بەرهەمەکان (46,000+)

AD524CE - Precision Instrumentation Amplifier | Analog Devices
AD524CE

AD524CE - Precision Instrumentation Amplifier | Analog Devices

The Analog Devices AD524CE is a precision monolithic instrumentation amplifier intended for high-accuracy data-acquisition signal chains. The AD524 family provides rail-to-rail operation, low offset voltage, low offset-voltage drift, and low noise for precision high-gain measurements. The family supports a wide supply range and gains up to 1000, reaching a 25 MHz gain-bandwidth product at a gain of 1000. AD524CE is supplied in a ceramic DIP package with an extended-temperature identification code. An instrumentation amplifier is a differential-input amplifier designed to amplify the voltage difference between two inputs while rejecting common-mode signals. It belongs to the operational-amplifier hierarchy and is commonly used where sensors produce small differential signals superimposed on larger common-mode voltages. In a typical signal chain, a sensor connects to the amplifier inputs, the instrumentation amplifier provides selectable gain, and the output is routed to an ADC or data-conversion system. The AD524 family is characterized by precision DC specifications and low noise. Its rail-to-rail behavior supports operation across the available supply range, while the wide supply range provides flexibility across industrial, instrumentation, and test systems. Gains of 1 through 100 are supported by the AD524 family, with a 25 MHz gain-bandwidth product specified at a gain of 1000. Output slew rate is 5 V/µs, and settling to 0.01% takes 15 µs for gains from 1 through 100. The AD524 uses a precision monolithic implementation to provide accurate gain and low offset behavior. Its low offset voltage and low offset-voltage drift reduce measurement errors that could otherwise change with temperature or operating conditions. The combination of rail-to-rail operation, low noise, and stable DC characteristics makes the family appropriate for bridge sensors, strain gauges, pressure transducers, and other precision measurement circuits. Typical applications include industrial process measurement, laboratory data acquisition, sensor-interface boards, medical instrumentation, and test equipment. In a bridge or strain-gauge circuit, the differential output from the sensor is amplified while common-mode excitation and ground-potential differences are rejected. The AD524 can also precede an ADC when a small sensor signal requires additional gain and analog signal conditioning. Designers should verify the exact AD524CE pinout, supply limits, gain configuration, input common-mode range, and recommended external components against the Analog Devices AD524 datasheet before layout. Input and reference networks should use tight-tolerance resistors when gain accuracy is important, and the circuit should minimize board leakage and thermal gradients across sensitive inputs. This page combines family-level performance, package information, sourcing guidance, comparison criteria, and practical application notes. It also distinguishes verified drop-in options from family members that use different packages, helping engineers make a replacement decision based on actual board compatibility rather than function alone.

RFQ پەیوەندی
AD5252BRUZ50 - Dual 256-Tap 50kΩ I2C EEMEM DigiPOT | ADI
AD5252BRUZ50

AD5252BRUZ50 - Dual 256-Tap 50kΩ I2C EEMEM DigiPOT | ADI

The Analog Devices AD5252BRUZ50 is a dual-channel, 256-position, I2C-compatible, nonvolatile memory (EEMEM) digital potentiometer (DigiPOT) with 50 kΩ end-to-end resistance, supplied in a 14-lead TSSOP (RU-14) package. The BRUZ50 suffix indicates the I2C slave address variant and 50 kΩ nominal resistance. Each channel provides 256 resistive steps with linear taper, ±20% resistance tolerance, and on-chip EEPROM that stores wiper position with write-protect, retaining settings through power cycles. What is a digital potentiometer? A digital potentiometer (DigiPOT) is a solid-state, digitally controllable variable resistor that emulates the wiper action of a mechanical trimpot or potentiometer. DigiPOTs sit within the broader hierarchy of programmable resistors and integrated mixed-signal ICs, communicating via serial interfaces such as I2C or SPI. Compared to mechanical potentiometers, DigiPOTs eliminate physical wear, allow remote/automated adjustment, and integrate memory for nonvolatile setpoint storage. Key features include 256 positions per channel (8-bit resolution), 100 kΩ EEMEM endurance with write-protect, I2C-compatible 2-wire serial interface, predefined linear increment/decrement commands, ±6 dB step change commands, synchronous or asynchronous dual-channel update, and selectable slave addresses via AD0/AD1 pins (up to 4 devices on one bus). The RDAC register provides direct wiper programming for real-time adjustment. The AD5252 architecture pairs two RDAC resistor arrays with EEMEM, a precision bandgap-derived reference, and an I2C slave interface. The wiper resistance, wiper-on-resistance matching, and low temperature coefficient suit instrumentation, audio, and industrial control applications where long-term setting stability is required. Typical applications include LCD display brightness and contrast control, mechanical potentiometer replacement, programmable gain amplifiers, programmable filters and delays, transducer calibration, audio volume control, and RF bias adjustment. The I2C interface allows host MCU control, while the nonvolatile memory preserves calibration data across power cycles. When designing with this device, observe the absolute maximum VDD of 7 V, use 0.1 µF decoupling close to VDD/GND, and respect the dual-supply mode requirement of ±2.25 V to ±2.75 V or single-supply 2.25 V to 5.5 V. EEMEM writes require tWR (write cycle time) per the manufacturer datasheet; verify timing when programming in-loop. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the standalone manufacturer datasheet, accelerating component selection and PCB bring-up.

RFQ پەیوەندی
AD5258BRMZ1-R7 - 1kΩ 64-Tap I²C Nonvolatile DigiPot | ADI
AD5258BRMZ1-R7

AD5258BRMZ1-R7 - 1kΩ 64-Tap I²C Nonvolatile DigiPot | ADI

The Analog Devices AD5258BRMZ1-R7 is a 1 kΩ end-to-end, 64-position, nonvolatile digital potentiometer (DigiPOT) in a compact 10-pin MSOP (3 mm × 4.9 mm) package. It performs the same electronic adjustment function as a mechanical potentiometer or variable resistor, but with enhanced 6-bit resolution (64 taps) and solid-state reliability, while exposing an I²C-compatible digital interface for wiper control and on-chip EEPROM read/write. A digital potentiometer is a solid-state, digitally controlled variable resistor that emulates the three-terminal behavior of a mechanical pot (RH, RL, RW). DigiPOTs belong to the broader data-conversion signal-conditioning family, sitting architecturally between mechanical passives and programmable analog ICs: a fixed resistor string is divided by an analog switch network, and a wiper switch taps a node set by an on-chip register. Compared with mechanical pots, DigiPOTs offer nonvolatile wiper memory, unlimited endurance, microsecond settling, and immunity to vibration and contamination. Key features of the AD5258 include 64 positions with ±1 LSB DNL (differential non-linearity), end-to-end resistance options of 1 kΩ / 10 kΩ / 50 kΩ / 100 kΩ stored in EEPROM with 0.1 % tolerance accuracy, a separate VLOGIC pin for level-shifted interface flexibility (1.8 V–5.5 V), software write-protect, dual address decode pins (AD0/AD1) allowing up to four AD5258s on one bus, and a power-on EEPROM refresh in <1 ms. Wiper resistance is 75 Ω typical, and operating temperature spans −40 °C to +125 °C. Architecturally, the AD5258 uses a CMOS resistor ladder with NMOS wiper switches and an integrated EEPROM cell for each tap, controlled by an I²C-compatible serial interface. The internal charge pump generates the gate drive required for low-distortion analog signal passing in both resistor-divider and rheostat configurations. This makes it suitable for both DC bias trims and AC audio-grade signal paths up to a few hundred kilohertz. Typical applications include LCD backlight brightness and contrast trim, audio attenuation and volume control, programmable power-supply margining, gain trimming for instrumentation amplifiers, sensor calibration in thermocouple/HE platforms, and mechanical-potentiometer replacement in industrial and instrumentation designs where vibration, dust, or operator variability would compromise a mechanical trimmer. Design consideration: for AC audio use, place the DigiPOT inside the feedback network of an op-amp (virtual-ground mode) to remove wiper-resistance non-linearity from the signal path; for DC trim, a two-terminal rheostat connection is acceptable and simplifies routing. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone, with all specifications cross-checked against the official AD5258 datasheet.

