Products (21,000+)

TUSB3210PMG4 - 3.3V USB 2.0 8052 MCU | Texas Instruments
TUSB3210PMG4

TUSB3210PMG4 - 3.3V USB 2.0 8052 MCU | Texas Instruments

Texas Instruments TUSB3210PMG4 is an application-specific USB microcontroller with an 8052 core, USB 2.0 interface, 3.3 V supply operation, and integrated EEPROM in a 64-pin LQFP package. It is packaged in a tray for commercial-temperature production systems. An application-specific microcontroller is an embedded processing IC optimized for a defined peripheral function or interface rather than for general application processing. The TUSB3210 belongs to the microcontroller hierarchy, combining an 8052-compatible CPU core with a USB device controller, on-chip program memory, RAM, and EEPROM. This integration allows a USB-to-GPIO or similar peripheral design to enumerate as a full-speed USB device while reducing the number of external components. The principal operating characteristics are a 3.3 V supply, USB 2.0 full-speed connectivity, an 8052 microcontroller core, and a 64-terminal LQFP package. Its 64 terminals provide access to the controller, firmware-programmable I/O, clock, reset, power, and USB functions. The G4 ordering designation corresponds to the commercial-temperature, tray-packaged configuration identified in the Texas Instruments product information. TUSB3210PMG4 integrates USB connectivity with programmable GPIO behavior rather than requiring a conventional USB PHY and external microcontroller as separate components. The EEPROM supports configuration or parameter retention, while the 8052 core executes the device firmware that identifies the peripheral and controls its external interfaces. Because the device is a dedicated USB controller, its principal engineering task is validating the complete pin, firmware, timing, and USB enumeration design before a board is released. Typical applications include USB-to-GPIO adapters, configurable peripheral controllers, data-acquisition front ends, legacy equipment interfaces, and industrial interface modules. The integrated USB controller can also support firmware-based product identification, control, and status reporting over a full-speed USB connection. External transceivers, protection components, crystals, and storage may still be required according to the selected board architecture. Use the manufacturer pin-description table and reference schematic when assigning PCB tracks, especially for USB data, clock, reset, and exposed supply connections. Preserve the specified decoupling arrangement, maintain controlled USB impedance routing, and validate firmware behavior across bus-powered and externally powered operating conditions. This page combines the manufacturer catalog identity, verified package and ordering information, a strict drop-in replacement assessment, and practical implementation guidance. It also distinguishes the electrically and mechanically interchangeable ordering option from devices that only perform a similar USB-interface function but do not share the 64-pin LQFP footprint.

RFQ Contact
UM9830 - Microchip EOL Component | Discontinued Part
UM9830

UM9830 - Microchip EOL Component | Discontinued Part

The Microchip UM9830 is a discontinued component originally manufactured by Microchip Technology, classified by manufacturer product change notice MFOL-19MRQH667 as obsolete effective 2025-06-26 with no further supply and no suggested replacement. According to the referencesource.org EOL mapping entry dated 2026-08-03, the UM9830 belongs to a family of discontinued Microchip parts (alongside UM9369, UM9921, UM7006B, UM9993, UM9301, and UM4306B) that have reached end-of-life status without direct successor parts. Because no functional successor has been specified by the manufacturer, any second-source strategy must be designed at the board level rather than at the part level. This part entered the obsolete category effective immediately on 2025-06-26 and has no last-time-buy window or last-ship date; existing inventory is the only remaining source. A web search for this exact MPN on distributor sites returns generic MicrochipDirect landing pages without parametric content, meaning specific electrical parameters, package information, and qualification data for the UM9830 are not publicly indexed. Engineers requiring the original functionality of this part should treat any remaining stock as sole-source and should plan a board-level redesign rather than pursue a drop-in replacement. Key facts about this listing: the manufacturer is Microchip Technology, the lifecycle status is obsolete as of mid-2025, the product change notice identifier is MFOL-19MRQH667, and no alternate or suggested replacement MPN exists in the public Microchip cross-reference catalog. Procurement teams should treat remaining inventory as legacy stock and validate each lot against the original design specification before assembly. Where this part was used in long-lifecycle programs, distributors carrying remaining stock may be the only legal supply path. This page synthesizes the publicly available lifecycle information, the Microchip product change notice reference, and practical procurement guidance that the manufacturer has not consolidated into a single datasheet. Because the UM9830 has no published parametric specification indexed in the public web (only an EOL notice), the spec table below is intentionally sparse and uses [DATA_NEEDED] markers wherever Microchip's internal documentation would normally supply values. Engineering teams should contact Microchip directly or reference internal design archives for original parameter sets.

RFQ Contact
UPD78F0532AGB-GAH-AX - 8-Bit 20MHz 24KB Flash MCU | Renesas
UPD78F0532AGB-GAH-AX

UPD78F0532AGB-GAH-AX - 8-Bit 20MHz 24KB Flash MCU | Renesas

The Renesas UPD78F0532AGB-GAH-AX is an 8-bit CISC microcontroller from the 78K0/Kx2 family, featuring 24KB (24K x 8) of on-chip Flash program memory and a maximum operating frequency of 20MHz. Housed in a 64-pin LQFP package, the device operates from a 1.8V to 5.5V supply range (5V specified in the automotive-grade part variant) and integrates a rich peripheral set including timers, A/D converter, serial interfaces, and interrupt controllers typical of the 78K0/Kx2 family. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for cost-sensitive, low-power embedded control. Within the broader taxonomy, 8-bit MCUs belong to microcontrollers -> embedded processors -> semiconductor ICs. The 78K0/Kx2 family from Renesas specifically targets compact, low-power general-purpose applications using a CISC (Complex Instruction Set Computer) architecture with an instruction set tuned for code density and deterministic interrupt response, distinguishing it from RISC-based 8-bit families such as 8051 or AVR. Key features include 24KB of Flash memory for application code and data storage, 1KB of on-chip RAM (typical of this family), an integrated 10-bit A/D converter, multiple 16-bit timers, UART and CSI serial interfaces, and a programmable watchdog timer. The device supports both 3V and 5V operation, providing flexibility for battery-powered and industrial systems. The 64-pin LQFP package offers 60+ GPIO pins for interfacing with sensors, displays, and actuators. The 78K0/Kx2 architecture employs a CISC instruction set with variable-length instructions (1-6 bytes) and a hardware multiplier, achieving efficient code density for embedded applications. The integrated Power-On Reset (POR), Low-Voltage Detection (LVD) circuit, and on-chip debug interface simplify system design and reduce external component count. The part is qualified for the automotive operating temperature range (-40C to +85C or -40C to +125C depending on variant), making it suitable for harsh environments. Typical applications include automotive body control modules, HVAC controllers, instrument clusters, industrial sensor interfaces, consumer white goods, and small home appliances. The combination of Flash memory, low power consumption, and the robust 78K0 instruction set makes this MCU well-suited for cost-sensitive motor control and sensor signal processing tasks. When designing with this device, ensure that the on-chip regulator bypass capacitors are placed close to the VDD/VSS pins, and that unused I/O pins are configured as outputs or pulled to defined logic levels to minimize power consumption. The Flash memory write/erase cycles require a minimum operating voltage of 2.7V; for battery-backed designs, plan for brown-out detection. This page synthesizes distributor availability, drop-in alternatives from the 78K0/Kx2 family, and practical design notes not found on standard distributor listings.

