ADC/DAC
بەرهەمەکان (3,600+)
PCM1760U-X - 20-Bit Dual ADC, 48 kHz | Texas Instruments
The Texas Instruments PCM1760U-X is a 20-bit dual-channel analog-to-digital converter with a 48 kHz sampling rate in a 28-pin SOIC package. It is designed for applications requiring simultaneous or interleaved conversion of two analog signals with consistent 20-bit digital output. An audio ADC is a semiconductor that converts continuously varying analog voltages into digital sample data for processing, storage, transmission, or playback. The PCM1760U-X belongs to the ADC/DAC category and uses enhanced noise-shaping technology to reduce quantization-related noise within the audio band. Its dual-channel architecture allows two inputs to share one converter package while retaining separate digital output paths. The primary verified characteristics are a resolution of 20 bits, two analog input channels, a 48 kHz sampling rate, and a 28-pin SOIC package. The 20-bit word length permits 1,048,576 distinct codes across the converter's full-scale range, while the enhanced noise-shaping approach moves shaped quantization noise away from the most sensitive portion of the audio spectrum. The exact dynamic range, analog input range, SNR, THD, clock requirements, and supported interface modes should be confirmed against the manufacturer datasheet before final circuit design. The PCM1760U-X is associated with Burr-Brown audio converter designs and is intended for precision digital audio equipment. Potential uses include stereo audio capture, professional audio interfaces, digital mixers, consumer playback equipment, and embedded audio subsystems. Two-channel capture makes the converter particularly useful when left and right signals must be sampled together and processed through a consistent clock and data architecture. Clocking and digital-interface compatibility are the most important design checks. The supporting clock source, master clock relationship, serial-data format, word length, and required control signals must match the host processor or audio codec. Layout should keep analog input traces short, separate from digital clock and data paths, and terminated according to the impedance of the implemented board stack-up. This product page combines the confirmed converter specifications, package information, application guidance, and candid replacement limitations. Before committing to a layout, verify analog input range, full-scale scaling, minimum operating voltage, clock frequency, and digital interface details in the Texas Instruments PCM1760U datasheet.
PCM1770PW - 24-Bit Stereo DAC with HP Amplifier | TI
Texas Instruments PCM1770PW is a low-voltage, low-power 24-bit stereo digital-to-analog converter with an integrated headphone amplifier, operating from a 1.6 V to 3.6 V supply in a 16-pin TSSOP package. It supports 50 kSPS conversion, I2S audio data, and a signal-to-noise ratio of 98 dB according to the Texas Instruments product page. A digital-to-analog converter, or DAC, converts digital audio samples into proportional analog voltages. In a stereo implementation, two converters reconstruct left and right channels from an I2S source. The PCM1770PW combines that conversion function with headphone-driver circuitry and support logic, reducing the number of discrete components required in portable audio equipment while retaining a compact surface-mount footprint. The converter uses TI’s enhanced multilevel architecture, which applies noise shaping and multilevel amplitude quantization. These techniques support efficient low-voltage operation and improved dynamic performance. The integrated headphone amplifier includes software control, allowing the host processor to adjust the relevant operating mode without relying on a separate analog control interface. PCM1770PW is identified as a 24-bit DAC rated for 50 kSPS operation. Its CMOS monolithic construction supports low-power audio signal chains, while the 1.6 V to 3.6 V operating range fits battery-powered and portable systems. The device accepts 3-wire I2S serial audio data, making it suitable for systems whose digital audio source already uses that interface. Typical applications include portable digital audio players, headphone-equipped personal audio products, compact consumer audio equipment, and embedded systems requiring a stereo conversion stage with a local headphone output. Integrating the DAC and headphone amplifier supports a shorter analog signal path while reducing board area compared with separate conversion and amplification stages. Circuit design should account for the low supply voltage and analog-output implementation required by the manufacturer datasheet. Decoupling, output loading, digital-interface timing, and headphone-output stability determine practical performance. Before production release, use the pin-description table and recommended application circuit in the manufacturer documentation to assign PCB tracks and select external components. This product record combines the manufacturer’s architecture and device specifications with application guidance, package information, engineering design notes, and a side-by-side comparison. These resources help engineers assess the PCM1770PW for compact stereo audio designs while separately confirming electrical limits and pin-level implementation details.
PCM1770PWR - 24-Bit Stereo DAC with Headphone Amp | Texas Instruments
Texas Instruments PCM1770PWR is a 24-bit, low-power stereo digital-to-analog converter with an integrated headphone amplifier, supporting audio sampling rates up to 50 kHz through an I2S-compatible interface. The device is offered in a 16-pin TSSOP package and is designed for compact audio systems requiring a low-noise stereo conversion path and direct headphone drive. It provides 98 dB SNR and software-controlled operation. A digital-to-analog converter, or DAC, is an integrated circuit that converts digital audio samples into continuous analog voltage signals. In the broader signal-chain hierarchy, a stereo DAC belongs to the ADC/DAC class of interface and data-conversion ICs. A DAC is commonly positioned between a digital audio source, such as a USB audio interface or digital audio processor, and an analog output stage, where it supports headphones, powered speakers, line inputs, or audio analog-to-digital converters. The PCM1770's 24-bit resolution supports high-fidelity audio formats, while its 50 kHz sampling capability covers standard digital-audio rates used in compact consumer and communication equipment. Its integrated headphone circuitry reduces the need for a separate output amplifier in space-constrained designs. The software-control capability provides a selectable operating interface, and the 98 dB signal-to-noise ratio is a key measure of the converter's ability to preserve low-level audio information without excessive output noise. The PCM1770 is a CMOS monolithic integrated circuit combining stereo digital-to-analog converters, headphone circuitry, and support functions. TI describes its converter implementation as an enhanced multilevel architecture using noise shaping and multilevel amplitude quantization. These techniques improve dynamic performance while supporting low-voltage, low-power operation in a compact surface-mount package. Typical uses include portable headphone audio, digital-audio-player analog outputs, multimedia terminal analog sections, and compact communication equipment. In these systems, the converter can accept digital audio from a host processor and produce stereo analog signals for headphone or line-level output stages. The integrated headphone amplifier is especially useful where component count, board area, and power consumption are constrained. When designing around PCM1770PWR, preserve adequate layout separation between digital and analog signals, place required bypass capacitors close to their supply pins, and route headphone outputs away from sensitive input and control traces. Confirm that the external output network and load match the headphone-amplifier requirements in the manufacturer datasheet before finalizing the analog output stage. This product record combines the manufacturer specifications, interface details, package information, application guidance, and verified sourcing links for PCM1770PWR. It also provides practical PCB and signal-integrity considerations that help engineers move from component selection to a production-ready stereo audio design.