RFQ پەیوەندی
AD5258BRMZ1-RL7 - 1kΩ 64-Tap I2C Nonvolatile DigiPot | ADI
AD5258BRMZ1-RL7

AD5258BRMZ1-RL7 - 1kΩ 64-Tap I2C Nonvolatile DigiPot | ADI

The Analog Devices AD5258BRMZ1-RL7 is a nonvolatile, I²C-compatible 64-position digital potentiometer with 1 kΩ end-to-end resistance, housed in a compact 10-pin MSOP (RMZ) package. It performs the same electronic adjustment function as a mechanical potentiometer, but with enhanced resolution, solid-state reliability, and digital control of the wiper position. The wiper setting is stored in internal EEPROM and is automatically recalled on power-up, eliminating the need for re-initialization after a power cycle. A digital potentiometer (DigiPot or RDAC) is a solid-state variable resistor whose wiper position is set by a digital command rather than a mechanical actuator. DigiPots sit in the hierarchy: digital potentiometer → programmable resistor → data-conversion/peripheral IC → mixed-signal semiconductor. They replace mechanical trimmers in volume-production designs where software-driven calibration, remote adjustment, or dynamic trimming is required. Key specifications of the AD5258BRMZ1-RL7 include 64 wiper positions (6-bit resolution), a 1 kΩ nominal end-to-end resistance with ±0.1% tolerance stored in EEPROM, a 2-wire I²C-compatible serial interface, an auxiliary VLOGIC pin for mixed-voltage I/O, and software write-protect. Power-on EEPROM refresh is <1 ms, enabling rapid system startup. End-to-end resistance options in the family cover 1 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ. The internal architecture combines a precision thin-film resistor ladder with CMOS transmission-gate switches and a nonvolatile EEPROM shadow register. The I²C address is selectable via the AD0 pin, allowing two devices on the same bus. Per the AD5258 datasheet, current between Wiper W and Terminal B in the zero-scale state must be limited to a maximum pulse current of 20 mA to avoid degradation of the internal switch contact. Typical applications include LCD backlight brightness control, contrast and bias adjustment on displays, programmable gain amplifiers, RF power-detector calibration, audio volume control, and post-production trimming of precision sensors. Designers typically pair the AD5258 with a low-offset op-amp (e.g., AD8628) when used as an in-circuit trim element. When designing with the AD5258, add a 0.1 µF bypass capacitor close to VDD and respect the 20 mA wiper current limit. Note that DigiPots are not intended for high-current or high-voltage loads; they are optimized for signal-level adjustment and bias-setting roles in low-power analog paths. This page synthesizes distributor pricing, drop-in alternatives from the same MSOP-10 footprint family, and practical design notes that go beyond the manufacturer's datasheet, giving engineers a faster path from selection to qualified BOM line item.

RFQ پەیوەندی
AD5258BRMZ10-R7 - 10kΩ 64-Tap I2C Nonvolatile DigiPOT | ADI
AD5258BRMZ10-R7

AD5258BRMZ10-R7 - 10kΩ 64-Tap I2C Nonvolatile DigiPOT | ADI

The Analog Devices AD5258BRMZ10-R7 is a 10 kΩ, 64-position, nonvolatile digital potentiometer (DigiPOT) housed in a compact 10-pin MSOP package with I²C-compatible interface. It provides 1 circuit of programmable resistance from end-to-end 10 kΩ with 64 tap points, while storing the wiper position in on-chip EEPROM so settings persist through power cycles. A digital potentiometer is a solid-state replacement for a mechanical potentiometer or variable resistor. Within the broader signal-conditioning hierarchy it sits between passive resistive components and active gain stages; its purpose is to provide a digitally controllable resistance ratio (or absolute R) used for gain setting, bias trimming, LCD contrast adjustment, and sensor calibration. The AD5258 family (1 kΩ/10 kΩ/50 kΩ/100 kΩ variants) extends that concept with EEPROM-backed nonvolatile storage, removing the need for software re-initialization at power-up. Key features include: 64-position resolution, I²C-compatible serial interface with address-decode pins AD0/AD1, a VLOGIC pin for mixed-voltage bus compatibility, software write-protect command, end-to-end resistance tolerance stored in EEPROM with 0.1% rcu accuracy, ±6% nominal R-total tolerance, 30 ppm/°C temperature coefficient, and power-on EEPROM refresh time under 1 ms. The device operates from 2.7 V to 5.5 V single supply with low quiescent draw. Internally the AD5258 uses an EEPROM cell for each wiper position and a CMOS transmission-gate ladder network. Each tap is selected through an I²C write to internal registers, and the nonvolatile architecture guarantees that the last programmed wiper position is restored automatically on power-up, eliminating microcontroller boot-time calibration routines. Typical applications include LCD display Vcom adjustment, audio attenuation and volume control, programmable gain amplifiers (PGA) and instrumentation amp gain trim, sensor bias calibration in industrial instrumentation, automotive infotainment and body controllers, and any mechanical-trimmer replacement where reliability, remote adjustment, or automated production calibration is required. When designing with the AD5258BRMZ10, ensure the wiper current does not exceed the datasheet maximum to maintain R-total accuracy. Use the VLOGIC pin when interfacing to 1.8 V or 3.3 V microcontrollers while the potentiometer terminals operate at 5 V, and verify EEPROM write endurance limits if frequent re-programming is expected. This page synthesizes distributor pricing, drop-in AD5258 same-family alternatives, and practical PCB / firmware design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
AD5258BRMZ100 - 100kΩ 64-Tap I2C Nonvolatile DigiPot | ADI
AD5258BRMZ100

AD5258BRMZ100 - 100kΩ 64-Tap I2C Nonvolatile DigiPot | ADI

The Analog Devices AD5258BRMZ100 is a nonvolatile, I²C-compatible 64-position digital potentiometer with 100 kΩ end-to-end resistance, supplied in a 10-pin MSOP (RM suffix) surface-mount package. It integrates EEPROM-backed wiper memory, two address-decoded AD0 pins (supporting up to four devices on one bus), and a separate VLOGIC pin for flexible logic-level interfacing between 2.7 V and 5.5 V domains. A digital potentiometer (DigiPOT) is a solid-state, electronically-controlled variable resistor that replaces a mechanical trimpot. It exposes three terminals — the two fixed end-points (A and B) and a wiper (W) — and lets an MCU step the wiper position through a finite set of taps via a digital interface. DigiPOTs are widely used for gain trimming, LCD contrast biasing, audio attenuation, and sensor calibration where mechanical pots are unreliable or where remote/automated adjustment is required. The AD5258 family occupies the small-footprint, low-cost end of the DigiPOT hierarchy: larger (>256-tap) or higher-voltage parts from ADI (AD5260/AD5290) sit above it; basic mechanical potentiometers and analog rheostats sit below. Key features include 64 tap positions, 100 kΩ nominal end-to-end resistance, ±30 % resistance tolerance, 0.1 % EEPROM-stored tolerance accuracy, <1 ms power-on EEPROM refresh, software write-protect command, and an operating temperature range of −40 °C to +125 °C. The MSOP-10 footprint is only 3 mm × 4.9 mm, making it one of the smallest nonvolatile DigiPOTs on the market. The internal architecture combines a resistor ladder with CMOS switches and a serial EEPROM shadow register. On every power-up the device restores the last-saved wiper position within 1 ms, eliminating the need for software re-initialization. The separate VLOGIC pin isolates the digital interface supply from the analog terminal supply, which simplifies mixed-voltage designs where a 3.3 V MCU controls a 5 V analog rail. Typical applications include LCD contrast and backlight bias adjustment, audio volume control, programmable gain amplifiers, sensor excitation calibration, and mechanical potentiometer/trimpot replacement in industrial, automotive, and instrumentation systems. According to the manufacturer datasheet, ADI has marked the AD5258 family LAST TIME BUY, so designers should plan second-source alternatives now. When designing with this part, treat the analog terminals as low-current signal nodes — the AD5258 is intended for control-loop trimming, not as a power rheostat. Use Kelvin-aware PCB layout when the wiper feeds a high-impedance op-amp input, and observe the absolute maximum terminal voltage of 5.5 V even when the device is unpowered. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving a single reference point for AD5258BRMZ100 sourcing.

