DC-DC Converters
بەرهەمەکان (770+)
PTH04T241W - 10A, 2.2-5.5V Input POL Power Module | TI
The Texas Instruments PTH04T241W is a 10-A rated, non-isolated point-of-load (POL) DC-DC converter power module operating from a 2.2V to 5.5V input with a wide adjustable output of 0.69V to 3.6V, set by a single external resistor. The module is optimized for all-ceramic output capacitor designs and belongs to the second generation of the popular PTH series, offering a reduced footprint and additional features over the original family. A non-isolated power module is a complete DC-DC converter that integrates the PWM controller, power MOSFETs, inductor, and compensation network into a single surface-mount package, delivering a regulated output without galvanic isolation. Such modules sit within the voltage regulator hierarchy, specifically the buck (step-down) DC-DC converter family of power management ICs, and dramatically reduce design time versus discrete converter implementations. Key features include up to 96% efficiency, a total output voltage variation of only plus/minus 1.5%, and TurboTrans technology, which lets a single resistor tailor transient response and reduce required output capacitance. Remote sense, output voltage sequencing, and under-voltage lockout support reliable multi-rail systems. Internally, the PTH04T241W uses a synchronous buck topology with integrated MOSFETs and fixed-frequency PWM control. The TurboTrans control loop optimization allows engineers to meet aggressive load-step requirements typical of modern processors without oversizing capacitors, while the all-ceramic-capacitor optimization lowers ESR-related losses and improves long-term reliability since ceramic capacitors do not wear out like electrolytics. Typical applications include powering DSPs, FPGAs, ASICs, and microprocessors in networking, telecom, and data-communication equipment, where 3.3V or 5V intermediate buses must be stepped down to low core voltages at ampere-level loads. The compact footprint suits space-constrained line cards and blades. When designing, size the TurboTrans resistor to the expected load transient, follow datasheet input/output capacitor recommendations, and account for thermal dissipation at high output current using adequate PCB copper area.
PTH05050WAZ - 6A 5V-In Wide-Output Adjust PoL Module | Texas Instruments
The Texas Instruments PTH05050WAZ is a 6 A, 5 V-input non-isolated wide-output-adjust Power Module with Auto-Track sequencing, packaged in a 6-pin DIPMODULE (EUV) surface-mount form factor. It accepts a 4.5 V to 5.5 V input and produces an adjustable output from 0.8 V to 3.6 V at up to 6 A continuous load, delivering 21.6 W of output power with efficiencies as high as 95 percent and a power density of 135 W/in³. The 'Z' suffix designates a Pb-free, RoHS-compliant surface-mount termination suitable for lead-free reflow. A non-isolated Point-of-Load (PoL) DC-DC module is a fully integrated switching converter that mounts directly next to a load on the same printed circuit board as its load IC, eliminating the intermediate bulk converter stage and the parasitic losses of long power-trace runs. PoL modules sit within the broader hierarchy of DC-DC converters, which in turn belong to the power management semiconductor category that converts and regulates voltage rails in distributed power architectures. Key features of the PTH05050WAZ include pre-bias start-up for safe paralleling with other supplies, an output ON/OFF inhibit input, Margin Up/Down control pins for board-level testing, Auto-Track sequencing that lets multiple modules ramp together or track an external rail, and the surface-mount through-hole DIPMODULE footprint that combines low-inductance SMT pads with mechanical through-hole pins. The wide-output-adjust range (0.8 V to 3.6 V) covers the core voltages of modern DSPs, FPGAs, ASICs, and DDR memory rails. Architecturally, the PTH05050WAZ is built around a synchronous buck topology with integrated power MOSFETs, a power inductor, and control IC all inside the module body. This integration removes the need for external magnetics design and significantly reduces radiated EMI by keeping the high-di/dt loop inside the package, while still delivering high efficiency across the 4.5 V to 5.5 V nominal 5 V intermediate bus. Typical applications include 5 V intermediate-bus architectures powering low-voltage DSPs, FPGAs, ASICs, and DDR memory; telecom and networking line cards requiring sequenced multi-rail power; industrial controllers and distributed-power systems; and any board that needs a compact, high-efficiency point-of-load converter with sequencing and margining built in. When designing with this part, follow the manufacturer's recommended input/output capacitor values, sequence rails using Auto-Track, and pay attention to derating at high ambient temperatures above 55 °C. The PTH05050WAZ is a member of the well-known TI PTH/POL family, making it drop-in compatible with several 6 A, 5 V-input siblings.
PTH05T210W - 30A, 5V Input PoL Power Module | Texas Instruments
The Texas Instruments PTH05T210W is a high-performance 30-A rated, non-isolated point-of-load (PoL) DC-DC converter power module using a multi-phase switch-mode topology. It operates from a 4.5V to 5.5V input and delivers a wide adjustable output voltage from 0.7V to 3.6V, targeting low-voltage, high-current loads in space-constrained systems. This second-generation PTH-series module offers a reduced footprint and improved features over the original PTH family. A non-isolated PoL module is a type of DC-DC converter (part of the broader voltage regulator / power management IC hierarchy) that steps a distribution rail down to a regulated low voltage close to the load, without galvanic isolation. It integrates the controller, power MOSFETs, inductor, and loop compensation into one packaged module, replacing dozens of discrete components and dramatically shortening power-supply design cycles. Key features include TI's proprietary TurboTrans technology, which lets designers optimize transient response and reduce required output capacitance, and Auto-Track sequencing for controlled power-up/down of multiple modules. Output voltage adjust is accomplished with a single external resistor, and the module provides remote sense for tight load regulation plus a power-good flag for system supervision. Multi-phase operation achieves high efficiency (typically around 96% for 5V-in to 3.3V-out per TI data) while minimizing output ripple. Architecturally, the multi-phase topology interleaves switching channels so ripple currents partially cancel, allowing smaller magnetics and faster load-transient response than single-phase bucks at 30 A. The open-frame module construction aids airflow cooling in forced-air systems. Typical applications include powering DSPs, FPGAs, ASICs, and microprocessors in telecom, networking, server, storage, and industrial equipment. The 30-A capability and wide output range also fit test and measurement platforms. Design consideration: follow the datasheet input/output capacitance recommendations to maintain stability and transient response; TurboTrans pin settings should be tuned to the actual output capacitor network for best performance.
