ADC/DAC
بەرهەمەکان (3,600+)
ADV7393BCPZ-REEL - 10-Bit SD/HD Video Encoder, 40-LFCSP | ADI
The Analog Devices ADV7393BCPZ-REEL is a low-power, chip-scale 10-bit SD/HD video encoder that integrates three 10-bit video DACs and a digital video encoder on a single monolithic die. Housed in a 40-lead LFCSP-VQ (6x6 mm) package with exposed pad, the part supports composite (CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs at standard-definition and high-definition formats, operating from a single 2.7 V to 3.3 V analog and digital supply. Pricing on distributor inventories such as LCSC starts near $6.45 per unit as of October 2026. A video encoder is a data converter IC that translates digital video streams (parallel ITU-R BT.656 / BT.601, or serial HDMI-derived pixel data) into analog waveforms suitable for legacy displays, broadcast modulation, or recording onto analog media. Within the broader taxonomy it sits inside data converters (video DAC + encoder) and ultimately under interface/signal-chain ICs. The ADV7393 family targets applications that still require analog video outputs after SoC integration. Key specifications include three 2.7 V/3.3 V 10-bit video DACs, support for SD (NTSC/PAL/SECAM) and HD (720p/1080i) timing standards, a low-power sleep pin, I²C control interface, and a wide operating temperature range suitable for consumer set-top boxes, DVD/BD recorders, and video capture cards. The part is specified across -40 °C to +85 °C ambient conditions. Architecturally the device combines a digital encoder block (which inserts sync, blanking, and color modulation) with three current-steering DACs that drive the three analog outputs. Internal PLL-derived timing generation eliminates the need for an external pixel clock in many modes, simplifying board layout. The 40-LFCSP package and exposed thermal pad allow direct PCB thermal dissipation and short analog output traces, important at HD color bandwidths where trace impedance must be tightly controlled. Typical applications include set-top box encoder outputs, DVD and Blu-ray player composite/component video, video capture cards, and industrial test pattern sources. The single 3.3 V rail makes it straightforward to retrofit onto existing 3.3 V designs without adding an LDO. The companion ADV7390/91/92 family members share the same digital architecture and register map, allowing firmware reuse across the encoder line. When designing with this device, keep analog output traces matched to 75 ohm impedance with a 75 ohm termination at the load connector. Place decoupling capacitors immediately adjacent to AVDD and DVDD pins, and tie the exposed thermal pad to a clean analog ground plane. For HD formats, use the 2 x oversampling mode to ease analog filter requirements. This page consolidates distributor pricing, drop-in same-family alternatives (ADV7390/91/92), and practical design notes not found in the manufacturer datasheet alone.
AFE5832LPZAV - 32-Ch Ultrasound AFE, 18.5mW/Ch | Texas Instruments
The Texas Instruments AFE5832LPZAV is a low-power, 32-channel analog front-end (AFE) optimized for portable ultrasound systems, integrating per-channel LNA, attenuator, low-pass filter, ADC, and a passive continuous-wave (CW) mixer in a 15 mm x 15 mm 289-pin NFBGA (ZAV) package. The device supports either 12-bit, 40-MSPS or 10-bit, 50-MSPS output and is pin-compatible with the broader AFE5832 family, enabling drop-in migration between power tiers. An analog front-end (AFE) in ultrasound systems is the analog signal chain that sits between the piezoelectric transducer and the digital beamformer/back-end processor. It typically performs low-noise amplification, time-gain compensation (TGC), anti-alias filtering, and analog-to-digital conversion. As an integrated AFE, the AFE5832LPZAV replaces a discrete multi-chip front end with a single IC, reducing board area, BOM count, and power budget - critical for handheld and cart-based ultrasound where battery life and thermal envelope are primary constraints. Key specifications include 4 nV/rt-Hz input-referred current noise, 18.5 mW per channel power dissipation, 0 dB to 48 dB total gain range via Digital Time Gain Compensation (DTGC), and an LVDS digital interface for high-speed data transfer. The LNA provides programmable gain for near- and far-field reception, and the integrated passive CW mixer supports Doppler modes without an external down-conversion stage. Architecturally, the device uses a per-channel signal chain with shared digital control and bias blocks; the LVDS output bus and the DTGC engine share a common serializer across all 32 channels. Compared with the higher-power AFE5832 (non-LP), the AFE5832LP trades absolute noise margin and maximum sample rate for a substantially lower per-channel power figure, which is essential for portable ultrasound carts operating from limited battery capacity. Typical applications include portable and handheld ultrasound imaging systems, multi-channel CW/PW Doppler receivers, and battery-powered diagnostic equipment. The 32-channel integration is well-matched to mid-density probe arrays (e.g., 32-element linear or curved arrays) used in point-of-care imaging. When designing with this part, ensure the PCB implements a continuous ground plane under the NFBGA with adequate via stitching for thermal dissipation; 289-ball BGA packages require strict reflow profile control and X-ray inspection of solder joints. The LVDS interface length should be 50 ohm differential-impedance matched and kept short to preserve signal integrity at 50 MSPS.
AK4181A - 4-Wire Touch Screen Controller, 12-bit SAR ADC | AKM
The AKM AK4181A is a 4-wire resistive touch screen controller that integrates a 12-bit successive-approximation-register (SAR) analog-to-digital converter with a maximum sampling frequency of 125 kHz. Housed in a compact TSSOP surface-mount package, the AK4181A detects pressed-screen coordinates by performing two successive A/D conversions on the touch-panel analog signals and also measures pen-pressure (Z-axis) touch force. A touch screen controller is a mixed-signal data-acquisition IC that bridges a 4-wire resistive touch panel and an embedded host MCU. The AK4181A sits in the broader signal-chain hierarchy as: touch-screen controller -> resistive-touch digitizer -> data-acquisition IC -> analog front-end -> semiconductor. By handling the analog measurement locally and presenting digital results to the host, the part removes analog switching and biasing complexity from the host firmware, an essential role in any handheld, HMI, or industrial-control system using legacy resistive panels. Key features include pen-pressure measurement (Z-axis), an on-chip thermal sensor for system-temperature monitoring, two auxiliary analog input channels for general-purpose ADC use, direct battery-voltage measurement, an on-chip 2.5 V voltage reference, and a 12-bit SAR ADC with integrated sample-and-hold. The low-power architecture supports battery-powered handheld designs, while the direct-battery-measurement channel allows the host to monitor its own supply without extra external dividers. Typical applications include resistive-touch human-machine interfaces (HMIs), handheld data terminals, industrial control panels, point-of-sale (POS) terminals, consumer electronics with resistive touch, and portable instrumentation. The auxiliary ADC inputs and on-die temperature sensor make the AK4181A useful even in systems that do not require touch input. Design consideration: the 4-wire resistive interface requires proper PCB routing to keep the X/Y drive signals away from noisy digital traces, and the SAR converter's 125 kHz maximum sampling rate limits touch-report rates to roughly a few hundred Hz. Designers should also account for the part's TSSOP thermal envelope and ESD handling at the panel connector. This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes not found in the manufacturer datasheet alone - giving engineers a one-stop reference for evaluating the AK4181A in new designs and as a replacement candidate in legacy 4-wire touch systems.
