ADC performance within spec. Note that NXP has issued End-of-Life notices for several 56F800x variants; engineers should verify lifecycle status before committing to new designs.

RFQ Contact
MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP
MC56F8006VLF

MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP

NXP Semiconductors MC56F8006VLF is a 16-bit digital signal controller with a 32 MHz 56800E core, 16 KB of flash memory, and a 48-LQFP 7 x 7 mm package. It combines digital signal processing with microcontroller peripherals for mathematically intensive, power-sensitive, real-time control applications. A digital signal controller, or DSC, is a processor category positioned between a conventional microcontroller and a digital signal processor. MC56F8006VLF executes real-time control algorithms while providing general-purpose peripherals and embedded flash in one integrated device. Its 56800E architecture is intended for motor-control, power-conversion, and industrial automation functions where deterministic control and compact embedded integration matter. The verified manufacturer material identifies a 16-bit processing core, 32 MHz operating frequency, and 16 KB flash memory. NXP describes the entry-level MC56F8006 and MCF56F8002 devices as cost-effective solutions for power-sensitive, real-time control applications. The family integrates peripherals to reduce external component count while preserving the responsiveness required by feedback-control systems. MC56F8006VLF is supplied in a 48-LQFP package, making it suitable for conventional surface-mount PCB assembly. Its 16 KB flash capacity is sufficient for compact control firmware, configuration data, and application-specific code. The 32 MHz clock and 16-bit architecture support fast mathematical processing, while the integrated peripheral set helps simplify designs that would otherwise require separate interface and control components. Typical applications include digital motor control, power-supply regulation, industrial inverter control, signal conditioning, and embedded instrumentation. The part is particularly relevant when a system needs deterministic digital filtering or feedback calculations but does not require a high-end digital signal processor. NXP’s product family positioning emphasizes mathematically intensive, power-sensitive control rather than general-purpose processing. For a new design, verify supply voltage, peripheral assignments, timing, pin multiplexing, programming requirements, and package-level constraints against the manufacturer datasheet before committing the PCB. Because MC56F8006VLF is identified as end-of-life by the NXP product page, engineers should also confirm availability, lifecycle status, and approved sourcing options before starting a production release. This page combines verified manufacturer identity, distributor specifications, lifecycle context, package information, and practical sourcing considerations. It is intended to help engineers locate the datasheet, assess the device’s real-time control role, and determine whether a legacy design requires migration planning.

RFQ Contact
MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP
MC56F8006VWLR

MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP

The NXP MC56F8006VWLR is a 16-bit 56800E-core Digital Signal Controller (DSC) that integrates the processing power of a DSP with the peripheral integration of a microcontroller, packaged in a 28-pin wide-body SOIC (SOIC-28-300mil). Per the manufacturer datasheet, it delivers up to 32 MIPS at 32 MHz core clock, with 16 KB of program Flash (organized as 8K x 16) and operates from a 1.8 V to 3.6 V supply. A Digital Signal Controller (DSC) is a hybrid device that occupies the architectural middle ground between a pure microcontroller (MCU) and a digital signal processor (DSP). It uses a modified Harvard architecture with a deterministic interrupt model, on-chip memory, and DSP-class multiply-accumulate instructions that allow closed-loop control loops to execute in a single instruction cycle. DSCs are widely used in digitally controlled switching power supplies, motor drives, sensor signal conditioning, and LED lighting where tight math latency matters more than raw GHz throughput. Key features of the MC56F8006 include 16 KB Flash / 2 KB RAM, a 6-channel PWM module suitable for three-phase or multi-channel DC/DC control, a 12-bit ADC, 23 GPIO lines, and on-chip relaxation oscillator. Integrated peripherals such as the programmable interval timer, queued serial peripheral interface (QSPI), and inter-integrated circuit (I2C) interface reduce external component count, lowering both BOM cost and PCB area. The device is qualified to -40 °C to +105 °C industrial temperature range. Architecturally, the 56800E core couples a unified data/program address space with dual operand fetches per cycle, enabling one-cycle MAC instructions that close PI or state-observer loops in motor-control firmware well within 32 MHz. The on-chip voltage regulator generates logic-level rails from the 1.8 V to 3.6 V external supply, simplifying analog/digital supply partitioning. Typical applications include switched-mode power supplies (SMPS), digital motor control (BLDC, PMSM, and stepper), solar micro-inverters, smart LED drivers, and industrial sensor conditioning. The wide operating voltage and industrial temperature grade also suit 12 V/24 V automotive-body and appliance platforms. A key design consideration is Flash endurance: typical 10,000 write/erase cycles per sector constrain in-application firmware updates. Designers should reserve a bootloader sector and follow NXP's recommended erase-modify-write sequence. This page synthesizes distributor pricing, parametric comparison against drop-in alternatives, and practical design guidance not typically consolidated on a single manufacturer datasheet.

