بەرهەمەکان (770+)

MPQ4420GJ-Z - 2A 36V Sync Buck Converter | Monolithic Power Systems
MPQ4420GJ-Z

MPQ4420GJ-Z - 2A 36V Sync Buck Converter | Monolithic Power Systems

The Monolithic Power Systems MPQ4420GJ-Z is a high-frequency, synchronous, rectified step-down switch-mode converter with built-in power MOSFETs, delivering 2 A continuous output current from a 4 V to 30 V input, with an adjustable output of 0.8 V to 27 V in an 8-pin TSOT23 (SOT-23-8 Thin) package. It operates at a 410 kHz switching frequency and is AEC-Q100 qualified for automotive use. A synchronous step-down (buck) converter is a type of DC-DC switching regulator that uses internal high-side and low-side MOSFETs instead of an external Schottky diode to step a higher input voltage down to a lower output voltage. Within the power management hierarchy, the buck converter sits under switching regulators, which themselves belong to the broader family of voltage regulators and power management ICs. Synchronous rectification improves efficiency, especially at light-to-medium loads. Key features include integrated power MOSFETs that minimize external component count, synchronous mode operation for higher efficiency across the full load range, current-mode control for fast transient response and easy loop stabilization, and a compact 8-pin TSOT23 footprint. Full protection features include over-current protection and thermal shutdown. Technically, the MPQ4420 uses current-mode architecture, which simplifies compensation and gives excellent load and line regulation over the wide 4 V to 30 V input supply range. The internal MOSFETs and 410 kHz switching frequency allow small inductors and capacitors, enabling very compact power solutions. The adjustable feedback pin supports output voltages from 0.8 V up to 27 V. Typical applications include automotive infotainment and auxiliary power rails, industrial 24 V bus point-of-load conversion, and distributed power systems in networking and telecom equipment where a wide input range and 2 A output are required. Design consideration: at 410 kHz, keep the SW node loop area small and place the input ceramic capacitor close to the IN and GND pins; verify thermal performance when running 2 A at high input-to-output differential. This page synthesizes distributor pricing context, drop-in alternatives, cross-reference data, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
NBM2317S60D1580T0R - 800W Non-Isolated Bus Converter 48V-to-12V | Vicor
NBM2317S60D1580T0R

NBM2317S60D1580T0R - 800W Non-Isolated Bus Converter 48V-to-12V | Vicor

The Vicor NBM2317S60D1580T0R is a high-efficiency non-isolated, fixed-ratio bidirectional bus converter operating from a 40 to 60 VDC high-side voltage bus to deliver a ratiometric low-side voltage from 10 to 15 VDC, with a continuous output power rating of 800 W and 97.9% peak efficiency. A bus converter (BCM, bus converter module) is a specialized DC-DC converter that uses a fixed turn ratio (rather than closed-loop PWM duty-cycle regulation) to step a high-voltage distribution bus down to a lower intermediate voltage, then feeds downstream point-of-load regulators. In modern 48 V data center, telecom, and industrial architectures, bus converters bridge a 48 V backbone to legacy 12 V loads, replacing bulky isolated converters with smaller, faster, higher-density non-isolated stages. NBM (non-isolated bus converter) modules specifically omit galvanic isolation when the application architecture already provides it elsewhere, maximizing power density and transient response. Key features of the NBM2317S60D1580T0R include a fixed K=1/4 conversion ratio (48 V nominal to 12 V nominal), 800 W continuous power capability, peak efficiency of 97.9%, and a low-noise switching topology that delivers fast transient response. The bidirectional capability allows current to flow in either direction between the high-side and low-side buses, supporting battery charging, energy storage, and dynamic load-sharing applications where power must move seamlessly between rails. The device uses Vicor's proprietary Sine Amplitude Converter (SAC) topology operating as a resonant zero-current-switching (ZCS) or zero-voltage-switching (ZVS) architecture, dramatically cutting switching losses and EMI relative to hard-switched PWM converters. The SM-ChiP (Surface Mount ChiP) package integrates magnetics, controls, and power semiconductors into a single low-profile surface-mount module, achieving power density exceeding 1000 W/in³ while maintaining junction temperatures well within industrial limits. Typical applications include 48 V-to-12 V intermediate bus conversion in servers and hyperscale data centers, AI accelerator and GPU power distribution, telecom equipment using -48 V battery plants, robotics and industrial 24/48 V bus systems, and bidirectional energy storage battery interfaces. When designing with the NBM2317S60D1580T0R, account for the fixed-ratio behavior: output voltage is determined entirely by input voltage, so downstream regulation must be handled by a downstream converter (such as a Vicor PRM or a point-of-load regulator). Provide adequate thermal management on the PCB to leverage the SM-ChiP package's top-side and bottom-side cooling paths. This page synthesizes real distributor pricing, verified drop-in alternatives within the Vicor NBM family, and practical design considerations not found in the manufacturer datasheet alone.

RFQ پەیوەندی
NBM2317S60D1580TMR - 1080W Non-Isolated Bus Converter | Vicor
NBM2317S60D1580TMR

NBM2317S60D1580TMR - 1080W Non-Isolated Bus Converter | Vicor

The Vicor NBM2317S60D1580TMR is a high-efficiency non-isolated bus converter module designed to bridge 48V and 12V power-system domains. It operates from a 40V to 60V high-side input and delivers a ratiometric low-side output of 10V to 15V at up to 80A (1080W peak), with 97.9% peak efficiency. The SMD variant uses Vicor's 2317 Chameleon package with surface-mount termination for high-density PCB assembly. What is a non-isolated bus converter? A non-isolated bus converter (NIBC) is a fixed-ratio DC-DC converter used as a virtual supply rail in distributed power architectures. Unlike a switching regulator, an NIBC divides an existing high-voltage bus into a lower-voltage sub-rail using a capacitive energy-transfer topology. NIBC sits in the power-converter hierarchy as a category between point-of-load regulators and isolated DC-DC converters, providing high step-down ratios without transformer isolation. Key features of the NBM2317S60D1580TMR include a continuous 800W power rating, fixed 4:1 conversion ratio, 1.4 MHz switching frequency, parallelable operation for higher power, and bi-directional power flow capability. Typical conversion efficiency reaches 97.9% at nominal 48V/12V operation, reducing thermal losses compared to traditional buck converters at the same current rating. The NBM family from Vicor uses a proprietary Sinusoidal Amplitude Converter (SAC) topology combined with a zero-voltage, zero-current switching (ZVZCS) soft-switching architecture. This topology achieves high efficiency by eliminating switching losses and uses small ceramic bypass capacitors instead of bulky inductors or transformers. The result is a low-profile surface-mount module that fits between a 48V intermediate bus and downstream 12V point-of-load converters or direct loads. Typical applications include 12V intermediate bus generation in 48V telecom and data-center servers, AI accelerator and GPU auxiliary rails, high-current 12V distribution in industrial equipment, battery energy storage systems using 48V architecture, and bridging converters for automotive 48V mild-hybrid systems. When designing with this part, account for the fixed 4:1 conversion ratio: VOUT follows VIN/4 with a tolerance band. Use the module in conjunction with downstream buck or ZVS regulators for sub-ratios (5V, 3.3V, 1V). Provide adequate PCB copper beneath the surface-mount land pattern for thermal dissipation and high-current return paths. This page synthesizes distributor pricing, drop-in module equivalents, and paralleling notes not found in the manufacturer datasheet.

