ADC/DAC
بەرهەمەکان (3,600+)
AD5934YRSZ - 250 kSPS 12-Bit Impedance Converter | Analog Devices
The Analog Devices AD5934YRSZ is a 250 kSPS, 12-bit impedance converter and network analyzer that combines an on-board frequency generator with a 12-bit, 250 kSPS analog-to-digital converter (ADC). Housed in a 16-pin SSOP package (YRS suffix), the device is specified for operation from a 3.3 V supply with an external MCLK up to 16.776 MHz, and it produces an excitation output up to 50 kHz for sweeping an unknown complex impedance. The integrated discrete Fourier transform (DFT) engine returns calibrated real and imaginary 16-bit words per frequency point, allowing a host microcontroller to compute magnitude and phase. An impedance analyzer is an instrument class that measures the complex impedance (resistance plus reactance) of a component, sensor, or biological sample across a range of AC frequencies. Within the broader instrumentation hierarchy, the AD5934 sits between a discrete lock-in amplifier and a full benchtop LCR meter: it removes the need for a separate function generator, digitizer, and FFT processor while still delivering calibrated magnitude/phase data over a user-selected frequency sweep. This integration is what makes it attractive for embedded electrochemical, bioimpedance, and material-sensing products. Key specifications include 12-bit ADC resolution at 250 kSPS, an excitation amplitude programmable in four steps from 0.2 V p-p to 2.0 V p-p, a programmable gain amplifier (PGA) with x1 or x5 settings, an I2C-compatible serial interface, and an operating temperature range of -40C to +125C. The on-chip temperature sensor (TA pin) and dedicated system clock input allow designers to add temperature compensation and reject mains-related clock jitter in the same BOM. Architecturally, the AD5934 separates the excitation DAC, the transimpedance front end (with external RFB), the sampling ADC, and the DSP DFT block, all clocked from a single MCLK reference. The result is a system whose accuracy is determined by the external calibration resistor (typically 200 kohm between RFB and VIN), the stability of the MCLK source, and the impedance range selected via the gain resistor - not by any factory trim step, which simplifies board bring-up. Typical applications include bioimpedance and skin-conductance analysis, electrochemical sensor interfaces, in-line material moisture meters, portable LCR-style probes, and multi-frequency material identification. Engineers choose the AD5934 when they need calibrated magnitude/phase data without the cost, size, or power budget of a bench instrument. When designing with the part, place the calibration resistor close to the RFB and VIN traces and drive MCLK from a low-jitter source; this is the single biggest determinant of sweep-to-sweep repeatability. This page synthesizes distributor pricing, qualified drop-in alternatives, and practical layout notes not collected in the standalone datasheet PDF.
AD5934YRSZ-REEL7 - 250kSPS 12-Bit Impedance Converter | ADI
The Analog Devices AD5934YRSZ-REEL7 is a high-precision 12-bit, 250 kSPS impedance converter and network analyzer system-on-chip that combines an on-board programmable frequency generator with a 12-bit analog-to-digital converter (ADC) and an on-chip DSP engine for discrete Fourier transform (DFT) processing, all integrated into a 16-pin SSOP package. The device excites an external complex impedance with a known frequency up to 50 kHz, samples the response signal, and returns calibrated real and imaginary impedance words via I²C/SPI serial interface, eliminating the need for external signal conditioning and reducing the BOM for portable bio-impedance and material analysis designs. An impedance converter network analyzer is a specialized data acquisition system that performs synchronous sine excitation, current-to-voltage conversion, and discrete Fourier transform (DFT) processing to extract magnitude and phase information from a connected unknown impedance. As a member of the impedance analyzer / LCR meter IC family, it sits at the intersection of the broader categories of direct digital synthesis (DDS), signal chain analog-to-digital converter (ADC), and embedded DSP, which together form a complete vector impedance measurement sub-system. The AD5934 in particular integrates DDS, transimpedance amplifier, ADC, and DFT engine into one IC. Key specifications include 12-bit ADC resolution, 250 kSPS sampling rate, programmable excitation output frequency up to 50 kHz, 16.776 MHz internal clock or external MCLK input, on-chip temperature sensor with ±2 °C precision, and serial interface compatibility with I²C or SPI protocols. The device supports a system clock from 0.1 MHz to 16.776 MHz and is supplied from a single 2.7 V to 5.5 V rail, equivalent to most 3 V or 5 V logic rails. The internal DDS allows 0.1 Hz frequency resolution when clocked from the on-chip oscillator. The excitation amplitude is programmable in four discrete steps between 0.2 Vpp and 1.98 Vpp to accommodate different impedance ranges. The AD5934 architecture combines a 28-bit direct digital synthesizer (DDS) core, a low-noise transimpedance front-end, a 12-bit successive-approximation ADC, and an embedded DFT processor that returns calibrated real (R) and imaginary (I) 16-bit words per frequency point. Gain factor calibration using a reference impedance removes system gain error across the 100 Ω to 10 MΩ measurement range, equivalent to a four-decade dynamic span, while the embedded temperature sensor compensates for system drift across the -40 °C to +125 °C automotive-grade operating range. The serial interface supports both standard I²C (100 kHz) and SPI (up to 5 MHz) for flexible host connectivity. Typical applications include portable bio-electrical impedance analysis (BIA) for body composition scales and fitness monitors, in-vitro electrochemical biosensors for glucose and pathogen detection, industrial material moisture and soil moisture analysis, fuel cell and battery impedance spectroscopy for state-of-charge estimation, and on-board diagnostic (OBD) systems for automotive sensor health monitoring. Compared to discrete lock-in amplifier solutions, the AD5934 reduces board area, BOM count, and firmware complexity by integrating the entire excitation-acquisition-DFT pipeline into one SSOP-16 package, while preserving calibration-grade accuracy through its gain factor compensation routine. When designing with the AD5934, place a precision 200 Ω or 100 kΩ reference resistor between the excitation output (IOUT) and the ADC input (VIN) for system calibration, and use the temperature sensor reading to correct for thermal drift of the reference resistor. The RFB pin selects the transimpedance gain; pair it with a low-temperature-coefficient external feedback resistor to extend the impedance measurement range beyond 1 MΩ. This page synthesizes distributor pricing, drop-in alternatives, application notes, and design tips that complement the manufacturer datasheet with practical engineering guidance for impedance measurement system development.