AK4352VT - 2V Low-Power Multi-Bit DAC | Asahi Kasei
The Asahi Kasei AK4352VT is a 2 V, low-power, multi-bit delta-sigma digital-to-analog converter designed for audio signal generation. The AK4352VT belongs to the ADC/DAC and special-purpose integrated-circuit categories, where it converts digital audio data into an analog voltage output. It is supplied in a tape-and-reel package and is identified by the AK4352VT manufacturer part number. A multi-bit delta-sigma DAC is a semiconductor that uses a multi-bit internal converter and digital noise-shaping techniques to create an analog output from a digital input stream. In a signal chain, a DAC follows the digital source, decoding stage, or digital audio processor. The AK4352VT is therefore positioned between digital audio logic and an analog audio output stage, where its 2 V operating class and low-power design are the principal documented characteristics. The available manufacturer and distributor records identify AK4352VT as a 2 V, low-power multi-bit DAC intended for special-purpose ADC/DAC applications. The part is listed under tape-and-reel packaging, indicating a production configuration intended for automated high-volume PCB assembly. Because the searchable technical record does not expose the complete electrical tables in this result set, detailed resolution, dynamic-range, clock, distortion, and pin-level values should be confirmed in the manufacturer datasheet before schematic sign-off. Typical design roles include digital-to-analog conversion in compact audio equipment, multimedia systems, consumer-electronics signal paths, and equipment requiring a dedicated low-power stereo or single-channel audio output stage. System designers should pay particular attention to supply sequencing, digital-interface compatibility, analog output filtering, and the required bypass capacitors before treating the converter as production-ready. A key design consideration is that a low-power DAC still depends on clean, stable reference and supply rails. Place the required decoupling capacitors close to their associated pins, route analog outputs away from switching nodes, and implement the manufacturer-recommended reconstruction or anti-alias filter. Confirm the exact package drawing and exposed-pin arrangement against the current datasheet before ordering components. This product page consolidates the verified part identity, packaging information, sourcing path, application guidance, and qualification questions for AK4352VT. It is intended to help engineers narrow the design quickly while preserving the need to verify exact electrical limits, pin functions, and layout instructions in the authoritative AK4352VT datasheet.
AK4353VF - 24-Bit 96kHz Stereo DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4353VF is a 24-bit stereo CMOS digital-to-analog converter with a sampling rate of 16 kHz to 96 kHz, a 2.7 V to 5.5 V analog and digital supply range, and a 24-VSOP surface-mount package. It accepts serial digital audio data and produces single-ended analog outputs. An integrated analog filter removes out-of-band noise, so no external reconstruction filter is required. The digital interface supports TTL and CMOS signal levels. An audio DAC is a digital-to-analog converter, a specialized data-conversion IC that transforms digital audio samples into continuous analog voltage signals. Its role in the signal chain is to bridge digital playback systems and downstream analog audio stages. The AK4353VF belongs to the DAC category, within data-conversion ICs and broader semiconductor signal-processing devices. It is suited to compact audio equipment where a serial audio source must feed an analog amplifier, mixer, headphone circuit, or line-level input stage. The principal device features are 24-bit resolution, operation from 16 kHz through 96 kHz, single-ended analog outputs, and integrated analog filtering. The 2.7 V minimum supply voltage permits use with 3.3 V systems, while the 5.5 V maximum supports 5 V analog and digital rails. Serial digital interfacing reduces the number of signal connections compared with a parallel DAC. These characteristics make the device appropriate for consumer audio, digital mixing, multimedia playback, and compact instrument applications. Technically, the AK4353VF combines a CMOS DAC core, digital audio input interface, and analog output stage. Its integrated filtering handles out-of-band components that would otherwise require discrete low-pass reconstruction filters. The digital interface accommodates TTL and CMOS levels, allowing connection to digital audio logic operating across common supply domains. Because the outputs are single-ended, downstream circuitry must provide the required gain and impedance conversion; the AK4353VF does not include a balanced-output stage or an integrated headphone amplifier. Typical applications include CD and DVD player analog output stages, digital mixing consoles, multimedia speaker interfaces, digital audio recording or monitoring equipment, and consumer audio adapters. The 96 kHz maximum sampling rate supports high-resolution digital audio streams, while 24-bit word length preserves fine amplitude detail. Its surface-mount 24-VSOP format supports automated assembly but requires careful handling of the relatively narrow lead pitch. The primary design consideration is decoupling. Place the analog and digital supply capacitors close to their corresponding pins, route digital signals away from the analog outputs, and observe the datasheet grounding guidance. Keep analog and digital return currents separated until their planned connection point, and verify the output amplitude and load requirements of the following amplifier stage before finalizing board-level filtering. This product guidance combines the device specifications, package details, lifecycle information, and engineering considerations needed for initial design evaluation. It also identifies the AK4353VF-E2 temperature-range variant for comparison and explains why a claimed replacement must be checked for package, pinout, interface, and lifecycle compatibility.
AK4358VQ 8-Channel 24-Bit 192kHz DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4358VQ is an eight-channel, 24-bit audio digital-to-analog converter designed for high-resolution PCM and DSD playback. It supports sampling frequencies up to 192 kHz, accepts I2S digital audio data, and is packaged in a 48-LQFP package measuring 7 mm by 7 mm. The converter uses AKM's advanced multibit modulator architecture to balance dynamic range, linearity, and THD+N performance. An audio DAC is a signal-conversion IC that transforms digital PCM or DSD audio samples into continuous analog voltage signals for downstream amplifiers, headphones, line outputs, or powered speakers. Within the broader semiconductor hierarchy, the AK4358VQ is an ADC/DAC converter, an interface IC, and a signal-processing device. Its eight-channel architecture allows one converter to serve multichannel audio systems without requiring eight separate stereo output stages. The AK4358VQ provides 24-bit resolution and operation up to 192 kHz, making it suitable for CD-quality playback, high-resolution audio equipment, multichannel digital mixers, and systems requiring DSD input. Its eight-channel organization reduces system-level routing complexity when a design must support several simultaneous analog outputs. The 48-LQFP package also provides ample perimeter pins for multi-channel analog, digital, clock, and power connections. AKM's advanced multibit modulator architecture is central to the converter's audio performance. A multibit delta-sigma implementation shapes quantization noise outside the audible signal band and supports high linearity when paired with an appropriate analog output stage. The AK4358 is also identified as an eight-channel 112 dB DAC for PCM and DSD applications, making its specifications relevant to demanding digital-to-analog conversion designs. Typical uses include professional audio equipment, multichannel home-theater processors, digital mixing consoles, USB and network audio systems, and multichannel consumer electronics. In each case, the device can receive digital audio through its I2S interface and produce eight balanced or unbalanced analog channels, depending on the external application circuit and output architecture. A careful design should use the manufacturer's pin-description and application-circuit tables when assigning traces, grounding analog and digital return paths, and selecting bypass components. Clock routing, MCLK/LRCK/SCK synchronization, and analog-output filtering are equally important because correct digital timing does not by itself guarantee low-distortion analog performance. This page consolidates the verified AK4358VQ identity, package, resolution, channel count, sampling-rate, interface, and DSD characteristics with practical design guidance. It also distinguishes verified drop-in substitutes from parts that are only functionally similar, helping engineers avoid assuming that an audio converter with similar output counts is pin-compatible.