RFQ پەیوەندی
NBM2317S60E1560T0R - 800W Non-Isolated Bus Converter 60A | Vicor
NBM2317S60E1560T0R

NBM2317S60E1560T0R - 800W Non-Isolated Bus Converter 60A | Vicor

The Vicor NBM2317S60E1560T0R is a 800 W Non-Isolated Bus Converter Module operating from a 38 V to 60 VDC high-side bus to deliver a ratiometric low-side voltage of 9.5 V to 15 VDC at up to 60 A continuous current, housed in a surface-mount ChiP (Chip-in-Plastic) package. It achieves 97.9% peak efficiency, up to 4.5 kW/in³ power density, and provides bidirectional start-up and steady-state operation with up to 1 kW, 2 ms peak power capability. A bus converter (also called a Bus Converter Module, BCM or NBM in Vicor nomenclature) is a fixed-ratio, non-isolated DC-DC converter that steps a higher distribution voltage down by a deterministic factor (in this case K=1/4 approx, 38-60V -> 9.5-15V) to power downstream point-of-load (PoL) regulators. Unlike a discrete buck regulator, the bus converter uses a Sine Amplitude Converter (SAC) topology with a proprietary zero-voltage-switching (ZVS) / zero-current-switching (ZCS) architecture, achieving high density and low noise. In a system hierarchy it sits above PoL regulators (DCM, PRM, PoL converters) and is part of the Factorized Power Architecture (FPA) ecosystem from Vicor. Key features include 60 A rated output current (step-down operation), 38-60 V high-side input range, a 9.5-15 V ratiometric low-side output, and 97.9% peak efficiency. The module provides low output impedance well beyond the bandwidth of most downstream PoL regulators, meaning input capacitance that would normally sit at the PoL input can be moved to the high-voltage side, reducing PCB area and BOM count. Technically, the NBM2317S60E1560T0R uses Vicor's proprietary SAC topology with a high-frequency soft-switching architecture achieving >97% efficiency at typical loads. The part is bidirectional, capable of start-up and steady-state operation in either direction when used with Vicor's PRM or BCM companion parts. Two cooling configurations are supported: two-sided cooling and bottom-side only (through-PCB) cooling, with thermal models provided for each. Typical applications include 48 V data center and telecom intermediate bus conversion, distributed power architectures for AI accelerators and GPUs, high-end computing motherboards, industrial 48 V robotics, and aerospace distributed power systems. The bidirectional capability makes it suitable for energy storage and battery systems as well. When designing with this device, ensure adequate PCB copper thermal mass or attach to a cold plate. Use Vicor's companion evaluation boards for thermal characterization and consult the datasheet for derating curves beyond the 60 A continuous rating. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison data, and practical design guidance not assembled on any single manufacturer or distributor page.

RFQ پەیوەندی
NBM2317S60E1560T0R-VICOR - 800W Non-Isolated Bus Converter | Vicor
NBM2317S60E1560T0R-VICOR

NBM2317S60E1560T0R-VICOR - 800W Non-Isolated Bus Converter | Vicor

The Vicor NBM2317S60E1560T0R is a non-isolated, fixed-ratio DC-DC bus converter module (BCM) using Vicor's proprietary Sine Amplitude Converter (SAC) topology, delivering up to 800 W of continuous output power from a 38 V to 60 V input range to a ratiometric 13.5 V output at 60 A, in a surface-mount Chip (ChiP) package. It achieves a peak efficiency of 97.9 percent at moderate loading and supports bidirectional start-up and steady-state operation, enabling battery-source and bus-source flexibility. A bus converter module (BCM) is a fixed-ratio, non-isolated DC-DC converter that divides an intermediate bus voltage by a fixed K-factor (turns ratio equivalent) to produce a lower, regulated-feeling output. BCMs sit between an isolated front-end converter and downstream point-of-load (PoL) regulators, providing a low-impedance intermediate voltage rail with fast transient response and high efficiency. As fixed-ratio devices, BCMs cannot regulate output voltage independently of input voltage - regulation is achieved by the upstream front-end converter and downstream PoL stages, while the BCM provides the power transformation with minimal loss. Key features include a fixed K-factor of 1/4, a sinusoidal SAC switching waveform that minimises EMI and acoustic noise, low AC impedance beyond the bandwidth of typical PoL regulators, and up to 4.5 kW per cubic inch power density. The device supports up to 1 kW peak output for 2 ms transient events, an integrated thermal management footprint accepting either two-sided or bottom-side PCB cooling, and parallel operation capability for higher power rails. The ChiP surface-mount form factor eliminates through-hole magnetics and shrinks the converter footprint by an order of magnitude compared with discrete bus-converter designs. The NBM2317S60E1560T0R uses a zero-voltage switching (ZVS), zero-current switching (ZCS) Sine Amplitude Converter architecture operating at a fixed fundamental frequency in the megahertz range. The fixed K-factor of 1/4 means any input from 38 V to 60 V produces an output of 9.5 V to 15 V (Vin/4); the stated nominal output is 13.5 V at the typical 54 V nominal input. The bidirectional capability allows the same module to operate as a step-down or step-up converter, supporting battery charging and energy-storage applications without a second power path. Typical applications include 48 V telecommunications intermediate bus architectures, blade-server and high-performance compute power delivery, battery-backed 48 V infrastructure, industrial automation systems with 48 V or 54 V distribution, and high-current PoL rails where upstream isolation is handled separately. Designers commonly cascade this BCM with downstream PRM (pre-regulation) and VTM (voltage transformation) Vicor components, or with a family of point-of-load regulators from the same Vicor ecosystem. When designing with this device, ensure that input voltage remains within the 38 V to 60 V window under all line and load transients, and that the upstream source can absorb reflected ripple current from the BCM. The ChiP solder-pad layout is not compatible with hand-soldered or socketed assemblies - it requires a reflow profile aligned with the J-STD-020 MSL rating for the part. This page synthesises distributor pricing, drop-in same-family alternatives, and practical thermal-layout notes that are not gathered in any single manufacturer datasheet, giving engineers a faster path to a verified BOM decision.

RFQ پەیوەندی
NCL2801CDADR2G - High-Efficiency CrM Boost PFC Controller
NCL2801CDADR2G

NCL2801CDADR2G - High-Efficiency CrM Boost PFC Controller

The onsemi NCL2801CDADR2G is a high-efficiency current-mode critical-conduction-mode boost power-factor correction controller packaged in an 8-pin SOIC. It is designed for LED-lighting power supplies and other AC-DC boost PFC stages handling substantial bulk-capacitor ripple. Its headline features are current-mode CrM control, enhanced line-current total harmonic distortion performance, Valley Count Frequency Fold-back operation, and a 12.5 V start voltage. A power-factor controller is an integrated circuit that shapes input current drawn from an AC mains line so that current tracks voltage and the upstream system approaches unity power factor. In the broader hierarchy, the NCL2801 belongs to AC-DC power conversion, power management integrated circuits, and boost PFC controllers. Correct operation reduces reactive current, line-current distortion, and stress in upstream magnetic and capacitor components. The NCL2801 uses THD Enhancer technology to improve line-current total harmonic distortion across an extended operating range. It operates classically in Critical Conduction Mode at high loads. When load decreases, Valley Count Frequency Fold-back forces discontinuous conduction by introducing dead time corresponding to a fixed number of valleys, improving standby behavior while maintaining regulation. The 8-SOIC package supports compact offline-lighting designs. The controller is intended to drive PFC boost stages rather than directly switching the mains-connected power stage. A typical implementation combines the NCL2801 with a boost inductor, switching MOSFET, current-sense resistor, bridge rectifier, bulk capacitor, safety-rated components, and LED-driver downstream circuitry. The controller supplies control and protection functions, while the external power components determine available output power and conversion ratio. Typical applications include LED lamps and luminaires, electronic ballasts, compact offline LED power supplies, and cost-effective high-efficiency AC-DC front ends. The device is especially useful where low line-current THD, low standby power, and tolerance of high ripple on the bulk capacitor are important. Its lighting-focused feature set helps designers meet EMI and input-current-shape requirements without relying on a more complex digital controller. Design the feedback network and compensation for the actual boost converter, not as a generic voltage-regulator stage. Keep the current-sense loop short, isolate high-voltage switching nodes from sensitive control traces, and follow the manufacturer's application guidance for layout and component values. Review the datasheet limits before selecting the MOSFET, inductor, capacitor, and safety components. This page combines the verified manufacturer description, package and distributor information, application guidance, and engineering-oriented replacement limitations. It does not infer unprovided electrical limits or claim a pin-compatible replacement when the available cross-reference results do not establish one.