AD637JRZ - 0.25% RMS-to-DC Converter, 200kHz | Analog Devices
The Analog Devices AD637JRZ is a high-accuracy, wideband true RMS-to-DC converter that computes the true root mean square value of any complex waveform, delivering 0.25% conversion accuracy with a 200 kHz measurement bandwidth in a 16-lead SOIC package. An RMS-to-DC converter is a specialized analog computing IC that produces a DC output proportional to the root-mean-square (RMS) value of its input signal, regardless of waveform shape. Within the signal chain hierarchy, it sits between the analog front end and the ADC or metering stage, enabling true-RMS measurement of AC signals where simple average-responding circuits fail, such as for noise, distorted, or pulsed waveforms. Key features of the AD637JRZ include true RMS, mean-square, and absolute-value computation modes, a wide supply range of plus/minus 3V to plus/minus 18V, and a supply current of only 2.2 mA with power dissipation of approximately 108 mW. The device offers accuracy comparable to discrete and modular techniques, which historically cost far more and occupied more board area. Technically, the AD637 uses an implicit analog computation architecture based on a translinear multiplier-divider cell and an active low-pass filter/averaging stage. The J-grade device specified here guarantees 0.25% of reading accuracy, while the same die family is offered in A, B, and K grades with tighter error limits. The wide 200 kHz bandwidth supports measurement of audio, mains-harmonic, and medium-frequency signals. Typical applications include true-RMS panel meters and DMM front ends, RF and audio power measurement, industrial process monitoring of distorted waveforms from variable-frequency drives, and noise measurement instrumentation. Its low supply current also suits portable test equipment. Design consideration: the averaging capacitor on the external filter pin sets ripple and settling trade-offs; larger capacitance reduces output ripple but extends settling time, so choose it based on the lowest measurement frequency. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
AD650SD/883B - V/F & F/V Converter 1MHz | Analog Devices
The AD650SD/883B is a monolithic voltage-to-frequency (V/F) and frequency-to-voltage (F/V) converter from Analog Devices, designed for high-accuracy analog-to-digital conversion and precision frequency measurement. It operates at a maximum frequency of 1 MHz with a nonlinearity of ±0.1% (typical), making it suitable for demanding industrial and aerospace applications. The device is housed in a 14-pin ceramic dual-in-line package (CDIP) and is specified for the full military temperature range of -55°C to +125°C, ensuring reliable operation in extreme environments. A voltage-to-frequency converter (VFC) is an electronic circuit that converts an analog input voltage into a proportional output frequency. This type of converter is widely used in analog-to-digital conversion, where the frequency output can be easily counted by digital logic, providing high resolution and noise immunity. The AD650SD/883B also operates in the reverse mode as a frequency-to-voltage converter, enabling closed-loop control and frequency measurement applications. As a member of the voltage-to-frequency converter family, it bridges the analog and digital domains, offering a simple and robust interface for data acquisition systems. Key features of the AD650SD/883B include a 1 MHz full-scale frequency, ±0.1% typical nonlinearity, and a wide supply voltage range of ±9V to ±18V. The device offers both single-ended and differential input configurations, and its output is a square wave that can drive TTL or CMOS logic directly. The ceramic package provides excellent thermal stability and hermetic sealing, making it ideal for military and aerospace applications where reliability is critical. Technically, the AD650SD/883B uses a charge-balancing architecture that ensures high linearity and temperature stability. The input current is integrated over a fixed time period, and the output frequency is proportional to the input voltage. This design minimizes drift and provides excellent long-term stability. The device also includes an internal reference and a precision comparator, reducing the need for external components. Typical applications include precision analog-to-digital conversion, frequency-to-voltage conversion for tachometers and flow meters, and isolated signal transmission in industrial control systems. The AD650SD/883B is also used in aerospace telemetry and test instrumentation where high accuracy and wide temperature range are required. When designing with the AD650SD/883B, ensure proper decoupling of the power supply pins with 0.1µF ceramic capacitors placed close to the device. The input signal should be filtered to remove high-frequency noise, and the output frequency should be buffered if driving long cables. The device's power dissipation is moderate, but thermal management is recommended for high-temperature environments.
AD6600AST - 11-Bit, 20 MSPS Dual-Channel ADC | Analog Devices
The Analog Devices AD6600AST is an 11-bit, 20 MSPS dual-channel mixed-signal receiver ADC in a 44-LQFP package. It directly samples analog input frequencies up to 250 MHz and provides two receive channels, each with a 1 GHz input amplifier and 30 dB of automatic gain-ranging circuitry. The device supports 5 V analog operation and CMOS-compatible digital outputs for interfacing with 3.3 V or 5 V processing devices. A mixed-signal receiver ADC combines high-frequency analog sampling with parallel digital output. In the broader semiconductor hierarchy, the AD6600 belongs to the analog-to-digital converter family, integrates receiver functions into one device, and ultimately serves as a signal-chain interface for communications equipment. Its dual-channel architecture is designed for antenna-diversity receivers, where two antenna paths are sampled coherently for comparison and selection. Key features include 11-bit resolution, a 20 MSPS conversion rate, two analog inputs, a maximum 250 MHz analog input frequency, and 1 GHz input amplifiers. Each channel includes 30 dB of automatic gain ranging, which reduces the external signal-chain burden when received signal strength changes. Two's-complement CMOS output data can connect directly to 3.3 V or 5 V digital processing chips. The AD6600 combines an 11-bit pipeline ADC with receiver-oriented analog front-end functions in a single 44-LQFP package. Its 1 GHz input amplifiers provide wideband signal conditioning ahead of digitization, while the automatic gain-ranging block covers a 30 dB input range. These characteristics suit RF and IF sampling architectures where the received carrier must be captured directly rather than downconverted through additional mixer stages. Typical uses include dual-antenna diversity receivers, wireless infrastructure, communications test equipment, instrumentation, and other wideband sampling systems. Because the two channels provide separate gain-ranging paths, the device can support received-signal-strength measurement and diversity combining in one conversion system. A critical design consideration is the relationship between the 20 MSPS conversion rate and the 250 MHz maximum analog input frequency. PCB signal integrity, impedance control, grounding, and decoupling are essential because wideband input signals amplify supply and layout noise as well as the desired carrier. Use the pin-description table and application guidance in the manufacturer datasheet when assigning tracks, decoupling capacitors, and digital output routing. This page consolidates the verified manufacturer and distributor product information, identifies same-footprint replacement options, and adds application, comparison, and layout guidance that helps shorten evaluation time for wideband receiver-ADC designs.
AD6620ASZ - 65 MSPS Digital Receiver | Analog Devices
The Analog Devices AD6620ASZ is a 65 MSPS dual-channel digital receive signal processor with a frequency translator, two fixed-coefficient decimating filters, a programmable-coefficient decimating filter, and 3.3 V LVCMOS-compatible inputs, housed in an 80-PQFP package measuring 14 x 14 mm. The AD6620 family combines analog-to-digital conversion, frequency translation, and digital filtering in one receiver IC. A digital receive signal processor is an interface IC that samples an analog input and moves part of the signal-processing chain into the digital domain. Its functional hierarchy is ADC > digital receive signal processor > receiver interface IC > integrated circuit. Moving filtering and frequency conversion on chip reduces the need for separate external filter assemblies and can improve integration, repeatability, and channel-to-channel consistency in communications receivers. The AD6620's four cascaded signal-processing elements provide the main architectural distinction of the device. A frequency translator supports conversion away from an input carrier, while two fixed-coefficient decimating filters reduce signal bandwidth and a programmable-coefficient decimating filter adds design flexibility. The manufacturer describes the AD6620 family as a diversity receiver architecture that replaces sensitive analog filters with digital filters to reduce cost and board area. The AD6620ASZ operates from a 3.3 V-compatible digital interface and supports processing at up to 65 MSPS. These figures place the device in the high-speed signal-processing category, where conversion rate, digital filter response, interface timing, channel separation, and PCB signal integrity determine system performance. The 80-PQFP 14 x 14 mm package provides a substantial number of connections for parallel data, clocks, controls, and analog input circuitry, but it also demands careful package-outside and escape-routing planning. Typical applications include cellular diversity receivers, intermediate-frequency signal conditioning, software-defined radio front ends, wireless infrastructure, instrumentation, and other systems that require digital frequency translation followed by adjustable decimation. In these systems, the AD6620 can reduce reliance on external analog filter chains while preserving a digital path for downstream processing. The AD9643 and AD9680 are identified as newer devices with related digital-down-converter functionality, although they are not drop-in replacements for the 80-PQFP AD6620ASZ. A key design consideration is signal integrity. The parallel 3.3 V LVCMOS interface requires controlled clock routing, matched-length data connections, solid return paths, and careful separation between sensitive analog inputs and high-speed digital outputs. The 14 x 14 mm PQFP also has lead-to-lead spacing that requires examination when defining fanout, assembly rules, test access, and component placement around the device. This product record combines the confirmed 65 MSPS architecture, 3.3 V LVCMOS input compatibility, 80-PQFP package information, verified lifecycle indication, drop-in comparison, and practical receiver-design guidance. It also distinguishes exact package compatibility from newer functionally related converters that require a complete design review rather than a simple PCB substitution.
