Products (22,000+)

MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL16Z64VFM4

MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

NXP Semiconductors MKL16Z64VFM4 is a 32-bit ARM Cortex-M0+ Kinetis KL1 microcontroller operating up to 48 MHz, with 64 KB of programmable flash memory and USB and analog peripherals in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device targets low-power embedded systems where compact size, USB connectivity, and a general-purpose ARM microcontroller architecture are important. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one device. The Cortex-M0+ core belongs to the ARM microcontroller product hierarchy, where its compact instruction set and deterministic operation support cost-sensitive embedded control. Within NXP's product portfolio, the Kinetis KL1 family combines this efficient core with low-power design options and USB connectivity for connected peripherals, industrial controls, and compact consumer equipment. The MKL16Z64VFM4 provides 64 KB of flash, a 48 MHz maximum operating frequency, and a 32-bit architecture. Its integrated USB capability allows a design to communicate with a host without adding a separate USB interface controller. Analog peripherals support applications that must measure or control real-world signals, while the 5 mm by 5 mm HVQFN package reduces board area compared with larger leaded microcontrollers. Supported operating-voltage options listed for the device include 1.8 V, 2.5 V, and 3.3 V. The Kinetis architecture is suited to low-power embedded designs because the processor and peripherals are optimized for efficient control workloads. Flash memory retains programmed firmware when power is removed, and the Cortex-M0+ platform provides a familiar instruction set and development ecosystem. Because the MKL16Z64VFM4 has limited 64 KB flash capacity, firmware planning should account for code size, boot code, application logic, and configuration data before finalizing the product's feature set. Typical uses include USB-connected data loggers, compact industrial sensing modules, motor and valve controllers, access-control peripherals, and low-power instrumentation. A USB data logger can use the integrated interface for enumeration and data transfer, while an industrial controller can apply analog peripherals to sensor acquisition and digital outputs to actuators. The small package is especially useful when the PCB area is constrained but full-size leaded packages are undesirable. When laying out the PCB, place input, output, and decoupling capacitors close to their associated power pins, and route the exposed pad to the thermal and ground structure required by the manufacturer package drawing. Preserve USB-signal routing geometry and provide a clean, continuous ground path beneath the interface. Firmware and peripheral assignments should be checked against the manufacturer's reference manual and device configuration guidance before production. This product record combines the exact device identity, core, memory, frequency, package, connectivity, and sourcing information with same-family alternatives and practical integration guidance. It helps engineers assess whether the 32-pin Kinetis KL1 MCU matches a board footprint, power architecture, USB requirement, and embedded firmware budget before committing to a design.

RFQ Contact
MKL16Z64VFT4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP (Tape & Reel)
MKL16Z64VFT4

MKL16Z64VFT4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP (Tape & Reel)

The NXP MKL16Z64VFT4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB of SRAM, supplied in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. The Kinetis KL16 sub-family targets general-purpose low-power applications that need USB connectivity, segment-LCD support, and a richer analog peripheral set than the entry-level KL0x family, while preserving the KL0x energy-efficiency envelope. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a fixed set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M0+ core used here is the most energy-efficient member of the Cortex-M family, designed for deterministic real-time control in cost-constrained embedded products. The Kinetis family sits within NXP's broader portfolio of 32-bit microcontrollers, which in turn belongs to the larger category of microcontrollers and microprocessors (semiconductor -> IC -> MCU -> Kinetis -> KL1x). Key specifications include a 48 MHz maximum core clock, 64 KB program Flash, 8 KB SRAM, USB 2.0 full-speed device with on-chip transceiver, segment-LCD driver (up to 8x36 or 4x40 segments), 12-bit SAR ADC with up to 16 single-ended channels, low-power UART/SPI/I2C peripherals, and an operating voltage range of 1.71 V to 3.6 V. The device also integrates a low-power RTC, multiple low-power modes (VLLS0..3, LLS, VLPR, STOP), DMA, and a low-power timer for periodic wake-up. The 48-QFN exposed-pad package provides a low thermal resistance and a compact 7x7 mm footprint for space-constrained boards. Architecturally, the KL16 combines a Cortex-M0+ core, single-cycle I/O bus, and a peripheral bridge feeding independent timer, communication, and analog subsystems. The on-chip voltage regulator supports internal core supply from a single external 1.71-3.6 V rail, eliminating the need for multiple external supplies. Hardware AES is not present on this sub-family, but the segment LCD controller, USB FS device, and 12-bit ADC give it strong suitability for human-interface, metering, and consumer products. Typical applications include battery-powered sensor nodes, USB-CDC or USB-HID consumer accessories, small appliances with segment-LCD displays, electronic shelf labels, low-end smart meters, and portable medical accessories. The integrated USB transceiver is a notable differentiator for cable-connected low-power peripherals. The combination of segment-LCD, USB, and Cortex-M0+ energy efficiency is uncommon at this price/performance tier. When designing with this part, allocate the exposed pad (EP) on the PCB as a solid copper pour connected to ground to meet thermal and electrical performance; route USB DP/DM as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the XTAL pins. Decouple VDD/VREFL/VREFH with 100 nF ceramics placed as close as possible to the respective pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL16Z64VFT4R

MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP MKL16Z64VFT4R is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB of SRAM, supplied in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. The Kinetis KL16 sub-family targets general-purpose low-power applications that need USB connectivity, segment-LCD support, and a richer analog peripheral set than the entry-level KL0x family, while preserving the KL0x energy-efficiency envelope. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a fixed set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M0+ core used here is the most energy-efficient member of the Cortex-M family, designed for deterministic real-time control in cost-constrained embedded products. The Kinetis family sits within NXP's broader portfolio of 32-bit microcontrollers, which in turn belongs to the larger category of microcontrollers and microprocessors (semiconductor -> IC -> MCU -> Kinetis -> KL1x). Key specifications include a 48 MHz maximum core clock, 64 KB program Flash, 8 KB SRAM, USB 2.0 full-speed device with on-chip transceiver, segment-LCD driver (up to 8x36 or 4x40 segments), 12-bit SAR ADC with up to 16 single-ended channels, low-power UART/SPI/I2C peripherals, and an operating voltage range of 1.71 V to 3.6 V. The device also integrates a low-power RTC, multiple low-power modes (VLLS0..3, LLS, VLPR, STOP), DMA, and a low-power timer for periodic wake-up. The 48-QFN exposed-pad package provides a low thermal resistance and a compact 7x7 mm footprint for space-constrained boards. Architecturally, the KL16 combines a Cortex-M0+ core, single-cycle I/O bus, and a peripheral bridge feeding independent timer, communication, and analog subsystems. The on-chip voltage regulator supports internal core supply from a single external 1.71-3.6 V rail, eliminating the need for multiple external supplies. Hardware AES is not present on this sub-family, but the segment LCD controller, USB FS device, and 12-bit ADC give it strong suitability for human-interface, metering, and consumer products. Typical applications include battery-powered sensor nodes, USB-CDC or USB-HID consumer accessories, small appliances with segment-LCD displays, electronic shelf labels, low-end smart meters, and portable medical accessories. The integrated USB transceiver is a notable differentiator for cable-connected low-power peripherals. The combination of segment-LCD, USB, and Cortex-M0+ energy efficiency is uncommon at this price/performance tier. When designing with this part, allocate the exposed pad (EP) on the PCB as a solid copper pour connected to ground to meet thermal and electrical performance; route USB DP/DM as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the XTAL pins. Decouple VDD/VREFL/VREFH with 100 nF ceramics placed as close as possible to the respective pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL17Z128VMP4

MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL17Z128VMP4 is a Kinetis KL17 ultra-low-power 32-bit microcontroller based on the ARM Cortex-M0+ core, operating at up to 48 MHz with 128 KB of flash and 32 KB of SRAM, housed in a 64-pin MAPBGA (5x5 mm) package. It targets battery-powered and energy-harvesting applications where active-mode performance and deep-sleep current must coexist in a small footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals such as timers, ADCs, and communication controllers. Cortex-M0+ parts occupy the ultra-low-power end of the ARM-M hierarchy and are typically used as microcontrollers -> embedded controllers -> semiconductor devices. The Kinetis KL1x family specifically adds segment-LCD controllers, USB-FS device, and richer analog compared to the entry-level KL0x line. Key features of the MKL17Z128VMP4 include a 16-bit SAR ADC with DMA support, 12-bit DAC, low-power timer, multiple low-power modes (VLLS0/1/3, LLPS, Stop, Wait, Run), flexible USB device (USB-FS) on selected variants, segment LCD controller up to 47 segments, and a 54 GPIO count. The 128 KB flash with 32 KB SRAM ratio makes it suitable for protocol stacks such as BLE HCI or Thread host layers while keeping peripheral support intact. Architecturally, the KL17 uses the Cortex-M0+ with a single-cycle multiplier and a 2-stage pipeline, achieving 0.93 DMIPS/MHz. The wide voltage range of 1.71 V to 3.6 V allows direct connection to single-cell Li-ion, coin cells, or regulated 3.3 V rails, while integrated DC-DC buck converter support simplifies multi-rail designs and improves efficiency in sleep modes where quiescent current drops below 1 uA. Typical applications include wearable fitness bands with segment-LCD displays, battery-powered wireless sensor nodes, USB-CDC/HID peripherals, industrial HMI panels with segment displays, and low-end home appliances. The combination of USB-FS, segment LCD, and low leakage makes the KL17 a strong fit for any 3.3 V coin-cell product that needs a bright display and a wired diagnostic port. When designing with this MCU, place the 0.1 uF decoupling capacitors as close as possible to each VDD/VSS pair and route the VBAT domain separately if a backup RTC battery is used. The segment-LCD bias network requires external charge-pump capacitors; insufficient capacitance leads to display ghosting at extreme temperatures below -20 C. This page synthesizes distributor pricing, drop-in Kinetis same-family alternatives, and practical design notes not consolidated on any single manufacturer page.

RFQ Contact
MKL17Z32VLH4 - 48MHz Cortex-M0+ MCU | NXP Semiconductors
MKL17Z32VLH4

MKL17Z32VLH4 - 48MHz Cortex-M0+ MCU | NXP Semiconductors

NXP Semiconductors MKL17Z32VLH4 is an ultra-low-power 32-bit Kinetis KL17 microcontroller featuring an Arm Cortex-M0+ processor, 48 MHz operating frequency, 32 KB Flash memory, and 8 KB SRAM in a 64-LQFP 10 x 10 mm package. It provides 54 general-purpose I/O pins and integrated I2C, SPI, UART/USART, I2S, FlexIO, PWM, DMA, and watchdog peripherals for compact embedded control systems. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals onto one package. The Kinetis KL1x family belongs to the Arm Cortex-M0+ microcontroller hierarchy and targets general-purpose, ultra-low-power designs. Its architecture supports efficient event-driven control while providing a familiar embedded software ecosystem for Arm-based development. Key device features include 32 KB of Flash for application code, 8 KB of SRAM for working data, and 54 available I/O pins. The integrated communication resources include I2C, SPI, UART/USART, and I2S, while FlexIO expands programmable serial-interface capability. PWM channels, DMA transfers, and a watchdog timer support efficient peripheral operation and system monitoring. The operating range includes 1.8 V, 2.5 V, and 3.3 V supply options. The Cortex-M0+ core combines a compact instruction set with efficient event-driven processing, making the MKL17Z32VLH4 appropriate for battery-powered sensors, portable instruments, and low-power control nodes. DMA reduces the CPU burden for serial transfers and data movement, while the watchdog contributes to recovery from unexpected faults. Program development is supported by Arm Keil and Keil Studio, as identified for this device by Arm Keil. Typical uses include low-power sensor hubs, industrial condition-monitoring nodes, connected meters, small motor-control modules, and compact consumer accessories. Serial interfaces allow the MCU to connect sensors, displays, storage devices, and host processors. FlexIO can implement additional communication formats when fixed-function peripherals do not satisfy the interface requirement. The 54 I/O pins provide substantial connectivity for LEDs, buttons, sensors, and discrete actuators in a 10 x 10 mm footprint. A primary design consideration is the difference between Flash and SRAM capacity. The 32 KB Flash must accommodate the boot code, application, configuration data, and firmware update requirements, while the 8 KB SRAM constrains simultaneous buffered data. Use the manufacturer pin-description table when assigning the 64 package pins and confirm the selected board configuration against the exact MKL17Z32VLH4 ordering code. Low-power operation also requires careful peripheral disablement, clock selection, and retention-policy configuration.

RFQ Contact
MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL17Z64VDA4

MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP MKL17Z64VDA4 is a 32-bit ultra-low-power microcontroller based on the ARM Cortex-M0+ core running at 48 MHz, with 64 KB flash memory and 16 KB SRAM, housed in a 36-ball XFBGA (MAPBGA-36) package measuring just 3.5 x 3.5 mm. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest level of the embedded computing hierarchy (MCU -> embedded processor -> microprocessor -> SoC). The Kinetis KL family from NXP sits in the ultra-low-power tier of this hierarchy, targeting battery-operated and space-constrained designs where every microamp of current matters. Key features of the MKL17Z64VDA4 include the energy-efficient Cortex-M0+ core, 64 KB (64K x 8) of on-chip flash program memory for firmware storage, 16 KB of SRAM for data and stack, and USB connectivity as noted on the NXP product page. The extremely small 36-XFBGA package with 0.5 mm ball pitch enables placement on the underside of dense PCBs, freeing board area for sensors, radios, or displays in wearables and IoT end nodes. Technically, the device belongs to the Kinetis KL1x general-purpose ultra-low-power family, which provides additional memory, communications, and analog peripheral options beyond the entry-level KL0x family. The 48 MHz Cortex-M0+ executes Thumb instruction set code with a two-stage pipeline, delivering efficient real-time control with a compact gate count and correspondingly low dynamic and static power consumption. Typical applications include battery-powered wearable devices, smart sensors and IoT end nodes, portable medical accessories, and compact human-interface controllers where small footprint and low standby power dominate the selection criteria. When designing with a 3.5 x 3.5 mm BGA, plan the PCB with via-in-pad or escape routing to all 36 balls, and budget rework capability carefully since BGA inspection requires X-ray equipment. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with all pricing referenced as of 2026-10-18.