RFQ Contact
MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP
MC56F8013VFAE

MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP

The NXP MC56F8013VFAE is a 16-bit digital signal controller (DSC) in the 56800E 56F8xxx family, delivering 32 MHz core performance with 16 KB (8K x 16) of on-chip Flash and a 32-pin LQFP (7x7 mm) package. It integrates the computational power of a DSP with the peripheral set of a microcontroller on a single die, targeting cost-sensitive embedded control applications. The device operates from a 3.3 V supply and is qualified to AEC-Q100 for automotive deployments. What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid class of embedded processor that combines microcontroller (MCU) peripherals and interrupt-driven control with the deterministic numeric throughput of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU (e.g., ARM Cortex-M0) and a standalone DSP (e.g., TI C6000). DSCs are widely used in motor control, power conversion, and sensor-fusion applications where both deterministic control loops and arithmetic DSP kernels are required on one chip. The 56800E core used in the 56F8013 family adds a Harvard-style memory architecture and single-cycle MAC operations typical of DSP cores. Key features of the MC56F8013 include 16 KB Flash, 4 KB RAM, a 32 MHz 56800E core with single-cycle 16-bit multiply-accumulate, dual 6-channel PWM modules for motor drive, two 12-bit ADCs with up to 8 channels, and communication peripherals including SCI, SPI, and I2C. The 56F8013 derivative adds a CAN 2.0 A/B module versus the lower-feature 56F8011 sibling. On-chip regulators and a low-power Stop mode reduce quiescent draw for battery-connected systems. Typical applications span BLDC/PMSM motor drives (drones, e-bikes, appliances), digital switched-mode power supplies (PFC + LLC), automotive sensor interfaces, and industrial servo loops. The 56800E instruction set is C-friendly and supported by NXP's CodeWarrior and the newer MCUXpresso toolchain plus Processor Expert graphical configuration. Design considerations: maintain a clean analog ground island for ADC accuracy, place the 3.3 V decoupling network within 5 mm of the supply pins, and verify PWM timing closure against the application's control-loop rate. The LQFP-32 footprint allows hand-soldering and rework on prototype boards.

RFQ Contact
MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP
MC56F8014VFAE

MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8014VFAE is a 16-bit digital signal controller microcontroller operating at up to 32 MHz, with 32 KB of flash memory, 8 KB RAM, PWM outputs, and COP/LVD support in a 32-LQFP (7x7 mm) package. It combines DSP and MCU functionality in the 56800E architecture, making it suitable for real-time motor-control and embedded signal-processing systems. A digital signal controller is a microcontroller architecture optimized for deterministic control loops and computationally intensive signal processing. The MC56F8014 combines a 16-bit core, programmable peripherals, ADC channels, PWM, and watchdog-related supervisory functions within one integrated device. Its dual Harvard-style architecture uses multiple execution units to support parallel instruction operations and efficient C-based control code. The verified device information identifies a maximum core frequency of 32 MHz, 32 KB program flash, and 8 KB RAM. The controller also includes one 5-channel PWM module and two 4-channel 12-bit ADC modules according to the supplied technical description. These resources support motor-control loops, digital power conversion, measurement systems, and embedded automation products. COP and low-voltage detection functions help supervise system operation and supply conditions. The MC56F8014VFAE is packaged in a 32-LQFP, 7x7 mm surface-mount package. The 32 MHz operating point provides a balance between control-loop responsiveness and embedded resource consumption, while the unified DSP/MCU architecture can reduce the need for separate general-purpose logic and signal-processing components. Exact pin functions, electrical limits, memory organization, timing, and peripheral behavior should be confirmed in the NXP 56F8014 technical data sheet. Typical applications include brushless DC motor control, digital motor controllers, power-conversion control, industrial automation, and embedded control systems with analog feedback. The 12-bit ADC resources suit sensor and current-voltage feedback, while PWM outputs support actuator and power-stage timing. CodeWarrior-oriented development and the MCU-style programming model support embedded firmware integration. Designers should verify the complete pin multiplexing, voltage limits, clock configuration, ADC conversion timing, PWM dead-time requirements, and package-level thermal conditions against the manufacturer datasheet before layout or firmware release. This page consolidates the supplied manufacturer, distributor, and cross-reference information while clearly identifying parameters that require datasheet confirmation.