RFQ پەیوەندی
NCP1294 - Fixed Frequency PWM Controller for Flyback/Forward/Boost | onsemi
NCP1294

NCP1294 - Fixed Frequency PWM Controller for Flyback/Forward/Boost | onsemi

The onsemi NCP1294 is a fixed frequency, feed forward voltage mode PWM controller optimized for high frequency primary side control in Flyback, Forward, or Boost converter topologies. It integrates a complete set of control features including soft start, accurate duty cycle limit, less than 50 uA startup current, and dedicated over and under voltage protection. The device operates from a VCC supply commonly fed via an auxiliary winding, and it drives an external MOSFET through a totem pole output stage sized for direct gate drive in low to medium power converters. A PWM controller is a building block inside switched mode power supplies (SMPS) that produces a fixed frequency clock and modulates its duty cycle to regulate the converter output voltage. In the hierarchy of power management ICs, the NCP1294 sits as a current mode/peak control sub-family member: PWM controller -> SMPS controller -> DC-DC controller -> power management IC -> semiconductor. Its feed forward voltage mode architecture adds line-voltage feed forward to reject input voltage transients faster than a conventional voltage mode controller can respond through its error amplifier loop alone. Key features include programmable maximum duty cycle clamp, cycle-by-cycle current limit, internal soft start, undervoltage lockout, overvoltage protection, and a low startup current below 50 uA which simplifies self bias designs from the input bulk rail. The controller typically operates at switching frequencies programmable up to the audio band and beyond, enabling smaller magnetics in isolated telecom and industrial auxiliary supplies. The architecture uses a leading edge blanking interval to mask the leading edge current spike caused by the MOSFET turn on transient, improving noise immunity at the current sense input. Internally the oscillator is trimmed and the reference is bandgap based for stable operation over temperature, supporting industrial operating ranges typical of -40C to +125C. The combined UVLO and OVP set the input supply window for the IC itself, simplifying the housekeeping design on the primary side. Typical applications for the NCP1294 include isolated telecom auxiliary supplies such as 48 V to low voltage DC-DC bricks, industrial DIN rail and process control power modules, AC-DC adapters up to several hundred watts using forward or flyback topologies, and standby/auxiliary rails in server and PoE powered systems. Its configuration flexibility also suits it for boost derived front end PFC auxiliary rails and small solar micro inverter auxiliary supplies. When designing with the NCP1294, pay close attention to current sense resistor placement and to the CS pin filter network, because the leading edge blanking only masks the first few hundred nanoseconds of the turn on spike; longer ringing from a poor layout will inject false current limit triggers. Use a small RC on the CS pin and keep the sense loop area minimal. This page consolidates onsemi datasheet parameters, distributor stock pricing, and same-package drop-in alternatives such as the NCP1294C and NCP1284 into a single engineering reference so that sourcing, replacement, and design decisions can be made without cross referencing multiple distributor and manufacturer PDFs.

RFQ پەیوەندی
NCP1294DB - Fixed-Frequency PWM Controller | onsemi
NCP1294DB

NCP1294DB - Fixed-Frequency PWM Controller | onsemi

The onsemi NCP1294DB is a fixed-frequency, feed-forward, voltage-mode PWM controller optimized for high-frequency primary-side control. It supports basic flyback, boost, and forward-converter topologies, operates from the DC input rail supplying the primary circuit, and is packaged for surface-mount assembly. The verified manufacturer material specifically identifies soft-start, accurate duty-cycle limiting, less than 50 uA startup current, overvoltage and undervoltage protection, and current-mode operation as key features. A PWM controller is a semiconductor timing and regulation device used in switched-mode power supplies. Its oscillator establishes the switching frequency, while its control loop compares a feedback signal with an internal reference and adjusts the gate-drive command. The NCP1294DB belongs to the DC-DC power-conversion controller category and is intended for isolated flyback or forward designs as well as non-isolated boost arrangements. Feed-forward voltage-mode control is especially relevant to offline power-conversion systems where predictable duty-cycle behavior and primary-side regulation are important. The controller’s fixed-frequency architecture simplifies compensation planning because the nominal switching point does not vary with input voltage. Soft-start helps limit inrush stress during power-up, while accurate duty-cycle limiting constrains the maximum commanded on-time. The low startup current is intended to reduce the burden on the startup path before the auxiliary supply becomes operational. Overvoltage and undervoltage protection provide additional system safeguards, although exact thresholds, tolerances, response timing, and restart behavior must be taken directly from the manufacturer datasheet. The NCP1294 is designed for high-frequency primary-side control, making it relevant to compact AC/DC adapters, offline power supplies, forward converters, boost converters, and industrial control systems. In an isolated flyback design, the controller drives a primary MOSFET while an optocoupler or other isolation mechanism communicates output-voltage information. In a forward converter, transformer reset and duty-cycle constraints determine the practical power level. In a boost design, the same controller family supports a non-isolated conversion stage when its voltage and timing limits are satisfied. Designers should use the datasheet’s recommended oscillator, compensation, current-sense, startup, and gate-drive networks rather than treating generic PWM-controller layouts as directly interchangeable. Transformer reset time, propagation delay, MOSFET switching speed, output-capacitor ESR, feedback bandwidth, and safety spacing all affect practical performance. NCP1294DB is a controller, not a complete power stage; an external MOSFET, magnetics, rectifier, feedback network, and protection components remain necessary. This page summarizes the verified NCP1294DB architecture, application fit, and design considerations while distinguishing documented features from parameters that were not supplied in the retrieved source text. For sourcing, confirmation of current lifecycle and exact package-related ordering details should be completed before committing a production design.

RFQ پەیوەندی
NCP1399APDR2G - 600V Half-Bridge Resonant Controller | onsemi
NCP1399APDR2G

NCP1399APDR2G - 600V Half-Bridge Resonant Controller | onsemi

The onsemi NCP1399APDR2G is a high-performance current mode controller for half-bridge resonant converters, integrating two 600 V gate drivers in a 16-pin SOIC package. It supports a wide switching frequency range of 20 kHz to 750 kHz, adaptive dead-time control, and a dedicated PFC front-stage interface, making it well-suited for high-efficiency LLC and other resonant converter topologies. An LLC resonant controller is a specialized power-supply control IC that drives a half-bridge switching stage whose switches feed an LC resonant tank. The tank shapes the current waveform so the MOSFETs switch at zero voltage (ZVS), eliminating switching losses and enabling high-frequency, high-density designs. Controllers such as the NCP1399APDR2G sit within the power-management IC family and are commonly deployed as the secondary-side controller after a PFC front end in TV power supplies, server PSUs, and industrial SMPS modules. Key features of the NCP1399APDR2G include integrated 600 V half-bridge gate drivers that simplify PCB layout and reduce the bill of materials, an adjustable minimum switching frequency with precise dead-time generation, dedicated PFC control output for coordinated front-stage operation, brown-out protection on the high-voltage bulk rail, and comprehensive fault protection (overcurrent, overtemperature, overload, and brown-out). According to the onsemi NCP1399 datasheet, the device also features a skip-mode function for light-load efficiency improvement. Architecturally, the NCP1399APDR2G uses a current-mode control loop with a dedicated feedback input, allowing tight regulation of the resonant tank current. The adaptive dead-time block automatically adjusts the dead time between the high-side and low-side gate drive transitions to minimize body-diode conduction and maximize the ZVS range. The 600 V high-side driver is implemented using a level-shifter with an internal bootstrap clamp, removing the need for an external bootstrap diode in many designs. Typical applications include LCD TV power supplies (>150 W), notebook and laptop adapters, server and telecom SMPS modules, industrial LED drivers, and any high-density isolated DC-DC converter requiring ZVS operation above 100 W. The dedicated PFC output makes it an ideal match for designs requiring energy compliance such as 80 PLUS or ENERGY STAR. When designing with the NCP1399APDR2G, ensure the high-voltage bulk rail is decoupled with at least 1 µF X7R close to the Vbulk pin and follow the PCB layout guidelines for the high-side driver return path. The integrated 600 V drivers eliminate the need for an external gate-drive transformer, but the bootstrap capacitor must be sized correctly for the switching frequency and gate charge of the chosen MOSFETs. This page synthesizes distributor pricing, drop-in alternative recommendations, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
NCP1654BD133R2G - 133 kHz CCM PFC Controller | onsemi
NCP1654BD133R2G