RFQ Contact
USB2005-MN-01 USB 2.0 ATA/ATAPI Controller | Microchip
USB2005-MN-01

USB2005-MN-01 USB 2.0 ATA/ATAPI Controller | Microchip

The Microchip Technology USB2005-MN-01 is an application-specific USB 2.0 ATA/ATAPI controller used to bridge a Universal Serial Bus host interface with an IDE storage device. The verified distributor records identify the device as a microcontroller-class integrated circuit associated originally with SMSC and list it for electronic procurement and reference. Its defining functional parameters are USB 2.0 host connectivity and ATA/ATAPI device support; no complete manufacturer electrical table was included in the supplied data, so details such as transfer rate, supply voltage, clock frequency, and pin assignments remain unverified. An application-specific controller is a specialized semiconductor that integrates the logic required for a particular external interface or system function. In the USB 2.0 ATA/ATAPI category, this device belongs to the broader hierarchy of controller IC, interface IC, embedded controller, and semiconductor. Its role is more specialized than a general-purpose microcontroller because the controller is designed around the command, signaling, and data-path requirements of connecting USB storage equipment to an ATA/ATAPI bus. The primary verified feature is support for the USB 2.0 and ATA/ATAPI standards. A USB 2.0 host interface can use this controller when a system needs to operate compatible ATA storage through a USB connection rather than a conventional internal IDE interface. The listing also classifies USB2005-MN-01 as an application-specific microcontroller, distinguishing it from generic logic, memory, and power-management components. Its USB-to-storage positioning makes it relevant to legacy storage adapters, embedded systems, and equipment requiring an operating-system-visible USB mass-storage path. Engineering use requires careful verification before schematic capture. The supplied records do not provide the exact package designation, exposed-pad requirements, pinout, clocking method, regulator architecture, or power-consumption limits. They also do not establish whether the device supports SATA, external power, hot-plug handling, bus-powered media, or particular USB suspend and wake behaviors. Those capabilities must be confirmed from the complete manufacturer datasheet and errata before USB signal routing, storage-interface timing, or PCB layout is finalized. Typical applications include USB-to-ATA storage adapters, embedded data-logging equipment, industrial controllers with legacy disk storage, service and test systems for older IDE devices, and computer peripherals that retain ATA/ATAPI connectors. The device should be evaluated where a host must communicate with a compatible ATA/ATAPI target through USB 2.0 while preserving the established command set and storage-device behavior. The primary design caution is that a USB 2.0 label alone does not establish present-day performance or compatibility. Engineers should verify supported USB speed modes, maximum transfer rate, enumeration behavior, ATA timing, cable length, and media-power requirements. Board design should also reserve space for the verified package, decoupling network, USB data routing, ATA signal conditioning, and any required external storage power. This page consolidates verified distributor pricing, a function-oriented technical summary, procurement guidance, comparison limits, and practical design cautions. It distinguishes confirmed USB 2.0 ATA/ATAPI functionality from unverified electrical details so engineers can assess suitability without mistaking catalog summaries for a complete datasheet specification.

RFQ Contact
USB2228AHZS07 USB 2.0 Flash Media Controller | SMSC
USB2228AHZS07

USB2228AHZS07 USB 2.0 Flash Media Controller | SMSC

The SMSC USB2228AHZS07 is an application-specific microcontroller configured as a fourth-generation USB 2.0 flash media controller with an integrated card interface. It is identified in the 26-page USB2228 datasheet and is supplied in an unspecified surface-mount package. Its core role is to provide a USB host-facing storage interface for flash-memory cards, combining USB connectivity, media-card control, and configuration logic in one integrated circuit. An application-specific microcontroller is a specialized semiconductor optimized for a defined set of system functions rather than general-purpose software execution. Within the product hierarchy, this device belongs to the microcontroller and embedded-controller class, while its specific application places it in the flash media controller category. This integration can reduce the number of discrete components required between a USB port and a removable flash card. The fourth-generation controller architecture identifies the USB2228 family as a dedicated USB 2.0 storage solution. USB 2.0 provides a standardized host-to-controller interface, while the integrated card functionality manages communication with supported removable flash media. The part is specifically listed by Rochester Electronics as an application-specific microcontroller from SMSC, and market listings associate the device with a 26-page manufacturer datasheet. Designing with this controller requires attention to the USB host interface, card electrical requirements, supported media formats, embedded firmware, and the exact package dimensions. Because the device is application-specific, its operational behavior is typically determined by its internal firmware and board configuration rather than by a general-purpose processor application. Designers should preserve the reference network, clocking arrangement, power sequencing, and card-detection implementation used by the manufacturer. Typical uses include USB flash-card readers, card-reader appliances, portable storage accessories, embedded storage gateways, and host systems that require direct access to removable flash media. In each case, the controller handles the USB-to-card interface while the surrounding circuit supplies regulated power, termination, protection, and the physical media connector. The principal design trade-off is integration versus upgrade flexibility. A dedicated flash media controller can simplify the USB storage path, but it is less versatile than a general-purpose microcontroller. Validate the supported card types, transfer modes, firmware configuration, package land pattern, and signal-routing requirements before releasing a new PCB layout. This product record combines the exact USB2228AHZS07 identification, manufacturer description, package-related uncertainty, verified source links, and application-oriented engineering guidance. It also separates confirmed attributes from parameters that require confirmation against the manufacturer datasheet, helping engineers plan sourcing and hardware review without obscuring unresolved design assumptions.

RFQ Contact
W55RP20 - RP2040+W5500 Ethernet SiP MCU | WIZnet
W55RP20

W55RP20 - RP2040+W5500 Ethernet SiP MCU | WIZnet

The WIZnet W55RP20 is a System-in-Package (SiP) ioMCU that integrates the Raspberry Pi RP2040 dual-core Arm Cortex-M0+ microcontroller running at 133 MHz with the W5500 hardware TCP/IP Ethernet controller, in a 68-pin VFQFN exposed-pad package. It combines 2 MByte of on-chip flash memory and 264 kB of on-chip SRAM organized in six independent banks with a full hardwired TCP/IP stack and a 12-channel DMA controller. A System-in-Package device stacks or side-by-side mounts two dies within a single molded package, so the W55RP20 functions electrically as one microcontroller with built-in Ethernet, eliminating the two-chip RP2040-plus-W5500 solution that previously required separate routing, crystals, and power domains. In the product hierarchy it sits as: ioMCU -> communications controller microcontroller -> Ethernet microcontroller -> IoT connectivity IC. Key features include the dual Cortex-M0+ cores at 133 MHz, 2 MB flash for code storage, 264 kB SRAM in six independent banks, and the W5500 subsystem with a hardwired TCP/IP stack supporting 8 hardware sockets, which offloads protocol processing entirely from the CPU. A 12-channel DMA controller supports memory-to-peripheral, peripheral-to-memory, and memory-to-memory transfers, each channel with its own control and status registers, letting the processor switch to other tasks or low-power states during large data transfers. The W5500 die provides a hardware TCP/IP stack implementing MAC and PHY functionality for 10/100 Mbps Ethernet, so networking is deterministic and does not consume MCU cycles for protocol handling. This architecture suits applications where wire-speed throughput and low jitter matter more than a large software network stack. Typical applications include industrial IoT gateways, networked sensor nodes, smart-building controllers, and Ethernet-enabled embedded systems where developers want Raspberry Pi Pico-class processing plus native wired networking in one chip. Design consideration: as a SiP, thermal dissipation is combined from both dies; verify total power budget and provide adequate ground-plane copper under the exposed pad for heat spreading and signal return. This page synthesizes distributor pricing, availability, evaluation-board references, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
W55RP20-S2E - Serial-to-Ethernet MCU, 2MB Flash | WIZnet
W55RP20-S2E