RFQ Contact
MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP
MC56F8025VLD

MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP

The NXP MC56F8025VLD is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, combining DSP performance with MCU-style peripheral integration, housed in a 44-pin LQFP (10x10 mm) package. It delivers up to 32 MIPS at 32 MHz, integrates 32 KB of program Flash and 8 KB of unified RAM, and targets cost-sensitive digital motor control and power conversion designs. The 56800E dual Harvard architecture features three parallel execution units capable of up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid device that fuses a microcontroller's deterministic peripheral set with a digital signal processor's MAC engine and single-cycle arithmetic units. In the system hierarchy it sits between microcontrollers (MCUs) and full digital signal processors (DSPs), and is itself a member of the broader power management and embedded control IC family. The 56800E family includes 16-bit fixed-point MAC, hardware DO loops, and an MCU-friendly programming model that compiles cleanly from C, enabling rapid DSP code generation without manual assembly tuning. Key features include dual 12-bit successive-approximation ADCs with up to 8 input channels, two PWM modules with six complementary outputs suitable for 3-phase motor drive, one quad-timer, two SCI (UART) ports, one SPI port, one I2C port, and an on-chip relaxation oscillator. The device operates from a 3.0 V to 3.6 V supply across -40 C to +105 C, with internal 2.5 V regulator-derived logic supply and brown-out reset. The 44-LQFP package provides 32 GPIO with high-current sink/source capability for direct gate-driver interface. Typical applications include low-cost BLDC and PMSM motor drives (appliance fans, pumps, small HVAC blowers), digital PFC and LLC power conversion front-ends, solar micro-inverter control loops, induction cookware quasi-resonant converters, and LED lighting ballast controllers. NXP's Processor Expert and FreeMASTER tooling provides auto-generated peripheral drivers and a real-time variable watch for in-circuit tuning, dramatically shortening the firmware design cycle. A practical design consideration: route the analog ADC reference (VREF) and analog supply (VDDA) separately from the noisy digital supply (VDD), and place the 1 uF and 0.1 uF decoupling pair within 3 mm of each supply pin. Avoid running PWM switching traces under the analog ADC input traces to minimize coupled noise.

RFQ Contact
MC56F8027MLH - 16-Bit Automotive Digital Signal Controller
MC56F8027MLH