NCP1654BD133R2G - 133 kHz CCM PFC Controller | onsemi

The onsemi NCP1654BD133R2G is a continuous-conduction-mode power factor correction controller with a nominal 133 kHz switching frequency in an 8-pin SOIC package. It is designed to control the power-switch conduction time in fixed-frequency PWM operation using instantaneous inductor-current feedback. The verified distributor listing specifies a 120 kHz to 146 kHz operating range. This controller belongs to the power-factor-correction and AC-DC power-conversion hierarchy, where it helps shape input current and reduce reactive power in boost pre-converter stages. A power factor correction controller is an integrated control IC that regulates the duty cycle and timing of a boost-converter power switch. In a CCM PFC stage, the inductor remains conducting during each switching cycle, and the controller adjusts switch timing from measured current to support near-unity power factor while transferring energy toward the DC output bus. The NCP1654 is intended for compact and robust continuous-conduction-mode step-up pre-converters. The main verified features of NCP1654BD133R2G are its CCM PFC architecture, fixed-frequency PWM operation, 133 kHz nominal switching frequency, 120 kHz to 146 kHz distributor-listed frequency range, and SOIC-8 package. The onsemi product page describes the family as minimizing external components and simplifying PFC implementation. The package and low component count can help reduce board area, but the final design still requires careful validation of inductor selection, current sensing, protection, startup behavior, and mains-side isolation. Its switching frequency affects magnetic-component size, control-loop behavior, switching losses, and electromagnetic-interference requirements. A 133 kHz nominal frequency is generally positioned above low-frequency boost operation for compactness and lower inductor size, but it does not eliminate the need for layout and thermal checks. The controller’s fixed-frequency operation should be compared with the power stage’s maximum switching stress and the inductor ripple-current target during design review. Typical applications include compact server and telecom power supplies, industrial AC-DC front ends, charger front ends, power adapters, and other boost PFC stages operating from rectified AC. The part is appropriate when the design needs a dedicated CCM PFC controller rather than a generic PWM regulator. Its external power switch and passive components must be selected for the actual input voltage, output voltage, output power, switching frequency, and thermal environment. For implementation, place the controller, current-sense network, gate-drive components, and power-stage connections according to the manufacturer datasheet layout guidance. Maintain short high-current switching loops, provide appropriate input and output decoupling, and verify creepage and clearance for the mains-connected front end. Do not treat the distributor frequency snippet as a substitute for the complete electrical limits; missing values should be confirmed in the manufacturer datasheet. This page combines the verified manufacturer description, distributor identity and package information, and practical selection guidance for engineers evaluating the NCP1654 family. It also distinguishes verified facts from parameters that still require datasheet confirmation, helping procurement and design teams make a more reliable decision for compact CCM PFC pre-converters.

RFQ پەیوەندی
NCP3063B - 1.5A Step-Up/Down/Inverting Switching Regulator | onsemi
NCP3063B

NCP3063B - 1.5A Step-Up/Down/Inverting Switching Regulator | onsemi

The onsemi NCP3063B is a monolithic 1.5 A DC-DC switching regulator supporting step-up, step-down, and voltage-inverting topologies in a single IC. Housed in an 8-SOIC package, it integrates a temperature-compensated reference, a duty-cycle controlled oscillator with active current limit, a high-current output switch, and an internal thermal shutdown circuit. The device is a higher-frequency upgrade to the legacy MC34063A / MC33063A family. A switching regulator (sometimes called a SMPS controller or DC-DC converter IC) is a power management device that uses an internal power switch and an external inductor/capacitor network to efficiently convert one DC voltage to another. Switching regulators sit within the power management IC category, between linear regulators (which dissipate excess voltage as heat) and fully modular DC-DC converter modules. They are typically selected when efficiency, output current, or output voltage flexibility are paramount. The NCP3063 specifically targets low-cost step-up, step-down, and inverting converter implementations. The NCP3063B delivers 1.5 A peak switch current with an adjustable output voltage of 1.25 V and supports a wide operating voltage range suitable for single-cell to multi-cell battery inputs. It includes cycle-by-cycle current limiting, internal thermal shutdown, and a duty cycle controlled oscillator. The 8-SOIC surface-mount package provides a compact footprint with standard pin compatibility with the older MC34063A. Architecturally, the device uses a current-mode control loop with a 1.25 V internal reference and an external feedback divider. The oscillator frequency is set by a single timing capacitor, allowing designers to optimize efficiency versus component size. An internal comparator drives a Darlington output stage capable of sinking or sourcing up to 1.5 A peak. Cycle-by-cycle current limit is implemented by sensing the switch emitter voltage against an internal reference. Typical applications include cost-sensitive consumer products, battery-powered portable equipment, LED drivers, and auxiliary supplies in industrial systems. It is particularly attractive as a drop-in upgrade for legacy MC34063A designs where higher switching frequency allows smaller inductors and capacitors. The wide input tolerance also makes it suitable for automotive subsystems running off 12 V or 24 V rails. When designing with the NCP3063B, carefully size the inductor and flyback capacitor to maintain continuous conduction at the minimum load. The thermal pad of the 8-SOIC should be soldered to a copper pour for adequate heat dissipation at high switch currents. Always verify that the peak switch current does not exceed 1.5 A under worst-case conditions. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found on a single distributor or manufacturer page, with all data points cited to either the onsemi datasheet (document NCP3063-D) or the listed data sources.

RFQ پەیوەندی
NCP3135MNTXG - 5A Sync Buck Converter 2.9-5.5V | onsemi
NCP3135MNTXG

NCP3135MNTXG - 5A Sync Buck Converter 2.9-5.5V | onsemi

The onsemi NCP3135MNTXG is a fully integrated synchronous buck converter delivering up to 5 A continuous DC load current (6 A instantaneous) from a 2.9 V to 5.5 V input rail, housed in a 16-pin VFQFN exposed-pad (QFN-16 EP) package. It targets 3.3 V and 5 V step-down applications with an adjustable output from 0.6 V to 4.62 V and supports two control modes (FCCM and automatic CCM/DCM) for efficiency-versus-ripple tuning. Integrated high-side and low-side MOSFETs, internal compensation, and a power-good indicator minimize external component count and PCB area. A buck (step-down) DC-DC switching converter is a power management IC that efficiently converts a higher DC input voltage to a lower regulated DC output voltage by rapidly switching an internal MOSFET and smoothing the resulting pulsed waveform through an LC filter. Within the power management hierarchy, it sits above linear regulators (LDOs) in efficiency for large VIN/VOUT deltas but below multi-phase VRMs in current capability. Buck converters are the workhorse topology for distributing intermediate bus voltages (5 V, 3.3 V, 1.8 V, 1.2 V) across nearly every digital and mixed-signal system. The NCP3135MNTXG delivers 5 A continuous / 6 A peak output, operates from 2.9 V to 5.5 V VIN, and adjusts VOUT from 0.6 V to roughly VIN minus dropout. Its selectable FCCM (forced continuous conduction mode) ensures predictable noise/ripple regardless of load, while automatic CCM/DCM mode boosts light-load efficiency by skipping pulses. Internal MOSFETs (high-side + low-side) eliminate external FET selection, and built-in soft-start, power-good, and over-current/thermal protection reduce design risk. The 16-pin QFN exposed pad provides a low thermal resistance path, simplifying board-level thermal management. The architecture uses adaptive on-time (AOT) control with internal feedback compensation, enabling fast transient response without requiring external RC networks. The 5 V tolerant enable pin and power-good output simplify sequencing in multi-rail systems. By integrating both switches and compensation, the NCP3135 family targets designs where small PCB footprint, high efficiency, and minimal external BOM are critical. Typical applications include 5 V and 3.3 V point-of-load regulation in networking switches, FPGA/CPLD core and I/O rails, SSD controller power, set-top box and consumer SoC rails, and distributed bus converters in telecom/datacom cards. It is well suited wherever a single 5 V input must be stepped down to a lower logic rail with high efficiency and tight load regulation. When designing with this device, derate output current based on VIN/VOUT differential and ambient temperature. Ensure the exposed pad is soldered to a sufficient copper pour to keep junction temperature within the SOA. Select input/output ceramic capacitors with low ESR and adequate voltage derating; place the input cap as close as possible to the VIN and GND pins to minimize switching-node ringing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet alone.