W55RP20-S2E - Serial-to-Ethernet MCU, 2MB Flash | WIZnet

The WIZnet W55RP20-S2E is a pre-programmed serial-to-Ethernet communications controller microcontroller IC built on the W55RP20 System-in-Package, delivering a dual ARM Cortex-M0+ core at 133 MHz, 2MB on-chip Flash, and a hardwired 10/100 Mbps Ethernet TCP/IP controller in a 68-pin VFQFN package with exposed pad. Each unit ships with WIZnet serial-to-Ethernet (S2E) firmware and a unique MAC address from the WIZnet OUI block. An application-specific communications microcontroller, or ioMCU, is a device that combines a general-purpose MCU core with dedicated network hardware. In the W55RP20-S2E, the integration hierarchy runs: serial-to-Ethernet chip -> communications controller MCU -> Ethernet IC -> power/networking semiconductor. Unlike software TCP/IP stacks that consume MCU cycles, the integrated W5500-style hardwired TCP/IP core offloads protocol processing in silicon. Key features include the SiP integration of Raspberry Pi's RP2040 microcontroller and WIZnet's W5500 Ethernet controller, 264kB on-chip SRAM organized in six independent banks, a 12-channel DMA controller supporting memory-to-peripheral, peripheral-to-memory, and memory-to-memory transfers, and a USB 2.0 full-speed (12 Mbps) controller usable as host or device. The serial-to-Ethernet firmware supports serial speeds up to 921,600 bps, letting any UART-equipped device gain Ethernet connectivity without protocol development. The dual Cortex-M0+ architecture lets one core handle application logic while the other manages network I/O, and the hardwired TCP/IP stack supports 8 independent sockets with minimal latency. Because the TCP/IP, MAC, and PHY functions are hardened in silicon, software stack bugs and CPU load from protocol handling are essentially eliminated. Typical applications include adding Ethernet to legacy industrial equipment with UART ports, IoT smart-device connectivity, and networked sensor or control nodes. The pre-programmed firmware approach removes firmware certification and development risk for serial-to-Ethernet designs. Design consideration: since this is a pre-programmed part, use the bare W55RP20 if custom firmware is required; the S2E variant is optimized for UART-to-Ethernet bridging with minimal development effort. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
W681308DG - USB Audio Controller 16-bit 48-LQFP | Nuvoton
W681308DG

W681308DG - USB Audio Controller 16-bit 48-LQFP | Nuvoton

The Nuvoton W681308DG is a USB audio controller IC with an integrated 16-bit audio codec, housed in a 48-pin LQFP (7x7 mm) surface-mount package. As a member of the Winbond/Nuvoton W6813 series of USB audio controllers, it integrates a USB controller, audio codec, and embedded microcontroller into a single chip for USB audio peripheral designs. A USB audio controller is a mixed-signal device that implements the USB audio class protocol on the digital side and an audio codec (codec = coder-decoder) on the analog side. Within the system hierarchy, it sits between a general-purpose USB microcontroller and a dedicated audio codec: it handles USB enumeration, audio streaming, clocking, and sample-rate conversion, while also providing microphone and speaker signal paths. This integration reduces bill-of-materials count compared to a discrete USB MCU plus external codec solution. Key features of the W681308DG include a 16-bit audio data path, USB full-speed audio transport, integrated microphone and speaker audio channels, and a compact 7x7 mm 48-LQFP footprint that supports consumer peripheral form factors. The device operates from a 3.3 V supply, consistent with the family datasheet description of the W681308 series as a 3.3 V part. Architecturally, the W681308 combines an 8-bit CISC microcontroller core with on-chip program memory and a hardwired USB audio function block. The codec front end handles anti-aliasing filtering, ADC for microphone inputs, and DAC for speaker outputs, while the MCU firmware manages HID interfaces, mute/volume controls, and other USB descriptor behavior. Refer to the manufacturer datasheet for precise clock, PLL, and interface specifications. Typical applications include USB headset and headphone amplifiers, desktop microphone arrays, USB speakerphones, VoIP handsets, and general USB audio dongles where a single-chip, low-cost USB audio solution is required. A key design consideration is analog layout: the microphone preamp and DAC outputs are sensitive to digital return-path noise, so a solid ground plane, careful separation of analog and digital traces, and proper decoupling of the 3.3 V rail per the manufacturer datasheet recommendations are essential for a low-noise result. This page synthesizes distributor sourcing data, datasheet references, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
W77C032A40FL - 40MHz 8-Bit ROMless MCU | Nuvoton
W77C032A40FL

W77C032A40FL - 40MHz 8-Bit ROMless MCU | Nuvoton

The Nuvoton W77C032A40FL is a ROMless Turbo-51 8-bit microcontroller operating at up to 40 MHz, with 1K x 8 bits of RAM, 36 I/O pins, and a 44-pin BQFP package. Designed for embedded control applications, the device combines a high-clock-speed 8051-compatible core with an internal oscillator, allowing designers to build compact control systems without adding an external program-memory device. An 8-bit microcontroller is a semiconductor integrated circuit containing a central processing unit, memory, I/O ports, and peripheral functions on one package. In the product hierarchy, it belongs to the microcontroller family of embedded processors and embedded ICs. The W77C032A40FL belongs to the Turbo-51 family and uses a ROMless architecture, meaning program storage must be supplied by external memory while working data can be held in its internal RAM. Key characteristics include a maximum clock frequency of 40 MHz, 1K x 8-bit SRAM, and 36 general-purpose I/O lines. Its internal oscillator reduces the external clock-component count, while the 44-BQFP package exposes substantially more I/O than smaller dual-inline or small-outline packages. These characteristics make the MCU appropriate for compact controllers with multiple discrete inputs and outputs, particularly where an 8051-compatible instruction set and external program memory are required. The W77C032A40FL is positioned as a ROMless Turbo-51 device rather than a self-contained MCU with embedded Flash. External program memory and interface circuitry therefore influence the complete memory system. Its 36 I/O pins provide ample connectivity for control signals, indicators, relays, sensors, and communication peripherals. Because the device is specified at 40 MHz, firmware timing, memory-access delays, peripheral clock requirements, and external-memory interface timing must be reviewed together during schematic and PCB design. Typical applications include industrial machine controls, building-control modules, appliance controllers, interface modules, and other embedded automation products. The combination of 36 I/O, internal RAM, and external program-memory support is especially useful when a product needs substantial I/O breadth but limited on-chip volatile memory. The MCU can act as the supervisory controller between sensors, actuators, communications circuitry, and discrete logic. A key design consideration is that ROMless operation requires careful implementation of the external memory interface and correct timing for the selected memory device. Place decoupling close to the supply pins, route oscillator and memory signals consistently, and keep high-current switching nodes away from sensitive control inputs. Confirm pin multiplexing, reset behavior, and peripheral availability against the manufacturer datasheet before finalizing firmware and board connections. This page consolidates the principal electrical, memory, package, sourcing, and replacement information for W77C032A40FL. It also provides practical application guidance and design checks that help engineers determine whether this ROMless Turbo-51 MCU fits a control design before committing to PCB layout and external-memory implementation.

