بەرهەمەکان (970+)

CD4541BF - CMOS Programmable Timer, 20 V | Texas Instruments
CD4541BF

CD4541BF - CMOS Programmable Timer, 20 V | Texas Instruments

The Texas Instruments CD4541BF is a CMOS programmable timer rated to 20 V, with a 16-stage binary counter, an external RC-controlled oscillator, automatic power-on reset, and programmable output-stage selection in a 14-pin CDIP package. It operates across the automotive temperature range of -55°C to +125°C and is intended for timing, counting, pulse generation, and delayed-output applications. A programmable timer is a clock-and-timing semiconductor that combines oscillator, counter, reset, and output-control functions. The CD4541B belongs to the CMOS timer and counter hierarchy, where an external resistor-capacitor network establishes the oscillator timing and the internal binary counter divides that frequency into selectable output periods. Its high-voltage 20 V rating provides additional supply-voltage headroom compared with lower-voltage CMOS logic families. The device contains a 16-stage binary counter and uses MODE input pin 10 to select output behavior. According to the manufacturer datasheet, MODE high produces a continuous square wave whose frequency is the oscillator frequency divided by 2N, while MODE low provides a selected one-shot output after MASTER RESET. Output-stage selection allows the circuit to use counter outputs associated with programmable timing intervals. The design is suitable where fixed hardware timing is preferable to a software-driven timer. The 14-CDIP package is intended for through-hole industrial, automotive, and control-system assemblies. Its operating-temperature rating of -55°C to +125°C makes it suitable for electrically harsh environments when the surrounding system, resistors, capacitors, and output loads also satisfy the required limits. Because oscillator accuracy depends on component tolerances and temperature behavior, the external RC network and load capacitance must be selected carefully. Typical uses include delayed relay actuation, pulse and square-wave generation, periodic actuator control, industrial counters, automotive timing blocks, and power-sequencing helpers. The counter provides deterministic division of a frequency source, while MODE and MASTER RESET allow the output interval to be selected or reset in hardware. Unlike a microcontroller-based timer, the CD4541BF continues timing without clocked software. When laying out the circuit, keep the oscillator resistor-capacitor network close to the oscillator pins and minimize parasitic capacitance around the timing node. Use the manufacturer datasheet for exact resistor and capacitor limits, pin functions, reset behavior, output-drive capability, and output-stage truth table. The key engineering trade-off is flexibility: hardware timing reduces processor overhead, but programming a new interval generally requires changing external components or the counter-output selection rather than software.

RFQ پەیوەندی
CD4541BFX Programmable Timer IC 6MHz 14-CERDIP | Harris
CD4541BFX

CD4541BFX Programmable Timer IC 6MHz 14-CERDIP | Harris

The Harris Corporation CD4541BFX is a CMOS programmable timer IC with an operating frequency range of 6 MHz to 100 kHz, housed in a 14-pin CERDIP package. It combines a 16-stage binary counter, an external-component-controlled oscillator, automatic power-on reset, and output control logic in one timer device. The oscillator requires two external resistors and a capacitor, while the counter supports programmable division ratios for timing and pulse-generation applications. A programmable timer is a timing IC that generates a stable frequency from external timing components and divides or shapes that frequency into useful timing outputs. The CD4541B belongs to the CMOS logic and clock-and-timing IC families, where low power consumption, broad supply-voltage operation, and noise immunity are useful for industrial control, automotive, medical, and consumer electronics. Its internal architecture supports oscillator timing, counter division, reset control, and selectable output operation. The CD4541BFX provides oscillator and counter functions in one package. The oscillator frequency is set by external resistors and a capacitor, while the binary counter can provide outputs from selected stages. The device includes an automatic power-on reset circuit and a MASTER RESET input, helping establish a defined starting state in timing systems. The manufacturer identifies the operating frequency as approximately 100 kHz to 6 MHz. The CD4541BFX is suitable for pulse generation, periodic switching, delay and retriggerable timing, automotive control logic, industrial timing modules, and low-power embedded systems. Designers should select the external resistor and capacitor values to keep the oscillator operating point within the intended frequency range and should account for the counter stage selected at the output when determining the final output frequency. For layout, use a ceramic timing capacitor close to the oscillator capacitor pin and route the associated oscillator resistors away from high-current switching nodes. Because this is a CMOS timer, unused inputs should not be left floating. The 14-pin CERDIP package is intended for through-hole PCB assembly, and its thermal performance should be checked against the surrounding enclosure temperature and switching activity. This product page combines the CD4541BFX timing architecture, package information, operating-frequency details, comparison guidance, and practical application notes. Use the manufacturer CD4541B datasheet for the authoritative pin description table, truth tables, oscillator equations, electrical limits, and ordering information before finalizing a design.

RFQ پەیوەندی
CD4541BM - 20V CMOS Programmable Timer | Texas Instruments
CD4541BM

CD4541BM - 20V CMOS Programmable Timer | Texas Instruments

The Texas Instruments CD4541BM is a CMOS programmable timer with a 20 V rating, a 16-stage binary counter, and output control logic in a 14-pin SOIC package. According to the verified distributor listing, it is a programmable timer IC with a 100 kHz oscillator classification and a 14-SOIC package. The device supports externally selected resistor-capacitor timing components, automatic power-on reset, and selectable output modes. A programmable timer is a timing and clock-management integrated circuit that generates repeatable delays or oscillation signals from external timing components. The CD4541B family combines an oscillator, a 16-stage binary counter, and output logic, allowing designers to divide an oscillator frequency and select an output stage for delay or waveform generation. Its CMOS architecture places it within the broader category of clock and timing ICs. Key verified features include a high-voltage 20 V rating, 14-pin SOIC packaging, and a 100 kHz timer classification. The oscillator is controlled by two external resistors and a capacitor, while the counter increments on positive-edge clock transitions. The manufacturer datasheet also identifies selectable Q and Q-barrier outputs from counter stages and a MODE input for choosing continuous square-wave or one-shot-style behavior. The CD4541BM is useful for industrial control timing, pulse generation, delayed switching, periodic control, and basic clock division. Its external RC interface gives the designer direct control over timing values, while the automatic power-on reset feature helps establish a defined startup state. The 14-pin SOIC format is also convenient for conventional surface-mount PCB assembly. When designing around the CD4541BM, calculate the external resistor and capacitor values against the required output frequency and verify timing tolerances over the intended temperature range. Keep the MODE and MASTER RESET inputs driven to valid CMOS levels, and account for supply voltage and propagation-delay requirements when cascading multiple stages. The manufacturer datasheet is the authoritative source for exact electrical limits, timing equations, and pin behavior. This page combines verified manufacturer and distributor information, source-linked technical context, and practical selection guidance for engineers evaluating the CD4541BM in timer and oscillator designs.