AD6623ASZ - 4-Channel 104 MSPS Transmit Signal Processor | ADI
The Analog Devices AD6623ASZ is a four-channel Transmit Signal Processor (TSP) that generates high-bandwidth intermediate-frequency data for Transmit Digital-to-Analog Converters (TxDACs), supporting operation at up to 104 MSPS in a 128-lead MQFP package measuring 14 mm by 20 mm. The processor accepts baseband data from a digital signal processor and prepares parallel digital IF outputs for compatible TxDAC signal chains. A Transmit Signal Processor is a digital signal-processing IC positioned between a DSP or FPGA and a high-speed transmit DAC. It converts baseband or channelized digital information into the digital IF format required by selected TxDAC architectures. Within the broader hierarchy of digital up-converters, interface ICs, data converters, and signal-chain semiconductors, the AD6623 provides repeatable digital IF generation rather than performing the final analog conversion itself. The AD6623 provides four processing channels, 18-bit parallel digital IF outputs, and an 18-bit bidirectional parallel digital IF input/output path. The input/output interface supports cascading multiple devices for additional channels. The manufacturer identifies the AD6623 as pin-compatible with the AD6622 and capable of operating in AD6622-compatible control-register mode, which helps simplify upgrades between those signal-processing architectures. Its power architecture uses a 2.5 V CMOS core, 3.3 V output supply, and 5 V input supply. This separation supports lower-voltage internal logic while accommodating higher-voltage digital interfaces and external circuitry. The 104 MSPS processing rate enables narrowband digital IF generation for communications, radar, and instrumentation systems where direct IF generation offers manufacturing repeatability and flexible channel configuration. Typical applications include multi-channel digital transmitter front ends, wireless communications infrastructure, radar signal generation, test and measurement equipment, and broadband industrial systems using TxDACs. The four-channel architecture can reduce the number of separate digital processing paths when several output channels must be generated coherently from common baseband data. Layout should preserve controlled clocking, differential data routing, and clean supply distribution across all 128 leads. Review the manufacturer pin-description table and recommended decoupling network before schematic capture, and verify the exposed thermal strategy and maximum operating conditions for the selected 14 mm by 20 mm MQFP assembly. This product page combines the manufacturer’s device description, package and interface characteristics, drop-in compatibility information, sourcing details, and practical implementation guidance. It also identifies where detailed pin assignments, electrical limits, clock requirements, and application-specific values must be taken directly from the AD6623 datasheet.
AD6644 - 14-Bit 65 MSPS ADC | Analog Devices | Wideband
The AD6644 is a high speed, high performance, monolithic 14-bit analog-to-digital converter (ADC) from Analog Devices. It is designed for wideband, multichannel, multimode receivers and is part of the SoftCell transceiver chipset. The device operates at guaranteed sample rates of 65 MSPS (with a 40 MSPS version available) and provides CMOS-compatible digital outputs in twos complement format. It is packaged in a 52-lead Plastic Low Profile Quad Flat Pack (LQFP) and is specified for operation from -25°C to +85°C. An analog-to-digital converter (ADC) is a critical component in signal processing chains that converts continuous analog signals into discrete digital values for processing by digital systems. The AD6644 is a high-speed, high-resolution ADC, positioned in the hierarchy of data converters: ADC -> high-speed ADC -> wideband ADC -> IF-sampling ADC. It integrates a track-and-hold (T/H) circuit and reference, providing a complete conversion solution on-chip, which simplifies system design and reduces external component count. Key features of the AD6644 include a 65 MSPS guaranteed sample rate, 100 dB multitone SFDR, and low power dissipation of 1.3 W. It features differential analog inputs, which improve common-mode noise rejection, and digital outputs that are 3.3 V CMOS-compatible, ensuring easy interfacing with modern digital logic. The device uses a three-stage subrange architecture, achieving high accuracy and speed while maintaining low power and small die size. The AD6644 is built on Analog Devices' high speed complementary bipolar process (XFCB) and uses an innovative multipass circuit architecture. This design enables high dynamic performance, making it suitable for demanding applications such as digital receivers, cellular base stations, and test equipment. The device's wideband capability allows direct IF sampling, reducing the need for multiple downconversion stages. Typical applications include multichannel, multimode receivers, software-defined radios, cellular infrastructure, and radar systems. The AD6644's high SFDR and low noise make it ideal for these applications where signal fidelity is critical. Its differential inputs and CMOS outputs simplify integration with FPGAs and DSPs. When designing with the AD6644, careful attention to decoupling and grounding is essential to achieve optimal performance. The datasheet provides detailed recommendations for power supply decoupling and PCB layout to minimize noise and ensure accurate conversion.
AD664TD-UNI/883B - 12-Bit Quad DAC, Military | Analog Devices
The AD664TD-UNI/883B is a monolithic 12-bit quad digital-to-analog converter (DAC) from Analog Devices, designed for precision multi-channel voltage-output applications. It integrates four complete 12-bit DACs on a single chip, each with a double-buffered input latch structure and data readback function. The device operates from a single external reference and is available in a 28-pin side-brazed ceramic DIP (CDIP) package, screened to military standards (MIL-STD-883). It supports unipolar (UNI) output range with a gain of one or two times the reference voltage, and features a microprocessor-compatible parallel interface for all read and write operations. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD664 is a quad DAC, meaning it contains four independent DAC channels on one chip, enabling simultaneous multi-channel analog output from a single digital interface. This device belongs to the family of data converters, which are essential in mixed-signal systems where digital processing meets the analog world. The AD664's architecture uses the BiMOS II process, combining bipolar and CMOS transistors, along with laser-trimmed thin-film resistors and double-level metal interconnects to achieve high accuracy and stability. Key features of the AD664TD-UNI/883B include four complete voltage-output DACs, data register readback, reset-to-zero override, multiplying operation, and double-buffered latches. The device offers a settling time of 10 microseconds (as per Xecor comparison data) and operates over the full military temperature range of -55°C to +125°C. The package is a 28-pin side-brazed ceramic DIP, which is suitable for high-reliability applications. The device is RoHS non-compliant, reflecting its military-grade heritage. The AD664 uses a double-buffered input latch structure, allowing all four DACs to be updated simultaneously, which is critical for applications requiring synchronized analog outputs. The data readback function enables verification of written data, enhancing system diagnostics. The reset-to-zero override forces all outputs to zero, useful for system initialization. The multiplying operation allows the reference voltage to be varied, enabling programmable gain or attenuation. Typical applications include military avionics, industrial process control, automatic test equipment (ATE), and precision instrumentation where multiple analog outputs are needed. The military screening ensures reliability in harsh environments. The parallel interface simplifies connection to microprocessors and DSPs. When designing with this device, ensure adequate decoupling on the power supply and reference pins, and consider the settling time when updating multiple channels. The device is obsolete, so verify availability and consider alternatives for new designs.