RFQ پەیوەندی
AD526ADZ - 16x Programmable Gain Amplifier | Analog Devices
AD526ADZ

AD526ADZ - 16x Programmable Gain Amplifier | Analog Devices

Analog Devices AD526ADZ is a single-ended, monolithic software-programmable gain amplifier with selectable gains of 1, 2, 4, 8, and 16, housed in a 16-lead ceramic DIP package. The device combines an amplifier, resistor network, and TTL-compatible latched gain-control inputs in one monolithic implementation, and it operates without external components. Its 350 kHz bandwidth and ±4.5 V to ±16 V supply range position it between precision low-frequency instrumentation and wider-band signal-conditioning applications. A software-programmable gain amplifier, or SPGA, is a specialized analog signal-conditioning IC that changes its voltage gain through digital control signals. It belongs to the amplifier hierarchy, where an SPGA is more specialized than a fixed-gain operational amplifier and provides a controlled way to normalize signals that arrive over a wide amplitude range. Common system-level roles include sensor-interface amplification, data-converter front ends, laboratory instrumentation, and programmable test and measurement paths. The AD526ADZ provides five binary-programmable gain choices, allowing a system to select sensitivity according to the measured signal level. Gain selection is implemented with latched TTL-compatible control inputs, making the part suitable for processor- or microcontroller-controlled analog front ends. Its single-channel architecture is appropriate when one analog signal must be conditioned at a time, while its monolithic construction eliminates the need for an external switched-resistor network and associated layout complexity. The AD526ADZ has a bandwidth of 350 kHz and supports bipolar supplies from ±4.5 V through ±16 V. These characteristics make it relevant to instrumentation requiring adjustable amplification but not the bandwidth of a high-speed voltage-feedback amplifier. The -55°C to +125°C temperature range also supports industrial and temperature-tolerant signal-chain designs, subject to the complete operating conditions and electrical limits in the manufacturer datasheet. Typical uses include bridge-transducer signal conditioning, programmable audio and communications paths, laboratory measurement front ends, and analog data-acquisition systems. In a data-converter interface, the programmed gain can bring a changing sensor output into a more useful range before conversion. In instrumentation, the five fixed gain selections simplify calibration while avoiding a general-purpose relay or analog switch in the feedback path. Designers should route the latched control signals away from sensitive analog inputs and use a quiet ground and supply arrangement. Because an SPGA contains both analog and digital-control functions, PCB partitioning, input filtering, and supply bypassing influence usable signal-to-noise performance. The pin-description table in the manufacturer datasheet should be used when assigning the 16 package connections and planning the board layout. This page organizes the AD526ADZ specifications, application guidance, package information, and verified drop-in alternatives. It also highlights where the monolithic SPGA simplifies implementation and where bandwidth, supply voltage, and control requirements should be checked before replacing it in an existing instrumentation design.

RFQ پەیوەندی
AD526BD - 16x SPGA, 1-16x Gain | Analog Devices | Instrumentation
AD526BD

AD526BD - 16x SPGA, 1-16x Gain | Analog Devices | Instrumentation

The Analog Devices AD526BD is a single-ended, monolithic software-programmable gain amplifier with digitally selectable gains of 1, 2, 4, 8, and 16, housed in a 16-lead ceramic DIP package. The complete amplifier requires no external gain-setting resistors and includes a resistor network with TTL-compatible latched control inputs. Its maximum gain of 16 makes it suitable for precision instrumentation, sensor conditioning, data acquisition, and industrial measurement systems that need calibrated signal amplification with a compact analog front end. A software-programmable gain amplifier, or SPGA, is a gain-control IC that combines an amplifier with a digitally selectable resistive network. In the signal-chain hierarchy, the AD526BD belongs to the amplifier IC family and specifically to the programmable-gain-amplifier category used ahead of converters, meters, and data-acquisition systems. The latched digital interface allows a processor or controller to select gain while preserving a stable analog operating point during measurement. The AD526 family provides binary gains from 1 through 16 and supports a two-chip cascade mode that extends the available binary gain range to 256. According to the Analog Devices AD526 data sheet, maximum gain error is 0.01% for the C-grade device and 0.02% for the A-grade device, while gain drift over temperature is specified at 0.5 ppm/°C. These characteristics make gain programming useful when one analog input path must accommodate signals with widely different amplitudes. The AD526BD combines its amplifier, internal resistor network, and TTL-compatible latched inputs in one monolithic device. That integration removes the need for external matched gain resistors and reduces circuit area. TTL-compatible control inputs also simplify interfacing with conventional digital logic, although the system designer must still observe the required input timing, supply sequencing, and grounding practices specified in the manufacturer data sheet. Typical applications include bridge-transducer signal conditioning, laboratory measurement front ends, programmable test equipment, industrial process monitoring, and multichannel data-acquisition systems. In a bridge or sensor interface, the selected gain can normalize a small sensor output before it reaches an ADC. The AD526BD can also serve as the first gain stage in a cascaded architecture, where two devices provide higher overall gain while retaining the same family architecture. A key design consideration is signal settling after a gain-code change. Allow sufficient acquisition time for the amplifier and external anti-alias network to settle before sampling the converted signal. Keep sensitive analog traces short, place input and output bypass components close to the device, and use a clean ground reference to minimize errors that could otherwise appear as measurement gain errors rather than as noise from the source. This product page combines the AD526 family architecture, gain-programming behavior, application guidance, and drop-in candidate analysis. It also provides practical selection criteria for engineers deciding between package, grade, temperature-range, and gain-configuration options for precision analog signal chains.

RFQ پەیوەندی
AD526BDZ - 4 MHz Programmable Gain Amp | Analog Devices
AD526BDZ

AD526BDZ - 4 MHz Programmable Gain Amp | Analog Devices

The Analog Devices AD526BDZ is a single-ended, monolithic software-programmable gain amplifier (SPGA) with gains of 1, 2, 4, 8, and 16, a 4 MHz -3 dB bandwidth, and a 24 V/µs slew rate. The device is packaged in a 16-lead ceramic dual in-line package (16-CDIP) and is designed for instrumentation and signal-conditioning systems requiring digital control of analog gain. A software-programmable gain amplifier is a precision analog signal-conditioning device whose gain is selected by digital control signals. In the product hierarchy, an SPGA is a specialized amplifier IC that combines an operational amplifier, a precision resistor network, and digital gain-control logic. This integration allows one amplifier to replace multiple fixed-gain stages while supporting calibration, attenuation, range selection, and programmable measurement systems. The AD526BDZ provides five binary gain selections of 1, 2, 4, 8, and 16. Its TTL-compatible latched inputs allow a microcontroller, parallel interface, or other digital controller to establish the operating gain. Because the amplifier, resistor network, and latched control circuitry are integrated on one monolithic IC, the device requires no external components. This simplifies implementation while reducing the number of discrete precision resistors and switching networks normally required in variable-gain front ends. The AD526 family combines a 4 MHz -3 dB bandwidth with a 24 V/µs slew rate, allowing the amplifier to process signals substantially faster than a low-frequency precision measurement amplifier. Its specified input bias current is 50 pA and input offset voltage is 250 µV. These characteristics make it useful in data-acquisition front ends, sensor signal conditioning, laboratory instrumentation, industrial measurement systems, and analog-to-digital converter input stages. Operation is supported from ±4.5 V to ±16.5 V, corresponding to a total supply span of 9 V to 33 V, and the specified temperature range is -40°C to +85°C. The wide bipolar supply range supports conventional analog and industrial systems while providing headroom for input and output signal excursions. The manufacturer lists the AD526BDZ as active and specifies it for tube packaging in the distributor record. For implementation, connect the analog input to the appropriate signal and return terminals, drive the latched gain-control inputs with compatible logic, and operate the supply rails within the specified limits. Because the gain-control inputs are latched, account for the latch timing when changing gain in a sampled measurement system. Check the input and output operating ranges against the selected gain and supply voltage before applying large signals. This product page combines the AD526 family gain architecture, operating specifications, package information, sourcing guidance, comparison criteria, and practical design notes into a compact engineering reference. It also identifies verified drop-in alternatives while distinguishing package, electrical, lifecycle, and application-selection considerations.