RFQ پەیوەندی
NCP3170BDR2G - 3A 18V Sync PWM Buck Converter SOIC-8 | onsemi
NCP3170BDR2G

NCP3170BDR2G - 3A 18V Sync PWM Buck Converter SOIC-8 | onsemi

The onsemi NCP3170BDR2G is a 3 A synchronous PWM buck (step-down) DC-DC switching regulator operating from 4.5 V to 18 V input and producing adjustable outputs as low as 0.8 V in an 8-pin SOIC (0.154", 3.90 mm width) surface-mount package. It integrates the high-side and low-side MOSFETs to deliver up to 3 A continuous load current at switching frequencies up to 1 MHz, while providing cycle-by-cycle current-mode control for fast transient response and inherent line-voltage feed-forward. A buck (step-down) switching regulator is a type of DC-DC converter that efficiently steps a higher input voltage down to a lower output voltage by rapidly switching an internal power transistor and storing it in an external inductor. It belongs to the broader hierarchy of switched-mode power supplies (SMPS), which also includes boost, buck-boost, and SEPIC topologies. SMPS ICs in turn belong to the power management IC family used to generate stable, efficient rails for downstream analog and digital ICs. Key differentiating features include an internal 0.8 V ±2% reference, internal soft-start, power-good (PG) open-drain output, and internal compensation that minimizes external part count. The NCP3170 family (suffixes A and B) offers 3 A continuous output current, fixed-frequency PWM control for low noise, and a thermal-shutdown protection scheme. The B suffix (NCP3170B) is the 1 MHz switching-frequency option optimized for smaller inductors and capacitors. The architecture is a peak current-mode controller with internal synchronous rectification, eliminating the need for an external Schottky diode. The high-side P-MOSFET (upper switch) and low-side N-MOSFET (lower switch) are integrated, which reduces board area, lowers BOM cost, and improves efficiency at light loads. Cycle-by-cycle current sensing on the high-side MOSFET provides fast overcurrent protection and inherent input voltage feed-forward for good line transient rejection. Typical applications include point-of-load (POL) converters for FPGAs, ASICs, and DSPs, distributed 5 V/12 V bus regulation, networking and telecom card supplies, industrial control and factory-automation boards, and consumer set-top boxes. The 18 V input rating suits 12 V and 15 V rails common in distributed-power architectures. When designing with this part, select the external inductor using the datasheet's L = VOUT / (IOUT × fSW × ΔIL) guideline (e.g., approximately 4.7 µH at 5 VOUT, 1 MHz). Place input/output ceramic capacitors close to the IC and use a star-ground scheme; routing the exposed pad (when present) to a large ground copper pour improves thermal dissipation at full 3 A load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
NCP3231AMNTXG - 25A Synchronous Buck Converter, 4.5-18V | onsemi
NCP3231AMNTXG

NCP3231AMNTXG - 25A Synchronous Buck Converter, 4.5-18V | onsemi

The onsemi NCP3231AMNTXG is a high-current, high-efficiency voltage-mode synchronous buck converter that operates from a 4.5 V to 18 V input rail and delivers output voltages as low as 0.6 V at up to 25 A continuous load current, packaged in a 40-pin VFQFN with exposed thermal pad. A buck converter (step-down DC-DC converter) is a switch-mode power supply topology that efficiently converts a higher DC input voltage to a lower DC output voltage by rapidly switching an inductor between charge and discharge phases. Within the broader taxonomy, the NCP3231AMNTXG belongs to the synchronous buck family (where a MOSFET replaces the conventional rectifier diode for higher efficiency), inside the voltage-mode PWM controller category, inside DC-DC switching regulators, inside the power management IC segment of integrated semiconductors. Key specifications include a 4.5 V to 18 V input range, adjustable output from 0.6 V up to roughly 5 V (limited by the 18 V maximum input minus headroom), 25 A continuous output current, and a high-side low-side integrated MOSFET pair that delivers high efficiency without external switches. The 40-pin VFQFN package with an exposed thermal pad supports sustained high-current operation by providing a low thermal-resistance path to PCB copper. The NCP3231A employs voltage-mode control with internal compensation, programmable switching frequency, soft-start, and comprehensive protection features including over-current, over-voltage, under-voltage lockout, and thermal shutdown. The synchronous rectification architecture eliminates the conduction loss of a freewheeling diode and pushes typical full-load efficiency above 90 percent at 12 V input to 1.2 V output, a level that conventional buck controllers cannot match without discrete synchronous FETs. Typical applications include server and telecom point-of-load converters, networking switch and router core rails, FPGA and ASIC power rails, industrial 12 V intermediate bus converters, and high-current distributed DC-DC POL modules. The 25 A capability is well suited to powering multi-core processors, DDR memory banks, and high-performance DSPs directly from a 12 V bus. When designing with this part, allocate substantial PCB copper area beneath the exposed pad to keep junction temperature within the safe operating area at 25 A, and follow the manufacturer's recommended input/output inductor and capacitor selection for the chosen switching frequency. Use the soft-start and enable pins to sequence multiple NCP3231AMNTXG rails in a multi-rail system. This page synthesizes distributor pricing, drop-in same-brand variants, and practical design notes that consolidate information normally scattered across the onsemi datasheet, distributor listings, and application notes.

RFQ پەیوەندی
NCP43080DMTTWG - Secondary-Side SR Controller | onsemi
NCP43080DMTTWG

NCP43080DMTTWG - Secondary-Side SR Controller | onsemi

The onsemi NCP43080DMTTWG is a secondary-side synchronous-rectifier controller for switched-mode power supplies, with an 8-WDFN 2 x 2 mm package. It is designed for flyback, quasi-resonant flyback, and LLC power-converter topologies. The controller coordinates an external synchronous-rectification MOSFET so that rectification losses can be reduced compared with a conventional diode rectifier. Its key documented functions include externally adjustable minimum off-time and on-time blanking periods, flexible support for different MOSFET packages and PCB layouts, and operation intended to provide reliable, low-noise synchronous-rectifier control. A synchronous-rectifier controller is a power-management IC used in the secondary circuit of an isolated or non-isolated offline power supply. Instead of allowing a diode to conduct during the secondary rectification interval, the controller drives an external MOSFET to act as a low-loss rectifier. The controller belongs to the broader sequence of switch-mode power-supply components: transformer or inductor energy transfer, primary switching, secondary rectification, output filtering, and regulated feedback. The NCP43080 family targets applications where efficiency and secondary-side behavior are important. Its blanking controls help prevent unwanted MOSFET turn-on or turn-off during switching transitions. These protections are especially relevant when leakage currents, ringing, transformer reset behavior, or differing MOSFET switching speeds could otherwise cause false gate-drive pulses. The exact electrical ratings, timing limits, pin names, and recommended external components require confirmation from the manufacturer datasheet and the selected transformer and MOSFET design. Typical implementation targets include isolated flyback chargers, quasi-resonant flyback adapters, power supplies for consumer electronics, and LLC converter secondary stages. The controller is especially relevant where a Schottky diode would otherwise dissipate significant power at high output current. The external MOSFET selection must be coordinated with output voltage, current, switching frequency, transformer reset behavior, gate-drive requirements, and thermal conditions. The principal design consideration is timing coordination between the primary switch and the secondary synchronous MOSFET. Minimum off-time, minimum on-time, propagation behavior, dead time, and layout parasitics determine whether the replacement can improve efficiency without introducing cross-conduction or shoot-through. The package must be placed according to the datasheet layout guidance, with attention to high-current source and return paths, gate-loop inductance, and thermal dissipation. This product page combines the verified onsemi product identity, distributor package information, the official NCP43080 datasheet link, and practical design guidance. Unavailable ratings and package details are intentionally marked for verification rather than inferred from generic controller families.

