Microcontrollers

Products (20,000+)

Z86C9325VSG - 25MHz 8-Bit ROMless MCU | Zilog
Z86C9325VSG

Z86C9325VSG - 25MHz 8-Bit ROMless MCU | Zilog

Zilog Z86C9325VSG is an 8-bit ROMless Z8-series microcontroller with a 25 MHz clock, 24 I/O ports, and a 2.97 V to 5.5 V operating supply range in a 44-pin PLCC package. It targets embedded control designs requiring an external program and data memory while retaining the Z8 peripheral architecture. A microcontroller is a programmable semiconductor that integrates a CPU core, memory interface, I/O ports, timers, and communication peripherals on one device. The Z86C9325VSG belongs to the Z8 family of 8-bit embedded controllers and is positioned as a general-purpose embedded-control component for industrial, consumer, and communications equipment. The controller combines a 25 MHz maximum clock with an 8-bit data bus and 24 I/O ports. Its 2.97 V to 5.5 V supply range supports both 3.3 V and 5 V system designs. The ROMless configuration permits firmware and data to be stored in external memory, providing greater design flexibility than a device with fixed internal program memory. The Z86C93 architecture includes a hardwired 16-bit by 16-bit multiplier, a 32-bit by 16-bit divider, and three 16-bit counter timers. A capture register and fast decrement mode support additional measurement and control functions. These resources can reduce external logic in motor, counter, signal-processing, and timing-oriented embedded systems. Typical uses include industrial controllers, appliance-control boards, communications equipment, keypad and panel interfaces, and compact embedded systems that need moderate processing speed with numerous I/O connections. External memory is required when program storage exceeds any external-memory configuration selected for the design, and the system must account for the controller’s external address and data interfaces. Layout planning should preserve access to all 44 PLCC terminals and route sensitive clock and reset signals away from noisy switching nodes. Power, decoupling, programming, and clock requirements should be implemented according to the Z86C93 manufacturer datasheet. Because this is a ROMless controller, firmware availability, boot behavior, and external-memory sizing determine whether it remains a practical upgrade option. This page combines the Z86C9325VSG specifications with package details, engineering applications, verified drop-in references, and practical selection guidance. It is designed to help engineers assess clock rate, voltage compatibility, external-memory requirements, pin count, and lifecycle status before committing a new PCB design.

RFQ Contact
Z86C9333ASG - 33MHz 8-Bit ROMless MCU | Zilog
Z86C9333ASG

Z86C9333ASG - 33MHz 8-Bit ROMless MCU | Zilog

The Zilog Z86C9333ASG is an 8-bit ROMless Z8 microcontroller operating at 33 MHz, supplied in a 48-pin LQFP package measuring 7 x 7 mm. Its 4.5 V to 5.5 V operating-voltage range suits 5 V embedded control systems where an 8-bit processor must combine straightforward peripheral integration with deterministic control performance. The part is identified as part of the C93 microcontroller family. An 8-bit microcontroller is a compact embedded processor designed to execute control instructions from externally supplied program memory. The ROMless architecture places code in external memory rather than an internal masked-ROM array, allowing the same controller to be used with different program-storage arrangements. Within the product hierarchy, the Z86C9333ASG is an embedded microcontroller, an integrated circuit, and a semiconductor intended for industrial automation, instrumentation, and equipment-control applications. The principal operating specifications are a 33 MHz clock, an 8-bit CPU architecture, and a 4.5 V to 5.5 V supply range. The device also incorporates a multiplier and divider capability according to the product description. These functions make it useful in control systems that need arithmetic scaling, frequency generation, timing measurement, or peripheral clock division without relying on a higher-cost processor architecture. The Z86C9333ASG uses a 48-pin LQFP package, providing a comparatively high pin count for an 8-bit controller and supporting connection of multiple external interfaces and memory devices. Its 7 x 7 mm body keeps the component practical for compact industrial control boards. The package exposes the controller's external program-memory interface, general-purpose I/O, and other device functions through a surface-mount footprint requiring careful signal-integrity and layout planning. Typical uses include industrial controllers, data-acquisition equipment, programmable logic controllers, instrumentation, and embedded automation modules. A designer may select this device when the application fits an 8-bit control model but requires external program memory, moderate processing speed, and extensive I/O. It can also serve as a dedicated subsystem controller alongside another processor when peripheral management or timing functions dominate the design. PCB implementation should prioritize a short, continuous ground return beneath the device and careful routing of clock, reset, and external-memory signals. Decoupling capacitors should be placed directly beside the relevant supply pins, while external program-memory routing should minimize propagation delay between the controller and memory components. Before release, verify the exact pin assignments, electrical timing, and power requirements against the Zilog datasheet. This product page combines the Z86C9333ASG's confirmed operating characteristics, application guidance, sourcing information, and design considerations in a format that helps engineers evaluate the controller before beginning PCB layout or firmware development.

RFQ Contact
Z86C9333FSC - 33MHz 8-Bit ROMless MCU | Zilog
Z86C9333FSC

Z86C9333FSC - 33MHz 8-Bit ROMless MCU | Zilog

Zilog Z86C9333FSC is a 33 MHz, 8-bit Z8 ROMless microcontroller with 236 x 8 bytes of RAM, 24 I/O lines, three 8-bit timers, UART/USART support, and EBI/EMI connectivity in a 44-pin LQFP package measuring 10 x 10 mm. Its 33 MHz operating speed provides higher throughput than conventional low-speed 8-bit controllers while retaining the simple Z8 architecture and external program-memory interface. An 8-bit microcontroller is a compact processor designed to execute embedded control logic from program memory and maintain operating state in RAM. The Z86C9333 belongs to the broader embedded-controller hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor. A ROMless architecture means the device contains no internal program ROM, so firmware must be supplied through an external memory interface. This architecture is useful when programs, firmware revisions, or memory sizes must remain flexible. The verified feature set includes ROMless operation at 33 MHz, 236 bytes of RAM, 24 I/O lines, three 8-bit timers, UART communication, and EBI/EMI interfaces. The 44-LQFP surface-mount package exposes substantially more signal pins than small dual-inline packages, supporting parallel external memory and additional peripheral connectivity while remaining compatible with automated PCB assembly. The Z86C9333 architecture is intended for embedded control rather than high-compute workloads. Its external program-memory interface allows the stored firmware size to be established outside the MCU, while its three timers support periodic counting, timing, and event generation. UART/USART communication enables connection to host systems, sensors, or other controllers, and EBI/EMI provides an external bus-oriented path for additional devices. Typical applications include industrial keypad controllers, serial data concentrators, instrumentation interfaces, embedded control panels, and compact automation modules. In these systems, the 33 MHz speed can improve response to serial traffic and control tasks, while the 24 I/O lines reduce the need for separate I/O expanders. The ROMless configuration is particularly valuable when the same MCU platform must cover several firmware versions or board configurations. Designers must account for external program-memory timing, address decoding, bus contention, and required support components when using the ROMless configuration. PCB layout should minimize routing delay and preserve signal integrity on external bus and UART lines. Software must also provide the vector table and reset behavior expected by the external memory system. Because the verified data does not state supply voltage, timing margins, or detailed pin assignments, those values should be confirmed in the manufacturer documentation before schematic capture. This product page consolidates verified distributor specifications, same-package replacement information, application guidance, and design cautions. It distinguishes confirmed Z86C9333FSC characteristics from unavailable electrical details so procurement and engineering decisions can be made without inventing package, pin, or lifecycle information.