RFQ پەیوەندی
AD526CD - 16-Ceramic-DIP Programmable Gain Amplifier | Analog Devices
AD526CD

AD526CD - 16-Ceramic-DIP Programmable Gain Amplifier | Analog Devices

The Analog Devices AD526CD is a single-ended monolithic software-programmable gain amplifier (SPGA) with selectable gains of 1, 2, 4, 8, and 16, packaged in a 16-pin ceramic DIP. The device integrates the amplifier, resistor network, and TTL-compatible latched inputs, so it requires no external gain-setting components. This combination makes the AD526CD useful for instrumentation systems that need controlled analog gain selected by digital logic rather than a mechanical switch or external resistor network. A programmable gain amplifier is an amplifier whose gain can be changed through control inputs while the signal path remains active. In the broader hierarchy, an SPGA is an amplifier IC, while the AD526CD also belongs to the programmable-gain-amplifier and analog signal-conditioning categories. Its integrated resistor network simplifies gain selection and reduces the number of external components needed in measurement front ends. TTL-compatible latched inputs allow the selected gain to be held while the circuit is used in a larger control system. The AD526 family provides five standard gain selections: 1, 2, 4, 8, and 16. These binary-selectable ratios are useful when an instrument must accommodate several input ranges with one analog front end. The monolithic implementation places the amplifier and gain network on one integrated circuit, while the latched digital interface supports controlled gain changes from a host controller, measurement system, or instrument bus. The AD526CD is identified specifically as a 16-CDIP package, making it suitable for applications that use ceramic DIP rather than surface-mount assembly. The AD526CD is designed as a complete analog gain-conditioning element. Its single-ended architecture accepts a single input signal and produces a conditioned output with the selected gain. Because the gain-setting network is integrated, designers do not need to calculate, match, or install external feedback resistors for the supported gain choices. The TTL-compatible latched inputs provide a straightforward digital control interface, but input levels, timing, and grounding still require careful treatment in a practical circuit. Typical uses include industrial process measurement, laboratory instrumentation, sensor signal conditioning, data acquisition, and test equipment. In a process-control input module, the AD526CD could normalize signals arriving from sensors with different operating ranges before conversion by an ADC. In laboratory equipment, the five available gains help the same amplifier front end handle multiple measurement scales without manually changing analog hardware. The ceramic DIP package also supports prototyping, educational instruments, and legacy control systems that use through-hole assembly. For implementation, place the device close to the signal source and maintain a low-impedance reference and ground arrangement. Digital gain-control traces should be managed so switching activity does not couple into the high-impedance analog input path. Confirm the power-supply requirements, input and output voltage limits, settling behavior, and acquisition timing from the manufacturer datasheet before finalizing the surrounding circuit. This page also organizes the device’s gains, package, control interface, application role, and sourcing information for faster engineering review.

RFQ پەیوەندی
AD526CDZ - Programmable Gain Amplifier | Analog Devices
AD526CDZ

AD526CDZ - Programmable Gain Amplifier | Analog Devices

The Analog Devices AD526CDZ is a single-ended, monolithic software-programmable gain amplifier (SPGA) with digitally selected gains of 1, 2, 4, 8, and 16, a 4 MHz bandwidth, and a 16-CDIP package. The device operates from dual ±4.5 V to ±16.5 V supplies and is specified over a -40°C to +85°C temperature range. Its integrated amplifier and resistor network eliminate the external gain-setting components normally required by a conventional PGA. A software-programmable gain amplifier is a mixed-signal amplifier that uses digital control signals to select a predetermined gain. In the signal-chain hierarchy, the AD526 belongs to programmable-gain amplifiers, a specialized category of amplifier ICs used for instrumentation, industrial measurement, and data-acquisition systems. By changing gain through latched digital inputs rather than switching external resistors, it simplifies control and reduces the number of discrete components required around the amplifier. The AD526CDZ provides five binary gain settings and uses TTL-compatible latched control inputs. Maximum gain error is 0.02% for the C grade at a gain of 1 and 0.5% at a gain of 16. Its 24 V/µs slew rate supports accurate reproduction of changing input waveforms. Two-chip cascade operation extends the binary gain range to 256, allowing a higher overall gain while retaining the digital gain-control architecture. The AD526 integrates the amplifier and resistor network into one monolithic implementation. Because the gain network is internal, the circuit does not require external gain-setting resistors. The manufacturer identifies the C-grade part as offering a maximum gain error of 0.02% at a gain of 1, while the maximum error rises to 0.5% at a gain of 16. This increasing error with gain is important when interpreting the overall accuracy of a high-gain measurement chain. Typical uses include programmable sensor-signal conditioning, laboratory instrumentation, industrial process measurement, and analog data-acquisition systems. The AD526 is particularly useful when a controller must adjust signal amplitude for inputs spanning several orders of magnitude. Its binary 1-to-16 gain range can be combined with an external attenuator or front-end stage when wider control is required. Layout should preserve short analog input paths, a low-impedance reference or driver path, and clean digital control traces. Mount the device close to the source of the input signal to minimize parasitic capacitance and susceptibility to noise. Confirm the digital-control state before sampling the analog output, because the latched gain setting changes the transfer function and may create a transient during programming. This page consolidates the AD526 family specifications, exact-package alternatives, programming considerations, and application guidance into an engineering-focused resource. It also distinguishes pin-compatible variants from functional or cross-package options, helping engineers evaluate replacements before changing a 16-CDIP circuit board.

RFQ پەیوەندی
AD526JNZ - Software PGA, 1-16x Gain | Analog Devices
AD526JNZ

AD526JNZ - Software PGA, 1-16x Gain | Analog Devices

The Analog Devices AD526JNZ is a single-ended, monolithic software programmable gain amplifier with selectable gains of 1, 2, 4, 8, and 16, a bandwidth of 4 MHz, and a 16-pin PDIP package. It integrates a BiFET amplifier, a laser-trimmed resistor network, JFET analog switches, and TTL-compatible latched gain-control inputs. A software programmable gain amplifier, or SPGA, is an amplifier whose gain can be selected through digital control signals. It sits between the instrumentation-amplifier and operational-amplifier categories, allowing a system to attenuate or amplify a small analog input without changing external resistors. The AD526JNZ supports automatic range control, signal conditioning, measurement systems, and instrumentation where several input levels must share one analog processing chain. The AD526JNZ provides five binary gain selections covering a 1-to-16 multiplication range. Gain is stored in latches, so the selected setting can remain stable while the analog signal is processed. Its monolithic implementation combines the amplifier and precision resistor network on one IC, while TTL-compatible gain-code inputs simplify interfacing with digital control logic. The 4 MHz bandwidth supports signal paths that require useful bandwidth beyond low-frequency precision measurements. Internally, the AD526 uses a drift-trimmed BiFET amplifier with low input bias current, a laser-trimmed resistor network for gain accuracy, and JFET analog switches to select the active resistance. These elements implement the five gain modes without requiring external matched resistors or discrete switch networks. Because the gain code is latched, the control inputs do not need to remain actively driven after a valid code is stored. Typical uses include programmable sensor-frontend scaling, laboratory measurement equipment, automatic-range data acquisition, industrial process monitoring, and communications equipment that accepts signals over a wide dynamic range. Placing the AD526JNZ ahead of an ADC can reduce the likelihood that a large input saturates the converter while preserving resolution for smaller signals. The principal design consideration is digital-control timing. Firmware must set the latched gain code before the analog signal is sampled, and the circuit should avoid changing gain while a conversion is in progress. Power-supply decoupling, grounding, and signal-routing practices also remain important because the AD526JNZ is designed as a sensitive analog block within an otherwise digital system. This page combines the AD526JNZ product identity, programmable-gain architecture, verified ordering information, replacement considerations, application guidance, and engineering design notes. It is intended to help engineers evaluate signal-conditioning requirements before integrating the amplifier into a PCB.