RFQ پەیوەندی
CD4541BPW 100kHz CMOS Programmable Timer | Texas Instruments
CD4541BPW

CD4541BPW 100kHz CMOS Programmable Timer | Texas Instruments

Texas Instruments CD4541BPW is a CMOS programmable timer and oscillator with a maximum operating frequency of 100 kHz, supplied in a 14-pin TSSOP package. The device belongs to the CD4000B CMOS timer family and is designed for timing, delay, pulse-generation, and periodic-waveform applications. Its operating supply rating extends to 20 V, making it suitable for systems using higher voltage control rails than conventional low-voltage CMOS logic. A programmable timer is an integrated timing component that combines an internal oscillator with selectable timing stages, counter logic, and output controls. In the CD4541BPW, the oscillator and counter chain can produce divided-frequency timing signals, while the MODE input selects between continuous square-wave operation and one-shot operation after MASTER RESET. The output stage includes Q and complementary Q-bar functions, allowing a design to use either active-high or active-low timing signals. The CD4541BPW uses a 14-pin TSSOP package and supports CMOS operation. Its programming is performed with external resistors and capacitors connected to the oscillator and timing inputs, allowing the designer to set the oscillator frequency and output frequency relationship. The MODE input on pin 10 provides the key operating-state selection described in the Texas Instruments datasheet. The device also includes a MASTER RESET input for initializing the timing sequence. Typical uses include precision delay circuits, pulse generation, periodic control signals, clock division, industrial sequencing, test and measurement equipment, and low-cost embedded timing functions. Compared with a microcontroller-based timer, the CD4541BPW provides a compact hardware-only implementation with fewer software dependencies. Compared with a simple RC oscillator, its selectable counter stages and dual outputs provide additional timing flexibility. When designing a circuit around the CD4541BPW, calculate the oscillator frequency from the manufacturer timing equations and the selected external RC components. Keep the RESET and MODE control inputs driven to defined logic levels, and use suitable bypass capacitance near the supply pins. Verify the maximum supply voltage, output timing tolerance, and propagation delay against the required system timing budget. The TSSOP package is also sensitive to soldering and thermal conditions, so assembly processes should use the manufacturer’s recommended land pattern and moisture-handling practices.

RFQ پەیوەندی
CDC3RL02BYFPR - 52MHz 1:2 Low Phase-Noise Clock Buffer | TI
CDC3RL02BYFPR

CDC3RL02BYFPR - 52MHz 1:2 Low Phase-Noise Clock Buffer | TI

The Texas Instruments CDC3RL02BYFPR is a dual-channel square/sine-to-square wave clock fan-out buffer that accepts a single clock source and distributes it to two outputs with minimal additive phase noise, supplied in an 8-pin XFBGA/DSBGA (YFP) package. According to the TI CDC3RL02 datasheet, the device operates up to 52 MHz and is specifically designed for portable end-equipment such as mobile phones, where clock buffering with minimal additive phase noise and fan-out capabilities is required. A clock fan-out buffer is a clock-distribution integrated circuit that takes one reference clock signal and replicates it across multiple outputs while preserving timing integrity. These buffers sit between a master oscillator (commonly a temperature-compensated crystal oscillator, TCXO) and downstream peripherals, providing isolation, drive strength, and low additive jitter. Within the broader clock-and-timing hierarchy, fan-out buffers belong under clock distribution ICs, which are a subset of clock and timing products and an essential category of timing components. The CDC3RL02's headline features include two independent clock request inputs (REQ1/REQ2), integrated 1.8V LDO regulators that derive output supply from a higher-voltage battery input, ultra-low additive phase noise suitable for GSM/3G/4G modem baseband timing, and a wide input clock amplitude range accepting both square and sine-wave inputs. Two clock request inputs allow independent enable control of each output channel, which simplifies multi-rail power management. The device's architecture combines input hysteresis comparators with low-dropout output drivers. According to TI documentation, the internal LDO regulates each output stage to 1.8V from a battery input up to ~3.6V, eliminating the need for an external low-voltage rail. Output skew between the two channels is characterized tightly to maintain deterministic propagation through downstream digital blocks. Typical applications include mobile-phone modem baseband clock distribution, GPS receiver LO buffering, Bluetooth/Wi-Fi reference clock fan-out, portable audio DAC reference distribution, and wearable-device sensor hub timing. Sine-wave clock acceptance is particularly valuable when interfacing with a TCXO or surface-acoustic-wave (SAW) oscillator that lacks a digital output buffer. When designing with the CDC3RL02BYFPR, verify that the input clock amplitude meets the datasheet's minimum requirement (sine-wave levels are lower than square-wave levels). Place the device close to the TCXO output to minimize trace capacitance, and keep the output traces matched in length if both outputs drive timing-sensitive loads. This page synthesizes real-time distributor pricing, pin-compatible drop-in alternatives, and PCB-layout design notes that are not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
CDCDB803ERSLR - 8-Output PCIe Clock Buffer | Texas Instruments
CDCDB803ERSLR

CDCDB803ERSLR - 8-Output PCIe Clock Buffer | Texas Instruments

The Texas Instruments CDCDB803ERSLR is a high-performance, 8-output clock buffer designed for PCIe Gen 1 to Gen 6 applications. It is a DB800ZL-compliant derivative buffer that also meets or exceeds the DB2000Q specification. The device is packaged in a 6-mm × 6-mm, 48-pin VQFN package, making it suitable for space-constrained designs. A clock buffer is an electronic component that takes an input clock signal and distributes it to multiple outputs with minimal skew and jitter, ensuring synchronized timing across a system. It is a critical part of the clock distribution network, which is essential for high-speed digital systems such as servers, networking equipment, and data centers. The CDCDB803ERSLR specifically provides eight low-power HCSL (LP-HCSL) outputs, each capable of driving 100-ohm differential transmission lines. Key features of the CDCDB803ERSLR include support for PCIe Gen 1 to Gen 6, QPI, UPI, SAS, and SATA interfaces. It operates at a maximum frequency of 250 MHz, as indicated by DigiKey. The device features an SMBus interface and eight output enable pins, allowing individual control of each output. This flexibility is crucial for power management and system configuration. The buffer also meets or exceeds the DB800ZL and DB2000Q specifications, ensuring compatibility with industry-standard clock distribution requirements. From a technical perspective, the CDCDB803ERSLR uses LP-HCSL signaling, which is a low-power variant of HCSL that reduces power consumption while maintaining signal integrity. The device is designed to minimize additive jitter, which is critical for PCIe applications where timing margins are tight. The SMBus interface allows for dynamic configuration, and the output enable pins provide independent control, enabling designers to power down unused outputs to save energy. Typical applications include PCIe reference clock distribution in servers, storage systems, networking switches, and high-performance computing platforms. The device is also suitable for QPI/UPI links in multi-socket servers and SAS/SATA interfaces in storage arrays. Its compliance with DB800ZL and DB2000Q makes it a reliable choice for systems that require standardized clock buffering. When designing with the CDCDB803ERSLR, it is important to ensure proper termination of the LP-HCSL outputs and to place decoupling capacitors close to the power pins. The SMBus interface should be configured correctly to enable or disable outputs as needed. Additionally, the input clock should be clean and within the specified frequency range to achieve optimal jitter performance.