AD6654BBC - 14-Bit 92.16 MSPS 4/6-Channel IF Receiver | Analog Devices
The Analog Devices AD6654BBC is a 14-bit, 92.16 MSPS mixed-signal wideband IF-to-baseband receiver with integrated digital down-conversion, designed for communications and signal-processing systems. It supports IF sampling frequencies up to 200 MHz, includes four or six receive channels depending on the device variant, and is supplied in a 256-CSPBGA package measuring 17 x 17 mm. A wideband IF-to-baseband receiver combines an analog-to-digital converter with programmable digital down-conversion. The ADC converts wideband intermediate-frequency signals into digital data, while the DDC stages reduce those data streams toward baseband for subsequent demodulation, filtering, or FFT processing. This integration can reduce the number of separate analog and digital components required in RF and communications signal chains. The AD6654BBC provides a 14-bit conversion resolution and a maximum sampling rate of 92.16 MSPS. Its internal 2.4 V reference and 2.2 V peak-to-peak analog input range support repeatable receiver design, while the internal differential track-and-hold circuit helps capture wideband IF signals. The family supports multimode processing for WCDMA and other communications standards. The principal distinction between the six-channel and four-channel devices is channel availability. In the four-channel version, Channel 4 and Channel 5 are not available; the remaining converter and digital-processing architecture is otherwise focused on the same wideband IF receiver use case. The AD6654BBC is identified by Analog Devices as not recommended for new designs. Typical applications include wireless infrastructure receivers, WCDMA base-station equipment, communications test systems, software-defined radio platforms, and wideband IF digitization. The high conversion rate is useful when a system must sample substantial IF bandwidth directly before performing digital channelization or demodulation. The 256-CSPBGA package requires careful PCB layout, including controlled escape routing from the fine-pitch array and adequate power and ground-plane integrity. Because the manufacturer identifies the device as not recommended for new designs, engineers should verify lifecycle availability, documentation revisions, and the required software configuration before committing a new design. This page consolidates the manufacturer product information, datasheet references, package characteristics, receiver-function context, and design guidance for engineers evaluating the AD6654BBC. The Request a Quote form on this page can be used to discuss sourcing, lifecycle status, and package-related procurement requirements without relying on stale static price information.
AD6654CBC - 14-Bit, 92.16 MSPS IF Receiver | Analog Devices
The Analog Devices AD6654CBC is a 14-bit, 92.16 MSPS mixed-signal IF-to-baseband receiver combining an analog-to-digital converter with a four- or six-channel multimode digital down-converter. It supports processing of up to six WCDMA channels and is packaged in a 256-CSPBGA configuration measuring 17 mm by 17 mm. An IF-to-baseband receiver is a mixed-signal integrated circuit that converts an analog intermediate-frequency signal into digital data and then reduces or filters that data into lower-frequency channels. Within the signal-chain hierarchy, it combines an ADC, a digital down-converter, programmable signal processing, and a high-density ball-grid-array package. This integration is useful when multiple receive channels must be digitized without requiring a separate ADC and digital processing assembly for each path. The AD6654CBC provides 14-bit conversion resolution, a 92.16 MSPS conversion rate, and four or six digital down-converter channels. Its multimode DDC can process as many as six WCDMA channels, making the device suitable for multichannel receivers that require coherent sampling and programmable digital channelization. The manufacturer identifies the AD6654 as not recommended for new designs, so engineers should assess lifecycle continuity carefully before beginning a long-lived platform. The product family combines a high-speed sampling stage with digital channel-selection functions. The six-channel device is the primary focus of the manufacturer documentation. On the four-channel version, Channels 4 and 5 are unavailable, while the underlying 14-bit, 92.16 MSPS ADC architecture remains part of the AD6654 family. This distinction is important when allocating digital resources or planning receiver configurations. Typical uses include WCDMA receiver infrastructure, multi-channel IF digitization, communications test equipment, and baseband processing platforms. The ADC converts the analog IF input into parallel digital samples, while the DDC performs frequency translation and filtering to produce lower-rate channel data. Integrating these functions can reduce the number of separate conversion and digital-processing stages required in a multichannel system. Board design should prioritize short, controlled analog-input routes, stable supply and reference distribution, and careful treatment of high-speed digital outputs. The 256-ball CSPBGA requires a dense multilayer PCB with via-in-pad structures or equivalent escape routing, adequate thermal management, and assembly-process support for the selected package. Designers should use the manufacturer pin-description table when assigning every ball and power domain. This product page combines the known converter and channelization specifications with practical implementation guidance, lifecycle context, package-aware comparisons, and engineering-oriented replacement analysis. It focuses on the decisions that affect receiver architecture, PCB implementation, signal integrity, and supply planning.
AD667JN/+ - 12-Bit DAC, 10V Output | Analog Devices
Analog Devices AD667JN/+ is a complete voltage-output 12-bit digital-to-analog converter with a maximum 10 V output, 4 microsecond settling time, and a 28-pin PDIP package. The device combines a high-stability buried Zener voltage reference, a double-buffered input latch, a precision bipolar current-steering DAC core, and an on-chip output amplifier. It is designed for microprocessor-compatible control, instrumentation, waveform generation, and industrial analog-output systems operating from dual positive and negative supplies. A digital-to-analog converter is a data-conversion integrated circuit that translates a digital code into a proportional analog voltage or current. The AD667 belongs to the voltage-output DAC hierarchy, which combines a digital interface, voltage reference, resistor network, output amplifier, and current-steering core on one monolithic chip. The double-buffered latch allows a new input word to be loaded while the previous code is being converted, supporting faster system updates than an unbuffered converter. Key features include 12-bit resolution, a maximum 10 V analog output, and approximately 4 microsecond settling time. The manufacturer also describes monotonicity as guaranteed over temperature and linearity as guaranteed over temperature at 1/2 LSB maximum. A laser-trimmed thin-film resistor network supports accuracy and repeatability, while the integrated buried Zener reference supplies the internal voltage needed by the converter. The AD667JN/+ is identified as a commercial-temperature, through-hole component. Internally, the AD667 uses 12 precision high-speed bipolar current-steering switches to implement the digital-to-analog conversion. The laser-trimmed resistor network and integrated reference remove the need for external precision reference components. Its microprocessor-compatible double-buffered input architecture supports digital control systems, while the integrated output amplifier provides a voltage output from a single converter package. Typical applications include closed-loop industrial control, programmable test equipment, digital waveform generation, laboratory instrumentation, data-acquisition systems, and legacy industrial automation platforms. The dual-supply arrangement accommodates bipolar output signals and analog circuits that require both positive and negative rail headroom. The through-hole PDIP package is also suitable for repair and modernization of legacy boards where a surface-mount converter would require layout changes. When designing around the AD667JN/+, verify the analog output range, supply polarity, settling-time requirement, and logic-interface voltage before assigning signals. Keep analog and digital return currents separated where practical, and use the manufacturer pin-description table to connect the input latch, reference, amplifier, and supply pins. Because the converter is a legacy through-hole device, confirm package pin compatibility during any replacement qualification. This page organizes the AD667JN/+ electrical characteristics, verified package information, direct replacement candidates, comparison parameters, and practical selection guidance. It emphasizes what an engineer must verify when using this converter in a new design or maintaining an existing analog-control board.