PXE1410CDM-G003 - Infineon Digital Multiphase Power Controller
The Infineon Technologies PXE1410CDM-G003 is a digital multiphase DC-DC switching controller in a PG-VQFN-40-13 package, with the verified distributor listing identifying it as a power-management controller for demanding voltage-regulator designs. Its stated function is digital control of external power stages, making it suitable for high-current server, AI accelerator, and telecom rails when paired with compatible Infineon OptiMOS DrMOS devices. The package and device family place it in the controller category rather than the final power-stage category. A digital multiphase controller coordinates multiple PWM power channels to distribute high output current and reduce the burden on any single stage. In a server or accelerator rail, it can receive configuration and telemetry commands through its digital control interface, while the external DrMOS devices perform the high-current switching. The PXE1410CDM-G003 is therefore a controller component whose final converter performance also depends on the selected power stages, inductors, MOSFETs, sensing network, compensation settings, and PCB implementation. The verified data identifies the part as a VQFN-40 device and describes it as a Primarion digital power controller intended for high-current applications. The available snippets also associate the family with adaptive voltage positioning, precision current and temperature telemetry, and interfaces including PMBus or I2C. These features are useful when a power rail requires programmable control, monitoring, and coordinated phase operation, but exact numerical limits, switching frequency, phase count, voltage range, current rating, thermal resistance, and pin-level electrical limits are not supplied in the provided data. Infineon’s PXE1410CDM-G003 is best evaluated as a platform component rather than a standalone regulator. Designers should select compatible external power stages and confirm all controller requirements against the manufacturer datasheet before layout release. The controller’s digital configuration, phase sequencing, current-sense implementation, fault handling, and thermal telemetry must be validated in the complete converter design rather than inferred from distributor category labels. Typical applications include high-current server voltage rails, AI accelerator power delivery, telecom equipment, and other regulated systems requiring multiple synchronized power stages. The principal design trade-off is flexibility versus implementation complexity: digital multiphase control can improve rail scalability and observability, but it demands careful firmware or host configuration, power-stage coordination, compensation, fault-response design, and high-current PCB layout. The most important layout consideration is keeping the controller, sensing paths, gate-drive connections, and power-stage current loops compact and appropriately partitioned. A multilayer board with short high-current paths, low-inductance switching loops, Kelvin current-sense connections, and controlled return paths is generally preferable to a sprawling two-layer implementation. Use the manufacturer’s recommended application circuit and layout guidance before copying a generic reference design. This page consolidates the verified distributor identity, package information, pricing indication, and available source links for PXE1410CDM-G003, while clearly separating confirmed data from parameters that still require datasheet confirmation.
PXM1310CDMG003XTMA1 - VR12.5/VR13 Digital 3+1 DDR Controller | Infineon
The Infineon PXM1310CDMG003XTMA1 is a digital dual-output 3+1 phase PWM controller compliant with Intel VR12.5 and VR13 specifications, designed for high-current CPU/GPU core voltage regulation and DDR memory power in server, workstation, and high-end desktop platforms. Housed in a 40-pin PG-VQFN package with exposed thermal pad, it integrates six PWM outputs plus a peripheral rail to manage both the core voltage regulator and the memory subsystem in a single IC. According to the Infineon Primarion datasheet family, the controller pairs with Infineon PowIRstage devices (such as the TDA21472 or TDA21535) to form a complete multiphase synchronous buck solution. A digital multiphase buck controller is a specialized power management IC that uses firmware-configurable loop compensation, telemetry, and adaptive voltage positioning to deliver tightly regulated core voltages to modern processors. Within the broader power management taxonomy, it sits as a DC-DC controller above simple voltage regulators and below fully integrated power modules; the 3+1 phase architecture specifically allocates three phases to the core rail and one phase to the system agent/graphics sub-rail, which is the typical Intel VR12.5/VR13 topology for desktop and entry-server CPUs. Key features of the PXM1310CDMG003XTMA1 include Intel VR12.5/VR13 protocol support with SVID/I2C telemetry, six PWM outputs for flexible phase assignment, embedded firmware for adaptive voltage positioning and fault response, and per-phase current balancing. The 40-pin PG-VQFN package exposes the thermal pad directly to the PCB copper pour, enabling heat extraction through the top-side power stages rather than through the controller itself. The device uses a state-machine-based digital control loop rather than an analog Type-III compensator, which simplifies design-in by eliminating external compensation components. Telemetry such as output voltage, current, and temperature is reported over PMBus/I2C for closed-loop platform monitoring, while the integrated fault handler protects against over-voltage, under-voltage, over-current, and over-temperature conditions. This architecture replaces what traditionally required a supervisor IC plus analog PWM controller combination. Typical applications include Intel VR12.5/VR13 desktop and server CPU core rails, DDR3/DDR4 memory power (VDDQ and VTT), workstation motherboard voltage regulators, and embedded computing platforms that require PMBus-programmable telemetry. The 3+1 phase configuration suits 95W to 150W TDP processor classes where digital telemetry and adaptive transient response are required. When designing with this part, validate that the chosen PowIRstage supports the controller's PWM frequency and current sense scheme, and observe Infineon's layout guidance for the SVID/I2C bus routing to avoid coupling into the switching node. The exposed thermal pad must be soldered to a continuous ground copper pour for both thermal dissipation and low-impedance gate return paths.
RHP50000 - 12.5A Silent Switcher 2 Step-Down | Analog Devices
The RHP50000-CSL is a very small, low noise, monolithic step-down DC/DC converter from Analog Devices, capable of delivering up to 12.5A of output current from a 2.25V to 5.5V input supply. It employs the Silent Switcher 2 architecture with internal hot loop bypass capacitors to achieve both low EMI and high efficiency at switching frequencies as high as 5MHz. The device is available in an 18-lead TFQFN package with exposed pad, making it suitable for space-constrained, high-current power delivery in commercial space and other demanding applications. A step-down DC/DC converter, also known as a buck converter, is a type of switching regulator that efficiently converts a higher input voltage to a lower output voltage. Unlike linear regulators, which dissipate excess power as heat, buck converters use switching elements and energy storage components to achieve high efficiency, especially when the input-to-output voltage difference is large. The RHP50000 is a synchronous buck converter, meaning it uses two MOSFETs (high-side and low-side) to minimize conduction losses and eliminate the need for an external Schottky diode. This architecture is fundamental to modern power management ICs, enabling compact, high-current power solutions for processors, FPGAs, and other digital loads. Key features of the RHP50000 include its 12.5A output current capability, 2.25V to 5.5V input voltage range, and adjustable output voltage down to 0.5V. The Silent Switcher 2 architecture integrates bypass capacitors to reduce EMI, simplifying PCB layout and reducing the need for external filtering. The device operates at switching frequencies up to 5MHz, allowing the use of small inductors and capacitors, which reduces solution footprint. It also features a precision enable pin, soft-start, and power-good output for reliable power sequencing. Technically, the RHP50000 uses a current-mode control architecture with internal compensation, providing fast transient response and stable operation over a wide range of output capacitors. The integrated hot loop bypass capacitors minimize parasitic inductance in the switching loops, which is critical for achieving low EMI at high frequencies. The device also includes overcurrent protection, thermal shutdown, and undervoltage lockout to ensure robust operation in harsh environments. Typical applications include powering FPGAs, ASICs, and processors in commercial space systems, as well as high-current point-of-load (POL) converters in networking, telecommunications, and industrial equipment. The wide input range and high output current make it ideal for 5V or 3.3V rails that need to step down to core voltages like 1.2V or 0.9V. When designing with the RHP50000, pay careful attention to the input and output capacitor placement to minimize parasitic inductance. The AGND pin should be connected to the negative terminal of the output capacitor at the load for good load regulation. Use a solid ground plane and follow the layout guidelines in the datasheet to achieve the best EMI performance.