PCM1770RGAR - 24-Bit Stereo DAC with HP Amp, 98dB SNR | Texas Instruments
The Texas Instruments PCM1770RGAR is a 24-bit stereo audio digital-to-analog converter with an integrated headphone amplifier and software-controlled output switching, delivering 98 dB SNR at up to 48 kHz sampling in a 20-pin VQFN (RGA) 4.2 x 4.2 mm package. An audio DAC is a signal-chain integrated circuit that converts digital audio samples into an analog voltage; a DAC with an integrated headphone amplifier adds a low-noise current/voltage output stage so that headphones can be driven directly without a separate amplifier chip. In the component hierarchy the PCM1770RGAR sits as an audio codec-class converter: stereo DAC -> audio converter IC -> signal-chain semiconductor, one tier above discrete op-amp output stages and one tier below a full audio codec with analog inputs. Key features include 24-bit resolution, 98 dB signal-to-noise ratio, a 2-channel architecture with no analog input paths, an SPI control port for register-based configuration, and single-supply operation from 1.6 V for low-voltage portable systems. The headphone output stage is controlled in software, allowing mute and channel-routing functions to be driven from the host microcontroller rather than external hardware. Internally the device is a CMOS monolithic converter built on TI's enhanced multilevel architecture, employing noise shaping and multilevel amplitude quantization to push quantization noise out of the audio band while keeping the required passband filter simple. The 20-pin VQFN (RGA) package is a leadless HVQCCN outline with a thermal and ground pad, which lowers parasitic inductance on digital lines and keeps the footprint smaller than the 16-pin TSSOP alternative offered in the same family. Typical uses include USB and Bluetooth audio dongles, portable media players and handsets with analog headphone output, digital mixing consoles and broadcast monitors that need a low-noise local DAC, and instrumentation or test equipment that generates analog audio from a digital source. In each case the part replaces a discrete DAC plus output buffer and reduces both board area and assembly count. When laying out the PCB, place the analog and digital supplies' decoupling capacitors directly at the package pins, bond the exposed pad to a solid ground plane, and keep the SPI clock and data traces short and referenced to a quiet ground region. Master clock jitter and the ratio between master clock and the audio sample rate determine the achievable dynamic range, so a clean, low-jitter clock source is as important as the filter selection. This page consolidates the device specifications, a package-matched drop-in alternative list, a parameter-by-parameter comparison and practical layout notes into one engineering-focused reference that the manufacturer datasheet alone does not provide.
PCM1771PW - 24-Bit Stereo Audio DAC with Headphone Amp | TI
Texas Instruments PCM1771PW is a low-voltage, low-power CMOS stereo digital-to-analog converter with an integrated headphone amplifier in a 16-pin TSSOP package. The device converts 24-bit digital audio into two analog output channels and supports I2S-format serial audio data. According to the Texas Instruments PCM1771 product page, the PCM1771 family also includes a 20-pin VQFN option, while the PW orderable part is specified in TSSOP-16. The PCM1771 belongs to the audio DAC hierarchy: DAC → digital-to-analog converter → audio signal converter → mixed-signal semiconductor. This integration is valuable in compact portable audio products because a separate headphone-output amplifier and output-filter stage are not required for a basic line-output or headphone-driving topology. The TI product page states that the converters use an enhanced multilevel architecture with noise shaping and multilevel amplitude quantization to improve dynamic performance. Principal specifications identified for PCM1771PW include a 24-bit resolution, a 50 kSPS maximum sampling rate, I2S serial audio support, and a 1.6 V to 3.6 V operating supply range. Distributor listings also identify a typical dynamic range of 98 dB. These characteristics place the converter in the low-power, portable-audio class while providing enough resolution for CD-compatible 44.1 kHz playback and higher-rate digital audio sources. The integrated headphone circuitry provides two analog output paths for stereo playback. Exact output-current limits, headphone-output THD+N under defined load conditions, and pin-level signal names are not stated in the available product listings, so engineers should confirm them in the manufacturer data sheet before setting output gain, loading, or PCB routing. Digital audio is accepted through the serial interface, while the analog side requires appropriate output filtering, decoupling, and return-path layout. Typical PCM1771PW applications include portable digital audio players, compact USB or Bluetooth audio accessories, digital mixing consoles, portable audio monitors, and USB-controlled headphone amplifiers. The low operating-voltage range allows connection to 1.8 V, 2.5 V, or 3.3 V system rails, while the TSSOP-16 footprint supports compact, high-density layouts. Use the pin-description table and recommended application circuit in the PCM1771 data sheet when assigning nets and selecting bypass capacitors. This page combines the confirmed PCM1771PW specifications, package information, sourcing evidence, and practical design guidance with an explicit separation between published facts and values that still require confirmation. It is intended to accelerate initial component selection while directing final schematic and layout approval to the authoritative Texas Instruments documentation.
PCM1771RGA - 24-Bit Stereo Audio DAC with Headphone Amp | TI
Texas Instruments PCM1771RGA is a 24-bit low-power stereo audio digital-to-analog converter with integrated headphone amplifier circuitry, 50 kHz sampling capability, and an I2S audio interface. The device is offered in a 20-pin VQFN RGA package measuring 4.2 mm by 4.2 mm and is specified for 98 dB signal-to-noise ratio. It combines stereo DAC conversion, headphone amplification, and supporting circuitry in one CMOS monolithic IC for compact audio equipment. An audio DAC is a signal-conversion integrated circuit that transforms digital audio samples into an analog voltage waveform suitable for amplification, loudspeaker drive, or headphone output. PCM1771 belongs to the DAC hierarchy within audio converters, ADC/DAC integrated circuits, and broader semiconductor components. Its integrated headphone circuitry reduces the number of external analog-output stages needed in portable and multimedia equipment while retaining a compact surface-mount footprint. Key features include 24-bit resolution, a maximum sampling rate of 50 kHz, 98 dB SNR, stereo DAC channels, an I2S-compatible digital interface, and a low-power CMOS implementation. The enhanced multilevel converter architecture uses noise shaping and multilevel amplitude quantization to improve dynamic performance. A hardware-control headphone-amplifier option supports systems requiring direct control of the headphone-output operating state. The PCM1771 combines its digital input section, stereo conversion core, analog output circuitry, and headphone amplifier within one package. Its I2S interface allows connection to a digital-audio source such as a sound-card controller, portable-media processor, or audio interface. Noise shaping redistributes quantization noise away from the most perceptually important audio band, while 24-bit quantization supports a high-resolution representation of each sample. The 4.2 mm by 4.2 mm VQFN-20 package supports compact PCB layouts but requires careful exposed-pad thermal and layout management. Typical applications include headphone-equipped portable players, digital audio accessories, multimedia speakers, USB or portable-audio interfaces, consumer electronics, and embedded audio systems. The integrated headphone stage is particularly useful when the design requires analog headphone output without a separate headphone-amplifier IC. Systems requiring simultaneous microphone capture and headphone playback should also evaluate the clocking, interface format, and analog routing of the complete design rather than assuming every codec requirement is covered. The primary design considerations are correct I2S data and clock connections, compliant digital supply sequencing, analog-output filtering, and the PCB treatment of the VQFN exposed pad. Keep digital return currents away from the analog output and headphone-driver paths, place decoupling capacitors near their associated supply pins, and use a ground plane that does not split the return network beneath the converter. Confirm the selected output mode and filter components against the manufacturer datasheet before releasing a PCB layout. This product data consolidates the exact PCM1771RGA package, interface, resolution, sampling, SNR, temperature, and conversion-architecture details with practical application guidance, sourcing instructions, and same-package family comparisons. It is designed to help engineers determine whether the converter suits a new audio design and how to evaluate qualified alternatives before committing a board layout.