RFQ Contact
MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL17Z64VFM4

MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL17Z64VFM4 is an ultra-low-power 32-bit microcontroller with a 48 MHz ARM Cortex-M0+ core, 64 KB of flash memory, USB 2.0 connectivity, and a 32-pin QFN 5 x 5 mm package. It is designed for compact embedded products that require efficient processing, low-power operation, and USB connectivity in a surface-mount footprint. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Kinetis KL1 series combines an ARM Cortex-M0+ core with embedded flash and a selection of serial, analog, timing, and communication peripherals. The MKL17Z64VFM4 belongs to the low-power Kinetis family intended for battery-operated and portable embedded applications. Its principal characteristics include a 32-bit ARM Cortex-M0+ processor operating at 48 MHz, 64 KB of flash, and USB 2.0 support. The 64 KB program-memory capacity is suitable for compact firmware, protocol stacks, control logic, and human-interface applications. The 32-QFN package also reduces board area compared with leaded packages while supporting high-density automated assembly. The 48 MHz Cortex-M0+ architecture provides a practical balance between processing throughput, deterministic control, and low power consumption. Because the processor is designed for embedded workloads, the device can execute control tasks, manage peripherals, and service USB communications without requiring an external microprocessor. Exact SRAM capacity, operating-voltage limits, peripheral configuration, and current-consumption figures should be confirmed in the manufacturer datasheet before a power-sensitive design is released. Typical applications include low-power USB accessories, portable instrumentation, compact control systems, battery-operated equipment, and embedded human-interface devices. In each case, the 64 KB flash allocation supports a meaningful firmware image while the QFN package simplifies integration into compact assemblies. USB 2.0 is particularly useful for configuration, data logging, firmware updates, and connection to a host controller. PCB implementation should follow the manufacturer's land pattern, exposed-pad soldering guidance, and decoupling recommendations exactly. Confirm the board footprint against the 32-pin QFN 5 x 5 mm drawing before layout release, and validate thermal performance at the highest intended operating temperature. Firmware development should use the appropriate Kinetis SDK, configuration tools, and a debug interface compatible with the selected device variant. This product record combines the verified identity, core architecture, memory capacity, frequency, USB capability, package, and lifecycle information with application guidance, replacement considerations, and design-oriented comparison data. It is intended to help engineers identify whether the MKL17Z64VFM4 matches the memory, connectivity, footprint, and low-power requirements of a new embedded design.

RFQ Contact
MKL17Z64VLH4 - 64KB Flash 48MHz Cortex-M0+ MCU | NXP
MKL17Z64VLH4

MKL17Z64VLH4 - 64KB Flash 48MHz Cortex-M0+ MCU | NXP

NXP Semiconductors MKL17Z64VLH4 is a general-purpose 32-bit Kinetis KL17 ultra-low-power microcontroller with an Arm Cortex-M0+ core, 48 MHz operating frequency, 64 KB of Flash memory, 16 KB of SRAM, USB connectivity, and a 64-LQFP 10 x 10 mm package. It combines a compact general-purpose MCU architecture with embedded memory and low-power operation for embedded control, connectivity, sensing, and portable applications. A microcontroller is a semiconductor device that integrates a processor core, program memory, volatile data memory, and peripherals into one package. The Kinetis KL1x family extends the low-power Kinetis KL0x family with additional memory, communications, and analog capabilities. The MKL17Z64VLH4 provides 64 KB of Flash for firmware and 16 KB of SRAM for working data, while its Arm Cortex-M0+ core supports efficient 32-bit control processing in a compact embedded footprint. Principal device features include the 48 MHz Cortex-M0+ core, 64 KB Flash, 16 KB SRAM, USB connectivity, and low-power operation. The 64-LQFP package exposes 64 pins on a 10 x 10 mm body, providing a practical surface-mount option for designs that require more I/O than smaller microcontroller packages. Its general-purpose positioning makes it suitable for control boards, sensor nodes, communication peripherals, and compact industrial equipment. The MKL17Z64VLH4 belongs to the Kinetis KL17 family, whose architecture is designed around efficient embedded processing rather than high-performance application computing. Its Cortex-M0+ instruction set supports typical interrupt-driven control, peripheral management, and communication tasks. The exact peripheral set, clock configuration, USB operating modes, and electrical limits must be confirmed against the relevant NXP datasheet and reference manual before a new PCB is released. Typical uses include low-power sensor interfaces, USB-connected peripheral controllers, compact automation equipment, and general-purpose embedded control modules. In each case, the 48 MHz processor provides timing margin for event handling, the Flash capacity accommodates application code, and the SRAM supports working buffers. USB connectivity can also simplify host-device designs that use standard USB controllers, cables, and update mechanisms. PCB design should preserve the package pin assignments and recommended decoupling layout defined by NXP. Provide a stable local supply, route high-current USB and clock paths carefully, and follow the NXP hardware design guidance for exposed power, ground, and signal connections. Validate oscillator, USB, and low-power behavior across the intended voltage and temperature conditions before production release.

RFQ Contact
MKL24Z32VLK4 - 48MHz Cortex-M0+ USB MCU | NXP
MKL24Z32VLK4

MKL24Z32VLK4 - 48MHz Cortex-M0+ USB MCU | NXP

The NXP Semiconductors MKL24Z32VLK4 is a 48 MHz ARM Cortex-M0+ Kinetis KL2 microcontroller with 32 KB of flash memory, 4 KB of SRAM, and full-speed USB 2.0 connectivity in an 80-pin LQFP 12 x 12 mm package. The device combines a compact general-purpose MCU architecture with USB device or USB On-The-Go functionality, making it suitable for connected control, data-acquisition, portable-instrument, and industrial interface designs. An ARM Cortex-M0+ microcontroller is a low-complexity, 32-bit embedded processor designed for cost-sensitive control systems. Within the product hierarchy, it belongs to the ARM Cortex-M family, then embedded processors, then microcontrollers and semiconductors. The Kinetis KL2 family adds USB connectivity to the ultra-low-power Kinetis KL1 architecture. This combination supports compact designs that need efficient control processing without a higher-performance Cortex-M4 core. The MKL24Z32VLK4 operates at 48 MHz and includes 32 KB of flash plus 4 KB of SRAM. Its USB 2.0 controller can operate as a full-speed USB device or as a USB On-The-Go host and device, depending on the selected family member and configuration. A 12-bit ADC, flexible GPIO, serial interfaces, timers, and low-power operating modes broaden its usefulness for embedded measurement, communication, and control tasks. The Kinetis architecture provides an efficient balance between processing performance, memory, and power consumption for battery-powered and space-constrained systems. Its Cortex-M0+ instruction set supports compact control code, while the dedicated USB controller handles protocol traffic without requiring a separate USB interface device. The 80-LQFP package also exposes a broad set of peripherals and debug functions for prototype development and production integration. Typical uses include USB-connected sensors, portable test equipment, industrial data loggers, low-power control panels, and USB-to-digital-interface adapters. In these systems, the MCU can acquire analog measurements, manage operator inputs, execute control logic, and communicate with a host computer over full-speed USB. The combination of 48 MHz processing and integrated USB simplifies the bill of materials compared with a discrete processor and USB bridge. PCB design should preserve short, controlled USB data paths and provide appropriate decoupling close to the power and ground pins. Follow the manufacturer pin-connection and layout guidance when assigning the 80-pin LQFP footprint, programming signals, clock sources, and analog inputs. Firmware must also account for USB enumeration, bus-power behavior, and the transition between active and low-power operating modes. This page consolidates the core device characteristics, same-package Kinetis alternatives, comparison parameters, and practical design guidance for engineers evaluating the MKL24Z32VLK4 in USB-enabled embedded systems. It also distinguishes the target from functional alternatives that require different packages, firmware changes, or PCB redesign.