RT6150BGQW - 0.8A Buck-Boost DC/DC Converter | Richtek
The Richtek RT6150BGQW is a high-efficiency, fixed-frequency current-mode Buck-Boost DC/DC switching regulator delivering up to 800 mA of output current in a 10-pin WDFN (GQW) exposed-pad package. It operates from input voltages above, below, or equal to the output voltage with an adjustable output starting at 1.8 V, providing a continuous transfer function through all operating modes including buck, boost, and buck-boost regions. A buck-boost converter is a switched-mode power supply topology that maintains a stable output voltage even when the input voltage crosses the regulated output level. Unlike pure buck or pure boost converters, the buck-boost can both step down (VIN > VOUT) and step up (VIN < VOUT) within the same power stage, making it ideal for battery-powered systems where the cell voltage starts above and ends below the load rail. The RT6150 belongs to the broader switching regulator family within power management ICs, sitting alongside buck, boost, and SEPIC converters. Key features include a 1 MHz switching frequency that enables the use of small external inductors and ceramic capacitors, a low 60 µA quiescent current in Power Save Mode (PSM) for extended battery life, and user-controlled PSM activation via the PS pin. The device integrates two N-MOSFET and two P-MOSFET switches, eliminating the need for external FETs. Protection features include cycle-by-cycle current limit, thermal shutdown, and soft-start. Architecturally, the RT6150 uses a current-mode control scheme that provides excellent line and load transient response while simplifying compensation. The 1 MHz fixed frequency enables predictable EMI behavior and the use of small magnetics, while the integrated 4-switch bridge provides seamless transitions between operating modes without output voltage discontinuity. Typical applications include single-cell lithium-ion battery powered devices, multi-cell alkaline or Ni-MH systems, portable industrial instruments, USB-powered peripherals, and IoT sensor nodes. The buck-boost topology is particularly valuable when the battery voltage range spans the load rail - for example, a single Li-ion cell (3.0 V to 4.2 V) powering a 3.3 V rail. Designers should evaluate inductor ripple current, output capacitor ESR, and PSM/PWM mode trade-offs. In PWM mode (PS pin high), the regulator operates at fixed 1 MHz for low-ripple performance; in PSM mode (PS pin low), it skips pulses at light load to maximize efficiency. Adequate thermal copper under the exposed pad is essential for full 0.8 A operation. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical buck-boost design notes that complement the manufacturer datasheet.
RT8071AZQW - 3A 2MHz Synchronous Step-Down Converter | Richtek
The Richtek RT8071AZQW is a 3A, 2 MHz synchronous step-down DC-DC converter housed in a 10-pin DFN-10-EP (3x3 mm) package with an exposed thermal pad. It operates from a 2.7V to 5.5V input voltage range and delivers an adjustable output voltage from 0.6V up to VIN, making it well suited for point-of-load regulation in space-constrained designs. Internal MOSFETs (P-channel high-side and N-channel low-side) eliminate the need for external switches, and the 2 MHz nominal switching frequency permits the use of small surface-mount inductors and ceramic output capacitors. A synchronous step-down (buck) converter is a type of DC-DC switching regulator that steps a higher DC input voltage down to a lower regulated DC output voltage. Buck converters belong to the broader family of switch-mode power supplies (SMPS), which sit above linear regulators in efficiency but require an inductor, output capacitor, and feedback compensation. Within the SMPS hierarchy, the RT8071AZQW is positioned as a small-footprint, high-frequency point-of-load converter that targets portable, handheld, and embedded designs where PCB real estate is at a premium. Key features include a typical peak current limit of approximately 4 A for robust transient handling, internal soft-start to limit inrush current, power-good indication for sequencing, and a typical quiescent current on the order of tens of microamperes to maximize light-load efficiency. The exposed thermal pad on the DFN-10 package provides a low thermal resistance path, allowing the device to deliver 3 A continuously without an external heatsink when the PCB copper area is properly sized. The RT8071AZQW uses voltage-mode PWM control with internal compensation, which simplifies the external BOM to an input capacitor, an inductor, an output capacitor, and two feedback resistors. The 2 MHz switching frequency keeps the converter above the AM broadcast band, avoiding audible interference in audio-adjacent designs. Internal synchronous rectification eliminates the external Schottky diode required by older buck topologies, improving efficiency at light loads. Typical applications include portable media players, set-top boxes, blade servers, notebook computers, and distributed 5V POL rails in networking and storage equipment. The wide 2.7V-5.5V input range covers single-cell Li-ion, USB, and 3.3V/5V system bus rails, while the adjustable output supports DDR memory, FPGA core rails, and I/O supplies. When designing with this part, keep the input ceramic capacitor within 2 mm of the VIN and GND pins, route the feedback trace away from the SW node, and provide at least four thermal vias under the exposed pad to keep junction temperature within ratings at full 3 A load. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical PCB layout notes that go beyond the manufacturer datasheet, enabling faster design-in and BOM decisions.
RT8077GQW - 2A, 2MHz Sync Step-Down Converter | Richtek
The Richtek RT8077GQW is a high-efficiency, 2 MHz synchronous step-down DC/DC converter that delivers up to 2 A of output current from a 2.6 V to 5.5 V input rail, packaged in an 8-pin WDFN (2x2 mm) with an exposed thermal pad. It provides an adjustable regulated output from 0.8 V to 5 V, an internal synchronous power stage that eliminates the need for an external Schottky diode, and a switching frequency programmable up to 2 MHz via an external resistor. The 100% maximum duty cycle allows low-dropout operation, which extends runtime in battery-powered portable systems where headroom shrinks as the cell discharges. A synchronous buck converter (also called a step-down switching regulator) is a switched-mode power supply topology that converts a higher DC input voltage to a lower DC output voltage using two MOSFET switches, an inductor, and output capacitance. Compared to linear regulators, buck converters achieve 90-95% efficiency at moderate load currents because they cycle energy through an inductor rather than dissipating it as heat. Synchronous buck converters replace the conventional rectifier diode with a low-Rdson MOSFET to further reduce conduction loss. Within the power management IC hierarchy, this places the RT8077GQW in the DC-DC converter family, which sits above simple LDO regulators and below system PMICs in terms of integration and complexity. Key features include 2 A continuous output current, a programmable switching frequency up to 2 MHz (which keeps the inductor and capacitors very small), 100% duty-cycle low-dropout operation, internal soft-start, cycle-by-cycle current limit, and thermal shutdown. The exposed-pad WDFN-8 package provides a low thermal resistance path, enabling 2 A delivery without an external heatsink in typical 3.3 V to 1.8 V or 3.3 V to 1.2 V point-of-load applications. The RT8077GQW uses a peak current-mode control architecture with internal compensation, which simplifies the external BOM to a minimum of five components: input capacitor, output capacitor, inductor, feedback resistor divider, and frequency-setting resistor. The high 2 MHz switching frequency minimizes output ripple and allows the use of a small 1 µH to 2.2 µH chip inductor, which is essential in space-constrained portable and wearable designs. Typical applications include single-cell Li-ion powered portable devices, USB-powered peripherals, set-top box and HDTV point-of-load rails, solid-state drive (SSD) power, and FPGA/CPU core voltage generation in 5 V input systems. The wide 2.6 V to 5.5 V input covers both USB 5 V and single-cell Li-ion (3.0 V to 4.2 V) rails directly without a pre-regulator. When designing with this part, select the inductor based on the chosen switching frequency and ripple target - typically 1 µH to 2.2 µH at 2 MHz with less than 30% peak-to-peak inductor current ripple. Place the input ceramic capacitor as close as possible to the PGND and VIN pins to minimize switching-node ringing. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