RFQ Contact
W77C032A40PL - 40MHz ROMless 8051 MCU | Nuvoton
W77C032A40PL

W77C032A40PL - 40MHz ROMless 8051 MCU | Nuvoton

The Nuvoton Technology Corporation W77C032A40PL is an 8-bit ROMless 8051-compatible microcontroller operating at up to 40 MHz, with 1 KB x 8 RAM, 36 I/O lines, and a 44-pin PLCC package. The device uses the W77C032 Turbo-51 processor architecture, which reduces wasted instruction cycles and executes 8051 instructions approximately 1.5 to 3 times faster than a traditional 8051 core at the same clock speed. A microcontroller is a programmable semiconductor integrating a processor core, memory, I/O ports, timers, serial communications, and interrupt functions on one integrated circuit. The W77C032 belongs to the 8-bit MCU hierarchy and retains 8052 pin and instruction-set compatibility. Because the part is ROMless, application firmware must be supplied through external program-memory hardware, making the device suitable for systems that require flexible code storage, boot loading, field updating, or shared memory among several devices. The principal specifications include a 40 MHz maximum operating speed, 1 KB x 8 internal RAM, four 8-bit I/O ports, 36 total I/O lines, and an internal oscillator. The W77C032 also incorporates standard 8052 resources, including three 16-bit timer/counters, a full-duplex serial port, and multiple interrupt sources. Its 4.5 V to 5.5 V operating range and 44-PLCC package support established 5 V embedded-control architectures where a leaded, socket-compatible footprint is preferable to a fine-pitch surface-mount package. The redesigned processor core avoids wasted clock and memory cycles, improving execution efficiency without changing the familiar 8051 instruction set. This combination is useful when maintaining legacy 8051 source code while increasing control-loop or peripheral-handling performance. Since the MCU has no on-chip program memory, a system designer must account for external ROM or another memory source when creating the memory map, boot sequence, and firmware-loading architecture. Typical uses include industrial controllers, embedded data-acquisition equipment, communications controllers, legacy 8051 peripheral upgrades, and compact automation modules. The 36 I/O lines provide substantial parallel-interface capacity, while the timers and serial port reduce the need for external peripheral chips. Board-level designs should also provide a stable clock or oscillator arrangement, external program-memory interfacing, suitable decoupling, and adequate pin-compatible routing. A key design consideration is that the PLCC package has 44 positions, but the verified product records do not provide a complete numbered pin description. Engineers should therefore assign the PCB footprint and nets directly from the pin table and package drawing in the manufacturer data sheet rather than inferring connections from generic 8051 diagrams. Confirm the external-memory interface, reset behavior, clock requirements, and available I/O before finalizing the board layout. This product summary consolidates the confirmed architecture, memory, clock, package, sourcing, and lifecycle information with engineering guidance for external-memory implementation, firmware compatibility, and PLCC layout. It also distinguishes directly documented characteristics from parameters that still require confirmation from the complete manufacturer data sheet.

RFQ Contact
W77E058A40FL - 40MHz 8051 32KB Flash MCU | Nuvoton
W77E058A40FL

W77E058A40FL - 40MHz 8051 32KB Flash MCU | Nuvoton

Nuvoton Technology Corporation W77E058A40FL is an 8-bit CMOS W77-series microcontroller with 32 KB of embedded Flash memory, a 40 MHz operating frequency, and a 44-BQFP package. It uses a four-clock machine-cycle 8051-compatible architecture and operates from a 5 V supply, combining legacy MCS-51 software compatibility with substantially faster instruction execution than the original standard 80C51 family. An 8051-compatible microcontroller is an embedded processor designed around the MCS-51 instruction set and its associated register, interrupt, timer, serial-interface, and port architecture. The W77 series places that established software ecosystem within the broader hierarchy of embedded controllers, 8-bit microcontrollers, and general-purpose semiconductor devices. This makes it useful for control systems that benefit from established 8051 tools and code while requiring higher processing throughput and integrated Flash rather than an external program-memory device. The W77E058A40FL combines several headline characteristics: 8-bit processing, 40 MHz operation, and 32 KB of embedded Flash. Its four-clock machine-cycle design executes each machine cycle in a quarter of a full 40 MHz clock period. The device also provides four 8-bit I/O ports and follows the MCS-51 instruction set, allowing engineers to reuse familiar driver concepts and peripheral-control code while selecting a faster Flash-based implementation. Technically, the part belongs to the W77 family and is positioned as a compact, 5 V embedded controller. Its Flash memory consolidates program storage on the die, simplifying the hardware arrangement compared with an architecture that requires external program memory. Because the controller remains compatible with the MCS-51 instruction set, software migration from an appropriate 80C52-class design can be easier than moving to a different instruction set. Board compatibility still requires verification of pin functions, electrical limits, memory organization, and peripheral availability. Typical applications include industrial keypad and panel controllers, motor and relay-sequencing modules, compact instrumentation, appliance-control boards, and legacy 8051 peripheral upgrades. The 40 MHz execution rate can improve responsiveness in polling loops, protocol handling, and time-dependent control tasks, while the four 8-bit I/O ports support digital input, output, and external-interface connections when the remaining pins provide the required clock, reset, and power functions. A key design consideration is that pin-compatible software does not automatically prove drop-in electrical compatibility. Before replacing an existing 8051 device, verify the 44-BQFP footprint, pin assignments, reset behavior, operating voltage, oscillator connections, I/O drive limits, and peripheral functions against the current datasheet. Programming and development-tool requirements should also be checked because instruction-set compatibility does not guarantee that every legacy programmer supports the device. This product page combines the W77E058A40FL's core specifications, verified component listings, application guidance, design checks, and a transparent comparison of candidate cross-reference devices. It also distinguishes confirmed drop-in options from merely similar controllers, helping engineers make a replacement decision without relying on package similarity alone.

RFQ Contact
W77E058A40PL - 40MHz 8051 MCU, 32KB Flash | Nuvoton
W77E058A40PL

W77E058A40PL - 40MHz 8051 MCU, 32KB Flash | Nuvoton

Nuvoton Technology Corporation W77E058A40PL is an 8-bit CMOS 8051-compatible microcontroller operating at up to 40 MHz, with 32KB of Flash memory in a 44-pin PLCC package. It executes four clocks per machine cycle, provides two UART devices and two DPTR registers, and operates from a 5 V supply across the 4.5 V to 5.5 V range. The W77E058A family is also pin-compatible with traditional 12T 8051 devices. An 8051 microcontroller is an embedded-computing IC that combines a CPU core, program memory, data memory, I/O ports, and peripherals on one integrated circuit. Within the product hierarchy, the W77E058A is an 8-bit MCU, a 4T 8051 MCU, a member of the MCS-51 instruction-set family, and a member of the broader embedded processor and semiconductor categories. Its 8051 compatibility supports established compiler, debugger, and application-development ecosystems. Key features include a 40 MHz maximum operating frequency, a four-clock machine-cycle architecture, and 32KB of on-chip Flash organized as 32K by 8 bits. Two UART devices support serial communication, while two DPTR registers provide separate 16-bit pointer contexts. Four 8-bit I/O ports support digital interfaces, and the 4.5 V to 5.5 V operating range aligns the device with conventional 5 V embedded equipment. The device uses an 8-bit CISC architecture compatible with the MCS-51 instruction set and remains compatible with traditional 12T 8051 interfaces. Its 4T architecture reduces the clock-to-machine-cycle ratio to four clocks, allowing 40 MHz operation without changing the fundamental software timing model. Because the product is identified as NRND, engineers should verify availability and consider the manufacturer's current portfolio before starting a new design. Typical applications include security and alarm systems, communication equipment, industrial control, power-management controllers, and industrial personal computers. The two UARTs are useful for sensor, transceiver, display, or host serial links, while the four parallel I/O ports can handle digital control signals, status indicators, relay logic, or keypad interfaces. The principal design consideration is the 5 V supply requirement and the limited 0°C to 70°C temperature range. Decoupling and signal-integrity practices remain important because all peripherals share the same supply and ground system. Engineers should also confirm the PLCC-44 footprint, pin assignments, and board-level clearances against the manufacturer datasheet before layout release. This page combines the manufacturer's family-level architecture and lifecycle information with distributor specifications and a practical replacement assessment. It also identifies the package, programming interface considerations, application fit, and design checks needed to evaluate the W77E058A40PL in an embedded control platform.