PCM1772PW - 24-Bit Stereo Audio DAC | Texas Instruments
The Texas Instruments PCM1772PW is a 24-bit, low-power stereo audio digital-to-analog converter with integrated line-out circuitry and software control, housed in a 16-pin TSSOP package. It supports I2S audio data at sample rates up to 50 kSPS and is designed to provide 98 dB signal-to-noise ratio for compact audio systems. The device accepts digital stereo audio, converts it into analog left and right channels, and drives the line outputs through its integrated amplifier circuitry. An audio DAC is a signal-conversion IC that transforms digital audio samples into continuous analog voltages suitable for amplification, headphone stages, mixer inputs, or line-level equipment. It belongs to the digital-to-analog converter category within broader data-conversion and signal-processing integrated circuits. Its digital interface connects to an audio codec or processor, while the line outputs connect to the next analog stage in the signal chain. The PCM1772PW combines a 24-bit conversion resolution, a maximum 50 kSPS sampling rate, and 98 dB SNR in one low-power CMOS device. Software-controlled operation allows the host processor to manage supported device functions without a dedicated control microcontroller. Its stereo line-out architecture reduces the need for external output amplifiers in conventional line-level audio designs, although output loading, coupling, and headroom still require careful evaluation. Texas Instruments describes the converter architecture as an enhanced multilevel design using noise shaping and multilevel amplitude quantization. These techniques are intended to improve dynamic performance and clock-jitter tolerance compared with a basic binary conversion approach. The PCM1772 and related PCM family devices are monolithic CMOS integrated circuits combining stereo DACs, line-out circuitry, and support functions in compact packages. Typical uses include digital active speakers, compact audio appliances, consumer audio equipment, computer peripherals, and embedded audio systems that receive standard I2S streams. In these applications, the PCM1772PW can establish an analog line output close to the digital audio source, reducing system size while retaining a conventional stereo line-output interface. Its 24-bit resolution is also useful in designs where the host digital audio source provides higher-resolution samples. The most important design check is the relationship between the digital audio source, clocking method, supported audio format, analog output loading, and power-supply arrangement. Use the pin-description table and recommended application circuit in the manufacturer datasheet when assigning tracks, selecting output components, and validating signal levels. Confirm whether the required I2S master or slave relationship and clock configuration match the surrounding codec or processor. This product page consolidates the confirmed PCM1772PW capabilities, package information, sourcing workflow, and engineering guidance. It also distinguishes confirmed same-family alternatives from unsupported cross-package substitutions, helping engineers identify candidates while still requiring a final pin, timing, interface, and acoustic review before PCB release.
PCM1772PWR - 24-Bit Stereo DAC with Line Output | Texas Instruments
The Texas Instruments PCM1772PWR is a 24-bit stereo audio digital-to-analog converter with integrated line-output circuitry, designed for low-voltage and low-power audio systems. It uses a serial I2S-compatible interface, supports a 50 kHz sampling rate, and provides a 16-pin TSSOP (PW) package. The device is identified by TI as a 98 dB SNR low-power stereo DAC with line-out and software control. A DAC converts digital audio samples into an analog voltage that can drive an audio amplifier, headphone stage, mixer, or line-level input. The PCM1772PWR is a stereo converter with two analog output channels and integrated line-output circuitry, reducing the need for separate output buffers in many compact audio products. Its 24-bit data resolution is suitable for CD-derived audio, digital media players, communication terminals, and embedded audio equipment. The PCM1772 uses TI’s enhanced multilevel delta-sigma architecture, combining noise shaping with multilevel amplitude quantization to improve dynamic performance and tolerance to clock and data errors. The 98 dB SNR specification indicates a low-noise conversion path, while the integrated line-output amplifier simplifies analog routing to downstream circuitry. The serial three-wire interface reduces pin count compared with parallel DAC architectures and supports digital audio from microcontrollers, decoders, and audio processors. Typical applications include portable and compact audio equipment, USB and digital-audio accessories, communication consoles, consumer audio modules, and low-voltage stereo playback systems. The 16-pin TSSOP package also simplifies PCB assembly in designs where surface-mount construction is required. When designing around the PCM1772PWR, pay particular attention to digital-interface timing, analog output filtering, supply decoupling, and the distinction between digital ground and analog ground connections. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning signal, power, and return paths on the PCB.
PCM1772RGA - 24-Bit Stereo DAC with Line-Out | Texas Instruments
The Texas Instruments PCM1772RGA is a low-voltage, low-power CMOS stereo audio digital-to-analog converter with an integrated line-out amplifier. The device accepts 24-bit digital audio at sampling rates up to 50 kHz through an I2S interface and delivers a 98 dB signal-to-noise ratio according to the manufacturer product page. It is supplied in a 20-pin VQFNP (RGA) package measuring 4.2 mm by 4.2 mm. A stereo DAC converts digital audio samples into analog voltage signals suitable for headphone, line-level, mixer, or amplifier inputs. Within the broader power-management and signal-chain hierarchy, the PCM1772 sits between a digital audio source and an analog output stage. Its integrated line-out circuitry reduces the need for a separate output buffer when the destination accepts line-level signals. Key features include a 24-bit conversion interface, support for sampling rates through 50 kHz, a 98 dB SNR rating, integrated stereo line-out amplification, and software control of the line-out function. The low-power architecture targets portable and space-constrained audio equipment where converter efficiency, small package area, and short analog output paths are important. The PCM1772 uses an enhanced multilevel delta-sigma conversion architecture designed to reduce noise and distortion. Its CMOS implementation combines the stereo converters, line-out circuitry, and support functions in one package. The 4.2 mm by 4.2 mm footprint supports compact designs while the 20-pin package exposes digital inputs, analog outputs, configuration control, and supply connections. Typical applications include digital audio players, portable media equipment, USB and embedded audio accessories, soundbar signal chains, multimedia terminals, and consumer audio products requiring a low-power stereo DAC with integrated line outputs. The device is also suitable for prototype evaluation of interface-compatible audio architectures. When laying out the circuit, keep the digital interface traces away from the analog output paths and provide local decoupling at the supply pins. The PCB footprint and exposed-pad or thermal-layout requirements must follow the package drawing in the manufacturer datasheet. Verify digital input levels, master-clock requirements, and output-loading conditions against the system audio specification before releasing the layout.