MC56F8027MLH - 16-Bit Automotive Digital Signal Controller

The NXP Semiconductors MC56F8027MLH is a 16-bit digital signal controller combining an MCU-style programming model with dedicated DSP execution resources. The device is associated with the 56800E dual Harvard-style core architecture, whose three parallel execution units can perform as many as six operations per instruction cycle. MC56F8027MLH is packaged in a 64-terminal square gull-wing LFQFP package measuring 10 mm by 10 mm and is identified as automotive-grade in the verified distributor data. A digital signal controller is a microcontroller optimized for real-time control and signal-processing workloads. Unlike a general-purpose microcontroller, it integrates execution resources and instructions that improve throughput for operations such as filtering, control-loop calculation, waveform processing, and mixed control-plus-DSP tasks. Within the embedded-device hierarchy, the MC56F8027MLH is a microcontroller, an embedded processor, and a real-time signal-processing controller. The verified NXP datasheet identifies MC56F8027MLH as part of the 56F8000 family of 16-bit digital signal controllers. Its architecture supports parallel operation, while its MCU-oriented programming model and optimized instruction set are designed to generate efficient DSP and control code. This combination makes the controller relevant to automotive electronics, motor and motion control, industrial automation, consumer equipment, and other embedded systems that must combine deterministic control with real-time signal processing. The three execution units operate in parallel within a dual Harvard-style architecture. According to the NXP manufacturer datasheet, this arrangement allows as many as six operations per instruction cycle, while the instruction set is designed for efficient use by C compilers. This provides a clearer software and hardware rationale than treating the device only as a conventional MCU: control-loop code and arithmetic signal-processing operations can share one programmable platform. Typical application areas include motor control, power conversion, industrial automation, automotive body or accessory electronics, audio and communication signal processing, and compact embedded instruments. Suitability depends on the exact peripheral configuration, memory variant, clock requirements, voltage range, temperature grade, and package-specific pin functions listed for the ordered device. Those detailed operating limits and resources must be confirmed in the NXP datasheet before schematic or firmware commitment. When designing a board, route all 64 terminals according to the package pinout and preserve the required power, ground, clock, programming, and signal-conditioning connections. Firmware and peripheral use should follow the datasheet's startup, interrupt, timing, and low-power procedures. The combination of 16-bit digital signal control, parallel core execution, and a 64-lead automotive package makes MC56F8027MLH a specialized embedded platform rather than a general register-compatible substitute for unrelated microcontrollers. This page consolidates the verified package, architecture, lifecycle-relevant sourcing, and manufacturer-datasheet links while clearly separating unavailable specifications. Its practical value is the combination of application guidance, design cautions, and a transparent assessment of replacement availability for this specialized DSP-controller platform.

RFQ Contact
MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP
MC56F8027VLH

MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8027VLH is a 16-bit digital signal controller with a 56800E core, 32 KB flash memory, 32 MHz operating frequency, and a 64-LQFP package. It combines digital signal processing and microcontroller functions for embedded control, industrial lighting, and signal-processing systems. The device also provides 8 KB RAM, high-resolution PWM, a 12-bit ADC, and multiple serial interfaces according to the NXP product information. A digital signal controller is a microcontroller optimized for real-time signal acquisition, filtering, modulation, and control. Unlike a general-purpose microcontroller, the MC56F8027VLH integrates dedicated signal-processing peripherals with a deterministic embedded-control architecture. This makes it suitable for applications that must acquire analog signals, execute control calculations, and generate accurately timed outputs within one integrated device. The 56800E core provides 16-bit processing at up to 32 MHz, while 32 KB of flash supports firmware storage and 8 KB of RAM supports working data. The 12-bit ADC is useful for monitoring analog process variables, and the high-resolution PWM supports precision actuator, power-conversion, and lighting-control functions. Multiple serial interfaces enable connection to sensors, transceivers, memory, and industrial equipment. The 64-LQFP package provides a defined external pin arrangement and is suitable for conventional PCB assembly. Its larger lead pitch and exposed perimeter make it easier to inspect and manufacture than a fine-pitch package, although the device requires careful routing of power, ground, analog, and communication signals. The NRND lifecycle status indicates that the part should be selected carefully for new designs, while existing designs should verify availability and migration requirements before committing to production. Typical uses include industrial lighting controllers, motor and power conversion control, digital signal processing modules, instrumentation, and embedded systems requiring a combination of analog measurement and real-time computation. Firmware should account for the 12-bit ADC characteristics, PWM timing, serial peripheral configuration, and the package-specific pin multiplexing before hardware production. One key design consideration is to validate the complete signal path rather than selecting the controller only by clock rate. Analog input filtering, reference stability, PWM dead time or polarity, serial timing, and firmware interrupt latency determine system performance. Confirm the latest datasheet and NXP product-change notices before an NRND part is used in a new production program. This page consolidates verified manufacturer and distributor information, lifecycle status, package details, application guidance, and replacement analysis for engineers evaluating the MC56F8027VLH. Pricing and availability are referenced as of 2026-10-21 where distributor data provides them.