RFQ Contact
W77E516A40FL - 40MHz 8051 MCU 64KB Flash | Nuvoton
W77E516A40FL

W77E516A40FL - 40MHz 8051 MCU 64KB Flash | Nuvoton

Nuvoton Technology Corporation W77E516A40FL is an 8-bit 8051-compatible microcontroller operating at 40 MHz with 64 KB of embedded Flash program memory in a 44-pin PQFP package. The device includes four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex serial port, and interrupt resources inherited from the standard 8052 architecture. Its redesigned processor core removes wasted clock and memory cycles, allowing typical instructions to execute approximately 1.5 to 3 times faster than a traditional 8051 at the same crystal frequency. An 8051-compatible microcontroller is an embedded control processor that retains the classic 8051 instruction set while adding a redesigned execution core and modern integrated Flash memory. The W77E516 belongs to the 8-bit microcontroller hierarchy, where Flash program memory replaces externally attached ROM and supports compact, self-contained control systems. This combination makes the device suitable for industrial controllers, communication equipment, data-acquisition modules, and legacy equipment upgrades where existing 8051 software can be retained. The principal specifications are a 40 MHz operating speed, 64 KB of 64K x 8 Flash program memory, 1 KB of 8-bit RAM, 36 I/O lines, and a 5 V supply. Its 8052-compatible architecture provides four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex UART, and multiple interrupt sources. The redesigned core improves instruction throughput without requiring a change to the standard 8051 instruction set, which helps designers reuse established firmware and peripheral-driver routines. Program execution benefits from a processor architecture that avoids wasted memory and clock cycles. Because the device is instruction-set compatible with the 8052, software can use standard 8051 development tools while taking advantage of the faster core. The integrated Flash memory consolidates program storage onto the device, reducing system-level component count and allowing firmware updates to be handled without a separate external memory device. Typical applications include industrial control panels, serial-interface adapters, test and measurement instruments, embedded data collectors, and communication modules. The 36 available I/O lines support peripheral connections, while the timer/counter and serial resources reduce the need for external interface components. The device is also appropriate for maintaining older 8051-based products where software compatibility is more valuable than migration to a different instruction set. The main design consideration is that the W77E516A40FL is an 8-bit, 5 V device rather than a low-power 3.3 V or modern 32-bit controller. Board designs should provide the specified 5 V operating supply, correct decoupling, and a stable clock source. Verify oscillator requirements, absolute maximum ratings, and timing margins in the manufacturer datasheet before laying out a new PCB, especially when replacing an electrically different original MCU. This page combines the manufacturer technical description, distributor specifications, packaging information, and practical guidance for evaluating the W77E516A40FL in 8051-compatible designs. It also identifies the scarcity of verified pin-compatible substitutes, providing a drop-in cross-reference candidate without presenting unverified components as equivalent parts.

RFQ Contact
W77E532A40PL - 40MHz 8051 128KB Flash MCU | Nuvoton
W77E532A40PL

W77E532A40PL - 40MHz 8051 128KB Flash MCU | Nuvoton

The Nuvoton Technology Corporation W77E532A40PL is a 40 MHz, 8-bit 8051-compatible microcontroller with 128KB of program Flash, 1KB of RAM, 36 general-purpose I/O pins, and a 44-pin PLCC package. It operates from a single 5 V supply and executes the standard 8051 instruction set in a four-cycle architecture. An 8051-compatible microcontroller is an embedded controller that retains the classic 8051 programming model and peripheral structure while using an internally redesigned processor core. The W77E532A belongs to the W77 family of enhanced 8051 devices, providing compatibility with 8052 software and the hardware resources expected from a standard 8052, including four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex serial port, and interrupt sources. Key device characteristics include a 40 MHz operating speed, 128KB of Flash program memory, 1KB of internal RAM, and 36 I/O pins. The redesigned core removes wasted clock and memory cycles, allowing instructions to complete approximately 1.5 to 3 times faster than a traditional 8051 at the same crystal frequency. A 5 V supply and 44-pin J-lead PLCC package make the device suitable for established embedded control platforms rather than new high-density mixed-signal designs. The W77E532A architecture remains instruction-set and 8052 pin compatible while improving execution efficiency. Its 128KB Flash area provides substantially more program storage than many classical 8051 controllers, reducing the need for external program memory in larger control routines. Integrated timers support periodic timing, event counting, and modulation tasks, while the serial port handles low-speed communication with external controllers or data acquisition modules. Typical uses include industrial controllers, data acquisition equipment, communications interfaces, embedded instrumentation, and legacy 8051 system upgrades. The device can also serve as a bridge between an established 8051 software base and a newer PCB revision, provided the board footprint, supply rail, oscillator arrangement, and peripheral assignments match the original controller. When designing around the W77E532A40PL, confirm the 5 V supply tolerance, external crystal or clock connection, Flash programming method, and reset configuration against the manufacturer datasheet. Because the PLCC package is legacy-oriented, it is less convenient than an LQFP or QFP package for automated assembly, hand soldering, or compact consumer products. This page consolidates device specifications, package information, application guidance, and verified same-footprint alternatives into a practical engineering reference. It also highlights where an engineer must confirm pin mapping, timing, and supply requirements before treating a candidate as a functional replacement.

RFQ Contact
W77I058A25PL - 8-Bit 25MHz 32KB Flash MCU | Nuvoton
W77I058A25PL

W77I058A25PL - 8-Bit 25MHz 32KB Flash MCU | Nuvoton

The Nuvoton Technology Corporation W77I058A25PL is an 8-bit W77-series 8051-compatible microcontroller operating at up to 25 MHz, with 32 KB of flash program memory and a 44-pin PLCC package. It operates from 2.7 V to 5.5 V and is specified for temperatures from -40 °C to +85 °C. The device combines a four-cycle 80C51-class core with 1 KB of internal RAM and 36 I/O lines for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, I/O ports, and peripheral functions onto one device. The 8051-compatible instruction set belongs to the broader 8-bit embedded-controller family. Nuvoton's W77 series targets applications in which deterministic 8-bit control, integrated flash memory, and a broad operating-voltage range are more useful than the compute density or peripheral breadth of a 32-bit processor. The W77I058A25PL provides 32 KB of flash memory organized as 32K x 8, allowing firmware and constant data to be stored on the chip. Its internal data memory is 1K x 8 bytes, and 36 I/O pins provide connections for sensors, switches, displays, actuators, and communication interfaces. The four-cycle 80C51 execution architecture supports clock speeds up to 25 MHz while retaining a familiar programming model. Operation from 2.7 V to 5.5 V makes the device suitable for both 3.3 V and 5 V system environments. The specified -40 °C to +85 °C industrial temperature range supports equipment operating across extended ambient conditions. Its PLCC-44 package also offers a leaded mechanical format useful for through-hole assembly, repair, and designs where connectorized or socketed parts are preferred. Typical uses include industrial control panels, communications equipment, connected peripherals, printer controllers, automotive infotainment interfaces, and fixed-line access products. At 36 I/O, the controller can supervise multiple discrete inputs and outputs while retaining flash-based programmability for product variants and field updates. When designing the board, verify the oscillator and reset implementation against the manufacturer datasheet, reserve all required power pins, and route the 36 I/O signals according to the PLCC-44 pin description. Because PLCC parts can be socketed, confirm solderability and assembly-process requirements early in the mechanical design. This page consolidates the confirmed controller specifications, package details, sourcing information, application guidance, and design considerations into one engineering reference for evaluating the W77I058A25PL in new or existing 8051-compatible equipment.