AK4363VF - 24-Bit Stereo Audio DAC with PLL | AKM
AKM Semiconductor Inc. AK4363VF is a 24-bit stereo CMOS digital-to-analog converter with an integrated phase-locked loop, designed for digital video broadcast set-top boxes and DVD equipment. The device operates from a 2.7 V to 5.5 V supply, supports sampling rates from 16 kHz to 96 kHz, and is packaged in a surface-mount 24-VSOP. A digital-to-analog converter is an interface IC that converts digital audio samples into analog voltage signals suitable for downstream amplifiers, speakers, headphones, or audio-processing stages. The AK4363VF belongs to the broader DAC and mixed-signal IC hierarchy, combining a stereo DAC, clock-recovery circuitry, and analog output filtering in one component. The AK4363VF produces single-ended analog outputs that are internally analog-filtered to suppress out-of-band noise. This filtering approach can eliminate the need for external reconstruction filters in suitable signal chains. Its integrated phase-locked loop can lock to a recovered 27 MHz MPEG clock, with selectable sampling-clock frequencies supporting the converter's 16 kHz to 96 kHz operating range. The serial digital interface, 24-bit conversion resolution, stereo output architecture, and integrated PLL reduce the number of separate components required in a digital-audio reproduction path. Single-ended outputs simplify analog connection compared with a differential-output design, although board-level grounding becomes more important because output-reference noise can couple directly into the reproduced signal. Typical uses include digital broadcast set-top boxes, DVD players, digital video equipment, and other consumer systems that recover a clock from a serial audio stream. The 24-VSOP surface-mount package is suitable for automated production, while its 2.7 V to 5.5 V analog-and-digital supply range permits integration with common embedded multimedia platforms. Designers should route analog and digital return currents carefully, place bypass components near the supply pins, and follow the manufacturer pin-description table when assigning PCB nets. Verify the required master and slave clock arrangement, audio data format, mute behavior, and output load before releasing a PCB because these details determine whether the integrated PLL can operate as intended. This product record combines the converter's defining electrical and packaging characteristics with practical application guidance, sourcing answers, and a compatibility-focused replacement assessment. It is intended to help engineers determine whether the AK4363VF fits an existing 24-VSOP audio design and whether redesign is necessary when the original device is unavailable.
AK4373EN - 24-Bit Stereo DAC with HP/SPK Amp | AKM
The Asahi Kasei Microdevices AK4373EN is a low-power stereo 24-bit digital-to-analog converter with an integrated stereo headphone amplifier and monaural speaker driver in a 32-QFN 5 x 5 mm package. It supports I2S audio input, digital signal processing, and 48 kHz operation, making it suitable for portable audio systems, game consoles, dedicated headphone equipment, navigation products, and portable media players. An audio DAC is a signal-conversion integrated circuit that transforms digital audio samples into analog voltage signals. The AK4373EN combines three functions in one device: a stereo DAC, a stereo headphone amplifier, and a monaural speaker driver. This integration reduces the number of external analog-output blocks in portable equipment and allows the output stages to be configured for different audio use cases. The device provides 24-bit digital audio resolution with support for 48 kHz sampling and an I2S interface. These parameters are suitable for consumer audio playback paths where a compact digital interface and low-power implementation are priorities. The integrated headphone and speaker drivers allow the same converter platform to support headphones, a speaker, or other line-level audio destinations when the application circuit is configured accordingly. AK4373EN also includes digital signal-processing functionality associated with the AK4373 family. The manufacturer describes configurable output-driver use cases, allowing portable equipment designers to select operating arrangements suited to different playback conditions. The digital interface and control registers support integration with a host processor or audio controller, while the integrated analog output stages reduce board area compared with separate DAC and amplifier implementations. Typical uses include game consoles, dedicated headphone drivers, personal navigation devices, portable media players, and other portable-audio or media-player products. In these systems, the AK4373EN can provide a single audio conversion and output solution for a stereo headphone connection or a monaural speaker path. The 32-QFN 5 x 5 mm package is suitable for compact boards, although its exposed-pad construction requires careful PCB land-pattern and thermal design. When designing around the AK4373EN, verify the manufacturer pin description table, supported digital interface modes, analog output configuration, power sequencing, and bypass requirements before laying out the PCB. Keep analog output routing short, place required bypass capacitors close to their associated pins, and follow the package land pattern and exposed-pad soldering recommendations. This page consolidates the device identity, manufacturer documentation, sourcing references, and application guidance for engineers evaluating the AK4373EN.
AK4382AVT - 24-Bit Stereo I2S Audio DAC | AKM
The Asahi Kasei Microdevices AK4382AVT is a 24-bit stereo delta-sigma digital-to-analog converter with an I2S digital audio interface, 112 dB dynamic range, and a 16-pin TSSOP package. It is designed for digital audio equipment that requires a two-channel converter with performance suitable for high-resolution audio systems. A delta-sigma DAC is a data converter that uses oversampling and digital noise shaping to convert digital audio samples into an analog output. It belongs to the broader DAC, data-converter, signal-conversion, and semiconductor hierarchies. In an audio signal chain, the AK4382AVT typically accepts digital samples from a USB interface, audio processor, or digital transport and produces differential analog outputs for a headphone or line-output amplifier stage. The AK4382AVT provides 24-bit resolution, two audio channels, and an I2S interface. The manufacturer datasheet identifies a 112 dB dynamic-range figure and supports operation up to 192 kHz, while one distributor listing also identifies a 216 kHz sampling-rate category. Its advanced multi-bit delta-sigma architecture is intended to balance dynamic range, linearity, and implementation cost in digital audio equipment. The device operates from a 5 V supply and is specified for an ambient operating range of -40 °C to +85 °C. The AK4382AVT is packaged in a 16-pin TSSOP for surface-mount assembly. Its reel designation identifies the supplied component as a production packing option, allowing use in automated PCB assembly and volume manufacturing. Typical applications include high-resolution audio DAC boards, USB and network audio players, digital mixing consoles, audio receivers, professional audio interfaces, and premium consumer playback equipment. It is also suitable for evaluation platforms where a stereo I2S-to-analog conversion stage is required before adding a high-current output amplifier. The primary layout consideration is digital-clock and analog-output isolation. Route the I2S data, bit clock, and master clock away from the analog output network, use a continuous ground reference, and follow the manufacturer pin-description and typical-application circuits when assigning decoupling and output-filter components. Correct supply bypassing and controlled clocking are essential for preserving the specified signal-to-noise performance. This page organizes the technical specifications, sourcing guidance, compatible ordering codes, comparison information, and practical design considerations into a consolidated engineering reference for evaluating the AK4382AVT in precision stereo audio designs.
