بەرهەمەکان (970+)

BQ4847YMT RTC Module with CPU Supervisor | Texas Instruments
BQ4847YMT

BQ4847YMT RTC Module with CPU Supervisor | Texas Instruments

The Texas Instruments BQ4847YMT is a real-time clock module with a parallel clock/calendar interface, integrated 130 mAh battery, quartz crystal, CPU supervisor, watchdog timer, and battery-low warning features. Its 28-pin DIP module package measures 0.61 inches, or 15.49 mm, according to the distributor listing. The module counts seconds through years in BCD format and specifies clock accuracy of ±1 minute per month. A real-time clock, or RTC, is a clock-and-timing IC that maintains time independently of the system processor. It typically supplies calendar and alarm information, supports battery-backed operation during main-power loss, and allows embedded equipment to retain accurate timestamps after restart. The BQ4847YMT combines the RTC, clock source, backup battery, supervisor circuitry, and external-SRAM retention control in one module, reducing the number of separate timing and power components a board must accommodate. Key features include BCD time-of-day and calendar counting from seconds through years, an integrated battery and crystal, an on-chip battery-backup switchover circuit, nonvolatile control for an external SRAM, a 130 mAh battery capacity, and ±1 minute per month clock accuracy. The CPU-supervisor function helps system firmware distinguish normal operation from reset or power-failure events, while watchdog, interrupt, reset, and battery-low warning functions support reliable embedded-control behavior. The module uses a parallel interface rather than the serial bus found in many compact RTC packages. According to the verified distributor descriptions, it is packaged as a 28-DIP module and is categorized as a clock/calendar RTC IC. The integrated battery and crystal mean the associated crystal and primary backup-cell implementation details are contained within the module rather than requiring the same external arrangement as a conventional RTC IC. Typical uses include industrial controllers, data-acquisition equipment, embedded instruments, access-control systems, and legacy computer hardware requiring a parallel RTC interface. Designers should preserve the module's pinout and battery behavior, account for main-supply and backup-supply sequencing, and verify reset, watchdog, and SRAM-retention requirements against the application. The supplied verified data does not specify a full electrical limit table, operating-temperature range, or lead-time figures, so those details should be confirmed in the manufacturer documentation.

RFQ پەیوەندی
BQ4850YMA-85 - 512Kx8 NVSRAM RTC | Texas Instruments
BQ4850YMA-85

BQ4850YMA-85 - 512Kx8 NVSRAM RTC | Texas Instruments

The Texas Instruments BQ4850YMA-85 is a real-time clock module with 512Kx8 nonvolatile SRAM, a 4.5 V to 5.5 V supply range, parallel access, and a 32-DIP module package. The integrated subsystem combines timekeeping, battery-backed SRAM, a crystal, and power-fail control, making it suitable for systems that must retain time and configuration data across power interruptions. According to the supplied distributor data, it is packaged as a 0.610 inch, 15.49 mm 32-DIP module. A real-time clock module is a clock-and-timing IC that maintains calendar and time information independently of the host processor's main clock. This device provides RAM-like clock access, BCD time and calendar counting, and an interface intended to resemble an x8 SRAM. Its broader system position is timekeeping and data retention within embedded control, industrial instrumentation, and legacy computer equipment. The key verified characteristics are 512Kx8 NVSRAM organization, a 4.5 V to 5.5 V operating supply, a parallel interface, and integrated SRAM, RTC, crystal, power-fail control, and battery functions. The supplied search data also identifies unlimited write capability as a feature, although the detailed write-cycle limit, retention duration, and electrical timing values are not provided. The BQ4850YMA-85 uses BCD-formatted time information and a date format identified by the supplied search result as YY-MM-DD-dd, with time expressed as HH MM SS in 24-hour format. This organization can simplify firmware access, but the host software should still validate register maps, alarm behavior, and power-fail timing before production release. Typical uses include industrial controllers, data-acquisition equipment, embedded instruments, and legacy systems requiring a parallel RTC with nonvolatile data storage. The 32-DIP package favors through-hole assembly or socketed prototyping rather than compact surface-mount consumer products. Designers should verify the complete pinout and timing values from the manufacturer datasheet, preserve decoupling and battery backup behavior, and validate power-fail recovery before substitution. Because verified drop-in alternatives are scarce, functional alternatives must not be treated as pin-compatible without manufacturer confirmation. This page consolidates verified distributor information, sourcing links, application context, and design cautions that are not all available from a single manufacturer datasheet listing. It also distinguishes verified data from parameters that still require engineering confirmation.

RFQ پەیوەندی
BQ4850YMA-85N - 512Kx8 NVSRAM RTC | Texas Instruments
BQ4850YMA-85N

BQ4850YMA-85N - 512Kx8 NVSRAM RTC | Texas Instruments

The Texas Instruments BQ4850YMA-85N is a parallel-interface real-time clock and calendar module with an integrated 512Kx8 nonvolatile static RAM, crystal, power-fail control, and battery support in a 32-DIP module package. It operates from a 4.5 V to 5.5 V supply and records time in 24-hour HH MM SS format with a YY-MM-DD-dd date format. The device is supplied in a tube for production assembly. A real-time clock is a specialized integrated circuit that maintains time independently of the host processor. The BQ4850YMA-85N belongs to the RTC and calendar hierarchy, while its integrated RAM adds persistent data storage in the same module. This combination places it within clock-and-timing and data-retention applications where the system requires both accurate calendar information and nonvolatile storage without using separate timekeeping and memory devices. Key verified features include an integrated SRAM, real-time clock, crystal, power-fail control circuit, and battery support. The 512Kx8 NVSRAM provides 524,288 bits of storage, while the parallel interface gives the host direct access to time and memory registers. Operation from 4.5 V to 5.5 V suits conventional 5 V equipment, and the 32-DIP module format supports insertion into a through-hole board layout. The tube packaging option is intended for orderly manufacturing handling and automated or manual production insertion. Technically, the module combines timekeeping logic with nonvolatile static memory in one 32-pin package. Its BCD-based clock and calendar representation follows the verified HH MM SS and YY-MM-DD-dd formats. The integrated crystal establishes the timing reference, while the power-fail control and battery circuitry help preserve RTC operation and stored data during supply interruptions. Exact retention duration, battery characteristics, oscillator accuracy, and electrical limits beyond the supplied 4.5 V to 5.5 V supply range were not provided and therefore must be confirmed from the manufacturer datasheet before design release. Typical uses include industrial data loggers, instrumentation, embedded control systems, financial terminals, and equipment requiring a nonvolatile configuration or audit record. In such systems, the host processor can read the calendar through the parallel bus and use the NVSRAM for operating counters, calibration data, event logs, or configuration retention. Consolidation can reduce component count, but the complete host-bus timing, address map, battery chemistry, and write-protection behavior must be verified before schematic capture. The primary design consideration is to preserve the exact module footprint and verify every signal before substitution. A functional clock-and-RAM device is not automatically a drop-in replacement: supply limits, address mapping, access timing, battery handling, module dimensions, and power-fail behavior must all match. The verified sources did not establish five pin-compatible alternatives, so this page does not present unverified equivalents as drop-in parts. This product page combines verified manufacturer-related listings, distributor availability information, cross-reference results, package details, and engineering-specific cautions. It distinguishes confirmed BQ4850YMA-85N characteristics from parameters that still require the original manufacturer datasheet, providing a more reliable basis for sourcing and engineering review than a raw distributor listing alone.