RFQ Contact
Z86C9333VSG - 8-Bit 33MHz ROMless MCU | IXYS
Z86C9333VSG

Z86C9333VSG - 8-Bit 33MHz ROMless MCU | IXYS

The IXYS Z86C9333VSG is an 8-bit, 33 MHz ROMless Z8-series microcontroller packaged in a 44-lead J-leaded LCC measuring 16.6 mm by 16.6 mm. It operates from a 4.5 V to 5.5 V supply and is intended for embedded control systems requiring an external memory interface, compact surface-mount construction, and a moderately high operating clock. A microcontroller is a programmable semiconductor that integrates a CPU, memory interfaces, I/O ports, timers, and peripheral functions on one device. The Z8 family belongs to the broader hierarchy of 8-bit microcontrollers, embedded processors, semiconductor integrated circuits, and electronic control components. A ROMless configuration means the device does not contain its final program storage internally; an external memory device is therefore part of the complete embedded design. Key characteristics include the 8-bit CPU architecture, 33 MHz maximum clock, ROMless program-memory architecture, and 4.5 V to 5.5 V operating supply. Its 44-LCC J-lead package supports compact industrial, consumer, and embedded-control assemblies without relying on a fine-pitch BGA package. The package is identified as surface-mount technology and uses J-shaped terminals designed for board attachment and mechanical inspection. The device is specifically described as a Z8-series microcontroller and as an embedded controller. Its operating architecture allows firmware and data to be organized in external memory, which can provide flexible field-programmable behavior, reusable platform designs, and separation between application code and the microcontroller package. At 33 MHz, the processor is suited to control loops, human-interface tasks, protocol handling, and supervisory functions that require more scheduling headroom than a basic low-speed microcontroller. Typical applications include industrial machine controls, instrumentation panels, motor and actuator supervisory systems, building-control interfaces, programmable logic controllers, and compact embedded control products. The 4.5 V to 5.5 V supply range is suitable for regulated 5 V system rails. Designs should provide suitable external program and data memory, power decoupling, oscillator circuitry, and a reset arrangement appropriate to the selected Z8 memory interface. The primary engineering consideration is that ROMless operation requires additional memory and careful bus implementation. Place the external memory, controller, and associated routing as a coordinated subsystem, following the pin-description and reference-circuit guidance in the manufacturer datasheet. Confirm signal timing and memory-map compatibility before PCB release because the CPU clock, external memory access, and I/O behavior must operate as one consistent design. This page consolidates verified package, clock, supply, architecture, and lifecycle information into an engineering-oriented product record. It also separates confirmed Z86C9333VSG characteristics from unresolved memory and peripheral details, compares related Z8 devices, and highlights practical verification steps for external-memory, decoupling, and pinout decisions.

RFQ Contact
Z86C9533VSC - CMOS Z8 DSP Microcontroller | Zilog
Z86C9533VSC

Z86C9533VSC - CMOS Z8 DSP Microcontroller | Zilog

Zilog Z86C9533VSC is a CMOS Z8 microcontroller with an embedded digital signal processor, combining general-purpose microcontroller control with dedicated DSP processing in a 84-pin leadless chip carrier package. It belongs to the Z8 family of highly integrated embedded controllers designed for applications requiring both digital control and real-time signal processing. The Z86C95 architecture is ROMless, allowing program storage and boot code to be implemented in external memory. A digital signal processor, commonly abbreviated as DSP, is a semiconductor architecture optimized for operations used in signal processing, including multiplication, accumulation, filtering, waveform generation, and spectral analysis. The Z8 MCU hierarchy combines a conventional embedded-control environment with an embedded DSP engine. This integration can reduce the need for separate processor packages when a system must perform control functions and process sampled or generated signals concurrently. The principal identifiable features of the Z86C9533VSC are its CMOS construction, Z8 single-chip microcontroller architecture, embedded DSP processor, ROMless configuration, and 84-pin LCC package. Its integration is useful when a product needs deterministic embedded control alongside digital signal-processing functions. Exact processor clock, memory, I/O, electrical limits, temperature range, and package dimensions must be confirmed against the manufacturer datasheet before schematic capture or firmware development. The Z86C9533VSC belongs to the Z86C95 MCU family, which combines microcontroller functionality with an embedded DSP processor. A ROMless architecture generally requires external program memory, so designers should plan the memory interface, reset behavior, bus timing, and firmware loading method as an integrated part of the system architecture rather than treating memory as an afterthought. Firmware development also requires the correct Z8 toolchain, device programming method, interrupt configuration, and peripheral initialization sequence. Typical uses include digital audio and communications, industrial signal conditioning, motor and motion control, communications equipment, and embedded systems that combine a control loop with real-time waveform processing. The LCC-84 format provides many external connections compared with a small leaded microcontroller package, making it suitable for systems requiring multiple peripheral, bus, and control signals while still allowing board-level miniaturization. PCB implementation requires careful attention to exposed-pad or thermal requirements if present, supply decoupling, signal integrity, and programming access. Because this is a fine-pitch leadless package, verify land geometry and assembly tolerances against the manufacturer package drawing. A new design should also confirm peripheral multiplexing and pin assignments in the datasheet rather than inferring them from the larger Z8 family. This product page organizes the available Z86C9533VSC identity, packaging information, sourcing path, and engineering considerations. It also separates documented facts from unverified numeric details, helping engineers move from part selection to datasheet verification without relying on assumptions about clock speed, memory size, or electrical performance.

RFQ Contact
Z86E0308PSG - 8-Bit Z8 OTP MCU, 8MHz | Zilog
Z86E0308PSG

Z86E0308PSG - 8-Bit Z8 OTP MCU, 8MHz | Zilog

The Zilog Z86E0308PSG is an 8-bit Z8 CMOS microcontroller with 512 bytes of one-time-programmable memory, an 8 MHz operating frequency, and support for 3.3 V or 5 V operation. It is packaged in an 18-pin PDIP. The device belongs to the Zilog Z8 family of small-format embedded microcontrollers designed for cost-sensitive control, monitoring, and simple peripheral-control applications. Its compact memory footprint, integrated digital control functions, and dual-voltage operation make it suitable for designs that need deterministic control without a larger application-specific processor. An OTP microcontroller stores programmed logic permanently, so the Z86E0308PSG is appropriate for finished products whose control firmware does not need field updates. The Z8 architecture uses an 8-bit instruction-oriented design and is commonly used for appliance controls, industrial interfaces, sensor conditioning systems, and embedded automation equipment. Its 3.3 V and 5 V capability helps designers support multiple supply environments without changing the controller family. The manufacturer identifies the Z86E0308PSG as an 8-bit MCU with 512-byte OTP memory and an 8 MHz maximum operating frequency. The 18-pin PDIP package provides a through-hole option for prototypes, educational designs, and production assemblies where leaded components are preferred. Because the exact peripheral allocation, electrical limits, pin names, and timing details are not listed in the retrieved product descriptions, engineers should use the Zilog Z86E03/E06 CMOS Z8 OTP Microcontrollers datasheet for the definitive pinout and timing reference. Typical implementations include simple motor and relay controllers, temperature and industrial monitoring units, keyboard interfaces, LED status panels, and low-cost embedded equipment. The 512-byte OTP limit is most suitable for compact control loops rather than protocol-heavy gateways, data logging, or applications requiring substantial RAM. In those designs, the MCU can handle discrete input decisions, timing, and peripheral coordination while external components provide sensing, actuation, communications, or power regulation. For a new layout, verify the 18-pin PDIP footprint, oscillator requirements, reset behavior, input thresholds, and programming procedure against the manufacturer datasheet before committing the PCB. Use the Request a Quote form on this page to request current commercial availability, lead time, and ordering information.