AK4384ET - 24-Bit 192kHz Stereo DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4384ET is a 24-bit, two-channel audio DAC with a 106 dB dynamic range and operation up to 192 kHz, packaged in a 16-pin TSSOP with 0.65 mm pitch. It accepts I2S digital audio and is intended for compact, cost-sensitive audio systems that require a high-performance stereo conversion stage. An audio DAC is a signal-conversion integrated circuit in the ADC/DAC category. Its function is to transform digital audio samples into an analog voltage suitable for a downstream headphone amplifier, line amplifier, mixer, or speaker system. Within the broader semiconductor hierarchy, an AK4384ET DAC belongs to the ADC/DAC class of data-conversion ICs, where resolution, dynamic range, linearity, clocking, and output filtering determine how faithfully digital audio is reproduced. The AK4384ET provides a 24-bit conversion resolution, 106 dB dynamic range, and support for sampling rates through 192 kHz. Its two-channel architecture allows simultaneous stereo playback while reducing the number of external conversion devices required. The manufacturer describes the device as a cost-and-performance solution for audio systems and uses a multibit modulator architecture to preserve linearity and improve THD+N performance. The AK4384ET uses AKM's multibit DAC architecture rather than being characterized as a basic one-bit converter. This architecture is designed to balance wide dynamic range with improved linearity. Digital audio enters through I2S-compatible logic, while the analog output stage requires appropriate filtering and signal-chain design to achieve the intended channel separation, distortion, and noise performance in the finished equipment. Typical applications include compact digital audio players, consumer audio equipment, digital mixing consoles, computer-audio accessories, and other stereo playback products. The 16-pin TSSOP package supports conventional surface-mount assembly, while the 192 kHz capability accommodates applications that require high-resolution PCM source material. Integration into a complete product also requires correct clocking, grounding, output filtering, and analog-output implementation. During PCB design, place the device close to its digital-audio source and analog output circuitry to minimize sensitive-signal routing lengths. Follow the manufacturer pin-description table for power, ground, clock, data, and analog-output connections. Decoupling and analog-filter component values should be taken directly from the manufacturer reference circuit rather than inferred from generic audio-DAC layouts. This page consolidates the exact AK4384ET identity, package information, resolution, channel count, sampling-rate capability, and documented conversion characteristics into an engineering-focused selection guide. It also separates confirmed attributes from parameters that require confirmation from the manufacturer datasheet, helping designers assess fit before beginning a layout, prototype, or production qualification.
AK4385ET - 24-Bit 192kHz Stereo DAC | AKM
The Asahi Kasei Microdevices/AKM AK4385ET is a 24-bit, 192 kHz, two-channel delta-sigma digital-to-analog converter with a 108 dB dynamic range and an I2S interface, housed in a 16-pin TSSOP package with 0.65 mm pitch. It supports a 5 V supply and operating temperatures from -20°C to +85°C. A digital-to-analog converter, or DAC, converts digital audio samples into an analog voltage suitable for audio amplification, headphones, speakers, line-level inputs, or digital recording equipment. Within the broader semiconductor hierarchy, the AK4385ET is an audio data-converter IC and a specialized member of the ADC/DAC family. Its two-channel architecture supports stereo audio conversion without requiring two separate external DAC packages. The principal performance characteristics are 24-bit resolution, a maximum sampling rate of 192 kHz, 108 dB dynamic range, and full differential SCF outputs. The 24-bit interface accommodates high-resolution digital audio data, while the 192 kHz capability supports high-rate studio, mastering, broadcast, and consumer applications. Full differential outputs can also remove the need for AC-coupling capacitors in suitable output networks. AKM describes the AK4385 as using a multibit modulator architecture to preserve linearity and improve THD+N performance. The I2S interface makes the device suitable for systems that transmit PCM audio data from a digital audio processor, receiver, decoder, or source. The compact 16-pin TSSOP outline supports surface-mount assembly while providing separate connections for the two-channel interface, supplies, clock signals, and analog outputs. Typical uses include professional digital mixers, multichannel audio processors, high-resolution music players, home-theater equipment, recording interfaces, and digital audio monitoring. In stereo systems, the converter can provide left and right analog outputs from a common digital source. In multichannel equipment, several devices may be used when more than two channels are required, subject to the interface and clock design described in the manufacturer datasheet. Designers should follow the pin-description table, recommended application circuit, and interface timing diagrams in the AK4385 datasheet before assigning PCB signals. Keep the digital clock and data traces away from the analog outputs, use the specified decoupling arrangement, and observe the required relationship between the audio master clock and the I2S source clock. The differential outputs should use the manufacturer-recommended load and reconstruction network rather than an improvised output stage. This product page combines the exact AK4385ET specifications, package information, interface characteristics, application guidance, and design cautions needed to evaluate the converter before schematic capture. It also highlights where the datasheet must be consulted for the complete pin map, timing limits, recommended circuit, and electrical-characteristic test conditions.
AK4386ET - 24-Bit 96kHz Stereo Audio DAC | AKM
AKM Semiconductor AK4386ET is a 24-bit, two-channel, low-voltage, low-power stereo delta-sigma digital-to-analog converter with a 96 kHz sampling rate and an I2S interface, housed in a 16-pin TSSOP package. It achieves 100 dB dynamic range during 3 V operation. A stereo DAC converts digital audio samples into left- and right-channel analog signals for subsequent amplification and speaker or headphone drive. The AK4386 belongs to the delta-sigma DAC hierarchy, where a multi-bit internal architecture and digital reconstruction filters shape the output waveform. This component therefore fits between an audio source and an analog output stage in portable, home-audio, set-top-box, and similar digital audio systems. The AK4386 uses AKM's Advanced Multi-Bit Delta-Sigma architecture. According to the AK4386 manufacturer datasheet, this architecture provides a dynamic range of 100 dB at a 3 V supply. The device combines SCF and CTF filters to improve performance in systems experiencing excessive clock jitter. Its 24-bit resolution supports high-resolution digital audio, while the two-channel organization covers standard stereo playback in one compact device. The AK4386 operates from a single supply in the 2.2 V to 3.6 V range, making it appropriate for low-voltage portable equipment. Its electrical interface includes I2S, a common serial format for transferring audio data between digital signal processors, audio processors, and converters. The datasheet identifies the AK4386 as a low-voltage, low-power component designed for portable audio systems including MP3 equipment, as well as home-audio systems such as set-top boxes. Typical uses include portable music players, home-audio equipment, digital set-top boxes, game-console audio paths, and other embedded stereo audio products. The 16-pin TSSOP package supports conventional surface-mount assembly, while a 0.650 mm pin pitch provides a compact footprint for space-constrained boards. The reel packaging format is intended for automated component placement and high-volume production. When designing a circuit around the AK4386, treat clock quality, supply stability, and analog-output grounding as integral parts of the audio path. Keep the converter and its decoupling close to the audio source, follow the manufacturer pin-description table for every connection, and reserve quiet analog routing for the left- and right-channel outputs. Digital and analog return currents should not share a noisy path. This page consolidates the AK4386ET electrical characteristics, package information, application guidance, pin-data status, and drop-in-replacement analysis. It also identifies where engineering decisions depend on the manufacturer datasheet, including clocking, filter configuration, analog output implementation, and PCB layout.