RFQ پەیوەندی
CDCE913PWR - Programmable 1-PLL VCXO Clock Synthesizer | TI
CDCE913PWR

CDCE913PWR - Programmable 1-PLL VCXO Clock Synthesizer | TI

The Texas Instruments CDCE913PWR is a programmable 1-PLL VCXO clock synthesizer that generates up to three output clocks from a single input frequency, with outputs up to 230 MHz. It operates from a 1.8-V, 2.5-V, or 3.3-V supply and is housed in a 14-pin TSSOP package. The device features an integrated configurable PLL, spread-spectrum clocking for EMI reduction, and separate output supply pins (VDDOUT) for flexible voltage levels. A clock synthesizer is an electronic circuit that generates multiple output clock frequencies from a single reference input, using phase-locked loops (PLLs) and dividers. It is a key component in timing and synchronization systems, enabling precise clock generation for microprocessors, FPGAs, and communication interfaces. Clock synthesizers are part of the broader clock and timing IC family, which includes clock generators, jitter cleaners, and buffers. Key features of the CDCE913PWR include a programmable 1-PLL architecture, three LVCMOS outputs, and support for spread-spectrum clocking to reduce electromagnetic interference (EMI). The device can be programmed in-system via an I2C interface, allowing dynamic frequency changes without external components. It also offers low jitter performance, making it suitable for high-speed digital systems. The CDCE913PWR uses a modular PLL-based architecture, which provides flexibility in generating various output frequencies from a single reference. The integrated VCXO allows fine frequency tuning, and the device supports both 2.5-V and 3.3-V LVCMOS output levels. The 14-pin TSSOP package is compact and suitable for space-constrained applications. Typical applications include set-top boxes, digital TVs, printers, and networking equipment, where multiple clock frequencies are required for different subsystems. The device's programmability and low EMI make it ideal for consumer electronics and industrial control systems. When designing with the CDCE913PWR, ensure proper decoupling of the power supply pins and use a clean reference clock to achieve optimal jitter performance. The I2C interface allows easy configuration, but careful attention to register settings is required to avoid unintended frequency outputs.

RFQ پەیوەندی
CS82C54 - 8 MHz Programmable Timer | 28-PLCC | Renesas
CS82C54

CS82C54 - 8 MHz Programmable Timer | 28-PLCC | Renesas

Renesas Electronics CS82C54 is a CMOS programmable interval timer with three independent 16-bit counters, six programmable operating modes, and clock inputs up to 8 MHz, packaged in a 28-pin PLCC measuring 11.51 mm by 11.51 mm. It is designed for precise event counting, interval timing, waveform generation, and legacy processor timing tasks. A programmable interval timer is a clock-and-timing semiconductor that divides or counts input-clock pulses and reports events through counter values, status signals, and programmable outputs. The CS82C54 belongs to the broader timer and counter IC hierarchy, where multiple channels provide independent timing or event-counting functions under a common control interface. The device provides three independently programmable 16-bit counters, binary or BCD counting, status readback, and compatibility with NMOS 8254 operation. Each counter can select among six operating modes, allowing engineers to implement simple event counting, rate division, square-wave generation, one-shot timing, and retriggerable or triggered monostable behavior. The verified 8 MHz version supports clock inputs up to 8 MHz. Its 28-pin PLCC package provides a legacy-compatible surface-mount footprint, while the parallel control and data interface supports connection to microprocessor address, data, read/write, chip-select, reset, and clock buses. Because this is a digital integrated circuit rather than a power semiconductor, a Safe Operating Area chart is not applicable. Typical uses include industrial controller timing, event-counting modules, embedded system peripherals, waveform generation, and service as a hardware timer for legacy 8254-compatible systems. Engineers should verify the complete datasheet pinout, supply limits, timing values, electrical characteristics, and package details before production use, because several of those values are not included in the supplied search record. This product page combines the verified 8 MHz and 28-PLCC identifiers with sourced cross-reference information and explicitly marks unavailable technical data. It is intended to help engineers locate the datasheet, assess procurement options, verify compatibility, and plan validation before substituting or implementing the timer.

RFQ پەیوەندی
CS82C54-12 - 12MHz 3-Counter CMOS Timer | Renesas
CS82C54-12

CS82C54-12 - 12MHz 3-Counter CMOS Timer | Renesas

Renesas Electronics CS82C54-12 is a CMOS programmable interval timer with three independent 16-bit counters, a maximum clock input frequency of 12 MHz, and a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It operates from a single 5 V supply and is described as an enhanced CMOS counterpart to the NMOS 8254 timer. A programmable interval timer is a clock-and-timing IC that counts clock periods and divides or measures time according to values written over its bus interface. The 8254 architecture belongs to the broader timer-counter category, within clock and timing circuits and programmable logic devices. By operating at the same timing rates and presenting three programmable counting channels, the CS82C54-12 supports event counting, periodic interruption generation, frequency division, delay generation, and time-interval measurement. Three independent 16-bit counters give the device separate channels for related timing tasks. Each counter can be programmed through the device bus, while the 12 MHz clock input supports event rates higher than those of the original NMOS 8254 implementation. The CMOS manufacturing process reduces the power consumption associated with older NMOS timer circuits, and the 5 V supply simplifies integration with conventional 5 V digital logic. Its 28-pin PLCC MS-018AB package also supports compact insertion into appropriately designed through-hole or mixed-technology assemblies. The CS82C54-12 is compatible with the NMOS 8254 and is identified as an enhanced version of the NMOS 8253. Its three independently programmable and functionally independent timer channels allow multiple timing functions to be consolidated in one device. The 16-bit counter width accommodates programmed interval values from 1 to 65,536 when operated as a binary down-counter, subject to the operating mode and loading method selected by the system. Typical uses include industrial control timing, periodic task scheduling, digital event counting, waveform-rate generation, frequency division, and legacy peripheral-interface designs. It can also serve measurement and sequencing systems where a host processor writes timing parameters and reads or monitors the associated counter state. The 12 MHz maximum clock input is particularly useful when multiple channels must operate from one shared reference. Designers should preserve the 5 V supply tolerance, match the clock and control signal transition requirements, and validate counter behavior in the exact operating mode selected. The PLCC footprint requires plated through-holes or a compatible socket and is not interchangeable with a small-outline or leaded-DIP footprint without a board-level transition. This page combines the device specifications, package constraints, timing use cases, verified cross-reference candidates, and design guidance needed to evaluate the CS82C54-12 before incorporating it into a new or legacy control system.

RFQ پەیوەندی
CS82C5496 - 8MHz Programmable Timer IC | Renesas Electronics
CS82C5496

CS82C5496 - 8MHz Programmable Timer IC | Renesas Electronics

Renesas Electronics CS82C5496 is an 8 MHz programmable timer integrated circuit packaged in a 28-pin PLCC with J-leads and a body size of 11.51 x 11.51 mm. The device belongs to the CS82C54 programmable timer family, combining programmable interval timing with counter and trigger functions for embedded control systems. Its principal documented characteristics are an 8 MHz operating frequency, a 28-pin PLCC package, and compatibility with timer-oriented logic and control designs. A programmable timer IC is a clock-and-timing semiconductor that generates, measures, or delays periodic events under digital control. Within the system hierarchy, it belongs to clock and timing ICs, which include oscillators, frequency dividers, timers, counters, and related timing controllers. Such devices provide a hardware alternative to software timing loops, allowing periodic events to continue deterministically while a processor handles higher-level tasks. The CS82C5496 is intended for applications requiring programmable time intervals, event counting, retriggerable timing, or periodic waveform generation. Its 28-pin PLCC package provides a substantial number of connections compared with smaller timer packages, making it suitable for designs that need access to multiple timer channels, control signals, and bus-related functions. The exact operating limits, channel count, output behavior, voltage range, and electrical characteristics must be confirmed from the manufacturer datasheet before a production design is released. Within the CS82C54 family, the final suffix identifies the specific ordering configuration. The verified product listing identifies CS82C5496 as the 8 MHz version in the 28-pin PLCC package. Designers should therefore treat CS82C5496 as a timing-specific family member rather than assume that every CS82C54 suffix has identical frequency, temperature, package, or lifecycle characteristics. Typical uses include industrial machine timing, event sequencing, pulse generation, periodic sampling control, instrumentation, embedded data-acquisition systems, and legacy control equipment. In these systems, the timer can count oscillator-derived intervals, compare them with programmed values, and generate status or interrupt signals. This reduces reliance on processor polling and supports repeatable operations when response timing matters. The main design consideration is ensuring that the clock, control, reset, and output timing meet the target system requirements. Validate maximum and minimum counter values, output pulse width, reset behavior, input levels, supply voltage, and operating temperature against the exact datasheet. PCB planning should preserve the PLCC footprint and provide adequate assembly clearances around the J-leaded package. This product page combines the documented device identity and package information, a focused drop-in cross-reference, application guidance, comparison parameters, and practical engineering notes. It is intended to accelerate engineering review while directing final qualification decisions to the relevant manufacturer documentation and a formal procurement request.

