بەرهەمەکان (3,600+)

ADS830EG4 - 8-Bit 60MSPS Pipelined ADC | Texas Instruments
ADS830EG4

ADS830EG4 - 8-Bit 60MSPS Pipelined ADC | Texas Instruments

The Texas Instruments ADS830EG4 is an 8-bit, 60-MSPS pipelined CMOS Analog-to-Digital Converter (ADC) that operates from a single +5V power supply, housed in a 20-pin SSOP package. It provides excellent dynamic performance with a single-ended input and can also be operated with a differential input for improved spurious performance. The device includes an 8-bit quantizer, high-bandwidth track-and-hold, and a high-accuracy internal reference, making it suitable for high-speed signal acquisition. The G4 suffix indicates a Pb-free (lead-free) green RoHS-compliant package version supplied in tape and reel. An Analog-to-Digital Converter (ADC) is a semiconductor device that converts real-world analog signals into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. Within the broader signal chain hierarchy, an ADC sits between a sensor/amplifier front end and a digital processor; pipeline ADCs use a multi-stage architecture to achieve high sampling rates (tens to hundreds of MSPS) at moderate resolution (8-14 bits), trading latency for speed. The ADS830 belongs to the pipelined ADC subcategory, which is the dominant architecture for communications, video, and imaging applications requiring both high sample rate and continuous streaming conversion. Key features of the ADS830EG4 include a maximum sampling rate of 60 MSPS, single-ended input range of 1.5V to 3.5V (programmable), and a pipelined architecture with internal reference. The device supports both single-ended and differential input modes and is pin-for-pin compatible with the 8-bit, 80-MHz ADS831 for upgrade flexibility. Power consumption is approximately 215 mW at 60 MSPS from a single +5V analog supply, with a power-down mode available for low-duty-cycle applications. The ADS830EG4 is commonly used in digital communications (IF sampling, QAM demodulation), video digitisation (broadcast equipment, professional cameras), CCD imaging scanners, and portable instrumentation. Its single +5V operation simplifies power-tree design in legacy +5V systems, while the SSOP-20 footprint eases hand-soldering and rework in low-volume production. Differential-input mode further enables low-distortion sampling of transformer-coupled IF signals in software-defined radio receivers. When designing with this device, pay attention to input common-mode voltage and reference decoupling. Use a low-impedance analog ground plane, place the input coupling capacitor close to the AIN pin, and provide a clean +5V AVDD rail with 0.1uF and 10uF decoupling. For best SFDR in IF-sampling applications, operate the input in differential mode with a wideband balun. Refer to the TI ADS830 datasheet (SBAS167 family) for full application-circuit recommendations and timing diagrams. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
ADS8318IDRCR - 16-Bit 500kSPS SAR ADC | Texas Instruments | SON-10
ADS8318IDRCR

ADS8318IDRCR - 16-Bit 500kSPS SAR ADC | Texas Instruments | SON-10

The Texas Instruments ADS8318IDRCR is a 16-bit, 500-kSPS, serial-interface, micropower, miniature SAR analog-to-digital converter in a 10-pin VSON (DRC) 3x3 mm package. According to TI's product page, the device operates from a single 4.5V to 5.5V supply, supports a unipolar differential input, and delivers serial output through an SPI/QSPI/MICROWIRE-compatible port. The ADS8318 achieves 16-bit no-missing-code performance with an integral non-linearity (INL) of ±0.0023% FSR and a conversion time of approximately 1.4 us, making it well suited for high-precision data acquisition. A SAR (Successive Approximation Register) ADC is a type of analog-to-digital converter that uses a binary search algorithm against an internal precision DAC to digitize an input voltage in N clock cycles, where N is the resolution in bits. SAR ADCs offer deterministic latency, no pipeline delay, and excellent DC accuracy, which is why they are widely used in precision industrial sensing, weigh scales, instrumentation, and process control. Within the broader taxonomy, the SAR ADC belongs to the data converter family, which sits inside signal chain ICs and ultimately under power management and analog signal chain semiconductors. Key features include an unipolar differential input that simplifies front-end signal conditioning, ultra-low power dissipation of approximately 18 mW at 500 kSPS, and a power-down mode that reduces current to a few microamps between conversions. The device uses an external reference voltage, allowing the user to trade off input range versus noise. Its SPI-compatible serial interface reduces board-routing complexity compared to parallel ADCs, while the small 3x3 mm VSON package enables high-density layouts. In terms of architecture, the ADS8318 integrates a sample-and-hold, a precision DAC, a comparator, and an SAR register. The conversion process is initiated by CONVST and completed via an external serial clock. The DRC package includes an exposed thermal pad to lower junction-to-board thermal resistance, which helps the part sustain 500 kSPS throughput without thermal throttling in compact layouts. Typical uses span handheld test equipment, multi-channel data-acquisition systems, optical module monitoring, battery management systems, and industrial process control. The differential input is especially valuable where ground-loop noise or single-ended signal swings must be rejected. When designing with this part, pay close attention to the reference bypass network (a 10 uF tantalum in parallel with 0.1 uF ceramic is typical), keep analog and digital grounds separated until they meet at a single point, and avoid driving the analog input directly from a high-impedance source without an input buffer. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.

RFQ پەیوەندی
ADS831E - 8-Bit 80-MSPS ADC | Texas Instruments
ADS831E

ADS831E - 8-Bit 80-MSPS ADC | Texas Instruments

The Texas Instruments ADS831E is an 8-bit, 80-MSPS single-input pipelined CMOS analog-to-digital converter in a 20-pin SSOP package. It operates from a single +5 V supply and accepts single-ended or differential analog inputs, with a verified single-ended input range of 1.5 V to 3.5 V. An ADC is a data-acquisition semiconductor that samples an analog voltage and converts it into a digital code. The ADS831E belongs to the pipeline ADC family within data converters and ICs. Its high-bandwidth track-and-hold circuit samples the input rapidly, while the pipeline architecture supports conversion rates up to 80 million samples per second for communications, video, medical imaging, and test-instrumentation systems. Key verified features include an 8-bit quantizer, 80-MSPS maximum sampling rate, 49 dB high SNR, 275 mW low power, 0.35 LSB low DNL, internal or external reference options, and programmable input range. The converter supports single-ended operation for conventional analog signals and differential operation when improved spurious performance is required. The device operates from one +5 V supply and is specified in a 20-SSOP package. The TI product page identifies low distortion and high SNR as useful for medical imaging, communications, video, and test instrumentation. The verified single-ended range is 1.5 V to 3.5 V, giving the system designer a defined input window for analog front-end scaling and reference selection. Typical signal-chain implementation places the analog source, driver or front end, and ADS831E before a digital processor or FPGA. The 80-MSPS rate supports high-speed waveform acquisition, communications-channel digitization, video sampling, and instrumentation. Differential input can reduce common-mode sensitivity and improve spurious performance, while internal reference support simplifies designs that do not require an external reference voltage. Designers should confirm the complete electrical limits, reference requirements, timing, pin functions, and thermal limits in the TI ADS831 datasheet and the ADS831E ordering information. The available verified data does not establish a public price for every quantity tier, so purchasing decisions should use distributor confirmation rather than an assumed price.