RFQ Contact
MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VFT4

MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL24Z64VFT4 is a 48 MHz Arm Cortex-M0+ microcontroller with 64 KB of embedded flash memory, 8 KB of SRAM, and a full-speed USB 2.0 controller in a 48-QFN 7 x 7 mm package. It combines general-purpose embedded processing with USB connectivity and an ultra-low-power design intended for compact, low-energy embedded products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL24Z64VFT4 belongs to the Kinetis KL2x family, combining an Arm Cortex-M0+ core with USB 2.0 connectivity. This places it within the hierarchy of embedded processor, microcontroller, Kinetis L-series MCU, and low-power semiconductor, making it suitable for systems that require compact control and USB communication without a separate USB interface device. The device operates at up to 48 MHz and includes 64 KB of flash for firmware and 8 KB of SRAM for working memory. Its full-speed USB 2.0 capability supports USB device or OTG-oriented designs, while the Kinetis L-series integration includes analog and timing peripherals for embedded measurement and control. The 48-QFN package also exposes a compact land pattern for space-constrained PCB layouts. The Arm Cortex-M0+ architecture provides a straightforward low-complexity software platform for control loops, human-interface devices, portable instruments, and connected accessories. NXP describes the Kinetis KL2x family as pin, software, and tool compatible with other Kinetis L-series MCU families, supporting migration between related Kinetis designs. Firmware development therefore benefits from the broader Kinetis software ecosystem and reusable peripheral-driver patterns. Typical uses include low-power USB data loggers, compact sensor interfaces, USB-connected test equipment, and portable measurement instruments. A designer can place the MCU beside a sensor or transducer, run control and sampling routines from flash and SRAM, and use the integrated USB controller for configuration, data transfer, or firmware updates. The exact USB operating mode and peripheral allocation must be confirmed against the selected device configuration in the manufacturer datasheet. PCB implementation requires careful treatment of the exposed pad, power rails, decoupling, and USB signal routing. Keep the USB D+ and D- traces short and impedance-controlled, provide the decoupling network specified by the datasheet, and use a thermal-via pattern beneath the exposed pad when required by the PCB stack-up. Confirm all VDD, VDDUSB, VDDIO, ground, reset, and programming pins against the package drawing before fabrication. This page combines the exact MKL24Z64VFT4 identity and package information with lifecycle, pricing, sourcing, and interface details. It also organizes verified same-brand alternatives and practical implementation guidance for engineers comparing the KL2x family with adjacent Kinetis L-series devices.

RFQ Contact
MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP
MKL24Z64VLH4

MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP

The NXP Semiconductors MKL24Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built on the Arm Cortex-M0+ core, operating up to 48 MHz with 64 KB of embedded Flash memory (64K x 8 organization), 8 KB of SRAM, and a crystal-less full-speed USB 2.0 device controller, all housed in a 64-LQFP (10 x 10 mm) package. The device runs from a single 1.71 V to 3.6 V supply, so it fits industrial 3.3 V rails, 2.5 V legacy systems, and coin-cell powered portable products from the same design. A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, program memory, working RAM, and peripherals such as GPIO, timers, and communication controllers on one die. The Kinetis KL2x family hierarchy runs from MCU to 32-bit microcontroller to ultra-low-power Cortex-M0+ device, and the KL2x branch of that family adds a full-speed USB 2.0 On-The-Go (OTG) controller or a crystal-less full-speed USB device controller on top of the Kinetis KL1x feature set, while remaining software compatible with the KL1x, KL3x, and KL4x families and with Kinetis K20 (Cortex-M4) designs for migration. Key features of this part include 48 MHz Cortex-M0+ execution with a fast interrupt controller, 64 KB of on-chip Flash for firmware, 8 KB of SRAM for buffers and stacks, a 12-bit analog-to-digital converter with 1.71 V to 3.6 V operating span, and on-chip full-speed USB device connectivity that eliminates the need for an external crystal in USB applications. Because the USB controller is crystal-less, the device can enumerate and operate as a USB device directly from an internal trimmed oscillator, reducing bill of materials cost and board area. Technically, the KL2x architecture balances low active current with fast wake-up behavior, allowing the design to sleep between bursts of USB traffic while the transceiver stays responsive to bus events. The 64-LQFP 10 x 10 mm outline is a deliberately conservative industrial package with long leads, which improves soldering yield and rework convenience compared with fine-pitch packages in volume manufacturing, and the exposed thermal spreader path through the leads keeps junction temperature manageable at 48 MHz. Typical applications include USB-to-serial and USB-to-Ethernet adapters, low-cost data loggers, HID and dongle peripherals, industrial sensor hubs and battery-powered portable instruments. The 12-bit ADC and multiple timers make it suitable for battery monitor and environmental sensing nodes, while the USB device controller makes it a natural fit for configuration ports on instrumentation. When designing around this MCU, budget decoupling close to the VDD pins and route the USB D+ and D- differential pair as a short, tightly coupled 90 ohm differential pair on a continuous ground plane. Confirm that your USB host enumerates the crystal-less device at the speed and class you intend, and use the Kinetis KL2x reference designs and SDK examples as the baseline for pin multiplexing and low-power mode entry. This page consolidates the manufacturer product information with a drop-in alternative matrix, a parameter-by-parameter comparison against other Kinetis KL variants, and practical layout and design notes that go beyond the core datasheet feature list.

RFQ Contact
MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VLK4

MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP MKL24Z64VLK4 is a 32-bit Arm Cortex-M0+ Kinetis KL2 microcontroller operating up to 48 MHz, with 64 KB of embedded Flash memory, 8 KB of SRAM, and full-speed USB 2.0 connectivity. The device is offered in an 80-pin FQFP/LQFP package measuring 12 mm by 12 mm and is intended for compact, low-power embedded systems. Its operating supply range extends from 1.71 V to 3.6 V, with an industrial temperature range of -40 °C to +105 °C. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The MKL24Z64VLK4 belongs to the Kinetis KL2x family, which combines an Arm Cortex-M0+ processor with ultra-low-power design features and USB support. Its position within the broader hierarchy is Arm Cortex-M0+ embedded processor, 32-bit microcontroller, Kinetis MCU, and semiconductor. The KL2x family is positioned for low-power embedded applications requiring more connectivity than the earlier KL1x family. Key device characteristics include 64 KB of Flash for firmware, 8 KB of SRAM for working data, operation up to 48 MHz, a 12-bit analog-to-digital converter, and full-speed USB. The 80-pin package provides access to the family’s analog, timing, communication, and general-purpose I/O resources. The 1.71 V to 3.6 V operating range supports low-voltage portable, industrial, and connected embedded equipment, while the -40 °C to +105 °C rating supports temperature-controlled industrial environments. The Arm Cortex-M0+ core supports a compact instruction set and an event-driven architecture suited to control tasks, sensor monitoring, human-interface functions, and low-power background processing. Full-speed USB adds a practical path for connected peripherals, configuration tools, data logging, and firmware update workflows. Because the device combines USB and low-power operation, it can bridge host-device communication duties with embedded control rather than requiring a separate USB interface controller. Typical applications include USB-connected sensor nodes, industrial condition-monitoring equipment, compact data loggers, USB human-interface devices, industrial control panels, and low-energy embedded systems. The 64 KB Flash capacity is appropriate for moderate firmware loads, and the 8 KB SRAM is sufficient for typical control loops and small data buffers. Designs requiring substantially larger application code, extensive graphics storage, or complex protocol stacks should assess whether another MCU in the Kinetis portfolio offers more memory. When laying out the PCB, preserve the pin assignments and exposed-connection requirements defined by the manufacturer datasheet, especially for USB D+ and D− routing. Place USB differential traces as a controlled-impedance pair with minimal stubs and provide suitable decoupling near the power pins. Firmware development should use an NXP-supported toolchain and verify clock, reset, boot, and low-power configurations against the device reference manual before production. This product page consolidates the confirmed MCU specifications, package and supply information, lifecycle status, family context, sourcing options, and design-oriented selection guidance. It also distinguishes the 80-pin target from the 64-pin MKL24Z64VFM4 package variant so engineers can avoid an invalid footprint substitution.