RFQ Contact
MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP
MC56F8037MLHR

MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP

The NXP MC56F8037MLHR is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, offering up to 32 MIPS performance with 32 KB of program Flash and 4 KB of unified data/Flash memory. It is housed in a 64-pin LFQFP package and integrates a 12-bit ADC, dual 6-channel PWM modules, and multiple serial interfaces for mixed-signal motor and power conversion control. A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and on-chip peripherals of a microcontroller with the high-throughput computational capability of a digital signal processor. In the broader component taxonomy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP) under the umbrella of embedded controllers. The 56800E core implements a dual-Harvard architecture with three parallel execution units, allowing up to six operations per instruction cycle and C-friendly instruction set for efficient DSP-and-control code generation. Key features include 32 KB Flash with security, 2.5 KB RAM, a 12-bit ADC with 16 input channels and 2.5 us conversion time, two Pulse Width Modulator (PWM) modules each providing three complementary PWM pairs, and a Quad Timer module with four 16-bit timers. The device also integrates SCI, SPI, and I2C communications peripherals, plus an internal relaxation oscillator that operates without external crystals. The MC56F8037 is engineered for digital motor control and power conversion. Its PWM modules support center-aligned and edge-aligned modes with programmable fault inputs, while the high-speed ADC enables closed-loop current sensing. Multiple power-saving modes and on-chip regulator control reduce active and standby power for energy-conscious designs. Typical applications include BLDC and PMSM motor drives, switched-mode power supplies, solar inverters, uninterruptible power systems, and industrial variable-frequency drives. Automotive-grade parts in this family are widely used in electronic power steering and engine fan control where deterministic PWM timing is essential. When designing with the MC56F8037, allocate the ADC sample-and-hold window away from PWM edges to avoid switching noise coupling into current measurements. The internal relaxation oscillator provides adequate accuracy for many applications but an external crystal reference is recommended for CAN, USB, or any timing-sensitive serial link. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet front page, all cross-referenced against the NXP MC56F8037 datasheet and current distributor stock data.

RFQ Contact
MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors
MC56F8037VLH

MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors

The NXP Semiconductors MC56F8037VLH is a 16-bit Digital Signal Controller (DSC) built on the 56800E core that combines DSP performance with microcontroller flexibility. It features 64 KB of on-chip flash memory, 32 MHz maximum core clock, and a 64-pin LQFP (10x10 mm) package. The 56800E core employs a dual Harvard-style architecture with three parallel execution units enabling up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid semiconductor class that integrates a microcontroller's deterministic control peripherals with a digital signal processor's mathematical throughput on a single die. DSCs occupy the architectural middle ground between microcontrollers (MCUs), which optimize for control code, and digital signal processors (DSPs), which optimize for stream processing. Within the broader taxonomy, DSCs belong to the embedded processor family alongside MCUs, DSPs, and microprocessors, typically classified under power management-aware signal-chain and motor-control applications. Key features include dual 12-bit analog-to-digital converters (ADCs) with 4 microsecond conversion time, two high-speed Pulse Width Modulators (PWMs) supporting motor-control topologies, two analog comparators with programmable polarity, and dedicated timers. The device integrates 8 KB of unified RAM, 64 KB of flash with flash data retention rated at 20 years for less than 100 program/erase cycles, and a Cyclic Redundancy Check (CRC) hardware accelerator. Communication peripherals include SPI, I2C, UART, and CAN interfaces. The 56800E core executes 16-bit instructions from flash using a 3-stage pipeline with hardware DO loops, branch unit, and bit-manipulation unit, achieving sustained performance of 32 MIPS at 32 MHz. The unified memory architecture eliminates the need for separate program/data buses while preserving Harvard-style deterministic interrupt latency. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), home appliances (washing machines, refrigerators, HVAC blowers), solar micro-inverters, and uninterruptible power supplies. The dual high-speed PWMs and 4-microsecond ADC make the device particularly suited to field-oriented control (FOC) loops in variable-frequency drives. Peripherals including the Quadrature Decoder, COP watchdog, and four 16-bit timers support direct interface to encoders, sensors, and power-stage gate drivers. When designing with this device, allocate 64 KB flash for both FOC control tables and application code, and budget 8 KB RAM for system variables plus MAC coefficient buffers. The 3.0 V to 3.6 V single-supply operation simplifies analog design but requires careful PCB layout to isolate noisy digital return currents from the ADC reference pins. Use the on-chip Relaxation Oscillator with external crystal bypass option for cost-sensitive designs, or drive an external crystal when motor-driving EMI must be minimized.