RFQ پەیوەندی
NCP4308DDR2G - 35V Synchronous Rectifier Controller | onsemi
NCP4308DDR2G

NCP4308DDR2G - 35V Synchronous Rectifier Controller | onsemi

The onsemi NCP4308DDR2G is a synchronous rectifier controller for switch-mode power supplies, with a 4 V to 35 V operating range, a 1 MHz switching frequency, and an SOIC-8 package. It supports secondary-side synchronous rectification in flyback, quasi-resonant flyback, and LLC power-conversion systems. Its 8 A current capability and adjustable blanking functions help accommodate different synchronous-rectifier MOSFET package types and circuit layouts. A synchronous rectifier controller is a power-management semiconductor that drives an external MOSFET on the secondary side of an isolated or non-isolated switching converter. By replacing diode conduction with low-loss MOSFET switching, it can reduce power loss during output-current transfer. The NCP4308 family belongs to the secondary-side controller, power-management IC, and switch-mode power-supply hierarchy. Key features include externally adjustable minimum off-time and on-time blanking periods, operation across discontinuous-conduction, continuous-conduction, and quasi-resonant flyback modes, and a 1 MHz switching-frequency capability. The controller is designed to provide reliable and low-noise operation of the synchronous-rectifier system while allowing the power stage to be tailored to the transformer, MOSFET, and PCB layout. The NCP4308 architecture coordinates gate timing with the secondary-side waveform. The adjustable timing features help prevent premature MOSFET turn-on or turn-off during ringing and transition intervals. Designers must still validate the timing window against the actual transformer reset behavior, MOSFET gate charge, leakage current, and operating frequency rather than treating the timing values as universal constants. Typical uses include AC-DC adapters, offline power supplies, flyback converters, quasi-resonant flyback converters, LLC converters, USB power supplies, and industrial power modules. In each case, the controller is paired with external synchronous-rectifier MOSFETs rather than acting as the primary-side converter controller. A key design consideration is maintaining adequate separation between the controller and high-current secondary-side switching nodes. Use the manufacturer’s recommended layout, minimize gate-loop area, place timing components close to their pins, and verify dead time, ringing, and cross-conduction behavior with an oscilloscope across the full input and load range.

RFQ پەیوەندی
NCP81111MNI3TXG - 3-Phase VR12.5/12.6 Digital Controller | onsemi
NCP81111MNI3TXG

NCP81111MNI3TXG - 3-Phase VR12.5/12.6 Digital Controller | onsemi

The onsemi NCP81111MNI3TXG is a high-performance, single-output, three-phase digital buck controller compliant with Intel VR12.5 and VR12.6 specifications, supplied in a 32-pin QFN (5x5 mm) package with exposed thermal pad. The device integrates a Serial VID (SVID) interface and an I2C control port, and operates at switching frequencies up to 5 MHz to support compact CPU core-voltage regulator solutions. A multiphase buck controller is a power-management IC (PMIC) that interleaves multiple synchronous buck phases to deliver high current at low voltage while spreading thermal dissipation across the PCB. Within the broader system hierarchy, the NCP81111 sits in the CPU core rail of a server, workstation, or embedded computing platform, between a 12 V (or higher) intermediate bus and the loadline-regulated Vcore output demanded by an Intel VR12.5/12.6 processor. The architecture combines precision analog current sensing with digital modulation to meet the stringent dynamic load, overshoot, and DC tolerance requirements of modern CPUs. Key features include three integrated gate drivers capable of driving external N-channel MOSFETs in a true multiphase topology, SVID bus communication for direct CPU-to-controller command, an I2C interface for telemetry, configuration, and fault readback, per-phase current balancing, dynamic phase add/drop, programmable loadline, and comprehensive protection including over-voltage, under-voltage, over-current, and over-temperature. The controller supports PMBus-compatible telemetry of output voltage, current, and temperature for system-level monitoring. The NCP81111 implements a digital control loop with adaptive voltage positioning and high-bandwidth error amplification, achieving fast transient response to VR12.5/12.6 step loads. Phase shedding dynamically disables phases at light load to maximize efficiency, while automatic phase add/drop maintains regulation under sudden load increases. The 5 MHz switching capability enables the use of small inductors and ceramic output capacitors, reducing board area compared to legacy controllers. Typical applications include Intel VR12.5/12.6-compliant server and workstation CPU core power, single-rail high-current POL converters in networking ASICs and FPGAs, graphics processor power in workstation add-in cards, and high-end embedded computing platforms. The exposed pad package supports sustained multiphase operation at tens of amps with appropriate thermal design. When designing with the NCP81111, follow the manufacturer's reference layout for the QFN exposed pad and place the current-sense resistors and bootstrap capacitors as close as possible to the controller pins. The SVID and I2C lines require pull-up resistors per the Intel VR12.5/12.6 design guide; verify timing with the target CPU's VR12.5/12.6 compliance checklist before tape-out.

RFQ پەیوەندی
NCP81269MNTXG - Synchronous Buck Controller, 2-Bit VID | onsemi
NCP81269MNTXG

NCP81269MNTXG - Synchronous Buck Controller, 2-Bit VID | onsemi

The onsemi NCP81269MNTXG is a synchronous buck controller with 2-bit VID inputs, optimized for converting battery or adapter voltage into the power supply rails required in notebook and desktop systems. Housed in a 20-pin QFN (HVQCCN) package, it features a switching frequency up to 600 kHz, automotive temperature grade support up to 125 °C, and dynamic slew-rate-controlled output voltages. A synchronous buck controller is a type of DC-DC switching controller that uses two MOSFETs in a half-bridge configuration to step down a DC input voltage to a lower regulated DC output. Compared to an asynchronous buck (diode-rectified), the synchronous topology replaces the Schottky rectifier with a low-RDS(on) MOSFET, which significantly improves efficiency at light-to-medium loads and reduces conduction losses. Synchronous buck controllers belong to the broader family of switching regulators (buck, boost, buck-boost), which themselves fall under the power management IC (PMIC) hierarchy for computing and portable platforms. Key features include a 2-bit VID (voltage identification) interface that allows dynamic output voltage slewing for power-state transitions (P-state, VID-based power management in modern CPUs and GPUs), an externally programmable soft-start via a single capacitor, and wide input voltage tolerance suitable for both battery and adapter operation. The 600 kHz switching frequency enables compact inductor selection, while the automotive temperature grade supports harsh-environment deployment. Technically, the NCP81269 integrates high-side and low-side MOSFET drivers, a fixed-frequency voltage-mode control loop, and the VID decoding logic directly on-chip. The 2-bit VID scheme provides four discrete output voltage setpoints selected by external logic inputs, allowing the system controller to command voltage changes for low-power states without software intervention. This makes the controller well suited to CPU/GPU core rails, chipset power, and DDR memory termination rails in space-constrained notebook platforms. Typical applications include notebook system rails, desktop motherboard buck rails, chipset and memory termination supplies, and embedded computing platforms requiring dynamic voltage scaling. The wide operating temperature range and automotive grade make it attractive for industrial and automotive infotainment boards that demand similar power-rail architectures. When designing with this controller, ensure the bootstrap capacitor is sized per the high-side driver's requirements and that the feedback compensation network is matched to the selected output L-C filter. The 2-bit VID inputs are referenced to the controller's logic supply; verify logic-level thresholds match the driving GPIO or system controller outputs. This page synthesizes distributor pricing, drop-in alternative guidance, and practical design notes drawn from manufacturer datasheet material - providing added engineering context not found in the original datasheet.