RFQ Contact
Z86E0308SSG - 8-Bit 8MHz OTP Microcontroller | Zilog
Z86E0308SSG

Z86E0308SSG - 8-Bit 8MHz OTP Microcontroller | Zilog

Zilog Z86E0308SSG is an 8-bit Z8 microcontroller with 512 bytes of one-time-programmable memory, an 8 MHz operating frequency, and a 3 V to 5.5 V supply range. The device is packaged in an 18-pin SOIC with a 300 mil body width for through-hole assembly compatibility. It combines a compact embedded-control footprint with OTP program memory for cost-sensitive, low-volume embedded products. An 8-bit microcontroller is a compact computing device designed to execute control logic, monitor inputs, and drive outputs within appliances, instruments, and industrial equipment. The Z86E0308SSG belongs to the Z8 microcontroller family, combining a processor core, OTP program memory, timers, and serial I/O in one package. This architecture suits sequential control tasks where deterministic behavior and low component count matter more than high-bandwidth processing. Principal characteristics include an 8 MHz clock, 512 bytes of OTP program memory, and operation across a 3 V to 5.5 V supply range. Its 18-pin SOIC-18-300mil package supports conventional PCB assembly and inspection. The industrial temperature classification, gull-wing terminal arrangement, and rectangular package geometry are useful constraints when laying out a new board or sourcing a mechanically similar replacement. The Z8 architecture is intended for embedded control rather than high-volume data processing. One-time-programmable memory makes the programmed version of the device suitable for products whose firmware does not require field updates. Because the memory cannot be rewritten after programming, production programming, blank-device handling, and firmware revision control must be planned before devices reach the assembly line. Typical uses include small appliance controllers, instrumentation front ends, industrial control modules, sensor interfaces, and dedicated timing or sequence-control products. In these applications, the MCU can evaluate digital inputs, operate timers, update displays, and communicate with external peripherals while keeping the external component count and board area modest. When designing a board, verify the exact pin assignments, port capabilities, oscillator requirements, and programming interface against the manufacturer datasheet before routing signals. The 300 mil SOIC body is wider than a narrow 150 mil SOIC, so component clearance, connector placement, and assembly tooling must accommodate the specified package rather than a generic 18-pin footprint. This page consolidates distributor specifications, package constraints, drop-in comparison information, and application-level engineering guidance. It also distinguishes documented parameters from values that must be confirmed with Zilog before schematic release, helping designers move from part selection to a controlled PCB and firmware implementation.

RFQ Contact
Z86E0412PEG - 8-Bit 12MHz OTP MCU | Zilog
Z86E0412PEG

Z86E0412PEG - 8-Bit 12MHz OTP MCU | Zilog

Zilog Z86E0412PEG is an 8-bit Z8 CMOS microcontroller operating at up to 12 MHz, with 1 KB of one-time-programmable program memory, 125 bytes of RAM, and 14 I/O pins in an 18-pin DIP package. It is intended for compact control systems that require deterministic embedded control in a low-pin-count through-hole package. A microcontroller is a programmable semiconductor containing a processor core, program memory, data memory, and peripherals on one integrated circuit. The Z8 family combines an 8-bit CPU architecture with resources suited to appliance controls, industrial controllers, and small production systems. The Z86E0412PEG belongs to the one-time-programmable segment of this family, providing a practical path to firmware development and low-volume manufacturing without requiring a user-programmed flash-memory interface. The principal specifications include a 12 MHz maximum operating frequency, 1 KB of OTP program memory organized as 1K x 8, 125 bytes of RAM, and 14 I/O lines. Its operating supply range is 4.5 V to 5.5 V, while the specified temperature range extends from -40°C to +105°C. The DIP-18 package supports conventional through-hole PCB assembly and is useful when socketed prototyping, manual service, or legacy manufacturing processes are preferred. Its one-time-programmable architecture allows application firmware to be permanently written during production, providing a field-programmable appearance during development without a costly external programming interface. This is especially useful for small embedded products where the firmware does not need to be changed after deployment. Because OTP memory cannot be erased, revision control and production programming procedures should be planned carefully before a product reaches manufacturing. Typical applications include temperature or level control, small actuator controllers, appliance interfaces, discrete sensor-conditioning systems, and simple embedded control panels. The 14 I/O count provides useful connectivity for switches, indicators, relays, and digital sensors, while the 125-byte RAM can hold variables and short-lived state. Designers should verify peripheral availability, interrupt requirements, and timing behavior against the manufacturer datasheet for each selected function. The main design consideration is programming and validation. Develop the firmware on the target Z8 architecture, test production programming in a repeatable fixture, and verify every programmed image before release. The 4.5 V to 5.5 V supply requirement also means that the power source and all attached I/O devices must remain within compatible voltage levels. A 5 V supply with suitable local decoupling is the straightforward baseline when designing around this controller. This product page combines the core Z86E0412PEG specifications, commercial sourcing guidance, package information, application guidance, and the available drop-in comparison. It is designed to help engineers identify the correct Z8 controller, plan programming and PCB assembly, and determine whether the directly replaceable Z86E0412PEC variant satisfies the project requirements.

RFQ Contact
Z86E0412SEG - 8-Bit 12MHz 1KB OTP MCU | Zilog
Z86E0412SEG

Z86E0412SEG - 8-Bit 12MHz 1KB OTP MCU | Zilog

Zilog Z86E0412SEG is an 8-bit Z8 microcontroller with a 12 MHz clock, 1 KB of one-time-programmable memory, 14 I/O ports, and an 18-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and is specified for operation from -40°C to +105°C. The Z86E0412SEG combines a compact OTP MCU architecture with the Z8 family’s integrated peripherals and low-cost single-chip design. What is an 8-bit microcontroller? An 8-bit microcontroller is a programmable integrated circuit containing a central processing unit, nonvolatile program memory, data memory, and input/output peripherals on one chip. The Z86E0412SEG belongs to the Z8 family of MCUs, a semiconductor subtype of embedded controller. Its OTP program memory permits a device to be programmed once during manufacturing or prototype preparation, making it practical for cost-sensitive products with stable firmware. The principal characteristics include an 8-bit processor, 12 MHz operating speed, 1 KB of OTP memory organized as 1K × 8, and 14 I/O ports. Its 4.5 V to 5.5 V operating range accommodates conventional 5 V equipment, while the -40°C to +105°C rating supports industrial environments. The 18-pin SOIC-18, 300 mil package is also identified by some listings as an 18-pin plastic DIP-family package. Z86E0412SEG is a Zilog Z8 CISC controller intended for compact embedded-control tasks. One-time-programmable storage distinguishes it from field-reprogrammable Flash MCUs, eliminating the need for nonvolatile memory that can be updated after programming. The 14 I/O ports provide external control and monitoring points, while the 12 MHz clock supports time-dependent control, debouncing, signal sequencing, and communication tasks within the device’s stated limits. Typical applications include appliance controllers, small motor or relay-control boards, industrial interface modules, lighting controllers, instrumentation peripherals, and legacy equipment upgrades. Its combination of limited memory, 14 I/O ports, and a wide temperature range is well suited to simple control systems where the application does not require large firmware images or extensive connectivity. The OTP architecture is particularly appropriate when firmware will not change after deployment. Designers should verify oscillator configuration, pin multiplexing, and programming requirements against the Zilog datasheet before committing the PCB footprint. Because OTP memory cannot be rewritten, firmware validation and device programming must be complete before production programming. Decoupling should follow the manufacturer’s recommended power-network layout, and unused inputs should be configured to avoid unnecessary current consumption. This product page consolidates the Z86E0412SEG specifications, package information, family alternatives, and application-oriented design guidance. It also identifies the practical migration limits associated with one-time-programmable memory, helping engineers distinguish true family options from MCU replacements that require software and hardware requalification.