RT8299AZSP - 3A, 24V Synchronous Step-Down Converter | Richtek
The Richtek RT8299AZSP is a 3 A continuous-output, 24 V synchronous step-down DC/DC converter with internal power MOSFETs, packaged in an 8-pin SOP with exposed pad (SOP-8EP). It operates from a 3 V to 24 V input range, delivers an adjustable 0.8 V to 15 V output, and switches at a fixed 500 kHz, balancing small external magnetics with respectable transient response. Current-mode control with cycle-by-cycle current limit is used for short-circuit protection and loop stability. What is a synchronous step-down converter? A synchronous buck regulator is a type of switched-mode power supply (SMPS) that uses both a high-side and a low-side MOSFET (often integrated) to convert a higher DC input voltage to a lower DC output voltage. Compared to an asynchronous buck (with a freewheeling diode), a synchronous buck replaces the diode with a MOSFET, which dramatically reduces conduction loss, raises efficiency (typically 90%+), and eliminates the rectifier reverse-recovery loss. Within the broader taxonomy, a buck converter is a DC/DC converter, which is a sub-category of voltage regulator, itself part of power management ICs. The RT8299 family is targeted at distributed point-of-load (POL) rails where high efficiency at moderate current is required. Key specifications include the 3 V-24 V input range, 0.8 V-15 V adjustable output, 3 A continuous load, fixed 500 kHz switching frequency, internal high-side and low-side MOSFETs, and SOP-8EP package with an exposed thermal pad for improved heat spreading. Current-mode control eases loop compensation, while internal soft-start reduces inrush current at power-up. Architecturally, the RT8299 integrates a high-side N-MOSFET, a low-side N-MOSFET, a 0.8 V reference, an error amplifier, a PWM controller, and protection circuitry (OCP, OVP, UVLO, thermal shutdown) into one die. The exposed pad on the SOP-8EP package reduces thermal resistance to roughly 40 C/W (per the manufacturer datasheet thermal table), enabling full 3 A output at elevated ambient temperatures with proper board layout. Typical applications include 12 V bus to 3.3 V/5 V point-of-load conversion for industrial controllers, consumer electronics (set-top boxes, LCD TVs), USB Type-C powered devices, distributed POL supplies in networking equipment, and battery-powered systems running from 2- to 4-cell Li-ion packs (8.4 V-16.8 V nominal). At light loads the device still operates in forced-PWM, so efficiency is moderate at very low currents. When designing with the RT8299AZSP, choose an inductor with low DCR (typically 2.2 µH to 4.7 µH), use ceramic input and output capacitors rated for the switching ripple current, and keep the high-current loop (IN-SW-PGND) tight on the PCB. Ensure the exposed pad is soldered to a copper area of at least 1 sq inch for the full 3 A continuous rating. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design guidance not found in the manufacturer datasheet.
RTQ2183-QA - 3A 5.5V Automotive Sync Buck Converter | Richtek
The Richtek RTQ2183-QA is a 3 A automotive-grade synchronous buck converter operating from 2.5 V to 5.5 V input and producing an adjustable output from 0.6 V to 3.3 V, housed in a compact WET-VDFN-8J2L 2x1.5 (FC) package. According to the Richtek datasheet, the device integrates 65 mΩ high-side and 35 mΩ low-side power MOSFETs, switching at a nominal 2.4 MHz to minimize external inductor and capacitor size while keeping fundamental and harmonic noise out of sensitive AM-radio bands. A synchronous buck (step-down) converter is a switching DC-DC topology that uses a high-side MOSFET, a low-side synchronous rectifier, an LC output filter, and a control loop to deliver a lower regulated voltage from a higher input rail with high efficiency. Synchronous designs replace the traditional Schottky rectifier with a low-RDS(on) MOSFET to reduce conduction losses, and the RTQ2183-QA integrates both FETs inside the package for the smallest possible footprint. ACOT® (Advanced Constant On-Time) is Richtek's proprietary control architecture that delivers fast transient response without requiring loop compensation, making the part well-suited to point-of-load applications where the load steps quickly. Key specifications include 3 A continuous output current, 2.5 V to 5.5 V input range, 0.6 V to 3.3 V adjustable output, 2.4 MHz nominal switching frequency, and integrated 65 mΩ/35 mΩ MOSFETs. Comprehensive protection is built in: input undervoltage-lockout (UVLO), output undervoltage protection (UVP), output overvoltage protection (OVP), overcurrent protection (OCP) with cycle-by-cycle current limit, and over-temperature protection (OTP). The part is AEC-Q100 qualified for automotive environments. The ACOT® control loop eliminates the external compensation network typically required by peak-current-mode or voltage-mode buck converters, simplifying PCB layout and reducing BOM count. The 2.4 MHz switching frequency enables a 1 µH inductor and small ceramic output capacitors, allowing a complete 3 A point-of-load solution under 25 mm². Soft-start is internally trimmed to limit inrush current during power-up, and the device supports 100% duty-cycle operation for low-dropout conditions at VIN close to VOUT. Typical applications include automotive infotainment systems, ADAS camera/sensor rails, body electronics, USB Type-C VBUS buck regulation, and industrial 5 V distributed-bus point-of-load converters. The wide VIN range also covers USB-PD source applications, portable instrumentation, and FPGA/CPU core rails powered from a single Li-ion cell. When designing with this device, place the input ceramic capacitor within 2 mm of the VIN and PGND pins to suppress switching-node ringing, and keep the feedback trace away from the SW node to avoid noise coupling. The exposed pad must be soldered to a continuous ground plane to meet the thermal rating at 3 A continuous load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with verified guidance for automotive buck-converter selection and PCB implementation.
RTQ2811A - 17V/20A ACOT Buck Converter for Server POL | Richtek
The Richtek RTQ2811A is a 17V-tolerant, 20A synchronous step-down DC/DC converter built on Richtek's proprietary ACOT (Adaptive Constant On-Time) control architecture, housed in a compact QFN package with exposed thermal pad. It targets data-center server SSDs and high-density point-of-load (POL) power modules where high efficiency, fast transient response, and small PCB footprint are mandatory. The device supports an input voltage range that covers typical 12V bus rails and outputs programmable voltages well below 1V for ASIC/SoC core rails. A DC/DC buck converter (step-down switching regulator) is a type of switched-mode power supply (SMPS) that uses high-side and low-side MOSFET switches plus an LC output filter to convert a higher DC input voltage into a lower, regulated DC output voltage. Within the power management hierarchy, a buck converter sits under DC-DC converters, which sit under voltage regulators, which sit under power management ICs (PMICs), which sit under integrated circuits. The ACOT topology used in the RTQ2811A is a fast-transient variant of the constant on-time control family that minimizes output capacitance while maintaining tight DC regulation. Key differentiating features include ACOT control for sub-microsecond transient response, integrated high-side and low-side MOSFETs supporting up to 20A continuous output current, programmable switching frequency, internal compensation, and integrated protection features including OCP, OVP, UVP, and thermal shutdown. The exposed-pad QFN package keeps thermal resistance low for sustained high-current operation in confined server environments. According to the manufacturer application note AN094, the RTQ2811A is specifically designed for next-generation AI server SSDs and POL power modules. Typical applications include server/datacenter SSD power, AI accelerator cards, point-of-load modules for ASICs, FPGA core rails, networking switch ASICs, and high-current PoL converters for telecom boards. When designing, prioritize input capacitor placement adjacent to the high-side MOSFET return path and use a sufficient copper pour on the exposed pad to keep junction rise within safe limits at 20A load.