RFQ پەیوەندی
ADS831E/2K5G4 - 8-Bit 80MSPS ADC, 5V, SSOP-20 | Texas Instruments
ADS831E/2K5G4

ADS831E/2K5G4 - 8-Bit 80MSPS ADC, 5V, SSOP-20 | Texas Instruments

The Texas Instruments ADS831E/2K5G4 is an 8-bit, 80 MSPS pipelined analog-to-digital converter (ADC) with one single-ended or differential input channel and a parallel digital interface, supplied on a 20-pin SSOP (0.154 inch / 3.90 mm body width) tape-and-reel package. It operates from a single +5 V supply, supports an internal or external reference, and provides a programmable input range of ±2 Vp-p. Key headline parameters are 80 MSPS sampling rate, 49 dB SNR, 275 mW typical power dissipation, and 0.35 LSB DNL. An ADC (analog-to-digital converter) is a data-acquisition integrated circuit that samples continuous analog signals and quantizes them into discrete digital codes for processing by microcontrollers, DSPs, FPGAs, or ASICs. Pipeline ADCs like the ADS831E use a multi-stage architecture that converts one sample per clock cycle after a fixed latency, achieving a strong balance between sampling speed, resolution, and power consumption; they sit within the broader taxonomy of Nyquist-rate ADCs alongside successive-approximation register (SAR) and flash converters, and belong to the data-converter family of mixed-signal ICs. The device includes a high-bandwidth track-and-hold (T/H), an 8-bit quantizer, an internal bandgap-derived reference that can be overdriven by an external reference, and a programmable input range set by an external resistor. The differential input mode yields improved spurious-free dynamic range (SFDR) compared to single-ended operation, which is valuable when sampling IF or baseband signals in communications receivers. CMOS pipeline architecture delivers low-power operation at 275 mW typical while maintaining the 49 dB SNR figure at the Nyquist frequency. Typical applications include CCD imaging front ends, digital still cameras, video capture cards, set-top box video digitizers, portable medical imaging devices, communications IF sampling, and general-purpose high-speed data acquisition. The 5 V analog supply and parallel interface simplify integration into legacy industrial designs and FPGA-based DSP pipelines. When designing with this part, observe the input common-mode range when using the internal reference and place the input RC network close to the analog input pin to preserve the wide track-and-hold bandwidth; for best SNR use the differential input mode and bypass the reference pin with a low-ESR 10 uF tantalum plus 0.1 uF ceramic combination as recommended in the manufacturer datasheet.

RFQ پەیوەندی
ADS8320-HT - 16-Bit 100kSPS High-Temp SAR ADC | Texas Instruments
ADS8320-HT

ADS8320-HT - 16-Bit 100kSPS High-Temp SAR ADC | Texas Instruments

The Texas Instruments ADS8320-HT is a 16-bit, high-speed, micropower successive approximation register (SAR) analog-to-digital converter, ensured over a 2.7V to 5.25V supply range and rated for -55C to +210C operation in an 8-pin ceramic surface-mount package. It samples at up to 100 kSPS while drawing very little power. An ADC converts continuous analog signals into discrete digital values for processing by MCUs or DSPs. Within the data-converter hierarchy, the ADS8320-HT belongs to the SAR ADC family, which trades lower throughput than delta-sigma converters for low latency, low power, and simple single-shot operation - ideal for high-temperature data acquisition nodes. Key features include true 16-bit resolution, a differential input for flexible signal conditioning, and a reference input that accepts any voltage from 500 mV to VCC, letting designers scale the full-scale range to match sensors directly. The synchronous serial interface (SPI/SSI compatible) connects easily to microcontrollers and DSPs. Micropower consumption at the full 100 kSPS data rate makes it one of the few 16-bit ADCs viable for battery-operated high-temperature systems. Architecturally, the SAR core uses an internal sample-and-hold with capacitor DAC, providing deterministic conversion latency with no pipeline delay. Ensured specifications across the full -55C to +210C range - rather than the -40C to +125C industrial limit of standard parts - distinguish the -HT grade, enabled by TI's high-temperature qualification flow and hermetic ceramic packaging that resists long-term thermal stress. Typical applications include downhole drilling telemetry, jet-engine and geothermal sensing, industrial process monitoring near furnaces, and aerospace instrumentation, where silicon reliability above 150C is mandatory and power budgets are tight. Design tip: decouple VCC and REF carefully at 210C, since reference noise directly scales with the reduced full-scale range; use low-ESR ceramic capacitors rated for the temperature and keep the serial clock lines short to preserve 16-bit noise performance.

RFQ پەیوەندی
ADS8320E/2K5 - 16-Bit 100kHz SAR ADC | Texas Instruments
ADS8320E/2K5

ADS8320E/2K5 - 16-Bit 100kHz SAR ADC | Texas Instruments

The Texas Instruments ADS8320E/2K5 is a 16-bit, 100-kHz sampling analog-to-digital converter in an 8-pin VSSOP package. The manufacturer specifies ensured operation over a 2.7 V to 5.25 V supply range and describes operation from 2 V to 5.25 V, with a synchronous serial interface compatible with SPI/SSI, a differential input, and a reference adjustable from 500 mV to VCC. Its low power consumption makes it suitable for portable and battery-operated measurement systems. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous voltage and produces a corresponding numeric code. This ADS8320 belongs to the SAR ADC family, in which a successive-approximation conversion cycle progressively resolves the input voltage. Compared with flash, pipeline, and sigma-delta architectures, SAR ADCs are commonly selected for moderate resolution, compact implementation, low power, and direct sequential data output. The headline characteristics are 16-bit resolution, a 100-kHz sampling rate, and operation from 2.7 V to 5.25 V. The device uses one SAR input, offers a differential input, and can operate with very little power even at the full 100-kHz data rate. A 3-uA maximum power-down current further supports low-duty-cycle acquisition. Its synchronous serial interface simplifies connection to microcontrollers and dedicated digital controllers while supporting SPI/SSI-compatible signaling. The reference-voltage arrangement provides another key design dimension: TI states that the reference can be set to any level from 500 mV to VCC. Full-scale accuracy therefore depends not only on the ADC but also on reference quality, analog front-end conditioning, source impedance, and printed-board contamination. Designers must preserve the differential input topology and account for acquisition time when planning conversion timing around the 100-kHz maximum data rate. Typical uses include battery-powered instrumentation, portable industrial sensors, process monitoring, low-energy edge acquisition, and embedded measurement systems. The VSSOP package reduces board area, but analog layout still requires a quiet reference, controlled return paths, and decoupling close to the supply pins. The device is best suited to applications whose required bandwidth is within the SAR ADC's 100-kHz sampling capability and whose dynamic range benefits from a 16-bit result. For implementation, verify the complete pinout and timing values in the manufacturer datasheet rather than inferring them from the VSSOP outline. Keep the analog input path short, place bypass capacitors close to the device, and avoid routing digital clock and serial-data traces beneath sensitive analog nodes. Validate gain, offset, and noise performance with the intended source impedance and reference implementation. This product page combines the verified TI product information, manufacturer datasheet link, distributor references, package information, and practical engineering guidance. It is intended to help engineers identify whether the ADS8320E/2K5 fits a low-power, 16-bit SAR measurement design before purchasing or committing to a PCB layout.