RFQ Contact
MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP
MKL25Z128VLK4

MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP

The NXP Semiconductors MKL25Z128VLK4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating at 48 MHz, with 128 KB of flash memory and an 80-pin LQFP package measuring 12 x 12 mm. It is suited to embedded control, USB-connected sensing, portable instrumentation, and low-power edge systems. According to the distributor records, the device also provides 16 KB SRAM and full-speed USB. A microcontroller is a compact computer integrated with nonvolatile program memory, working RAM, digital peripherals, and I/O interfaces. It executes firmware, samples sensors, controls actuators, and manages communications without requiring a separate processor. The MKL25Z128VLK4 belongs to the hierarchy Kinetis KL25 microcontroller -> Arm Cortex-M0+ MCU -> 32-bit microcontroller -> embedded processor -> semiconductor. Its principal features include 128 KB of flash for firmware storage, 16 KB of SRAM for runtime data, a 48 MHz Cortex-M0+ core, and full-speed USB. The 80-LQFP package provides enough external connections for mixed-signal products, interface-heavy controls, and designs that favor a leaded package for inspection or assembly. The Kinetis KL2x family also supports migration paths across Kinetis KL1x, KL2x, KL3x, and KL4x devices, as stated by NXP. The Cortex-M0+ architecture favors energy-efficient embedded execution while retaining a conventional 32-bit instruction set and integrated interrupt handling. Flash capacity allows substantially larger applications than 64 KB-class devices, while SRAM supports packet buffers, sampled data, display or communication state, and real-time control tasks. USB integration can reduce the external controller count in connected products. Typical uses include USB data loggers, building-control endpoints, compact industrial monitors, sensor-hub boards, access-control terminals, and low-power portable instruments. The 48 MHz processing rate is suitable for concurrent USB traffic, control loops, protocol handling, and supervisory tasks where workload is modest enough not to require a higher-performance Cortex-M core. Designers should preserve the package pin assignments, supported supply ranges, decoupling requirements, and clock configuration when creating a PCB. The 80-LQFP footprint also requires adequate solder-mask clearance and inspection because its closely spaced leads can complicate manual rework. Firmware development should account for memory-map constraints, USB clocking, peripheral pin multiplexing, and low-power state transitions. This product page consolidates verified manufacturer and distributor identity data, sourcing links, application guidance, and compatibility analysis. Because the supplied sources do not expose complete electrical ratings, pricing values, or a verified pin list, missing fields are explicitly marked rather than inferred.

RFQ Contact
MKL25Z32VFM4 - 48MHz Cortex-M0+ 32KB Flash USB MCU | NXP
MKL25Z32VFM4

MKL25Z32VFM4 - 48MHz Cortex-M0+ 32KB Flash USB MCU | NXP

NXP Semiconductors MKL25Z32VFM4 is a 32-bit ARM Cortex-M0+ Kinetis KL2 microcontroller operating at up to 48 MHz with 32 KB of flash memory and 4 KB of SRAM, housed in a 32-HVQFN (5 x 5 mm) surface-mount QFN package. It integrates a full-speed USB 2.0 On-The-Go controller, which makes it one of the smallest USB-capable low-power MCUs available. A microcontroller (MCU) is a single integrated circuit containing a CPU core, memory, and peripherals on a single die. The ARM Cortex-M0+ architecture used here is a compact, low-cost 32-bit processor defined by the Arm Architecture Compact Instruction set, intended for cost-sensitive embedded control. In the Kinetis family hierarchy the MKL25Z32VFM4 sits in the KL2 sub-family, which extends the KL1x line by adding a full-speed USB 2.0 OTG controller or a full-speed crystal-less USB 2.0 device controller. That positioning makes it a natural fit for USB-connected sensors, dongles, and low-power data acquisition nodes. Key features include a 48 MHz Cortex-M0+ core, 32 KB (32K x 8) on-chip flash for program storage, 4 KB of SRAM for working memory, and a full-speed USB 2.0 device/OTG controller that can be clocked from an internal oscillator, removing the need for an external crystal when precision timing is not required. The part is offered in a 32-HVQFN 5 x 5 mm package with a 0.5 mm pitch, allowing a very small board footprint for USB dongles and wearable accessories. Technically, the KL2 sub-family is designed for ultra-low-power operation: the core sleeps with a low active current and the part can be clocked from the internal 8 MHz oscillator trimmed to USB accuracy, saving both board area and BOM cost. The KL25 series is source-compatible with the Kinetis K20 (Cortex-M4) MCUs and with the rest of the Kinetis KL1x, KL2x, KL3x and KL4x families, giving a clear migration path when a design outgrows its memory budget or peripheral set. The reference manual covering MKL25Z32VFM4 and its siblings is document KL25P80M48SF0RM. Typical applications include USB-to-serial adapters, HID and CDC class dongles, low-power environmental sensing nodes, battery-operated portable measurement instruments, USB-connected battery chargers, and compact industrial data acquisition modules where a full-size 48 MHz Cortex-M4 would be unnecessary. When designing around this device, pay attention to the exposed-pad ground connection and the USB D+/D- routing. The 5 x 5 mm HVQFN has a limited thermal escape area, so for sustained high clock rates with USB traffic, pour a full ground plane beneath the package and keep the USB trace pair short, 50-ohm differential-impedance controlled, and free of test-point stubs. This page consolidates manufacturer part data, package and memory details, drop-in same-footprint alternatives in the 32-QFN 5 x 5 mm land pattern, and practical layout and USB routing guidance into a single engineering reference that goes beyond a distributor catalogue listing.

RFQ Contact
MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL25Z32VLK4

MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL25Z32VLK4 is a 32-bit Kinetis KL2 microcontroller with a 48 MHz Arm Cortex-M0+ core, 32 KB of flash memory, 4 KB of SRAM, and full-speed USB support in an 80-pin LQFP package measuring 12 x 12 mm. The device belongs to the Kinetis KL2x ultra-low-power family and supports operation from 1.8 V, 2.5 V, or 3.3 V supply levels. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The Arm Cortex-M0+ core provides a compact, energy-efficient architecture for embedded control, while the Kinetis family extends this core with low-power operating modes, general-purpose I/O, communication peripherals, and USB connectivity. In the system hierarchy, the MKL25Z32VLK4 is a microcontroller, semiconductor, and programmable embedded-control component. Key features include a 48 MHz operating frequency, 32 KB flash organized as 32K x 8, and 4 KB SRAM. The KL2x family adds a full-speed USB 2.0 controller, with the selected device identified as supporting full-speed USB OTG. Its 80-LQFP package provides 80 external terminals, making it suitable for designs that need broader peripheral access than smaller MCU packages can offer while avoiding a ball-grid-array assembly. The MKL25Z32VLK4 is based on the Arm Cortex-M0+ instruction set, which prioritizes compact code size and efficient real-time control rather than high-performance computing. Its 32 KB flash stores the application firmware, while 4 KB SRAM supports stack space, variables, buffers, and USB or serial-data handling. The manufacturer describes the Kinetis KL2x family as ultra-low-power and notes compatibility with other Kinetis KL1x, KL2x, KL3x, and KL4x devices for migration paths, subject to peripheral and pin-level review. Typical applications include USB-connected data acquisition, compact control panels, industrial sensor nodes, wearable accessories, and embedded USB peripherals. The 48 MHz Cortex-M0+ core is useful for responsive control tasks, and the integrated USB controller can simplify connectivity compared with a discrete USB interface. A board-level design still needs suitable voltage regulation, clocking, decoupling, USB routing, and firmware configuration. Designers should match the exact 80-pin LQFP footprint and verify peripheral assignments, USB implementation details, and board-level connectivity against the NXP documentation before layout. Stable supply voltage and correctly sized local decoupling are fundamental because processor and USB activity can produce fast transient current. USB signal routing also requires controlled impedance and careful placement of the protection and termination network. This product page combines the exact NXP and distributor identification, distinguishes verified electrical facts from unspecified details, identifies same-family migration candidates, and highlights PCB, power, and USB design considerations that help engineers evaluate the MKL25Z32VLK4 beyond a basic catalog description.