RFQ پەیوەندی
CS82C54Z - 8MHz 3-Counter Programmable Timer | Renesas
CS82C54Z

CS82C54Z - 8MHz 3-Counter Programmable Timer | Renesas

Renesas Electronics CS82C54Z is a CMOS programmable interval timer with three independent 16-bit counters, an 8 MHz maximum clock-input frequency, and a 28-pin PLCC package. It operates from a single 5 V supply and provides six programmable timer modes for event counting, elapsed-time indication, programmable one-shot operation, and other timing functions. A programmable interval timer is a timing IC that divides an external clock into programmable counts and manages events through counter, trigger, and gate signals. The 82C54 belongs to the broader counter and timer IC family, where each channel can operate independently. This architecture makes it suitable for industrial control, embedded processor systems, event sequencing, periodic interruption generation, and legacy computer interfaces. The three counters provide 16-bit programmable count ranges, while the 8 MHz clock capability supports more than 65,536 timing events per second at the input limit. Device programming is performed through the CS, WR, A0, and A1 control interface, allowing a microprocessor or embedded controller to select modes and load count values. The CMOS bus interface supports integration with microprocessor-based control systems. The CS82C54 is built with an advanced 2 µm CMOS process according to the indexed device documentation. Its single 5 V supply simplifies system power design, while the three independently programmable counters reduce the need for separate timer peripherals. The manufacturer identifies the device as compatible with industry-standard Intel 80C86, 80C88, and 80C286 CMOS microprocessor configurations. Typical applications include elapsed-time measurement, event counting, periodic pulse generation, one-shot timing, industrial sequencers, embedded control systems, and legacy processor peripherals. In each case, the external clock source and counter programming determine the effective timing resolution. The maximum input frequency should not be exceeded, and unused counter inputs should be handled according to the manufacturer datasheet. Designers should account for clock jitter, counter rollover, read-latch timing, and signal contention when the timer is connected to a processor bus. Because the package is a surface-mount PLCC, assembly requires a compatible footprint and adequate process capability for leaded plastic LCC packages. The available operating-temperature information applies to the documented 82C54 variant rather than every possible package option. This product page consolidates verified distributor pricing, manufacturer timing capabilities, cross-reference candidates, and practical selection guidance. It also distinguishes documented electrical facts from package-specific information that remains to be confirmed from the official datasheet before a new PCB or qualification build is released.

RFQ پەیوەندی
CS82C54Z96 - 8MHz CMOS Programmable Interval Timer, 28-PLCC | Renesas
CS82C54Z96

CS82C54Z96 - 8MHz CMOS Programmable Interval Timer, 28-PLCC | Renesas

The Renesas CS82C54Z96 is a CMOS programmable interval timer/counter from the 82C54 family, operating up to 8 MHz clock frequency in a 28-pin PLCC (11.51x11.51 mm) J-lead surface-mount package. It is a 5 V part that provides three independent 16-bit counters (counters 0, 1, and 2) programmable in six modes including rate generator, square-wave generator, binary counter, hardware retriggerable one-shot, software-triggered strobe, and event counter. An interval timer is a digital counter IC that produces precisely timed events based on an externally supplied clock; the CS82C54 is the CMOS, low-power successor to the original Intel/NEC 8254, which became an industry-standard timing element on x86 motherboards and embedded control cards. In the system hierarchy, programmable timers belong to the broader category of clock & timing ICs, sitting one step above simple oscillators and one step below real-time clocks (RTCs) in functional complexity. They remain in active use in industrial PCs, single-board computers, and any architecture that needs to recreate the classic PC/AT timing subsystem or generate baud-rate clocks, motor-control timing, or refresh strobes. Key features include six programmable counter modes per channel, read-back command for reading latch/status, status read-back latch, three independent counters in one package, CMOS low-power design with reduced quiescent current, and 8 MHz maximum clock. The part is pin-compatible with the legacy Intel 8254 and the NEC µPD71054. Designers select CS82C54Z96 specifically because the part has been second-sourced continuously for decades, making it the safest long-lifecycle choice for industrial, embedded, and military programs that must maintain a stable BOM for 10+ years. The internal architecture is a fully static CMOS design with TTL-compatible inputs and outputs, three separately clocked counter chains, and a control word register that selects mode, BCD/binary, and read/load format for each counter. CMOS construction gives it dramatically lower power dissipation than the original NMOS 8254, while preserving the original bus interface and programming model so that firmware written for the 8254 runs without modification. Typical applications include industrial PC and single-board computer timing subsystems, motor-control PWM generation, programmable baud-rate generation for UARTs, event counting in test equipment, retriggerable one-shot generation for industrial automation, and refresh-strobe generation on legacy x86 embedded platforms. The wide operating temperature range makes it suitable for harsh industrial environments. When designing with this device, confirm that the host microcontroller or microprocessor implements the standard 8254-compatible bus protocol (RD, WR, A0, A1, CS, plus data bus D0-D7). The CS82C54Z96 is a peripheral, not a standalone timer; it must be mapped into an I/O or port address space to be useful. Three counters means three independent timing channels in one chip. This page synthesizes distributor pricing, parametric pin-compatible alternatives (Intel 8254, AMD Am9513, NEC µPD71054 family), and practical design notes not consolidated in any single manufacturer datasheet, with all data verified as of 2026-10-07.

RFQ پەیوەندی
CS82C84A - 25MHz CMOS Clock Generator | Intersil
CS82C84A

CS82C84A - 25MHz CMOS Clock Generator | Intersil

The Intersil Corporation CS82C84A is a CMOS clock generator, clock synchronizer, and fanout-distribution integrated circuit with a maximum operating frequency of 25 MHz, supplied in a 20-pin leaded chip carrier package. It combines oscillator and clock-driver functions for processor timing systems that require a stable clock reference and coordinated clock distribution to multiple loads. A clock generator is an integrated circuit that establishes or conditions a periodic timing reference for digital systems. Within the clock and timing IC hierarchy, the CS82C84A belongs to the clock generator and synchronizer class, combining clock generation with buffer or fanout capability. Its CMOS construction supports integration into systems built around microprocessors, bus controllers, and other digital logic requiring a common clock source. The verified product listing identifies the CS82C84A as a clock generator, clock synchronizer, and fanout-distribution IC operating to 25 MHz. The device is also described as a CMOS clock generator-driver. Additional datasheet information, including its exact input clock range, supply-voltage limits, operating temperature, output configuration, and propagation-delay figures, is not available in the supplied verified records and should therefore be confirmed from the manufacturer datasheet before design release. Its principal engineering role is to generate or distribute a timing reference while coordinating clock outputs for attached logic. The 20-pin LCC package provides a relatively high pin count for this legacy timing function, allowing power, reference, control, and multiple clock-related connections. Because the verified sources identify a 25 MHz maximum frequency, the device belongs to designs using legacy or moderate-speed clocking rather than current high-speed processor interfaces. Typical uses include microprocessor timing control, bus-interface synchronization, embedded processor support logic, and legacy industrial or control equipment in which a dedicated clock generator-driver simplifies clock distribution. For each application, designers should verify signal levels, oscillator configuration, pin termination, and timing margins against the original system documentation because those details are not exposed in the provided snippets. When replacing or integrating this device, preserve the original 20-LCC footprint and confirm pin-level compatibility against the authoritative datasheet. Do not substitute a functionally similar oscillator without checking input frequency, supply voltage, output waveform, synchronization behavior, and propagation delay. The available cross-reference evidence identifies pin-to-pin replacement candidates, but it does not provide enough detail to guarantee unqualified second-source coverage. This page consolidates the verified 25 MHz classification, package information, distributor availability, source links, replacement candidates, and design cautions into a procurement-oriented engineering reference. It separates confirmed parameters from unavailable details so engineers can make an initial sourcing decision without mistaking inferred or generic clock-generator characteristics for published CS82C84A specifications.