AK4388AET - 24-Bit 192kHz Stereo Audio DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4388AET is a 24-bit, 192 kHz, two-channel audio digital-to-analog converter with I2S digital audio input in a lead-free 16-pin TSSOP package. The device is designed for compact audio systems requiring high-resolution conversion, including professional audio equipment, consumer audio products, digital mixers, and multi-channel audio platforms. An audio DAC is a semiconductor that converts digital PCM or I2S audio samples into continuous analog voltage signals suitable for audio amplifiers and loudspeakers. It belongs to the digital-to-analog converter class within the broader ADC/DAC and signal-conversion IC hierarchy. Its role is to translate the numerical representation of an audio waveform into a balanced or unbalanced analog output while preserving amplitude and linearity as accurately as practical. The AK4388A provides 24-bit resolution, a maximum sampling rate of 192 kHz, two-channel conversion, and I2S interface support. These characteristics suit high-resolution playback and multirate audio architectures. The 16-pin TSSOP body measures approximately 6.40 mm by 5.00 mm and uses a 0.65 mm lead pitch, allowing compact implementation on densely populated audio boards. AKM's multibit modulator architecture is intended to combine wide dynamic range with strong linearity. The manufacturer describes the AK4388A as a cost-and-performance-oriented solution for audio systems. Its two-channel architecture permits simultaneous left- and right-channel playback from one device, reducing board area compared with separate single-channel converters where that arrangement is practical. Typical uses include digital mixing consoles, professional audio interfaces, CD and network-audio playback equipment, active speakers, automotive infotainment systems, and consumer home-theater products. The I2S interface also makes the converter suitable for systems whose audio processor, USB interface, or network audio decoder already produces standard serial audio data. PCB design should account for the distinction between the digital audio interface and analog output path. Keep digital clock and data traces away from the analog outputs, place the required bypass capacitors close to their supply pins, and follow the manufacturer datasheet for output-filter and reference-component recommendations. Correct grounding is especially important because converter performance depends on low-noise analog supply and reference conditions. This product page combines the verified package and interface details with application-specific guidance for digital audio conversion. It also provides practical design notes, technical comparisons, and sourcing questions that help engineers evaluate the AK4388AET before integrating it into a high-resolution audio design.
AK4388VT - 24-Bit 192kHz Stereo DAC | Asahi Kasei
Asahi Kasei Microdevices AK4388VT is a 24-bit, 192kHz, two-channel digital-to-analog converter for high-performance audio systems. It uses AKM's multibit modulator architecture to provide a wide dynamic range and strong linearity while targeting cost-sensitive consumer and professional audio equipment. The device is supplied in tape-and-reel packaging for automated surface-mount assembly. A DAC is a digital-to-analog converter, a category of audio signal-conversion IC that transforms digital audio samples into an analog voltage suitable for headphone, line-level, or power-amplifier inputs. Within the broader product hierarchy, the AK4388VT belongs to the ADC/DAC class of integrated circuits and supports digital-audio signal chains that require simultaneous conversion of two channels. The AK4388's headline capabilities are 24-bit resolution, a maximum sampling frequency of 192kHz, and two-channel output. These specifications make the converter suitable for hi-fi playback, home-theater equipment, digital mixing, USB audio interfaces, and powered speakers. The dual-channel architecture allows left and right program channels to be converted through one integrated device while retaining a compact surface-mount footprint. AKM's multibit modulator architecture is intended to balance dynamic range, linearity, and implementation cost. Unlike a simple binary-weighted converter, a multibit approach can reduce quantization-related distortion and support improved THD+N performance. The AK4388 is therefore positioned between basic consumer converters and more specialized audio DACs used in high-end measurement equipment. Typical applications include consumer hi-fi playback, compact home-theater systems, active speakers, digital audio mixers, and multi-channel audio products with stereo output stages. In these systems, the converter accepts interleaved digital audio data and produces left and right analog outputs. The host processor or audio interface must supply a compatible digital interface, while the analog section must provide appropriate filtering, grounding, and output amplification. The primary design consideration is matching the digital interface, clocking, and analog implementation to the manufacturer's application guidance. Keep power and ground connections short, place decoupling capacitors close to the device, and use a clean low-noise supply because converter performance can be affected by clock jitter, reference quality, PCB return paths, and analog-output loading. This product page organizes the verified AK4388VT characteristics, sourcing information, design guidance, application context, and compatibility limitations into one engineering reference. It also distinguishes confirmed device identity from parameters that require consultation of the manufacturer datasheet before schematic release or production qualification.
AK4393VF - 24-Bit Stereo Audio DAC | Asahi Kasei Microdevices
The Asahi Kasei Microdevices AK4393VF is a 24-bit stereo delta-sigma digital-to-analog converter with a 3 V to 5.25 V analog and digital supply range, I2S audio input, and a 28-pin VSOP package. The manufacturer positions the device for high-performance digital audio, including DAT and DVD applications using its advanced multi-bit delta-sigma architecture. An audio DAC is a converter that transforms digital PCM samples into analog voltage signals suitable for audio amplification and speaker systems. The AK4393VF belongs to the digital-to-analog converter hierarchy, where it combines a digital interface, digital filtering, a multi-bit delta-sigma modulator, and analog output stages. Its stereo architecture supports two audio channels while maintaining a 24-bit digital data path for high-resolution audio systems. The principal features include 24-bit resolution, a stereo delta-sigma conversion structure, I2S digital audio input, and operation from a 3 V to 5.25 V supply. Manufacturer material describes the device as a high-performance DAC for 96 kHz sampling applications, while distributor product information identifies a maximum sampling rate of 108 kHz for the exact AK4393VF orderable variant. These figures should be used according to the operating mode and interface configuration specified in the manufacturer datasheet. The advanced multi-bit delta-sigma architecture is central to the converter design. Instead of relying on a conventional single-bit approach, the multi-bit system is intended to provide wider dynamic range while retaining low distortion. The integrated 24-bit digital filter performs decimation and band-limiting of the incoming PCM stream, helping reduce aliasing and out-of-band noise before the signal reaches the analog output stage. Typical applications include CD and DVD audio players, DAT equipment, digital mixing consoles, home-theater audio processors, and other multichannel or stereo systems requiring a dedicated 24-bit DAC. The I2S interface simplifies connection to digital audio transceivers, receivers, and processors, while the dual analog outputs support conventional left-right signal routing. External analog filtering and output-stage design remain important because the complete audio path determines the final channel separation, noise floor, and distortion performance. When laying out the board, place the digital interface, analog output, ground-return, and decoupling connections according to the pin-description table and application circuit in the manufacturer datasheet. Analog and digital ground domains should be connected at the recommended analog reference point. Decoupling capacitors should be positioned close to their supply pins, and the analog output traces should remain short and physically separated from clock and data lines to reduce coupling into the reconstructed audio signal. This page combines manufacturer-device positioning, exact AK4393VF catalog attributes, package information, application guidance, and comparison-oriented selection criteria. It also distinguishes the verified ordering information from parameters that require confirmation in the manufacturer datasheet, helping engineers move quickly from component identification to board-level validation.