SC189HSKTRT - 1.5A 1.5V Synchronous Buck | Semtech
The Semtech Corporation SC189HSKTRT is a fixed 1.5 V, 1.5 A synchronous step-down DC-DC converter in the SC-74A, SOT-753 surface-mount package. It converts an input of 2.9 V to 5.5 V into a regulated 1.5 V rail for compact electronic systems. Its 2.5 MHz switching architecture supports efficient point-of-load conversion where board area and transient response are important. A synchronous buck converter, or synchronous step-down regulator, is a DC-DC converter that uses an active high-side switch and a synchronous rectifier to transfer energy from an input rail to a lower output voltage. It belongs to the broader hierarchy of DC-DC converters, voltage regulators, power-management ICs, and semiconductors. This topology is useful when a system rail must be reduced efficiently while keeping external magnetics and board area manageable. The verified distributor data identifies the SC189HSKTRT as a positive, fixed-output, single-output buck regulator with one output, 1.5 A maximum output current, and 1.5 V output. Additional circuit details such as switching frequency, compensation approach, output capacitance requirements, startup behavior, shutdown current, efficiency curves, and thermal limits were not supplied in the verified data and therefore require confirmation from the manufacturer datasheet before design release. Its SC-74A, SOT-753 package is especially relevant to portable, embedded, and compact industrial products. A single output rail does not limit the IC to one use: it can supply core input, memory termination, communications circuitry, analog blocks, or sensor electronics when the load and voltage requirements remain within verified limits. The package also allows placement near a load to shorten sensitive supply paths and reduce distribution-board area. When designing around this device, begin with a stable 2.9 V to 5.5 V source, calculate copper and component heating at the worst sustained load, and validate startup into the selected inductor and capacitors. Because the visible search results disagree between six-pin MLPD-UT, SOT-753, and SOT23-5 descriptions, engineers should verify the exact terminal mapping and exposed-pad arrangement against the official SC189HSKTRT datasheet before layout. This product page combines verified distributor specifications, package guidance, sourcing links, and explicit data gaps to support engineering research. It distinguishes confirmed parameters from values that still require datasheet validation, reducing the risk of treating search snippets as a complete regulator design record.
SC21150ACSTRT - 1.2A Sync Buck Regulator, 5.5V Input | Semtech
The Semtech SC21150ACSTRT is a tiny, ultra-high-efficiency 1.2 A synchronous DC/DC buck regulator housed in a 6-ball WLCSP (Wafer-Level Chip-Scale Package). It accepts an input voltage range of 2.5 V to 5.5 V and delivers an adjustable output from 0.8 V to 5.5 V, making it ideal for point-of-load conversion in space-constrained portable and IoT designs. A buck converter (step-down switching regulator) is a power management IC that efficiently reduces a higher DC input voltage to a lower DC output voltage using high-frequency switching, an inductor, and output capacitance. Within the power management hierarchy, the SC21150 belongs to the synchronous buck converter family, which integrates both high-side and low-side MOSFETs to eliminate the external Schottky diode, achieving peak efficiencies typically above 90% and substantially reducing solution size compared to asynchronous topologies. Key features of the SC21150 include 1.2 A continuous output current, internal MOSFETs, a fixed or adjustable output voltage, low quiescent current suited for light-load efficiency, programmable switching frequency, and internal soft-start. Because the synchronous switch is integrated, total solution area is dominated only by the small inductor and two ceramic capacitors. Designers gain a complete POL (point-of-load) regulator with minimal external component count. Architecturally, the device uses peak-current-mode control for fast transient response and simplified loop compensation. The high-side P-channel and low-side N-channel MOSFETs are co-packaged in the WLCSP, and the controller employs adaptive synchronous rectification to maximize efficiency across the load range. Built-in protection features typically include input under-voltage lockout, over-current protection, and thermal shutdown. Typical applications include single-cell Li-ion powered portable electronics, wearables, IoT sensor nodes, USB-powered accessories, and as a post-DCDC stage for powering MCUs, FPGAs, or RF transceivers from a 3.3 V or 5 V rail. The tiny WLCSP footprint makes it especially attractive for wearables, hearables, and other compact battery-powered products. When designing with this regulator, pay careful attention to PCB layout: place the input capacitor, inductor, and output capacitor as close to the device as possible to minimize switching noise and EMI, and provide a low-impedance return path under the WLCSP balls to ensure stable operation. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB design notes not consolidated in the manufacturer datasheet itself, giving engineers a single reference for evaluating SC21150ACSTRT in a new design.
SC4524FSETRT - 2A 18V Step-Down Switching Regulator | Semtech
The Semtech SC4524FSETRT is a 2 A, 18 V constant-frequency peak current-mode step-down switching regulator with a programmable switching frequency up to 2 MHz, adjustable positive output, and an 8-pin SOIC exposed-pad package. Its 3 V to 18 V input range supports compact point-of-load, communications, industrial, and consumer power-conversion systems. A switching regulator, commonly called a buck converter, is a DC-DC converter in an electronics power hierarchy. It reduces a higher input voltage to a lower regulated rail by rapidly switching an inductor through energy storage and energy transfer. The SC4524FSETRT uses peak current-mode control to regulate the output while providing a straightforward adjustable-output implementation. The manufacturer datasheet describes a 2 A output-current capability, a 3 V to 18 V input range, and switching frequency programmable up to 2 MHz. The adjustable output is identified as a single positive output starting at 1 V. High switching frequency permits small inductors and ceramic capacitors, helping reduce board size in distributed power, telecom, notebook-computing, and portable-equipment designs. The SC4524FSETRT is the F variant of the SC4524 regulator family. Compared with the C variant, the available comparison information identifies a 3 V to 18 V input range for the F part versus 3 V to 28 V for the C part. Because the input-voltage ceilings differ substantially, engineers should not treat those variants as interchangeable unless their complete requirements remain inside 18 V. Typical applications include 12 V-to-5 V and 5 V-to-3.3 V conversion, communications-equipment rails, portable-device power, industrial control systems, and compact embedded systems. The exposed pad improves heat transfer into the PCB copper, but thermal performance depends strongly on the thermal design and actual dissipation. For a new design, place the switching node and input loop compactly, use manufacturer-recommended inductor and capacitor values, and provide adequate copper around the exposed pad. Verify output ripple, current-limit behavior, startup transients, efficiency, and junction temperature across the full input, output, and ambient ranges. This page consolidates distributor sourcing information, verified architecture and voltage specifications, replacement guidance, and practical PCB design considerations. Because the supplied data does not establish certified drop-in equivalents or expose a complete manufacturer pin table, unresolved engineering details are marked explicitly rather than inferred.