RFQ Contact
W77IC32A25PL - 25MHz ROMless 8051 MCU | Nuvoton
W77IC32A25PL

W77IC32A25PL - 25MHz ROMless 8051 MCU | Nuvoton

Nuvoton Technology Corporation W77IC32A25PL is an 8-bit ROMless W77 Turbo-51 microcontroller operating at 25 MHz, with 1K x 8 RAM, 36 I/O lines, and a 44-pin PLCC package. It is intended for embedded 8051-compatible control systems that require an external program-memory device while retaining a conventional 8-bit MCU architecture. A ROMless 8051 microcontroller is a variation of the MCS-51 microcontroller family in which the program memory is not integrated on the chip. The processor executes its firmware from external memory, allowing application-specific code capacity to be selected during system design. Within the semiconductor hierarchy, W77IC32A25PL belongs to the 8-bit microcontroller class, the broader embedded-processing category, and ultimately the microcontroller and semiconductor ecosystems. The device combines a 25 MHz clock with a 1K x 8 internal RAM array and 36 input/output lines. Its ROMless architecture is useful when firmware must exceed internal program-memory limits, when multiple products share the same external-memory configuration, or when code updates are managed outside the MCU. The -40°C to +85°C operating-temperature range supports industrial-temperature equipment while retaining compatibility with the established 8051 instruction set and peripheral environment. Technically, the W77 family is positioned as a Turbo-51 implementation, meaning that its clock rate is higher than that of the original 12 MHz 8051 class. At 25 MHz, the device offers greater instruction throughput than standard 8051 parts, although actual application performance depends on bus timing, wait states, external-memory access, and the selected memory architecture. The ROMless design makes external address decoding and code-memory interfacing central parts of the hardware design rather than optional functions. Typical uses include industrial controllers, appliance interfaces, embedded data-acquisition equipment, legacy 8051 peripheral boards, and control modules upgraded from slower standard 8051 processors. The broad I/O count allows the MCU to connect switches, displays, relays, sensors, and communication interfaces while the external program-memory bus accommodates larger firmware images. Designers should also account for the external memory interface timing when calculating system-level operating margins. PCB implementation requires a 44-pin PLCC land pattern, careful routing of the external program-memory bus, and decoupling close to the supply pins. Because the PLCC package is not represented by a dedicated diagram key in the XAIPART package library, use the manufacturer package drawing and pin-description table when assigning tracks. Confirm oscillator, reset, I/O, and memory-bus requirements against the manufacturer datasheet before releasing a layout. This product page combines the verified device identity, package and timing information, application guidance, drop-in comparison limits, and practical implementation cautions. It helps engineers determine whether the W77IC32A25PL fits a new 8051 design or whether an existing board requires qualified substitution and software validation.

RFQ Contact
W77L032A25FL - 25MHz ROMless 8051 MCU | Nuvoton
W77L032A25FL

W77L032A25FL - 25MHz ROMless 8051 MCU | Nuvoton

Nuvoton Technology Corporation W77L032A25FL is an 8-bit ROMless 8051-compatible microcontroller operating at up to 25 MHz, with 1K x 8 RAM, 36 I/O lines, and a 44-BQFP package. It operates from 2.7 V to 5.5 V and uses an internal oscillator. The W77L032 core is designed to complete 8051 instructions faster than a traditional 8051 operating at the same clock speed. An 8051-compatible microcontroller is an embedded processor that implements the widely used MCS-51 instruction set and associated peripheral architecture. Within the embedded-control hierarchy, it belongs to the 8-bit MCU family and provides a simple alternative to larger 16-bit or 32-bit controllers when control logic, serial communications, timers, and limited data processing are the primary requirements. A ROMless device requires an external program-memory interface. Key characteristics include a 25 MHz maximum operating frequency, 1K x 8 bytes of internal RAM, 36 general-purpose I/O pins, and a 2.7 V to 5.5 V supply range. The device is intended for surface-mount assembly in a 44-BQFP package. Its ROMless architecture makes it useful when the application requires external program storage, configuration flexibility, or a larger memory arrangement than an on-chip ROM device provides. The W77L032 core is designed to reduce wasted instruction cycles relative to a conventional 8051 implementation. According to the manufacturer documentation, typical instruction execution can be approximately 1.5 to 3 times faster than a traditional 8051 at the same crystal frequency, depending on the instruction type. This improvement can shorten control-loop execution time without changing the software's 8051 instruction-level compatibility. Typical uses include industrial control panels, compact automation equipment, appliance controllers, serial-interface equipment, and embedded products that already use 8051-compatible code or peripherals. Designers should also consider the external program-memory interface and required memory type when laying out the PCB. For industrial and automotive contexts, verify qualification and operating-temperature requirements before committing the device to a production design. A key implementation consideration is that the external clock, reset, memory, and decoupling connections must follow the pin-assignment and electrical requirements in the W77L032/W77L032A/W77M032A datasheet. Confirm the external memory interface, reset behavior, and I/O allocation in the final schematic rather than deriving them from the package outline alone. This product page consolidates the verified device identity, core specifications, package details, sourcing options, and practical design guidance. It also separates the ROMless W77L032A configuration from related flash-based W77M032A devices, helping engineers compare memory architecture, clock requirements, and PCB compatibility before selection.

RFQ Contact
W77L032A25PL - 25MHz ROMless 8051 MCU | Nuvoton
W77L032A25PL

W77L032A25PL - 25MHz ROMless 8051 MCU | Nuvoton

Nuvoton Technology Corporation W77L032A25PL is a ROMless 8-bit 8051-compatible microcontroller rated up to 25 MHz, supplied in a 44-pin PLCC package. It operates from 2.7 V to 5.5 V and provides 1K x 8 bits of RAM, an 8-bit data bus, and up to 36 I/O positions according to the catalog information. Its ROMless architecture separates execution storage from the controller, allowing the external program-memory configuration to be selected for the target application. An 8051 microcontroller is an 8-bit embedded-control component that combines a CPU core, memory interfaces, timers, serial communication, and parallel I/O. Within the product hierarchy, the W77L032 belongs to the 8051-compatible microcontroller family, which sits above general-purpose microcontrollers and below the broader category of embedded processors and semiconductors. The principal benefits of this device are its 25 MHz maximum clock, broad 2.7 V to 5.5 V supply range, and generous I/O count for a small 8-bit controller. ROMless operation is particularly useful when code storage must remain external or when a common controller can support several memory configurations. The 44-pin PLCC package also provides a leaded form factor that can simplify inspection, assembly, and prototyping compared with a very small surface-mount package. The W77 architecture uses an 8-bit data bus and provides 1K x 8 bits of RAM. One catalog entry identifies an internal oscillator, while another listing describes the ROM type as flash despite the primary product descriptions identifying the device as ROMless. Engineers should therefore consult the manufacturer datasheet and memory-interface section when confirming the exact external-memory configuration, oscillator arrangement, and timing characteristics for a production design. Typical applications include industrial controllers, serial-interface equipment, data acquisition modules, embedded keypads, motor-control interfaces, and legacy 8051 peripheral controllers. The combination of 36 I/O positions and a 25 MHz clock allows the device to coordinate multiple discrete inputs and outputs while retaining the straightforward programming model associated with 8051-compatible controllers. Design planning should begin with the 44-pin PLCC footprint, external program-memory requirements, oscillator connections, reset behavior, and the allocated I/O functions. Validate every pin against the current manufacturer datasheet before layout release, particularly where firmware depends on external memory timing or specific peripheral multiplexing. This product page consolidates the available electrical, package, sourcing, and replacement information into an engineering-focused selection guide. It also highlights the verified drop-in family options, application guidance, comparison limits, and design checks needed to evaluate the W77L032A25PL for an embedded-control design.

RFQ Contact
W77L058A25FL - 8-Bit 80C51 32KB Flash 25MHz MCU | Nuvoton
W77L058A25FL