AK4393VM - 24-Bit 108kHz Stereo DAC | Asahi Kasei
Asahi Kasei AK4393VM is a 24-bit stereo audio digital-to-analog converter with a maximum sampling rate of 108 kHz, an I2S digital interface, and a 28-pin SSOP package. The device uses an advanced multi-bit delta-sigma modulator architecture to provide a wider dynamic range while retaining the low-distortion characteristics associated with high-performance audio converters. It also incorporates a 24-bit digital filter and is designed for DAT, DVD, and other professional and consumer audio systems. An audio DAC is a signal-conversion integrated circuit that reconstructs continuous analog voltages from digital audio samples. Within the signal-chain hierarchy, the AK4393VM belongs to the ADC/DAC class of data-converter ICs and supports digital audio systems, home theater, digital recording equipment, and high-fidelity playback. Its 2-channel architecture converts left and right digital streams into balanced or unbalanced analog outputs through the application circuit. Key features include 24-bit resolution, operation up to 108 kHz, stereo output, an I2S interface, an integrated 24-bit digital filter, and the advanced multi-bit delta-sigma architecture. The multi-bit approach is significant because it spreads quantization error across multiple internal bits, supporting improved dynamic-range performance without abandoning the fundamental advantages of delta-sigma conversion. The 28-SSOP package supports conventional surface-mount PCB assembly. The AK4393VM is intended for digital audio paths requiring separate left and right conversion channels and a standard serial digital interface. Its architecture is particularly relevant to source equipment operating at ordinary CD, DVD, DAT, and related high-resolution audio rates. Because the converter includes a digital filter, system designers should review the manufacturer’s timing and filter recommendations when configuring clocking, filtering, and digital signal routing. Typical applications include professional DAT equipment, DVD-audio and home-theater systems, digital mixing consoles, multichannel audio processors, sampling workstations, and high-fidelity consumer playback equipment. For designs with digital-domain processing, the AK4393VM can serve as the final stereo conversion stage after decoding, mixing, or sample-rate-conversion functions. The most important design consideration is preserving the converter’s recommended analog and digital layout. Keep the I2S clock and data routing short, use clean grounding between digital and analog sections, and follow the manufacturer’s output-filter and reference-component recommendations. Analog output impedance, load capacitance, and clock jitter can affect measured channel performance even when the digital data is valid. This product page consolidates the AK4393VM architecture, interface information, package details, application guidance, and compatible replacement information into an engineering-focused reference for audio-product designers, procurement teams, and PCB layout engineers.
AK4395VF 24-Bit 192kHz Stereo DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4395VF is a high-performance stereo audio digital-to-analog converter with 24-bit resolution, operation up to a 192 kHz sampling rate, and a 28-VSOP package. Its architecture includes a 24-bit digital filter and a multibit delta-sigma modulator, while the analog and digital sections operate from a 5 V supply. The manufacturer identifies the device as a premium DAC for DVD-Audio and other high-resolution audio systems. An audio DAC is the final digital-to-analog conversion stage in a playback chain. It converts I2S-formatted digital samples into left and right analog voltages suitable for headphone or line-output amplifiers. Within the component hierarchy, the AK4395VF is an audio DAC, which belongs to the broader ADC/DAC and signal-conversion IC category used in digital audio equipment. The principal features include 24-bit data resolution, a maximum sampling frequency of 192 kHz, stereo operation, I2S digital audio input, a 5 V supply, and digital-filter stopband attenuation of at least 110 dB. The high stopband attenuation is significant because it suppresses out-of-band noise and aliasing energy that could otherwise appear near the audio baseband after digital-to-analog conversion. Internally, the AK4395VF combines a 24-bit digital filter with a multibit delta-sigma conversion architecture. The digital filter provides sharp transition characteristics for high-resolution PCM streams, while the stereo converter produces separate left- and right-channel analog outputs. This combination targets applications requiring faithful reproduction of 44.1 kHz, 48 kHz, 96 kHz, 176.4 kHz, and 192 kHz source material, subject to the interface and system clock implementation. Typical applications include high-resolution DVD-Audio players, premium CD and network-audio players, digital audio decoding boards, professional audio interfaces, and two-channel headphone or line-output stages. The 192 kHz capability is particularly relevant to studio masters and archival playback systems, while the 110 dB or greater filter attenuation helps reduce wideband aliasing noise. The 28-VSOP package requires a stable, low-noise 5 V supply and careful analog-output routing. Keep digital and analog return paths separated, use short traces around the converter, and follow the manufacturer pin-description and application-circuit tables when assigning power, ground, clock, and I2S signals. The exact pinout, output topology, and external component requirements should be taken directly from the AK4395VF datasheet. This page organizes the AK4395VF product information into a technical summary, application guidance, specification comparisons, and practical design notes. It is intended to help engineers identify the correct resolution, sampling-rate, interface, package, and supply requirements before integrating the converter into a high-resolution audio design.
AK4396VF - 24-Bit Stereo 192kHz DAC | AKM | VSOP-28
Asahi Kasei Microdevices AK4396VF is a high-performance, two-channel advanced multi-bit delta-sigma digital-to-analog converter designed for 192 kHz DVD-Audio operation. The device supports 24-bit digital audio and is supplied in a 28-pin VSOP package with a 0.65 mm pitch. Its architecture combines an advanced multi-bit delta-sigma system with a 24-bit digital filter, positioning it for high-fidelity stereo audio equipment. A digital-to-analog converter is an interface IC that converts digital audio samples into proportional analog voltages or currents. Within the signal-chain hierarchy, a DAC sits between a digital audio source and an analog output stage. The AK4396VF is a stereo DAC, meaning that one package provides two audio conversion channels for applications such as CD players, DVD-Audio systems, network-audio receivers, and premium consumer audio equipment. The headline capabilities of the AK4396VF are 24-bit resolution, operation up to a 192 kHz sampling rate, and two-channel audio conversion. The 24-bit format provides substantially more code values than conventional CD audio, while the 192 kHz capability supports high-resolution digital audio sources. The advanced multi-bit delta-sigma implementation is intended to improve conversion performance while retaining the integration advantages of a compact mixed-signal IC. The AK4396 is designed around separate analog and digital supply concepts, including dedicated reference and power-related connections. Its digital filter forms part of the signal path and requires the correct clocking and digital-audio interface configuration. The manufacturer documentation identifies the AK4396VF as a 28-pin VSOP device intended for surface-mount assembly, with an indicated operating temperature range of -40°C to +85°C. Typical uses include high-resolution CD and DVD-Audio players, digital audio amplifiers, home-theater equipment, professional monitoring electronics, and multi-channel audio systems using multiple DAC channels or devices. In each case, the device requires a clean analog supply, appropriate reference voltage, compliant input clocks, and an output-stage design matched to the DAC’s analog outputs. Designers should preserve the analog and digital grounding strategy specified by the manufacturer, place decoupling capacitors close to their associated supply pins, and treat the reference and analog-output nodes as sensitive paths. Clock source and filter configuration also determine whether the device operates in its intended audio mode. Consult the manufacturer’s pin-description and application sections before assigning tracks on a new board. This product record combines the AK4396VF device description, family comparison information, package identification, and practical design guidance in one engineering-focused reference. It also distinguishes confirmed drop-in options from related converters that require additional compatibility verification.