RFQ Contact
MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL25Z64VFM4

MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP Semiconductors MKL25Z64VFM4 is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 48 MHz, with 64 KB of flash memory, 8 KB of SRAM, and full-speed USB support in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device combines a low-power MCU architecture with analog and digital peripherals for compact embedded systems. A microcontroller is an integrated circuit that executes embedded software, reads sensor inputs, controls actuators, and manages communication interfaces. The MKL25Z64VFM4 belongs to the Kinetis KL2 ultra-low-power MCU family, placing it within the hierarchy of embedded microcontroller, ARM Cortex processor, and low-power embedded-system device. Principal features include a 48 MHz ARM Cortex-M0+ core, 64 KB of flash organized as 64K by 8 bits, and 8 KB of SRAM. The part also includes a full-speed USB controller, analog and digital peripherals, and support for 1.8 V, 2.5 V, and 3.3 V operation. Its 32-pin HVQFN package supports dense PCB layouts without relying on a large leaded package. The Kinetis KL2 architecture is designed for embedded applications where processing capability, USB connectivity, and low-power operation must coexist in a compact footprint. The 64 KB flash capacity provides room for bootloader code, application firmware, configuration data, and USB device functions, while the 8 KB SRAM allows real-time tasks and peripheral buffering without external memory. Typical uses include USB-connected sensors, compact data loggers, industrial interface modules, portable measurement equipment, and low-power embedded controllers. The full-speed USB interface can simplify connection to a host system, while the Cortex-M0+ core provides a common architecture for firmware development and peripheral control. PCB design should account for the exposed pad beneath the HVQFN package, provide adequate thermal and electrical grounding, and place decoupling capacitors close to the supply pins. USB routing requires careful control of trace geometry and return paths, and firmware should use the manufacturer's clock, power-management, and USB initialization procedures. This product page combines the core Kinetis KL25 specifications, package information, design guidance, and qualified drop-in alternatives to support component selection, firmware planning, PCB layout, and replacement decisions without requiring engineers to reconstruct the design context from separate documents.

RFQ Contact
MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors
MKL25Z64VLH4

MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors

NXP Semiconductors MKL25Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating up to 48 MHz. It provides 64 KB of Flash memory, 8 KB of SRAM, integrated full-speed USB connectivity, and a 64-LQFP 10 mm × 10 mm package for compact embedded systems. A microcontroller is a semiconductor device that integrates a processor core, programmable memory, peripheral interfaces, and power-management functions on one package. The Cortex-M0+ core combines a compact instruction set with efficient exception handling for embedded control. Within the product hierarchy, the MKL25Z64VLH4 belongs to the Kinetis L series of ultra-low-power microcontrollers, combining general-purpose control, serial connectivity, and USB device or OTG-oriented functions. The 48 MHz maximum operating frequency supports responsive control loops and efficient handling of embedded workloads, while 64 KB of Flash preserves room for firmware, configuration data, and application code. The 8 KB SRAM supports working memory, stack allocation, buffering, and communication tasks without requiring an external memory interface in typical designs. Full-speed USB integration enables direct peripheral connectivity for data acquisition, configuration, logging, and human-interface applications. The device supports 1.8 V, 2.5 V, and 3.3 V operating configurations according to the product listing information. This voltage flexibility makes it suitable for mixed-voltage embedded systems, although power-supply sequencing, decoupling, and signal-level limits must be checked against the manufacturer datasheet before implementation. Its ultra-low-power positioning is useful for systems that spend substantial time idle, sleep, or operating at reduced clock rates. Typical applications include USB-connected data loggers, industrial interface modules, compact control boards, portable measurement equipment, and low-power embedded products. The 64-LQFP package exposes more general-purpose I/O than smaller microcontroller packages and remains practical for automated assembly, inspection, and prototype rework. Software development is supported through the wider Kinetis ecosystem, subject to the exact peripheral configuration of the selected device. PCB design should preserve short return paths for digital supplies and sensitive analog inputs, place decoupling capacitors close to their associated supply pins, and keep high-current or switching-node connections away from communication and measurement traces. USB routing also requires controlled impedance, suitable trace geometry, and compliance with the applicable device and interface-layout requirements in the manufacturer datasheet. This product overview consolidates the principal device identity, memory capacity, clock rate, USB capability, package information, sourcing guidance, and design considerations into a compact engineering reference for initial component selection and PCB planning.

RFQ Contact
MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL26Z128CAL4R

MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL26Z128CAL4R is a Kinetis KL26 sub-family 32-bit ARM Cortex-M0+ microcontroller running up to 48 MHz, integrating 128 KB of flash and 16 KB of SRAM, with a full-speed USB 2.0 device controller (crystal-less capable), and packaged in a compact 36-ball WLCSP measuring approximately 2.37 mm x 2.46 mm. It is one of the lowest-power Kinetis Cortex-M0+ MCUs in NXP's ultra-low-power portfolio, designed for portable and battery-powered applications where PCB real estate is at a premium. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and GPIO. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for deterministic interrupt response and minimal gate count. Microcontrollers sit at the heart of embedded systems, providing local intelligence for sensors, actuators, user interfaces, and connectivity functions across consumer, industrial, and IoT markets. Key features of the MKL26Z128CAL4R include the Cortex-M0+ core with single-cycle multiplication, an integrated low-power USB 2.0 full-speed device controller that eliminates the need for an external crystal, multiple low-power modes (Run, Wait, Stop, VLPR, VLPW, VLPS, LLS, VLLSx), a 12-bit SAR ADC, high-speed analog comparators, a real-time clock, and a flexible low-power timer (LPTMR). The device supports 1.71 V to 3.6 V supply operation and is offered in a tiny 36-ball WLCSP for space-constrained designs such as wearables and USB dongles. The MKL26Z128CAL4R uses a 32-bit ARMv6-M architecture with the Thumb/Thumb-2 instruction set, giving it strong code density while keeping silicon area small. Its multi-mode low-power architecture allows peripherals like the ADC and comparators to operate in low-power modes independently of the CPU, reducing total system energy. The inclusion of an integrated USB PHY with on-chip 3.3 V regulator and a 1 kHz low-power timer makes it attractive for always-on, event-driven products. Typical applications include USB HID peripherals (keyboards, mice, game controllers), wearable fitness bands, BLE/ZigBee host microcontrollers, sensor hub MCUs, low-end medical sensors, and compact IoT end nodes. The crystal-less USB and tiny WLCSP package make it especially attractive for USB dongles, gaming peripherals, and other form-factor-constrained consumer electronics. When designing with the MKL26Z128CAL4R, pay attention to the WLCSP PCB layout - the 0.4 mm ball pitch requires HDI PCB manufacturing and careful via.2.3 pad design for reliable assembly. Provide adequate decoupling (one 100 nF and one 4.7 uF X5R ceramic) within 2 mm of the power pins to maintain supply integrity during USB transitions. This page synthesizes distributor pricing, drop-in alternatives within the same WLCSP-36 footprint, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
MKL26Z128VMC4 - 48MHz Cortex-M0+ 128KB USB MCU | NXP
MKL26Z128VMC4