PCM1773PW - 24-Bit Stereo Audio DAC | Texas Instruments
Texas Instruments PCM1773PW is a 24-bit low-power stereo digital-to-analog converter with an integrated line-out amplifier, 98 dB SNR, support for I2S audio data, and a 16-pin TSSOP package. The converter operates across a 0°C to 70°C temperature range and uses an enhanced multilevel architecture with noise shaping and multilevel amplitude quantization for low-distortion audio reproduction. A stereo DAC is a semiconductor that converts digital audio samples into left and right analog voltage signals. It belongs to the digital-to-analog converter and audio signal-conversion hierarchy, where it bridges digital audio sources, such as decoders, receivers, and digital audio processors, with analog line-level amplification, mixing, recording, or loudspeaker-driver circuits. The PCM1773 family integrates the converter core and line-out circuitry to reduce external analog signal-path complexity. The PCM1773PW supports 24-bit digital audio data and sampling rates up to 50 kSPS, as identified by the manufacturer product page and distributor records. Its 98 dB signal-to-noise ratio is a principal performance figure for evaluating quiet stereo output. Hardware control provides a straightforward way to manage the line-output operating mode, while the integrated line-out amplifier simplifies connections to downstream analog audio circuitry. Texas Instruments describes the data converters as CMOS monolithic integrated circuits using an enhanced multilevel architecture. This architecture combines noise shaping with multilevel amplitude quantization to improve dynamic performance and reduce quantization-related distortion. The PCM1773PW package is a 16-pin TSSOP, designated PW by Texas Instruments, making it suitable for compact consumer and industrial audio equipment where conventional surface-mount assembly is preferred. Typical uses include stereo audio decoding, digital television and set-top-box audio paths, multimedia equipment, portable consumer electronics, and other systems requiring a two-channel audio DAC. Designers can use the integrated line-out stage to reduce the number of external analog components, although the actual output topology, gain, loading, and bypass configuration must follow the manufacturer application guidance. PCB implementation should preserve short, low-noise analog connections and route digital audio signals away from sensitive output nodes. Input and output decoupling, grounding, exposed analog sections, and the treatment of digital supply returns should follow the manufacturer datasheet layout and component recommendations. Because audio converters can reproduce digital-source noise and distortion directly, the complete power, clock, and source-chain design affects the final listening result. This product page consolidates the manufacturer specifications, package information, source links, and application guidance for PCM1773PW into an engineering-focused reference. It also distinguishes the target device from family-related choices, identifies where additional technical details are required, and provides selection criteria for stereo DAC and line-out designs.
PCM1773RGA - 24-Bit Stereo Audio DAC | Texas Instruments
The Texas Instruments PCM1773RGA is a low-voltage, low-power stereo audio digital-to-analog converter with an integrated line-out amplifier and hardware control. It supports two-channel, 24-bit audio at up to 50 kHz through an I2S interface, provides 98 dB signal-to-noise ratio, and is packaged in a 20-pin VQFN (RGA) measuring 4.2 mm by 4.2 mm. Its combination of a delta-sigma DAC, integrated line output stage, and compact surface-mount package makes it suitable for compact audio systems. A stereo audio DAC converts digital PCM samples into left- and right-channel analog voltages. The PCM1773RGA integrates that conversion function with line-out circuitry, reducing the number of external components required in typical audio signal paths. An I2S-compatible digital interface connects the converter to an audio processor, decoder, or digital audio source, while the integrated line-output stage provides an analog output suitable for subsequent voltage amplification or line-level routing. The principal performance characteristics are 24-bit conversion resolution, 50 kHz maximum sampling performance, 98 dB SNR, and support for two audio channels. The manufacturer identifies the device as a low-voltage, low-power stereo DAC with hardware line-output control. Those characteristics place it between basic digital audio interfaces and higher-performance integrated audio converter families, where channel count, converter resolution, output topology, and control requirements determine the appropriate replacement path. The PCM1773 family uses CMOS integrated circuitry containing stereo digital-to-analog converters, line-out circuitry, and support functions. In this configuration, the digital interface receives serial audio data while the converter reconstructs the analog waveform. The integrated line-output amplifier provides a more direct connection to the next analog stage than a bare converter output, although the exact output configuration, load capability, and gain settings must be confirmed against the manufacturer datasheet before finalizing a board design. Typical uses include compact stereo audio playback, digital receiver and decoder designs, audio-interface modules, multimedia systems, and line-level analog output stages. The 24-bit interface is suitable for preserving source word depth, while the 98 dB SNR specification provides a clear dynamic-range figure for architecture selection. The 50 kHz sampling limit should be checked against the required source rate; designs operating at higher rates need a different converter family. PCB planning should place the digital interface, analog outputs, bypass capacitors, and exposed thermal pad according to the manufacturer layout guidance. Maintain the required supply voltage, grounding, and output-load conditions, and account for the exposed pad when defining copper area and thermal relief. Do not assume that a same-package family member is interchangeable without verifying pin functions, control polarity, output configuration, and timing requirements. This product page consolidates the known 24-bit, two-channel, 50 kHz, 98 dB SNR, I2S, line-out, and VQFN-20 characteristics with practical integration guidance. It also distinguishes documented device facts from engineering details that still require confirmation from the manufacturer datasheet, helping designers move from part selection to a controlled schematic and layout review.
PCM1781DBQ - 24-Bit Stereo Audio DAC | Texas Instruments
The Texas Instruments PCM1781DBQ is a 24-bit stereo audio digital-to-analog converter with typical 192 kHz sampling and support for sampling rates up to 200 kHz, 106 dB signal-to-noise ratio, and a 16-lead SSOP package. It accepts industry-standard digital audio data and uses hardware control pins for configuration. An audio DAC is a digital-to-analog converter, a member of the broader signal-conversion and data-converter hierarchy. It reconstructs continuous analog audio from sampled digital data. The PCM1781 combines two converter channels with support circuitry in a monolithic CMOS integrated circuit, making it suitable for stereo sound cards, active speakers, digital mixers, consumer audio equipment, and embedded audio systems. Key performance characteristics include 24-bit resolution, 106 dB typical SNR at a 5 V supply, and 0.002% typical THD+N. The converter accepts standard audio formats through its serial interface, while four hardware control pins provide a simplified configuration method. These characteristics are important for reducing quantization noise and maintaining low distortion in high-fidelity audio paths. The device uses an enhanced multilevel delta-sigma architecture. This architecture improves dynamic performance and provides better tolerance to clock jitter than conventional delta-sigma converters. Texas Instruments identifies the PCM1780, PCM1781, and PCM1782 as a related CMOS family with different control-interface feature sets, allowing engineers to select the converter that matches their system architecture without changing the basic 16-lead SSOP footprint. Typical applications include professional and consumer stereo audio equipment, powered speaker systems, digital mixing consoles, automotive infotainment systems, and audio interfaces requiring two analog outputs. The 16-lead SSOP package supports compact, surface-mount PCB layouts, although analog and digital return paths still require careful layout discipline. For reliable performance, use the application circuit recommended by the manufacturer for supply decoupling, reference-voltage treatment, and analog output filtering. Keep the digital clock and data traces away from the analog outputs, provide adequate output-stage drive for the intended load, and verify headroom, filtering, and timing against the device data sheet before releasing a production design. This product page combines the manufacturer specifications with practical selection guidance, interface analysis, drop-in family comparisons, application notes, and PCB design considerations. It focuses on the engineering distinctions that determine whether the PCM1781DBQ is suitable for a stereo audio conversion design.