RFQ پەیوەندی
ADS8322Y/2K - 16-Bit 500kSPS SAR ADC | Texas Instruments
ADS8322Y/2K

ADS8322Y/2K - 16-Bit 500kSPS SAR ADC | Texas Instruments

The Texas Instruments ADS8322Y/2K is a 16-bit, 500 kSPS unipolar successive-approximation analog-to-digital converter in a 32-pin TQFP package. It includes an internal 2.5 V reference and an inherent sample-and-hold input, providing a compact single-channel conversion solution for industrial data-acquisition systems. An ADC is a data-conversion IC that transforms an analog voltage into a digital code. The ADS8322 belongs to the SAR ADC hierarchy, where a capacitor-based internal DAC successively compares a sampled input voltage with successive trial values. This architecture supports continuous conversion without the signal-processing latency associated with many delta-sigma converters, making the device suitable for measurement systems that require direct sampling and parallel digital output. The principal features include 16-bit resolution, a maximum sampling rate of 500 kSPS, a unipolar input range, an internal 2.5 V reference, and a full 16-bit parallel interface. An 8-bit read option is also available, allowing data to be transferred in two read cycles through eight interface pins. These features balance conversion resolution and throughput in a single 32-pin TQFP package. Internally, the ADS8322 uses a capacitor-based SAR register with an inherent sample-and-hold function. The converter can present conversion results through its complete 16-bit parallel interface or through the reduced 8-bit interface. Because the device is specified as a CMOS ADC and is offered in the industrial temperature range of -40 °C to +85 °C, it is suited to embedded industrial instrumentation where a predictable sampling rate and compact parallel interface are valuable. Typical applications include industrial process monitoring, sensor signal acquisition, laboratory measurement equipment, factory automation, power-system instrumentation, and embedded control systems. Its 500 kSPS rate supports acquisition of rapidly changing analog quantities, while the 16-bit code width provides finer numerical resolution than conventional lower-resolution SAR converters. PCB design should preserve the relationship between the analog input, reference circuitry, supply connections, and parallel data bus. Keep analog traces short, use a quiet ground return, and route the digital output bus away from the input node. Follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning tracks, terminating the interface, and selecting decoupling components. This page combines the official device characteristics with a package-aware comparison, practical PCB guidance, drop-in replacement screening, and application-focused design context. It is intended to accelerate component selection while keeping every proposed replacement tied to verified package and parameter requirements.

RFQ پەیوەندی
ADS8322YB/2KG4 - 16-Bit 500kSPS SAR ADC, 32-TQFP | Texas Instruments
ADS8322YB/2KG4

ADS8322YB/2KG4 - 16-Bit 500kSPS SAR ADC, 32-TQFP | Texas Instruments

The Texas Instruments ADS8322YB/2KG4 is a 16-bit, 500kSPS successive approximation register (SAR) analog-to-digital converter with an internal 2.5V reference, offered in a 32-pin TQFP (5x5 mm) package. It accepts a unipolar input range, draws low power at 500 kHz throughput, and provides either a full 16-bit parallel interface or an 8-bit mode using two read cycles across eight pins. A SAR ADC is a type of analog-to-digital converter that uses a binary search algorithm against an internal precision DAC to determine each bit sequentially within one conversion cycle. SAR ADCs sit in the signal chain between the analog front end (sensor, amplifier, anti-alias filter) and the digital controller (FPGA, MCU, DSP); they offer deterministic latency, no pipeline delay, and inherently good DC accuracy - making them the converter class of choice for multiplexed data acquisition, industrial control loops, and precision instrumentation. Key features of the ADS8322YB/2KG4 include a 16-bit capacitor-based SAR core with inherent sample-and-hold, an integrated 2.5V reference (eliminating an external reference IC and saving BOM cost), low power consumption at 500 kSPS throughput, and a parallel interface that supports either 16-bit or 8-bit bus mode. The /2K suffix indicates tape-and-reel packaging, while G4 denotes a Pb-free (lead-free) finish. Architecturally, the device combines a charge-redistribution DAC, a precision internal bandgap reference, and a successive-approximation register. The single 5V supply simplifies system power, and the high-speed parallel interface allows direct connection to FPGAs and DSPs without glue logic. Compared with pipelined ADCs of similar speed, the ADS8322 delivers better DC linearity for multiplexed-channel scanning because there is no pipeline latency to flush between conversions. Typical applications include data acquisition systems, industrial process control, optical networking power monitoring, portable instrumentation, and battery-powered test equipment. Designers also use the part in precision weigh scales, medical patient monitoring front ends, and motor-control feedback loops. When designing with the ADS8322YB/2KG4, ensure the analog input is driven by a low-impedance buffer with sufficient bandwidth to settle within the acquisition window, and use a clean 5V analog supply well decoupled at the AVdd pin. The /2K G4 ordering code identifies lead-free tape-and-reel packaging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
ADS8323Y/2K - 16-Bit 500kSPS SAR ADC | Texas Instruments
ADS8323Y/2K

ADS8323Y/2K - 16-Bit 500kSPS SAR ADC | Texas Instruments

The Texas Instruments ADS8323Y/2K is a 16-bit, 500 kSPS pseudo-bipolar successive-approximation-register analog-to-digital converter with an internal 2.5 V reference and a 32-pin TQFP package. It supports a full 16-bit parallel interface as well as an 8-bit readout mode using two read cycles. The converter features inherent sample-and-hold, CMOS operation, and a specified temperature range of -40°C to +85°C. An SAR ADC is a sampling data-converter category that compares an input voltage against an internal DAC during successive conversion steps. It belongs to the broader analog-to-digital converter, data-converter, and semiconductor hierarchies. Compared with flash and pipeline ADCs, a SAR converter generally combines moderate conversion speed with compact circuitry, deterministic sampling, and a direct parallel digital interface. The ADS8323 is designed for systems that require more precision than a typical 12-bit converter without moving to a substantially higher-speed converter architecture. Three defining features are its 16-bit resolution, 500 kSPS sampling rate, and internal 2.5 V reference. The pseudo-bipolar input arrangement supports acquisition of bipolar analog signals, while the internal reference reduces the number of external precision components required. The reported 0.0122% linearity error indicates that the converter is suitable for precision measurement systems requiring substantially more resolution than general-purpose instrumentation. Its parallel interface also allows complete 16-bit data to be captured efficiently by suitable digital control logic. Internally, the ADS8323 uses a capacitor-based 16-bit SAR core with an inherent sample-and-hold function. Conversion is performed through successive comparison steps, after which the selected digital code is presented through the parallel output interface. The manufacturer supports both full 16-bit operation and an 8-bit interface mode in which data are retrieved over two read cycles. This flexibility can simplify bus-width constraints in embedded control systems while retaining access to the converter's full resolution. Typical uses include industrial process measurement, factory automation, portable instrumentation, embedded sensor acquisition, data acquisition systems, and test and measurement equipment. Its 500 kSPS throughput supports sampling of rapidly changing sensor outputs, while 16-bit resolution preserves low-level analog information. In a complete measurement chain, the ADC can digitize conditioned outputs from pressure, temperature, current, and position sensors. Designers should preserve the analog input, reference, and digital return paths specified by the manufacturer datasheet. The parallel bus requires adequate signal-integrity margin for the intended clock rate and board topology. Input filtering, acquisition timing, and output settling also determine practical system accuracy and should be evaluated together rather than treating the converter's nominal resolution as the complete measurement accuracy. This product page combines the device's principal electrical characteristics, interface options, application guidance, and verified drop-in comparisons. It also distinguishes true engineering alternatives from simple reel or packing-code variations, helping designers select a replacement while preserving the TQFP-32 footprint and parallel-interface architecture.