RFQ Contact
MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP
MC56F8037VLHR

MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP

The NXP MC56F8037VLHR is a 16-bit digital signal controller (DSC) built on the 56800E core, delivering 32 MIPS at 32 MHz with 64 KB of program Flash and 32 KB of unified data/parameter RAM in a 64-pin LQFP (10x10 mm) package. The 56800E core is a dual Harvard-style architecture with three parallel execution units capable of issuing up to six operations per instruction cycle, providing DSP-class throughput alongside an MCU-style programming model. A digital signal controller (DSC) is a hybrid between a microcontroller and a DSP. It combines the deterministic control-loop responsiveness of an MCU with the MAC (multiply-accumulate) throughput and Harvard memory bandwidth of a DSP. Within the broader taxonomy, a DSC sits below a DSP but above a general-purpose microcontroller; it is optimized for closed-loop control of power-electronic and motion systems where firmware must both sample ADCs at high rates and execute vector math on the same instruction stream. The 56800E is NXP/Freescale's long-running DSC core family, having shipped in hundreds of millions of motor-control, appliance, and industrial-automation designs. Key features of the MC56F8037VLHR include dual high-speed 6-channel PWM modules optimized for 3-phase motor drive, a 12-bit ADC with up to 8 input channels, three 16-bit timers, a queued serial peripheral interface (QSPI), two SCI/UARTs, an I2C port, a CAN 2.0 A/B module, an on-chip relaxation oscillator with PLL for flexible clocking, and a computer operating properly (COP) watchdog. The device operates from 3.0 V to 3.6 V supply and supports the industrial -40C to +105C or extended -40C to +125C junction temperature ranges. Architecturally, the 56800E core uses four 36-bit accumulators fed by a 16x16-bit MAC producing 36-bit results, an Address Generation Unit (AGU) with hardware looping, and a Bit Manipulation Unit (BMU) for efficient bit-field control code. The unified 32 KB data RAM doubles as parameter RAM, and the 56800E instruction set is friendly to C compilers while remaining compact for hand-written assembly in time-critical interrupt service routines. Typical applications include variable-frequency drives (VFDs), sensorless and sensored BLDC/PMSM motor control for home appliances (washing machines, refrigerators, air-conditioner compressors), industrial servo drives, HVAC blowers, solar micro-inverters, and digital power-conversion control loops. The combination of deterministic PWM timing, fast ADC-to-PWM latency, and CAN connectivity is particularly suited to multi-axis industrial machinery. Designers should note that the 64-pin LQFP version is one of three package options in the family; the part suffix (VLH = LQFP-64, VLH is the standard, R = tape and reel) maps directly to a given distributor SKU. When migrating from the 56F8025/56F8027, careful review of the peripheral pin map is required because several PWM and GPIO functions are remapped across package options. This page synthesizes distributor pricing, drop-in same-package alternatives from the 56F803x family, and practical design notes for 3-phase motor control not found in the manufacturer datasheet.