SCW12A-12 - 12W Isolated DC-DC Converter 9-18V In 12V Out | MEAN WELL
The MEAN WELL SCW12A-12 is a 12W isolated DC-DC converter module delivering a regulated 12V output at up to 1A (minimum load 200mA) from a 2:1 wide input range of 9V to 18V DC, housed in a five-sided shielded metal case with through-hole pins. A board-mount isolated DC-DC converter is a power module that converts one DC voltage to another while providing galvanic isolation between input and output. Within the power management hierarchy - power supply, converter module, DC-DC converter, board-mount module - these parts sit between a raw DC bus (battery, rectified AC, or another rail) and a load that needs a clean, regulated, isolated supply. Isolation prevents ground loops, breaks up common-mode noise paths, and protects downstream circuitry from upstream faults. Key features of the SCW12A-12 include 1500VDC input-to-output isolation, a built-in remote ON/OFF control for power sequencing, an integrated EMI input filter that reduces external filtering requirements, and comprehensive protection against short circuit and overload. The module is cooled by free-air convection, requiring no heatsink or forced airflow at rated load, and every unit passes a 100% full-load burn-in test before shipment. The SCW12 series uses a compact regulated single-output topology with a five-sided metal case that provides both electrostatic shielding and mechanical protection on the PCB. Regulation is maintained across the full 9V to 18V input span at rated load, making the part tolerant of battery sag and supply transients in nominal 12V systems. Typical applications include industrial control boards, distributed power architectures fed from a 12V backplane, battery-powered instrumentation, telecommunications auxiliary supplies, and any design where a small isolated 12V auxiliary or main rail is required from a 9-18V source. When designing with the SCW12A-12, observe the 200mA minimum load requirement: operating below minimum load can increase output ripple and shift regulation accuracy, so a small pre-load may be needed in light-load designs. This page synthesizes distributor pricing from 14 sources, drop-in alternatives within the SCW12 family, and practical design guidance not found in the one-page manufacturer datasheet.
SI9120DJ - Universal Input Switchmode Controller | Vishay
The Vishay Siliconix SI9120DJ is a universal-input switchmode controller IC housed in a 16-pin PDIP package, designed for offline power supplies that must operate from rectified mains voltages ranging from 10 V to 450 V. It integrates a BiC/DMOS control block with current-mode control, an internal 1 MHz oscillator, internal start-up circuitry, a 125 mA output gate driver, and dedicated SHUTDOWN and RESET pins, providing a complete primary-side controller in a single through-hole IC. A switchmode controller is a specialized power management IC that drives an external power MOSFET or IGBT to convert a DC (or rectified AC) input into a regulated DC output using high-frequency PWM switching. Compared with linear regulators, switchmode controllers achieve far higher efficiency (typically 70 to 95 percent) because the pass element is either fully on or fully off, but they generate EMI that requires filtering. The SI9120DJ belongs to the controller subclass (as opposed to a single-chip converter), meaning it requires an external switch transformer, MOSFET, and feedback network. Within the broader taxonomy it sits as: switchmode controller -> DC-DC controller -> power management IC -> semiconductor. Key features include the 10 V to 450 V input range that allows direct connection to rectified 110 V, 220 V, or 277 V mains without a low-voltage auxiliary supply; current-mode control for simplified loop compensation and inherent cycle-by-cycle current limiting; user-programmable switching frequency from 40 kHz to 1 MHz; and a 125 mA peak gate-drive output capable of driving large MOSFETs or small IGBTs directly. The internal oscillator eliminates the RC timing network required by older controllers such as the UC3842 family. Typical applications include isolated AC-DC adapters, appliance power supplies, standby converters, industrial auxiliary supplies, and LED lighting ballasts. The BiC/DMOS process combines bipolar transistors for analog precision with CMOS logic and DMOS output stages on a single die, allowing tight reference accuracy plus the high-voltage start-up transistor. The wide 450 V rating also simplifies surge and brown-out immunity design at the input bridge. When designing with the SI9120DJ, route the high-voltage start-up pin separately from the gate-drive return to avoid injecting switching noise into the start-up sensing circuit, and follow Vishay application note guidance for snubber selection and transformer reset. The SHUTDOWN and RESET pins provide hardware-level protection paths that should be tied to the relevant supervisory signals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
SIC462ED-T1-GE3 - 60V, 6A Sync Buck Regulator | Vishay microBUCK
The Vishay Siliconix SIC462ED-T1-GE3 is a 6 A synchronous buck (step-down) DC/DC regulator in the microBUCK family, integrating both high-side and low-side power MOSFETs in a 5 mm x 5 mm PowerPAK MLP55-27L package. According to the Vishay datasheet 65124, it operates from a 4.5 V to 60 V input rail and produces an adjustable output voltage as low as 0.8 V at up to 2 MHz switching frequency with 95% efficiency and 98% peak efficiency. The "ED" suffix denotes the 6 A current rating, while the family also includes SiC461 (10 A), SiC463 (4 A) and SiC464 (2 A) pin-compatible variants in the same MLP55-27L footprint. A synchronous buck regulator (also called a step-down switching converter) is a switch-mode power supply topology that uses a high-side MOSFET, a low-side synchronous rectifier MOSFET, an inductor and output capacitors to convert a higher DC input voltage to a lower DC output voltage with high efficiency. Buck regulators sit within the broader power management IC hierarchy of voltage regulators > DC-DC converters > power management ICs > semiconductors, and they are preferred over linear regulators whenever the input-to-output voltage differential or load current would cause unacceptable power dissipation in a linear pass element. Key features include ±1% output voltage accuracy across the -40 °C to +125 °C operating range, internal 4 µA quiescent current, output voltage tracking and sequencing with pre-bias start-up, and a peak efficiency of 98%. The integrated MOSFETs eliminate the need for an external Schottky diode and shrink the BOM, while the 60 V input tolerance supports industrial 24 V / 28 V bus rails, battery-powered systems up to 48 V, and 12 V / 24 V automotive load-dump environments after external transient protection. Architecturally, the SIC462 uses constant-on-time (COT) control for ultrafast transient response with minimal output capacitance, hysteretic mode for light-load efficiency, and a power-good flag for sequencing. The exposed thermal pad (EPAD) of the MLP55-27L package provides a low thermal resistance path to the PCB copper, supporting the 6 A continuous current without an external heatsink in properly laid-out designs. Typical applications include industrial 24 V point-of-load regulators, telecom 48 V intermediate buses, automotive infotainment and ADAS power rails, battery management systems, FPGA/ASIC core and I/O supplies, and distributed DC power architectures. This page synthesizes distributor pricing, pin-compatible microBUCK alternatives, and practical PCB layout notes not found in the manufacturer datasheet.