RFQ پەیوەندی
ADS8324EB/250G4 - 14-Bit 50kSPS ADC 1.8V | Texas Instruments
ADS8324EB/250G4

ADS8324EB/250G4 - 14-Bit 50kSPS ADC 1.8V | Texas Instruments

The Texas Instruments ADS8324EB/250G4 is a 14-bit, 50-kSPS, 1.8-V micropower sampling analog-to-digital converter (ADC) housed in an 8-pin MSOP (PowerPAD) package. It features a synchronous SPI/SSI-compatible serial interface, a differential analog input, and an internal reference that can be set to any level from 500 mV to VCC/2. The /250G4 suffix indicates 250-piece tape-and-reel packaging with green/RoHS compliance and is pin-compatible with the older ADS7817 family. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts real-world analog voltages into discrete digital codes, sitting within the data-converter hierarchy of signal chain ICs (sensor -> amplifier -> ADC -> digital processor). Successive-approximation-register (SAR) ADCs like the ADS8324 achieve deterministic latency, low power, and high DC accuracy - ideal for multiplexed low-frequency precision measurements where battery life and small board area matter as much as raw speed. Key specifications include 14-bit resolution with no missing codes, 50 kSPS maximum throughput, 1.8 V single-supply operation, a 3-microamp maximum power-down current, and a 2.7 mA typical active current. The bipolar differential input accepts input ranges up to ±VREF, where the internal reference supports 500 mV to VCC/2. The serial interface uses an external clock for SAR conversions and outputs MSB-first data with a 2-state flag bit. Architecturally, the converter combines a charge-redistribution SAR core with an internal reference buffer, auto-power-down between conversions, and a daisy-chainable serial output. The device's 1.8 V supply and 3-microamp power-down current make it a benchmark for battery-powered precision instrumentation where every microwatt of quiescent draw matters. Typical applications include portable and battery-operated data loggers, remote sensor modules, isolated data acquisition front-ends, simultaneous multi-channel systems, handheld instrumentation, and GPS accessory modules. Its pin-compatibility with the ADS7817 family allows drop-in upgrade of legacy 12-bit designs to 14-bit resolution without PCB rework. When designing with the ADS8324, decouple VCC with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin and provide a 10 µF bulk capacitor on the reference pin. The CONVST signal must be clean; route DCLK and DOUT as 50-ohm-controlled traces and ensure the CS/DOUT timing satisfies the t_CNV and t_CK specifications. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes that complement the manufacturer datasheet for engineers evaluating the ADS8324EB/250G4 for new designs or as a second-source qualification candidate.

RFQ پەیوەندی
ADS8327IPW - 16-Bit 500kSPS SAR ADC | Texas Instruments
ADS8327IPW

ADS8327IPW - 16-Bit 500kSPS SAR ADC | Texas Instruments

Texas Instruments ADS8327IPW is a 16-bit, 500-kSPS, single-input unipolar SAR analog-to-digital converter operating from 2.7 V to 5.5 V in a 16-pin TSSOP package. The converter combines a capacitor-based 16-bit successive-approximation register with an inherent sample-and-hold circuit and a high-speed, wide-voltage serial interface. An ADC converts a continuous analog voltage into a numeric code for measurement, control, or communication. The ADS8327 belongs to the SAR ADC family within the broader data-converter and signal-processing hierarchy. SAR conversion repeatedly compares the sampled input with internal references and applies successive bit decisions. This architecture is well suited to instrumentation, industrial control, and embedded systems that require deterministic sampling without the complexity of a continuously operating conversion engine. The ADS8327 accepts a unipolar input and provides a nominal conversion rate of 500 kSPS. Its 2.7 V to 5.5 V analog and digital supply range supports both 3.3 V and 5 V systems. The device also includes a serial interface suitable for connecting to embedded processors, field-programmable logic, or data-acquisition controllers. These characteristics make the ADS8327 useful when design priority is placed on resolution, throughput, compact packaging, and straightforward serial integration. Internally, the ADS8327 uses a 16-bit capacitor-based SAR converter with an inherent sample-and-hold function. This supports repeatable sampled measurement while freeing the host processor to handle filtering, scaling, calibration, and data transfer. The serial output reduces the number of parallel signal lines needed on compact boards, while the 16-pin TSSOP package simplifies assembly in conventional surface-mount production processes. Typical applications include precision analog measurement, industrial sensor acquisition, process-control loops, laboratory instrumentation, and embedded data loggers. In a sensor interface, the ADC can digitize the output of a conditioned transducer before the controller evaluates thresholds or performs control calculations. In an industrial system, its 500-kSPS capability can accommodate fast measurement loops, provided that the front-end settling time and acquisition timing are designed correctly. A critical design consideration is the relationship among input bandwidth, acquisition time, conversion time, and source impedance. The active front-end should settle the sampling capacitor within the converter's acquisition interval, and the analog input must remain within the specified operating range. Reference and supply bypass placement close to the device also helps preserve measurement repeatability. Use the manufacturer pin-description table and timing diagrams when assigning PCB nets and calculating sampling-cycle timing. This page combines the manufacturer's principal ADC specifications, sourcing guidance, package information, replacement analysis, and practical design notes. It also distinguishes verified drop-in choices from options that require a different footprint, interface review, or changed supply arrangement, helping engineers make a controlled redesign rather than relying only on nominal resolution and speed.

RFQ پەیوەندی
ADS8328IRSAR - 16-Bit 500kSPS 2-Channel SAR ADC | Texas Instruments
ADS8328IRSAR

ADS8328IRSAR - 16-Bit 500kSPS 2-Channel SAR ADC | Texas Instruments

The Texas Instruments ADS8328IRSAR is a 16-bit, 500-kSPS, low-power successive-approximation-register (SAR) analog-to-digital converter with a 2-to-1 input multiplexer, offered in a 16-pin VQFN (RSA) package with exposed thermal pad. It operates from a single analog supply of 2.7 V to 5.5 V and a digital I/O supply of 1.65 V to 5.5 V, drawing only 10 mW at full throughput. The device integrates a high-speed synchronous serial interface compatible with DSP, SPI, and frame-sync protocols, and supports chain-mode daisy-chaining of multiple converters. An SAR ADC (successive-approximation-register analog-to-digital converter) is a sampled-data converter class that resolves N bits in N clock cycles by switching a binary-weighted capacitor DAC against the input. SAR ADCs occupy the middle ground between flash converters (fastest, lowest resolution) and sigma-delta (highest resolution, slowest). The ADS8328 belongs to the precision-signal-chain IC family, sitting under data converters (ADC/DAC) in the broader signal-chain taxonomy, with a single +5 V analog supply as its typical operating rail. Key features include ±0.5 LSB typical INL and ±0.5 LSB typical DNL, a 2-to-1 input MUX with programmable TAG-bit output for channel identification, and 1.636 µs typical conversion time. The device also offers a flexible power-down state that reduces supply current to <1 µA between conversions, plus an offset-calibration command and an internal 20 MHz serial clock. The wide digital I/O range (1.65 V to 5.5 V) allows direct interfacing to 1.8 V, 3.3 V, and 5 V microcontrollers and DSPs without level shifters. Architecturally, the ADS8328IRSAR uses a charge-redistribution capacitor DAC with inherent sample-and-hold, which preserves the input signal during the conversion window and supports takt-manager placement of the input capacitor on each channel. The 2:1 MUX and TAG bit allow multi-channel data acquisition on a single serial bus, while chain-mode operation lets up to 16 devices share one CS line for 32-channel systems. Typical applications include portable industrial data loggers, multi-channel battery-pack monitors, optical-module photodiode readout, medical instrumentation signal chains, and precision sensor front ends. The wide analog supply tolerance makes it suitable for both 3.3 V and 5 V designs. When designing with this device, ensure adequate input bandwidth and use a low-impedance input buffer when driving from high-impedance sensors. The serial interface clock can be sourced from the host or generated by the ADC's internal oscillator. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
ADS8329IPW - 16-Bit 1-MSPS SAR ADC | Texas Instruments
ADS8329IPW