W77L058A25FL - 8-Bit 80C51 32KB Flash 25MHz MCU | Nuvoton

The Nuvoton Technology Corporation W77L058A25FL is an 8-bit flash microcontroller built on a 4-cycle 8051 core, with 32 KB of on-chip flash memory, a 25 MHz maximum operating frequency and a 2.7 V to 5.5 V supply range, packaged in a 44-pin MQFP (10 x 10 mm) surface-mount package. It targets cost-sensitive, high-volume consumer and industrial control designs that need a small footprint, wide supply tolerance and legacy 8051 toolchain compatibility. An 8-bit microcontroller (MCU) is a self-contained computing element that integrates a CPU core, program memory, data memory and peripherals onto a single die. The classic 8051 core, also called an MCS-51 or C51, remains the most widely installed 8-bit architecture in the industry, and its 4-cycle pipeline (rather than the original 12-cycle design) roughly triples instruction throughput compared with an early 8051. As a member of the wider microcontroller -> embedded processor -> semiconductor hierarchy, this part targets cost-sensitive embedded control rather than signal processing or connectivity. Key features of the W77L058A25FL include 32 KB of flash program memory for in-circuit programmable firmware, a 25 MHz clock rating that delivers up to 25 million instruction cycles per second, and a 2.7 V to 5.5 V operating range that covers both 3.3 V and 5 V system rails. Because the core is an 8051 derivative, existing assembly routines and Keil C51, SDCC or IAR 8051 toolchains can be reused without architectural rework, protecting firmware investment. The 44-pin MQFP (10 x 10 mm) footprint balances I/O count against board area, giving designs four 8-bit ports plus dedicated reset, clock and programming pins in a compact square surface-mount package suitable for automated assembly. As an MCU, the device integrates flash, RAM and standard 8051 peripherals (timers, serial ports and interrupt controller) on one die, eliminating the need for external program memory. Typical applications include small appliance and kitchen equipment controllers, LED driver and dimming modules, household meter and energy-monitoring front panels, industrial sequence controllers, keyboard and panel interface hubs, and compact sensor-node controllers where a 25 MHz 8051 core is sufficient and a 32 KB firmware budget is adequate. When designing around the W77L058A25FL, verify the pin multiplexing of each port against the peripheral assignment required by your firmware, and keep the decoupling network short: a 0.1 uF ceramic plus a 4.7 uF bulk capacitor at VDD/VSS minimizes brownout risk during flash write cycles. The 44-pin square outline also demands careful lead-frame tooling, so confirm the recommended land pattern and reflow profile before committing to volume production. This page consolidates distributor availability, pin- and package-matched drop-in alternatives from the same 8051 family, and practical layout and toolchain notes that go beyond the manufacturer datasheet.

RFQ Contact
W77L058A25PL - 25MHz 8-Bit 8051 MCU | Nuvoton | PLCC-44
W77L058A25PL

W77L058A25PL - 25MHz 8-Bit 8051 MCU | Nuvoton | PLCC-44

The Nuvoton Technology Corporation W77L058A25PL is a 25 MHz, 8-bit 8051-compatible microcontroller with 32 KB of flash program memory, 1 KB of RAM, and 36 I/O pins in a 44-pin PLCC package. It operates from 2.7 V to 5.5 V and is designed for embedded control systems that require legacy 8051 software compatibility, moderate processing speed, and a compact leaded-chip package. An 8-bit microcontroller is a programmable semiconductor device that integrates a CPU, program memory, data memory, I/O ports, timers, and communication peripherals on one device. The W77L058A25PL belongs to the 8051 microcontroller family within the broader embedded-controller hierarchy. Its four-cycle 8051 core provides predictable instruction execution for motor controls, instrumentation, industrial controllers, and legacy equipment. Key features include a 25 MHz maximum operating frequency, 32 KB of flash memory, 1 KB of internal RAM, and 36 I/O lines. The 2.7 V to 5.5 V supply range allows operation from regulated 3.3 V and 5 V rails. Its 44-pin PLCC package provides 36 usable I/O pins for digital interfaces, control signals, displays, and external peripheral connections. The device retains compatibility with the established 8051 architecture while using flash rather than legacy EPROM or mask-programmed memory. This makes it suitable for designs migrating from older 8051 controllers, as well as new embedded products where an 8-bit control engine remains preferable to a higher-cost application processor. The operating frequency provides additional timing margin for interrupt-driven control, serial communication, and periodic sensing tasks. Typical applications include industrial automation modules, motor and relay controllers, programmable logic controllers, data acquisition equipment, appliance controllers, LED sign controllers, and communication interfaces. Its 36 I/O pins are particularly useful when a design needs multiple discrete control connections without using a larger programmable logic device. PCB design should preserve the PLCC footprint, socket or land pattern, pin numbering, and adequate clearance around the leaded package. Designers should also account for the 2.7 V minimum operating voltage, configure the oscillator and reset circuitry according to the manufacturer datasheet, and validate unused I/O states before production. A socket can simplify prototype replacement but increases board height and contact resistance compared with direct soldering. This product page consolidates the verified electrical identity, package information, sourcing path, application guidance, and qualified engineering trade-offs into one technical reference. It also distinguishes the W77L058A25PL from alternatives that may offer similar general-purpose microcontroller functions without providing the required package-level drop-in compatibility.

RFQ Contact
W77L516A25FL - 25MHz 64KB 8051 MCU | Nuvoton | Embedded Control
W77L516A25FL

W77L516A25FL - 25MHz 64KB 8051 MCU | Nuvoton | Embedded Control

The Nuvoton Technology Corporation W77L516A25FL is an 8-bit W77 8051-compatible microcontroller operating at 25 MHz, with 64 KB of built-in Flash program memory and 1 KB of internal RAM. The device is packaged in a 44-pin BQFP package measuring 10 mm by 10 mm and provides 36 general-purpose I/O pins for embedded control systems. An 8051 microcontroller is a compact CISC-based control processor that integrates CPU registers, program memory, data memory, and peripherals into one device. Its place in the product hierarchy is microcontroller → embedded processor → programmable controller → semiconductor. The W77L516A25FL combines the widely established 8051 instruction set with on-chip Flash, making it suitable for products that benefit from legacy 8051 code compatibility while requiring a modern nonvolatile program-memory implementation. Key features include a 25 MHz operating speed, 64 KB of Flash organized as 64K x 8, 1 KB of SRAM organized as 1K x 8, and 36 I/O lines. The operating-voltage listing spans 2.7 V to 5.5 V, while another technical listing identifies 4.5 V as a relevant operating-voltage value. The device also includes an internal oscillator according to the component specifications. These characteristics position it for compact embedded controllers, industrial automation modules, and cost-sensitive control products with moderate processing requirements. The W77L516A25FL belongs to Nuvoton's W77 series and retains an 8-bit MCU architecture rather than using a 32-bit core. Flash memory allows firmware to be stored without an external program-memory device, reducing the component count in a finished controller. The 36 available I/O pins provide substantial interface capacity for digital inputs, outputs, indicators, and external control signals, although the exact peripheral multiplexing must be assigned from the manufacturer pin-description table. Typical application areas include industrial equipment interfaces, data-collection terminals, programmable control panels, building automation equipment, and compact embedded control modules. A 25 MHz clock provides useful processing headroom for 8051-based supervisory tasks, state machines, communication routines, and peripheral coordination. The 44-pin package also leaves a broader interface budget than many smaller microcontroller packages while remaining compact enough for embedded boards. When laying out a W77L516A25FL board, begin with the manufacturer pin-description table and assign every power, ground, reset, clock, and I/O connection explicitly. Confirm the operating rail required by the selected design, decouple each supply connection locally, and route oscillator and sensitive signals away from high-current switching nodes. The 8051 architecture is mature, but firmware timing, peripheral selection, and pin multiplexing must still be checked against the device documentation. This product page consolidates the core electrical specifications, package information, sourcing details, application guidance, and engineering considerations into a concise engineering reference. It is intended to help designers identify whether the W77L516A25FL's Flash memory, 25 MHz speed, 36 I/O pins, 44-pin BQFP package, and 8051 compatibility fit an embedded-control design.