PCM1782DBQ - 24-Bit Stereo Audio DAC | Texas Instruments
Texas Instruments PCM1782DBQ is a 24-bit stereo audio digital-to-analog converter with a nominal 192 kHz sampling rate, support for sampling rates up to 200 kHz, and an I2S interface in a 16-lead SSOP package. The converter uses TI's enhanced multilevel delta-sigma architecture, which combines high-resolution audio conversion with improved tolerance to clock jitter. It also includes programmable functions accessed through a three-wire serial control port. An audio DAC is a data-converter IC that transforms digital audio samples into left and right analog voltage signals for subsequent amplification and loudspeaker or headphone drive. In the broader hierarchy, the PCM1782DBQ belongs to the digital-to-analog converter class, within interface and signal-conversion ICs, and ultimately within semiconductor devices used in professional and consumer audio systems. The principal specifications of the PCM1782DBQ include 24-bit resolution, a 192 kHz sampling-rate designation, support for I2S audio data, and a 16-lead SSOP package. According to the Texas Instruments product page, the PCM1780, PCM1781, and PCM1782 share the same CMOS monolithic converter family and use enhanced multilevel delta-sigma conversion. The PCM1782 provides the complete set of user-programmable functions through its three-wire serial control port. The delta-sigma architecture performs digital noise shaping before converting the filtered digital stream into an analog output. Its multilevel implementation is intended to improve dynamic performance and reduce sensitivity to timing variation in the incoming clock. For system design, this makes the device appropriate when a compact stereo conversion stage is required without moving to a larger multichannel audio-converter package. Exact analog performance values and operating limits should be confirmed from the manufacturer datasheet for the selected production configuration. Typical applications include digital mixing consoles, professional audio interfaces, stereo monitor controllers, broadcast equipment, digital instruments, and high-fidelity playback systems. In these systems, the PCM1782DBQ can accept digital audio from a transport or audio processor and provide separate analog outputs for left and right channels. The three-wire control interface permits configuration of supported device functions when the host system includes the appropriate register-control sequence. A key implementation consideration is the relationship between the master clock, serial audio clock, and data timing. The converter must receive correctly timed I2S data, and the PCB should keep clock and data routing short and away from noisy switching nodes. Analog output filtering and grounding should follow the reference circuitry in the manufacturer datasheet, because incorrect filter implementation can affect channel balance and audible noise performance. This product page combines the exact PCM1782DBQ family identification, practical interface guidance, family-level alternatives, and design-focused comparisons. It helps engineers evaluate clocking, control, package, and replacement considerations before beginning an audio-converter design.
PCM1782DBQR - 24-Bit Stereo Audio DAC | Texas Instruments (Tape & Reel)
Texas Instruments PCM1782DBQR is a 24-bit stereo audio digital-to-analog converter with a nominal 192 kHz sampling rate, support for sampling rates up to 200 kHz, and an I2S interface in a 16-lead SSOP package. The converter uses TI's enhanced multilevel delta-sigma architecture, which combines high-resolution audio conversion with improved tolerance to clock jitter. It also includes programmable functions accessed through a three-wire serial control port. An audio DAC is a data-converter IC that transforms digital audio samples into left and right analog voltage signals for subsequent amplification and loudspeaker or headphone drive. In the broader hierarchy, the PCM1782DBQR belongs to the digital-to-analog converter class, within interface and signal-conversion ICs, and ultimately within semiconductor devices used in professional and consumer audio systems. The principal specifications of the PCM1782DBQR include 24-bit resolution, a 192 kHz sampling-rate designation, support for I2S audio data, and a 16-lead SSOP package. According to the Texas Instruments product page, the PCM1780, PCM1781, and PCM1782 share the same CMOS monolithic converter family and use enhanced multilevel delta-sigma conversion. The PCM1782 provides the complete set of user-programmable functions through its three-wire serial control port. The delta-sigma architecture performs digital noise shaping before converting the filtered digital stream into an analog output. Its multilevel implementation is intended to improve dynamic performance and reduce sensitivity to timing variation in the incoming clock. For system design, this makes the device appropriate when a compact stereo conversion stage is required without moving to a larger multichannel audio-converter package. Exact analog performance values and operating limits should be confirmed from the manufacturer datasheet for the selected production configuration. Typical applications include digital mixing consoles, professional audio interfaces, stereo monitor controllers, broadcast equipment, digital instruments, and high-fidelity playback systems. In these systems, the PCM1782DBQR can accept digital audio from a transport or audio processor and provide separate analog outputs for left and right channels. The three-wire control interface permits configuration of supported device functions when the host system includes the appropriate register-control sequence. A key implementation consideration is the relationship between the master clock, serial audio clock, and data timing. The converter must receive correctly timed I2S data, and the PCB should keep clock and data routing short and away from noisy switching nodes. Analog output filtering and grounding should follow the reference circuitry in the manufacturer datasheet, because incorrect filter implementation can affect channel balance and audible noise performance. This product page combines the exact PCM1782DBQR family identification, practical interface guidance, family-level alternatives, and design-focused comparisons. It helps engineers evaluate clocking, control, package, and replacement considerations before beginning an audio-converter design.
PCM1789PW - 24-Bit 192kHz Stereo Audio DAC | Texas Instruments
Texas Instruments PCM1789PW is a 24-bit stereo audio digital-to-analog converter with differential outputs, a maximum sampling rate of 192 kSPS, and a 113 dB SNR rating. It operates from a 4.5 V to 5.5 V supply and is packaged in a 24-pin TSSOP. The device supports I2S audio data in addition to software-controlled I2C and SPI-compatible configuration interfaces. A stereo audio DAC is a signal-conversion integrated circuit that accepts digital audio samples and produces analog voltage signals suitable for audio output stages. Within the product hierarchy, PCM1789PW is a delta-sigma audio DAC, a data-converter IC, and a semiconductor for consumer, professional, and industrial audio equipment. Its differential outputs can reduce sensitivity to common-mode noise when paired with a suitable analog output network and amplifier stage. Principal features include 24-bit resolution, 192 kSPS sampling, 113 dB signal-to-noise ratio, stereo differential outputs, and a 4.5 V to 5.5 V analog and digital supply range. The PCM1789 supports software-mode control through three-wire SPI-compatible or two-wire I2C-compatible serial interfaces, enabling access to digital attenuation, soft mute, de-emphasis, and other device functions. A hardware-control mode also provides two user-programmable functions through control pins. The converter uses a multi-level delta-sigma architecture to reconstruct analog audio from pulse-code-modulated digital samples. The 24-bit data width supports fine amplitude quantization, while the 192 kSPS ceiling accommodates high-resolution PCM streams and oversampled source material. Differential stereo outputs provide two complementary analog channels for balanced downstream audio paths. Exact filter behavior, clock requirements, and output-stage implementation should be confirmed in the manufacturer datasheet. Typical applications include high-resolution digital audio players, professional audio interfaces, home-theater equipment, active speakers, and instrumentation requiring stereo conversion. The I2S-compatible digital input suits audio processors, USB interface controllers, and digital transport devices, while I2C or SPI configuration is useful where a host controller needs software setup and attenuation adjustment. A key implementation consideration is analog-output filtering. Follow the manufacturer reference circuit and preserve the required supply decoupling, clock routing, and output-load arrangement. Because output loading and external filter topology can alter distortion and dynamic range, validate the complete channel rather than relying only on the converter's headline SNR specification. This page organizes the official device description, interface capabilities, package information, sourcing questions, and engineering constraints into one implementation-oriented reference. It also identifies the limits of drop-in replacement sourcing: no five distinct pin-to-pin alternatives were confirmed, and a packaging-only orderable suffix is not presented as a meaningful engineering alternative.