ADS8329IPW - 16-Bit 1-MSPS SAR ADC | Texas Instruments

The Texas Instruments ADS8329IPW is a low-power, 16-bit, 1-MSPS successive-approximation analog-to-digital converter with a unipolar input, operating from a 2.7 V to 5.5 V supply. The device is packaged in a 16-pin TSSOP and is intended for precision signal-acquisition systems that require accurate conversion at a relatively high sampling rate. Its serial interface reduces the number of external signal connections and supports compact, high-density instrument designs. An ADC is an interface IC that converts an analog voltage into a digital code for processing by a microcontroller, DSP, FPGA, or other digital controller. The ADS8329 belongs to the successive-approximation, or SAR, ADC family. SAR ADCs use a capacitor-based internal sampling network and compare the sampled input against an internal reference, producing a deterministic conversion result without the complexity of a pipeline converter. This makes the ADS8329 suitable for industrial measurement, data acquisition, and precision control systems. Key features include 16-bit resolution, a 1-MSPS conversion rate, a 2.7 V to 5.5 V analog supply range, and a single unipolar analog input. The capacitor-based SAR core includes an inherent sample-and-hold function. A high-speed, wide-voltage serial interface allows the converter to communicate efficiently with digital control logic while limiting PCB pin count and signal-routing complexity compared with a parallel ADC. The ADS8329 is optimized for low-power operation and unipolar input measurement. Because the converter is based on a SAR architecture, it can complete successive comparison cycles at 1 MSPS while providing the accuracy and linearity expected from a 16-bit converter. The serial interface is especially useful when the ADC is located near an analog sensor and the resulting digital data must be transferred over a limited number of PCB traces. Typical applications include industrial process monitoring, portable instrumentation, sensor-interface modules, test and measurement equipment, and embedded control systems. The unipolar input arrangement is well suited to sensors whose output remains between ground and the positive analog supply range. Systems requiring two analog channels may evaluate the ADS8330, which uses the same converter core and adds a two-to-one input multiplexer, although board compatibility should be confirmed from the device pinouts before substitution. For reliable operation, the analog and digital sections should be laid out according to the manufacturer datasheet, with clean reference connections, short return paths, and adequate bypassing near the supply pins. The serial interface timing, conversion trigger sequence, input range, and reference configuration must also be implemented exactly as described in the datasheet. These measures are particularly important because reference and layout errors can consume more of the available measurement accuracy than the nominal ADC resolution. This product page brings together the converter's principal operating parameters, package information, practical application guidance, selection criteria, and a qualified comparison framework. It also distinguishes the direct ADS8329 configuration from the multiplexed ADS8330 so engineers can assess channel requirements, interface behavior, and PCB compatibility before finalizing a design.

RFQ پەیوەندی
ADS8341E - 16-Bit 4-Channel 100kHz ADC | Texas Instruments
ADS8341E

ADS8341E - 16-Bit 4-Channel 100kHz ADC | Texas Instruments

The Texas Instruments ADS8341E is a 16-bit, 4-channel serial-output sampling analog-to-digital converter with a 100 kHz conversion rate, 86 dB SINAD, and an SSOP-16 package. The device accepts four single-ended inputs or two differential inputs and uses a synchronous serial interface for data transfer. It is also identified as pin-for-pin compatible with the ADS7841, providing a defined migration path for existing designs. A sampling ADC is a data-acquisition semiconductor that converts an analog voltage into a digital value through a sample-and-hold stage and successive-approximation conversion. The ADS8341E belongs to the ADC > data converter > signal-chain IC hierarchy. Its onboard input multiplexer reduces the number of external analog switches required, while its synchronous serial interface supports economical connections to microcontrollers, digital signal processors, and isolated data-acquisition systems. The principal specifications include 16-bit resolution, four single-ended or two differential input channels, and a maximum stated conversion rate of 100 kHz. The manufacturer data reports 86 dB SINAD for signal-quality evaluation. Typical power dissipation is approximately 8 mW when operating at the 100 kHz throughput rate with a 5 V supply, making the device suitable for portable and battery-operated instrumentation where conversion speed, channel count, and power must be balanced. Technically, the ADS8341E combines an input multiplexer, sample-and-hold circuitry, a 16-bit successive-approximation ADC, and a synchronous serial output stage in one package. This integration simplifies analog channel selection and digital data acquisition. The serial interface can also reduce the number of interconnections required to reach a remote or isolated acquisition boundary, although the complete system still requires an appropriate reference, source impedance, layout, and digital interface implementation. Typical applications include personal digital assistants, portable multichannel data loggers, measurement equipment, industrial process monitoring, and low-cost isolated remote data-acquisition systems. Its four-channel architecture is especially useful when several slowly varying analog sensors must share one converter, while the 100 kHz conversion capability supports higher-rate instrumentation than a slow general-purpose ADC. Designers should account for the 5 V operating condition cited for the typical 8 mW power figure, provide suitable analog and reference bypassing, and keep sensitive input and reference traces short. Before replacing another converter, verify the complete pinout and serial protocol rather than relying only on package similarity. The published ADS7841 compatibility is a useful starting point, but PCB changes require confirmation against the manufacturer data.

RFQ پەیوەندی
ADS8341EB - 16-Bit 4-Channel 100 kHz ADC | Texas Instruments
ADS8341EB

ADS8341EB - 16-Bit 4-Channel 100 kHz ADC | Texas Instruments

Texas Instruments ADS8341EB is a 16-bit, 4-channel serial-output sampling analog-to-digital converter with a maximum conversion rate of 100 kHz, configured for either four single-ended or two differential inputs. It is packaged in a 16-pin SSOP and operates from a 2.7 V to 5 V supply range. The converter delivers 86 dB SINAD and 0.0092% linearity error for precision signal-acquisition systems. A sampling ADC is a semiconductor that samples an analog voltage at a controlled interval and converts each sample into a digital code. The ADS8341 belongs to the SAR ADC family, where a successive-approximation conversion architecture produces a digital result through a sequence of internal comparisons. Its serial interface integrates directly with microcontrollers, DSPs, and programmable logic while minimizing external data-bus wiring. The four input channels can be arranged as four single-ended inputs or two differential inputs. This flexibility supports sensor interfaces, process-control instrumentation, and measurement systems in which common-mode noise rejection is important. The 100 kHz conversion rate provides sufficient throughput for many industrial, communications, and control applications, while 16-bit resolution preserves fine detail in slow or precision-oriented measurements. According to the Texas Instruments product documentation, typical power dissipation is 8 mW with a 5 V supply at a 100 kHz throughput rate. The device uses a synchronous serial interface, allowing conversion data to be transferred in a predictable clocked sequence. Its 86 dB SINAD specification quantifies signal-to-noise plus distortion performance and is the key figure for assessing usable conversion accuracy in the intended analog bandwidth. Typical applications include factory process monitoring, portable measurement equipment, industrial data acquisition, and embedded sensor conditioning. Differential operation is particularly useful when the source is centered around a common-mode voltage or when cable noise could otherwise influence the measurement. The low power consumption also suits compact systems in which converter throughput must be balanced against thermal and battery requirements. Design the input network so that source impedance, settling time, and the acquisition interval meet the converter’s sampling requirements. Use a stable reference voltage, place input and reference decoupling capacitors close to their pins, and route the serial clock and data signals away from noisy switching nodes. Confirm timing for CS, SCLK, and data-valid signals against the interface timing in the manufacturer datasheet. This page consolidates the key electrical limits, channel configurations, package information, interface considerations, and drop-in replacement guidance for the ADS8341EB. It also adds practical selection and PCB guidance so engineers can evaluate the converter alongside pin-compatible family options before committing to a design.