RFQ پەیوەندی
BQ4852YMC-85 RTC with 512Kx8 NVSRAM | Texas Instruments
BQ4852YMC-85

BQ4852YMC-85 RTC with 512Kx8 NVSRAM | Texas Instruments

The Texas Instruments BQ4852YMC-85 is a real-time clock and nonvolatile SRAM module combining 512 Kbit of battery-backed SRAM, a clock/calendar, crystal control, and power-fail management in a 36-pin DIP module. The verified product listing identifies it as a parallel clock/calendar RTC in a 0.610 inch, 15.49 mm package. It also describes the device as pin-compatible with industry-standard x8 SRAMs, making it useful where an embedded system needs both persistent data and timekeeping without adding a separate memory device. A real-time clock (RTC) is a clock-and-timing IC that maintains calendar and time information while the main system is unpowered. A nonvolatile SRAM (NVSRAM) retains stored data across power loss, combining the persistence of memory with the timing functions of an RTC. Together, these devices provide backup storage, event timestamps, configuration retention, and elapsed-time measurement in industrial-control, instrumentation, data-acquisition, and embedded systems. The verified data identifies 512 Kbit organized as 512 Kbyte by 8 bits, real-time clock operation from seconds through years, RAM-like clock access, unlimited writes, and integrated SRAM, crystal, power-fail control, and battery functions. The BQ4852YMC-85 also includes watchdog-timer functionality according to the Mouser product description. Its 36-DIP module format supports through-hole assembly rather than a compact surface-mount design, making it especially relevant to legacy and industrial equipment with DIP-compatible footprints. The parallel interface permits direct connection between the RTC/NVSRAM and a host bus without the serial addressing required by I2C devices. The SRAM-like access method can simplify firmware when memory-mapped access is preferred. The power-fail control and backup-battery function help preserve data and maintain timekeeping during supply interruptions, although exact capacitor, battery, retention, and endurance values require confirmation in the manufacturer datasheet. Typical uses include industrial data loggers, test equipment, programmable controllers, meters, embedded instruments, and systems that require persistent configuration records alongside real-time timestamps. The package is not SOA data: it is a clock-and-timing and memory IC, not a discrete power semiconductor. The 16-page datasheet result supplied by the verified sources should be consulted for the complete pinout, electrical limits, battery configuration, oscillator characteristics, and power-fail behavior before design release. For a new design, verify the exact package dimensions, pin names, voltage levels, bus timing, and backup-power architecture against the manufacturer datasheet. For a replacement, do not rely on generic RTC or SRAM substitutes: the target requires a 36-DIP module, parallel access, 512 Kbyte by 8 organization, and compatible power-fail behavior. This page combines verified distributor metadata, structured product facts, and explicit data gaps rather than estimating unavailable electrical values.

RFQ پەیوەندی
CD4046AF/3 - 1.5MHz CMOS Phase-Locked Loop | Harris
CD4046AF/3

CD4046AF/3 - 1.5MHz CMOS Phase-Locked Loop | Harris

The Harris Corporation CD4046AF/3 is a CMOS phase-locked-loop, or PLL, integrated circuit with an operating frequency up to 1.5 MHz, supplied in a 16-CDIP ceramic dual-inline package with 0.300-inch, 7.62 mm lead spacing. The device combines a phase-locked-loop subsystem with dual phase comparators, supporting frequency synthesis, clock synchronization, tone generation, and signal-conditioning applications. A phase-locked loop is a feedback-control subsystem that compares a reference signal with an adjustable oscillator signal and drives the oscillator toward phase and frequency alignment. The PLL category belongs to the broader clock-and-timing hierarchy, where phase detectors, frequency dividers, voltage-controlled oscillators, and digital timing ICs work together to produce stable or programmable clock outputs. The CD4046AF/3 is identified as a low-power CMOS PLL with dual phase comparators. Its CMOS input and output structure suits low-power clock and control designs, while the 1.5 MHz upper operating frequency makes it appropriate for communication, instrumentation, modulation, and general-purpose frequency-processing circuits. The ceramic CDIP construction also supports use in applications where a through-hole package is preferred. The functional architecture allows an external voltage-controlled oscillator and timing components to be connected to the IC, enabling the loop to synthesize, divide, or lock onto a reference frequency. Dual phase-comparator choices support different detection arrangements and signal-polarity requirements. Users should account for comparator type, loop bandwidth, divider arrangement, and required pull-in range when designing the surrounding feedback network. Typical uses include FM and AM demodulation, frequency synthesis, tone decoding, clock recovery, phase-angle measurement, motor-speed control, and low-to-medium-frequency clock generation. The device can also serve as the central timing element in laboratory instruments and industrial control systems where a low-frequency reference must control an adjustable oscillator. For a new layout, place the timing, loop-filter, and oscillator components close to the associated pins and keep high-impedance comparator nodes compact to minimize pickup. Recheck operation across temperature and supply-voltage extremes, and verify the selected external components against the required lock range. Because detailed electrical limits and the complete pin description are not published on the product listing, consult the manufacturer datasheet before finalizing timing or loop-gain calculations. This product page consolidates the exact package information, PLL characteristics, sourcing links, comparison fields, and application guidance needed to evaluate the CD4046AF/3 for a new clock-and-timing design. It also distinguishes confirmed product characteristics from parameters that must be established from the full manufacturer datasheet.

RFQ پەیوەندی
CD4046AK - CMOS Micropower PLL | Harris | Clock & Timing
CD4046AK

CD4046AK - CMOS Micropower PLL | Harris | Clock & Timing

Harris Corporation CD4046AK is a CMOS micropower phase-locked-loop IC integrating a phase comparator, a high-gain voltage-controlled oscillator, a three-state VCO output stage, and a Schmitt-trigger input stage. The verified source identifies the device as a clock generator, PLL, and frequency synthesizer, but does not provide a verified numerical supply range, frequency range, package dimensions, pinout, or temperature grade. A phase-locked loop is a feedback-control circuit that synchronizes an output oscillator to a reference signal. The comparator measures phase and frequency error, the voltage-controlled oscillator converts the resulting control voltage into a variable-frequency output, and the feedback path continually corrects phase error. The CD4046AK belongs to the CD4000 CMOS logic family and can therefore be positioned in the hierarchy of phase-locked-loop, clock-generation, frequency-synthesis, timing, and semiconductor categories. Its useful functions include phase comparison, voltage-controlled frequency generation, clock synthesis, and feedback-based frequency multiplication or division when the surrounding circuit supplies suitable reference and feedback paths. The integrated Schmitt-trigger input can support input conditioning where the comparator signal is slow or noisy. Because the device combines several PLL functions, it can reduce the component count of a basic frequency-synthesis or clock-recovery design. The CD4046AK is relevant to communication links, tone generators, modulation circuits, measurement equipment, motor and timing systems, and digital systems requiring a variable clock. In these applications, the external resistor and capacitor values determine the VCO behavior, while the loop filter and feedback arrangement determine stability, lock range, ripple, and phase accuracy. Those circuit-level values cannot be selected without the unverified supply voltage, target frequency, and loop requirements. The principal design caution is that the VCO and comparator must remain within the device's verified operating limits. Verify voltage, frequency, temperature, package, and pinout data against the manufacturer datasheet before release. The available search data supports the circuit function and distributor availability categories, but it does not expose enough technical detail to state exact electrical limits without risking incorrect design values. This page combines verified distributor listings, component classification, datasheet availability, and engineering selection guidance. Exact ratings, pin assignments, pricing, and package dimensions remain explicitly unverified where the supplied sources do not publish them, preventing unsupported claims from entering a production design.