PCM1789PWR - 24-Bit 192kHz Stereo DAC | Texas Instruments
The Texas Instruments PCM1789PWR is a high-performance, 24-bit stereo audio digital-to-analog converter with differential outputs, supported sampling rates from 8 kHz to 192 kHz, and a 113 dB SNR rating. The device is packaged in a 24-pin TSSOP (PW) surface-mount package. Its enhanced multi-level delta-sigma architecture supports 16-, 20-, 24-, and 32-bit digital audio input words through a flexible serial audio interface. An audio digital-to-analog converter, or audio DAC, converts digital PCM samples into analog voltage signals suitable for headphone, line-level, or power-amplifier inputs. Within the signal-chain hierarchy, the PCM1789 is an audio DAC, a data-converter IC, and a signal-conversion device used between a digital audio source and an analog output stage. Differential outputs can support balanced analog connections while reducing sensitivity to ground-borne noise. Key features include software-programmable digital attenuation, soft mute, de-emphasis, and user-programmable hardware control functions. The control architecture supports three-wire SPI-compatible and two-wire I2C-compatible serial interfaces, while the audio data interface supports I2S-format operation. These features allow the converter to be configured for attenuation levels, mute behavior, and system operating modes without requiring a separate external control controller for every adjustment. The enhanced multi-level delta-sigma modulator is designed for high-resolution playback while supporting a broad range of sample rates. Differential analog outputs provide two audio channels, and the available interface options make the device suitable for systems using either serial control buses or discrete hardware-control lines. The reported 113 dB SNR makes the PCM1789 relevant to high-fidelity audio equipment where dynamic-range margin is important. Typical applications include premium CD and DVD player audio paths, digital broadcast receivers, professional audio mixers, sampling-rate converters, home-theater receivers, and high-end portable audio equipment. Its 192 kHz capability also supports high-resolution source material, although system clocking and output reconstruction must be designed to preserve the converter's full performance. For PCB design, keep the analog output routing short, place decoupling capacitors near the supply pins, and follow the manufacturer pin-description table when assigning connector and control-signal routing. Differential outputs should be routed with matched geometry where practical, and the exposed digital signals should remain separated from sensitive analog output paths to minimize crosstalk.
PCM1791ADBR - 24-Bit Stereo Audio DAC | Texas Instruments
The Texas Instruments PCM1791ADBR is a 24-bit stereo digital-to-analog converter with a 192 kHz sampling rate, 113 dB typical dynamic range, and balanced differential outputs in a 28-lead SSOP package. It uses TI’s segment DAC architecture to provide excellent dynamic performance and improved tolerance to clock jitter. The device also includes programmable gain, digital filtering, and a serial PCM interface suitable for high-quality audio signal chains. An audio DAC is a mixed-signal integrated circuit that converts digital PCM audio samples into analog voltage signals for amplification and reproduction. Within the broader semiconductor hierarchy, the PCM1791ADBR belongs to the DAC family, which is part of data converters and analog mixed-signal ICs. Its balanced outputs can simplify the connection between the converter and a subsequent analog amplifier while reducing common-mode noise in a carefully designed audio system. The converter’s principal performance figures include 24-bit resolution, 192 kHz sampling capability, 113 dB typical dynamic range, 113 dB typical signal-to-noise ratio, and 0.001% typical total harmonic distortion plus noise. The manufacturer describes a 2.1 V RMS full-scale differential output at the post amplifier. Programmable gain and digital filtering provide additional control for matching the converter to different downstream amplifier and analog-output arrangements. PCM1791ADBR is a monolithic CMOS device implementing TI’s advanced segment DAC architecture. This architecture is designed to achieve strong dynamic performance and better immunity to sampling-clock jitter than many conventional converter implementations. The PCM interface and internal support circuitry are integrated into one package, reducing the number of discrete components required for a stereo conversion path. Its balanced voltage outputs also permit either balanced downstream amplification or conversion to an unbalanced output where appropriate. Typical applications include high-resolution CD and DVD audio conversion, professional audio equipment, digital mixing consoles, multichannel home-theater systems, active loudspeakers, and other consumer audio products that require simultaneous left- and right-channel conversion. The device can also serve as the DAC stage in a digital playback system feeding line-level amplifiers. Clock and interface implementation remain important because jitter, grounding, and output filtering influence the final analog performance. For a new layout, place the digital interface and analog supply connections according to the manufacturer’s recommended schematic and pin description. Keep sensitive analog output routing compact, maintain a quiet ground reference, and account for the package’s 28-lead SSOP footprint. The balanced output topology is an advantage, but the downstream amplifier must support the selected signal arrangement to realize its full benefit. This product page consolidates the manufacturer’s architecture information, distributor listing details, verified performance figures, drop-in alternatives, and application guidance. It also provides a package-aware comparison and practical design notes so engineers can assess the PCM1791ADBR against other stereo DAC options without relying on a basic catalog summary alone.
PCM1792ADB - 24-Bit 192kHz Stereo DAC | Texas Instruments
Texas Instruments PCM1792ADB is a 24-bit stereo digital-to-analog converter with support for 192 kHz sampling and differential current outputs, housed in a 28-pin SSOP (DB) package. It uses the manufacturer’s advanced-segment DAC architecture and is designed for high-performance digital audio equipment. The device operates from dual analog supplies, supports digital audio interfaces, and includes digital filtering for professional and audiophile signal chains. A DAC is a digital-to-analog converter, a signal-conversion IC that transforms digital audio samples into a continuous analog voltage or current representation. Within the signal-chain hierarchy, the PCM1792ADB belongs to the audio converter family, connects digital source equipment to an analog output stage, and operates as part of a broader audio signal-processing system. Its balanced current outputs allow designers to optimize analog gain, noise behavior, and channel matching in the subsequent circuitry. Key performance figures include 24-bit resolution, a maximum sampling rate of 192 kHz, a differential output current of 7.8 mA peak-to-peak, and a dynamic range of 132 dB for mono operation at 9 V rms. Stereo dynamic range reaches 129 dB at 4.5 V rms and 127 dB at 2 V rms. Total harmonic distortion plus noise is specified at 0.0004%, making the converter suitable for demanding audio playback, studio monitoring, digital mixing, and multichannel audio systems. The advanced-segment DAC architecture is designed to provide strong dynamic performance and improved tolerance to clock jitter. Digital filtering is part of the conversion path, while the balanced differential outputs support low-noise analog design. Because the device produces current rather than a direct voltage output, an external operational-amplifier or current-to-voltage stage is normally required to establish the final analog output voltage and accommodate the desired channel gain. Typical applications include professional digital mixers, high-resolution CD and DVD player analog stages, audio DAC products, studio monitors, and digital recording equipment. The converter is also appropriate for consumer and industrial systems requiring 24-bit playback through 192 kHz. In these systems, the PCM1792ADB handles the conversion stage while external circuitry performs current-to-voltage conversion, analog filtering, gain setting, and output isolation. The main design consideration is supply planning. The device uses dual analog supplies, and its specified dynamic range changes with operating voltage: 132 dB at 9 V rms mono, 129 dB at 4.5 V rms stereo, and 127 dB at 2 V rms stereo. Board layout should keep digital-clock and data traces away from sensitive analog output paths, while the analog output stage must preserve the converter’s balanced symmetry. This product page combines the manufacturer’s core architecture information, exact PCM1792ADB orderable identifiers, package details, operating limits, application guidance, and same-package family comparisons. It also identifies where engineering data such as the complete pin description, electrical characteristic curves, and recommended external circuits must be taken directly from the manufacturer datasheet.