RFQ پەیوەندی
AD526SD - 1, 2, 4, 8, 16 Gain SPGA | Analog Devices
AD526SD

AD526SD - 1, 2, 4, 8, 16 Gain SPGA | Analog Devices

The Analog Devices AD526SD is a single-ended, monolithic software-programmable gain amplifier providing five selectable gain values of 1, 2, 4, 8, and 16. It combines the amplifier, precision resistor network, and TTL-compatible latched digital inputs in a 16-lead CDIP package, so no external gain-setting resistors are required. The device accepts a single-ended input and provides an analog output suitable for instrumentation, data acquisition, and industrial control systems. A software-programmable gain amplifier, or SPGA, belongs to the operational-amplifier and analog signal-conditioning hierarchy. It combines a closed-loop amplifier with selectable internal feedback ratios selected by digital control logic. This integration makes gain changes repeatable and reduces board area compared with a discrete amplifier and switched-resistor network. The AD526SD is therefore useful when a system must adjust measurement range according to changing sensor or input conditions. The AD526 family offers programmable gains of 1, 2, 4, 8, and 16. Its latched inputs allow the selected gain to remain stable after the control word is applied, which is important for multiplexed measurement systems. TTL-compatible logic levels simplify connection to microprocessor, microcontroller, or programmable-logic control circuitry. Because the amplifier, resistor network, and digital interface are integrated in one package, the design does not require external matched resistors or gain-setting components. The monolithic construction supports compact analog signal conditioning while preserving the normal precision behavior associated with an integrated resistor network. The device is intended for single-ended input signals, so system designers should use suitable input protection and referencing when the source can exceed the amplifier's specified operating limits. Digital control should be changed while maintaining valid power-supply conditions, and the selected latch state should be allowed to settle before the analog output is measured. Typical applications include programmable instrumentation amplifiers, data-acquisition front ends, industrial sensor interfaces, medical instrumentation, and laboratory measurement systems. It is particularly useful when a single analog input must be scaled across several ranges without replacing external resistors. In such systems, the AD526SD can be placed near the source to condition the signal before routing it into an ADC, provided the complete signal chain satisfies the manufacturer's grounding and stability requirements. The principal design consideration is to treat the digital gain interface and analog signal path as one precision circuit. Keep the input and output routing compact, provide a stable reference and supply arrangement, and observe the required bypass recommendations in the manufacturer datasheet. When choosing a replacement, verify the exact gain table, temperature grade, package material, pin assignment, and electrical limits rather than relying only on the AD526 family name. This page organizes the AD526SD's gain-control capabilities, package information, procurement path, alternatives, and application guidance into one engineering reference. It also distinguishes exact same-footprint replacement candidates from broader functional comparisons so engineers can assess board-level compatibility before redesigning an existing instrument.

RFQ پەیوەندی
AD5270BCPZ-100-RL7 - 100kΩ 1024-Tap SPI Digital Rheostat | ADI
AD5270BCPZ-100-RL7

AD5270BCPZ-100-RL7 - 100kΩ 1024-Tap SPI Digital Rheostat | ADI

The Analog Devices AD5270BCPZ-100-RL7 is a single-channel, 1024-position digital rheostat (digitally controlled variable resistor) with 100 kΩ nominal end-to-end resistance, housed in a 10-pin LFCSP-WD (3x3 mm) exposed-pad package. It features SPI serial interface control, ±1% end-to-end resistor tolerance error, 50-TP nonvolatile memory (NVM) for wiper position retention, and operates from a 2.7 V to 5.5 V single supply. What is a digital potentiometer/rheostat? A digital potentiometer (also called a digital rheostat or digipot) is a solid-state, electronically adjustable resistor implemented as a string of series-connected resistive elements with CMOS switches that tap off at programmable nodes. Compared to mechanical trimmers, digipots offer remote, microcontroller-controlled adjustment, no moving parts, higher reliability, and - in nonvolatile variants like the AD5270 - retention of the wiper position across power cycles without a microcontroller continuously writing the setting. Digital potentiometers occupy a position in the signal-chain taxonomy between passive components (resistors) and active analog ICs (variable-gain amplifiers). Key differentiating features of the AD5270BCPZ-100-RL7 include industry-leading 1% end-to-end resistor tolerance error (vs. the 20-30% typical of competing rheostats), 50-times-programmable (50-TP) NVM that allows wiper settings to be permanently written during calibration, and a low-temperature-coefficient architecture that maintains setting accuracy over -40°C to +125°C operation. The 1024-tap resolution provides ~0.1% per-step adjustment granularity, making fine calibration of analog signal chains possible in firmware. The AD5270 is built around a string of precision thin-film resistors with CMOS wiper switches, achieving low wiper resistance and excellent temperature stability. The 50-TP NVM uses fuse-link elements for permanent setting retention, after which subsequent writes are blocked - this prevents accidental overwrites in production. The exposed-pad package provides a low thermal-resistance path that keeps wiper-resistance drift minimal even under sustained write operations. Typical applications include precision programmable-gain instrumentation amplifiers, LCD display contrast/brightness control, laser-driver bias calibration, mechanical potentiometer and trimmer replacement, programmable voltage references, and audio attenuators. The 50-TP NVM is especially valuable in factory-trimmed industrial systems where calibration data must survive power-down. Design consideration: when replacing a mechanical trimmer with the AD5270, account for the limited wiper current (typically a few mA maximum) - the AD5270 cannot source/sink large currents or be used as a true power rheostat; it is intended for signal-level adjustment where it presents a high impedance to the surrounding circuit. This page synthesizes 2026 distributor stock and lead-time, drop-in compatible alternatives, and practical calibration-circuit design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
AD5270BCPZ-20 - 20kΩ 1024-Tap SPI Digital Rheostat | ADI
AD5270BCPZ-20

AD5270BCPZ-20 - 20kΩ 1024-Tap SPI Digital Rheostat | ADI

The Analog Devices AD5270BCPZ-20 is a single-channel, 1024-position digital rheostat with 20 kΩ nominal end-to-end resistance, less than 1% resistor tolerance error, and 50-TP (fifty-time programmable) nonvolatile memory, housed in a 10-lead LFCSP-WD (3 mm × 3 mm) package with an exposed pad. It is interface-compatible via SPI and offers 5 V single-supply operation with a rheostat-mode wiper resistance of approximately 35 Ω to 70 Ω, making it suitable for precision analog adjustment in compact systems. A digital rheostat (also called a digital potentiometer or RDAC) is a solid-state variable resistor whose wiper position is set by a digital command instead of a mechanical knob. Internally it is implemented as a string of resistor segments plus MOS switches that connect the wiper to one of the taps; with 1024 taps, the AD5270 achieves roughly 10-bit resolution and supports fine trimming that would otherwise require a manual trim pot. Unlike mechanical trimmers, the wiper position survives power-down thanks to integrated 50-TP EEPROM, allowing the part to be used in factory-calibrated, set-and-forget designs. Key features include 1024-position resolution, 20 kΩ nominal resistance (with -10 and -100 variants also offered), less than 1% end-to-end resistor tolerance error, 50-TP nonvolatile memory for wiper position retention, a standard SPI serial interface, and single 5 V supply operation. The compact 3 mm × 3 mm LFCSP-10 footprint is drop-in compatible with the AD5271 family member, simplifying PCB reuse across resolutions. The exposed pad provides a low-thermal-resistance path, supporting continuous operation across the -40 °C to +125 °C extended industrial temperature range. The architecture combines a precision thin-film resistor string with CMOS switches and on-chip 50-TP EEPROM. The thin-film process delivers the low temperature coefficient and tight absolute tolerance, while the nonvolatile memory allows the part to remember its wiper position through power cycles without requiring continuous software updates. SPI command words are interpreted on-chip to select one of 1024 wiper positions, with readback capability for verifying the stored setting. Typical applications include programmable gain amplification, precision reference adjustment, laser-diode bias trimming, audio volume control, sensor calibration, and instrumentation scaling. Because the part retains its setting in nonvolatile memory, it is well suited to factory-trimmed designs that must boot up with a calibrated state. When designing with this part, observe the absolute maximum wiper current of ±6 mA, decouple VDD with a 1 μF bypass capacitor close to the pin, and ensure the exposed pad is soldered to a sufficient copper pour for thermal dissipation. The 50-TP memory limit should be considered - designs requiring more than 50 writes over the product lifetime must avoid exceeding this threshold. This page synthesizes distributor pricing, drop-in AD5270/AD5271 family variants, and practical design notes that are not aggregated in the manufacturer datasheet.