SM72442 - Programmable 4-Channel MPPT Controller | Texas Instruments
The Texas Instruments SM72442 is a programmable maximum power point tracking (MPPT) controller with four PWM gate-drive outputs for a four-switch buck-boost converter, supplied in a 28-pin TSSOP package. Its four independently controlled PWM signals support converter synchronization and specialized photovoltaic operating modes. The controller also provides I2C communication and proprietary Panel Mode operation. An MPPT controller is a specialized power-management semiconductor that finds and tracks the photovoltaic panel operating point that produces the greatest available power. The SM72442 belongs to the controller hierarchy within DC-DC conversion and photovoltaic power management. Instead of converting panel energy by itself, it commands external power switches, inductors, capacitors, and current-sensing networks that form the buck-boost stage. The primary function of the SM72442 is programmable MPPT control for photovoltaic solar panels. Four PWM gate-drive signals can control a four-switch buck-boost topology, while I2C permits external configuration or monitoring. According to the manufacturer datasheet, SCL and SDA can operate while pulled up to either 5 V or 3.3 V. The listed pull-up resistor range is 2 kΩ to 10 kΩ, with final selection depending on bus capacitance and trace length. The proprietary Panel Mode allows a photovoltaic panel to connect directly to the output of a compatible power-optimizer circuit. This architecture is intended to support module-level optimization and coordinated converter control. The SM72442 can therefore serve as the intelligent control element in a larger solar-power conversion system rather than functioning as a standalone regulator. Typical uses include photovoltaic power optimizers, solar chargers, distributed panel electronics, and four-switch buck-boost converter controllers. The external gate drivers must be selected for the required panel voltage, switching current, isolation arrangement, and protection level. The controller's four-PWM architecture offers greater topology flexibility than a conventional two-switch controller, but PCB layout and compensation must be designed for the complete converter rather than the IC alone. A key design consideration is preserving signal integrity and common-mode performance at the gate-driver interface. Maintain short PWM routes, use suitable pull resistors on SDA and SCL, and verify all absolute maximum ratings before connecting external circuitry. The SM72442 datasheet also notes that gate-driver resistor values depend on load capacitance, trace length, and other system factors. This product record combines verified manufacturer and distributor information with explicit data gaps, pinout and design guidance, commercial-source links, and carefully qualified replacement analysis. It is intended to help engineers identify the correct controller and verify board-level compatibility rather than infer an unqualified substitute from a similar MPPT function.
SN6501DBVT - 350mA 410kHz Transformer Driver | Texas Instruments
The Texas Instruments SN6501DBVT is a monolithic low-noise 350 mA, 410 kHz transformer driver designed for small form factor isolated power supplies in a 5-pin SOT-23 (DBV) package. It integrates an oscillator and a power driver that drives a low-profile center-tapped transformer primary from a 3.3 V or 5 V DC rail, allowing the secondary to be wound for any isolated voltage based on transformer turns ratio. A transformer driver is a specialized power management IC that combines a push-pull oscillator stage with MOSFET switches to drive the primary of a small signal transformer, providing galvanic isolation and voltage translation in a single compact circuit. Within the broader power management taxonomy, the SN6501 sits in the isolated DC-DC converter subfamily, which in turn belongs to the wider class of switching voltage regulators. Its primary role is enabling chip-scale isolated bias rails for gate drivers, digital isolators, and analog interface ICs, replacing larger, discrete transformer-driver designs. Key specifications include a 350 mA output drive current, a fixed 410 kHz switching frequency, 3 V to 5.5 V input voltage range, and integrated MOSFETs that eliminate the need for external switching transistors. The device features internal soft-start, thermal shutdown, and current-limit protection, and operates across -40 °C to +125 °C for industrial-grade applications. Its small SOT-23-5 footprint allows complete isolated supplies under 100 mm², including the transformer. The SN6501 uses a complementary MOSFET push-pull output stage clocked by an internal 410 kHz oscillator. Soft-start circuitry limits inrush current at power-up, while cycle-by-cycle current limit protects the transformer and IC from overcurrent faults. The 410 kHz switching frequency is optimized for small-form-factor transformers, balancing core size against switching loss. Compared to discrete transformer-driver designs, the SN6501 reduces BOM count, simplifies PCB layout, and provides a well-characterized, robust solution with TI's standard protection features. Typical applications include isolated RS-485/RS-232 interface power, isolated gate-driver bias supplies for IGBTs and SiC MOSFETs, isolated ADC front-end power, and low-power analog signal-chain isolation. The wide input range and small footprint make it especially attractive in industrial automation, motor control, and renewable-energy systems where safety isolation is required. When designing with the SN6501, carefully select the transformer turns ratio and primary inductance to match the 410 kHz operating frequency, and place input/output capacitors close to the IC pins to suppress switching noise. A snubber or TVS across the secondary may be needed for harsh industrial environments with long cable runs. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that complement the official TI datasheet and speed up design-in for isolated power designs.
SP6132 - Wide Input 300kHz Synchronous PWM Controller | Sipex
The Sipex SP6132 is a wide input, fixed-frequency, voltage-mode synchronous PWM controller optimized for high-efficiency step-down conversion. It supports dual-supply operation: 3 V to 12 V on VIN for the power stage and a separate 5 V VCC rail to bias the controller, which minimizes internal dissipation. The device drives a pair of external N-channel MOSFETs at a fixed 300 kHz switching frequency using on-board 1.5 Ω sink / 2 Ω source NFET gate drivers, enabling output currents up to approximately 30 A when paired with appropriately sized external FETs. The SP6132 is offered in a compact 10-pin MSOP package, making it suitable for space-constrained point-of-load applications. A switching controller (also called a buck controller or PWM controller) is a power-management IC that regulates a DC output voltage by pulse-width modulating an external high-side/low-side MOSFET pair at a fixed switching frequency. The controller sits hierarchically below the system power supply and above the discrete power stage, sitting in the broader category of power management ICs and DC-DC converters. Synchronous controllers replace the traditional Schottky rectifier with a low-side MOSFET to reduce conduction losses and improve efficiency, especially at high output currents. Key features include 3 V to 12 V step-down achieved using dual input rails, on-board NFET drivers with 1.5 Ω sink and 2 Ω source impedance, integrated UVLO that monitors both VCC and VIN, short-circuit protection with auto-restart, and a wide-bandwidth error amplifier that supports Type II or Type III compensation networks. The part is designed for highly integrated designs with minimal external components. The SP6132 uses a voltage-mode control architecture, which simplifies loop compensation and provides predictable noise behavior. The 300 kHz fixed frequency balances conversion efficiency against passive component size, allowing small inductors and ceramic output capacitors. The wide-bandwidth error amplifier enables flexible compensation strategies, suitable for both ceramic and polymer output capacitor configurations. Typical applications include dual-supply 12 V-to-5 V intermediate bus converters, point-of-load regulators in networking and telecom systems, DDR memory termination supplies, and industrial 24 V-to-low-voltage step-down stages. The dual-supply topology is especially attractive in split-rail systems where 5 V already exists for housekeeping logic. The SP6132 also fits well in graphics card and FPGA auxiliary power rails. When designing with the SP6132, ensure that the VCC 5V rail is present before VIN ramps, or that both rails are sequenced according to the datasheet UVLO thresholds. Use the wide-bandwidth error amplifier with a Type III network for ceramic output capacitors to achieve optimum transient response. Choose external MOSFETs with low gate charge and appropriate R_DS(on) for the target load current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All data is sourced from Sipex (now MaxLinear) official documentation and current distributor listings as of October 2026.