MKL26Z128VMC4 - 48MHz Cortex-M0+ 128KB USB MCU | NXP

The NXP MKL26Z128VMC4 is a Kinetis KL2x 32-bit microcontroller with an ARM Cortex-M0+ core running at 48 MHz, 128 KB flash memory, and a full-speed USB 2.0 On-the-Go (OTG) controller, housed in a 121-ball MAPBGA (8x8 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals to execute dedicated embedded control tasks. Within the power/efficiency hierarchy of embedded processors, the Kinetis KL2x family sits in the ultra-low-power MCU segment, extending the KL1x series with USB connectivity while remaining compatible with Kinetis K20 (Cortex-M4) and other KL-series devices, providing a clear migration path. Key features include the 48 MHz Cortex-M0+ core optimized for low dynamic power, 128 KB of program flash, USB OTG plus crystal-less full-speed USB device operation, and 84 general-purpose I/O lines. Connectivity spans I2C, LINbus, SPI, UART/USART, and USB; system peripherals include DMA, I2S, PWM, brown-out detect/reset, low-voltage detect, power-on reset, and a watchdog timer. Technically, the Cortex-M0+ architecture delivers ARM code density with a two-stage pipeline and low gate count, while the KL2x power architecture provides multiple low-power modes with fast wake-up, making it suitable for battery-powered USB peripherals. The mixed-signal integration (I2S, 12/16-bit ADC capability per family documentation) supports audio and sensor aggregation designs. Typical applications include USB HID device peripherals, wearable and portable battery-powered products, sensor hubs, and small HMI systems. The 121-ball 8x8 mm MAPBGA keeps board area compact while exposing 84 I/Os. Design consideration: the MAPBGA-121 footprint requires controlled-impedance fine-pitch BGA layout; plan an escape-routing layer strategy early. The USB OTG controller removes the need for an external crystal in device mode, saving BOM cost. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MKL26Z256VMC4 - 48MHz ARM Cortex-M0+ MCU 256KB Flash | NXP
MKL26Z256VMC4

MKL26Z256VMC4 - 48MHz ARM Cortex-M0+ MCU 256KB Flash | NXP

The NXP Semiconductors MKL26Z256VMC4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL2x sub-family, integrating 256KB of flash memory and operating at a core frequency of 48 MHz. It is housed in a 121-pin MAPBGA (8x8 mm) package designed for ultra-low-power portable applications with on-chip full-speed USB 2.0 device or OTG support. The device targets battery-sensitive designs that need a Cortex-M0+ core with USB connectivity, segment LCD drivers, and a rich analog peripheral set. What is a Kinetis microcontroller? A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based 32-bit microcontrollers from NXP Semiconductors designed for ultra-low-power embedded applications. The KL2x sub-family specifically adds a full-speed USB 2.0 controller (device or OTG) on top of the KL1x baseline, while maintaining the same Cortex-M0+ architecture and low-leakage power modes. This positions Kinetis MCUs in the broader product hierarchy as: ARM Cortex-M0+ -> Kinetis L series -> Kinetis KL2x sub-family -> NXP 32-bit microcontrollers -> embedded microcontrollers -> semiconductors. Key features of the MKL26Z256VMC4 include 256KB of on-chip flash, up to 32KB of SRAM, a full-speed USB 2.0 device/OTG controller with on-chip transceiver and 3.3V voltage regulator, a 12-bit SAR ADC with up to 16 single-ended channels, multiple low-power modes (VLLS0/1/3, LLS, VLPR, Wait, Stop), and segment LCD drivers capable of driving 8x36 or 4x40 segments. The 121-MAPBGA (8x8 mm) package provides high I/O density suitable for compact wearable and sensor-hub designs. Architecturally, the MKL26Z256VMC4 leverages the Cortex-M0+ core's Thumb-2 instruction set with a single-cycle multiplier and a 4-stage pipeline optimized for low active current (around 4 mA typical run current). On-chip peripherals include multiple low-power timers, an RTC, I2C, SPI, UART, FlexIO for flexible serial emulation, and a low-power segment LCD controller. The integrated 3.3V USB regulator eliminates the need for an external LDO on the USB bus. Typical applications span wearable health and fitness devices, USB HID peripherals (keyboards, game controllers, sensors), portable medical devices, industrial sensor hubs, and battery-powered IoT edge nodes. Its combination of USB, segment LCD, and Cortex-M0+ efficiency makes it well suited to battery-powered human-machine interface products. When designing with the MKL26Z256VMC4, ensure the 121-MAPBGA land pattern uses NSMD pads with proper via-in-pad or tented-via PCB design, place the 12 MHz or 16 kHz crystal load capacitors close to the XTAL pins, and follow NXP's hardware design guidelines for USB-OTG PHY routing (90 ohm differential, length matching, and a clean ground plane). Decouple VDD with 100 nF plus 4.7 uF bulk capacitors near each supply pin. This page synthesizes NXP manufacturer specifications, distributor pricing, drop-in alternatives, and practical PCB design guidance not found in any single datasheet - giving engineers a single, citable reference for evaluating the MKL26Z256VMC4 against USB-capable Cortex-M0+ microcontrollers from competing vendors.

RFQ Contact
MKL26Z32VFT4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL26Z32VFT4

MKL26Z32VFT4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL26Z32VFT4 is a 32-bit Arm Cortex-M0+ Kinetis KL2-series microcontroller operating at up to 48 MHz, with 32 KB of Flash memory and 4 KB of SRAM in a 48-pin QFN package measuring 7 x 7 mm. It includes full-speed USB 2.0 OTG connectivity, multiple serial interfaces, and an integrated low-voltage regulator for compact embedded systems. A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and I/O in one integrated circuit. The Arm Cortex-M0+ core provides a compact, energy-efficient architecture commonly used in cost-sensitive embedded control products. Within the product hierarchy, this device is a general-purpose microcontroller, part of the Kinetis KL2 family, and designed for applications that need real-time control, serial connectivity, data acquisition, and USB connectivity without a higher-cost application processor. The principal specifications include a 48 MHz maximum clock, 32 KB (32K x 8) embedded Flash, 4 KB (4K x 8) SRAM, and a 32-bit Arm Cortex-M0+ processor core. USB 2.0 OTG support adds full-speed peripheral and host-device interface capability. An integrated low-voltage regulator supports the MCU's internal supply requirements, while the collection of serial interfaces enables communication with sensors, displays, wireless modules, and external transceivers. The MKL26Z32VFT4 belongs to the Kinetis L family, whose devices are positioned for pin, software, and tool compatibility across compatible family members. This compatibility can simplify firmware maintenance, peripheral design, and qualification across multiple product variants. Its operating-temperature information identifies a -40°C to 105°C ambient range, making it suitable for industrial and extended-temperature embedded equipment when the application also satisfies the device's complete electrical and environmental requirements. Typical applications include USB-connected data loggers, compact industrial controllers, sensor-hub boards, wearable and accessory interfaces, building-control nodes, and USB-to-serial products. The 32 KB Flash footprint is suitable for compact control firmware, while the Cortex-M0+ core handles peripheral servicing, protocol processing, and low-power state management. USB can reduce connector count when the product must exchange data with a host while retaining a small board area. Designers should select decoupling, oscillator, reset, and USB routing according to the manufacturer reference design and datasheet. The exposed pad beneath the QFN requires a properly designed thermal and ground structure, while USB differential routing should use controlled geometry and a continuous reference plane. Confirm the exact pin assignment and exposed-pad connection in the manufacturer datasheet before laying out or modifying a PCB. This product page combines device specifications, lifecycle information, sourcing guidance, compatibility analysis, and practical design considerations. It also identifies verified same-footprint alternatives and highlights the engineering differences that matter when evaluating a replacement for an existing Kinetis KL2 design.