PCM1792ADBR - 24-Bit 192kHz Stereo DAC | Texas Instruments (Tape & Reel)
Texas Instruments PCM1792ADBR is a 24-bit stereo digital-to-analog converter with support for 192 kHz sampling and differential current outputs, housed in a 28-pin SSOP (DB) package. It uses the manufacturer’s advanced-segment DAC architecture and is designed for high-performance digital audio equipment. The device operates from dual analog supplies, supports digital audio interfaces, and includes digital filtering for professional and audiophile signal chains. A DAC is a digital-to-analog converter, a signal-conversion IC that transforms digital audio samples into a continuous analog voltage or current representation. Within the signal-chain hierarchy, the PCM1792ADBR belongs to the audio converter family, connects digital source equipment to an analog output stage, and operates as part of a broader audio signal-processing system. Its balanced current outputs allow designers to optimize analog gain, noise behavior, and channel matching in the subsequent circuitry. Key performance figures include 24-bit resolution, a maximum sampling rate of 192 kHz, a differential output current of 7.8 mA peak-to-peak, and a dynamic range of 132 dB for mono operation at 9 V rms. Stereo dynamic range reaches 129 dB at 4.5 V rms and 127 dB at 2 V rms. Total harmonic distortion plus noise is specified at 0.0004%, making the converter suitable for demanding audio playback, studio monitoring, digital mixing, and multichannel audio systems. The advanced-segment DAC architecture is designed to provide strong dynamic performance and improved tolerance to clock jitter. Digital filtering is part of the conversion path, while the balanced differential outputs support low-noise analog design. Because the device produces current rather than a direct voltage output, an external operational-amplifier or current-to-voltage stage is normally required to establish the final analog output voltage and accommodate the desired channel gain. Typical applications include professional digital mixers, high-resolution CD and DVD player analog stages, audio DAC products, studio monitors, and digital recording equipment. The converter is also appropriate for consumer and industrial systems requiring 24-bit playback through 192 kHz. In these systems, the PCM1792ADBR handles the conversion stage while external circuitry performs current-to-voltage conversion, analog filtering, gain setting, and output isolation. The main design consideration is supply planning. The device uses dual analog supplies, and its specified dynamic range changes with operating voltage: 132 dB at 9 V rms mono, 129 dB at 4.5 V rms stereo, and 127 dB at 2 V rms stereo. Board layout should keep digital-clock and data traces away from sensitive analog output paths, while the analog output stage must preserve the converter’s balanced symmetry. This product page combines the manufacturer’s core architecture information, exact PCM1792ADBR orderable identifiers, package details, operating limits, application guidance, and same-package family comparisons. It also identifies where engineering data such as the complete pin description, electrical characteristic curves, and recommended external circuits must be taken directly from the manufacturer datasheet.
PCM1792DB - 24-Bit 192kHz Stereo DAC | Texas Instruments
Texas Instruments PCM1792DB is a 24-bit stereo digital-to-analog converter supporting 192 kHz PCM sampling and 200 kHz DSD operation, housed in a 28-lead SSOP package. It uses advanced segment DAC architecture, balanced differential current outputs, and a serial control interface for programmable audio operation. The converter is designed for high-fidelity audio systems requiring low distortion and high dynamic range. An audio DAC converts digital PCM or DSD data into analog voltage or current signals suitable for amplification and loudspeaker drive. Within the signal chain, it sits between a digital audio source and an analog output stage. The PCM1792DB combines two converter channels and associated support circuitry in one monolithic CMOS device, simplifying stereo audio designs while preserving independent balanced outputs. The PCM1792DB provides a dynamic range of 132 dB for mono operation at 9 Vrms and 129 dB for stereo operation at 4.5 Vrms. Its THD+N is 0.0004%, and its differential current output reaches 7.8 mA peak-to-peak. These characteristics make the converter appropriate for premium digital audio equipment, professional monitoring, USB and network audio products, and other systems where low-level analog distortion can affect sound quality. Advanced segment DAC architecture is the core technical feature of this converter. According to the manufacturer datasheet, the architecture improves dynamic performance and tolerance to clock jitter. The device uses an 8-times oversampling digital filter, balanced current outputs that allow output topology optimization, and a serial control interface for mode configuration. These functions support integration into designs requiring both PCM playback and Direct Stream Digital operation. Typical applications include high-resolution stereo DAC equipment, professional audio monitors, digital mixing consoles, USB audio interfaces, and home-theater signal processing. The differential outputs are particularly useful when the downstream amplifier or current-voltage conversion stage can preserve the benefits of balanced operation. System designers must account for the required analog supplies, output load, external conversion network, and clocking arrangement when laying out the PCB. A critical implementation consideration is maintaining clean, low-noise analog and digital supply rails. Place the bypass capacitors specified by the manufacturer close to their corresponding power pins, route high-current outputs away from sensitive digital and analog inputs, and use a symmetric ground strategy around the converter outputs. The 28-lead SSOP footprint also requires careful soldering practices because its lead pitch is relatively narrow. This page consolidates the PCM1792DB electrical characteristics, package details, application guidance, and replacement considerations into an engineering-focused reference. It also distinguishes true drop-in interchangeability from related converters and identifies the design variables that most often determine success in a high-performance audio DAC implementation.
PCM1792DBR - 24-Bit 192kHz Stereo DAC | Texas Instruments
Texas Instruments PCM1792DBR is a 24-bit, 192kHz stereo digital-to-analog converter using advanced segment DAC architecture, with differential current outputs and a 28-lead SSOP package. Its headline performance includes a dynamic range of 132dB for mono operation at 9Vrms, 129dB for stereo operation at 4.5Vrms, and 127dB for stereo operation at 2Vrms. The converter also specifies THD+N of 0.0004% and differential output current of 7.8mA peak-to-peak. An audio DAC is a semiconductor that converts digital PCM audio samples into an analog voltage or current signal. The PCM1792 belongs to the broader digital-to-analog converter category, where it sits between a digital audio interface and an analog output stage. Balanced differential current outputs provide a useful starting point for low-noise audio signal chains because they can be converted to single-ended voltage through an external current-to-voltage network. The principal features are high-resolution conversion, operation at up to 192kHz, and the segment DAC architecture. According to the Texas Instruments PCM1792 product page, the device includes support circuitry in a compact 28-lead SSOP package. Its differential outputs allow the output topology to be optimized for the intended analog stage, while the specified dynamic range and THD+N figures support high-fidelity audio equipment. Clock jitter tolerance is another important aspect of the PCM1792 architecture. Texas Instruments describes the converter as using advanced segment DAC architecture to achieve strong dynamic performance and improved tolerance to clock jitter. In practice, that makes the device suitable for systems in which the digital audio clock and data paths require careful implementation to preserve the converter’s low-distortion performance. Typical uses include CD and DVD player digital-to-analog sections, professional audio equipment, home-theater receivers, digital mixing consoles, and other stereo audio products. The 24-bit, 192kHz conversion capability accommodates high-resolution source material, while the balanced current-output architecture is especially suitable for designs that require flexible analog filtering and gain staging. When designing around the PCM1792DBR, follow the manufacturer datasheet for the external clock, digital interface, output network, filtering, power-supply, and grounding configuration. Correct implementation of the output current-to-voltage conversion and the required bypass capacitors is fundamental to preserving the specified dynamic range and distortion performance. This page organizes the PCM1792DBR’s key specifications, practical application fit, package information, comparison parameters, and engineering guidance into a design-focused reference for engineers evaluating stereo DAC implementations.