RFQ Contact
Z86E0612PSG - 12MHz 8-Bit OTP MCU with 1KB | Zilog
Z86E0612PSG

Z86E0612PSG - 12MHz 8-Bit OTP MCU with 1KB | Zilog

The Zilog Z86E0612PSG is an 8-bit Z8 microcontroller with a 12 MHz maximum operating frequency, 1 KB of one-time-programmable program memory, and 125 bytes of RAM in an 18-pin plastic DIP package. The device includes SPI connectivity, a power-on reset, a watchdog timer, and 14 general-purpose I/O pins. Its 3 V to 5.5 V supply range supports both 3.3 V and 5 V embedded systems. An 8-bit microcontroller is a compact processor architecture intended for control-oriented products in which modest computational performance, deterministic peripheral access, and low system complexity are more important than high bandwidth. The Z8 family combines the processor core, nonvolatile program memory, RAM, I/O, timing functions, and serial communications in one integrated circuit, reducing the component count required for embedded control, appliance control, industrial interfaces, and compact consumer products. The Z86E0612PSG centers on a Z8 CPU operating at up to 12 MHz. Its 1 KB OTP program memory is intended for compact control code that can be programmed once during manufacturing. The 125-byte RAM provides working storage for variables, state machines, and communication buffers. Fourteen I/O pins allow the device to operate as the central controller for digital inputs, outputs, indicators, and external interface signals. Communication and system-control peripherals broaden the device beyond simple GPIO control. The integrated SPI interface supports synchronous serial communication with sensors, displays, memories, and other SPI-compatible peripherals. A power-on reset establishes a known startup state, while the watchdog timer helps recover operation after a software fault. Together, these resources make the MCU appropriate for compact products whose firmware must remain small and whose board area is constrained. Typical applications include appliance control, simple sensor-hub controllers, LED and display interfaces, industrial control modules, access-control equipment, and compact embedded products. The 12 MHz operating speed provides useful responsiveness for interrupt-driven control loops, while the 1 KB memory limit strongly favors event-driven firmware, state-machine architecture, and code reuse. The 18-pin DIP package also facilitates prototyping and straightforward through-hole assembly. PCB planning should preserve access to the SPI interface, I/O pins, reset behavior, and programming or test points. Because program memory is OTP, firmware validation and production programming must occur before the component reaches the end customer. Developers should also budget for decoupling close to the supply pins and verify all external serial-device logic levels against the 3 V to 5.5 V operating range. This page consolidates the Z86E0612PSG electrical identity, package details, drop-in replacement candidates, application guidance, and design considerations into an engineering-focused reference. It supports part selection and board planning while helping teams distinguish confirmed device characteristics from parameters that still require confirmation from the manufacturer datasheet.

RFQ Contact
Z86E0612SSG - 8-Bit 12MHz 1KB OTP MCU | Zilog | Embedded Control
Z86E0612SSG

Z86E0612SSG - 8-Bit 12MHz 1KB OTP MCU | Zilog | Embedded Control

The Zilog Z86E0612SSG is an 8-bit Z8 microcontroller with a 12 MHz operating frequency, 1 KB of one-time-programmable program memory, and 124 bytes of RAM in an 18-pin SOIC package. It includes SPI connectivity, Power-On Reset, and a Watchdog Timer, making it suitable for compact embedded control, communication, and peripheral-control designs. An 8-bit microcontroller is a programmable semiconductor that integrates a central processing unit, memory, and peripherals into one device. The Z8 core follows the broader hierarchy of microcontroller, embedded processor, processor, and semiconductor. Compared with a general-purpose processor, this device targets smaller control systems where compact code and memory, deterministic peripheral control, and low system complexity are more important than application-processor performance. The Z86E0612SSG's principal features are its 12 MHz operating frequency, 1 KB OTP program memory, 124-byte RAM, SPI interface, Power-On Reset, and Watchdog Timer. The 1 KB OTP architecture suits final-production programs that do not require repeated field reprogramming. SPI provides a compact serial path for sensors, display controllers, memory devices, and other peripherals, while the Watchdog Timer supports recovery from unexpected program stalls. Its Z8 core is implemented as an 8-bit CISC microcontroller. Program execution, data storage, and peripheral interaction are integrated into one device, reducing the number of external components required for a small embedded controller. The 124-byte RAM provides working memory for variables and stack operations, while the OTP program memory imposes a fixed one-time programming constraint that should be considered before committing the device to a production design. Typical applications include small sensor-interface controllers, SPI peripheral hubs, industrial control modules, appliance control boards, and compact communication equipment. In these systems, the MCU can supervise a sensor or actuator, exchange data through SPI, and use its reset and watchdog functions to support stable operation after power application or a firmware fault. Design the power rail and signal paths around the manufacturer's electrical limits, and place the required bypass capacitors close to the supply pins. Because program memory is OTP, validate the complete firmware image and programming sequence during production testing. Confirm the exact pin functions, input thresholds, timing limits, and clock requirements in the Zilog manufacturer datasheet before releasing the PCB layout. This page consolidates the core Z86E0612SSG specifications, sourcing guidance, replacement considerations, and practical implementation notes into an engineering-focused resource that supports faster design review and production planning.

RFQ Contact
Z86E0812PEG - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E0812PEG

Z86E0812PEG - 8-Bit 12MHz OTP Microcontroller | Zilog

Zilog Z86E0812PEG is an 8-bit Z8 microcontroller operating at up to 12 MHz, with 2 KB of one-time-programmable memory, 14 I/O ports, a 4.5 V to 5.5 V supply range, and an 18-pin PDIP package. It is designed for compact embedded-control systems requiring straightforward 8-bit processing, dedicated I/O, and firmware retention without a separate external memory device. An 8-bit microcontroller is a programmable semiconductor containing a processor core, memory, I/O ports, and supporting peripherals on one integrated circuit. The Zilog Z8 family belongs to the broader embedded-controller hierarchy that includes microcontrollers, embedded processors, and semiconductors. Compared with a general-purpose processor, this device targets smaller control loops where cost, simplicity, deterministic peripheral access, and board area are more important than complex computation or high memory bandwidth. Key verified specifications include a 12 MHz maximum clock speed, 2 KB of OTP program memory, 14 I/O ports, and a 4.5 V to 5.5 V operating supply range. Its operating temperature spans -40°C to +105°C, making it suitable for industrial-temperature equipment when the associated system design and qualification requirements are satisfied. The RoHS designation identifies the part as compliant with the supplied RoHS listing, while other regulatory classifications remain unconfirmed in the available data. The device uses the Z8 architecture described in the available product listings as an eZ8 CISC microcontroller. One-time-programmable memory is intended for firmware that does not require later field rewriting, helping control production complexity when the final program is known before deployment. The 14 I/O pins provide interfaces for digital inputs, output control, or mixed peripheral functions, while the 18-pin PDIP format supports conventional through-hole assembly and prototyping. Typical applications include small industrial controllers, sensor-interface modules, building-control products, appliance-control boards, and compact embedded instruments. The 12 MHz clock is appropriate for moderate-speed digital sequencing, while the 14 available I/O ports can connect switches, indicators, relays, and discrete sensing components. Because the part has 2 KB of OTP rather than large RAM or Flash, firmware should be sized carefully and peripheral-heavy tasks delegated to dedicated devices when necessary. The primary design consideration is validating the exact pin assignments, oscillator requirements, reset behavior, and programming procedure against the official manufacturer documentation before layout release. Designers should also confirm current consumption and timing behavior for the selected external clock and operating conditions, because those values were not established by the supplied verification data. DIP packaging requires adequate insertion clearance, mechanical support, and protection from electrostatic discharge during handling. This product page consolidates verified distributor specifications, lifecycle information, package details, commercial availability links, and practical application guidance. It also distinguishes verified Zilog family drop-in options from unverified cross-brand replacements so engineers can make a sourcing decision without treating general cross-reference tools as proof of pin and firmware compatibility.