RFQ پەیوەندی
AD5272BRMZ-20-RL7 - 20kOhm 1024-Tap I2C Digital Rheostat | ADI
AD5272BRMZ-20-RL7

AD5272BRMZ-20-RL7 - 20kOhm 1024-Tap I2C Digital Rheostat | ADI

The Analog Devices AD5272BRMZ-20-RL7 is a single-channel, 1024-position digital rheostat (nonvolatile digital potentiometer) with 20 kOhm nominal end-to-end resistance, housed in a 10-pin MSOP (RM suffix) package supplied on a 7-inch reel. According to the ADI AD5272/AD5274 datasheet, the device integrates industry-leading variable resistor performance with 50-times-programmable (50-TP) nonvolatile memory (NVM), allowing the wiper position to retain its setting across power cycles. A digital rheostat (sometimes called a digital potentiometer or digipot) is a solid-state replacement for a mechanical potentiometer, providing a programmable two-terminal variable resistor that is controlled through a digital serial bus. It belongs to the broader family of programmable analog ICs sitting between passive components (resistors) and full data-acquisition chains, and is widely used where mechanical trimming is impractical: in calibration, gain setting, sensor linearization, and bias adjustment. Key features include 1024 tap points, 1% end-to-end resistor tolerance error, a 2.7 V to 5.5 V single-supply operating range, an I2C-compatible 2-wire serial interface supporting both standard (100 kHz) and fast (400 kHz) modes, and 50-times programmable nonvolatile memory with read-back. The rheostat mode (terminal W to terminal A or B) supports unipolar signal swing, and the device includes power-on preset to midscale. In terms of architecture, the AD5272 uses a CMOS resistor-array structure with a wiper that is digitally addressed and latched into NVM via the I2C bus. The 50-TP architecture provides a controlled write budget to ensure long-term data retention in EEMEM. Compared with purely volatile digipots, the integrated EEMEM eliminates the need for an external EEPROM and a separate programming step on every power-up. Typical applications include mechanical potentiometer replacement, instrumentation gain adjustment, programmable voltage-to-current conversion, laser-trim replacement, and RF attenuator biasing. The combination of 1% resistor tolerance and 50-TP NVM makes the part especially attractive where calibration is performed once at production and then re-used across multiple power cycles. When designing with the AD5272, observe the absolute-maximum terminal voltages (Vdd + 0.3 V and -0.3 V on W/A/B). For ac-coupled or bipolar signals, bias the rheostat inside the supply headroom. For best noise performance, use the lower-resistance variants or connect an external resistor in parallel only when the design explicitly accounts for the resulting ratiometric error. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes drawn from the AD5272/AD5274 datasheet that are not consolidated on any single distributor page.

RFQ پەیوەندی
AD5272BRMZ-50-RL7 - 50kΩ 1024-Tap I2C Digital Rheostat | ADI
AD5272BRMZ-50-RL7

AD5272BRMZ-50-RL7 - 50kΩ 1024-Tap I2C Digital Rheostat | ADI

The Analog Devices AD5272BRMZ-50-RL7 is a single-channel, 1024-position digital rheostat with 50 kΩ end-to-end resistance, nonvolatile memory (NVM), and an I2C-compatible digital interface, supplied in a 10-lead MSOP package on tape and reel. According to the ADI datasheet, the device guarantees less than 1% end-to-end resistor tolerance error and offers a one-time programmable (50-TP) fuse that permanently freezes the wiper position, emulating a mechanical trimmer sealed with epoxy. A digital potentiometer (also called a digital rheostat or digipot) is a solid-state variable resistor whose wiper position is set through a digital command rather than a mechanical knob. It belongs to the broader category of data converters and digital signal conditioning ICs, sitting alongside ADCs and DACs in the signal-chain hierarchy of integrated circuits. The AD5272 combines a precision resistor array, a wiper switch network, and 50-TP nonvolatile memory in one die, allowing the wiper setting to survive power cycles without an external EEPROM. Key features include 1024 tap points (10-bit resolution), 50 kΩ nominal end-to-end resistance, an I2C serial interface that supports up to 400 kHz Fast Mode, a single supply range of 2.7 V to 5.5 V (or ±2.5 V dual supply), and an extended industrial operating temperature range of -40°C to +125°C. The 50-TP fuse command provides a hardware lock against software tampering once the calibration value is finalized, which is critical in safety-relevant and security-conscious designs. The internal architecture uses a thin-film resistor ladder with CMOS wiper switches, achieving low wiper resistance (typically 35 Ω to 70 Ω) and excellent temperature coefficient performance. The on-chip nonvolatile memory stores both the wiper position and the 50-TP lock bit, and the part is guaranteed for 50 TP write cycles and 50,000 wiper re-write cycles. The MSOP-10 footprint measures 3.0 mm × 3.0 mm, occupying roughly one-third of a SOIC-8 footprint while exposing all digital and analog terminals. Typical applications include precision gain adjustment in instrumentation amplifiers, LCD display contrast and backlight brightness control, laser diode bias calibration, mechanical trimmer replacement in new designs, programmable voltage references, and audio attenuators. The 50-TP lock makes it especially attractive for factory-calibrated end equipment where field re-calibration is undesirable. Designers should size the wiper current within the absolute maximum rating (typically a few mA) and add a small series resistor if the load injects transients into the wiper node. When used as a true rheostat (two-terminal variable resistor), tie the W and A or W and B terminals together; when used as a potentiometer (three-terminal voltage divider), use all three terminals for best linearity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not aggregated on a single manufacturer or distributor page.

RFQ پەیوەندی
AD5291BRUZ-20 - 20kΩ 256-Position SPI Digital Potentiometer | ADI
AD5291BRUZ-20

AD5291BRUZ-20 - 20kΩ 256-Position SPI Digital Potentiometer | ADI

The Analog Devices AD5291BRUZ-20 is a single-channel, 256-position digital potentiometer with 20 kΩ end-to-end resistance, nonvolatile memory (NVM) and an SPI serial interface, housed in a 14-pin TSSOP (RU-14) package. According to the ADI AD5291/AD5292 datasheet, this part combines ±1% R-tolerance accuracy with 20-time-programmable (20-TP) memory, allowing wiper settings to be retained through power cycles without an external EEPROM. Headline parameters include 256 tap positions, 20 kΩ nominal resistance, ±1% resistor tolerance, and an SPI-compatible digital interface operating from a single 2.7 V to 5.5 V analog supply plus a 1.7 V to 5.5 V logic supply. A digital potentiometer (often abbreviated digi-pot or RDAC) is a digitally controlled variable resistor that emulates a mechanical potentiometer through a tapped resistor ladder switched by MOSFET transistors. It belongs to the broader category of digital-to-analog converters (DAC) used for resistance, which in turn sits within data-acquisition and signal-conditioning components. Compared to mechanical trimmers, a digi-pot offers remote adjustment, no mechanical wear, and software-controlled calibration. Key features of the AD5291BRUZ-20 include ±1% end-to-end resistance tolerance, a low 5 ppm/°C nominal temperature coefficient, 256 uniform tap points with 5 V/5.5 V single-supply operation, and a 20-time-programmable nonvolatile memory for storing the wiper position through power-down. The part also integrates a hardware RESET pin and software reset command that reloads the most recently programmed 20-TP memory location, plus a power-on refresh circuit that reinitializes the wiper on supply ramp. The internal architecture is a precision thin-film resistor ladder with CMOS transmission-gate switches, driven by an internal RDAC register. A separate 20-bit (AD5291) or 50-bit (AD5292) EEPROM cell stores the user-programmed wiper position. The SPI interface supports daisy-chaining of multiple devices via a dedicated SDO pin, and the logic supply range of 1.7 V to 5.5 V permits direct connection to 1.8 V, 3.3 V, or 5 V microcontrollers without level shifters. Typical applications include programmable gain amplifiers and transimpedance amplifiers, precision reference voltage trimming in instrumentation, audio volume and tone control, LCD display contrast adjustment, programmable filter cutoff and oscillator tuning, and industrial 4–20 mA loop calibration. The TSSOP-14 footprint is friendly to handheld and portable designs where board area is constrained. When designing with this device, observe the absolute maximum analog supply voltage of 6.5 V and keep the logic supply within 1.7 V to 5.5 V. Bypass VDD and VL with 0.1 µF capacitors placed within 5 mm of the supply pins, and reserve a small footprint for an optional 1 µF bulk cap on VDD if the supply is noisy. This page synthesizes distributor pricing, drop-in alternatives sourced from the AD5291 family and competitor cross-reference, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and qualify the AD5291BRUZ-20 faster.