RFQ Contact
MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP
MC56F8122VFAE

MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP

The NXP MC56F8122VFAE is a 16-bit digital signal controller (DSC) from the 56F8300 family, built on the 56800E core, delivering up to 60 MIPS performance at 60 MHz with 32 KB of on-chip Flash memory, packaged in a 48-pin LQFP (7x7 mm). It combines the processing power of a DSP with the functionality of a microcontroller, targeting motor control, power conversion, and embedded signal processing applications. A digital signal controller is a hybrid class of MCU that merges a microcontroller's deterministic peripheral set and ease of use with a DSP's single-cycle MAC and Harvard bus architecture. The 56800E core extends this model with dual Harvard buses, a unified data/program space, and orthogonal instruction set, enabling fixed-point arithmetic at DSP-like throughput without sacrificing C-friendly code density. Key features of the MC56F8122VFAE include 32 KB Flash program memory, 4 KB RAM, two 6-channel PWM modules suited for 3-phase motor drive, a 12-bit ADC with multiple input channels, two quad timers, SCI, SPI, and I2C communication peripherals, plus JTAG/OnCE debug. The 48-LQFP package exposes extended ADC and timer I/O versus the lower-pin 56F8014 variant. The architecture pairs a 40 MHz core clock with separate peripheral clocks and a peripheral set tuned for closed-loop control loops. Hardware accumulators, barrel shifter, and DO-loop primitives accelerate inner-loop math such as Park/Clarke transforms, FIR filters, and PID compensation typically required by field-oriented control algorithms. Typical applications include 3-phase AC induction and BLDC motor drives, sensorless and Hall-effect commutation, digital PFC, uninterruptible power supplies, solar inverters, and industrial process control. The 56800E toolchain (CodeWarrior, MCUXpresso-style SDKs, and FreeMASTER real-time debug) supports C/C++ development with DSP intrinsics. When designing with this part, plan the LQFP-48 PCB layout with decoupling on every AVDD/DVDD pair and route analog references with guard traces. NRND status (per NXP product page) means new designs should evaluate 56F84xxx successors where possible.

RFQ Contact
MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP
MC56F8123VFBE

MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8123VFBE is a 16-bit digital signal controller with a 56800E core, 40 MHz processing speed, 32 KB of Flash program memory, and a 64-LQFP 10 x 10 mm package. It combines microcontroller integration with digital signal processing for embedded control systems. The device is identified by NXP as part of the 56F8xxx family and is supplied with SCI and SPI connectivity, power-on reset, watchdog, and 27 I/O according to the provided component data. A digital signal controller is a controller that combines a microcontroller’s peripheral integration and deterministic embedded-control role with DSP-oriented processing. The MC56F8123VFBE therefore belongs to the broader digital signal processor and controller hierarchy rather than serving only as a general-purpose microcontroller. Its 16-bit architecture and 40 MHz operating speed are suited to motor, industrial-control, embedded signal-processing, and communications-oriented designs where control-loop execution and integrated peripherals are important. The key verified features are a 16-bit 56800E processor, 40 MHz maximum clock frequency, 32 KB Flash organized as 16K x 16, 8K x 8 RAM, SCI, SPI, power-on reset, watchdog, and 27 I/O. The listed package is a 64-LQFP 10 x 10 mm surface-mount package. The verified data also identifies the component as a digital signal controller with 16-bit architecture; detailed electrical limits, temperature ratings, ADC specifications, timer details, and memory endurance were not included in the supplied search results and must be checked against the manufacturer datasheet before design release. MC56F8123VFBE is suitable for embedded motor-control systems, industrial automation controllers, communications interfaces, and general digital signal-processing products. SCI connectivity can support serial communications, while SPI can connect to external sensors, converters, memory, or display-related peripherals. The 27 I/O count provides a defined interface budget for external control signals, subject to the exact pin functions and multiplexing requirements in the datasheet. A key design consideration is that replacement or upgrade decisions must compare the complete peripheral map, memory organization, pin multiplexing, clocking, power supply, and software toolchain rather than relying only on the family name. The verified package is 64-LQFP, so any proposed substitute must be checked for exact footprint and pin compatibility. Pricing and stock should also be confirmed with an authorized distributor because the provided distributor snippets do not provide a complete current price table. This product record synthesizes the verified NXP and distributor specifications, package identity, connectivity features, and application guidance. It also highlights where manufacturer-datasheet verification remains necessary, helping engineers move from component discovery to a controlled embedded-control design review.