AK4397EQ - 32-Bit 192kHz High-Performance DAC | AKM
Asahi Kasei Microdevices AK4397EQ is a high-performance premium 32-bit digital-to-analog converter designed for 192 kHz sampling, including the DVD-Audio operating mode and an integrated 32-bit digital filter. The converter is supplied in tape-and-reel packaging for high-volume audio equipment production. A digital-to-analog converter, or DAC, converts digital audio samples into an analog voltage that drives an audio output stage. The DAC belongs to the broader signal-conversion hierarchy: converter IC, audio data converter, DAC, and ultimately semiconductor. AKM's multibit modulator architecture supports high dynamic range while preserving linearity, improving total harmonic distortion plus noise performance in demanding playback systems. The AK4397EQ accepts 32-bit digital audio data and supports sampling rates up to 192 kHz. Its integrated digital filtering provides a defined conversion path before the analog output stage. Full differential switched-capacitor-filter outputs remove the need for AC-coupling capacitors between the converter and a subsequent balanced audio amplifier, simplifying high-end audio board design and reducing low-frequency phase effects. The multibit modulator is a key technical feature. Its architecture is designed to balance dynamic range, linearity, and THD+N performance rather than relying only on resolution alone. Differential SCF outputs support low-noise balanced downstream amplification and reduce sensitivity to ground and supply disturbances when the analog section is laid out carefully. Typical applications include premium CD and DVD-Audio players, network audio players, digital audio workstations, home-theater receivers, and high-resolution headphone amplifiers. The device is also suitable for professional monitoring equipment where the combination of 192 kHz operation, digital filtering, and differential analog outputs supports faithful signal reproduction. The analog and digital sections must be routed as separate return paths on the PCB, with the analog ground and digital ground joined according to the manufacturer's reference layout. Differential output routing should be symmetric, and supply bypass capacitors should sit close to their corresponding pins. Confirm the complete pin mapping and external component values in the AKM AK4397 datasheet before layout release. This page organizes the AK4397EQ's documented conversion capabilities, application guidance, interface considerations, and engineering trade-offs in a form that supports component selection, schematic review, and PCB planning.
AK4399EQ - 32-Bit 216kHz DSD Audio DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4399EQ is a high-performance 32-bit audio digital-to-analog converter rated for sampling rates up to 216 kHz, with DSD support, I2S/serial digital audio input and a 44-pin LQFP (10 x 10 mm) surface-mount package. It is specified at 123 dB dynamic range for low-distortion, wide-range playback and targets DVD-Audio-class and high-resolution networked audio sources. A DAC, or digital-to-analog converter, is the data converter that turns digital audio sample streams into a continuous analog voltage that can drive amplifiers, headphones or line inputs. Within the semiconductor hierarchy, a DAC sits under audio data converter, then data converter IC, then integrated circuit. The AK4399 belongs to the family of premium stand-alone stereo DACs rather than integrated audio codecs, which lets a designer keep the digital source and the analog output stage architecturally separate. Key features include a 32-bit internal digital filter designed for low distortion and wide dynamic range, 216 kHz maximum sample-rate operation, DSD decoding capability, serial (I2S-compatible) digital audio input, and a compact 44-LQFP surface-mount package with 0.80 mm lead pitch. The device is supplied lead-free and is a surface-mount part suited to automated assembly. Architecturally, the AK4399 separates the digital decoding stage from the analog output stage so that switching noise in the digital domain is rejected before reaching the output pins. The internal 32-bit digital filter is the element that shapes the audio band and limits aliasing, while the analog section determines the final distortion and dynamic-range floor. Because it is a discrete converter rather than a codec, it accepts digital audio from any upstream source - a network streamer, a USB interface, a Blu-ray or CD transport, or a digital mixer - without imposing that source's DAC. Typical applications include high-end network streamers, USB audio interfaces, digital preamplifiers, CD and SACD transports, USB DAC boards, hi-fi headphone output stages and professional monitoring consoles. The 123 dB dynamic-range figure suits designs where the DAC is expected to be the limiting element in the signal chain. When designing around the AK4399EQ, keep analog and digital return currents separated, provide clean regulated supplies with local decoupling close to the supply pins, and treat the analog output as a high-impedance load. Confirm the clocking scheme and master/slave relationship with the upstream digital source, since interlock and word-clock errors are the most common cause of audible noise and clicks. This page consolidates manufacturer description data, distributor availability records, a pin-compatible comparison table and practical design notes so that engineers can evaluate the AK4399EQ against premium 32-bit DAC alternatives without reconstructing the same information from multiple sources.
AK4413EQ - 120dB 24-Bit 4ch Audio DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4413EQ is a high-performance four-channel audio digital-to-analog converter (DAC) delivering 120 dB dynamic range with 24-bit resolution and operation up to 216 kHz, housed in a 44-pin LQFP surface-mount package. It accepts I2S-format digital audio data and provides four independent analog output channels suitable for multi-channel consumer and professional audio equipment. An audio DAC is the final conversion stage in a digital audio signal chain, transforming I2S or other digital audio words into analog voltage signals that drive amplifiers, headphones, or line-level inputs. The DAC sits in the broader hierarchy of data-converter integrated circuits, alongside ADCs, and ultimately within the semiconductor and signal-processing domains that define modern audio playback, recording, and broadcast hardware. Key features of the AK4413EQ include its 120 dB dynamic range figure, which sets the noise floor and usable signal-to-noise ratio for the analog outputs, and 24-bit word-length handling that preserves the full depth of high-resolution source material. Four-channel output allows a single device to serve surround playback, multi-zone listening, headphone plus line-out systems, or digital mixing consoles without requiring four separate converter packages. Architecturally, the AK4413EQ combines a high-performance switched-capacitor output stage with a low-noise internal reference and digital interpolation/filtering for decimation of the incoming high-rate stream. Because it supports sampling rates up to 216 kHz, the converter handles oversampled source material used in high-resolution and mastering workflows where standard 44.1 kHz or 48 kHz rates would not suffice. Typical applications include AV receivers, USB and network audio players, digital mixing consoles, professional monitors, automotive head units, and headphone DAC/DSP platforms. For each of these, the four-channel architecture and high dynamic range reduce the number of discrete converter boards needed. One key design consideration is that the AK4413EQ requires careful analog and digital layout separation, with short, low-impedance routing from the digital interface to the DAC and a clean, star-grounded analog output section. Filter and output capacitors should be placed directly at the relevant pins to minimize added noise and distortion. This page organizes the AK4413EQ specifications, drop-in conversion alternatives, package details, and practical design guidance into a single engineering reference that supports part selection, schematic review, and sourcing decisions.