RFQ Contact
Z86E0812SEG - 8-Bit 12MHz 2KB OTP MCU | Zilog
Z86E0812SEG

Z86E0812SEG - 8-Bit 12MHz 2KB OTP MCU | Zilog

The Zilog Z86E0812SEG is an 8-bit Z8 OTP microcontroller operating at 12 MHz with 2 KB of one-time-programmable program memory, 14 I/O ports, a 4.5 V to 5.5 V supply range, and an 18-pin SOIC package. It is intended for compact embedded-control products where economical one-time programming, deterministic peripheral control, and a small package are useful. The Z86E0812SEG is listed as active by the supplied datasheet listing and is positioned for low-volume, cost-sensitive controller designs. An OTP microcontroller is a single-chip embedded controller whose program memory is written once during manufacturing or provisioning. It belongs to the Z8 family and the broader microcontroller hierarchy that includes general-purpose MCUs, embedded controllers, ROM devices, and flash-memory devices. Unlike a flash MCU, the OTP architecture eliminates repeated in-circuit programming, which can simplify production tooling while fixing the installed firmware permanently. Applications must therefore treat programming as a manufacturing step rather than a field-update mechanism. The three principal selection parameters are the 12 MHz operating clock, 2 KB of OTP program memory, and 4.5 V to 5.5 V operating supply. The device also provides 14 I/O ports, making it suitable for compact products that read sensors, operate indicators, drive logic-level peripherals, and perform basic sequencing. Its 8-bit architecture and 18-pin SOIC form factor support space-constrained boards where a larger microcontroller package would be unnecessary. The Z8 family provides an established platform for embedded-control applications, but the supplied excerpts do not expose detailed timer, serial-interface, oscillator, or electrical-limit tables. The part should therefore be selected using the complete Zilog datasheet rather than inferred from the distributor summaries. In particular, engineers should confirm oscillator connection requirements, reset behavior, I/O drive limits, and programming procedure before committing a PCB or production fixture to this device. Typical uses include simple appliance controllers, building-control modules, industrial interface boards, LED sequencing systems, instrumentation front ends, and small motor or relay-control products. A 5 V supply keeps the device compatible with conventional embedded logic, while the limited 2 KB program memory favors compact control loops, state machines, and dedicated peripheral handling rather than general-purpose applications requiring extensive firmware storage. The primary design consideration is OTP irreversibility. Firmware must be thoroughly validated before programming because later corrections normally require a new programmed device rather than an in-circuit reflash. Board designers should also follow the datasheet's recommended bypass-capacitor and clock-network arrangements, and production engineers should build programming, test, and traceability steps into the manufacturing process. This page consolidates the verified distributor specifications, package information, sourcing links, alternative-family comparison, and practical OTP design considerations. It also distinguishes confirmed data from parameters that still require verification from the complete manufacturer datasheet, helping engineers make a defensible decision before committing the Z86E0812SEG to a design.

RFQ Contact
Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog
Z86E3016PEG

Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog

The Zilog Z86E3016PEG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable memory in a 28-pin plastic dual-inline package. The verified product listings identify the device as the Z8 family member Z86E3016PEG and describe it as an 8-bit, 16 MHz microcontroller with 4K × 8 OTP program memory and UART capability. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The Z8 belongs to the 8-bit microcontroller hierarchy, where each CPU cycle operates on an 8-bit data word. Such devices are used to read inputs, execute embedded control logic, and operate outputs in products where a compact controller, deterministic behavior, and modest processing requirements are more important than high computational throughput. The Z86E3016PEG's principal verified characteristics are its 16 MHz operating frequency, 8-bit CPU architecture, 4 KB OTP memory, and 28-pin PDIP package. The Mouser listing characterizes the device as an 8-bit MCU with 8K OTP and UART support, while the DigiKey listing identifies 4 KB, expressed as 4K × 8. Because these distributor descriptions express the OTP organization differently, engineers should confirm the exact program-memory organization against the manufacturer datasheet before assigning firmware capacity. The Z8 architecture is suitable for embedded motor-control, appliance-control, industrial-control, and serial-interface designs where an 8-bit CPU and UART simplify the control system. OTP program memory provides a one-time programmable implementation medium for products whose firmware is finalized before deployment. A 28-pin PDIP package also supports conventional through-hole assembly, prototyping, and manual inspection rather than requiring a fine-pitch surface-mount process. Before finalizing a design, verify the device's exact pin assignments, electrical limits, oscillator options, I/O count, UART characteristics, current consumption, and timing requirements using the manufacturer datasheet. Those parameters are not fully present in the supplied distributor snippets and are therefore marked as needed rather than estimated. Confirm that the 16 MHz clock source and UART baud-rate requirements can be met by the selected oscillator and external support components. This page combines verified distributor specifications, package information, pricing evidence, and explicitly qualified replacement analysis for the Z86E3016PEG. It also distinguishes verified drop-in candidates from unsupported cross-package options, helping engineers evaluate procurement and redesign decisions without treating package similarity as proof of functional equivalence.

RFQ Contact
Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog
Z86E3016PSG

Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog

Zilog Z86E3016PSG is an 8-bit Z8-family microcontroller with 16 MHz operating frequency, 4 KB of one-time-programmable program memory, 237 bytes of RAM, and 24 I/O pins in a 28-pin package. It is designed for cost-sensitive embedded-control applications that require simple programming, low-power wake-up behavior, and dedicated on-chip peripherals. A microcontroller is a programmable semiconductor that integrates a CPU, memory, I/O ports, timers, and support circuitry on one chip. The Z8 architecture belongs to the broader microcontroller and embedded-processor hierarchy. Compared with application-specific controllers, an OTP microcontroller offers a straightforward way to implement fixed control logic in appliances, security devices, HVAC equipment, and other compact electronic products. Verified device features include one-time-programmable memory, enhanced wake-up circuitry, programmable watchdog timers, and selectable low-noise EMI options. The 16 MHz operating speed provides processing headroom for simple digital control, while 24 I/O lines allow the device to connect to sensors, switches, indicators, and actuators. Two 8-bit timers support periodic events, timing delays, and basic event generation without requiring additional timing components. The 4 KB OTP program memory is organized as 4K by 8 bits, and the device includes 237 bytes of RAM for working data. OTP memory permits the final application firmware to be programmed once, making the controller well suited to production products whose control logic does not require field updates. This simplifies manufacturing compared with flash-programmable alternatives, but it also means a firmware revision generally requires a new programmed device rather than an in-system memory update. Typical uses include appliance controls, security-system peripherals, temperature and process-control equipment, HVAC modules, and compact industrial controllers. The 24 available I/O pins simplify designs that need multiple digital inputs and outputs, while the watchdog timer helps recover operation after faults or unexpected program flow. Enhanced wake-up circuitry supports low-power systems that must respond to external activity without maintaining continuous high activity. Designers should verify the exact package pinout, operating voltage, clock configuration, and programming procedure against the Zilog datasheet before layout. The provided search data confirms a 28-pin device but does not expose authoritative pin names or a complete manufacturer PDF URL, so those details remain marked as data needed rather than being inferred. Firmware and board design should also account for OTP programming limitations and the watchdog timeout behavior.