RFQ پەیوەندی
NCV1362ABDR2G - 50W Automotive QR Flyback Controller | onsemi
NCV1362ABDR2G

NCV1362ABDR2G - 50W Automotive QR Flyback Controller | onsemi

The onsemi NCV1362ABDR2G is a highly integrated quasi-resonant (QR) peak current-mode primary-side flyback controller targeting low-power off-line Switch-Mode Power Supplies (SMPS) from a few watts up to 50 W in automotive and commercial applications. Housed in an 8-pin SOIC (SOIC-8 / NB / 8-SOIC) package, the device operates with a switching frequency range of 1 kHz to 140 kHz (typical 110 kHz), a maximum switching frequency of 130 kHz, and is powered from a 6.5 V to 28 V supply on the VCC pin. A quasi-resonant flyback controller is a type of AC-DC offline switching controller that turns the primary MOSFET on when the drain voltage rings to its valley, dramatically lowering switching losses and EMI versus a hard-switched PWM controller at fixed frequency. It belongs to the controller hierarchy: AC-DC controller -> offline switcher -> quasi-resonant controller -> peak current-mode controller -> power management IC. Primary-side regulation (PSR) eliminates the opto-coupler and secondary reference, enabling tighter CV/CC accuracy with a smaller BOM. Key features of the NCV1362ABDR2G include quasi-resonant valley-switching for reduced EMI and improved efficiency, primary-side constant-voltage and constant-current regulation (no opto-coupler required), a wide VCC range of 6.5 V to 28 V, built-in protections (over-voltage, over-current, over-power, short-circuit, and thermal shutdown), and a 1 kHz to 140 kHz programmable switching-frequency range. Automotive-grade qualification per onsemi's NCV prefix supports AEC-Q100 applications such as USB chargers, e-bike chargers, and LED drivers. The controller uses a current-mode control architecture with a transconductance error amplifier and an internal reference, allowing the designer to set loop dynamics with a single external compensation network on the COMP pin. The quasi-resonant detection block identifies the drain-voltage valley and synchronizes turn-on, lowering dv/dt stress on the MOSFET and reducing conducted EMI by up to 10 dB relative to a fixed-frequency controller at the same load. Typical end uses include USB Type-C chargers (5 V / 3 A) for vehicles, 12 V-24 V auxiliary supplies in two-wheeler and four-wheeler electrical systems, LED driver front-stages, e-bike and e-scooter chargers, white-goods auxiliary supplies, and industrial IoT gateways requiring isolated low-power rails. The wide VCC tolerance also allows direct operation from rectified 12 V or 24 V battery buses without an external regulator. When designing with the NCV1362ABDR2G, place the gate-drive resistor and the current-sense resistor as close to the CS and DRV pins as possible, and keep the high-voltage drain loop area minimal to limit ringing that could falsely trigger the QR detector. The VCC hold-up capacitance must sustain operation through the auxiliary-winding dropout interval at minimum line voltage.

RFQ پەیوەندی
NCV68261MTWAITBG - Ideal Diode HS NMOS Controller | onsemi
NCV68261MTWAITBG

NCV68261MTWAITBG - Ideal Diode HS NMOS Controller | onsemi

The onsemi NCV68261MTWAITBG is a reverse polarity protection and ideal diode NMOS controller with an optional high side switch function, driving one or two external N-channel MOSFETs from a 6-pin WDFNW (2x2 mm) surface-mount package. It is intended as a lower-loss, lower-forward-voltage replacement for power rectifier diodes and mechanical power switches in automotive power paths. An ideal diode controller is a power-management device that drives an external MOSFET to emulate a diode without the conduction losses of a p-n or Schottky junction. Where a conventional rectifier diode drops roughly 0.5 V to 0.7 V and dissipates significant heat at high current, an ideal diode stage drops only Iload x Rds(on) of the MOSFET, cutting forward-voltage loss by an order of magnitude. In the vehicle power hierarchy - battery feed, reverse-polarity guard, load switch, point-of-load regulator - this part occupies the protection and switching layer, downstream of the fuse box and upstream of the load. Key features include MOSFET gate control driven directly by the state of the Enable pin, support for one or two N-channel MOSFETs in ideal-diode or high-side-switch configurations, and automotive-grade qualification signaled by the NCV prefix. Replacing a mechanical relay or a series Schottky with this controller plus a low-Rds(on) NMOS reduces forward voltage, power dissipation, and hot-swap contact wear in the power distribution path. Technically, the controller senses the anode-cathode orientation across the external MOSFET and adjusts the gate to block reverse current, while the enable input determines ON/OFF state. Because the external MOSFET sets the current rating, designers can scale the same controller from a few amperes to tens of amperes by selecting an appropriate NMOS - a key advantage over fixed-rating protection ICs. Typical applications include automotive battery reverse-polarity protection, 12 V and 24 V power distribution modules, ECU main power feeds, and industrial systems replacing mechanical relays with solid-state switching. The automotive temperature-grade rating suits underhood and body-electronics environments. Design consideration: the forward-drop saving depends entirely on the chosen MOSFET Rds(on); verify gate-drive amplitude and reverse-blocking behavior at cold crank and load-dump conditions before finalizing the BOM. This page synthesizes distributor pricing, functional cross-references, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
NJW4132U2-A - 40V 1.75A Boost Converter IC | Nisshinbo
NJW4132U2-A

NJW4132U2-A - 40V 1.75A Boost Converter IC | Nisshinbo

The Nisshinbo Micro Devices NJW4132U2-A-TE2 is a 45V-tolerant, 1.75A output current boost (step-up) switching regulator IC integrating a 40V power MOSFET in a compact SOT-89-5/6 surface-mount package. It operates from a wide 4.5V to 40V input range and produces an adjustable output from 1V up to ~38V, making it well suited for industrial 24V/28V bus rails and battery-powered systems that must be boosted above the supply voltage. A boost converter (also called a step-up switching regulator) is a switching power topology that uses an inductor, a power switch, and a rectifier diode to deliver an output voltage higher than the input. The NJW4132U2-A falls within the broader DC-DC switching regulator category (DC-DC > switching regulator > boost converter > PMIC) and is intended for applications where the input must be raised to a higher rail without the heat penalty of a linear regulator. Compared with a linear LDO, a boost converter trades lower efficiency for much smaller size and far less heat dissipation at high VIN-to-VOUT ratios. Key features include 45V absolute maximum input rating, 1.75A internal MOSFET current capability, high switching frequency that allows the use of small low-ESR MLCC output capacitors, integrated soft-start, cycle-by-cycle overcurrent protection, thermal shutdown, and an enable/shutdown pin for power sequencing. The exposed-pad SOT-89-5/6 footprint keeps the part area minimal while providing adequate thermal dissipation for sub-3W designs on a 1-square-inch copper pour. Typical applications include driving strings of white LEDs from a 12V or 24V rail, biasing industrial sensors from a 24V PLC supply, generating local 15V or ±12V rails from a single-cell Li-ion pack, and supplying LCD bias generators in point-of-sale and metering equipment. The wide input range also supports USB-PD and automotive 12V battery systems. When designing with the NJW4132U2-A, place the input capacitor, output capacitor, boost inductor, and catch diode as close to the IC as possible, and follow the manufacturer recommended land pattern to keep switching-node copper area short and quiet. Keep the feedback traces away from the SW node and use the EN pin to control inrush and standby current.