RFQ Contact
MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP
MC56F8145VFGE

MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP

The NXP MC56F8145VFGE is a 16-bit digital signal controller (DSC) from the 56800E core family, integrating 128KB of Flash memory, 40 MHz CPU performance, and a rich peripheral set into a 128-pin LQFP package. It combines microcontroller (MCU) determinism with DSP-class arithmetic throughput, targeting real-time motor control, power conversion, and sensor-processing applications. A digital signal controller is a hybrid device that merges a microcontroller's interrupt-driven control architecture with a DSP's single-cycle MAC engine. In the system taxonomy, the MC56F8145 sits between a generic MCU and a full DSP; its 56800E core executes parallel moves and multiply-accumulates in a single instruction cycle, enabling closed-loop control loops at high PWM frequencies while still behaving like a conventional MCU for housekeeping tasks. Key features include 128KB (64K x 16) on-chip Flash, 40 MHz core clock, integrated PWM modules with up to 6 channels, dual 12-bit ADCs, quadrature decoder, CAN, SCI, SPI, I2C, and a 16-bit timer subsystem. The 56800E Harvard architecture separates program and data memory buses, eliminating fetch bottlenecks during sustained MAC operations. The device targets motor control (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC, full-bridge), and industrial sensor interfacing. Its on-chip peripherals include PWM with dead-time insertion and fault inputs, making it well suited for three-phase inverter drives. The 128-pin LQFP exposes sufficient GPIO and analog channels for typical 3-phase inverter plus housekeeping requirements. Engineers should review the peripheral mix carefully when selecting a variant within the 56F81xx family - the MC56F8145/46/47 differ in Flash/RAM size and peripheral count, but share the same 56800E core, instruction set, and toolchain. This page synthesizes distributor pricing, drop-in 56F81xx alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
MC56F8146VFV - 16-Bit 128KB Flash 3.3V MCU | NXP
MC56F8146VFV

MC56F8146VFV - 16-Bit 128KB Flash 3.3V MCU | NXP

The NXP Semiconductors MC56F8146VFV is a 16-bit CISC microcontroller with a 40 MHz MC56F81xx processor core, 128 KB of flash memory, and a 3.3 V supply requirement, housed in a 144-pin LQFP package. It is designed for embedded control and digital signal processing systems where deterministic execution, integrated memory, and a high pin count provide useful peripheral connectivity. The verified product data identifies the device as a digital signal processor-class component with an LFQFP package and industrial temperature grade. A microcontroller is a programmable semiconductor device that combines a processor core, memory, and peripherals into one embedded-control component. The 16-bit MC56F8146VFV belongs to the microcontroller and embedded-processor hierarchy rather than a general-purpose personal computer processor. Its 128 KB flash memory provides nonvolatile program storage, while its 144-pin package exposes a broad set of I/O and control connections for external sensors, communication interfaces, actuators, and system support circuitry. The key verified attributes are the 16-bit CISC architecture, 40 MHz operating frequency, 128 KB flash memory, 3.3 V supply, and 144-pin LQFP construction. The MC56F81xx family designation and 40 MHz core make the part suitable for control loops, industrial equipment, motor-related functions, embedded signal processing, and systems requiring a relatively large package pin count. The industrial temperature classification is specifically reported by the verified distributor data. The product is commonly described as a digital signal processor because the MC56F81xx architecture combines control-oriented processing with signal-handling capabilities. Its 144-pin package is substantially larger than small 8-pin or 32-pin microcontrollers, allowing more peripheral connections and supporting systems with multiple digital I/O, communications, and control functions. The LQFP form factor also supports conventional surface-mount PCB assembly while providing generous perimeter access for routing. Designers should confirm pin functions, electrical limits, clock requirements, memory organization, and peripheral availability against the official NXP MC56F8146VFV datasheet before finalizing a PCB. Although the supplied web data confirms the package, memory, voltage, core frequency, architecture, and industrial classification, it does not provide a complete pinout, electrical maximums, peripheral inventory, or detailed timing specifications. LCSC lists a starting price of $1.0047, while other distributor pricing and availability should be checked directly before purchasing. This page combines verified source data with explicit data gaps rather than inferring unconfirmed electrical values.

RFQ Contact