RFQ پەیوەندی
ADS8342IBPFBR - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments
ADS8342IBPFBR

ADS8342IBPFBR - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments

The Texas Instruments ADS8342IBPFBR is a 16-bit, 4-channel, parallel-output successive approximation register (SAR) analog-to-digital converter sampling at up to 250 kSPS while dissipating only 200 mW from a ±5 V supply. Housed in a TQFP-48 (PFB) package with industrial -40°C to +85°C operation, this ADC combines a true-bipolar 4-channel input multiplexer with an inherent sample-and-hold and 16-bit ensured no-missing-codes performance. A SAR ADC is a successive-approximation-register analog-to-digital converter that uses an internal capacitive DAC and comparator to perform a binary search across the input voltage each conversion cycle. SAR ADCs excel at medium-resolution, medium-speed precision measurements because they are deterministic in latency, free of pipeline delay, and exhibit excellent DC linearity, making them the standard choice for multiplexed data-acquisition systems, industrial process control, and precision instrumentation where one sample per channel per cycle is acceptable. Key features include true bipolar input signal range on each of the four channels (selectable ±VREF input spans), 1 mV max channel offset, integrated 4-to-1 analog multiplexer with channel-by-channel conversion, parallel 3-state output drivers for direct microprocessor interface, and a hardware-triggered conversion start. The capacitive-DAC SAR core achieves ±4 LSB maximum INL at the I-grade and ±6 LSB at the standard grade, ensuring monotonic 16-bit performance across the full industrial temperature range. Architecturally, the ADS8342 pairs a binary-weighted capacitor DAC array with a low-noise comparator and on-chip reference buffer, while a state-machine controller sequences acquisition, conversion, and output. The wide bipolar input range eliminates front-end signal conditioning for many industrial sensors, and the 250 kSPS aggregate throughput lets one ADC service up to four sensors without additional switching. The 3-state parallel bus simplifies connection to FPGAs, DSPs, and microprocessors, while the synchronous /CS and BUSY handshake makes system integration straightforward. Typical applications include multi-channel data acquisition systems, industrial process control front ends, precision instrumentation, weigh scales and load-cell digitizers, and portable or battery-powered measurement equipment. Designers select the ADS8342 when they need guaranteed 16-bit no-missing-codes performance, true bipolar inputs on multiple channels, and parallel-interface simplicity without an integrated PGA. When designing with this part, ensure the analog input is bandwidth-limited well below the Nyquist rate and that the external reference is low-noise and well-decoupled to preserve the 16-bit DC accuracy. The /BUSY output must be monitored by the host to avoid bus contention during conversion, and the analog supply must be heavily bypassed with both bulk and ceramic capacitors placed close to the AVDD pin. This page synthesizes real-time distributor pricing from DigiKey and Mouser, drop-in alternative guidance from TI's cross-reference catalog, and practical PCB-layout / reference-decoupling notes that engineers need but that the bare manufacturer datasheet does not consolidate in one place.

RFQ پەیوەندی
ADS8342IPFBR - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments
ADS8342IPFBR

ADS8342IPFBR - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments

The Texas Instruments ADS8342IPFBR is a 16-bit, 4-channel, 250 kSPS successive-approximation-register (SAR) analog-to-digital converter with a parallel output interface, supplied in a 48-pin TQFP (PFB) package. The device accepts 4 true-bipolar input channels, dissipates approximately 200 mW from ±5 V analog and +5 V digital supplies, and is specified for the industrial -40 °C to +85 °C temperature range. Key headline specifications include 16-bit no-missing-code resolution, 250 kSPS throughput, 34 µs maximum conversion time, and a 1 mV maximum offset error. A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that performs a binary search against the analog input using an internal DAC and comparator, producing one bit per clock cycle. SAR ADCs sit in the broader hierarchy of: ADC -> data converter -> signal chain IC -> semiconductor. Compared with delta-sigma and pipeline ADCs, SAR architectures offer deterministic latency, low latency-to-resolution trade-offs, and excellent DC accuracy without requiring complex anti-alias filtering, which is why they dominate multiplexed industrial acquisition, instrumentation, and motor-control front-ends. Differentiating features of the ADS8342IPFBR include a 4-channel true-bipolar input multiplexer with software-configurable unipolar or bipolar ranges, an internal sample-and-hold, a 16-bit guaranteed-no-missing-codes parallel interface, and 3-state driver outputs that connect directly to a microprocessor data bus. The converter requires an external reference voltage of typically +2.5 V and a 5 MHz external clock. Per the TI ADS8342 datasheet (SBAS277, dated May 2003), the device achieves 0.0092 % maximum linearity error and 87 dB typical SNR at 10 kHz input. The SAR architecture combined with the capacitor-based DAC delivers low aperture uncertainty and fast acquisition, making the device well suited to multiplexed multi-channel data-acquisition systems where sequential channel switching is required. The parallel 16-bit output minimizes host CPU overhead compared with serial-output ADCs, and the 3-state outputs simplify bus-sharing with memory or other peripherals. Typical applications include multi-channel data-acquisition systems (DAQ), industrial process-control front-ends, portable instrumentation, medical monitoring equipment, and precision sensor signal conditioning. The wide bipolar input range allows direct connection to ±5 V or ±10 V transducer outputs after simple external resistor scaling. The 48-pin TQFP package provides easy board assembly in moderate-density designs. When designing with this part, place the external 2.5 V reference and reference decoupling capacitors as close to the REF pin as possible, and provide a low-impedance analog ground plane to minimize conversion noise. For best DC linearity, use 1 % or better external input scaling resistors and ensure the CLK input has a clean 50 % duty-cycle source. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design guidance beyond what is shown in the TI datasheet alone.

RFQ پەیوەندی
ADS8342IPFBRG4 - 16-Bit 250kSPS 4-Ch Bipolar ADC | Texas Instruments
ADS8342IPFBRG4

ADS8342IPFBRG4 - 16-Bit 250kSPS 4-Ch Bipolar ADC | Texas Instruments

The Texas Instruments ADS8342IPFBRG4 is a 16-bit, 250 kSPS, 4-channel, true-bipolar analog-to-digital converter (ADC) with a parallel output interface, packaged in a 48-pin TQFP (PFB). It accepts four true bipolar input channels and provides a parallel interface selectable between 8-bit and 16-bit bus modes for direct connection to microprocessors, microcontrollers, and DSPs. Sampling at up to 250 kSPS while drawing only 200 mW from a ±5 V analog supply, the ADS8342IPFBRG4 fits between slow precision converters and high-speed unipolar ADCs in cost-sensitive industrial data-acquisition front-ends. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples a continuous analog input voltage and produces a discrete digital code proportional to the input. The ADS8342IPFBRG4 is a successive-approximation-register (SAR) ADC, which uses a capacitor-based charge-redistribution digital-to-analog converter (CDAC) and an internal sample-and-hold to acquire the input in a single conversion cycle per channel. Within the broader taxonomy, the ADS8342IPFBRG4 sits at: ADC -> SAR ADC -> bipolar-input ADC -> parallel-output ADC -> data-acquisition IC -> semiconductor IC. This positioning determines its ideal use cases versus sigma-delta ADCs (higher resolution, lower speed), pipeline ADCs (faster, unipolar), and integrating ADCs (slowest, highest noise rejection). Key features include 16-bit no-missing-codes guaranteed performance, four true bipolar input channels (±VREF range per channel) selected by an internal multiplexer, low input-referred offset (1 mV max), selectable 8-bit / 16-bit parallel interface, single-ended analog supply operation from a ±5 V split (or 5 V single with proper input conditioning), low 200 mW power dissipation, and a TQFP-48 surface-mount package rated for -40 °C to +85 °C industrial operating range. The suffix -RG4 indicates reel-packaging tape-and-reel with lead-free terminations. Internally, the ADS8342IPFBRG4 combines a low-noise reference buffer, a high-impedance input multiplexer, a charge-redistribution 16-bit SAR core, and a 3-state parallel output driver. The bipolar input structure is implemented with a front-end analog level-shifter, allowing each channel to digitize voltages that cross the analog ground rail, which is essential when measuring transducer outputs that swing above and below 0 V. Typical applications include industrial process-control instrumentation, multi-channel data-acquisition systems (DAQs), test and measurement equipment front-ends, medical instrumentation signal conditioning, and factory-automation analog input modules. Each of these scenarios benefits from the 4-channel input multiplexer that reduces system cost by eliminating external channel-switching components. When designing with this device, pay attention to analog supply decoupling, keep digital return currents separate from analog grounds, and provide adequate reference bypassing. A low-noise external reference is critical for achieving 16-bit performance; using the on-chip reference or a noisy supply reference will degrade SNR and integral nonlinearity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineering value beyond what DigiKey or Mouser product pages offer.