AD667KN/+ - 12-Bit Voltage Output DAC | Analog Devices
The Analog Devices AD667KN/+ is a single-channel, 12-bit voltage-output digital-to-analog converter with 28 leads in a PDIP package. It combines a high-stability buried-Zener voltage reference, a double-buffered input latch, and 12 precision bipolar current-steering switches. The AD667KN/+ is intended for microprocessor-compatible systems requiring a complete, referenced DAC without a separate external reference circuit. A digital-to-analog converter, or DAC, converts a digital code into a proportional analog voltage or current. The AD667 belongs to the broader DAC family within data-conversion integrated circuits and mixed-signal semiconductor systems. Unlike a digital potentiometer or passive resistor network, this converter includes both the conversion core and a voltage reference, allowing a digital system to generate an analog output from a numeric command. The primary feature of the AD667 is its 12-bit conversion resolution, providing 4096 digital output levels. Its architecture uses 12 precision high-speed bipolar current-steering switches and a laser-trimmed thin-film resistor network. The double-buffered input latch allows a new digital input to be loaded while the previous conversion result remains available at the output, which is useful in systems that require controlled output updates. A high-stability buried-Zener reference is integrated into the device. This reference supports the converter's voltage-output operation and removes the need for an external precision reference in basic single-channel designs. The AD667 is identified as a microprocessor-compatible converter, making its parallel digital interface suitable for processors, programmable controllers, and data-acquisition equipment that can latch a 12-bit command word. Typical uses include digital potentiometer emulation, programmable voltage sources, industrial control outputs, laboratory signal generation, and embedded instrumentation. Because the converter is complete and referenced, it can simplify analog-output subcircuits while preserving a direct digital control path. System designers should still account for the required bypass capacitors, analog-ground routing, output-load limits, and the settling behavior of the selected update sequence. The most important design consideration is separating analog and digital return paths appropriately. The Analog Devices AD667 datasheet identifies the analog ground connection as the high-quality ground point for the output amplifier and recommends connecting it directly to the system analog reference point. Careful grounding helps preserve the benefit of the integrated reference and reduces coupling from digital switching activity. This product page combines the manufacturer's converter architecture, package information, sourcing guidance, and engineering-focused design considerations. It also documents the available directly comparable AD667 option, supported technical questions, and practical implementation guidance for engineers evaluating the AD667KN/+ in legacy or availability-sensitive designs.
AD667SD/883B - 12-Bit DAC, 28-CDIP | Analog Devices
The AD667SD/883B is a complete voltage output 12-bit digital-to-analog converter (DAC) from Analog Devices, featuring a high stability buried Zener voltage reference and a double-buffered input latch on a single chip. It is packaged in a 28-pin ceramic DIP (CDIP) and is designed for precision industrial and military applications. The device uses 12 precision high-speed bipolar current steering switches to achieve a settling time of 3 microseconds, ensuring fast and accurate analog output. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD667SD/883B is a voltage-output DAC, meaning it directly provides a voltage proportional to the digital input. It belongs to the family of data conversion ICs, which are essential in systems that interface digital processing with the analog world, such as microcontrollers, DSPs, and industrial control systems. The AD667 series is known for its high precision and stability, making it suitable for applications requiring accurate analog signals. Key features of the AD667SD/883B include 12-bit resolution, a single channel, and a settling time of 3 microseconds. The device operates from a +5V and -5V power supply, and it includes an internal buried Zener reference that provides excellent temperature stability. The double-buffered input latch allows for simultaneous updating of multiple DACs in a system, which is critical in multi-channel applications. The 28-pin CDIP package is hermetically sealed, offering enhanced reliability in harsh environments. Technically, the AD667SD/883B utilizes a current-steering architecture with a precision R-2R ladder network. The buried Zener reference ensures low noise and low drift over temperature, which is essential for high-accuracy applications. The device is designed to be microprocessor-compatible, with a parallel interface that can be easily connected to standard digital buses. The output voltage range is typically 0V to +10V or +/-5V, depending on the configuration, and it can drive loads up to 5mA. Typical applications include industrial process control, test and measurement equipment, and military/aerospace systems where high precision and reliability are paramount. The AD667SD/883B is also used in audio equipment for crystal-clear signal generation, as noted in comparison data. Its fast settling time and low glitch energy make it suitable for waveform generation and closed-loop control systems. When designing with the AD667SD/883B, it is important to provide adequate decoupling on the power supply pins and to ensure a clean analog ground plane. The reference output should be buffered if external loads are connected. Additionally, the digital inputs should be properly terminated to avoid noise-induced errors. The device is specified for operation over the full military temperature range of -55C to +125C, making it suitable for demanding environments.
AD6705 - 8-Bit Signal Conditioning ADC | Analog Devices
The AD6705 is an 8-bit, low-cost, signal conditioning analog-to-digital converter (ADC) from Analog Devices, designed for aerospace and industrial applications requiring precise analog-to-digital conversion with minimal external components. It integrates a complete signal conditioning front-end, including an instrumentation amplifier and a successive approximation register (SAR) ADC, enabling direct interface to sensors and transducers. The device operates from a single supply, simplifying power design and reducing system cost. An ADC (analog-to-digital converter) is a critical component in data acquisition systems that converts continuous analog signals into discrete digital values for processing by microcontrollers, DSPs, or FPGAs. The AD6705 belongs to the family of signal conditioning ADCs, which combine amplification, filtering, and conversion in a single package, reducing board space and improving noise immunity. This integration is essential in aerospace and industrial environments where signal integrity and reliability are paramount. Key features of the AD6705 include an 8-bit resolution, a single-supply operation, and a built-in signal conditioning front-end that accepts a wide range of input signals. The device offers a low-cost solution for applications that do not require high-resolution conversion but demand robustness and ease of use. Its aerospace-grade qualification ensures operation over extended temperature ranges and harsh conditions. Technically, the AD6705 employs a SAR architecture, which provides fast conversion times and low power consumption. The integrated instrumentation amplifier allows direct connection to bridge sensors, thermocouples, and other low-level signals, eliminating the need for external gain stages. The device also includes an internal reference, further reducing external component count. Typical applications include aerospace telemetry, industrial process control, and portable instrumentation. In aerospace, the AD6705 is used for monitoring pressure, temperature, and position sensors, where its reliability and signal conditioning capabilities are critical. In industrial settings, it interfaces with transducers in control loops, providing accurate digital data for process automation. When designing with the AD6705, ensure proper decoupling of the power supply and careful layout of the analog input traces to minimize noise. The device's single-supply operation simplifies power design, but attention to reference stability is necessary for accurate conversions.