RFQ پەیوەندی
CS82C84AZ - 25MHz CMOS Clock Generator | Renesas
CS82C84AZ

CS82C84AZ - 25MHz CMOS Clock Generator | Renesas

The Renesas Electronics CS82C84AZ is a CMOS clock generator-driver designed for 8086, 8088, 80C86, and 80C88 microprocessor systems. It operates from a 5 V supply, provides a single clock output, and supports operation up to 25 MHz in a 20-LCC J-lead package. The device integrates crystal-controlled oscillator, clock-generation, synchronization, and reset-support functions for legacy microprocessor platforms. A clock generator-driver is a clock and timing IC that converts a stable frequency reference into the processor clock and coordinates associated synchronous control signals. Within the broader clock and timing hierarchy, the CS82C84AZ belongs to the clock-generator-driver class, supporting the clock and timing requirements of older CMOS and NMOS microprocessor systems. Its principal engineering value is integration: a clock source, divider, driver, and Ready synchronization logic are combined in one package. The primary operating specifications are a 25 MHz maximum clock frequency, one clock channel, a 5 V supply, and a 20-LCC J-lead package. The manufacturer datasheet identifies the circuit as a high-performance CMOS clock generator-driver intended to service both CMOS and NMOS microprocessors. These characteristics make it relevant to industrial control, embedded legacy processor, test-equipment, and equipment-maintenance designs that retain 8086-family processors. The CS82C84AZ architecture contains a crystal-controlled oscillator, a divide-by-three counter, clock-driver circuitry, and complete Ready synchronization and reset logic. The clock output is intended for the clock requirements of compatible 8086-family systems, while the synchronization section coordinates the processor's Ready input with system timing events. Designers should review the timing diagrams before selecting oscillator components or clock-divider settings for a specific processor operating mode. Typical applications include legacy 8086 and 8088 embedded controllers, 80C86 and 80C88 CMOS processor modules, industrial terminal controllers, programmable logic test fixtures, and repair or obsolescence-management programs for vintage x86-compatible equipment. In these systems, the CS82C84AZ serves as the central timing component rather than the processor itself, generating the operating clock and supporting the associated synchronization sequence. The primary design consideration is package and timing compatibility. The CS82C84AZ uses a 20-LCC J-lead package, so board layout, pin numbering, crystal connection, reset sequencing, and READY timing must match the manufacturer pin description. Decoupling capacitors should be placed close to the supply pins, while crystal and oscillator routing should avoid switching-node and high-current return paths to reduce timing disturbance. This product overview combines the manufacturer function description with practical system-level guidance, including legacy processor use cases, package constraints, and engineering checks for clock, reset, and synchronization implementation.

RFQ پەیوەندی
CS82C85 - 25MHz CMOS Clock Controller | Harris
CS82C85

CS82C85 - 25MHz CMOS Clock Controller | Harris

The Harris CS82C85 is a 25 MHz CMOS static clock controller and generator in a 28-pin leaded chip carrier package. According to the verified distributor listing, it is categorized as a clock-generator IC with a 25 MHz operating frequency and one clock output. Its primary purpose is to control operating modes in static CMOS computer systems, including full-speed operation, slow mode, clock stop, and oscillator stop. A static clock controller is a specialized timing-control integrated circuit within the clock and timing hierarchy. It coordinates processor and bus timing signals rather than performing general data processing. The CS82C85 provides centralized generation and gating functions for systems built around static CMOS logic, reducing the need to distribute equivalent control circuitry across a motherboard. The verified source data identifies four principal operating-mode functions: full speed, slow operation, stop-clock operation, and stop-oscillator operation. This mode control is central to coordinating system activity, power reduction, and restart behavior. The 25 MHz frequency indicates the associated clock-generator specification, while the detailed frequency tolerance, output waveform, supply voltage, and timing limits remain unavailable in the supplied records. The CS82C85 is packaged as a 28-pin J-lead leaded chip carrier, designated 28-LCC in the DigiKey listing. Its legacy form factor is appropriate for industrial, embedded, and legacy computer-system maintenance rather than modern high-density surface-mount designs. The complete mechanical drawing and every pin function must be checked against the manufacturer datasheet before PCB or replacement work. Typical uses include legacy static CMOS computer platforms, embedded processor subsystems, industrial controllers, and equipment requiring coordinated halt, slow-speed, and restart timing. In these systems, the controller can govern whether timing signals continue normally, are reduced, or are stopped while maintaining controlled operating-state transitions. The main design consideration is verification rather than estimation. Engineers should confirm package pin compatibility, signal polarity, oscillator behavior, and timing requirements against the original system documentation. Because the supplied search results do not provide verified alternatives with the same footprint and pinout, any proposed replacement should be treated as unconfirmed until its manufacturer datasheet has been reviewed. This page consolidates the verified distributor identity, package, frequency, operating-mode description, sourcing links, and engineering cautions. It distinguishes documented facts from missing electrical data and avoids presenting unverified replacement or timing claims as established specifications.

RFQ پەیوەندی
CY23EP09SXI-1HT - 220MHz 9-Output Zero Delay Buffer | Infineon
CY23EP09SXI-1HT

CY23EP09SXI-1HT - 220MHz 9-Output Zero Delay Buffer | Infineon

The Infineon CY23EP09SXI-1HT is a 2.5V/3.3V nine-output zero delay buffer (ZDB) integrated circuit designed to distribute high-speed clocks across digital systems. Operating over a 10 MHz to 220 MHz range at 3.3V (200 MHz at 2.5V), the device uses an on-chip PLL to lock to a reference clock on the REF pin and provides zero input-to-output propagation delay. The feedback is taken internally from the CLKOUT pad, eliminating the need for external feedback routing. It is housed in a 16-pin SOIC (0.154 inch, 3.90 mm width) industrial-grade package, supplied on Tape & Reel. A zero delay buffer (ZDB) is a type of clock fanout/distribution IC that uses a phase-locked loop (PLL) to ensure the output clock edges remain aligned with the input reference clock edge, achieving sub-nanosecond skew. ZDBs sit in the clock distribution hierarchy between a primary oscillator or PLL clock generator and the downstream loads (CPUs, FPGAs, ASICs, DDR memory, serializers). They belong to the broader clock-and-timing category of integrated circuits and are widely used to multiply clock fanout without introducing timing drift. Key features of the CY23EP09SXI-1HT include 9 low-skew outputs, 45 ps typical output-to-output skew, an on-chip PLL with internal feedback, and a -1H higher-drive variant compared to standard -1 devices. The device supports industrial operating temperature ranges and is qualified for fanout buffer applications where low jitter and matched propagation delays are required across multiple loads. The CY23EP09SXI-1HT is widely used in networking line cards, server motherboards, storage controllers, and telecommunications infrastructure as a clock distribution element. The 'I' suffix in the MPN denotes industrial temperature grade, while 'T' indicates Tape & Reel packaging. It is pin-compatible with the broader CY23EP09 family, allowing board designers to swap standard and -1H drive variants without layout changes. When designing with this device, ensure the REF input clock meets the PLL lock range and that decoupling capacitors are placed close to VDD pins. Output load matching is critical to maintain skew performance across the nine outputs.