RFQ پەیوەندی
AD5292BRUZ-100-RL7 - 1024-Tap 100kΩ SPI Digital Potentiometer | Analog Devices
AD5292BRUZ-100-RL7

AD5292BRUZ-100-RL7 - 1024-Tap 100kΩ SPI Digital Potentiometer | Analog Devices

The Analog Devices AD5292BRUZ-100-RL7 is a single-channel, 1024-position digital potentiometer with 100 kΩ end-to-end resistance, nonvolatile memory (20-TP), and an SPI serial interface, housed in a 14-pin TSSOP package rated for -40°C to +105°C operation. The device features ±1% nominal resistor tolerance in R-Perf mode, ±35 ppm/°C resistance temperature coefficient, and 50 ppm typical resistor differential nonlinearity, making it one of the most precise digital pots in its class. A digital potentiometer (or digipot) is a solid-state variable resistor whose wiper position is set by a digital code rather than mechanical action. In the signal chain hierarchy it sits between passive mechanical potentiometers and active digital-to-analog converters (DACs), offering software-controlled resistance adjustment, nonvolatile state retention, and PCB-mountable miniaturization. Digipots are commonly used to replace mechanical trimmers in volume controls, gain stages, and calibration circuits. Key features of the AD5292 include 1% resistor tolerance in R-Perf mode, an SPI-compatible serial interface operating up to 50 MHz, and 20-times programmable nonvolatile memory that retains wiper position through power cycles. The 50 ppm/°C temperature coefficient and 50 ppm resistor differential nonlinearity (DNL) ensure stable, monotonic resistance steps across the operating range, which is critical for instrumentation applications. The AD5292 uses an array of 1024 thin-film resistors with CMOS switches and a wiper decoder. The thin-film process provides low noise, low temperature coefficient, and excellent long-term stability compared to polysilicon alternatives. The internal charge-pump generates the gate voltage required for the analog switches, allowing the device to operate from a single 9 V to 33 V analog supply while the digital interface is referenced to a separate 2.7 V to 5.5 V logic supply, simplifying interface to low-voltage microcontrollers. Typical applications include programmable gain amplifiers, instrumentation gain trimming, LCD contrast control, audio volume attenuation, and programmable voltage references. The wide supply range and high voltage tolerance make it well-suited for industrial 24 V bus systems and precision measurement equipment where mechanical trimmers are not acceptable. When designing with the AD5292, place 0.1 µF bypass capacitors close to the AVDD and DGND pins. The SDO pin contains an open-drain N-channel FET and requires an external pull-up resistor if used. The wiper resistance (typically 60 Ω) should be included in gain-error calculations for high-precision circuits. This page synthesizes AD5292BRUZ-100-RL7 distributor pricing, SPI-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD53/009-9 - 40-Channel 14-Bit Parallel DAC | Analog Devices
AD53/009-9

AD53/009-9 - 40-Channel 14-Bit Parallel DAC | Analog Devices

The Analog Devices AD53/009-9 is a 40-channel, 14-bit, single-supply voltage-output digital-to-analog converter packaged in a TQFP-80 (14 mm × 14 mm) package. It is designed for parallel-interface systems requiring multiple independently controlled analog outputs. The device operates from a 2.7 V to 3.6 V supply according to its distributor listing, with datasheet summaries also describing 2.5 V to 5.5 V operation and a typical current consumption of 115 μA. These electrical characteristics place the part in the family of low-power, multi-channel DACs used for signal generation, calibration, and test-system control. A digital-to-analog converter is a data-acquisition IC that converts digital codes into proportional analog voltages or currents. Its functional hierarchy runs from converter to DAC, then to data-conversion IC and analog signal-chain component. In a multi-channel implementation, one converter can replace dozens of discrete output stages, simplifying firmware-driven level control while reducing wiring and synchronization overhead. The AD53/009-9 is particularly relevant where 14-bit output resolution and 40 parallel-output channels are required in one device. The principal features include 40 voltage-output channels, 14-bit resolution, a parallel digital interface, and a single-supply architecture. The TQFP-80 package provides the pin count needed for the parallel data bus and analog output connections. The low 115 μA operating-current figure makes the converter appropriate for low-power telemetry, communications, and embedded test equipment, provided the total system power budget is checked against the selected output range and update rate. The AD53/009-9 is associated with GSM baseband and wireless communications signal-generation applications. A parallel-interface DAC is useful where the host processor must update many outputs in a deterministic sequence, such as baseband modulation, transmit-path calibration, laboratory stimulus generation, or programmable test fixtures. Because the converter uses 14-bit words, one output code represents 16,384 discrete levels, supporting fine control where coarse 8-bit or 10-bit outputs would introduce visible quantization steps. Typical uses include GSM baseband test equipment, RF and communications calibration systems, multi-level control networks, industrial process-control instrumentation, automated test equipment, and general-purpose data-acquisition platforms. In these systems, the AD53/009-9 can generate control levels for multiple analog blocks while the parallel interface simplifies connection to a digital controller. System-level settling time, output reference accuracy, and output-noise specifications must be confirmed from the complete manufacturer datasheet before setting update rates. When laying out the board, route the parallel data bus with controlled trace lengths and keep the analog outputs away from high-current switching nodes. Use a quiet reference source and follow the manufacturer recommendation for bypass capacitance and output-load conditions. Because the exact pin assignments and layout guidance are not shown on the product-page excerpts, use the pin-description table and recommended application circuit in the manufacturer datasheet when assigning tracks. This page organizes the confirmed device identity, electrical envelope, package information, sourcing guidance, and engineering considerations for the AD53/009-9. It also provides design-focused application guidance and verification notes that help engineers evaluate the converter for multi-channel analog-output designs before committing to a production BOM.

RFQ پەیوەندی
AD5303ARU - Dual 8-Bit Rail-to-Rail DAC | Analog Devices
AD5303ARU

AD5303ARU - Dual 8-Bit Rail-to-Rail DAC | Analog Devices

The Analog Devices AD5303ARU is a dual 8-bit buffered voltage-output digital-to-analog converter operating from a single 2.5 V to 5.5 V supply in a 16-lead TSSOP package. It combines two independent DAC channels, on-chip output amplifiers, and a 3-wire serial interface that supports clock rates up to 30 MHz. The converter consumes 230 uA at a 3 V supply, making it suitable for low-power instrumentation and control systems. A DAC is a data-conversion integrated circuit that translates a digital code into a proportional analog voltage or current. The AD5303 belongs to the voltage-output DAC family, where buffered outputs are driven directly by on-chip amplifiers. Its rail-to-rail output stage allows the analog outputs to approach the available supply rails, while the dual-channel architecture supports two independent analog control or excitation channels in a compact footprint. The principal features include 8-bit resolution on each channel, a versatile 3-wire serial interface compatible with SPI, QSPI, MICROWIRE, and DSP interface standards, and serial clock operation up to 30 MHz. Each converter derives its reference from a dedicated reference pin, allowing the two output voltages to be scaled independently. The single-supply operating range supports both 3.3 V and 5 V systems. Internally, the device uses a resistor-string DAC architecture followed by buffered output amplifiers. This arrangement provides direct voltage output without requiring an external output buffer and simplifies connection to analog front ends. The 16-lead TSSOP package is suitable for compact analog and mixed-signal designs, while the dual channel count improves utilization when a system needs two matched control signals. Typical applications include industrial process control, programmable test and measurement equipment, battery-powered instrumentation, sensor excitation, automated test equipment, and general-purpose analog signal generation. Its 230 uA current consumption at 3 V is especially useful in portable and distributed sensing systems where each subsystem must limit standby power. Designers should treat the reference pins as precision analog nodes, route them away from digital switching currents, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Confirm output settling time, reference voltage limits, and logic-level compatibility against the intended clock rate and analog settling requirements. This page combines manufacturer specifications, drop-in device alternatives, application guidance, and design notes for engineers evaluating the AD5303ARU across low-power analog and mixed-signal systems.