AD670JN - 8-Bit Signal Conditioning ADC | Analog Devices
The Analog Devices AD670JN is an 8-bit signal-conditioning analog-to-digital converter with two inputs, a successive-approximation register, and a microprocessor bus interface. The converter is supplied in a 20-pin PDIP package and operates as a complete monolithic signal-conditioning ADC, integrating an instrumentation-amplifier front end, DAC, comparator, SAR, precision voltage reference, and three-state output buffer. According to the manufacturer datasheet, no external components or user trims are required to interface the device. The AD670 is positioned as a low-cost converter for acquiring bipolar or unipolar sensor signals with input conditioning included on the same chip. Its specified conversion speed is 10 microseconds, making it suitable for control, measurement, and instrumentation systems that require an 8-bit result but do not need the resolution or throughput of a modern high-resolution ADC. The 20-pin PDIP package is a through-hole format rather than a compact surface-mount option, which can simplify prototyping and replacement on older industrial and instrumentation boards. The AD670JN is listed as obsolete by ZDI, so procurement should account for limited original-equipment availability and possible premium pricing. Its 8-bit resolution gives 256 quantization levels, while the integrated instrumentation front end reduces the number of external analog components required around the converter. Engineers should verify supply voltage, input range, common-mode limits, reference behavior, interface timing, and acquisition sequencing against the manufacturer datasheet before adapting the device to a new design. Because the product is obsolete, any new production design should normally preserve the AD670JN footprint only when no functional and lifecycle-qualified alternative exists. An ADC is an analog-to-digital converter, a semiconductor in the data-converter category that translates a continuous voltage into a digital code. The AD670JN belongs to the successive-approximation-register ADC family and combines that conversion mechanism with analog signal conditioning and a parallel microprocessor interface. A SAR ADC determines its result by successively comparing the input against an internally generated DAC level. The AD670 extends this basic conversion function with an instrumentation-amplifier front end, internal precision reference, comparator, and tri-state output buffer. This integration places the device in the hierarchy of ADC, data-converter IC, signal-conditioning converter, and general-purpose semiconductor. The integrated front end is especially relevant where a sensor produces a small differential signal riding on a larger common-mode voltage, because external amplification and offset conditioning would otherwise increase component count, board area, and calibration complexity. The primary features identified in the verified manufacturer materials include complete 8-bit signal conditioning, a differential-input instrumentation-amplifier front end, a precision internal voltage reference, a microprocessor bus interface, and a conversion speed of 10 microseconds. The differential front end supports direct connection of suitable sensor outputs and rejects common-mode voltage to the extent permitted by the device's operating limits. The internal DAC, comparator, and SAR form the conversion core, while the three-state output buffer permits controlled connection to shared data buses. Because the converter includes the major analog blocks, it can reduce external passive-component and trimming requirements. Its 8-bit resolution divides the supported measurement span into 256 codes, making it appropriate for position, level, threshold, and proportional feedback systems where one least-significant bit is adequate. The AD670JN uses a successive-approximation conversion architecture rather than a flash, pipeline, or sigma-delta architecture. SAR conversion is well suited to this device's stated 10-microsecond speed because it combines moderate throughput with an integrated monolithic implementation. The instrumentation-amplifier front end converts the conditioned input into a form that the comparator can evaluate against the internal DAC. During conversion, the successive-approximation logic successively updates the DAC, compares its voltage with the conditioned input, and records each comparison as one bit of the 8-bit result. The internal precision reference establishes the comparison scale. A microprocessor can read the converted byte through the parallel bus when the converter indicates completion. Tri-state outputs reduce bus contention when multiple converter outputs share a bus, provided the interface is sequenced correctly. Typical uses include industrial process measurement, laboratory instrumentation, transducer signal acquisition, closed-loop position control, and legacy embedded control equipment. The integrated front end is useful when the source is differential and its amplitude is within the AD670's input and common-mode limits. The 10-microsecond conversion rate permits sampling of relatively slow variables such as temperature, pressure, position, and analog control feedback. Because the converter resolution is only 8 bits, it should not be selected for applications requiring precise waveform reconstruction, high dynamic range, or fine quantization. The PDIP-20 package also favors through-hole legacy equipment and industrial control cards rather than compact wearable or high-density embedded systems. The obsolete lifecycle status makes continuity of supply a central selection consideration. The primary design concern is analog input conditioning. Engineers should verify the supported bipolar or unipolar input range, input impedance, common-mode range, differential input limits, and required source impedance against the manufacturer datasheet before applying external sensors. Grounding and decoupling must preserve reference stability and minimize conversion error. The microprocessor interface timing and output enable behavior must also be observed because the tri-state bus is intended for controlled system-level access. Since exact pin assignments, supply limits, and timing values were not supplied in the verified web data, they must not be inferred from generic AD670-family descriptions. New designs should also account for obsolescence, counterfeit screening, and a possible PCB redesign if a currently supported converter offers better resolution, packaging, or lifecycle assurance. This page consolidates the verified distributor and manufacturer information for the AD670JN, including its obsolete status, 8-bit SAR architecture, 10-microsecond conversion speed, 20-pin PDIP package, pricing indication, and engineering-oriented replacement considerations. It also distinguishes verified facts from data requiring confirmation from the full manufacturer datasheet. That distinction is important for an obsolete converter, where package variants, temperature grades, screening levels, and supply conditions can materially affect drop-in qualification.
AD670JP - 8-Bit 2-Input SAR ADC | Analog Devices | PLCC-20
The Analog Devices AD670JP is an 8-bit, 2-input successive-approximation register analog-to-digital converter in a 20-pin PLCC package measuring 9 mm by 9 mm. It provides a parallel digital interface and supports bipolar or unipolar input configurations through an integrated signal-conditioning path. The AD670JP is designed for compact industrial measurement and control systems where an 8-bit conversion result is sufficient but the added flexibility of differential input and internal reference can simplify board design. An ADC is an integrated circuit that converts a continuously varying analog voltage into a numeric code. Within the semiconductor hierarchy, the AD670JP belongs to the data-converter IC class and more specifically to the ADC category. Its successive-approximation register architecture compares the unknown input against an internal DAC, one binary bit at a time, until the converted code is resolved. Parallel output presents the completed digital result directly on dedicated output pins rather than relying on a serial clock and data line. The AD670JP provides one converter with two input connections and 8-bit resolution. The 20-pin PLCC package supports surface-mount assembly, while the AD670 family also includes A-grade and B-grade versions specified from -40 °C to +85 °C and an S grade specified from -55 °C to +125 °C. Internal reference architecture, differential input, and selectable input polarity broaden its usefulness for transducer, control, and instrumentation applications. Because its resolution is 8 bits, the converter provides 256 discrete output codes. The AD670JP is therefore appropriate where precise proportional measurement, position sensing, process monitoring, or digital control is more important than fine quantization. Because parallel outputs require dedicated board routing and shielding from switching noise, the device is generally better suited to moderate-speed acquisition than to high-pin-count, very high-rate converter systems. Typical applications include industrial sensor interfaces, digital thermometry, analog control-loop monitoring, position and transducer measurement, panel meters, and low-cost embedded data-acquisition boards. A PLCC footprint also makes AD670JP relevant to legacy industrial equipment and maintenance inventories where changing the original converter would require redesigning the PCB rather than merely replacing the component. The main design consideration is that an 8-bit result limits system resolution to roughly 0.4% of full scale after accounting for endpoint behavior and practical signal conditioning. The board should provide clean analog routing, adequate bypassing, and input protection appropriate to the measured signal. Compatibility with a replacement part must be confirmed from the manufacturer datasheet rather than inferred from the converter resolution alone. This page consolidates the verified distributor listing, manufacturer family information, package details, temperature-grade options, and cross-reference evidence for AD670JP. It also identifies where public data is incomplete, including pricing, sampling rate, exact pin naming, and confirmed multi-part substitutes, so engineers can make sourcing decisions without treating unavailable specifications as established facts.