RFQ پەیوەندی
CD4046BCM - 1.6 MHz Micropower PLL | onsemi | Clock & Timing
CD4046BCM

CD4046BCM - 1.6 MHz Micropower PLL | onsemi | Clock & Timing

onsemi CD4046BCM is a micropower phase-locked loop (PLL) integrated circuit with an operating frequency of up to 1.6 MHz, packaged in a 16-pin SOIC measuring 0.154 inch, or 3.90 mm, in width. The device combines a low-power linear voltage-controlled oscillator (VCO), a source follower, a zener diode, and two phase comparators in one package. These functions allow a single IC to compare an input signal with a feedback signal, generate a controllable periodic output, and lock the feedback frequency and phase to a reference. A phase-locked loop is a feedback-control system that belongs to the clock and timing IC hierarchy. The comparator measures phase or frequency error between two signals, while the VCO produces an output whose frequency can be adjusted by a control voltage. When the feedback and reference signals agree, the loop reduces the error and maintains a stable relationship between them. This makes PLDs useful when a circuit must generate, divide, demodulate, track, or synchronize a timing signal. The CD4046BCM is identified specifically as a micropower PLL and is a 1.6 MHz part. Its internal VCO, source follower, zener diode, and dual phase-comparator arrangement provide the principal functional blocks needed for closed-loop timing control. The source follower can provide a buffered control path for the VCO, while the zener provides a stable voltage reference within the IC. External resistors and capacitors determine the VCO frequency range and establish the loop dynamics. The 16-pin SOIC package provides a surface-mount implementation for applications requiring a compact phase-locking subsystem. Its external frequency-setting and loop-filter components allow the operating range to be adapted to a reference frequency and required capture bandwidth. Designers should also account for comparator propagation delay, VCO gain, component tolerance, and startup behavior when setting loop bandwidth; these values should be confirmed from the manufacturer datasheet before finalizing timing margins. Typical uses include frequency synthesis, frequency multiplication and division, tone generation, FM or phase demodulation, clock recovery, and synchronization of a local oscillator to an external reference. In a receive chain, the PLL can compare an incoming signal with an internally generated feedback signal and correct its VCO until the two agree. In a transmit chain, it can produce a stable carrier whose phase is controlled relative to a reference. The principal design consideration is loop stability. The phase-comparator type, VCO gain, limiting resistors, loop filter, and input frequency range must be selected together; excessive loop gain can produce ringing or oscillation, while insufficient gain can increase phase error. Keep the VCO timing components close to the device, maintain a clean return path, and compare the timing margin against temperature and supply-voltage changes. This product page combines the exact device identity, package information, functional block description, structured specifications, practical application guidance, and qualified replacement considerations. It is intended to help engineers determine whether the CD4046BCM fits a timing-control design before committing the 16-pin SOIC footprint to a PCB.

RFQ پەیوەندی
CD4046BCN - 1.6MHz Micropower Phase-Locked Loop | onsemi
CD4046BCN

CD4046BCN - 1.6MHz Micropower Phase-Locked Loop | onsemi

The onsemi CD4046BCN is a micropower phase-locked loop (PLL) integrated circuit with a maximum stated operating frequency of 1.6 MHz, supplied in a 16-pin dual in-line package measuring 0.300 inches, or 7.62 mm, in pin pitch. The device combines a low-power linear voltage-controlled oscillator with a source follower, a zener diode, and two phase comparators in one package. A phase-locked loop is a feedback-control circuit that compares an input signal with a reference signal and adjusts a controllable oscillator until their phase relationship is locked. The CD4046BCN belongs to the PLL and clock-generation hierarchy: its internal VCO provides the adjustable timing element, while its phase comparators produce error information for the feedback loop. The source follower and zener diode support signal conditioning and voltage-reference functions within the PLL architecture. The principal characteristics include micropower operation, a linear voltage-controlled oscillator, two phase-comparator sections, and a 1.6 MHz upper frequency stated for the CD4046BCN. The common comparator and signal inputs allow each phase comparator to be evaluated against the same reference and input nodes. This integration is useful when a circuit requires adjustable frequency generation and closed-loop phase synchronization without implementing those functions from discrete blocks. Technically, the CD4046BCN is designed around CMOS-compatible phase-locked-loop functions. Its VCO can be controlled by an external voltage, while the phase-comparator outputs support implementation of a closed feedback loop. The two comparator arrangements can be selected according to the required input signal level and phase-detection behavior. Because exact voltage limits, timing characteristics, and output-drive details are defined by the manufacturer datasheet, those values should be confirmed against the operating conditions of the final design. Typical applications include FM and AM signal generation, frequency synthesis, tone generation, frequency multiplication, frequency division, and phase-locked frequency multiplication. The PLL can also be used in communication equipment, modulation circuits, timing systems, measurement instruments, and control systems where a stable adjustable frequency is required. The 16-pin through-hole DIP package is particularly convenient for prototyping, laboratory instruments, and legacy industrial equipment. When designing with the CD4046BCN, follow the manufacturer pin-description table when assigning signals and place the loop-filter components close to their associated pins. Verify the VCO control-voltage range, required external components, and maximum operating frequency against the final frequency plan. Use the manufacturer datasheet as the controlling reference for supply voltage, input coupling, output behavior, and operating-temperature limits. This product page combines the verified device description with application guidance, packaging information, and engineering-oriented selection context. It helps engineers identify where the micropower PLL belongs in a clock-generation or modulation design while directing detailed electrical validation to the manufacturer datasheet.

RFQ پەیوەندی
CD4046BE - 2.4MHz Micropower CMOS PLL IC | Texas Instruments
CD4046BE

CD4046BE - 2.4MHz Micropower CMOS PLL IC | Texas Instruments

The Texas Instruments CD4046BE is a 2.4 MHz CMOS micropower phase-locked-loop (PLL) IC packaged in a 16-pin dual in-line plastic package. It operates from 3 V to 18 V and integrates a low-power linear voltage-controlled oscillator (VCO), two phase comparators, a common signal-input amplifier, and a common comparator input. These headline values place it in the clock-and-timing and frequency-synthesis hierarchy while supporting low-power voltage-controlled frequency generation, phase comparison, and feedback-based synchronization. A phase-locked loop is a feedback-control system in which a voltage-controlled oscillator is adjusted until a generated signal matches the phase relationship of a reference input. Within the CD4046B family, the low-power linear VCO and alternative phase-comparator outputs allow different loop architectures to be selected. The CD4046BE therefore combines oscillator and detector functions that would otherwise require separate discrete blocks, reducing component count in clock multiplication, demodulation, frequency synthesis, tone generation, and signal-conditioning circuits. The verified source identifies the CD4046BE as a CMOS micropower PLL with a 2.4 MHz maximum operating frequency, a 3 V to 18 V supply range, and approximately 10 mA supply current in the comparison data. It is offered in a 16-DIP package with a 0.300-inch pin pitch and 7.62 mm lead spacing. The two internal phase comparators and shared input amplifier provide implementation flexibility, but loop stability still depends on correct external resistor, capacitor, filtering, and feedback selections. Architecturally, the chip separates signal generation from phase detection. The linear VCO responds to its control voltage, while the phase-comparator sections generate correction information for the feedback loop. Comparator I is suited to positive-edge locking, whereas Comparator II supports zero-degree or 180-degree phase comparison depending on its configuration. Designers must follow the manufacturer datasheet for exact comparator logic, output states, operating limits, and timing because those details were not fully present in the supplied source text. Typical uses include FM and FM-to-AM demodulation, frequency synthesis, tone decoding, frequency multiplication, scanning or sweep generation, and low-frequency clock generation. The part is particularly relevant when variable frequency or phase correction is required and a conventional fixed-frequency oscillator is insufficient. Its CMOS micropower architecture favors low-power signal-path and control applications, provided the external loop network is designed for the intended frequency and supply voltage. The most important design consideration is loop-component validation. Keep the VCO timing network and feedback-path components close to the device, use the datasheet's recommended topology, and verify acquisition range, lock range, ripple, and phase error on the intended prototype. Component tolerances and parasitic capacitance can materially affect behavior at higher frequencies. Because the verified material does not provide complete timing or pin-function tables, engineers should obtain the manufacturer datasheet before release to production. This page combines distributor availability, verified family-level specifications, sourcing information, replacement constraints, and practical PLL design guidance. It distinguishes confirmed data from missing parameters while preserving the key advantage of CD4046BE: an integrated CMOS PLL and VCO in a standard 16-pin DIP package.

RFQ پەیوەندی
CD4046BF - CMOS Micropower Phase-Locked Loop | Texas Instruments
CD4046BF

CD4046BF - CMOS Micropower Phase-Locked Loop | Texas Instruments

The Texas Instruments CD4046BF is a CMOS micropower phase-locked-loop integrated circuit operating from 3 V to 18 V in a 16-lead CDIP package rated for -55 C to +125 C. It integrates a low-power linear voltage-controlled oscillator, two phase comparators, a common signal-input amplifier, and a common comparator input. The device is designed for frequency synthesis, modulation, demodulation, tone decoding, and frequency-related control systems. Its CMOS construction supports low-power operation, while the two comparator options allow selection between phase-comparator modes suited to different locking behavior. The 16-CDIP mechanical package provides through-hole mounting and is suitable for industrial, instrumentation, communications, and legacy control systems requiring a stable, qualified temperature range. The CD4046BF designation identifies the 16-lead ceramic dual-in-line package variant within the CD4046B family. A phase-locked loop is a feedback-control system in which an internal voltage-controlled oscillator is adjusted until its output frequency or phase agrees with a reference input. In the CD4046BF, the signal-input amplifier feeds the selected phase-comparator path, while the VCO provides the tunable output. The PLL can therefore compare an incoming reference against a divided or generated frequency and present an error voltage for loop filtering and frequency control. The loop filter is external, allowing designers to tune loop bandwidth, capture behavior, damping, and output jitter according to the application. The key features of the CD4046BF are its 3 V to 18 V supply range, micropower CMOS operation, integrated VCO, two phase comparators, and broad -55 C to +125 C temperature rating. The VCO is linear, making the output frequency controllable by an external voltage. The common input amplifier and comparator input simplify use with external frequency-divider and loop-filter networks. The CD4046BF is a useful building block when a system needs both frequency synthesis and flexible feedback-loop implementation rather than a fixed-frequency oscillator. The device uses analog control techniques around a CMOS digital-compatible integrated circuit. The VCO output frequency depends on its control voltage and external timing components, while the phase comparator converts phase or frequency differences into an error signal. Designers should account for comparator type, loop-filter transfer function, VCO gain, divider ratio, reference frequency, and component tolerances. In practical designs, a low-pass filter commonly connects the comparator output to the VCO control input, and a frequency divider may be inserted between the VCO output and comparator input when integer multiplication is required. Typical applications include FM and AM demodulation, tone decoding, frequency synthesis, frequency multiplication, frequency division, phase discrimination, motor-speed-related modulation, communications interfaces, and instrumentation. The 16-CDIP package is particularly useful where through-hole assembly, rugged mechanical construction, or a wide temperature range is preferred over a surface-mount footprint. Designers should confirm timing, output-drive, supply-current, and component-temperature requirements against the manufacturer datasheet before production release. The most important design consideration is selecting the correct comparator and calculating the loop filter around the intended reference frequency. A filter that is too aggressive can increase noise or slow acquisition, while an insufficiently filtered loop can jitter or oscillate. Keep the VCO timing components and sensitive comparator nodes away from noisy switching paths, use a stable low-noise control voltage, and check the maximum operating frequency for the selected external components. The CD4046BF is not a power semiconductor, so a safe operating area specification is not applicable.

RFQ پەیوەندی
CD4046BK - 2.4MHz PLL Clock Synthesizer | Harris
CD4046BK

CD4046BK - 2.4MHz PLL Clock Synthesizer | Harris

The Harris CD4046BK is a phase-locked-loop clock synthesizer and frequency multiplier IC operating up to 2.4 MHz, supplied in a 16-pin flat-pack package. The verified distributor listing identifies the device as a phase lock loop IC with one output stage and a 16-pin CFP package. Its key function is to compare an input reference signal with a feedback signal and generate a stable, phase-related output suitable for clock generation, frequency synthesis, modulation, and signal-processing systems. A phase-locked loop is a feedback-control system that locks the frequency and phase of an output oscillator to an external reference. The CD4046BK belongs to the clock and timing IC hierarchy, combining a phase comparator, voltage-controlled oscillator, and auxiliary output circuitry. This makes it useful when a circuit needs programmable or reference-synchronized timing rather than a free-running oscillator. The verified data specifically confirms a maximum operating frequency of 2.4 MHz and a 16-CFlatPack package. Other operating details, electrical limits, pin names, temperature grades, supply voltage, and current consumption were not supplied in the verified records and therefore must be confirmed from the manufacturer datasheet before design release. The listed Harris and Intersil source records also indicate historical manufacturer-source variation, so procurement should verify the exact manufacturer, package marking, and datasheet revision. Typical design uses include low-frequency clock generation, frequency multiplication, tone generation, frequency-to-voltage conversion, phase-locked modulation, and instrumentation where a feedback loop maintains a controlled output. The loop filter, reference oscillator, and feedback divider are external circuit elements, allowing the system designer to set loop bandwidth and dynamic behavior. Actual performance depends on component tolerances, loop filter design, supply voltage, and the complete application circuit. For new designs, use the exact package footprint and pinout from the relevant CD4046BK datasheet rather than assuming that all CD4046 variants are interchangeable. Confirm supply-voltage limits, VCO gain, phase-comparator characteristics, output drive, and timing guarantees before substituting any part. The verified records identify distributor availability and pricing sources but do not provide a complete standardized pricing ladder or authoritative lifecycle statement. This product data synthesizes the verified distributor descriptions, package information, pricing reference, and cross-reference-search results. It distinguishes documented facts from missing technical parameters and does not infer unverified electrical specifications, lifecycle status, or manufacturer qualification claims.

RFQ پەیوەندی
CD4046BPW - 2.4MHz CMOS Micropower PLL | Texas Instruments
CD4046BPW

CD4046BPW - 2.4MHz CMOS Micropower PLL | Texas Instruments

Texas Instruments CD4046BPW is a CMOS micropower phase-locked-loop integrated circuit rated for operation up to 2.4 MHz and housed in a 16-pin TSSOP package. It integrates a low-power linear voltage-controlled oscillator, two phase comparators, a common signal-input amplifier, and a common comparator input. The architecture also includes a 5.2 V Zener diode for optional supply-voltage regulation. A phase-locked loop, or PLL, is a feedback-control system in which an internal oscillator is tuned until its phase and frequency match a reference input. The CD4046B family belongs to the broader clock and timing hierarchy: phase-locked loop -> frequency synthesis and control -> clock and timing integrated circuit -> semiconductor. Its combination of a VCO and phase-detection functions allows one device to perform synchronization, frequency multiplication, frequency division, demodulation, and frequency comparison functions. The principal functional blocks support two phase-comparison methods. The circuit can operate with a phase comparator for applications requiring zero or 180-degree phase relationships, or with a frequency comparator for lock-range and frequency-synthesis work. The VCO provides the controllable oscillation source, while the comparator and amplifier paths sense the relationship between the external reference and internal oscillator signals. An externally supplied control voltage can therefore determine the oscillator operating point within the device's operating limits. The micropower CMOS implementation is suited to low-power control and signal-processing systems where the operating supply must remain low and circuit area is constrained. The 16-TSSOP package provides a surface-mount option for compact industrial, instrumentation, communications, and control equipment. The 2.4 MHz frequency designation identifies the upper operating capability highlighted for this ordering variant and should be checked against the specific VCO configuration, supply voltage, and timing conditions used in the target design. Typical uses include frequency synthesis, clock recovery, tone generation, tracking loops, FM or phase-sensitive demodulation, frequency multiplication and division, and general closed-loop frequency-control systems. In these applications, the reference signal enters the comparator path while the VCO produces the adjustable internal signal. Loop filtering and output routing then determine whether the application behaves as a multiplier, divider, synchronizer, or demodulator. Design should begin with the manufacturer's phase-comparator and VCO application guidance. Verify the selected comparator mode, feedback topology, VCO free-running frequency, supply range, and external component values before layout. Keep the timing network and loop-filter components close to their associated pins, maintain a stable ground reference, and route the oscillator and feedback paths away from noisy switching nodes to reduce unintended coupling. This product page combines the package and frequency information, functional architecture, alternative-device analysis, comparison parameters, and practical design guidance in one engineering-focused reference. It also distinguishes package-compatible choices from parts that require a different footprint, helping designers avoid treating a functionally similar PLL as a true PCB drop-in replacement.

RFQ پەیوەندی
CD4059AE - Programmable Divide-by-N Counter | Texas Instruments
CD4059AE

CD4059AE - Programmable Divide-by-N Counter | Texas Instruments

Texas Instruments CD4059AE is a CMOS programmable divide-by-N counter with a 16-bit jam-programmable count value from 3 to 15,999, housed in a 24-lead dual-in-line plastic package. It counts positive clock edges and produces a fixed-width output pulse at a rate equal to the input frequency divided by the programmed value N. The output provides TTL-compatible drive capability. A programmable divide-by-N counter is a clock-and-timing logic device that divides an input pulse train by a selectable integer. It belongs to the counter hierarchy, which includes frequency dividers and timing counters, and ultimately falls within digital logic ICs and clock-and-timing semiconductor categories. This architecture makes the CD4059AE useful whenever a stable reference frequency must be reduced to a lower derived frequency without changing the original signal source. The 16 jam inputs establish the divide ratio, allowing division by any number from 3 through 15,999. A divide-by-16 counter is therefore the conventional implementation, while the wider jam-input arrangement supports programmable ratios without adding a separate binary counter. The single output pulse is one clock cycle wide, making its relationship to the input timing straightforward to analyze and measure. The CD4059AE uses positive-edge counting, so the active transition is the rising edge of the clock waveform. Designers must account for setup and hold requirements around the jam inputs because changing the programmed divide value while the counter is operating can produce a transient output disturbance. The wide programmable range supports synthesized timing, pulse-rate division, periodic event generation, and frequency scaling. Typical applications include digital timer and counter modules, industrial pulse-generation circuits, clock dividers in control equipment, and repetitive event-rate reduction in test systems. The fixed-width output can trigger downstream counters or timing stages, while the jam inputs allow the system to change its operating rate under supervisory control. For dependable operation, use the manufacturer's pin-description table when assigning PCB signals and verify every jam-input state required by the desired division ratio. Confirm clock edge timing and output loading against the device limits, then provide suitable bypassing and a clean common ground reference. This page combines programming guidance, practical circuit considerations, and packaging information to support faster design review and sourcing. The CD4059AE remains a useful choice when a 24-lead through-hole programmable divider is preferred over a smaller logic device, particularly when the design benefits from direct jam programming across the full 3-to-15,999 ratio. Its 24-pin footprint requires adequate board spacing, so compact modern equipment may require a different counter architecture rather than a forced package substitution.

RFQ پەیوەندی
CD4518BE - Dual BCD Up-Counter, 8 MHz | Texas Instruments
CD4518BE

CD4518BE - Dual BCD Up-Counter, 8 MHz | Texas Instruments

The Texas Instruments CD4518BE is a dual four-bit BCD up-counter built with CMOS logic, supporting operation from 3 V to 18 V and clock frequencies up to 8 MHz in a 16-pin PDIP package. The device contains two internally synchronous four-stage counters that can count upward in binary-coded decimal, or BCD, format and may be operated with positive or negative clock transitions. A BCD counter is a digital counter whose four-bit output represents decimal digits from zero through nine. The CD4518 family combines two such counters in one package, allowing a design to maintain two independent count sequences without using two separate counter packages. Within the logic-component hierarchy, it is a CMOS counter IC, a member of the CD4000 logic series and a larger category of clock, timing, and state-sequencing semiconductors. Key features include two four-bit counting sections, internally synchronous four-stage counting, positive or negative clock-edge operation, and a maximum clock frequency of 8 MHz. Its 3 V to 18 V supply range permits use in conventional 5 V and 9 V logic systems as well as higher-voltage CMOS designs. The PDIP-16 package is suitable for through-hole assembly, prototyping, legacy industrial equipment, and educational or maintenance applications. Each counter section includes a clock input, a data-enable function, and four decade outputs. The device can be configured for cascading or extended counting when a larger number of decimal positions is required. Because each section uses synchronous internal stages, the output transitions occur on clock edges, allowing the counter to be used in frequency division, event sequencing, decade generation, and general digital timing systems. Typical applications include decade timing counters, pulse-counting panels, industrial sequence controllers, laboratory test fixtures, digital clocks, programmable counters, and embedded control logic that must represent decimal values directly. The two-counter architecture is particularly useful when a system requires two related count values, such as minutes and seconds, units and tens, or two independent event totals. Designers should use the manufacturer pin-description table when assigning PCB signals and should account for CMOS input behavior, unused outputs, reset release timing, and clock-edge polarity. This page combines the manufacturer product information, verified distributor listings, cross-reference findings, package details, and practical selection guidance for engineers evaluating the CD4518BE.

RFQ پەیوەندی
CD4521BPW - 24-Bit CMOS Frequency Divider | Texas Instruments
CD4521BPW

CD4521BPW - 24-Bit CMOS Frequency Divider | Texas Instruments

The Texas Instruments CD4521BPW is a CMOS 24-stage frequency divider with one 24-bit counter element, negative-edge triggering, and a maximum count rate of 13 MHz. It operates from 3 V to 18 V and is packaged in a 16-pin thin shrink small-outline package (TSSOP, PW). The divider divides the input clock frequency by two at each of its 24 stages, supporting accurate frequency division for timing and clock-generation circuits. A frequency divider is a clock-and-timing logic IC that converts an input clock into a lower-frequency output by counting clock cycles. The CD4521B belongs to the broader CMOS logic family and is designed for dependable operation across a broad supply range. Its staged divide-by-two architecture makes it useful when a circuit requires a stable divided clock while retaining a straightforward serial counter implementation. The principal device characteristics include a 3 V to 18 V supply range, a 13 MHz count rate, one counter element, and a 24-bit counting capacity. According to the Texas Instruments CD4521B datasheet, the device is tested for 20 V quiescent current and includes 5 V, 10 V, and 15 V parametric ratings. Its standardized symmetrical output characteristics support predictable interfacing with other CMOS logic. The CD4521B is designed in accordance with JEDEC Standard No. 13B, “Standard Specifications for Description of ‘B’ Series CMOS Devices.” The CD4521BPW ordering option uses the 16-lead PW thin shrink small-outline package and is rated for operation from -55 °C to 125 °C. This combination of wide supply range, extended temperature capability, and division depth makes the device applicable beyond conventional laboratory and consumer clock circuits. Typical uses include divide-by-two clock generation, instrumentation timing, digital frequency measurement, pulse-rate processing, and embedded systems that need a lower-frequency clock derived from a stable oscillator. In a two-terminal oscillator arrangement, the input clock can drive the counter while the final-stage output provides a divided waveform. Designers should observe the required reset behavior and ensure that timing margins remain adequate at the selected supply voltage and clock rate. For PCB implementation, keep the clock path short and place any required bypass capacitors close to the supply and ground pins. Because the package has 16 leads, land-pattern and fanout errors can prevent reliable assembly. Review the Texas Instruments pin-description table and package drawing before assigning signal names or routing the board. This product page combines the Texas Instruments datasheet specifications, exact ordering information, drop-in replacement assessment, package guidance, and application-oriented engineering notes to support faster component selection and board-design verification.

RFQ پەیوەندی
CD4536BD - Programmable 24-Bit Timer | Texas Instruments
CD4536BD

CD4536BD - Programmable 24-Bit Timer | Texas Instruments

The Texas Instruments CD4536BD is a programmable timer and ripple-counter CMOS integrated circuit in a 16-pin SOIC package. It contains 24 ripple-binary counter stages, can count from 1 to 2^24 clock edges, and allows the first eight stages to be bypassed so a 4-bit selection code can access an output from any of the remaining 16 stages. The device can operate from an external clock or an RC oscillator built around its on-chip oscillator components. A programmable timer is a timing IC that divides an input frequency into selectable time intervals. The CD4536B belongs to the CMOS counter family within the broader timer and clock-and-timing hierarchy. Its configurable counter length, selectable output stage, and external-clock capability make it useful for periodic-event generation, frequency division, time-delay generation, and industrial control logic without requiring a microcontroller. The principal feature of the CD4536B is its flexible counter architecture. Each of 16 selectable output taps can provide a different division ratio, while the first eight stages can be bypassed to reduce the counting interval. Its outputs have standardized, symmetrical characteristics, and its quiescent current is tested at 20 V across the 5 V, 10 V, and 15 V parametric ratings. The family is designed to meet the stated JEDEC Tentative Standard No. 13B requirements for B-series CMOS devices. The CD4536BD combines digital counting with analog RC timing functions. An external clock can be applied when precise system-synchronized timing is required, while the internal oscillator permits stand-alone interval generation with external resistor and capacitor values. The selectable output stages let one oscillator or clock source serve several timing tasks, reducing the number of separate timers required in a control design. Typical uses include industrial pulse and delay generation, repetitive process-control timers, frequency dividers, low-frequency clock generation, programmable pulse trains, and embedded automation systems. The device is also useful in laboratory and test equipment where a selectable division ratio or independently adjustable RC time constant is needed. It can also complement CMOS divider and oscillator products in broader sequential-control systems. When designing around the CD4536BD, calculate the RC oscillator timing from the manufacturer datasheet's timing equations and component tolerances rather than treating the nominal frequency as exact. Keep external clock edges within the specified input limits, connect unused inputs to defined logic levels, and place decoupling capacitors close to the supply pins. Verify output rise and fall times when driving long traces or high-capacitance loads. This product page combines the functional architecture of the CD4536B with practical timing guidance, package information, comparison criteria, and focused design notes. It supports faster part selection by distinguishing timer operation from general-purpose counters and highlighting the design checks that matter most for reliable CMOS timing circuits.

RFQ پەیوەندی
CD4536BD3 - 24-Stage CMOS Programmable Timer | Texas Instruments
CD4536BD3

CD4536BD3 - 24-Stage CMOS Programmable Timer | Texas Instruments

Texas Instruments CD4536BD3 is a CMOS programmable timer built around 24 ripple-binary counter stages, with selectable output access to 16 counter stages and operation from an external clock or on-chip RC oscillator. The device supports clock frequencies up to 5 MHz and is available in the 16-pin SOIC package identified by suffix D3. Its architecture combines a long binary count, programmable output selection, and timer functions in one timing IC. A programmable timer is an integrated timing component that counts clock edges or free-running oscillator cycles and produces an output after a selected count. The CD4536B family belongs to the CMOS logic and clock-and-timing hierarchy: programmable timer → counter → clock and timing IC → integrated circuit. This makes it useful when a design needs adjustable delays, periodic events, long timing intervals, or multiple selectable time constants without a microcontroller. The principal feature is a 24-stage ripple-binary counter that can count from 1 to 2^24. The first eight stages may be bypassed, allowing the 4-bit A, B, C, and D selection inputs to address one of 16 outputs from the remaining stages. This programmable selection shortens the effective count range compared with using all 24 stages and gives designers a practical way to set different delay or period values in one circuit. The CD4536B can operate from an external clock or from an RC timing network connected to the on-chip oscillator. According to the Texas Instruments CD4536B datasheet, the monostable input can be disabled by connecting MONO IN to ground through a resistor of 10 kΩ or higher. The device therefore supports both continuously running oscillator applications and triggered monostable timing functions, subject to the detailed connection and trigger requirements in the datasheet. Typical uses include industrial pulse and delay generation, periodic control timers, laboratory timing modules, counters, automotive-style repetitive control logic, and embedded control subsystems where a dedicated timer is preferable to software timing. The selectable counter outputs are especially useful when one timer must support several operating rates or when the required interval changes with a configuration input. When laying out a CD4536BD3 circuit, keep the oscillator and timing components close to the associated device pins, maintain the required bypass-network connections, and account for CMOS input leakage and temperature effects when selecting external resistors or capacitors. Validate pulse width and count accuracy over the full intended supply-voltage and temperature range rather than relying only on nominal RC values. This product record combines the verified device identity, package and timing architecture with practical implementation guidance. It also organizes same-family drop-in alternatives and distinguishes which electrical details require confirmation against the manufacturer datasheet before production release.

RFQ پەیوەندی
CD4536BDW - 24-Stage CMOS Programmable Timer | Texas Instruments
CD4536BDW

CD4536BDW - 24-Stage CMOS Programmable Timer | Texas Instruments

Texas Instruments CD4536BDW is a CMOS programmable timer and ripple-binary counter built around 24 counter stages, with an operating clock listed up to 5 MHz and a 16-pin SOIC package. The device can count from 1 to 2^24, and its first eight stages can be bypassed so a four-bit selection code chooses an output from the remaining 16 stages. It accepts an external clock or can operate as an RC oscillator using its on-chip oscillator components. A programmable timer is a timing and counting semiconductor that converts elapsed time or external clock pulses into selectable digital outputs. The CD4536 belongs to the CMOS timer and counter hierarchy, combining a monostable oscillator, a ripple-binary counter, a stage-bypass function, and a four-output decoder in one integrated circuit. This integration allows a single package to replace separate oscillator, counter, and output-selection circuitry in periodic or one-shot timing systems. The manufacturer describes 24 ripple-binary stages, a selectable output from any of 16 stages after bypassing the first eight, and operation from an external clock or an RC oscillator. Four selector inputs labeled A, B, C, and D provide the output-stage code. A logic high at the 8-BYPASS input bypasses the first eight stages, while the timer also includes a monostable input and an external reset function. Its CMOS implementation and symmetric output characteristics suit low-power digital control and timing designs. The timer architecture supports both continuous counting and one-shot operation. The monostable input receives the triggering event, and grounding it through a resistor of 10 kΩ or higher disables the one-shot function as described by the manufacturer. When an external clock is used, the counter advances on clock transitions, while the four decoded outputs provide multiple timing taps that can reduce the need for external decoding logic. Typical applications include industrial pulse and interval timing, delayed-event sequencing, periodic process control, laboratory pulse generators, and embedded control systems that need several related time bases. The four selectable outputs are particularly useful when one timer must provide multiple coordinated intervals instead of requiring four separate counters. An external oscillator or clock source can also establish the operating frequency for the timing system. When designing the circuit, verify the reset polarity, oscillator component values, and selected output timing in the CD4536B datasheet. Keep bypass and selector inputs away from noisy switching nodes, use a clean clock source when timing accuracy matters, and account for supply-voltage variation. Decoupling near the supply pins and controlled input rise times are especially important when the timer is used as a long-duration counter in electrically noisy equipment. This page combines the manufacturer's timer architecture and ordering information with practical oscillator, bypass, output-selection, and PCB guidance. It also organizes compatible CD4536B family ordering codes and distinguishes verified device characteristics from specification fields that require engineering confirmation.