RFQ پەیوەندی
AD5316ARU - Quad 10-Bit DAC, 2.5-5.5V | Analog Devices
AD5316ARU

AD5316ARU - Quad 10-Bit DAC, 2.5-5.5V | Analog Devices

The Analog Devices AD5316ARU is a four-channel, 10-bit, buffered voltage-output digital-to-analog converter operating from a single 2.5 V to 5.5 V supply in a 16-lead TSSOP package. It combines four DAC channels with a 2-wire serial interface capable of operating at clock rates up to 400 kHz. A digital-to-analog converter is an interface IC that converts digital control words into proportional analog voltages. The AD5316 belongs to the DAC hierarchy, where it sits between a digital bus and precision analog test, control, or instrumentation circuitry. Its buffered outputs reduce the need for external output amplifiers when driving moderate loads. The four converters provide 10-bit resolution, and the A-grade device has an integral nonlinearity specification of ±4 LSB. On-chip output amplifiers support rail-to-rail output swing with a slew rate of 0.7 V/µs. The single-supply operating range covers both 3.3 V and 5 V systems, while the typical supply current is 500 µA at 3 V for low-power portable and industrial designs. The AD5316 uses a 2-wire serial interface operating up to 400 kHz and is compatible with SMBus-style communication. Each channel provides an independently programmable output voltage through its corresponding DAC register. The interface allows a microcontroller, embedded processor, or programmable controller to update four analog outputs while minimizing the number of signal connections required on the PCB. Typical applications include process-control setpoints, automated test equipment, sensor excitation and bias control, industrial data acquisition, programmable laboratory supplies, and low-power embedded instrumentation. The quad-channel arrangement is particularly useful when a system requires several independently controlled analog outputs but has limited connector and routing space. PCB design should keep the serial interface and output routing compact while observing the analog-ground and supply-return paths recommended in the manufacturer datasheet. Decoupling capacitance should be placed close to the supply pins, and output loads should be checked against the buffered-output capabilities. The 0.7 V/µs slew rate should also be considered when designing waveforms that require rapid output transitions. This page combines the manufacturer's device characteristics, package and interface details, comparison guidance, and practical application guidance to help engineers evaluate the AD5316ARU without relying only on a basic catalog listing.

RFQ پەیوەندی
AD532JDZ - 4-Quadrant Multiplier/Divider | Analog Devices
AD532JDZ

AD532JDZ - 4-Quadrant Multiplier/Divider | Analog Devices

The Analog Devices AD532JDZ is an internally trimmed, four-quadrant integrated-circuit multiplier/divider housed in a 14-lead ceramic DIP package. It performs one multiplication or division function and supports supply voltages from ±10 V to ±18 V. Its specified slew rate is 45 V/µs, and the commercial-temperature grade is specified for operation from 0°C to +70°C. An analog multiplier/divider is an integrated circuit that performs mathematical operations on continuously varying voltages. Unlike digital calculation performed by a microcontroller, this component operates directly with analog signals. The AD532 family belongs to the broader signal-conditioning hierarchy of analog multipliers, analog dividers, function converters, and precision analog ICs. Its four-quadrant behavior supports multiplication and division across positive and negative signal combinations. The AD532JDZ provides one multiplier/divider, three internal amplifiers, and a 14-CDIP package identified by the TO-116 case style. Internally trimmed construction is intended to reduce the need for external calibration of the multiplier core. These features make the device useful when an analog control path needs proportional calculation, signal scaling, or division without converting the measured quantity into a digital representation. The AD532JDZ is specified for ±10 V to ±18 V supply operation and a 45 V/µs slew rate. Those operating limits define the usable bandwidth and settling behavior of circuits built around the device. As an analog multiplier/divider, its practical accuracy also depends on input levels, resistor ratios, frequency content, supply stability, component tolerances, and circuit layout. The manufacturer datasheet should remain the controlling reference for gain accuracy, input impedance, bandwidth, and noise limits before a production design is released. Typical uses include analog multiplier and divider circuits, squaring and square-root functions, algebraic computations, control-loop modulation, servo systems, laboratory instrumentation, and industrial signal-processing equipment. The ceramic DIP construction can also simplify insertion into older through-hole instrument and control hardware. Because Analog Devices marks the AD532 family as not recommended for new designs, it is best treated as a maintenance or redesign component rather than the default choice for a fresh platform. Designers should verify the 14-lead pin assignment, observe the ±10 V to ±18 V supply limits, and maintain signal levels within the multiplier core's linear operating region. Zero-impedance feedback paths must follow the manufacturer's reference topology because excessive impedance can degrade bandwidth and stability. Input and output compensation networks should be placed close to the device, and unused inputs should be returned to an appropriate defined potential rather than left floating. This product page combines lifecycle guidance, package information, operating limits, application analysis, and qualified same-family alternatives. It is intended to help engineers identify the AD532JDZ for legacy or maintenance work while planning a controlled transition to a currently recommended multiplier/divider for new designs.

RFQ پەیوەندی
AD532JHZ - 4-Quadrant Analog Multiplier | Analog Devices
AD532JHZ

AD532JHZ - 4-Quadrant Analog Multiplier | Analog Devices

The Analog Devices AD532JHZ is an internally trimmed, four-quadrant integrated circuit multiplier designed for analog signal processing and instrumentation. It operates from dual supplies of ±15 V and is offered in a 10-pin TO-100 package. Its monolithic construction, internal trimming, and four-quadrant operation allow accurate product or quotient calculations without the external trim networks required by earlier modular multiplier designs. An integrated circuit analog multiplier is a precision signal-processing component that multiplies two input voltages and produces an output proportional to their product. When used in a feedback arrangement with an analog divider, it can also perform division, squaring, root extraction, modulation, demodulation, and signal generation. The AD532 belongs to the broader analog multiplier and divider hierarchy within analog integrated circuits, where precision linear signal processing complements general-purpose amplifier functions. The AD532JHZ combines four-quadrant operation with internal calibration. Four-quadrant capability means the product output can change polarity as either input crosses zero, a requirement for many modulation and control systems. Internal trimming reduces assembly complexity by eliminating external adjustment networks while preserving the factory-calibrated characteristics of the monolithic device. Its dual ±15 V supply also provides sufficient headroom for bipolar analog signals commonly encountered in laboratory and industrial control equipment. The AD532 is specified at 25 °C with ±15 V supply rails and a minimum load resistance of 2 kΩ. These conditions are important when evaluating signal loading, output range, and accuracy because performance and usable output swing depend on the circuit configuration. The device is intended for precision multiplier and divider circuits, including analog control loops, measurement bridges, instrumentation channels, and modulation systems. Typical uses include analog computation modules, laboratory measurement systems, industrial process-control equipment, and communication-signal processing. In each case, the AD532JHZ can implement multiplication directly and division through a closed-loop arrangement. Designers should account for supply polarity, input and output signal ranges, load impedance, grounding, and frequency-dependent accuracy when planning the surrounding analog network. A primary design consideration is preserving the common reference and feedback-node behavior of the multiplier circuit. Incorrect grounding, inadequate return paths, or loading that violates the minimum 2 kΩ load condition can degrade performance. The 10-pin TO-100 package also requires adequate clearance and suitable thermal management because a through-hole package can be exposed to elevated internal temperature at sustained high dissipation. This page combines manufacturer product information, technical search results, package details, lifecycle status, pricing evidence, and practical selection guidance. It also distinguishes genuine pin-compatible AD532 family alternatives from broader analog multipliers that may offer similar functions but cannot be assumed to share the same footprint or pinout.

RFQ پەیوەندی