AK4414EQ - 32-Bit 4-Channel 120dB Audio DAC | AKM
The Asahi Kasei Microdevices AK4414EQ is a high-performance 32-bit, four-channel digital-to-analog converter with a stated dynamic range of 120 dB and support for audio data rates up to 216 kHz. The device uses I2S digital audio interfacing and is packaged in a 44-pin LQFP measuring 10 mm by 10 mm. These headline characteristics position it for premium multichannel audio systems where resolution, channel density, and compact integration are important. An audio DAC is an integrated circuit that converts digital audio samples into analog voltage signals for subsequent amplification, filtering, and output to speakers or headphones. Within the signal chain, it belongs to the broader data-converter hierarchy and operates between a digital audio source and an analog output stage. The AK4414EQ combines four DAC channels with a 32-bit conversion format in one surface-mount package. The confirmed headline specifications are 32-bit resolution, four DAC channels, 120 dB dynamic range, operation up to 216 kHz, and I2S interface support. Its dual supply information lists a 2.7 V to 3.6 V range for the lower-voltage supply and a 5 V supply. These values are important when matching the converter to the clocking, logic, and analog-output architecture of the host equipment. The four-channel architecture is particularly useful for multichannel consumer and professional audio equipment. A single AK4414EQ can implement four DAC channels, while the 32-bit format accommodates high-resolution source material and the 216 kHz capability supports high-rate audio streams. The 120 dB dynamic-range figure describes a noise-sensitive conversion function suited to premium playback, monitoring, and networked-audio equipment. Typical design opportunities include multichannel audio decoders, high-fidelity playback systems, digital mixing consoles, audio interfaces, and home-theater equipment. In these systems, the AK4414EQ can receive I2S-formatted digital audio and provide analog outputs for downstream amplification. The exact output architecture, filter settings, clock requirements, and bypass behavior should be established from the manufacturer datasheet before schematic capture. PCB implementation requires careful treatment of power, ground, digital clocking, and analog output routing. Keep the DAC power rails and analog outputs away from noisy switching nodes, use low-impedance grounding, and assign the package pins according to the manufacturer pin-description table. Because the verified information does not expose the complete pin list, the pin assignment and exposed-pad connection should be checked directly in the manufacturer datasheet. This page combines the confirmed AK4414EQ specifications, package information, sourcing guidance, and practical selection context. It also separates confirmed characteristics from parameters that require datasheet review, helping engineers establish a technically sound design without introducing unsupported electrical assumptions.
AK4420ET - 24-Bit 192kHz Stereo DAC | AKM | Audio
Asahi Kasei Microdevices/AKM AK4420ET is a 24-bit stereo delta-sigma digital-to-analog converter with support for audio sampling rates up to 192 kHz, an integrated 2 Vrms output buffer, and a 16-pin TSSOP package. The converter operates from a 5 V supply and accepts I2S-format digital audio data. An audio DAC is a data converter that transforms digital PCM samples into an analog voltage suitable for amplification or line-level output. In the electronic-component hierarchy, the AK4420ET belongs to the DAC family, falls within data converters and audio ICs, and ultimately serves as a semiconductor interface between digital audio systems and analog audio signal chains. The AK4420ET's headline features include 24-bit resolution, operation up to 192 kHz, two audio output channels, and a 2 Vrms output stage. Its integrated output buffer uses a charge pump to develop an internal negative supply rail, supporting a ground-referenced 2 Vrms output. This architecture reduces the external component count compared with a converter that requires discrete output buffering. AKM's multibit modulator architecture is the basis of the conversion engine. The digital input and analog output sections are combined in a compact package intended for high-resolution audio equipment. The available operating details establish the core signal format, supply requirement, channel count, output level, and package dimensions, while other electrical limits should be confirmed against the manufacturer datasheet before final circuit sign-off. Typical uses include CD and DVD player digital-to-analog stages, active speaker crossover networks, professional audio equipment, home theater receivers, and other consumer audio products. The 192 kHz capability is useful for high-resolution source material, while the integrated stereo buffer simplifies analog output implementation when the required signal level is close to 2 Vrms. The main design consideration is analog integration. Keep the digital interface traces compact, provide a stable low-noise 5 V supply, and follow the datasheet's grounding and decoupling layout. The output stage and charge pump can influence power-supply and analog-output behavior, so component placement should preserve short return paths and minimize coupling from switching circuitry into the audio output.
AK4420VT 24-Bit 192kHz Stereo DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4420VT is a stereo audio digital-to-analog converter supporting 24-bit digital audio at sampling rates up to 192 kHz and providing a 2 Vrms output. The device accepts I2S-format digital audio and is packaged in a 16-pin TSSOP. Its combination of high-resolution data handling, stereo output capability, and a compact surface-mount package makes it suitable for digital audio equipment, USB audio interfaces, consumer electronics, and compact playback systems. An audio DAC is the bridge between a digital audio source and an analog output stage. In the signal chain, digital audio data enters the converter, is reconstructed into analog voltage signals, and is then amplified or filtered for loudspeakers, headphones, line inputs, or recording equipment. The AK4420VT operates within the ADC/DAC portion of the broader semiconductor hierarchy, where its primary function is converting 24-bit I2S samples into a stereo analog signal suitable for downstream audio circuitry. The headline capabilities of the AK4420VT are a 24-bit DAC resolution, operation up to 192 kHz, stereo output, I2S digital audio input, and a 2 Vrms output level. These parameters distinguish it from lower-resolution or lower-bandwidth converters intended for general-purpose or low-cost audio paths. The 192 kHz capability also allows the converter to handle high-rate material associated with studio-quality source material, archival playback, and high-resolution audio equipment when the rest of the signal chain supports those rates. The AK4420VT is specifically identified as an audio DAC rather than a general-purpose codec. It therefore addresses the conversion stage between a digital audio interface and analog circuitry, without implying that it includes analog-to-digital conversion, microphone preamplification, headphone amplification, or a complete USB interface. System partitioning should preserve those functional boundaries: the AK4420VT can receive digital samples from a USB controller, audio processor, or digital interface, while separate analog stages determine the final output level and load capability. Typical applications include high-resolution USB audio interfaces, digital audio player boards, compact consumer audio products, line-level stereo conversion, and embedded playback systems. The 16-TSSOP package supports dense surface-mount construction, although analog layout remains critical because the DAC output and digital clock and data connections can affect signal integrity. The manufacturer datasheet should be used to assign every pin and to select the external clock, digital-interface, power, and output-network requirements for the final design. When designing around the AK4420VT, begin with the complete system signal path rather than the converter in isolation. Confirm that the upstream source supports the intended bit depth and sample rate, that the digital interface format and clocking agree with the device configuration, and that the downstream amplifier can accept the resulting analog output. The principal trade-off is that a compact TSSOP device does not itself provide headphone or speaker drive capability, so a separate output amplifier may be required. This product data combines the exact manufacturer-related descriptions, interface resolution, maximum sampling rate, output amplitude, and package information with practical selection and integration guidance. It is intended to help engineers identify the correct converter, understand its functional boundaries, and plan a low-noise audio implementation before consulting the full manufacturer datasheet for application-specific details.