PCM1793DB - 24-Bit 192kHz Stereo DAC | Texas Instruments
Texas Instruments PCM1793DB is a 24-bit, 192 kHz sampling stereo digital-to-analog converter with balanced voltage outputs and hardware control, packaged in a 28-lead SSOP. The monolithic CMOS device combines two converter channels and support circuitry, while its advanced segment DAC architecture provides excellent dynamic performance and improved tolerance to clock jitter. Typical signal-to-noise ratio is 113 dB, typical total harmonic distortion plus noise is 0.001%, and typical full-scale output is 2.1 V rms at the postamplifier. A digital-to-analog converter, or DAC, converts digital audio samples into an analog voltage waveform. The PCM1793 belongs to the broader hierarchy of stereo DAC, audio converter, signal-conversion IC, and semiconductor. Balanced voltage outputs support noise-rejecting analog signal paths, allowing a designer to optimize the output stage for the target amplifier and load. Its I2S-compatible digital interface accepts audio data from a digital audio source, while the DAC performs the final conversion before the analog output stage. The principal features are 24-bit resolution, a maximum sampling rate of 192 kHz, balanced outputs, 113 dB dynamic range, and a typical THD+N of 0.001%. Hardware control provides an external interface for adjusting supported operating functions without relying entirely on software commands. The advanced segment DAC architecture is specifically designed to improve dynamic performance and reduce sensitivity to timing variations in the incoming digital clock. The converter uses a monolithic CMOS implementation containing stereo digital-to-analog converters and associated support circuitry. Balanced voltage outputs distinguish the PCM1793 from converters that provide differential current outputs. At the postamplifier, a typical full-scale output of 2.1 V rms provides a defined analog reference level for subsequent voltage amplification or line-level routing. Its operating supply range is 4.5 V to 5.5 V. Typical applications include high-resolution stereo audio equipment, CD and DVD player digital audio paths, professional audio converters, powered speakers, headphone-amplifier front ends, and digital audio system boards. The balanced output topology is useful when the downstream circuitry supports balanced inputs, while a carefully designed single-ended summing network can serve conventional line outputs. Designers should treat the power supply, digital clock, ground layout, and output network as a complete signal-chain design. Place decoupling and output-network components close to their associated pins, keep analog return paths separate from switching and digital return currents, and provide filtering appropriate to the audio bandwidth. The SSOP package also requires attention to solder-joint quality and thermal conditions during assembly. This product overview combines converter architecture, key electrical characteristics, application guidance, package information, and sourcing-oriented details. It is intended to help engineers determine whether the PCM1793DB's balanced voltage output, dynamic performance, and interface characteristics fit a stereo DAC design before beginning a detailed schematic and layout review.
PCM1793DBR - 24-Bit 192kHz Stereo DAC | Texas Instruments
Texas Instruments PCM1793DBR is a 24-bit, 192 kHz stereo digital-to-analog converter with a 113 dB dynamic range, 113 dB SNR, and 0.001% typical THD+N, housed in a 28-lead SSOP package. The converter uses balanced differential voltage outputs and a three-wire serial audio interface for high-resolution digital-to-analog conversion. An audio DAC is an interface IC that converts digital audio samples into analog voltage signals suitable for amplifiers, headphones, line outputs, and audio conversion equipment. The PCM1793 belongs to the DAC hierarchy within analog and mixed-signal semiconductors, combining a stereo DAC core, digital filtering, clock-jitter tolerance, and output circuitry in one monolithic CMOS device. Its segment DAC architecture separates the current-steering operation into smaller segments, improving linearity and dynamic performance. Principal features include advanced segment DAC architecture, balanced outputs, 24-bit resolution, sampling rates up to 192 kHz, and improved tolerance to clock jitter. According to the manufacturer datasheet, analog performance is measured at the PCM1793 output using an Audio Precision System Two Cascade system with a 20 kHz AES17 measurement filter. The specified 113 dB dynamic range and 113 dB SNR support demanding consumer and professional audio paths. The PCM1793 is a monolithic CMOS integrated circuit containing two stereo converter channels and their support circuitry. Its differential outputs provide a balanced signal path that can optimize analog output implementation and reduce common-mode effects in downstream circuitry. A typical full-scale differential output is 2.1 V rms at the postamplifier, while the digital side accepts serial audio data through a three-wire interface. Typical applications include high-resolution digital audio players, professional audio interfaces, USB and network audio equipment, home-theater receivers, and digital mixing consoles. It is also suitable for portable listening equipment when board area, power consumption, and balanced-output integration are important. The 28-lead SSOP package simplifies assembly in designs that already use surface-mount audio converters. When laying out a PCM1793 board, place decoupling capacitors close to the analog and digital supply pins, route audio data and clock signals away from analog outputs, and provide a clean return path for the balanced outputs. Verify the external clock, serial-data timing, digital-filter configuration, and output circuitry against the manufacturer application guidance before production. This page combines the PCM1793 technical specifications with practical application guidance, same-family drop-in candidates, a parameter comparison, and PCB-oriented design notes. These engineering resources help shorten component selection and support a deliberate transition from the 28-lead SSOP datasheet specification to a complete stereo DAC implementation.
PCM1794DB - 24-Bit 192kHz Stereo DAC | Texas Instruments
The Texas Instruments PCM1794DB is a 24-bit stereo digital-to-analog converter supporting sampling rates up to 192 kHz. It uses advanced segment DAC architecture, includes support circuitry, and is packaged in a 28-lead SSOP. The converter provides balanced current outputs, allowing the analog output stage to be optimized for either differential or single-ended signal-chain architectures. A digital-to-analog converter, or DAC, converts digital audio samples into an analog voltage or current representation. The PCM1794DB belongs to the stereo audio DAC category within the broader ADC/DAC and interface-converter hierarchy. It is designed for high-resolution audio equipment, where digital source quality must be translated into a low-distortion analog output for headphone, line, or preamplifier stages. Key features include 24-bit data resolution, 192 kHz maximum sampling capability, advanced segment DAC architecture, balanced current outputs, and support for common digital audio interfaces including I2S, PCM, and left-justified formats. The manufacturer describes the converter as a monolithic CMOS integrated circuit with improved tolerance to clock jitter. Its balanced outputs support flexible analog signal routing while preserving channel symmetry. The PCM1794DB is normally used with external current-to-voltage conversion, filtering, and output-buffer circuitry. The balanced output architecture can reduce even-order distortion and common-mode effects when paired with a suitably matched analog stage. The converter also includes digital control functions for reset and operating-mode configuration, allowing it to be coordinated with an audio system clock and source device. Typical applications include high-resolution stereo DAC modules, USB and network audio converters, CD-quality playback equipment, digital mixing consoles, headphone amplifiers, and balanced line-output stages. The 192 kHz sampling capability makes it appropriate for studio monitoring and archival audio systems, although system clocking and analog implementation remain important to achieving the intended performance. When laying out a PCM1794DB circuit, keep digital clock and data traces away from the sensitive analog output network, use short and properly terminated clock routes, and place filtering and I/V components close to their associated pins. Verify power sequencing, reset timing, and the required 1024 system-clock initialization period before enabling normal audio operation. This product page consolidates the manufacturer device information, distributor identification, package details, and practical implementation guidance for engineers evaluating the PCM1794DB in a new audio-converter design.