RFQ پەیوەندی
NJW4132U2-A-TE2 - 40V 1.75A Boost Converter | Nisshinbo Micro Devices
NJW4132U2-A-TE2

NJW4132U2-A-TE2 - 40V 1.75A Boost Converter | Nisshinbo Micro Devices

The Nisshinbo Micro Devices NJW4132U2-A-TE2 is a 45V-tolerant, 1.75A peak-current boost (step-up) switching converter IC with an integrated low-RDS(on) N-channel MOSFET, housed in a compact SOT-89-5/6 surface-mount package. It accepts a wide 4.5V to 40V input range, supports adjustable output voltages from 1V upward (set by external feedback resistor), and operates at high switching frequency with low-ESR MLCC support on the output - making it ideal for space-constrained industrial and automotive subsystems. What is a boost converter? A boost converter is a switching DC-DC converter topology that produces an output voltage higher than its input. In the broader power management hierarchy, it sits under DC-DC converters, which themselves belong to power management ICs (PMICs). Boost converters use an inductor, switch, diode, and output capacitor to store and release energy, achieving efficiencies typically 80-95% that far exceed linear regulators when VIN is significantly below VOUT. Key features of the NJW4132U2-A-TE2 include: 1.75A internal switch current, wide VIN 4.5V to 40V, high-frequency operation enabling small external LC components, MLCC-compatible output, integrated 45V MOSFET for derating transistor strength, built-in overcurrent protection, thermal shutdown, and an enable/standby pin. The SOT-89-5/6 package provides an exposed tab for thermal dissipation and occupies a footprint suitable for handheld and panel-mount designs where board area is at a premium. The NJW4132U2 uses peak-current-mode PWM control with internal compensation, providing stable transient response across line and load variations. The wide 40V input withstand capability allows direct connection to 12V or 24V industrial battery rails, while the high-side drive architecture and internal 45V MOSFET derating protect against inductive switching transients. According to the Nisshinbo Micro Devices datasheet, the converter maintains regulation across the full input range and offers cycle-by-cycle current limiting. Typical applications include industrial 24V bus boost to 36V/48V rails, automotive bias supplies from 12V battery to logic-level rails, LED backlight boost converters for panel displays, and battery-powered portable instruments. The wide input range particularly suits 12V/24V lead-acid battery systems where cold-crank transients and load-dump surges exceed normal operating voltage. When designing with this device, derate the internal MOSFET at high VIN - the 45V rating provides margin against load-dump transients in 24V automotive systems. Place the input capacitor close to the IC and use a Schottky rectifier with low reverse recovery to maximize efficiency. According to the Nisshinbo datasheet, the feedback resistor divider should use 1%-tolerance parts for output voltage accuracy. This page synthesizes distributor pricing, drop-in SOT-89-5 same-brand alternatives (NJW4132U2-B-TE2, NJW4132U2-C-TE2 family variants), and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
NJW4132U2-CT1-TE1 - 45V/1.75A 2MHz Boost Converter | Nisshinbo
NJW4132U2-CT1-TE1

NJW4132U2-CT1-TE1 - 45V/1.75A 2MHz Boost Converter | Nisshinbo

The Nisshinbo Micro Devices NJW4132U2-CT1-TE1 is a 45V/1.75A current-mode boost (step-up) switching regulator IC housed in a compact SOT-89-5/6 surface-mount package. It operates from a wide 4.5V to 40V input range, integrates a 45V/1.75A power MOSFET, and switches at a fixed 2.0 MHz oscillation frequency that supports small ceramic output capacitors. The output voltage is externally adjustable, with the standard variant tracking a 1V reference, and the device delivers up to 2.25A of switch current per the distributor catalog listings. A boost (step-up) converter is a type of switching DC-DC converter that produces an output voltage higher than its input voltage. Boost converters belong to the broader switching regulator family, which also includes buck (step-down), buck-boost, and SEPIC topologies. Within the power management hierarchy they sit between the linear regulator (low noise, low VIN-VOUT headroom) and the charge-pump (low power, simple architecture). High-frequency switching regulators like the NJW4132 enable small magnetics and ceramic output capacitors, replacing the bulky electrolytics required by older converters running at 100 kHz to 500 kHz. Key features include the 2 MHz switching frequency that minimizes passive component footprint, integrated 45V power switch that withstands automotive load-dump transients, ceramic output capacitor compatibility for low-ESR designs, and built-in protections (overcurrent, thermal shutdown, undervoltage lockout) per the manufacturer datasheet. The 4.5V to 40V input range covers 5V, 12V, 24V, and 36V industrial bus rails. The NJW4132U2 uses peak-current-mode control architecture with internal slope compensation, providing stable loop response across a wide range of load and line conditions. The 2 MHz oscillator and small SOT-89-5/6 package allow single-sided PCB assembly in space-constrained applications. The high 45V switch rating supplies designs that must ride through load-dump pulses on 12V or 24V automotive buses. Typical applications include bias supplies for LCD/OLED display panels, point-of-load (POL) regulators after a 12V or 24V bus, LED backlight drivers, battery-powered industrial equipment, and energy-harvesting power conditioning. The wide VIN range and small footprint make it particularly attractive for body-electronics and metering end nodes. When designing with this part, ensure the inductor saturation current exceeds the 1.75A peak switch rating, and place input capacitors close to the IC to minimize switching noise. The thermal pad of the SOT-89-5/6 package requires adequate copper to keep junction temperature below the 150C maximum under worst-case load. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, and practical thermal design notes that supplement the manufacturer's datasheet and help shorten the design review path.

RFQ پەیوەندی
PCA9421 - PMIC 2 Buck + 2 LDO I2C, Li-ion | NXP
PCA9421

PCA9421 - PMIC 2 Buck + 2 LDO I2C, Li-ion | NXP

The NXP PCA9421 is a highly integrated power management IC (PMIC) providing two step-down (buck) DC-DC converters with I2C-programmable output voltages plus two LDO regulators, designed for 5V input operation in low-power microcontroller applications, and available in an HVQFN24 (BS) package and a WLCSP25 (UK) package. A PMIC (Power Management IC) is a specialized voltage regulator and power management device that integrates multiple power conversion stages - typically buck converters, LDOs, load switches, and supervision functions - into a single semiconductor. In the power management hierarchy, a PMIC sits above individual DC-DC converters and linear regulators, replacing several discrete power management ICs with one programmable solution, reducing board area, bill-of-materials count, and overall system cost. Key features of the PCA9421 include its dual buck converter architecture with I2C-programmable output voltages, two integrated LDO regulators for low-noise analog or digital rails, and operation from a 5V adapter or regulated supply as indicated by distributor listings. This level of integration makes the part a full power management solution rather than a single-rail regulator, which is its principal differentiator against discrete buck-plus-LDO combinations. Technically, the PCA9421 belongs to the NXP PCA9420/PCA9421 PMIC family, which NXP targets specifically at low-power microcontroller applications and similar systems powered by Li-ion battery and/or a 5V adapter in non-portable applications. The I2C interface allows a host microcontroller to adjust buck output voltages dynamically, supporting dynamic voltage scaling and power-mode sequencing in embedded designs. The two package options - HVQFN24 (BS suffix) and WLCSP25 (UK suffix) - give designers a choice between a hand-inspectable QFN footprint and an ultra-compact wafer-level chip-scale package for space-constrained boards. Typical applications include low-power microcontroller power supplies, battery-powered IoT sensor nodes, portable and non-portable devices powered by Li-ion cells or 5V adapters, and general embedded systems requiring multiple sequenced voltage rails from a single input. When designing with the PCA9421, consult the NXP datasheet for the exact buck and LDO current limits, programmable output voltage ranges, and I2C register map, and verify thermal performance for the chosen package option before finalizing the PCB layout. This page synthesizes distributor pricing context, same-family drop-in alternatives, application guidance, and design notes that go beyond the information available on the manufacturer datasheet alone, providing engineers with a consolidated selection resource.

RFQ پەیوەندی