RFQ پەیوەندی
ADS8342IPFBTG4 - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments
ADS8342IPFBTG4

ADS8342IPFBTG4 - 16-Bit 250kSPS 4-Ch SAR ADC | Texas Instruments

The Texas Instruments ADS8342IPFBTG4 is a 16-bit, 250-kSPS, 4-channel successive-approximation analog-to-digital converter (SAR ADC) with true bipolar input channels and a parallel 3-state output interface, housed in a 48-pin TQFP (PFB) package. It integrates a precision 16-bit SAR core, a capacitor-based DAC, an inherent sample-and-hold circuit, 4-channel input multiplexer, and parallel microprocessor-compatible drivers, all specified at 250 kHz while dissipating only 200 mW from a ±5 V analog supply. A SAR ADC is a successive-approximation analog-to-digital converter that uses a comparator, successive-approximation register, and an internal DAC to convert analog signals one bit at a time over N conversion cycles. SAR ADCs offer deterministic latency, no pipeline delay, excellent DC accuracy, and are widely used in industrial automation, instrumentation, data acquisition, and process control where multi-channel sampling and bipolar signal handling are required. Key features include 4 true bipolar input channels with software-selectable input ranges (±10 V, ±5 V, 0 V to 10 V, 0 V to 5 V per channel), 16-bit no-missing-codes guaranteed performance, low 1 mV max offset error, 250 kSPS throughput, and a low-power 200 mW typical dissipation. The parallel interface provides direct connection to microprocessors, microcontrollers, and DSPs without glue logic. Internally, the ADS8342 uses a charge-redistribution capacitor DAC for accurate successive approximation, with integrated input signal conditioning and reference buffering. The architecture delivers low aperture jitter and deterministic conversion timing, making the device suitable for multiplexed multi-channel data acquisition where per-channel DC accuracy must be preserved across rapid channel switching. Typical applications include industrial process control and PLC analog input modules, multi-channel data acquisition systems, medical instrumentation front-ends, test and measurement equipment, and high-accuracy multi-axis sensor monitoring. The true bipolar input capability eliminates the need for external signal conditioning on ±10 V or ±5 V transducer outputs. When designing with the ADS8342, ensure that the analog (AVDD) and digital (DVDD) supplies are well decoupled, and that the external reference is low-impedance and well bypassed at the REF pin. For multi-channel systems, the input multiplexer settling time should be considered when channel switching at full throughput to preserve channel-to-channel accuracy. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes that complement the manufacturer datasheet.

RFQ پەیوەندی
ADS8343E - 16-Bit, 4-Channel ADC | Texas Instruments
ADS8343E

ADS8343E - 16-Bit, 4-Channel ADC | Texas Instruments

Texas Instruments ADS8343E is a 16-bit, 4-channel sampling analog-to-digital converter with a 100 kSPS conversion rate in a 16-pin SSOP package. It accepts four single-ended inputs or two differential inputs, supports a bipolar input range, and operates from a 2.7 V to 5.25 V single supply. The device is designed for precision multichannel measurement where accurate conversion, flexible input configuration, and a serial data interface are required. A sampling ADC is a data-converter category that uses a sample-and-hold circuit and successive-approximation conversion to translate an analog voltage into a digital code. Within the broader semiconductor hierarchy, the ADS8343E belongs to the ADC and DAC family of data-converter integrated circuits. Its onboard input multiplexer reduces the need for separate analog switching when several sensors or measurement nodes must be digitized by one converter. The ADS8343E provides 86 dB SINAD at a 100 kSPS throughput rate and accepts bipolar input signals. Its reference voltage can be adjusted from 500 mV to VCC/2, providing a corresponding input range of ±VREF. The serial interface also supports economical galvanic isolation when the converter is placed on the isolated side of a measurement system. A shutdown mode reduces power dissipation when conversion is not required. Typical power dissipation is 8 mW at 100 kSPS with a 5 V supply, making the converter suitable for portable and battery-operated instrumentation. The operating temperature range is −40 °C to +85 °C. Unlike flash or pipeline ADCs, this successive-approximation sampling architecture combines low power, compactness, and a straightforward serial interface for low-rate, high-resolution measurements. The ADS8343E is well suited to portable data loggers, personal digital assistant equipment, multichannel measurement instruments, isolated remote data-acquisition systems, sensor-interface circuits, and industrial process-monitoring equipment. Four multiplexed channels allow one converter to service several analog sources while reducing converter count, board area, and data-acquisition system complexity. When designing around the ADS8343E, select the external reference carefully because VREF determines the bipolar input span. Preserve the supply and reference bypass-capacitor placement recommended by the manufacturer datasheet, and treat the serial interface timing and digital return path as part of the analog measurement design. The serial interface can provide low-cost isolation, but grounding and interface isolation must be planned around the complete measurement chain. This product page consolidates the key ADC specifications, pin-compatible alternatives, comparative parameters, and practical design guidance into one engineering-focused reference. It supports faster component selection while preserving the distinction between exact ordering variants, pin-compatible family options, and application-level trade-offs.

RFQ پەیوەندی
ADS8343EB - 16-Bit 4-Channel ADC | Texas Instruments
ADS8343EB

ADS8343EB - 16-Bit 4-Channel ADC | Texas Instruments

The Texas Instruments ADS8343EB is a 16-bit, four-channel serial-output sampling analog-to-digital converter with a 100 kHz conversion rate, 86 dB SINAD, and an SSOP-16 package. It supports four single-ended inputs or two differential inputs, operates from a single supply, and uses a synchronous serial interface for compact data acquisition systems. A sampling ADC is a category of analog-to-digital converter that samples an analog input and converts each sample into a digital code. The ADS8343 belongs to the sampling ADC hierarchy within data-converter ICs, where its onboard multiplexer selects among analog channels before conversion. Its four-channel architecture reduces the need for external analog switches in portable instruments, battery-powered recorders, and remote measurement equipment. The principal features include 16-bit resolution, four selectable analog inputs, differential or single-ended operation, a 100 kHz conversion rate, and 86 dB signal-to-noise-plus-distortion ratio. The reference voltage can range from 500 mV to half the supply voltage, while the corresponding bipolar input range is ±VREF. A shutdown mode further reduces consumption when acquisition is paused. Internally, the device uses a successive-approximation-register conversion architecture combined with an onboard multiplexer. Its synchronous serial interface supports communication with a compact embedded controller while enabling isolation between the analog front end and the digital control side. Typical power dissipation is 8 mW at a 100 kHz throughput rate with a 5 V supply, making the converter suitable for portable and battery-operated systems. Typical applications include portable multichannel data loggers, personal digital assistant equipment, precision measurement instruments, industrial panel meters, battery-powered environmental monitors, and remote data-acquisition nodes. The 100 kHz throughput supports continuous monitoring of several relatively slow-changing analog signals without requiring a fast external multiplexer. Designers should pay close attention to reference-voltage stability, input-range selection, source impedance, and the relationship between sample rate, signal bandwidth, and filter requirements. Place the reference and decoupling capacitors close to the associated pins, and route analog inputs away from high-current digital switching paths. The SSOP-16 footprint also requires careful assembly planning because its lead pitch is narrow. This product page combines the manufacturer’s electrical specifications with practical channel-selection, reference, layout, and replacement guidance. It also distinguishes true pin-compatible alternatives from converter families that require a different package or pin count, helping engineers evaluate migration paths without changing the PCB footprint.