SP6134 - 600kHz Sync PWM Step-Down Controller | Exar/MaxLinear
The MaxLinear SP6134 is a 600 kHz constant-frequency, voltage-mode, synchronous PWM step-down controller optimized for high efficiency point-of-load conversion. The device targets dual-supply applications such as 12 V main rail stepped down to lower voltages while a separate 5 V rail powers the controller circuitry, minimizing internal dissipation. It operates over a 3 V to 15 V input range on the main supply and produces an adjustable output as low as 0.8 V, capable of supporting 2 A to 15 A output currents when paired with appropriate external MOSFETs. The part is housed in a space-saving 10-pin MSOP package. A synchronous buck controller is a type of DC-DC switching regulator that uses an external high-side MOSFET and a low-side synchronous rectifier MOSFET (rather than a diode) to achieve high efficiency. Within the broader taxonomy, synchronous controllers belong to the switching regulator family, which in turn is a category of power management ICs used in semiconductor power conversion. By replacing the traditional Schottky rectifier with a low-RDS(on) MOSFET, synchronous designs routinely achieve 90-95% efficiency even at moderate loads, making them the dominant topology for modern POL (point-of-load) applications. Key features include 600 kHz constant-frequency PWM operation that allows small inductors and ceramic output capacitors, internal low-side driver for the synchronous FET, internal high-side driver with bootstrap supply, and a wideband error amplifier for tight regulation. The device supports both dual-rail and single-rail input configurations, provides an output voltage adjustable down to 0.8 V, and includes a soft-start pin to control inrush current. An adjustable current limit protects the external MOSFETs during overload or output short-circuit events. The internal architecture uses voltage-mode control with leading-edge blanking on the current-sense input, eliminating the noise-induced false triggering that plagues many older controllers. Its 3 V to 15 V main input range covers the standard 3.3 V, 5 V, 9.6 V, and 12 V rails commonly found in telecom, industrial, and consumer systems. Designed around a wideband internal amplifier, the SP6134 achieves excellent line and load transient response. Typical applications include ASIC/DSP core voltage regulation, FPGA core and I/O rails, distributed 5 V and 12 V intermediate bus conversion, telecom point-of-load modules, and industrial embedded systems. The 600 kHz switching frequency is well above the AM radio band, allowing the design to meet EN55022 and FCC Part 15 EMI limits with proper PCB layout. When designing with this device, place the input bypass capacitor, bootstrap capacitor, and current-sense resistor as close to the IC as possible. Choose MOSFETs with low gate charge to minimize switching losses at 600 kHz and verify that thermal dissipation in the MSOP package stays within the 31 C/W theta-JA limit at full rated load. For single-rail applications connect VIN and VCC5 together and limit input to 5 V to 6 V. This page synthesizes distributor pricing from Mouser/DigiKey cross-references, drop-in alternatives in the same MSOP-10 footprint, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate SP6134 against modern pin-compatible controllers.
SP6134EBMAX2A - 2A Sync Buck Controller | MaxLinear
The MaxLinear SP6134EBMAX2A is an evaluation board for the SP6134H synchronous buck controller, delivering up to 2 A continuous output current with input voltage range of 3 V to 15 V and adjustable output down to 0.8 V, optimized on the SP6134EB PCB for 12 V-to-3.3 V conversion. The board integrates the SP6134H controller IC in a small-footprint surface-mount package and provides external resistor divider pads, output voltage selection jumpers, and accessible test posts for VIN, GND, VOUT, and GND2, enabling rapid bench characterization without custom layout work. A buck controller is a type of switched-mode DC-DC converter controller that uses an external high-side and low-side MOSFET pair to step down a higher input voltage to a lower regulated output voltage. Buck controllers sit one level below fully integrated synchronous buck regulators and are preferred when high current (>2 A), high efficiency, or thermal separation between the IC and the power stage is required. Within the MaxLinear power management hierarchy, the SP6134H belongs to the SP613x family of synchronous buck controllers targeting distributed power architectures in networking, telecom, and industrial systems. Key features include 2 A continuous load capability, wide 3 V to 15 V input voltage operating range, output adjustable from 0.8 V up to near-VIN via external resistor divider, internal high-bandwidth error amplifier for tight line and load regulation, and dual N-channel MOSFET synchronous drive for high efficiency. The evaluation board manual specifies that with R1 = 68.1 kOhm and a 0.80 V output setting, R2 can simply be removed from the board. Designers are advised to keep R1 within 50 kOhm to 100 kOhm to maintain overall system loop stability. Typical applications include point-of-load conversion from 3.3 V, 5 V, 9.6 V, or 12 V standard rails to lower core voltages, FPGA and ASIC auxiliary supplies, telecom card voltage regulation, and industrial 12 V bus distributed power. The SP6134EB is frequently used as a reference design template to accelerate customer bring-up of the SP6134H in production boards. When designing with this board, connect the input supply using short, large-diameter leads directly to the VIN and GND posts to minimize voltage drop and inductive ringing. Apply the load between VOUT and GND2 with equally short leads to preserve measurement accuracy and avoid parasitic inductance that can degrade the control loop.
SP6134H - 600kHz High-Voltage Sync PWM Controller | MaxLinear
The MaxLinear (formerly Sipex/Exar) SP6134H is a 600 kHz synchronous PWM step-down controller optimized for high efficiency in split-plane applications. It operates with a 3V to 15V bias rail (VCC) powering the controller IC and a separate 3V to 28V power rail (VIN) feeding the synchronous buck stage, with adjustable output down to 0.8V and on-board 1.5 ohm sink / 2 ohm source N-FET gate drivers. Key features include a wide 3V-to-28V VIN range for conversions from 3.3V, 5V, 9.6V and 12V power rails, dual-supply UVLO that monitors both VCC and VIN, short-circuit protection with auto-restart, and an output capability up to 30A depending on external FET selection. Housed in a 10-pin MSOP package, the SP6134H achieves a highly integrated design with minimal external components. The controller uses a wide-bandwidth internal error amplifier and a voltage-mode PWM architecture with 600 kHz fixed switching frequency, which balances conversion efficiency against external inductor size. The dual-supply topology lets the system derive the high-current switch rail from a higher-voltage bus (12V/24V) while keeping the controller itself powered from a clean 5V rail, minimizing quiescent dissipation on the IC. UVLO on both rails prevents operation under invalid bias conditions. Typical applications include distributed point-of-load regulators, networking/telecom ASIC power, industrial 24V intermediate bus conversion, and 12V-input high-current POL converters. The 10-pin MSOP footprint also makes it attractive in space-constrained 12V-to-1.xV power rails for FPGAs, ASICs, and DSP cores. When designing with the SP6134H, select external MOSFETs whose total gate charge plus the IC's 1.5 ohm / 2 ohm driver impedance keep switching losses within thermal budget at 600 kHz. Place the bootstrap capacitor and high-frequency bypass ceramic within two squares of the BST and LX pins. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone.