بەرهەمەکان (770+)

MAX77839AEWL+T - 5.5V 6µA IQ Buck-Boost | Analog Devices
MAX77839AEWL+T

MAX77839AEWL+T - 5.5V 6µA IQ Buck-Boost | Analog Devices

The Analog Devices MAX77839AEWL+T is a low-IQ buck-boost voltage regulator IC with a 1.8V to 5.5V input range, 2.3V to 5.3V adjustable output, and 6µA quiescent current, housed in a 15-WLP package measuring 2.07mm by 1.51mm. It targets one-cell Li-ion and other battery chemistries that can discharge down to 1.8V. A buck-boost converter belongs to the switching-regulator hierarchy: unlike a linear regulator, it can regulate the output above or below its input. The MAX77839 therefore supports a stable rail when a battery voltage crosses the required output level. Its compact package and low quiescent current are particularly useful in wearable, mobile, and other battery-powered equipment. Key verified features include 4.4A/3.6A switching-current ratings, a single-resistor adjustable output from 2.3V to 5.3V, and a configurable GPIO pin that can select forced-PWM control input or power-good open-drain output. Maxim's buck-boost controller technology provides high efficiency and seamless transition between buck and boost operation. The topology dynamically regulates in either direction as the battery changes state. This differs from a buck-only converter, which cannot maintain an output above the input, and a boost-only converter, which cannot reduce an excessive input voltage. The available switching-current ratings also require careful inductor, capacitor, thermal, and PCB validation for the selected output voltage and load. Typical applications include low-power wearables, smartphone accessories, one-cell portable equipment, Bluetooth-connected devices, and compact embedded systems. The MAX77839 evaluation kit can support hardware evaluation, with different MAX77839 variants selected according to whether POK functionality is required. Designers should verify the complete WLP land pattern and pin assignments against the manufacturer datasheet before layout. Inductor selection, compensation, capacitor sizing, current rating, and layout must be derived for the required load because the supplied verified data does not provide values for those implementation details. This page consolidates the verified manufacturer and distributor information, separates documented performance from missing engineering data, and records why no unverified drop-in substitute is recommended. That evidence-first approach helps engineers evaluate the MAX77839 without treating generic regulators as pin-compatible replacements.

RFQ پەیوەندی
MAX798ESE - 30V 10A Synchronous Buck Controller | Maxim
MAX798ESE

MAX798ESE - 30V 10A Synchronous Buck Controller | Maxim

The Maxim Integrated MAX798ESE is a synchronous step-down DC-DC controller designed for CPU power in battery-powered systems, with a 4.5 V to 30 V input range, output capability up to 10 A, and a 16-pin SOIC package. It reaches 96% efficiency by coordinating a synchronous high-side switch, low-side synchronous rectifier, and precision feedback control. A synchronous buck controller is a voltage-regulator IC that controls switches to reduce a higher input voltage to a lower regulated output. The MAX798 belongs to the DC-DC converter, voltage regulator, and power-management IC hierarchy. Unlike a linear regulator, a buck controller actively transfers energy through switching components, making it suitable for higher current and larger input-to-output voltage differences than a simple linear dropper. The controller provides one adjustable output, with a reported output range of 1.6 V to 6 V. Its current-mode architecture operates at up to 330 kHz, while the MAX798 family is also described as a high-accuracy step-down controller with synchronous rectification. Its 96% efficiency is particularly useful in battery-powered equipment because it reduces the power loss associated with converting battery energy into a low-voltage processor rail. MAX798 control circuitry manages the transition between operating states and supports battery-focused power conversion. The synchronous-rectifier arrangement reduces conduction loss during the lower-switch interval, while current-mode control provides a controlled inductor-current response. Designers must still select the external MOSFETs, inductor, output capacitors, and compensation network to match the required load and switching performance. Typical uses include notebook-computer and portable-system CPU rails, battery-powered instrumentation, industrial handheld equipment, and embedded processors requiring a compact, high-efficiency 1.6 V to 6 V supply. The 16-pin SOIC package supports conventional surface-mount assembly, although exposed-pad thermal performance is not specified for this variant. When designing the converter, verify the external MOSFET voltage and current ratings against the 30 V maximum input. Place the high-current switching loop compactly, connect the power ground and signal ground carefully, and use the datasheet pin-description table when assigning every NC and functional terminal. Component selection should also account for startup, transient response, and thermal rise at the 10 A design limit. This page organizes the controller's electrical limits, package details, application guidance, design checks, and documented family relationships into a practical engineering reference. It also distinguishes a verified replacement from related or differently ordered MAX79x devices, helping engineers avoid assuming that similar descriptions guarantee pin compatibility.

RFQ پەیوەندی
MAXM17514ALI+ - 4A 2.4-5.5V Step-Down Power Module | Maxim
MAXM17514ALI+

MAXM17514ALI+ - 4A 2.4-5.5V Step-Down Power Module | Maxim

The Maxim MAXM17514ALI+ is a fixed-frequency step-down DC-DC switching regulator power module in a thermally-efficient system-in-package (SiP) that operates from a 2.4V to 5.5V input supply and delivers up to 4A of output current across a programmable 0.75V to 3.6V output range. The module integrates a switch-mode power-supply controller, dual n-channel MOSFET power switches, a fully shielded inductor, and compensation components into a single surface-mount package, eliminating the discrete buck converter design effort for low-voltage, high-current rails. A step-down (buck) DC-DC converter is a switching voltage regulator that efficiently reduces a higher DC input voltage to a lower DC output voltage by rapidly switching an inductor and rectifying the resulting waveform. Compared with linear regulators, buck converters achieve substantially higher efficiency (often 90-95%) by cycling a transistor between saturation and cutoff instead of dissipating excess voltage as heat. Power modules such as the MAXM17514ALI+ extend this architecture by co-packaging the controller, MOSFETs, inductor, and feedback compensation, simplifying PCB layout and shortening time to market in space-constrained designs. Key specifications include a 2.4V to 5.5V input voltage window, 0.75V to 3.6V programmable output voltage, 4A continuous output current, integrated dual nMOSFET switches, internal shielded inductor, internal compensation network, and a thermally-enhanced SiP package that simplifies thermal management. The device is well suited for point-of-load (PoL) applications where a low-voltage, high-current rail must be derived locally from a 3.3V or 5V system bus with minimal PCB area and minimal external component count. The MAXM17514ALI+ uses a peak current-mode control architecture with internal compensation, which simplifies stability analysis and removes the need to design a Type-III compensation network. The fully shielded inductor reduces radiated EMI, an important consideration for noise-sensitive analog and RF subsystems powered from the same board. Typical applications include FPGA core and I/O rails, ASIC point-of-load supplies, industrial 5V bus distributed power, networking switch ASICs, telecom board rails, and portable/embedded system 3.3V-to-1.xV conversion. The wide input range makes it compatible with both 3.3V and 5V system buses without external front-end regulation. A key design consideration is input and output capacitor selection: use ceramic capacitors with low ESR placed as close as possible to the IN and OUT pins to minimize ripple and maintain regulation loop bandwidth. Ensure the upstream 5V or 3.3V source can supply the full 4A load transient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster component selection and supply chain decisions.

RFQ پەیوەندی
MAXM17630AME+T - 1A, 36V Himalaya uSLIC Step-Down Module | ADI
MAXM17630AME+T

MAXM17630AME+T - 1A, 36V Himalaya uSLIC Step-Down Module | ADI

The Analog Devices (formerly Maxim Integrated) MAXM17630AME+T is a Himalaya-series, non-isolated synchronous step-down DC-DC power module with integrated controller, MOSFETs, compensation components and inductor, delivering 1A continuous output current at 3.3V fixed from a 4.5V to 36V input rail. Housed in a 16-pin EMGA (3 mm x 3 mm) uSLIC surface-mount package, it operates at a switching frequency of up to 1.5 MHz and targets point-of-load (PoL) applications where PCB area is constrained. A step-down DC-DC module (or buck converter module) is a complete switching power supply building block that integrates the controller, power switches, inductor and feedback compensation inside a single surface-mount package. Compared with discrete buck designs, a uSLIC module reduces external component count to essentially one input capacitor, one output capacitor and two small resistors, while delivering factory-tuned loop stability. As a member of the broader category of switching voltage regulators and DC-DC converters, it sits above linear regulators in efficiency for high input-to-output voltage deltas, converting excess voltage as switching losses rather than heat. Key features include 4.5V to 36V input range, 3.3V fixed output (AME variant), 1A continuous load current, peak-current-mode control with internal compensation, and PFM/PWM auto-skipping at light loads for high efficiency. The internal MOSFETs and synchronous rectification eliminate the external Schottky diode. Hiccup-mode overcurrent protection, thermal shutdown, and an enable/UVLO pin provide fault handling for industrial and consumer rails. Efficiency peaks above 88% at 12Vin/3.3Vout/0.5A and remains above 80% across the 4.5V to 36V input range. Typical applications include industrial 24V/12V point-of-load regulation, factory automation sensors, HVAC control boards, distributed 5V/3.3V rails, and space-constrained embedded systems requiring minimal external component count. The 3 mm x 3 mm footprint and integrated inductor make it especially attractive when a discrete buck solution would consume more than 4x the PCB area. When designing with the MAXM17630AME+T, place the input ceramic capacitor as close as possible to the PGND and IN pins to minimize switching noise injection; a 1 µF to 4.7 µF X7R ceramic is typically sufficient. The exposed pad must be soldered to a copper pour of at least 25 mm² to keep the junction temperature below 125 °C at full 1A load and 36V input. Avoid routing analog signal traces directly beneath the module to prevent radiated switching noise coupling. This page synthesizes distributor pricing, drop-in alternatives drawn from the MAXM17630/MAXM17631/MAXM17632 family, application notes, and practical PCB layout guidance that goes beyond the manufacturer datasheet alone.

RFQ پەیوەندی
MAXM17634AMG+ - 36V 2A 5V uSLIC Step-Down Module | Analog
MAXM17634AMG+

MAXM17634AMG+ - 36V 2A 5V uSLIC Step-Down Module | Analog

The Analog Devices MAXM17634AMG+ is an integrated 2A, 5V synchronous step-down DC-DC power module with a 4.5V to 36V input range, packaged in the MAXM17634AMG+ module format. It belongs to the Himalaya uSLIC family, which integrates the controller, MOSFETs, compensation components, and inductor into one compact module. The verified distributor listing specifies one 5V output, 2A output current, and 4.5V to 36V input range. Its integrated architecture reduces external power-conversion component count while retaining the efficiency and thermal advantages of synchronous buck conversion. The module is intended for industrial, communications, robotics, embedded computing, and distributed-power applications requiring a regulated 5V rail from a wide input bus. A DC-DC converter is a power-management IC category that changes one direct-current voltage level into another. A synchronous step-down converter uses high-side and low-side switching transistors, rather than a simple linear pass element, to transfer energy efficiently from a higher input voltage to a lower regulated output. MAXM17634AMG+ is a module-level implementation because its magnetic and compensation elements are integrated with the switching silicon. The MAXM17634AMG+ family provides a wide 4.5V to 36V operating input range, supporting both conventional 5V, 12V, and 24V systems and higher transient-capable industrial buses. According to the Analog Devices manufacturer datasheet, MAXM17633, MAXM17634, and MAXM17635 employ peak-current-mode control. Programmable soft-start reduces input inrush current. For the MAXM17634 variant, the verified distributor data identifies a fixed 5V output and 2A capability. The integrated Himalaya module approach can simplify PCB layout by reducing the number of externally placed power-stage components. It is particularly useful when designers want repeatable power-conversion behavior without tuning an external inductor and compensation network. The tradeoff is lower design flexibility than a discrete synchronous buck implementation, because the integrated inductor and compensation determine much of the module's electrical and thermal behavior. Typical uses include industrial control systems, 24V bus-powered equipment, embedded single-board computers, robotics platforms, communications equipment, and compact industrial sensors. The 5V rail can feed processors, sensor interfaces, USB-powered peripherals, or other loads, subject to the complete power budget and thermal verification. For battery applications, the module's input range and current rating must be checked against the source voltage, discharge profile, and required output headroom. Designers should follow the manufacturer datasheet for input and output capacitor selection, PCB layout, exposed-pad or thermal-pad treatment, startup behavior, and current derating. Keep the power loop compact, provide adequate copper for heat dissipation, and verify both continuous-load temperature rise and transient response. Do not assume that the 2A rating applies without accounting for VIN, VOUT, efficiency, ambient temperature, and board thermal resistance. This page combines verified distributor information, the manufacturer datasheet, package-level data, and design guidance for efficient sourcing and first-board bring-up. MAXM17634AMG+ is best suited to compact 5V power rails where integrated magnetics, wide input voltage, synchronous efficiency, and soft-start control outweigh the flexibility of a discrete converter. For exact capacitor values, pin details, switching frequency, efficiency curves, and approved layout geometry, consult the official MAXM17633/MAXM17634/MAXM17635 datasheet and Analog Devices product page.

RFQ پەیوەندی
MBCM270F450M270A00 - 270W 230-330V to 45V BCM Bus Converter | Vicor
MBCM270F450M270A00

MBCM270F450M270A00 - 270W 230-330V to 45V BCM Bus Converter | Vicor

The Vicor MBCM270F450M270A00 is a high-efficiency (>96.0%) Sine Amplitude Converter (SAC) BCM bus converter module that operates from a 230V to 330V primary bus and delivers an isolated 38.3V to 55.0V secondary voltage at up to 270W (6A) of output power in a VI Chip surface-mount package. It is part of Vicor's MIL-COTS BCM family and is engineered to provide an isolated, fixed-ratio unregulated bus voltage that feeds downstream Point-of-Load (PoL) converters in high-voltage distributed power architectures. A BCM bus converter is a fixed-ratio isolated DC-DC converter that uses a SAC topology to step down (or step up) a high-voltage bus to an intermediate, isolated distribution voltage with extremely high efficiency and power density (>919 W/in3). In the power system hierarchy, BCMs sit between a front-end AC-DC or HV DC-DC source and downstream regulators (PoL converters such as Vicor's PRM/VTM or ZVS buck regulators). The fixed K factor (K=1/5 for this 270V-in / 45V-out part) means output voltage tracks input voltage by a precise ratio, eliminating the need for a closed-loop control loop on the BCM itself. Key features include >96.0% peak efficiency, >919 W/in3 power density, integrated input-side enable/disable control, an input-side referenced temperature monitor signal, and built-in protection features. The VI Chip package is compatible with standard pick-and-place and surface-mount assembly processes, reducing system power footprint by more than 40% compared with discrete converter designs. The fixed-ratio SAC topology produces a clean, low-noise secondary output because it transfers energy as a sinusoidal current waveform rather than through a switched-inductor PWM stage. Typical applications include HV-to-LV isolated bus distribution in industrial automation, 270V/280V aerospace and military power systems, MIL-COTS telecom equipment, and front-end power for downstream PoL converters. The MBCM270F450M270A00's high efficiency and power density make it well-suited for size- and weight-constrained applications such as UAV power distribution, ground-vehicle electronics, and shipboard power systems. The 230-330V input range covers the nominal 270V and 280V MIL-STD-704 and DO-160 aircraft buses as well as 300V nominal industrial DC buses. When designing with this device, the BCM output is unregulated, so downstream regulation is required for any load that requires a precise voltage. Place input bulk capacitance close to the BCM input pins to handle the sinusoidal input current ripple, and ensure the secondary-side capacitance meets Vicor's recommended minimum to filter the SAC output. The enable pin is referenced to the input side, so an isolated gate driver or digital isolator is required when controlling enable from a low-voltage controller on the secondary side. This page synthesizes distributor stock and pricing, MIL-COTS-compatible variants, and design notes for HV distributed power architectures - context not found in the standalone datasheet.

RFQ پەیوەندی
MC33063AD - 1.5A Buck/Boost/Inverting DC-DC Converter | Texas Instruments
MC33063AD

MC33063AD - 1.5A Buck/Boost/Inverting DC-DC Converter | Texas Instruments

The Texas Instruments MC33063AD is a monolithic switching regulator IC containing all primary functions required for building simple DC-DC converters in buck, boost, and inverting topologies. Housed in an 8-pin SOIC (D) package with 3V to 40V input voltage range, the MC33063AD integrates a temperature-compensated 1.25V reference, a comparator, a duty-cycle-tunable oscillator up to 100 kHz, an active current-limiting PWM controller, a driver, and a high-current 1.5A Darlington output switch. It is specified over the -40C to +85C industrial operating temperature range. A switching regulator is a power management IC that converts one DC voltage to another by repeatedly switching energy through an inductor, then filtering with capacitors. The MC33063AD belongs to the SMPS controller family (switched-mode power supply) -> DC-DC converter -> voltage regulator -> power management IC -> semiconductor. Compared to linear regulators, switching converters like the MC33063AD achieve 70-95% efficiency even at large input-to-output voltage deltas, making them ideal when thermal dissipation must be minimized or when the input voltage is much higher than the output. Key features include a 1.5A peak switch current rating, an adjustable output voltage down to 1.25V, internal current limiting via a single external resistor, and an external resistor-programmable oscillator frequency from approximately 100 Hz to 100 kHz. The 8-SOIC package provides standard surface-mount manufacturability and is footprint-compatible with the MC34063A (commercial 0-70C) and MC33063ADG (onsemi second source). Architecturally, the device uses a bipolar Darlington output switch, a transconductance error amplifier referenced to the internal 1.25V bandgap, and a flip-flop synchronized to the on-chip oscillator. This classic 1970s architecture remains popular because the design requires only a handful of external parts (inductor, capacitor, diode, sense resistor, feedback divider) and provides predictable behavior across a wide input range. Typical applications include cost-sensitive step-down converters for 12V/24V industrial buses, boost converters for battery-powered systems needing 5V or higher rails, and negative-voltage inverters for op-amp and analog signal-chain supplies. The internal switch and current limit also make it suitable for LED drivers and simple motor speed controllers operating from single-cell Li-ion or multi-cell lead-acid sources. When designing with the MC33063AD, ensure the inductor saturation current exceeds the internal current-limit threshold, and verify that the catch diode reverse voltage rating exceeds the maximum input supply. PCB layout should keep the switch-current loop (pin 1, inductor, catch diode) compact to minimize switching noise. This page synthesizes distributor pricing, drop-in alternatives from TI and onsemi, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
MC33063ADG4 - 1.5A Buck/Boost/Inverting Switching Regulator | TI
MC33063ADG4

MC33063ADG4 - 1.5A Buck/Boost/Inverting Switching Regulator | TI

The Texas Instruments MC33063ADG4 is a monolithic DC-DC switching regulator controller IC rated for 1.5 A peak switch current, supporting buck, boost, and inverting topologies in an 8-pin SOIC package. It integrates a temperature-compensated 1.25 V reference, a duty-cycle-controlled oscillator (up to 100 kHz), a comparator, an active current-limit circuit, a driver, and a high-current output switch on a single die. The wide 3 V to 40 V input range and adjustable 1.25 V to 40 V output make it a versatile single-chip solution for non-isolated point-of-load conversion. A switching regulator is a power-conversion IC that uses an energy-storage element (inductor or transformer) and a switching transistor to transfer energy from input to output at high efficiency, unlike a linear regulator which dissipates the VIN-VOUT differential as heat. The MC33063 family belongs to the SMPS (Switched-Mode Power Supply) controller hierarchy: switching regulator -> DC-DC converter -> power management IC. Within that hierarchy, the MC33063 occupies the 'all-in-one controller + internal switch' tier that lets engineers build a complete converter with a handful of external passive components and one Schottky rectifier. Key features include a 2% internal reference, 100 kHz maximum oscillator frequency, short-circuit protection via the current-sense comparator, and a guaranteed 1.5 A output switch. The exposed thermal pad (DAP) on the SOIC-8 package lowers thermal resistance versus a standard SOIC-8, allowing continuous operation near the 1.5 A switch limit at moderate ambient temperatures. The same silicon die is offered across the MC33063 (industrial -40C to +85C), MC34063 (commercial 0C to +70C), and MC33063A (extended voltage tolerance) families, giving designers direct drop-in migration paths. The architecture is built around a current-mode control loop: the internal comparator monitors the output voltage via a resistor divider, the oscillator sets the switching period, and the on-time is modulated to keep VOUT in regulation. The integrated Darlington output switch drops about 1.5 V at full load, so for 5 V outputs from a 12 V rail, efficiency reaches roughly 80 percent. Compared with newer TI WEBENCH-targeted controllers, the MC33063 is a low-cost, well-documented legacy part that remains in service due to its simplicity, broad input range, and second-source availability. Typical applications include non-isolated point-of-load converters in industrial controls, 24 V to 5 V auxiliary rails in factory automation, negative bias supplies for op-amps and LCDs, battery chargers with current limiting, and distributed 12 V buss regulators in telecom and automotive subsystems. Its 40 V input tolerance also suits automotive load-dump-protected rails. When designing with this part, select the timing capacitor CT to set the oscillator near 30-50 kHz for typical buck or boost designs; lower frequencies improve efficiency but require larger inductors. Place the catch diode and inductor close to the switch pin to minimize parasitic inductance, and use a low-ESR output capacitor to limit ripple. The current-sense resistor RS determines peak switch current and therefore the converter's load capability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in a single manufacturer document.

RFQ پەیوەندی
MC33063ADR - 1.5A Buck/Boost/Inverting Switching Regulator | TI
MC33063ADR

MC33063ADR - 1.5A Buck/Boost/Inverting Switching Regulator | TI

The Texas Instruments MC33063ADR is a 1.5 A peak switching regulator controller IC implementing all primary functions needed for step-down (buck), step-up (boost), and inverting DC-DC converters in a single 8-pin SOIC package. The device operates from a 3 V to 40 V input range, delivers an adjustable output voltage from 1.25 V to 40 V, and supports switching frequencies up to 100 kHz, addressing cost-sensitive industrial, automotive, and consumer power designs. An SMPS controller (switched-mode power supply controller) is an IC that drives an external power switch (typically a BJT or MOSFET) at a programmed duty cycle to convert one DC voltage to another. The MC33063A family belongs to the SMPS controller -> DC-DC converter -> power management IC hierarchy, and is among the longest-lived TI part numbers, serving as a baseline for thousands of cost-optimized designs since its original bipolar 34063 release. Key features include a precision 2 % internal bandgap reference, duty-cycle-controlled pulse-width modulator, internal current limiting, and an internal output switch rated at 1.5 A peak. The adjustable output uses a single external resistor divider, and the oscillator timing capacitor sets the switching frequency. The integrated switch and short-circuit protection simplify BOM count to as few as five external components. Architecture-wise, the MC33063ADR combines a temperature-compensated reference, a duty-cycle comparator, an oscillator with active-high output, a current-limit comparator with 250 mV threshold, and a Darlington output driver. The bipolar process delivers robust SOA but at lower efficiency than CMOS alternatives, making the part best suited to moderate-power applications rather than battery-critical portable loads. Typical applications include non-isolated point-of-load converters, 12 V to 5 V automotive accessory rails, LCD bias supplies, and simple inverting supplies for op-amp negative rails. The wide 3 V-40 V input range allows direct connection to industrial 24 V buses. When designing with this device, choose inductor value to keep peak switch current below 1.5 A and use a Schottky catch diode to maximize efficiency. The timing capacitor CT should be selected to keep switching frequency between 30 kHz and 100 kHz to balance efficiency and EMI. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not consolidated in the manufacturer datasheet, providing an AEO-optimized reference for engineers sourcing the MC33063ADR.

RFQ پەیوەندی
MC33262PG - CRM PFC Controller, 12-28V | onsemi
MC33262PG

MC33262PG - CRM PFC Controller, 12-28V | onsemi

The onsemi MC33262PG is a critical-conduction-mode power factor correction controller designed for boost-preconverter front ends in electronic ballasts and off-line power converters. The device operates from a 12 V to 28 V supply range, draws 6.5 mA of supply current, provides overvoltage protection, and uses a 50 kHz nominal switching frequency. It is supplied in an 8-pin plastic dual in-line package. The verified distributor listing identifies it as a PFC IC with Critical Conduction Mode operation. A PFC controller is a power-management IC that shapes the input current drawn from an AC source so that current and voltage are more nearly in phase. The MC33262 family places this function in a boost-converter control block placed ahead of a downstream rectifier and regulator. Improving power factor reduces reactive current and can reduce input-current stress, while critical-conduction mode supports controlled operation around the inductor-current transition. The controller is therefore positioned within the hierarchy AC input conversion, power factor correction, boost preconverter, power management IC, and semiconductor. Key verified attributes include an internal startup timer for standalone operation, a one-quadrant multiplier for near-unity power factor, and a zero-current detector for critical-conduction operation. The MC33262PG family is intended for electronic-ballast and off-line power-converter applications. Its 12 V to 28 V operating supply range is suited to rectified auxiliary buses commonly found in such equipment, while the 50 kHz nominal operating point places it in a useful control range for compact boost stages. The controller architecture supports independent sensing of the input and output voltage conditions through its externally connected pins. Designers must still provide the boost-inductor, switching transistor, rectifier, sensing network, timing components, and output-discharge provisions appropriate to the target converter. The zero-current detector and critical-conduction control reduce the risk of uncontrolled switch conduction, but component tolerances, propagation delays, and magnetic design remain important to stable power-factor correction. Typical applications include electronic ballasts, off-line AC-DC converters, switched-mode power supplies with active PFC, and industrial power systems that need reduced input-current distortion. The 8-PDIP package is through-hole and is mechanically convenient for leaded assemblies, repair products, and prototypes. It is not the same as an SOIC-8 package, so PCB or lead-frame substitution must be checked before reuse. For a new design, select the MOSFET, inductor, current-sense resistor, and optical or display feedback components against the required output power and voltage. Confirm the controller's 12 V minimum operating supply, 28 V maximum stated range, and the designer's surge requirements under worst-case mains conditions. Because the verified excerpt does not provide complete maximum ratings, timing values, protection thresholds, or thermal limits, consult the manufacturer datasheet before release to production. This page combines verified distributor identification, official family information, application context, packaging guidance, and a conservative replacement framework. It distinguishes confirmed MC33262PG attributes from parameters that still require full datasheet review, helping engineers identify the correct power factor controller without conflating it with unrelated MC33269 regulator data.

RFQ پەیوەندی
MC33368D - High-Voltage Critical Conduction PFC | onsemi
MC33368D

MC33368D - High-Voltage Critical Conduction PFC | onsemi

The onsemi MC33368D is a high-voltage GreenLine power factor correction controller in a narrow-body 16-pin SOIC package. It operates as a critical-conduction-mode, or CRM, boost PFC controller for off-line power supplies, supporting low-power, high-density designs that emphasize reduced component count, reduced board area, and low power dissipation. The verified distributor data identifies the device as a critical-conduction PFC IC and the manufacturer datasheet identifies it as an active power-factor controller for boost preconverter applications. A power-factor controller is a power-management IC that shapes input current to improve the real-power factor of AC-to-DC equipment. In the broader hierarchy, the MC33368D belongs to the PFC controller class, then power-management ICs, and ultimately semiconductor devices used in offline power conversion. CRM operation reduces the switching loss associated with continuously conducting current and is commonly considered for compact power supplies where component count and thermal performance are important. The MC33368D family is intended for boost preconverter front ends used ahead of downstream DC-DC converters. Its narrow-body SOIC package helps reduce board area, while the CRM control approach supports low-power, high-density power-supply implementations. The available evidence confirms the 16-SOIC package, critical-conduction operation, boost PFC function, high-voltage application class, and the manufacturer’s GreenLine positioning. Exact input-voltage, switching-frequency, current-limit, timing, and electrical-limit values were not included in the supplied verified excerpts and are therefore not inferred here. Typical applications are off-line power supplies, compact AC-to-DC adapters, industrial power-conversion equipment, and consumer electronics with an upstream PFC stage. In these systems, the controller drives the boost switching element while external circuitry handles current sensing, voltage feedback, rectification, filtering, and protection. The MC33368D can help reduce conducted emissions and improve input-current quality when the complete PFC loop is designed and compensated correctly. The main design consideration is that PFC performance depends on the surrounding converter, not only on the controller IC. Inductor selection, current-sense network, switch and diode ratings, safety spacing, feedback compensation, EMI filtering, and thermal design must be validated together. The narrow SOIC-16 footprint helps layout density, but high-voltage offline designs still require careful creepage, clearance, isolation, and safety-capacitor placement. This product page synthesizes verified manufacturer and distributor information, package identity, application context, engineering design notes, and honest sourcing limitations for MC33368D. Because the supplied data does not include a confirmed drop-in substitute, no replacement MPN is presented as drop-in compatible.

RFQ پەیوەندی
MC33FS6520NAE - 2.2A Vcore SBC with CAN FD | NXP
MC33FS6520NAE

MC33FS6520NAE - 2.2A Vcore SBC with CAN FD | NXP

NXP Semiconductors MC33FS6520NAE is an active FS6500 system basis chip with a 2.2 A Vcore DC/DC converter, 48-HLQFP (7 × 7 mm) package, and integrated communication and safety functions. The device supplies programmable MCU power while combining switching and linear regulation with advanced functional-safety measures for ASIL B/D applications. According to the NXP product page, it also provides SPI control and diagnostics plus CAN FD and LIN physical-interface integration. A system basis chip is a mixed-signal power-management and communication IC placed beside an automotive microcontroller. In the device hierarchy, an SBC sits above DC/DC converters, linear regulators, wake logic, diagnostics, and vehicle-network transceivers. Rather than distributing every rail, control function, and network interface across separate components, the FS6500 consolidates them near the MCU to simplify design, reduce board area, and support deterministic power management. The verified data identifies a 2.2 A Vcore regulator, a system basis chip architecture, advanced functional-safety measures targeting ASIL B/D systems, SPI control and diagnostics, and CAN FD/LIN physical interfaces. Other independent results identify moisture sensitivity level 3, a 40-second maximum time at peak reflow temperature, a 260°C peak reflow temperature, and AEC-Q100 screening. These details matter because automotive electronics must combine electrical performance with controlled assembly and production screening. The device is intended for automotive embedded systems in which an MCU needs several regulated rails, low-power operating modes, network wake-up, diagnostic access, and safety monitoring. Integrating the MCU power subsystem and vehicle-network interfaces can reduce duplication while giving the host processor a centralized control path. SPI configuration supports firmware-controlled sequencing and diagnostics, while functional-safety features support systems designed around ISO 26262 objectives. Typical uses include body controllers, gateway platforms, comfort systems, powertrain-adjacent controllers, and distributed electronic control units. The CAN FD interface suits high-bandwidth vehicle backbones, while LIN supports lower-cost peripheral networks. Exact voltage ranges, regulator outputs, pin functions, electrical limits, and package dimensions must be confirmed in the manufacturer datasheet before schematic or layout release. Designers should preserve the exposed-pad thermal path, place high-current and communications circuitry according to the manufacturer layout guidance, and validate startup, undervoltage, fault-response, and network behavior in the final vehicle environment. Automotive qualification does not remove the need for system-level ISO 26262 work or EMC validation. This page consolidates verified manufacturer and distributor information, including package, regulator class, communications support, lifecycle status, purchasing references, and practical qualification considerations. It also identifies missing numeric data explicitly rather than estimating unverified electrical limits.

RFQ پەیوەندی
MC34063ABD-TR - 1.5A Buck/Boost DC-DC Converter | STMicroelectronics
MC34063ABD-TR

MC34063ABD-TR - 1.5A Buck/Boost DC-DC Converter | STMicroelectronics

The STMicroelectronics MC34063ABD-TR is a monolithic DC-DC switching regulator control circuit supporting buck, boost, and inverting topologies with a 3V to 40V input range, an adjustable 1.25V to 38V output, and a 1.5A (switch) current capability, housed in an 8-pin SOIC package. A switching regulator IC is a power management device that converts one DC voltage level to another using switching elements (an internal transistor plus an external inductor and diode) rather than dissipative linear pass elements, achieving far higher efficiency. Within the power management hierarchy, the MC34063ABD-TR belongs to the DC-DC converter controller family, sitting below integrated modular converters but above bare PWM controllers because it integrates the oscillator, comparator, reference, and output switch in one die. Key features include an internal temperature-compensated 1.25V reference with 2% accuracy, a duty-cycle-controlled oscillator operating up to 100 kHz, active current limiting via the Ipk sense pin, and low 2.5 mA typical quiescent current. These specifications make it suitable for battery-powered and cost-sensitive designs where a full-featured modern controller is unnecessary. Architecturally, the device combines a comparator, gated oscillator latch, driver, and high-current Darlington output switch. Output voltage is set by two external resistors dividing the output down to the 1.25V reference at the comparator input, enabling step-down, step-up, or voltage-inverting converter configurations with minimal external components. Typical applications include automotive USB charger adapters stepping 12V or 24V down to 5V, negative voltage rails for op-amp supplies in industrial instrumentation, and boost conversion from single-cell or low-voltage supplies in consumer products. Design consideration: keep the oscillator timing capacitor and current-sense resistor values consistent with peak current requirements, and place the inductor and catch diode close to the IC to limit switching loop area; the device tolerates board-level noise well but efficiency drops at higher output currents. This page synthesizes distributor pricing, drop-in alternatives across ST, onsemi, and Texas Instruments, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-10-12.

RFQ پەیوەندی
MC34129DR2 - Current Mode Switching Regulator for Telecom | NXP
MC34129DR2

MC34129DR2 - Current Mode Switching Regulator for Telecom | NXP

The NXP MC34129DR2 is a high-performance current-mode switching regulator supplied in a 14-pin SOIC package, designed specifically for low-power digital telephone systems. It operates from a 4 V to 12 V supply and delivers a regulated output while drawing only 2.5 mA of quiescent supply current, with the SO-14 (SOIC-14) outline suitable for compact telecom line cards and subscriber equipment. A current-mode switching regulator is a type of DC-DC converter that uses the peak inductor current as the inner control loop rather than output voltage alone. The MC34129 belongs to the SMPS (Switched-Mode Power Supply) controller family, which sits within the broader hierarchy of power management ICs (PMICs) used to derive stable rails from telecom battery feeds. Current-mode control provides inherent cycle-by-cycle current limiting, simplified loop compensation, and good line-transient response, making it well suited to non-isolated point-of-load converters in 24 V to 48 V backplane environments. Key features include an internal fault timer with automatic restart for overload recovery, duty-cycle clamp, and an on-chip start-up circuit. The 14-SOIC surface-mount package supports automated assembly, and the part is qualified over the 0 °C to 70 °C commercial operating range. Its low quiescent current of 2.5 mA and wide 4 V to 12 V input range target battery-backed telecom rails where efficiency and restart behavior after a short circuit are critical. In typical application the device is wired as a step-down (buck) converter with an external MOSFET switch, inductor, and flyback Schottky diode. The current sense is taken from a low-side resistor in series with the inductor, and a single feedback resistor divider programs the output. The fault timer automatically initiates a soft restart after sustained overload, removing the need for an external watchdog. Typical applications include digital telephone subscriber line interface circuits (SLICs), central-office line cards, ISDN terminal adapters, and other low-power telecom points-of-load. The wide supply range also supports industrial 12 V bus systems. When designing with this part, place the current-sense resistor within 1 cm of the sense pin and keep the high-current switching loop area to a minimum to limit conducted EMI on the telecom line.

RFQ پەیوەندی
MC34702EKR2 - 3A Switch-Mode PMIC with LDO | NXP
MC34702EKR2

MC34702EKR2 - 3A Switch-Mode PMIC with LDO | NXP

The NXP MC34702EKR2 is a 3.0 A switch-mode power supply with integrated linear regulator, housed in a 32-pin SOIC (0.295 inch / 7.50 mm width) package. It provides the means to efficiently supply Freescale Power QUICC I, II, and other families of Freescale microprocessors and DSPs, integrating a high-current buck switcher and a low-dropout linear post-regulator on one die. A switch-mode power supply (SMPS) with integrated linear regulator is a hybrid power management IC that combines a high-efficiency step-down switching converter for bulk current delivery with a low-noise linear regulator for noise-sensitive downstream rails. In the system hierarchy it sits within power management ICs (PMICs) -> DC-DC converters -> synchronous buck regulators -> microcontroller companion supplies, providing both the high-current core rail and a clean auxiliary rail from a single IC. Key features include a wide 2.8 V to 6 V supply input range, 60 mA typical quiescent current, 3.0 A peak switch current capability, and built-in power sequencing that follows the supply rail during power-up and power-down in line with microcontroller requirements. The linear regulator channel provides a low-noise post-regulated output, while the switching channel handles bulk load transients efficiently. The device uses a peak current-mode control architecture with internal compensation, eliminating most external compensation components and simplifying the LC filter design. During power-up and power-down, both the switcher and linear regulator outputs follow the supply rail within the microcontroller power-sequencing specification shown in figures 17 through 19 of the manufacturer datasheet. Typical applications include Power QUICC I and II microprocessor supplies, networking and telecom cards, DSP core and I/O rails, single-board computer point-of-load stages, and embedded computing platforms that need both a high-current switching rail and a quiet linear rail. When designing with this part, place the input bulk capacitors close to the PVCC pin and keep the bootstrap capacitor (BST to SW) trace short to minimize switching-node ringing. The exposed pad must be soldered to a sufficiently large copper pour to keep junction temperature within the SOIC-32 thermal limits at 3 A peak switch current. This page synthesizes distributor stock, parametric equivalents, and design notes not aggregated in any single manufacturer datasheet, helping procurement and design engineers evaluate MC34702EKR2 in context.

RFQ پەیوەندی
MC34703PNB - 10A Switch-Mode Power Supply IC with LDO | NXP
MC34703PNB

MC34703PNB - 10A Switch-Mode Power Supply IC with LDO | NXP

The NXP (formerly Freescale) MC34703PNB is a 10 A+ switch-mode power supply IC with an integrated LDO regulator, designed in a 33-pin PowerQFN (PQFN, 10 x 10 mm) package. It targets PowerQUICC and other high-current MCU/DSP core supplies, combining a high-performance synchronous buck switching regulator for the microprocessor core with auxiliary linear regulation for I/O or memory rails. The device operates from a 2.8 V to 13.5 V supply range and supplies approximately 60 mA to peripheral circuitry, supporting industrial -40C to +85C operation. A switch-mode power supply (SMPS) integrated into a Power Management IC (PMIC) is a high-efficiency DC-DC converter that uses pulse-width modulation (PWM), synchronous rectifiers and an LC output filter to step down a higher input rail to a lower, tightly regulated core voltage, while an integrated low-dropout linear regulator (LDO) provides a lower-current, low-noise post-regulation rail. Within the broader system hierarchy, the MC34703 sits above generic buck converters (it integrates two rails in one die) and below multi-channel PMICs that support full application processors. The integrated LDO plus switched core rail reduces the external component count compared to discrete two-rail solutions. Key features of the MC34703PNB include 10 A+ core switching capability, an integrated LDO regulator, programmable soft-start, power-good signaling, and enable inputs for power sequencing. The wide 2.8 V to 13.5 V input range allows direct operation from single-cell Li-ion packs as well as fixed 5 V, 9 V, and 12 V system rails without a pre-regulator. Synchronous rectification architecture delivers high conversion efficiency across typical loads, while the LDO cleans up post-regulation noise for I/O supplies. Typical applications include PowerQUICC and other high-end MCU/DSP core supplies, networking and telecom equipment requiring multi-rail power, industrial controllers with mixed-voltage cores, and embedded computing boards that benefit from integrated, compact power conversion. The combination of high-current switching plus LDO makes the device a single-chip solution for multi-rail microprocessor platforms. When designing with the MC34703PNB, ensure adequate PCB copper area for thermal dissipation (the 10 A core switch can dissipate multiple watts) and follow the manufacturer's recommended inductor and capacitor values closely, as the SMPS compensation network is tuned for those components. Decoupling should be placed directly at the package power and ground pins. This page synthesizes distributor pricing, package data, and design notes from the manufacturer datasheet to help engineers select, source, and apply the MC34703PNB with confidence.

RFQ پەیوەندی
MC34704AEP - Multi-Channel PMIC, 5/8 DC-DC, QFN-56 | NXP
MC34704AEP

MC34704AEP - Multi-Channel PMIC, 5/8 DC-DC, QFN-56 | NXP

The NXP MC34704AEP is a multi-channel Power Management IC (PMIC) that integrates up to 8 independent DC/DC switching regulators (or 5 channels plus pass transistors) in a single 56-pin QFN-EP (7x7 mm) package with exposed thermal pad. Operating from a 2.7 V to 5.5 V input rail, it is purpose-built to power multimedia application microprocessors from a single Li-Ion cell. A PMIC (Power Management Integrated Circuit) is a single-chip subsystem that consolidates multiple voltage rails - buck converters, LDOs, and pass elements - together with sequencing, voltage monitoring, and I2C/SPI control. Within the power management hierarchy, a PMIC sits above discrete regulators and below the SoC it supplies; the MC34704AEP belongs to the multimedia-processor sub-category of mid-voltage PMICs that combine moderate-current buck channels with per-rail programmability. Key features include 5 V to 0.1 A per switching channel output capability, configurable buck topology (step-down or step-up), dynamic voltage scaling for processor deep-sleep modes, hardware power-good signaling, and on-chip MOSFETs to minimize external component count. Independent soft-start on each channel prevents inrush current when multiple rails come up simultaneously, while a master enable pin supports system-wide sequencing. Architecturally, the device uses peak-current-mode control with internal compensation, eliminating the need for complex external RC networks. Each buck channel can deliver up to 0.1 A continuous with high efficiency across light and heavy loads. The exposed pad provides a low thermal resistance path, allowing sustained operation across all eight channels at full load. Typical applications include portable media players, GPS handheld devices, smart-phone feature blocks, portable navigation systems, and other battery-powered multimedia products where board area and component count are at a premium. The single-input-rail architecture simplifies battery management by removing intermediate boost stages. Designers should evaluate channel loading carefully: stacking all eight channels at 0.1 A produces 0.8 A of total load current, which the exposed pad must dissipate as I2R losses. Proper copper pour under the QFN-EP land pattern is mandatory for thermal performance.

RFQ پەیوەندی
MC34708VKR2 - PMIC for i.MX50/53, 6 Buck, 8 LDO | NXP
MC34708VKR2

MC34708VKR2 - PMIC for i.MX50/53, 6 Buck, 8 LDO | NXP

The NXP MC34708VKR2 is a highly integrated Power Management IC (PMIC) designed specifically for the NXP i.MX50 and i.MX53 processor families, providing 6 buck (switching) regulators, 8 LDOs, and a 10-bit ADC in a 206-ball MAPBGA (8x8 mm) package. It operates from a single 1.8V to 4.5V supply, typically a 3.7V lithium-ion battery, and integrates a battery charger and coin cell backup support for portable systems. A Power Management IC (PMIC) is a specialized power management device that integrates multiple voltage regulators, supervisory functions, and conversion circuits into a single chip. In the system hierarchy, a PMIC sits above individual DC-DC converters and LDOs, providing a complete multi-rail power solution that sequences, regulates, and monitors all supply rails required by an applications processor and its memory subsystem. Key features of the MC34708VKR2 include six buck converters that generate the core, memory, and I/O rails of the i.MX50/i.MX53 with high efficiency, eight LDOs for analog and low-noise rails, and a 10-bit ADC for battery voltage, current, and temperature monitoring. Switching regulators reduce power loss compared to linear-only solutions, which is critical for battery-operated multi-media devices. Integrated power sequencing and control via I2C allow the processor to reconfigure rails dynamically for power-save modes. Architecturally, the MC34708 implements multi-phase and single-phase buck topologies with programmable output voltages, and a charger block that manages USB or adapter input for single-cell Li-Ion batteries. The digital interface enables runtime voltage scaling, a feature heavily used by i.MX DVFS (Dynamic Voltage and Frequency Scaling) firmware. Typical applications include i.MX50/i.MX53-based tablet and e-reader designs, portable multimedia players, industrial HMI terminals, and embedded single-board computers requiring precisely sequenced multi-rail power. Note that NXP recommends the MMPF0100 or MC34709 for new designs, as the i.MX50/53 processors are mature and the MC34708 is in end-of-life status. Design consideration: verify that your software platform supports the MC34708 register map before hardware reuse; PMIC firmware dependencies often block direct substitution even when electrical parameters match. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
MCP16301T-E/CH - 30V 600mA Buck DC-DC Converter SOT-23-6 | Microchip
MCP16301T-E/CH

MCP16301T-E/CH - 30V 600mA Buck DC-DC Converter SOT-23-6 | Microchip

The Microchip MCP16301T-E/CH is a highly integrated, high-efficiency, fixed-frequency step-down DC-DC converter in a 6-pin SOT-23 package that operates from input voltage sources up to 30V. It delivers up to 600 mA of output current with adjustable output from 2V to 15V and is rated for automotive temperature grade. A buck converter (also called a step-down switching regulator) is a type of switched-mode power supply (SMPS) that efficiently converts a higher DC input voltage to a lower DC output voltage by periodically switching an integrated power transistor and storing energy in an external inductor. Buck converters sit within the broader hierarchy: DC-DC converter -> switched-mode power supply -> power management IC -> semiconductor. They are widely preferred over linear regulators when the input-to-output voltage differential is large, because their switching topology achieves 90%+ efficiency versus the 30-60% typical of an LDO dissipating the same drop. Key features include a 30V maximum input voltage rating, 600 mA continuous output current, integrated high-side N-channel MOSFET switch, fixed-frequency peak current-mode control, internal compensation, peak current limit, and overtemperature protection. The 6-pin SOT-23 footprint is one of the smallest packages available for a 30V-tolerant synchronous buck, making the part popular where PCB real estate is at a premium. The MCP16301T-E/CH uses peak current-mode control with internal compensation, eliminating the need for an external compensation network and reducing the BOM to typically four external components (input cap, output cap, inductor, feedback resistor divider). The internal switch is a high-side N-channel MOSFET rated to handle the 30V input transients common in 12V automotive and 24V industrial bus systems. The fixed switching frequency (typically 500 kHz) allows predictable EMI filter design. Typical applications include 12V automotive accessory rails, point-of-load (POL) conversion from 24V industrial buses, battery-powered portable equipment, distributed power in embedded systems, and as a compact local regulator after a higher-voltage bulk converter. The 2V to 15V adjustable output range covers the most common 3.3V, 5V, 9V, 12V and 15V system rails. When designing with this device, use a low-ESR ceramic input capacitor to handle the switching ripple, an inductor rated for at least 1.5x the peak switch current, and place the feedback resistors close to the FB pin to minimize noise pickup. The exposed pad (pin 6) must be soldered to a thermal copper pour for reliable operation above 200 mA loads. This page synthesizes distributor stock, current pricing, drop-in cross-brand alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, helping engineers select, source, and implement the MCP16301T-E/CH with confidence.

RFQ پەیوەندی
MGFS302405 - 30W 5V/6A Isolated DC-DC Module | Cosel
MGFS302405

MGFS302405 - 30W 5V/6A Isolated DC-DC Module | Cosel

The Cosel MGFS302405 is a 30 W isolated, board-mount DC-DC converter module that delivers a single 5 V output at up to 6 A from a wide 9 V to 36 V input range. Housed in a 6-pin through-hole package (DIP-style PCB mount) with industry-standard pinout, the part belongs to Cosel's MGFS30 family of encapsulated switching regulators designed for industrial, test-equipment, and embedded computing applications where a clean, isolated 5 V rail is required from a noisy 12 V or 24 V bus. An isolated module DC-DC converter is a complete, encapsulated switching power supply on a small PCB that takes a DC input, chops it at high frequency, runs it through a small transformer for galvanic isolation, then rectifies and filters the secondary to produce a clean, low-ripple DC output. The MGFS302405 sits in the DC-DC converter -> point-of-load (POL) module -> power management IC taxonomy, and it eliminates the need for the designer to design the transformer, control loop, and feedback compensation themselves. Key specifications include 5 V fixed output, 6 A continuous load current (30 W maximum), 9 V to 36 V DC input range (24 V nominal), 1500 V AC I/O isolation, and typical line/load regulation within +/-0.5%. Built-in protections include over-current, over-voltage, and over-temperature shutdown, and the unit operates across an industry-standard -40C to +85C ambient temperature range. The encapsulated six-pin through-hole package provides a robust mounting footprint suited to conventional PCB assembly and field-replaceable industrial designs. Internally, the MGFS302405 uses a single-ended forward converter topology with a planar transformer and primary-side regulation, delivering high efficiency (typically 87% at 24 V input, 5 V/6 A output) without requiring external heat sinking in most airflow conditions. The internal control IC and feedback loop are factory trimmed, eliminating design iteration and stabilizing BOM cost across production runs. Typical applications include factory automation PLCs, industrial sensor and actuator power, building-automation controllers, 24 V-bus distributed I/O, test-and-measurement instruments, and embedded SBCs requiring a regulated, isolated 5 V rail. The wide 9-36 V input accepts unregulated industrial supplies, battery-backed 12 V or 24 V systems, and automotive 24 V truck/bus rails. When designing with this module, observe Cosel's recommended input fuse and output capacitor values listed in the datasheet to keep ripple within spec and to ensure the safety-agency isolation ratings are preserved. Maintain the specified clearance and creepage distances around the package to retain the 1500 V AC isolation rating. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes that go beyond the manufacturer datasheet to help engineers evaluate, source, and design with the MGFS302405.

RFQ پەیوەندی
MGFS302405-G - 30W Isolated DC-DC 5V/6A Module | Cosel
MGFS302405-G

MGFS302405-G - 30W Isolated DC-DC 5V/6A Module | Cosel

The Cosel MGFS302405-G is a 30 W isolated board-mount DC-DC converter module delivering a regulated 5 V output at up to 6 A from a wide 9 V to 36 V input range, packaged in a through-hole 6-pin encapsulated brick with 1.5 kV DC isolation. It belongs to Cosel's MGFS30 family of compact, high-efficiency isolated point-of-load modules designed for industrial and ITE (commercial) applications where a clean, isolated 5 V rail is required from a noisy 12 V/24 V bus. An isolated DC-DC converter module is a self-contained power supply block that uses an internal transformer (galvanic barrier) to break the DC ground path between the source and load, providing safety isolation and noise immunity. Within the broader power-management hierarchy, a board-mount isolated module is a sub-category of DC-DC converters and switching regulators, sitting above discrete buck/boost converter designs in terms of integration level. The MGFS30 family targets the 15 W to 30 W tier where most industrial 5 V auxiliary rails operate. Key features of the MGFS302405-G include 30 W continuous output power, 6 A maximum output current, 90 % typical efficiency at nominal line, and a wide 9 V to 36 V input window that covers 12 V and 24 V industrial bus rails. The 1.5 kV DC input-to-output isolation satisfies reinforced-isolation requirements for industrial control and ITE equipment. The through-hole 6-pin brick package provides robust mechanical attachment and natural convection cooling up to the rated power. Internally the module uses a fixed-frequency isolated flyback-forward topology with synchronous rectification on the secondary, which explains the high 90 % efficiency at 24 V input. Integrated input filtering, soft-start, and over-current / over-temperature protection reduce the external component count to just input/output capacitors. The output voltage is factory-trimmed to 5 V ±2 %, eliminating the need for an external adjustment resistor. Typical applications include industrial PLC and sensor 5 V rails, factory automation I/O power, isolated 24 V-to-5 V bus converters, test-and-measurement front-end power, and ITE equipment requiring a regulated isolated 5 V supply. The wide 9 V to 36 V input allows a single part to cover both 12 V and 24 V nominal buses, simplifying BOM. When designing with this part, observe the derating curve above 60 °C and provide at least 2 mm clearance around the through-hole pins to meet the 1.5 kV isolation rating. A 22 µF input capacitor and a 100 µF output capacitor are recommended to suppress reflected ripple and load-step transients. Mount the module vertically on the PCB with the baseplate flush to maximize convection cooling. This page synthesizes distributor pricing, parametric drop-in alternatives, and applied design notes drawn from the Cosel MGFS series datasheet and authorized distributor data — content not aggregated on any single manufacturer or distributor page.

RFQ پەیوەندی
MIC2103YML - 75V 15A Adaptive On-Time Buck Controller | Microchip
MIC2103YML

MIC2103YML - 75V 15A Adaptive On-Time Buck Controller | Microchip

The Microchip Technology MIC2103YML is a 75 V, constant-frequency synchronous buck controller using adaptive on-time control, with a 4.5 V to 75 V input range and support for output currents up to 15 A. It is supplied in a 16-pin VQFN 3x3 mm package and provides one PWM switching output. A programmable switching range of 200 kHz to 600 kHz supports conversion from high-voltage industrial, telecom, and automotive-style buses to lower-voltage processor, networking, and test-equipment rails. A synchronous buck controller is a pulse-width-modulation controller for a step-down DC-DC converter. It drives a high-side switching MOSFET and a low-side synchronous rectifier rather than dissipating conversion energy in a linear element. The controller supplies gate-drive and timing functions, while external MOSFETs, inductors, capacitors, and feedback components determine practical power capability and loop performance. In the system hierarchy, the MIC2103 belongs to DC-DC converters, switching regulators, power-management ICs, and semiconductors. Key verified characteristics include a 75 V maximum supply, a 4.5 V minimum operating input, adjustable output down to 0.8 V, guaranteed output accuracy of ±1%, constant-frequency operation, adaptive on-time control, and a 200 kHz to 600 kHz programmable switching range. Hyper Light Load operation is identified by distributors and evaluation-board documentation. The controller supports up to 15 A output-current capability when paired with appropriately rated external power components; the IC itself does not carry 15 A continuously. The adaptive on-time architecture adapts high-side conduction time to operating conditions while retaining constant-frequency behavior. This architecture targets efficient conversion across a wide input range and reduces reliance on a fixed compensation approach. The controller is particularly relevant where a 48 V or higher bus must be reduced efficiently and where converter size, transition behavior, and external power-stage selection are central engineering constraints. Typical applications include telecom and networking power supplies, industrial 24 V or 48 V rails, server and data-center auxiliary supplies, instrumentation, and distributed power systems. The 75 V input rating provides design margin above common nominal 48 V buses, while the exposed thermal pad and compact 3x3 mm footprint support dense power-converter layouts. Design starts with selecting external MOSFETs whose voltage ratings, gate charges, and losses support the target rail and switching frequency. Follow the manufacturer datasheet for compensation, bootstrap components, gate-drive settings, current-limit implementation, and exposed-pad layout. Estimated converter dissipation must be calculated from actual MOSFET, inductor, and controller losses because the verified data does not provide a complete thermal-resistance table. This product page consolidates verified specifications, sourcing information, application guidance, and replacement limitations. No verified pin-compatible substitutes were established from the supplied cross-reference results, so the page avoids presenting unverified drop-in claims and distinguishes controller-only specifications from the external converter design.

RFQ پەیوەندی
MIC2103YML-TR - 75V Sync Buck Controller, Adaptive On-Time | Microchip
MIC2103YML-TR

MIC2103YML-TR - 75V Sync Buck Controller, Adaptive On-Time | Microchip

The Microchip MIC2103YML-TR is a 75V synchronous buck DC-DC controller featuring adaptive on-time control architecture, housed in a 16-pin VQFN (3x3 mm) package with an exposed pad. The device operates over an input supply range of 4.5V to 75V and supports output currents up to 15A when paired with external MOSFETs, with output voltage adjustable down to 0.8V at ±1% accuracy. A synchronous buck controller is a type of DC-DC switching converter that uses two MOSFETs (one high-side, one low-side) in a half-bridge topology to step down a higher input voltage to a lower regulated output voltage. Unlike an LDO (low-dropout linear regulator) that dissipates excess voltage as heat, a synchronous buck controller switches the MOSFETs at high frequency (typically 200kHz to 600kHz here) and uses an LC output filter to deliver a regulated rail with high efficiency - typically 90-95% - even at large input-to-output headroom. Within the broader hierarchy, MIC2103YML-TR sits as: buck controller -> DC-DC switching converter -> power management IC -> semiconductor. Its adaptive on-time control is a variant of voltage-mode hysteretic control that adjusts the on-pulse width in response to input/output voltage, eliminating the need for external loop compensation components. Key features include a 4.5V to 75V input voltage range (ideal for 12V, 24V, and 48V industrial buses), 200kHz to 600kHz programmable switching frequency, Hyper Light Load (HLL) operation for high efficiency at light loads, internal MOSFET drivers, programmable current limit, and ±1% output voltage accuracy. The 16-pin VQFN (3x3 mm) exposed-pad package reduces board space and provides a low thermal resistance path. Built-in protection includes input under-voltage lockout (UVLO), over-current protection (OCP), and thermal shutdown. The adaptive on-time architecture responds to line and load transients within one switching cycle without requiring compensation network tuning, simplifying design-in versus traditional peak current-mode controllers. HLL mode automatically transitions to a discontinuous conduction mode at light loads, preserving efficiency when the system is idling - critical for battery-powered and energy-harvesting applications. Typical applications include 24V industrial automation bus converters, 48V telecom point-of-load stages, automotive 12V battery accessory rails, battery-powered portable equipment, distributed power systems, and point-of-load regulation downstream of an isolated AC-DC or PFC stage. When designing with MIC2103YML-TR, choose external MOSFETs rated for the application's load current and drain-source voltage. A 2.2uH to 10uH inductor, 100nF bootstrap capacitor, and output ceramic capacitors are typical BOM components. Place the feedback resistors close to the FB pin to minimize noise pickup. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes - including adaptive on-time trade-offs and HLL efficiency curves - that are not consolidated on the manufacturer product page.

RFQ پەیوەندی
MIC2250YML-TR - 2A Low-EMI Boost Regulator | Microchip
MIC2250YML-TR

MIC2250YML-TR - 2A Low-EMI Boost Regulator | Microchip

The Microchip Technology MIC2250YML-TR is a general-purpose 2A boost (step-up) DC/DC switching regulator IC with integrated low-EMI dithering circuitry and an adjustable output voltage starting at 1.24V. It is housed in an 8-pin 2 mm x 2 mm MLF/VFDFN exposed-pad package and is supplied on tape-and-reel (TR) packaging for high-volume manufacturing. The part is optimized for noise-sensitive, hand-held, battery-powered applications where high efficiency across a wide load range is critical. A boost (step-up) DC/DC converter is a switching power supply topology that produces an output voltage higher than its input voltage. It is a member of the switching regulator family, itself a sub-category of power management ICs that convert one DC voltage level to another using energy storage (inductors and capacitors) and switching elements (MOSFETs). Boost regulators are widely used to derive system rails (e.g., 5V, 15V, or LED forward voltages) from a lower battery or bus voltage (e.g., Li-ion 3.7V, USB 5V, or 12V intermediate bus). Key features of the MIC2250YML-TR include a 2A internal switch rating, low EMI via dithered switching frequency to spread spectral energy, 1.2A continuous output current capability, high light-load efficiency, and a wide input voltage range suitable for single-cell Li-ion applications. The 8-MLF exposed pad provides a low thermal resistance path, enabling compact PCB layouts without external heatsinking. Architecturally, the MIC2250 uses a current-mode control loop with internal MOSFET and an external inductor/capacitor output filter. The dithering feature modulates the oscillator frequency to soften EMI peaks, simplifying EMC compliance for hand-held consumer and industrial products. Typical applications include OLED/LCD bias supplies, white-LED camera flash drivers, USB-powered boost rails, audio accessory power, and industrial sensor excitation. The 2A switch makes it well suited to loads up to 500 mA continuous from a single Li-ion cell. When designing with this device, choose an inductor with low DCR and a saturation rating of at least 3A to prevent saturation at peak switch current. Place the input/output ceramic capacitors as close as possible to the IC and use a ground plane under the exposed pad for thermal dissipation.

RFQ پەیوەندی