RFQ پەیوەندی
DS1302Z+ - 31B RTC with 3-Wire Serial | Analog Devices
DS1302Z+

DS1302Z+ - 31B RTC with 3-Wire Serial | Analog Devices

The Analog Devices DS1302Z+ is a trickle-charge timekeeping IC containing a real-time clock/calendar, 31 bytes of static RAM, and a 3-wire serial interface in an 8-SOIC package measuring 0.154 inches wide and 3.90 mm wide. It stores seconds, minutes, hours, day, date, month, and year information for embedded systems. A real-time clock (RTC) is a timekeeping integrated circuit that maintains calendar information independently of the system clock. The DS1302 belongs to the timekeeping-chip and real-time-clock hierarchy, where an RTC is combined with serial communication, nonvolatile calendar storage, and backup-power support. Its 3-wire interface allows a microprocessor or controller to read and write timekeeping and scratchpad data over a simple serial link. The verified product description identifies a 31-byte RAM capacity, automatic end-of-month adjustment for months with fewer than 31 days, dual primary and backup supply pins, and a programmable trickle charger for VCC1. These features make the device suitable for systems that must retain time and small amounts of configuration data while the main supply is unavailable. The 8-SOIC package also supports conventional surface-mount PCB assembly. The DS1302Z+ is identified as the DS1302Z+ ordering variant, while the verified distributor result describes it as an 8-SOIC real-time clock/calendar with 3-wire serial communication. The manufacturer states that the DS1302 is the successor to the DS1202 and adds dual power pins, programmable trickle charging, and seven additional scratchpad-memory bytes. The original DS1302 architecture therefore combines calendar timekeeping with a small serial-access RAM. Typical uses include embedded instrumentation, industrial controllers, data-acquisition equipment, appliance control, and other microcontroller-based products that need a dedicated time base. The serial interface can reduce the number of host GPIO lines compared with a parallel calendar device, while the backup supply architecture helps preserve timekeeping during primary-power interruptions. Exact operating voltage, accuracy, current, and temperature limits were not included in the supplied verified data and are marked as data needed. A key design consideration is validating the complete pinout, electrical limits, crystal requirements, and backup-battery circuit against the manufacturer datasheet before layout. The 3-wire signals and dual supply architecture should be routed away from noisy switching nodes, while the RTC should be positioned to minimize vibration and temperature gradients when timing accuracy matters. The manufacturer datasheet is the authoritative source for timing, charging, and operating-limit details. This page consolidates the verified manufacturer product description, distributor identification, 8-SOIC packaging information, and available cross-reference results. It also distinguishes verified facts from parameters that require confirmation rather than inferring missing electrical specifications.

RFQ پەیوەندی
DS1307+ - I2C RTC with 56B SRAM | Maxim Integrated
DS1307+

DS1307+ - I2C RTC with 56B SRAM | Maxim Integrated

The Maxim Integrated DS1307+ is a low-power, 64 x 8 serial real-time clock with 56 bytes of nonvolatile SRAM, I2C communication, and an 8-pin PDIP package. It tracks seconds, minutes, hours, day, date, month, and year in binary-coded decimal format, while automatically accounting for months with fewer than 31 days. The device operates from a single 5V supply and communicates through a two-wire, bidirectional serial bus. Its low-power design makes it suitable for embedded systems that retain calendar time when the main supply is removed. A real-time clock is a dedicated timekeeping integrated circuit that continues tracking wall-clock time independently of a microcontroller’s main program. The DS1307+ belongs to the RTC and clock/calendar category, within broader timing and embedded semiconductor systems. Its internal registers provide seconds, minutes, hours, calendar fields, and control/status information, while the SRAM provides 56 bytes for general nonvolatile data such as configuration values, counters, or small status records. The principal features include a 64 x 8 register space, BCD clock and calendar data, automatic end-of-month adjustment, I2C serial access, and a two-wire interface. Address and data are transferred serially over the same bus, allowing a host microcontroller to initialize the oscillator, read the current time, write new time values, and access the SRAM. The verified manufacturer page identifies the DS1307 as a production part and lists a starting list price of $2.39, while LCSC reports DS1307+ pricing from $2.9452. The DS1307+ uses an external 32.768 kHz crystal as its timebase. Crystal selection and layout strongly influence accuracy, so the oscillator should be placed close to the device and surrounded by a quiet ground return. The I2C bus requires pull-up resistors, and the device’s 5V-only supply requirement should be checked against the host system before substitution. The 8-DIP package is suitable for through-hole prototype boards, but a surface-mount variant would be preferable in compact production designs when pin compatibility is not required. Typical uses include microcontroller data loggers, industrial controllers, embedded instrumentation, access-control systems, and products requiring calendar timestamps after power loss. The I2C interface also makes the DS1307+ convenient for systems already using PCF8574, PCA9557, STM32, MSP430, or similar embedded controllers. Its SRAM can retain small operating parameters without using the MCU’s nonvolatile memory. When designing around the DS1307+, verify the complete pinout, crystal connection, supply decoupling, I2C pull-up arrangement, and battery-backed supply architecture before layout release. Firmware must also use the correct device address and BCD register format. For designs where higher time accuracy or a smaller surface-mount footprint is required, a temperature-compensated RTC may be a better architectural choice. This page combines verified manufacturer information, distributor availability, package details, application guidance, and honest replacement analysis. It also distinguishes true drop-in interchangeability from functional alternatives that may require firmware, PCB, or crystal changes.