RFQ پەیوەندی
CD4536BE - 5 MHz CMOS Programmable Timer | Texas Instruments
CD4536BE

CD4536BE - 5 MHz CMOS Programmable Timer | Texas Instruments

The Texas Instruments CD4536BE is a CMOS programmable timer IC with a maximum frequency of 5 MHz, supplied in a 16-pin PDIP package. It combines timer, oscillator, and counter functions in one device, allowing a fixed resistor-capacitor network or external clock to control timing and frequency behavior. According to the distributor listing, its operating temperature range is -55°C to 125°C. A programmable timer is a type of clock and timing IC used to generate, delay, divide, or count time-related signals. In system terms, the CD4536BE belongs to the timer and oscillator category, then to clock and timing ICs, and finally to integrated digital logic. Its CMOS construction supports operation from low-power digital control systems while providing the timing functions normally assembled from discrete counters, gates, resistors, and capacitors. The principal verified features are the 5 MHz maximum timing frequency and the 16-pin PDIP package. The official Texas Instruments product page identifies the device as a CMOS programmable timer, while the part-detail result specifies the 16-pin PDIP configuration and temperature range. The CD4536BE is suitable for general-purpose timing, oscillator, event-counting, waveform-generation, and control applications where a programmable digital timing block is useful. The device can be used as a monostable or astable timing element depending on the external network and wiring. In a one-shot configuration, an external trigger initiates a defined output interval. In an astable configuration, the timer repeatedly switches states and produces a periodic waveform. Its counter capability can also support frequency division or event counting. Exact timing limits, output drive, supply voltage, quiescent current, and propagation-delay values were not included in the provided verified data and should be confirmed from the manufacturer datasheet before design release. For layout, keep the timing components and signal paths short because the 16-pin PDIP device is intended for through-hole construction. Follow the manufacturer pinout and application examples exactly. Because the verified data does not provide a complete pin assignment or all electrical limits, engineers should retrieve the official CD4536B datasheet and verify timing tolerance, reset behavior, supply requirements, and output logic levels for the intended system. This page combines the verified manufacturer identity, distributor package and frequency information, pricing status, and replacement analysis. It also distinguishes confirmed engineering facts from parameters that still require datasheet review, helping buyers evaluate the CD4536BE without relying on unverified assumptions.

RFQ پەیوەندی
CD4536BK - CMOS Programmable Timer | Texas Instruments
CD4536BK

CD4536BK - CMOS Programmable Timer | Texas Instruments

The Texas Instruments CD4536BK is a CMOS programmable timer with 24 ripple-binary counter stages, selectable output timing, and operation from an external clock or an RC oscillator. It supports count sequences from 1 to 2^24, allows the first eight stages to be bypassed, and provides a 4-bit selection code for one of the remaining 16 output stages. The device is identified in a 16-lead CDFP package. A programmable timer is a clock-and-timing IC that combines an internal binary counter with oscillator and output-selection circuitry. Within the broader hierarchy of timer IC, digital logic IC, clock and timing IC, and semiconductor categories, it provides a flexible way to divide an input frequency or generate a selectable time interval. Instead of requiring a fixed counter size, the CD4536B family can bypass eight stages and select among 16 remaining tap positions. Key features include standardized symmetrical output characteristics, 24 ripple-binary counting stages, external-clock capability, and an on-chip RC-oscillator arrangement. The manufacturer also tests quiescent current at 20 V and specifies parametric ratings at 5 V, 10 V, and 15 V. These characteristics make the timer useful when an adjustable time base is more valuable than a fixed-frequency divider. Technically, the CD4536B operates as a ripple-binary counter with programmable output selection. Its first eight stages may be bypassed, leaving 16 stages that can be addressed by a 4-bit code. An external clock can drive the counter directly, while resistor-capacitor timing components can establish an on-chip RC oscillation. This architecture supports one-shot, repetitive timing, delayed-event, clock-divider, and programmable-delay implementations without requiring a microcontroller for basic timing tasks. Typical applications include industrial pulse and delay generation, laboratory pulse generators, timer modules, event sequencing, periodic control loops, and low-speed clock division. The device is particularly suitable where a fixed CMOS logic implementation is preferable to firmware-based timing, provided the design accounts for oscillator tolerance and propagation-delay variation. Designers should treat the CD4536B family as a versatile but discrete-function timer rather than a precision real-time clock. Keep the RC timing network close to the device, validate the selected output stage against the required interval, and confirm counter timing at the voltage and temperature extremes of the intended equipment. The 16-lead package also requires attention to lead pitch and footprint compatibility during replacement planning. This product record combines the functional architecture of the CD4536B family, package information, JEDEC qualification context, and practical timer-design guidance. It also distinguishes verified drop-in replacements from related counter ICs whose internal architecture or pin assignments make them unsuitable as direct PCB replacements.

RFQ پەیوەندی
CD4536BPW - 5MHz CMOS Programmable Timer | Texas Instruments
CD4536BPW

CD4536BPW - 5MHz CMOS Programmable Timer | Texas Instruments

Texas Instruments CD4536BPW is a CMOS programmable timer and counter built around 24 ripple-binary counter stages, with an operating frequency listed as high as 5 MHz and a 16-pin TSSOP package. The device supports counting from 1 to 2^24 or bypassing the first eight stages to select among 16 decoded outputs through four BCD control inputs. Its programmable architecture makes it suitable for timing, pulse generation, delay, and frequency-related control circuits. A programmable timer is a clock-and-timing IC that combines an internal oscillator, counter, decoding logic, and output circuitry to create timing events without requiring a microcontroller. In the broader semiconductor hierarchy, the CD4536BPW belongs to the CMOS timer family, the clock-and-timing IC category, and ultimately the integrated-circuit and semiconductor markets. It extends simple fixed-delay or fixed-frequency circuits by allowing the counter range and output selection to be changed with digital control signals. Key features include a 24-stage ripple-binary counter, selectable bypass of the first eight stages, four BCD inputs labeled A, B, C, and D, and selectable decoded outputs. A logic-high signal on the 8-BYPASS input makes stage 9 the first stage of the remaining 16-stage counter. The MONO IN input supports the on-chip monostable oscillator, while the device also offers programmable timer operation for longer timing intervals. The counter-based architecture is useful because the timing interval can be derived from the oscillator frequency and the selected count. When the eight bypassed stages are used, the decoder can select one of 16 outputs. This provides more flexibility than a simple fixed monostable pulse circuit and allows a system designer to choose among several timing taps. The Texas Instruments CD4536B datasheet also states that the B-series device provides standardized, symmetrical output characteristics and is 100% tested for quiescent current at 20 V. Typical uses include industrial pulse and delay generation, periodic event sequencing, laboratory timing circuits, counter interfaces, clock dividers, and embedded control systems where an external microcontroller does not need to manage every timed interval. A complementary counter or multiplexer can be useful when the selected timer output must be routed, counted, or isolated from other timing domains. Designers should account for the external resistor and capacitor network connected to the oscillator, verify propagation-delay behavior at the selected counter stage, and ensure that reset and output states remain defined during startup. Decoupling capacitors should be placed close to the supply and ground pins, while unused inputs must be connected to a defined logic level rather than left floating. This page consolidates the manufacturer timer architecture, verified package information, pinout guidance, application examples, and practical replacement considerations into a design-focused reference. It also distinguishes true same-footprint replacements from functionally related timer and counter ICs that require different packages or different internal architectures.

RFQ پەیوەندی
CD4541BCM - 100kHz Programmable Timer | onsemi | 14-SOIC
CD4541BCM

CD4541BCM - 100kHz Programmable Timer | onsemi | 14-SOIC

The onsemi CD4541BCM is a 100 kHz programmable timer CMOS IC with a 16-stage binary counter, integrated oscillator, output-control logic, and automatic power-on reset, housed in a 14-pin SOIC package. The oscillator accepts an external timing capacitor and two resistors, while the counter converts elapsed oscillator cycles into programmable timing intervals. Its integrated reset circuit initializes the timing sequence after power is applied, reducing the external control circuitry required in standalone timer designs. A programmable timer is a timing IC that generates an output after a selected delay. The CD4541 belongs to the CMOS counter and timer hierarchy, combining an oscillator, binary counter, reset function, and control outputs in one package. This integration makes it useful for delayed switching, periodic events, industrial timing modules, pulse generation, and embedded control systems where a microcontroller is unnecessary or unavailable. The principal device characteristics include a maximum oscillator frequency of 100 kHz, a 16-stage binary counting section, and an integrated power-on reset. The external resistor-capacitor network determines the oscillator timing, while counter and output-control logic determine how those cycles are presented at the outputs. The CD4541BCM is identified as a military-temperature-grade, 14-terminal gull-wing SOP device, making temperature qualification and package geometry important during replacement decisions. Internally, the oscillator provides the time base, the 16-stage binary counter accumulates oscillator transitions, and dedicated output logic controls the resulting outputs. The special power-on reset circuit establishes a defined timing state when power is applied. Because the oscillator timing elements are external, component tolerance, resistor temperature coefficient, capacitor stability, and PCB leakage can directly affect interval accuracy and should be included in the timing-error budget. Typical applications include industrial machinery interlocks, appliance delay circuits, test and measurement trigger sequencing, periodic pulse generation, power-control timers, and compact embedded timing modules. The integrated oscillator and counter are particularly useful when a system needs a simple autonomous interval rather than a software-driven timer. The 14-pin SOIC package also supports conventional surface-mount assembly and rework. For reliable timing, place the oscillator resistor and capacitor close to their associated pins, use resistor and capacitor tolerances appropriate for the required interval accuracy, and keep high-current switching loops away from the timing nodes. Verify startup behavior and output states over the complete supply-voltage and temperature range. A substitute should be checked for identical pinout, oscillator limits, counter length, output polarity, reset behavior, and package dimensions before it is treated as a drop-in replacement. This product overview combines the manufacturer-device description with engineering guidance on oscillator tolerances, power-on reset, PCB layout, and verified same-package replacement paths. It is designed to help engineers identify the function, inspect package compatibility, and select a replacement without overlooking the electrical details that govern timer accuracy.

RFQ پەیوەندی
CD4541BE - 100 kHz Programmable Timer | Texas Instruments
CD4541BE

CD4541BE - 100 kHz Programmable Timer | Texas Instruments

The Texas Instruments CD4541BE is a CMOS programmable timer and oscillator with a maximum oscillator frequency of 100 kHz, packaged in a 14-pin PDIP. It combines a 16-stage binary counter, an external RC-controlled oscillator, automatic power-on reset, and programmable output-control logic. According to the Texas Instruments datasheet, it is a high-voltage type rated for 20 V. A programmable timer is a timing IC that generates or measures intervals using digital counters and, often, an external resistor-capacitor network. In the broader electronics hierarchy, the CD4541BE belongs to CMOS logic, timer and oscillator circuits, and clock-and-timing semiconductors. Its internal oscillator establishes the time base, while the 16-stage counter divides that frequency to produce longer intervals or lower-frequency outputs. The MODE input, located at pin 10, provides selectable operating modes. With MODE at logic 1, the output is a continuous square wave whose frequency equals the oscillator frequency divided by 2N. With MODE at logic 0 following a master reset, the selected output changes according to the datasheet truth table. The device also supports reset control and allows the timer output stage to be selected by external logic. The CD4541BE is useful for periodic-event generation, delay circuits, clock dividers, and low-frequency waveform generation. Because the oscillator uses external resistors and a capacitor, the timing accuracy and frequency depend on the selected component tolerances and the stability of those external parts. Designers should avoid using the device where high-frequency precision beyond its specified 100 kHz capability is required. Typical uses include industrial control timing, relay and pulse generation, laboratory breadboard projects, low-frequency clock sources, and counter-based sequencing. A 14-pin PDIP package is convenient for prototyping and through-hole assembly, although it occupies more board area than a surface-mount timer package. For reliable timing, place the oscillator resistor and capacitor close to their associated pins, keep timing traces short, and provide adequate bypassing on the supply pins. Verify the selected MODE and reset levels in the manufacturer truth table before relying on a particular output waveform. This page consolidates the available manufacturer and distributor information, explicitly identifies missing electrical details, and avoids presenting unverified performance claims as product specifications.

RFQ پەیوەندی
CD4541BEX - CMOS Programmable Timer | Harris | 14-DIP
CD4541BEX

CD4541BEX - CMOS Programmable Timer | Harris | 14-DIP

The Harris Corporation CD4541BEX is a CMOS programmable timer IC with a 16-stage binary counter, an integrated oscillator using external resistors and a capacitor, output-control logic, and a power-on reset function. The device is packaged in a 14-lead rectangular dual in-line package measuring 0.300 inch, or 7.62 mm, across the pin row spacing. It is designed for timing, oscillator, delay, pulse-generation, and frequency-division circuits. A programmable timer is a clock-and-timing integrated circuit that divides an externally generated oscillator frequency into selectable timing intervals. The CD4541B family belongs to the CD4000 CMOS logic hierarchy and combines an oscillator, counter, reset control, and output stages in one package. This integration reduces the number of discrete timing components while giving the circuit designer control over frequency, count length, and output behavior. The CD4541BEX uses CMOS technology and includes an external-resistor-and-capacillator timing network. Its integrated 16-stage binary counter supports frequency division and elapsed-time measurement, while the oscillator section provides the time base. The special power-on reset circuit allows the device to operate across its full voltage range without an additional static power-consumption penalty associated with a conventional reset arrangement. The CD4541BEX is identified by a JESD-609 code of e0 and an industrial temperature grade. Its terminals use a tin/lead, Sn/Pb, finish. The 14-DIP package is through-hole rather than surface mount, making the device appropriate for conventional through-hole assemblies, prototyping, repair, and industrial control systems that retain 0.300-inch DIP footprints. Typical uses include delayed switching, retriggerable and non-retriggerable pulse generation, industrial sequence timing, periodic relay actuation, low-frequency clock generation, and frequency division. In these applications, external timing components establish the oscillator rate, while the counter and control inputs determine when an output changes state. Layout should keep the oscillator resistor, capacitor, and associated traces away from high-current switching nodes to reduce false frequency triggering. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be held at defined logic levels. Because this version uses a tin/lead terminal finish, buyers should assess its environmental and assembly-policy requirements before use. This page combines the manufacturer timer architecture with practical oscillator-layout guidance, application-specific selection criteria, and a structured comparison of documented CD4541-family alternatives. It also distinguishes verified electrical facts from parameters that require confirmation from the device datasheet before production release.

RFQ پەیوەندی