RFQ Contact
Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E3016SSG

Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog

The Zilog Z86E3016SSG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable program memory, 125 bytes of RAM, and 24 I/O lines in a 28-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and is specified for a 0°C to 70°C ambient-temperature range. A microcontroller is an integrated circuit that combines a processor core, nonvolatile program memory, working RAM, and peripherals on one semiconductor device. The Z86E3016SSG belongs to the Z8 family of 8-bit microcontrollers and provides a compact control platform for products that require deterministic digital control but do not need the processing power, memory, or peripheral complexity of a 32-bit embedded processor. Its one-time-programmable architecture is intended for production devices whose firmware does not need field reprogramming. The principal device characteristics include a 16 MHz clock, 4 KB OTP program memory organized as 4K by 8 bits, 125 bytes of RAM, and 24 general-purpose I/O lines. Integrated power-on reset and watchdog-timer functions support dependable startup and recovery behavior. The 28-pin surface-mount SOIC package supports conventional PCB assembly while providing enough I/O capacity for sensors, indicators, control inputs, and external logic. The Z8 processor architecture provides an 8-bit execution model optimized for control-oriented embedded systems. At 16 MHz, it offers substantially greater timing headroom than many simpler 8-bit controllers, while the compact instruction and memory architecture keeps firmware and peripheral integration straightforward. Programmable OTP options include an RC oscillator and EPROM protection, allowing the selected configuration to be fixed according to the product's operating requirements. Typical uses include appliance controllers, industrial control modules, security and access-control equipment, instrumentation peripherals, and small embedded control subsystems. In each case, the 24 available I/O lines and 125 bytes of RAM are important constraints. Designers should allocate RAM carefully for stacks, buffers, and intermediate state, while treating the 4 KB OTP capacity as the final firmware limit. The primary design consideration is that one-time-programmable memory cannot be changed after programming. Firmware validation, programming fixtures, and production traceability therefore must be completed before devices reach end users. PCB layouts should also follow the verified 28-SOIC footprint and provide the decoupling and clock circuitry required by the manufacturer datasheet. This page consolidates verified distributor specifications, sourcing links, family alternatives, and practical selection guidance. It also distinguishes documented device facts from pricing, lifecycle, and pin-level information that was not established by the supplied source data.

RFQ Contact
Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116PEG

Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116PEG is an 8-bit Z8 microcontroller with 2KB (2K x 8) of one-time programmable program memory, 125 bytes of RAM, 24 I/O lines, and a maximum operating frequency of 16MHz in a 28-DIP (0.600-inch, 15.24mm) package. Its specified operating-voltage range is 4.5V to 5.5V. An 8-bit microcontroller is a compact embedded-control IC used to execute firmware, read inputs, and control outputs in dedicated electronic systems. The Z86E3116PEG belongs to the microcontroller hierarchy, combining a Z8 processor core, program memory, RAM, digital I/O, and embedded timing functions. Its one-time-programmable architecture is intended for products where firmware is written during manufacturing and does not need to be updated in the field. Key device characteristics include 16MHz operation, 24 general-purpose I/O lines, 125 bytes of RAM, and programmable OTP options identified in the source data as RC oscillator, EPROM protection, auto latch disable, and permanent settings. Integrated features reported by the Microchip USA product listing include a power-on reset and watchdog timer, providing basic startup supervision and recovery support for embedded control firmware. The device uses a 5V-class supply range of 4.5V to 5.5V. Its 28-DIP package provides through-hole mounting and a 0.600-inch body width, making it appropriate for legacy-style control boards, industrial controllers, appliance controllers, and compact embedded systems assembled with conventional through-hole techniques. Because the available product information does not include the complete datasheet pin map, individual signal assignments cannot be reproduced safely here. Typical application roles include simple sequencing and logic control, switch and relay management, status-indicator control, small industrial equipment interfaces, and dedicated appliance controllers. In each case, firmware stored in the 2KB OTP program memory determines the control behavior, while the 24 I/O lines provide connections to external sensors, switches, and actuators. Designers should account for the 4.5V to 5.5V supply requirement, confirm that the board uses the 28-pin DIP footprint, and validate timing, oscillator, reset, and watchdog behavior against the manufacturer datasheet before production release. The available data identifies the oscillator as internal, but its frequency range and detailed configuration requirements are not stated. This page consolidates verified distributor specifications, current sourcing information, package details, application guidance, and explicit data gaps. It also distinguishes verified facts from unspecified parameters, helping engineers evaluate the Z86E3116PEG without mistaking generic cross-reference tools for evidence of a pin-compatible replacement.

RFQ Contact
Z86E3116PSG - 16MHz 8-Bit Z8 MCU | Zilog
Z86E3116PSG

Z86E3116PSG - 16MHz 8-Bit Z8 MCU | Zilog

The Zilog Z86E3116PSG is an 8-bit Z8 microcontroller operating at 16 MHz, with 2 KB of one-time-programmable program memory, 125 bytes of RAM, and 24 general-purpose I/O pins. The device is packaged in a 28-pin DIP measuring 0.600 inches across the row spacing, or 15.24 mm. An 8-bit microcontroller is a compact embedded processor designed to execute control logic, monitor digital inputs, and operate peripherals using a relatively small instruction set and memory footprint. Within the embedded-control hierarchy, it belongs to the Z8 family of 8-bit microcontrollers and combines a CPU core, nonvolatile OTP program memory, RAM, timers, and general-purpose I/O in one integrated circuit. The Z86E3116PSG provides a 16 MHz operating frequency, a 2K x 8 OTP architecture, and 24 I/O pins. Its on-chip resources include two 8-bit timers, a power-on reset function, and a watchdog timer. OTP memory allows firmware to be programmed once during manufacturing or commissioning, making the device suitable for fixed-control products in which field updates are unnecessary. The Z8 architecture supports economical embedded-control designs while keeping the external component count relatively low. With 24 I/O pins, the device can directly interface with switches, indicators, relays, sensors, and discrete logic. Two timers support periodic tasks, input timing, debouncing, or basic event counting, while the watchdog timer provides a mechanism for recovering from unexpected program flow faults. Typical uses include appliance controls, small industrial controllers, building-control modules, simple sensor interfaces, LED and lighting controllers, and compact embedded products requiring a DIP footprint. The through-hole DIP package is particularly useful for prototypes, low-to-medium-volume products, and assemblies where socketed or manually inserted construction is preferred. Designers should verify each signal's electrical limits, oscillator requirements, programming method, and timing behavior against the manufacturer datasheet. Because OTP memory cannot be erased, firmware validation and manufacturing-programming controls are especially important. The 28-pin DIP footprint also requires adequate board space, connector accessibility, and mechanical clearance around the device. This page combines the Z86E3116PSG's principal memory, timing, I/O, and packaging characteristics with a focused drop-in alternative assessment, practical implementation guidance, and an application-oriented selection framework for compact Z8-based control designs.