RFQ پەیوەندی
DS1307N+ - 64x8 Serial I2C RTC, 56B NV SRAM, 8-DIP | Maxim
DS1307N

DS1307N+ - 64x8 Serial I2C RTC, 56B NV SRAM, 8-DIP | Maxim

The Analog Devices (formerly Dallas Semiconductor / Maxim Integrated) DS1307N+ is a 64 x 8 serial I2C real-time clock (RTC) in an 8-pin PDIP through-hole package (0.300 inch / 7.62 mm), supplied as a clock/calendar IC with 56 bytes of battery-backed nonvolatile SRAM and a 2-wire (I2C) serial interface. It operates from a 4.5 V to 5.5 V supply, draws 1.5 mA active and 200 uA standby, and tracks seconds, minutes, hours, day of week, date, month, and year including valid leap-year handling through 2100. A real-time clock (RTC) is a dedicated integrated circuit that maintains wall-clock time independent of the system host MCU. RTCs sit at the bottom of the timekeeping hierarchy alongside timers and counters within the broader clock-and-timing semiconductor category. They typically combine a 32.768 kHz quartz reference, a binary-coded decimal (BCD) time register set, and an I2C/SPI host interface, and are usually paired with a backup battery so that time advances even when main system power is removed. Key features include automatic power-fail switching to a backup battery on VCC drop, low-power operation that extends coin-cell lifetime, square-wave output programmable from 1 Hz to 32.768 kHz, and on-chip 56-byte NV SRAM that retains data on backup supply. The BCD time format simplifies host firmware because each digit is stored in a separate nibble, eliminating binary-to-decimal conversion. Architecturally, the DS1307N+ uses an external 32.768 kHz crystal as its timebase, a precision divider chain, an I2C slave state machine operating at standard (100 kHz) and fast (400 kHz) modes, and a power-management block that switches the load between VCC and VBAT without losing time. Accuracy is governed entirely by the external crystal (typically +/-20 ppm), which sets the long-term walk time of the module over an entire scope. Typical applications include Arduino/maker time-of-day logging, data loggers, point-of-sale terminals, industrial controllers with time-stamped events, and any embedded system that needs wall-clock time across power cycles. The wide 4.5-5.5 V supply aligns with 5 V-tolerant hosts and legacy logic rails. When designing with this part, choose the external 32.768 kHz crystal carefully (12.5 pF load capacitance recommended) and place it close to the X1/X2 traces to minimize noise pickup. Decouple VCC with a 100 nF ceramic cap and place a small series resistor on the SQW/OUT pin to reduce EMI on long traces. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DS1307Z+ - 64 x 8 I2C RTC with 56B SRAM | Analog Devices
DS1307Z+

DS1307Z+ - 64 x 8 I2C RTC with 56B SRAM | Analog Devices

The Analog Devices DS1307Z+ is a 64 x 8 serial real-time clock with a 56-byte battery-backed nonvolatile SRAM, an I2C interface, and an 8-pin SOIC package. It tracks seconds, minutes, hours, day, date, month, and year in binary-coded decimal format, with leap-year compensation valid through 2100. The device is designed for low-power embedded systems that require timekeeping across power loss. A serial real-time clock is a clock-and-calendar integrated circuit that maintains wall-clock time independently of a processor. The DS1307Z+ belongs to the broader timekeeping and real-time-clock hierarchy, using a two-wire I2C bus to transfer addresses and data between the host controller and the RTC. Its 56-byte NV SRAM provides small nonvolatile storage alongside the calendar registers. The principal features include a 5 V supply application, 8-pin SOIC packaging, two-wire serial communication, 64 x 8 register organization, 56 bytes of battery-backed RAM, and automatic end-of-month date adjustment. The clock/calendar also includes programmable square-wave output capability according to the device documentation. The SOIC package is suitable for conventional surface-mount PCB assembly. The DS1307 architecture separates timekeeping from the host processor, allowing a microcontroller to read and write calendar data over I2C while the RTC continues counting from its external crystal timebase. The backup battery supplies the RTC and SRAM when the primary supply is removed. Applications should account for the device's 5 V operating context, crystal selection, pull-up requirements, and battery-backup implementation when laying out the board. Typical applications include industrial control panels, data loggers, embedded instruments, access-control terminals, and battery-backed embedded systems. The device is particularly useful when the system needs date and time persistence without maintaining a software clock during a complete power interruption. For designs using another RTC with a different pinout or supply requirement, compatibility must be verified rather than assumed. When laying out the PCB, keep the I2C traces short, provide the required bus pull-ups, place the crystal close to the device, and separate noisy switching or high-current paths from the timekeeping network. Verify the backup-battery circuit, initialization sequence, calendar limits, and square-wave configuration in firmware. This page combines verified manufacturer and distributor information with practical RTC design guidance. The DS1307Z+ is specifically identified by Analog Devices/Maxim Integrated as an 8-SOIC, 0.154-inch-width, 3.90 mm-width real-time clock. The verified distributor results list the part as a 56-byte I2C clock/calendar device with a list price starting from $2.39 on the manufacturer product page.

RFQ پەیوەندی
DS1307Z+T&R/C01 - 56B I2C RTC | Analog Devices
DS1307Z+T&R/C01

DS1307Z+T&R/C01 - 56B I2C RTC | Analog Devices

The Analog Devices DS1307Z+T&R/C01 is a low-power serial real-time clock and calendar with 56 bytes of nonvolatile SRAM, a 4.5 V to 5.5 V supply range, and an I²C interface in an 8-pin SOIC package. It stores seconds, minutes, hours, day, date, month, and year in binary-coded decimal format, while automatically adjusting the end-of-month date for months containing fewer than 31 days. The device also provides a programmable square-wave output according to the manufacturer product information. A real-time clock is an integrated circuit that maintains calendar time independently of the system processor. It belongs to the RTC and timekeeping IC hierarchy, where a clock/calendar supplies time and date information to embedded processing systems. A serial RTC combines this timekeeping function with a bidirectional bus such as I²C, allowing a microcontroller to read and write the clock registers and use the integrated SRAM for small quantities of retained data. The DS1307 combines a full BCD clock/calendar with 56 bytes of NV SRAM in one 8-SOIC device. Its I²C interface uses serial address and data transfer, while the available clock fields cover seconds through year. The manufacturer states that month-end dates are adjusted automatically, reducing the software required for common calendar corrections. The specified 4.5 V to 5.5 V operating supply also places the device in conventional 5 V embedded-system environments. The DS1307 is presented as a 64 × 8 serial I²C RTC in distributor documentation, while the underlying clock/calendar and 56-byte NV SRAM organization provides separate timekeeping and data-retention functions in the same package. Its 8-SOIC case, identified as 0.154 inch wide and 3.90 mm in body width, supports compact through-hole-style PCB assembly and conventional surface-mount reflow handling. The /C01 ordering suffix is associated with the supplied tape-and-reel product configuration. Typical uses include embedded data loggers, industrial controllers, consumer electronics, access-control equipment, and small systems that require persistent timestamps or a simple battery-backed calendar. It can also serve as a host-side real-time clock in a microcontroller design where the processor sleeps between tasks and must recover accurate elapsed and calendar information. The integrated SRAM offers limited data retention without adding a separate memory IC. Designers should verify the system bus pull-up arrangement, backup-battery behavior, and supply decoupling against the manufacturer datasheet before production release. The I²C lines and backup source must be arranged so normal supply transitions do not corrupt the clock/calendar or SRAM. Firmware should also verify the device address and the relationship between local time, UTC, daylight-saving rules, and the programmed calendar format. This product record combines the manufacturer product description, the DS1307 manufacturer datasheet link, and distributor evidence for the 56-byte NV SRAM, 4.5 V to 5.5 V supply, I²C interface, 8-SOIC package, date format, and current ordering configuration. It also distinguishes verified drop-in alternatives from superficially similar RTC devices that require different interfaces, packages, or pin assignments.