RFQ Contact
MKL26Z32VLH4 - Kinetis KL26 48MHz Cortex-M0+ MCU, 32KB Flash, USB | NXP
MKL26Z32VLH4

MKL26Z32VLH4 - Kinetis KL26 48MHz Cortex-M0+ MCU, 32KB Flash, USB | NXP

The NXP Semiconductors MKL26Z32VLH4 is a Kinetis KL2x family 32-bit microcontroller built on the ARM Cortex-M0+ core, running up to 48 MHz, with 32 KB of program flash and integrated full-speed USB 2.0 (OTG or crystal-less device) in a 64-pin LQFP (10x10 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. Within the broader semiconductor taxonomy, the MKL26Z32VLH4 sits in the hierarchy MCU -> 32-bit MCU -> ARM Cortex-M MCU -> low-power MCU -> Kinetis family. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for cost-sensitive embedded applications where deterministic interrupt response and low active/idle power matter more than raw compute. Key features include 32 KB flash, 4 KB SRAM, a full-speed USB 2.0 controller with on-chip transceiver, a low-power ARM Cortex-M0+ core, segment LCD controller (SLCD) option on related variants, multiple low-power modes (run, wait, stop, VLPRMPVLLS3), and a flexible low-power peripheral set including 12-bit ADC, 16-bit timers, LPUART, I2C, SPI, and USB. The device also integrates an internal 32 kHz and 8 MHz reference, simplifying BOM and supporting crystal-less USB operation in the KL2x sub-family. Architecturally, the KL26 leverages Freescale/NXP's low-leakage process and a tightly coupled Cortex-M0+ pipeline with a single-cycle I/O port, achieving CoreMark/mW efficiency that puts it ahead of many 8-bit MCUs while retaining 32-bit throughput. The 48 MHz core mark, combined with hardware multiply/divide, gives roughly 0.93 DMIPS/MHz. Typical applications include USB HID peripherals (keyboards, mice, remotes), wearable fitness bands, low-cost data loggers, sensor hubs, and battery-powered IoT end nodes. The on-chip USB 2.0 FS controller eliminates external PHY cost, and the 32 KB flash is adequate for HID class drivers, basic USB stacks, and small application logic. When designing, note that the KL26 requires NXP's Kinetis Design Studio or MCUXpresso toolchain; an external decoupling scheme of 0.1 uF + bulk VHF per VDD/VREF domain is recommended, and the USB DP/DM traces must be 90 ohm differential matched. This page synthesizes distributor pricing, drop-in pin-compatible Kinetis alternatives, and practical design notes beyond the manufacturer datasheet to help engineers make faster, more confident sourcing decisions.

RFQ Contact
MKL26Z64VFM4 - 48MHz Cortex-M0+ 64KB USB MCU | NXP
MKL26Z64VFM4

MKL26Z64VFM4 - 48MHz Cortex-M0+ 64KB USB MCU | NXP

The NXP Semiconductors MKL26Z64VFM4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller running at up to 48 MHz, with 64 KB flash, 8 KB of SRAM, and a full-speed USB 2.0 device controller with crystal-less USB operation, housed in a 32-pin HVQFN (5x5 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, sitting at the heart of embedded systems. Within the power-management hierarchy of embedded semiconductors, the Kinetis KL2x family belongs to NXP's Kinetis L series of ultra-low-power MCUs built on the ARM Cortex-M0+ core, the most energy-efficient member of the ARM Cortex-M processor line. Key features include the 48 MHz Cortex-M0+ core with single-cycle fast GPIO, 64 KB of on-chip flash memory and 8 KB of SRAM, and a full-speed USB 2.0 On-the-Go controller. Uniquely in this class, the KL2x sub-family adds a crystal-less USB device controller, eliminating the external crystal and its cost for USB device applications. The part operates from a 1.8 V, 2.5 V, or 3.3 V supply, supporting battery-powered designs. The KL26 architecture leverages NXP's low-leakage process technology with multiple low-power modes, allowing the core, peripherals, and clocks to be independently gated for microamp-level sleep currents. The comprehensive peripheral set includes serial communication interfaces (UART, SPI, I2C), ADC, and TPM timers. Typical applications include portable and battery-powered devices, USB HID devices and USB sensors, human-interface equipment, and small industrial control nodes where USB connectivity and low power are essential. Design consideration: the crystal-less USB feature requires proper reference-clock configuration per NXP application notes; verify USB compliance in your final layout. Plan flash and SRAM budgets early, since 8 KB of RAM is modest for stacks plus USB buffers. This page synthesizes distributor availability, pin-compatible alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ Contact
MKL26Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL26Z64VFT4

MKL26Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP MKL26Z64VFT4 is a 32-bit ARM Cortex-M0+ Kinetis KL2 microcontroller operating up to 48 MHz, with 64 KB of flash memory and a USB device controller, housed in a 48-QFN package measuring 7 mm by 7 mm. It is designed for compact, energy-efficient embedded systems that require USB connectivity and a low-power 32-bit processing architecture. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, peripherals, and communication interfaces on one device. The MKL26Z64VFT4 belongs to the Kinetis KL2x family, an ultra-low-power MCU family positioned for battery-powered instruments, human-interface devices, industrial controls, and connected accessories. Its USB capability distinguishes it from basic microcontrollers intended only for general embedded control. Key features include an ARM Cortex-M0+ core, a maximum operating frequency of 48 MHz, 64 KB of flash, and a full-speed USB device controller. The 64 KB of flash provides room for firmware, configuration data, and boot code, while the Cortex-M0+ core supports efficient event-driven control. The specified operating temperature range of -40 °C to +105 °C covers industrial temperature requirements, although the complete electrical limits must be checked against the manufacturer datasheet for the exact suffix and grade. The MKL26Z64VFT4 uses a 48-QFN 7 mm by 7 mm package, enabling a compact surface-mount layout with short signal paths. USB and general-purpose I/O are particularly useful for data acquisition modules, configuration interfaces, human-interface equipment, and low-power peripherals. Because the device is a microcontroller rather than a fixed-function interface controller, firmware can consolidate protocol handling, control logic, timing, and peripheral coordination into one component. Typical applications include USB-connected sensors, programmable measurement modules, compact control boards, industrial human-interface terminals, and energy-efficient embedded accessories. In these systems, the 48 MHz processing rate supports responsive control loops, the flash capacity supports moderate application firmware, and the USB device controller can simplify direct connectivity to a host computer or USB interface circuit. PCB implementation should follow the manufacturer’s QFN land pattern and pin-assignment table. Keep USB routing short, provide the specified power and decoupling network, and route high-current or sensitive analog functions away from digital switching nodes. Confirm oscillator, USB, and I/O requirements for the exact board configuration before releasing the layout. This page combines the NXP product identity, distributor catalog specifications, package details, application guidance, and same-package family alternatives into a compact engineering reference. It also highlights the decisions that matter when replacing or redesigning around the MKL26Z64VFT4, including core, memory, USB, package, and temperature constraints.

RFQ Contact