RFQ پەیوەندی
ADS8343EB/2K5 - 16-Bit 4-Ch 100kHz SAR ADC | Texas Instruments
ADS8343EB/2K5

ADS8343EB/2K5 - 16-Bit 4-Ch 100kHz SAR ADC | Texas Instruments

The Texas Instruments ADS8343EB/2K5 is a 16-bit, 4-channel successive-approximation analog-to-digital converter (SAR ADC) with a synchronous serial interface, supplied in a 16-pin SSOP (DBQ) package and shipped on a 2,500-piece tape-and-reel. It samples at up to 100 kHz throughput from a single 2.7 V to 5 V supply, dissipating typically 8 mW at full speed, and offers 86 dB SINAD, bipolar input capability, and pin-for-pin compatibility with the legacy ADS7841 and ADS8341. A SAR ADC is a successive-approximation analog-to-digital converter that resolves one bit per internal clock cycle using a binary-search algorithm against a precision DAC and comparator. Within the data-converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, lowest bandwidth), making them the workhorse choice for multiplexed multi-channel 12-16 bit systems where deterministic latency, low power, and small package size matter more than maximum sample rate. The ADS8343 family is a textbook example of this class. Key features include 4 single-ended or 2 differential input channels routed through an on-chip analog multiplexer, an input range of 0 V to VREF (with bipolar input capability when VREF = VCC/2, giving ±VREF), a reference voltage from 500 mV to VCC, an 86 dB SINAD figure, a serial SPI/QSPI/MICROWIRE-compatible interface, and a hardware shutdown mode that drops quiescent current below 1 µA for battery-powered duty-cycled applications. The architecture uses a capacitive charge-redistribution DAC with a high-performance comparator and on-chip sample-and-hold. Conversion is initiated on the falling edge of CS, and 16 clocks later a full 16-bit word is clocked out on DOUT, giving deterministic latency useful for motor-control and multi-plexed data-acquisition loops. The wide 2.7 V-5 V supply range and bipolar input option make it equally comfortable in 3.3 V microcontroller and 5 V industrial signal chains. Typical applications include industrial process-control data acquisition, portable battery-powered instrumentation, touch-screen controllers (where the part is a pin-for-pin upgrade for ADS7841/ADS8341 designs), motor-control feedback, and multi-channel sensor-interface boards. Its shutdown mode makes it attractive for hand-held meters that spend most of their time asleep. When designing with the ADS8343, decouple VCC and VREF locally with 0.1 µF ceramics and add a 10 µF bulk capacitor, keep analog and digital grounds joined at a single star point, and avoid driving the analog inputs while CS is idle without a defined DC bias. The /2K5 suffix denotes the 2,500-unit tape-and-reel packaging option, so order the correct quantity break for your production line.

RFQ پەیوەندی
ADS8343EB/2K5G4 - 16-Bit 4-Ch 100kHz SAR ADC | Texas Instruments
ADS8343EB/2K5G4

ADS8343EB/2K5G4 - 16-Bit 4-Ch 100kHz SAR ADC | Texas Instruments

The Texas Instruments ADS8343EB/2K5G4 is a 16-bit, 4-channel, successive-approximation-register (SAR) analog-to-digital converter (ADC) with serial output, capable of up to 100 kHz conversion rate, housed in a 16-pin SSOP package. It features a bipolar input range, single supply operation from 2.7V to 5.25V, and 86 dB SINAD, making it suitable for precision data acquisition in industrial and instrumentation applications. The part is pin-for-pin compatible with the ADS7841 and ADS8341, simplifying upgrades in existing designs. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a precision data conversion device that uses a binary search algorithm to digitize analog inputs one bit at a time. SAR ADCs occupy a tier in the conversion hierarchy: ADC -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor. They are valued for high accuracy, low latency, deterministic sampling, and excellent DC linearity, making them preferable to delta-sigma ADCs in multiplexed multi-channel systems where per-channel throughput must be preserved. Key features of the ADS8343EB include 4 single-ended or 2 differential input channels, an SPI/QSPI/MICROWIRE-compatible serial interface, 86 dB SINAD, low power dissipation (typical 2.7 mW at 100 kHz with 5V supply), and a -40C to +85C industrial operating temperature range. The bipolar input range enables direct sampling of signals that swing around ground or operate from negative rails, removing the need for level-shifting front ends in many industrial control loops. Technically, the ADS8343EB uses a charge-redistribution DAC architecture with an internal sample-and-hold, a precision comparator, and an on-chip clock. Its 2's complement binary output format streamlines interfacing with both microcontrollers and digital signal processors. The /2K5G4 suffix indicates a 2,500-unit tape-and-reel packaging variant of the ADS8343EB, while the G4 suffix marks it as a Pb-free, RoHS-compliant, green-product release. Typical applications include industrial process control, portable instrumentation, battery-powered data loggers, isolated data acquisition front ends, and multi-channel sensor readback. The device's bipolar input and modest power budget also suit remote or loop-powered sensor nodes. When designing with this part, ensure the reference voltage source is low-noise and adequately decoupled, since reference noise couples directly into conversion results. The serial interface timing is straightforward, but the BUSY signal must be polled or used to gate SCLK correctly to avoid readback corruption.

RFQ پەیوەندی
ADS8344E - 16-Bit 100-kSPS 8-Channel SAR ADC | Texas Instruments
ADS8344E

ADS8344E - 16-Bit 100-kSPS 8-Channel SAR ADC | Texas Instruments

Texas Instruments ADS8344E is a 16-bit, 100-kSPS, 8-channel successive-approximation analog-to-digital converter with single-ended inputs, a synchronous serial interface, and a 20-SSOP package. It supports 8-channel single-ended or 4-channel differential operation, 84 dB SINAD, and a reference voltage adjustable from 500 mV to VCC. An SAR ADC is a sampling analog-to-digital converter that compares the input voltage with an internal DAC during successive clock cycles. Each cycle resolves one additional bit, allowing the ADS8344E to deliver 16-bit resolution at 100 kSPS. Its eight-channel input multiplexer makes it part of the ADC → data converter → mixed-signal acquisition hierarchy used for portable instruments, multichannel measurement systems, battery-operated data loggers, and isolated remote data-acquisition equipment. The principal features include eight single-ended inputs, support for four differential inputs, a 100-kSPS conversion rate, 84 dB signal-to-noise-plus-distortion, and a low-noise synchronous serial interface. The four-wire interface uses separate clock, data input, data output, and chip-select signals. According to the manufacturer datasheet, digital inputs are overvoltage tolerant to +5.5 V regardless of the +VCC supply, which simplifies mixed-voltage digital interfacing. Typical power dissipation is 10 mW when operating at the 100-kSPS throughput rate with a +5 V supply. The device also includes a shutdown mode that reduces power dissipation when conversion activity is not required. The external VREF may vary from 500 mV to VCC, with the corresponding input range extending from 0 V to VREF. This adjustable range allows the converter to use the full span of a system reference instead of accepting only a fixed full-scale input. The ADS8344E is suitable for portable data loggers, personal digital assistants, measurement equipment, and low-cost isolated remote data-acquisition systems. In a multichannel logger, its on-board multiplexer reduces the number of external analog switches, while the four-wire synchronous interface simplifies communication with a microprocessor or programmable controller. When designing the input network, preserve the relationship between VREF and the accepted analog range, account for input settling time between channel selections, and place reference and interface-trace capacitance close to the device. For isolated acquisition, place the serial interface across the isolation barrier and verify that the controller meets the input timing and logic-level requirements. This product record combines manufacturer specifications, distributor availability references, package information, and verified same-family alternatives. It also identifies the unresolved items that must be checked against current distributor pricing and the complete manufacturer datasheet before a production design is released.

RFQ پەیوەندی