RFQ Contact
Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116SEG

Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116SEG is an 8-bit Z8 CISC microcontroller with 2KB of one-time-programmable program memory, 125 bytes of RAM, 24 I/O lines, and a 16MHz maximum operating frequency, supplied in a 28-pin SOIC package. It operates from a 4.5V to 5.5V supply across a -40°C to +105°C temperature range. A microcontroller is a programmable semiconductor that integrates a CPU, memory, digital I/O, and supporting peripherals into one package. The Z86E3116SEG belongs to the Z8 family of 8-bit microcontrollers, a class commonly used for embedded control because it combines a compact instruction set, dedicated I/O, and low-cost single-power-supply operation. Its larger program and data memories distinguish it from basic 8-pin devices while retaining the straightforward architecture suited to appliance controls, interface logic, and compact embedded systems. Key features include 2KB of OTP program memory, 125 bytes of RAM, 24 I/O lines, and operation up to 16MHz. Programmable OTP options listed in the device data include an RC oscillator, EPROM protection, auto latch disable, and permanent disable. The 28-pin SOIC package is also available in tube packaging according to the verified distributor data, supporting conventional through-hole board assembly rather than a compact surface-mount land pattern. The device uses the Z8 CISC architecture and includes an internal oscillator option according to the published specification summary. Its 125-byte RAM supports protocol state, counters, status flags, and short working buffers, while the 2KB OTP program area provides fixed firmware storage after programming. Because OTP memory cannot be electrically rewritten, firmware changes normally require a new programmed device rather than an in-circuit update. Typical uses include temperature controllers, appliance user interfaces, simple motor-control logic, industrial panel controllers, and embedded peripheral interfaces. In these applications, the 24 available I/O lines can distribute digital signals while the 16MHz operating rate supports time-based control routines and serial communication handling. A designer should still budget memory for interrupts, protocol handling, and application logic. The primary design constraint is nonvolatile program flexibility: OTP programming makes Z86E3116SEG appropriate for production builds with stable firmware, while applications requiring field updates may prefer a flash-memory MCU. Board layouts must also respect the 28-pin SOIC footprint and provide the required 4.5V to 5.5V supply, decoupling, programming interface, and exposed I/O routing. This product page consolidates verified distributor specifications, package information, temperature limits, and drop-in comparison data, then adds practical guidance on OTP programming, power-supply design, PCB layout, and selection constraints that are not presented as a complete replacement for the manufacturer datasheet.

RFQ Contact
Z86E3116SSG - 8-Bit 16MHz OTP MCU | Zilog
Z86E3116SSG

Z86E3116SSG - 8-Bit 16MHz OTP MCU | Zilog

The Zilog, Inc. Z86E3116SSG is an 8-bit Z8 microcontroller operating at up to 16 MHz, with 2 KB of one-time-programmable memory in a 28-pin SOIC package. It combines a compact embedded-control architecture with on-chip nonvolatile program storage for designs that do not require frequent firmware updates. The 28-pin surface-mount package provides dedicated I/O capacity while supporting compact control boards, household appliances, and dedicated embedded modules. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Z8 belongs to the microcontroller hierarchy within integrated circuits and embedded processing. The Z86E3116SSG uses one-time-programmable memory, meaning its final firmware is written during manufacturing or production and cannot be rewritten afterward. This is useful for stable products where field updates are unnecessary and security through write protection is desirable. The device's headline characteristics are an 8-bit CPU architecture, a 16 MHz operating frequency, and 2 KB of OTP program memory. Its 28-pin SOIC package is designed for conventional surface-mount assembly and provides a practical upgrade from larger through-hole controllers when board area is constrained. Because the target MPN is identified as a Z8 2K OTP device, it is suited to compact control logic rather than connectivity-heavy or high-memory embedded systems. Program memory size is the principal design boundary. A 2 KB OTP budget supports a compact state machine, supervisory routine, keypad controller, or simple peripheral-control firmware, but it requires disciplined code sizing and limits the amount of application logic, tables, and diagnostics that can be included. The 16 MHz clock provides the timing headroom needed for responsive control loops, scanning, and communication routines, provided the firmware is designed around the limited code storage. Typical applications include appliance control modules, small motor-control boards, illumination controllers, keypads, security accessories, and compact embedded control products. A designer should assign ports according to the datasheet pin description table and reserve the programming and reset-related pins required by the selected Z8 device functions. The 28-pin package also makes it practical to retain through-hole-style prototyping while moving to automated surface-mount production. The primary engineering consideration is validating the complete firmware image before OTP programming. Because OTP cannot be revised after programming, functional testing, boundary-condition checks, and production traceability become especially important. Verify the oscillator, reset behavior, port multiplexing, and any peripheral configuration against the manufacturer datasheet before releasing devices for programming. This page combines manufacturer-oriented device identification, verified distributor specifications, same-family drop-in candidates, and practical design guidance for teams evaluating the Z86E3116SSG as a compact 8-bit control solution.

RFQ Contact
Z86E3312PSG - 8-Bit 12MHz Z8 MCU | Zilog
Z86E3312PSG

Z86E3312PSG - 8-Bit 12MHz Z8 MCU | Zilog

Zilog Z86E3312PSG is an 8-bit Z8 microcontroller operating at 12 MHz with 4 KB of one-time-programmable program memory, 237 bytes of RAM, and 24 general-purpose I/O pins. The device is housed in a 28-pin plastic DIP package and operates from a 4.5 V to 5.5 V supply. Its integrated peripherals include power-on reset, a watchdog timer, and EBI/EMI connectivity, making it suitable for compact embedded control systems, appliance controls, and simple peripheral interfaces. An 8-bit microcontroller is a programmable semiconductor that executes instructions from a defined instruction set while using registers, memory, and dedicated I/O circuitry to control a system. The Z86E3312PSG belongs to the Zilog Z8 family, combining a general-purpose embedded processor with on-chip memory and communication resources in one package. Its one-time-programmable memory allows a finished device to be programmed once for a specific application, which is useful for cost-sensitive controllers where field re-programming is unnecessary. The Z86E3312PSG combines a 12 MHz operating clock with 4 KB of OTP program memory and 237 x 8 bytes of RAM. Its 24 general-purpose I/O pins provide substantial parallel connectivity for switches, indicators, relays, displays, sensors, and external logic. Integrated power-on reset and watchdog-timer functions support dependable startup and recovery after faults. EBI/EMI resources add external bus or interface capability without requiring a separate protocol controller. The 4.5 V to 5.5 V operating range places the device in a classic 5 V embedded-control environment. A 5 V rail allows direct interfacing with many conventional 5 V logic families, although every external signal and supply rail must remain within the limits defined by the manufacturer datasheet. The 12 MHz clock provides the execution rate for control loops, state machines, user-interface scanning, and moderate data-processing tasks rather than high-throughput workloads. Typical uses include appliance and equipment controllers, building-control interfaces, LED and switch management, simple industrial modules, and embedded peripheral controllers. The 24 I/O pins are particularly useful when a design must connect multiple discrete inputs and outputs while retaining external-bus capability. A system can place the MCU between operator controls and actuators while using the watchdog timer to recover from firmware or communication stalls. Design around the DIP-28 footprint and verify all pin assignments from the manufacturer pin-description table before laying out the PCB. Place the device away from heat sources and follow the recommended decoupling arrangement for the 5 V supply. Because OTP memory cannot be rewritten, validate the complete firmware image before programming the production device and maintain a controlled manufacturing process. This product page consolidates the core electrical, memory, interface, lifecycle, and package characteristics of the Z86E3312PSG with practical application guidance. It also distinguishes verified functions from parameters that require confirmation in the manufacturer datasheet, helping engineers evaluate controller selection, PCB reuse, firmware planning, and production provisioning.