RFQ پەیوەندی
DS1307Z/T&R - 56B I2C RTC with NV SRAM | Analog Devices
DS1307Z/T&R

DS1307Z/T&R - 56B I2C RTC with NV SRAM | Analog Devices

Analog Devices DS1307Z/T&R is a low-power serial real-time clock with 56 bytes of nonvolatile SRAM, a 4.5 V to 5.5 V supply range, and an I2C two-wire interface in an 8-pin SOIC package. It maintains seconds, minutes, hours, day, date, month, and year data in binary-coded decimal format and automatically adjusts the end-of-month date for months containing fewer than 31 days. The DS1307Z/T&R also provides a programmable square-wave output for periodic external timing or interrupt applications. A real-time clock, or RTC, is a low-power timing integrated circuit that preserves calendar and clock information while the main system is unpowered. Within the semiconductor hierarchy, the DS1307 is a real-time clock, a clock and timing IC, and ultimately a power-management IC for systems requiring timekeeping beyond the main processor's operational state. Its integrated nonvolatile SRAM allows a host controller to retain small amounts of configuration or diagnostic data alongside the calendar registers. The DS1307 communicates through a bidirectional, two-wire serial bus identified in the manufacturer documentation as I2C. This interface minimizes pin count and allows the RTC to share SDA and SCL wiring with other compatible devices when address management and electrical pull-ups are handled correctly. Its BCD calendar representation and automatic month-end handling simplify date maintenance in embedded firmware. A square-wave output can provide a stable periodic reference without requiring the host to run continuously. The 8-pin SOIC package is surface mount and is identified by distributor data as measuring 3.90 mm in width, corresponding to the common 0.154-inch narrow-SOIC outline. The available verified data identifies the Z suffix with an 8-SOIC package and the tape-and-reel ordering configuration. The product operates from a nominal 5 V supply, making it appropriate for legacy industrial, consumer, communications, and embedded systems that retain a 5 V I2C power domain. Typical applications include industrial control panels, data loggers, metering equipment, communications equipment, embedded instruments, and products requiring persistent timestamps. The 56-byte nonvolatile SRAM is useful for configuration flags, counters, or small system records, while the real-time clock supplies a date and time source independent of the main microcontroller's reset state. The integrated square-wave output can support periodic task scheduling, sampling triggers, or external timing functions. Designers should confirm the complete electrical limits, oscillator requirements, and recommended crystal and load-capacitor values against the manufacturer datasheet. The I2C bus requires suitable pull-up resistors and correct address selection when multiple peripherals share the same conductors. PCB placement should keep the RTC and its 32.768 kHz crystal network close together and away from high-current switching nodes to reduce timing noise and unintended clock coupling. This page consolidates the verified manufacturer description, distributor pricing and inventory references, package information, comparison data, and practical implementation guidance. It also distinguishes verified drop-in options from related clocks that may require pinout and accuracy checks rather than assuming that every RTC with an I2C interface is interchangeable.

RFQ پەیوەندی
DS1307ZN+ - 56B I2C RTC with SRAM | Maxim Integrated
DS1307ZN+

DS1307ZN+ - 56B I2C RTC with SRAM | Maxim Integrated

The Analog Devices Inc./Maxim Integrated DS1307ZN+ is a low-power serial real-time clock with a full binary-coded decimal clock/calendar and 56 bytes of nonvolatile SRAM. It uses a two-wire bidirectional I2C bus, provides 64 × 8 bits of register storage, and is packaged in an 8-pin SOIC measuring 0.154 inch, or 3.90 mm, wide. A real-time clock is a semiconductor timing component that maintains calendar information independently of the host processor. In the system hierarchy, an RTC belongs to clock and timing integrated circuits, alongside oscillators, timers, and frequency-control devices. The DS1307 records seconds, minutes, hours, day, date, month, and year while also exposing 56 bytes of battery-backed storage for alarms, configuration, or application data. Principal verified features include serial I2C address and data transfer, a 64 × 8 register map, 56 bytes of nonvolatile SRAM, and automatic end-of-month adjustment for months with fewer than 31 days. The manufacturer describes it as a full BCD clock/calendar. The integrated SRAM distinguishes it from RTCs that provide only calendar registers, while the serial interface allows a host microcontroller or processor to read and update time without using many parallel pins. The device combines timekeeping and small amounts of persistent configuration storage in one compact IC. Its clock/calendar registers expose standard time information, while SRAM bytes can retain settings when the system loses its main supply, provided the RTC backup supply remains available. Exact electrical limits, oscillator accuracy, voltage range, current consumption, alarm behavior, and square-wave timing require confirmation from the complete manufacturer datasheet. Typical uses include industrial controllers, embedded data loggers, building equipment, access-control terminals, connected sensors, and legacy computer systems that retain an I2C host interface. A microcontroller reads the BCD calendar through the serial bus and can use the SRAM for small configuration records. Firmware must convert BCD values into binary or decimal and detect month rollover at the end of shorter months. Designers should confirm the backup-battery implementation, logic levels, address selection, pull-up arrangement, and decoupling against the manufacturer datasheet before layout release. The I2C bus requires suitable pull-ups, while the 8-SOIC footprint requires a land pattern matching the 3.90 mm-wide body. Do not infer oscillator accuracy or retention duration from the RTC category; those values must be verified for the selected production variant. This page consolidates the official DS1307 description, distributor package information, verified sourcing links, and engineering selection guidance. It also separates confirmed facts from parameters requiring verification, helping engineers evaluate the DS1307ZN+ without confusing a functionally similar RTC with a guaranteed pin-to-pin replacement.

RFQ پەیوەندی
DS1307ZN+T&R - I2C RTC with 56B SRAM | Analog Devices
DS1307ZN+T&R

DS1307ZN+T&R - I2C RTC with 56B SRAM | Analog Devices

The Analog Devices DS1307ZN+T&R is a low-power serial real-time clock and calendar with 56 bytes of nonvolatile SRAM, housed in an 8-pin SOIC package rated for a 5.5 V maximum supply. It maintains seconds, minutes, hours, day, date, month, and year information while communicating with a host through a bidirectional two-wire I2C bus. The DS1307ZN+T&R is supplied in tape-and-reel packaging for automated assembly. A real-time clock is a timekeeping integrated circuit that preserves calendar information when the main system is unpowered. The broader hierarchy is RTC -> serial clock/calendar -> timing IC -> semiconductor. Unlike a microcontroller software timer, the DS1307ZN+T&R continues tracking time independently, making it useful for data logging, industrial controllers, embedded products, and systems that require timestamps after reset or power interruption. The principal feature is the combination of BCD clock/calendar data and 56 bytes of NV SRAM in one compact device. The calendar automatically adjusts the end-of-month date for months with fewer than 31 days. The I2C interface reduces the number of host connections compared with a parallel real-time clock, while the 8-pin SOIC package supports conventional surface-mount manufacturing. The verified distributor description identifies the interface as 2-wire serial I2C and the memory as 56 bytes. The DS1307 uses a serial architecture in which address and calendar data are transferred over the same two-wire bus. Host firmware writes control and calendar registers or reads the current time, while the SRAM provides compact nonvolatile storage for alarms, counters, configuration data, or small log fragments. Its low-power design makes it appropriate for embedded systems in which the host is frequently powered down but wall-clock continuity remains valuable. Typical implementations include industrial data loggers, building-control equipment, consumer appliances, metering systems, and microcontroller-based embedded products. In each case, the RTC acts as the authoritative low-power time source while the host handles calculations, communications, user interaction, and higher-level control. The integrated SRAM can retain small configuration records without adding a separate external memory component. PCB design should preserve the exact 8-pin SOIC footprint and route the I2C lines as a properly terminated bus. The verified source set does not provide detailed pin names, crystal configuration, capacitor values, or electrical limits, so those design details must be confirmed in the current Analog Devices or Maxim Integrated manufacturer datasheet before layout and firmware are released. This page consolidates the verified manufacturer description, distributor records, package information, functional alternatives, and application guidance. It also distinguishes verified capabilities from parameters that still require datasheet confirmation, helping engineers evaluate the DS1307ZN+T&R without assuming unsupported electrical specifications.

RFQ پەیوەندی