RFQ Contact
W77L516A25PL - 25MHz 8-Bit 8051 MCU, 64KB Flash | Nuvoton
W77L516A25PL

W77L516A25PL - 25MHz 8-Bit 8051 MCU, 64KB Flash | Nuvoton

The Nuvoton Technology Corporation W77L516A25PL is an 8-bit 8051-compatible microcontroller operating at 25 MHz, with 64 KB of flash program memory, 1 KB of RAM, and 36 I/O lines in a 44-pin PLCC package. It combines the familiar 8052 instruction set with a redesigned processor core that executes instructions approximately 1.5 to 3 times faster than a traditional 8051 at the same clock frequency. The W77L516A25PL is designed for embedded-control applications requiring deterministic serial communication, timer resources, parallel I/O, and programmable flash storage. An 8-bit microcontroller is a compact processor intended to control embedded systems rather than execute a desktop operating system. Within the semiconductor hierarchy, the W77L516A25PL belongs to the 8051-compatible microcontroller class and retains the standard 8052 peripheral model, including four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex serial port, and interrupt resources. Its instruction-set compatibility allows legacy 8051-oriented code and development practices to be retained during product modernization. The principal device characteristics include 64 KB of flash program memory, 1 KB of on-chip RAM, 36 I/O pins, and a 25 MHz operating frequency. Additional integrated resources identified for this device include a serial port, power-on reset, and a watchdog timer. The redesigned core removes wasted clock and memory cycles, so software timing can improve without changing the external clock speed. Flash memory also provides a more flexible program-storage medium than mask-programmed or one-time-programmable microcontroller implementations. The 44-pin PLCC package provides a leaded, socket-compatible format suited to controllers, interface modules, industrial control boards, and legacy system upgrades. Its pin-compatible 8052 heritage simplifies board-level continuity when a design moves from a conventional 8051-class controller to this faster implementation. Designers should still validate the clock configuration, peripheral allocation, reset behavior, and memory map in the target system rather than assuming every legacy peripheral behaves identically. Typical uses include industrial equipment interfaces, serial protocol bridges, data acquisition modules, appliance controllers, embedded instrumentation, and communication adapters. The combination of four parallel I/O ports, three timers, serial communications, and 36 I/O lines is especially useful for systems that must connect switches, sensors, displays, relays, and legacy peripherals while maintaining predictable control timing. The principal design consideration is preserving compatibility at both software and board level. Confirm that the chosen oscillator and reset circuit meet the datasheet requirements, allocate every pin according to the manufacturer's pin description, and include adequate decoupling. Because this is a legacy-compatible 8-bit architecture, migration planning should also include confirmation of compiler support, bootloader behavior, peripheral register mapping, and any source-code changes required for the faster core. This page combines the manufacturer's device data with practical selection guidance, application context, package information, and verified sourcing links. It is intended to help engineers determine whether the W77L516A25PL fits an existing embedded-control design and how to evaluate compatible W77-family options without overlooking memory, timing, package, or toolchain requirements.

RFQ Contact
W77L532A25FL - 8-Bit 128KB Flash MCU | Nuvoton
W77L532A25FL

W77L532A25FL - 8-Bit 128KB Flash MCU | Nuvoton

The Nuvoton W77L532A25FL is an 8-bit embedded microcontroller with 128KB of Flash program memory, 36 I/O pins, and a 25 MHz maximum operating frequency. It is packaged in a 44-pin BQFP and includes an 8051 core, serial-port connectivity, a power-on reset peripheral, and a watchdog timer. The device is identified as an active part and is positioned for compact embedded-control designs that require nonvolatile firmware storage and a broad external bus interface. An 8-bit microcontroller is a semiconductor integrated circuit designed to execute embedded instructions using an 8-bit data path. The W77L532A25FL belongs to the 8051-compatible microcontroller hierarchy, combining a CPU core, Flash memory, RAM, serial communication, and dedicated system-control peripherals in one package. Its EBI/EMI interface permits connection to external memory or peripheral devices when the on-chip resources are insufficient. The principal feature set includes 128KB, or 128K × 8, of Flash program memory and 1K × 8 bytes of RAM. Its 36 available I/O lines support peripheral functions and general digital control. At up to 25 MHz, the MCU provides a defined operating speed for embedded tasks. Program-once development is supported by the Flash memory architecture, while power-on reset and watchdog-timer functions improve recovery after startup errors or unexpected program stalls. The W77L532A25FL is an 8-bit MCU rather than a high-performance 32-bit processor. Its architecture is appropriate for deterministic control tasks, data acquisition, communication bridging, keypad and display control, and compact industrial equipment. The 44-pin BQFP exposes substantially more I/O than a small lead-frame package, making external sensors, displays, relays, and memory devices easier to connect while still supporting surface-mount assembly. Typical applications include programmable control panels, instrumentation, serial-interface adapters, industrial controllers, and embedded peripheral modules. Its 36 I/O pins can distribute control signals across multiple external devices, while the EBI/EMI interface provides a route to additional bus-connected components. The serial port is useful for host communication, configuration transfer, firmware updates, or linking the controller to another embedded system. The main design consideration is power and clock planning. Engineers should use the manufacturer's oscillator and reset guidance when creating the clock network, preserve the required supply decoupling arrangement, and confirm that every signal connected to the 36 available I/O pins has a suitable input level. Firmware should also enable the watchdog timer in applications where a hung task could create unsafe equipment behavior. This product record combines the part's core embedded specifications, package information, sourcing structure, and engineering guidance in one concise reference. It supports initial design review by connecting the 8051 core, 128KB Flash memory, 1K × 8 RAM, 25 MHz speed, and 36 I/O capabilities with practical implementation considerations for reliable embedded systems.

RFQ Contact
W77L532A25PL - 8-Bit 25MHz 128KB Flash MCU | Nuvoton
W77L532A25PL

W77L532A25PL - 8-Bit 25MHz 128KB Flash MCU | Nuvoton

Nuvoton Technology Corporation W77L532A25PL is an 8-bit W77 8051-compatible microcontroller operating at up to 25 MHz, with 128 KB of embedded Flash program memory and 36 I/O pins in a 44-pin PLCC package. The device combines 128 KB (128K x 8) Flash memory with 1K x 8 RAM and is designed for embedded control systems that require deterministic 8-bit processing and a compact leaded package. A microcontroller is a programmable semiconductor that integrates a CPU, memory, I/O, and peripherals into one device. In the product hierarchy, the W77L532A25PL is an 8-bit MCU, part of the 8051-compatible microcontroller family, and a member of the broader embedded-processing and semiconductor categories. It is intended for control rather than general-purpose computing, making it suitable for industrial controllers, embedded instruments, data-acquisition systems, and compact automation products. The principal device characteristics are a 25 MHz maximum operating frequency, 128 KB of Flash program memory, 1K x 8 RAM, and 36 available I/O lines. Flash program memory supports firmware storage without a separate external memory device, while the 44-pin PLCC package provides a leaded, socket-compatible mechanical format for prototypes and established control-board assemblies. The component is also identified as supporting 3.3 V and 5 V operation, enabling its use in mixed-voltage embedded equipment. The W77L532A25PL uses the 8-bit W77 8051-compatible instruction set and CISC-oriented embedded-control architecture. Its 36 I/O pins provide connectivity for digital sensors, relays, displays, communication interfaces, and actuator-control signals. This combination of moderate clock speed, internal Flash, and a substantial I/O count is useful when the design requires predictable peripheral control without the complexity of a higher-performance processor. Exact peripheral allocations and electrical limits must be confirmed from the manufacturer’s pin-description table before PCB routing. Typical applications include programmable industrial controls, serial protocol bridges, relay and solenoid controllers, embedded measurement instruments, test fixtures, and legacy 8051 peripheral expansion. The 128 KB program capacity is particularly useful for firmware containing communications tables, calibration constants, diagnostics, and application-specific state machines. The 36 I/O lines can distribute control traffic across sensors and actuators while keeping the design within a single package. When integrating the controller, begin with the exact pin-description table, oscillator requirements, and recommended decoupling configuration in the manufacturer datasheet. Preserve the PLCC land pattern, observe the stated operating-voltage range, and validate unused pins according to the device documentation. Because 8051 peripherals and interrupt behavior are architecture-specific, confirm timer, serial, and interrupt resources before assigning them to time-critical functions. This product page combines the key memory, speed, I/O, and package characteristics with application guidance, pin-placement cautions, and a same-package alternative comparison. It also provides a practical sourcing path through the Request a Quote form, helping engineers evaluate whether the W77L532A25PL fits both the original PCB footprint and the required embedded-control functionality.

RFQ Contact