AD670KN - 8-Bit Signal Conditioning ADC | Analog Devices
Analog Devices AD670KN is a complete 8-bit signal-conditioning analog-to-digital converter with two analog input channels, a 5 V supply, and a conversion time of 10 µs. The monolithic device integrates an instrumentation-amplifier front end, DAC, comparator, successive-approximation register, precision voltage reference, and tri-state output buffer. It is offered in a 20-pin ceramic DIP package for the K-temperature grade. An ADC is a signal-conditioning ADC that converts an analog input voltage into a digital code for processing, measurement, logging, or control. The AD670 belongs to the broader ADC and data-converter hierarchy within integrated circuits. Unlike a bare flash or successive-approximation converter, the AD670 combines input amplification, reference generation, conversion, and digital output buffering on one monolithic device. The AD670KN requires no external components or user calibration trims for normal operation, simplifying analog-system implementation. Its 8-bit resolution corresponds to 256 digital output codes, making it appropriate for position, level, process-control, and instrumentation measurements that do not require higher conversion resolution. The integrated voltage reference supports repeatable conversion behavior, while the tri-state output buffer provides controlled output-bus connection and disconnection. Internally, the converter uses a successive-approximation register with comparator and DAC feedback to determine each digital result. The instrumentation-amplifier front end conditions the analog signal before conversion, reducing the number of external signal-conditioning stages required. This integrated architecture is particularly useful when the source has a limited voltage range and the application requires a complete converter rather than a bare ADC core. Typical uses include industrial process measurement, laboratory instrumentation, sensor interfaces, data acquisition, embedded control, and legacy equipment requiring an 8-bit conversion function. Two analog channels support dual-input measurements or differential-style sampling when paired with the appropriate signal arrangement. The 10 µs conversion time permits updates in the low-kilohertz range, depending on acquisition timing and system overhead. Designers should account for the analog input range, acquisition timing, reference behavior, output coding, and electrical characteristics stated in the manufacturer datasheet. Confirm pin assignments, input common-mode limits, and timing requirements before layout because the AD670KN uses a 20-pin ceramic DIP rather than a surface-mount package. The complete integration reduces external circuitry but leaves less routing flexibility than a modular converter.
AD670KP - 8-Bit 10 us Dual-Input SAR ADC | Analog Devices
The Analog Devices AD670KP is a complete 8-bit signal-conditioning analog-to-digital converter with two analog inputs, a 10 microsecond conversion time, and parallel digital output in a 20-terminal PLCC package. It integrates an instrumentation-amplifier front end, DAC, comparator, successive-approximation register, precision voltage reference, and three-state output buffer on one monolithic bipolar chip. According to the manufacturer product page, the K grade is specified from 0°C to +70°C and is offered in a 20-terminal PLCC package. An ADC converts an analog voltage into a digital code for measurement, control, instrumentation, or data acquisition. The AD670KP belongs to the SAR ADC family: a successive-approximation register compares the input against an internally generated DAC level during successive clock cycles. SAR ADCs are useful where parallel outputs, modest resolution, moderate conversion speed, and integrated signal conditioning are more important than compact serial-interface power savings. The integrated instrumentation amplifier is particularly relevant for sensors and low-level differential signals. Verified source data identifies the AD670KP as an 8-bit parallel-output ADC with two analog input channels, a 0.195% linearity-error figure, and a 10 microsecond conversion time. The device needs no external components or user trims for full-accuracy operation according to the retrieved datasheet description. Its precision voltage reference supports a self-contained conversion chain, while the three-state output buffer can provide a controlled output state for shared digital buses. The monolithic bipolar implementation combines analog input conditioning and digital conversion logic in one package. This integration reduces the number of external precision components and simplifies board-level signal-chain design. A parallel 8-bit interface is appropriate for processors, programmable controllers, counters, data loggers, and embedded systems that can latch the converted code directly. Because only 8 bits are available, the converter is better suited to coarse measurements, position feedback, process monitoring, and control loops than to high-resolution signal analysis. Typical uses include industrial process measurement, sensor-interface systems, panel controls, instrumentation, and embedded data acquisition. The dual inputs allow the converter to monitor more than one analog quantity when system timing and multiplexing requirements permit. Designers should verify input range, acquisition timing, logic levels, reference behavior, and output timing against the current Analog Devices datasheet before fixing the PCB or firmware. A key integration advantage is that the instrumentation amplifier, DAC, comparator, SAR logic, voltage reference, and tri-state output buffer are combined on one chip. The trade-off is its 8-bit resolution: it provides economical acquisition but cannot distinguish finely spaced analog levels as effectively as a 12-bit or higher-resolution converter. This page synthesizes the verified AD670KP specifications, sourcing links, application guidance, and replacement limitations. It does not infer unverified electrical limits or invent drop-in substitutes where the available cross-reference data does not establish same-package, pin-compatible alternatives.
AD673JD - 8-Bit SAR ADC, 30 us | Analog Devices
Analog Devices AD673JD is a complete 8-bit successive-approximation analog-to-digital converter with a 30 us maximum conversion time, integrating a DAC, voltage reference, clock, comparator, successive-approximation register, and three-state output buffers on one monolithic chip. The device supports unipolar and bipolar inputs, operates from +5 V and -15 V supplies, and is packaged in a 20-pin ceramic dual in-line package. An ADC is a data-conversion component that transforms an analog voltage into a digital number for processing, measurement, or control. Successive-approximation, or SAR, ADCs repeatedly compare the input against an internal DAC until their difference falls within the converter's resolution. The AD673JD belongs to the ADC and DAC category within integrated circuits and offers a simple parallel data interface for microprocessor-based measurement systems. The converter's principal features include complete 8-bit conversion, no missing output codes over temperature, and support for either full or 16-bit microprocessor bus interfacing. Its integrated reference, clock, comparator, DAC, and register reduce the number of external components required in a measurement circuit. Three-state output buffers permit the data bus to be placed into a high-impedance state when multiple devices share common bus lines. The AD673 uses a successive-approximation conversion architecture in which an internal DAC generates trial voltages during each conversion cycle. A comparator evaluates the trial voltage against the analog input, and the successive-approximation register records the binary decision sequence. The resulting eight digital outputs represent the converted input, while the conversion-status output can support processor-controlled acquisition timing. Typical uses include industrial process measurement, instrumentation, data acquisition, embedded control, and legacy microprocessor interfaces. The device is particularly useful where an 8-bit measurement resolution is sufficient but a complete converter with an internal reference is preferred over a discrete resistor ladder and external comparator. The principal design consideration is the negative supply requirement. Layout should keep analog input and reference paths away from digital switching traces, while decoupling should follow the connection and grounding recommendations in the manufacturer datasheet. Because the AD673JD operates with +5 V and -15 V supplies, system designers should verify negative-rail generation and signal-reference compatibility before layout release. This product page organizes the AD673JD specifications, functional characteristics, application guidance, and same-footprint upgrade choices for faster engineering evaluation. It also identifies where the complete pin assignment and detailed electrical limits must be confirmed in the manufacturer datasheet before a new PCB is manufactured.
AD673JN - 8-Bit SAR ADC with Reference | Analog Devices
Analog Devices AD673JN is a complete 8-bit successive-approximation analog-to-digital converter with an integrated DAC, voltage reference, clock, comparator, successive-approximation register, and three-state output buffers. It converts a unipolar or bipolar analog input through a 20-pin plastic DIP package and supports microprocessor interfacing through full-byte or 16-bit bus modes. An ADC converts a continuously varying analog voltage into a digital value for processing, measurement, or control. The AD673 belongs to the successive-approximation ADC category, within the broader hierarchy of data-converter ICs and signal-processing semiconductors. Rather than requiring a separate reference, comparator, clock, and internal DAC, the AD673 combines these functions on one monolithic chip, simplifying instrumentation and industrial data-acquisition designs. Key features include 8-bit resolution, a maximum conversion time of 30 microseconds, unipolar and bipolar input capability, and no missing codes over the specified temperature range. The converter operates from +5 V and -15 V supplies, while its integrated voltage reference, internal clock, and three-state output buffers reduce external component count. These characteristics suit process monitoring, digital instrumentation, industrial control, and embedded measurement systems requiring deterministic acquisition timing. The internal successive-approximation function uses integrated injection logic, and the internal DAC uses a laser-trimmed, high-stability silicon-chromium thin-film resistor ladder. A temperature-compensated subsurface Zener reference supports stable conversion performance. Full-byte or 16-bit microprocessor bus interface options allow the converter to operate with processors using either byte-oriented or wider parallel data arrangements. Typical applications include industrial process measurement, laboratory data-acquisition systems, digital panel meters, embedded control platforms, and legacy computer interface cards. In each case, the integrated converter functions simplify the analog front end while the 30 microsecond maximum conversion time provides a defined upper bound for sampling cycles. When designing the circuit, preserve the negative supply arrangement required by the converter and use the manufacturer pin-description table when assigning data-bus and control signals. Verify input range, output coding, timing, and acquisition-system settling requirements against the Analog Devices AD673 datasheet before fixing the analog front-end and bus timing. This product overview combines the converter architecture, interface considerations, drop-in family options, and practical selection guidance into an engineering-focused reference for designers evaluating the AD673JN for new or legacy data-acquisition equipment.