RFQ Contact
Z86E3312SSG - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E3312SSG

Z86E3312SSG - 8-Bit 12MHz OTP Microcontroller | Zilog

Zilog Z86E3312SSG is an 8-bit Z8 microcontroller with a 12 MHz clock, 4 KB of one-time-programmable memory organized as 4K x 8, and 24 I/O ports. The device operates from a 4.5 V to 5.5 V supply and is listed as an active part in the Zilog Z86E3312 family. Its combination of OTP program memory, an 8-bit CPU, and a 5 V operating range makes it suitable for embedded control products requiring fixed-program logic and broad I/O access. An 8-bit microcontroller is a compact embedded-processing device that executes firmware from internal program memory and reads inputs through configurable digital ports. The Z86E3312 belongs to the Z8 family, a hierarchy that includes 8-bit microcontrollers, embedded processors, integrated circuits, and semiconductors. Zilog designed this controller for cost-sensitive appliances, access controls, industrial interfaces, and other systems where deterministic digital control is more important than high memory capacity or high-speed computation. The principal device parameters include a 12 MHz maximum clock frequency, 4 KB of OTP program memory, an 8-bit data bus, 24 I/O ports, and a 4.5 V to 5.5 V supply-voltage range. OTP memory allows the application program to be written during manufacturing and prevents subsequent modification, which supports application locking and production traceability. The 24 available I/O lines provide substantial connectivity for switches, sensors, indicators, relays, and communication peripherals. The Z86E3312SSG is identified as part of the Zilog Z8 microcontroller series and uses the SSG ordering code. Distributor records associate the device with the Z86E3312 family and identify its lifecycle as active. Because the detailed package dimensions, pin assignments, interrupt architecture, timer resources, and electrical timing limits are not stated in the cited product records, engineers should use the manufacturer datasheet and its pin-description table before finalizing a PCB layout. Typical uses for this controller include industrial control panels, appliance control boards, security and access-control equipment, programmable logic controllers, and compact instrumentation. In these applications, the 24 I/O ports can distribute control signals across a compact board, while the 12 MHz clock provides sufficient throughput for sequential logic, debouncing, state-machine execution, and periodic interface servicing. OTP programming is particularly appropriate when the finished control logic must remain fixed. The main design consideration is to verify the complete pinout, pin multiplexing, and peripheral assignments against the manufacturer datasheet before PCB routing. Designers should also confirm that every attached signal remains compatible with the 4.5 V to 5.5 V supply range and that firmware timing accounts for the 12 MHz operating limit. A Request a Quote form is available on this page for current commercial availability, lead time, and quantity requirements. This product record combines the exact Z86E3312SSG identity, core electrical and memory characteristics, lifecycle information, practical embedded-control applications, sourcing guidance, and a conservative drop-in assessment. It is designed to help engineers evaluate whether the MCU fits a fixed-program 8-bit design while separating confirmed specifications from details that still require direct manufacturer-document verification.

RFQ Contact
Z86E3412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog
Z86E3412PSG

Z86E3412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog

Zilog, Inc. Z86E3412PSG is an 8-bit CMOS Z8 microcontroller operating at up to 12 MHz, with 16 KB of one-time-programmable program memory in a 28-pin through-hole DIP package. Its operating supply range is 5.00 V to 5.50 V, making it a directly powered embedded-control component for compact legacy-control systems. An MCU, or microcontroller, is a single semiconductor integrating a processor core, program memory, data memory, and peripherals on one die. Within the embedded-control hierarchy, the Z8 family belongs to the broader category of 8-bit microcontrollers and combines a compact instruction set with application-specific peripherals. Its OTP memory makes the device suitable for products where firmware is finalized during manufacturing and field reprogramming is unnecessary. The principal specifications of the Z86E3412PSG are its 8-bit CPU architecture, 12 MHz maximum clock frequency, and 16 KB OTP program memory organized as 16K x 8. The device is identified as a CMOS Z8 microcontroller, while the manufacturer and distributor listings place it in the 28-pin DIP class. These characteristics distinguish it from devices that require external program memory or provide flash-based field updates. The Z86E3412PSG belongs to the Z86E3412 family and is designed for embedded control rather than high-performance computing. OTP program storage gives the manufacturer a defined, permanently programmed firmware path and can support repeatable production across an appliance or controller. The 12 MHz operating rate provides more timing headroom than many low-pin-count 8-bit controllers while retaining the simplicity of a compact MCU architecture. Typical applications include dedicated appliance controllers, small motor-control boards, keypads, sensor-interface modules, and simple sequence controllers. Its 28-pin DIP format is useful for prototypes, repairable assemblies, and through-hole production where a QFP package would be unnecessary. A system designer should verify peripheral assignments, interrupt behavior, and timing requirements against the device's pin description and application information. A critical design consideration is that OTP memory cannot be erased and rewritten in the field. Firmware changes therefore require a new programmed device or a board-level replacement strategy. Decoupling, oscillator layout, I/O drive, and programming should be implemented according to the manufacturer datasheet, especially in electrically noisy motor or relay-control environments. This product page combines the manufacturer device identity with focused design guidance, verified package and memory details, application analysis, and same-family replacement considerations. It is intended to help engineers confirm fit, assess programming constraints, and plan a reliable embedded-control implementation before requesting an order.

RFQ Contact
Z86E3412SEG - 8-Bit 12MHz 16KB OTP MCU | Zilog
Z86E3412SEG

Z86E3412SEG - 8-Bit 12MHz 16KB OTP MCU | Zilog

The Zilog Z86E3412SEG is an 8-bit Z8 microcontroller operating at 12 MHz with 16 KB of one-time-programmable memory in a 28-pin SOIC package. Its operating voltage range is 3.5 V to 5.5 V, making it suitable for embedded control systems that require a compact, nonvolatile program memory and an 8-bit processing architecture. A microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, and peripherals into one device. The Z8 belongs to the broader 8-bit MCU category, where the embedded processor executes firmware to monitor inputs and control outputs. Unlike a general-purpose microprocessor, the Z86E3412SEG is designed for compact embedded-control tasks such as appliance control, simple industrial interfaces, and embedded peripheral control. The Z86E3412SEG's principal specifications include its 8-bit CPU, 12 MHz operating frequency, and 16 KB of OTP memory. The OTP program memory provides a stable, nonvolatile place for firmware because its contents cannot be erased after programming. The device is also listed with 237 bytes of data memory and a 3.5 V to 5.5 V supply range. Its 28-SOIC package supports conventional PCB assembly and is available in a 300 mil body format. The Z8 architecture is intended for straightforward embedded workloads where deterministic control, compact code size, and low component count are more important than high computational throughput. At 12 MHz, the processor is suitable for polling multiple inputs, executing control logic, communicating through serial peripherals, and managing discrete or analog interface functions. Exact peripheral assignments, interrupt behavior, and electrical limits should be checked against the manufacturer documentation before final circuit implementation. Typical uses include household appliance controllers, small motor-control boards, temperature or level monitoring products, programmable interface modules, and compact industrial automation equipment. In these systems, the MCU can execute startup routines, acquire sensor information, update displays or indicators, and operate actuator outputs while keeping the external hardware count low. Designers should begin with the manufacturer's pin-description table when assigning PCB nets and should preserve the device's documented power, ground, reset, clock, and programming connections. Because the MCU is intended for OTP programming, firmware development must account for the non-erasable program memory. Decoupling, oscillator stability, programming access, and unused-pin treatment should follow the device's recommended application circuit and layout guidance. This product page consolidates the exact orderable MPN, core architecture, memory and frequency specifications, package details, sourcing guidance, and engineering considerations. It also distinguishes confirmed orderable information from characteristics that require the manufacturer datasheet, helping engineers plan sourcing and hardware development without confusing this 28-SOIC device with packages or variants that have different pin assignments.

RFQ Contact