AD674BTE/883B - 12-Bit SAR ADC, 28-CDIP | Analog Devices
The AD674BTE/883B is a complete 12-bit successive approximation analog-to-digital converter (ADC) from Analog Devices, featuring an internal high-precision voltage reference and clock. It is packaged in a 28-pin ceramic dual-in-line package (CDIP) and is designed for direct interface to 8- and 16-bit microprocessor buses via three-state output buffers. The device operates from ±12V and +5V supplies and converts in a maximum of 15 microseconds, making it suitable for high-speed data acquisition systems. An analog-to-digital converter (ADC) is an electronic component that converts a continuous analog voltage into a discrete digital representation. The AD674BTE/883B is a successive approximation register (SAR) ADC, which uses a binary search algorithm to determine the digital output. SAR ADCs are known for their high speed and moderate resolution, making them ideal for industrial control, instrumentation, and data acquisition. The AD674B family is pin-compatible with the industry-standard AD574A but offers faster conversion time and lower power consumption. Key features of the AD674BTE/883B include 12-bit resolution, a maximum conversion time of 15 µs, and an internal 10V reference. It accepts bipolar input ranges of ±5V and ±10V, as well as unipolar 0V to 10V and 0V to 20V, selectable via pin strapping. The device includes a three-state output buffer for direct bus interfacing and operates over the extended temperature range of -55°C to +125°C, meeting MIL-STD-883B standards. Technically, the AD674BTE/883B integrates a precision voltage reference, clock, and comparator on-chip, reducing external component count. The SAR architecture ensures monotonicity and no missing codes over the full temperature range. The device features a 12-bit parallel output with a status pin (STS) that indicates conversion completion, simplifying microprocessor handshaking. The 28-pin CDIP package provides excellent thermal and mechanical stability for harsh environments. Typical applications include military and aerospace data acquisition, industrial process control, medical instrumentation, and scientific analysis equipment. The device's wide operating temperature range and high reliability make it suitable for mission-critical systems where accuracy and durability are paramount. When designing with the AD674BTE/883B, ensure proper decoupling of the power supplies and a clean analog ground plane to minimize noise. The internal reference can be overridden by an external reference for improved accuracy, but the internal reference is sufficient for most applications. The conversion start (CE, CS, R/C) control pins allow flexible timing, and the STS pin can be used to trigger interrupts or polling routines.
AD676AD - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD676AD is a 16-bit, single-channel, parallel-output sampling analog-to-digital converter with a conversion rate of 100 kSPS, housed in a 28-CDIP package. It uses a switched-capacitor charge-redistribution architecture and an on-chip autocalibration function to support accurate signal acquisition. The verified product information identifies the AD676AD as a 28-pin SAR ADC with one analog input, 16-bit resolution, parallel output, and a 10 µs total conversion time. A sampling ADC samples an analog input through an internal sample-and-hold function and converts it into a digital value. The SAR, or successive-approximation-register, architecture is suited to instrumentation, measurement, and signal-processing systems requiring moderate conversion speed and high resolution. The AD676AD belongs to the broader ADC, data-conversion, and analog-signal-processing hierarchy, and its parallel interface can simplify connections to suitable digital acquisition logic. Key verified features include 16-bit resolution, 100 kSPS conversion performance, autocalibrating on-chip sample-and-hold, and a parallel output format. The device is also described as having no missing codes, 1 LSB integral nonlinearity, 97 dB THD, 90 dB signal-to-noise-plus-distortion ratio, and 1 MHz full-power bandwidth according to the supplied ADI-related technical listing. These figures describe the converter's intended acquisition performance, but system-level results also depend on reference quality, analog conditioning, clocking, layout, and digital post-processing. The AD676 uses a switched-capacitor/charge-redistribution architecture and digitally corrects internal nonlinearities through on-chip autocalibration. Autocalibration supports consistent conversion behavior in measurement applications, while the parallel output format allows the converted word to be captured by compatible logic. The supplied manufacturer documentation emphasizes both dynamic specifications, such as THD and S/(N+D), and DC parameters relevant to precision measurement. Typical applications include industrial process measurement, instrumentation, laboratory data acquisition, sensor-interface systems, and embedded measurement platforms. The 100 kSPS rate is suitable for sampling many control, monitoring, and waveform-related signals while the 16-bit word provides high nominal resolution. The 28-CDIP package is through-hole and requires careful board-level pin mapping and signal-integrity planning. When designing around the AD676AD, preserve the required reference, analog input, digital interface, and power connections specified by the manufacturer datasheet. Validate the complete signal chain with the intended source impedance, sampling interval, and calibration sequence. Because the verified results do not provide a complete pinout or operating-temperature table in the supplied material, those details must be confirmed from the official AD676 datasheet before layout or production release.
AD676BD - 16-Bit 100 kSPS Sampling ADC | Analog Devices
The Analog Devices AD676BD is a 16-bit, 100 kSPS single-input sampling analog-to-digital converter with parallel output in a 28-pin CDIP package. It uses switched-capacitor charge redistribution, completes conversion in 10 microseconds, and includes an on-chip autocalibration function and sample-and-hold circuit. A sampling ADC samples an analog input and converts it into a digital code for measurement, instrumentation, signal processing, and control systems. The AD676 belongs to the SAR ADC family, where successive approximation compares the sampled voltage against an internal DAC. Its parallel output presents all 16 result bits together rather than serializing them through a shift register, which supports simpler data capture at moderate clock rates. The verified device data identifies 16-bit resolution, 100 kSPS conversion throughput, one SAR input, no missing codes, 1 LSB integral nonlinearity, 97 dB THD, 90 dB signal-to-noise-plus-distortion ratio, and 1 MHz full-power bandwidth. On-chip autocalibration digitally corrects internal nonlinearities. The parallel interface provides 16-bit output data, while the integrated sample-and-hold function reduces the external sampling circuitry required. The AD676 datasheet also identifies dynamic and direct-current specifications. Dynamic parameters such as S/(N+D), THD, and IMD characterize signal-chain behavior, while DC parameters support precision measurement. The 28-CDIP mechanical format through-hole package is larger than modern leadless options but remains useful where through-hole construction, serviceability, and legacy instrument compatibility are priorities. Typical uses include industrial measurement, process monitoring, audio and signal processing, data acquisition, and precision instrumentation. Design implementation must observe the manufacturer's analog, digital, reference, and power-supply requirements. Because acquisition accuracy depends on the complete signal chain, reference stability, source impedance, grounding, clock quality, and input bandwidth are as important as nominal converter resolution. This page combines exact verified specifications, official documentation links, commercial availability references, and application guidance. It does not invent unreported electrical, environmental, pricing, pinout, or compliance values; unavailable engineering data remains explicitly identified in the specifications.