Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
MC3486NE4 - Quad Differential Line Receiver | Texas Instruments
Texas Instruments MC3486NE4 is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin through-hole DIP package. Designed for balanced digital-interface systems, it supports ANSI TIA/EIA-422-B and TIA/EIA-423-B environments as well as ITU V.10 and V.11 recommendations. The four receiver channels provide a practical way to recover logic-level signals from differential data lines while supporting connection to shared buses through high-impedance output states. A differential line receiver converts the voltage difference between two conductors into a conventional logic-level output. This receiver belongs to the line-driver and line-receiver hierarchy, within interface ICs and data-communication ICs. Differential signaling improves common-mode-noise rejection and allows data to be transmitted reliably over longer cable runs than a single-ended interface. The MC3486NE4 implements four such channels in one package, reducing component count in multi-channel industrial, communications, and data-processing equipment. The principal features include four independent differential receivers, TTL-compatible outputs, 3-state operation for bus-oriented connection, and compatibility with ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, and ITU V.11 interface standards. Its through-hole 16-pin DIP construction supports conventional PCB assembly and repair. The MC3486NE4 suffix identifies the commercial-temperature, plastic-DIP ordering configuration, although individual electrical limits should be confirmed against the manufacturer datasheet for the operating conditions of the finished design. In a typical interface, a remote transmitter sends balanced data into a twisted pair, and the MC3486NE4 detects the differential voltage to produce a logic output for a UART, microprocessor, programmable logic, or other digital controller. Because each receiver is independent, four unrelated channels can be decoded in parallel. The 3-state output feature also permits a receiver output to be disconnected when multiple devices share a bus, provided the control and pull-up arrangements follow the system design requirements. Typical applications include industrial control links, instrumentation interfaces, peripheral data links, telecommunications equipment, and legacy computer peripherals. The device is especially relevant where a modern controller must connect to an RS-422 or RS-423 interface while minimizing the number of receiver packages. Its four-channel architecture can also simplify multi-axis positioning, test systems, and distributed control networks that carry several low-speed differential signals. Designers should verify input voltage limits, common-mode range, propagation delay, enable timing, output drive capability, and temperature limits against the manufacturer datasheet before finalizing the interface. Decoupling and signal-return paths should be arranged to prevent fast digital edges and cable transients from coupling into adjacent channels. Through-hole construction provides mechanical robustness, but the PCB must preserve the exact pin orientation and provide adequate clearance for the receiver's through-hole leads. This page organizes the manufacturer interface standards, package information, sourcing details, candidate replacements, and practical selection guidance for engineers evaluating the MC3486NE4. Cross-references are presented as design aids and should be checked against the complete pinout, timing characteristics, logic states, and environmental limits before a substitution is approved.
MC3486NG4 - Quad Differential Line Receiver | Texas Instruments
Texas Instruments MC3486NG4 is a monolithic quadruple differential line receiver with four independent receivers, TTL-compatible outputs, and three-state output capability in a 16-pin DIP package. Each channel receives differential RS-422 or RS-423 signals, while the tri-state outputs allow multiple devices to share a bus when an output-enable control is inactive. The device operates from a single 5 V supply and is designed for industrial automation and control systems. A differential line receiver is an interface integrated circuit that converts a pair of complementary voltage signals into a single-ended logic-level output. This class of receiver belongs to the interface IC hierarchy, where physical-layer signal conditioning sits between external wiring and digital control logic. Differential reception improves noise immunity by comparing the voltage difference between two conductors rather than relying on one conductor referenced only to ground. The MC3486 provides four complete receiver channels in one package. Its differential inputs support the electrical characteristics associated with TIA/EIA-422-B and TIA/EIA-423-B interfaces, as well as ITU Recommendations V.10 and V.11. TTL-compatible outputs simplify connection to microcontrollers, programmable logic controllers, counters, and other digital systems. Three-state outputs provide a high-impedance condition that can isolate an inactive channel during shared-bus operation. The monolithic implementation gives each receiver an independent signal path while reducing the number of components required on a multi-channel interface card. Operating from one 5 V supply also simplifies system power distribution. The device is particularly suited to RS-422 and RS-423 point-to-point or multidrop arrangements where four balanced channels must be terminated and converted into logic signals. Typical uses include factory automation controllers, industrial data acquisition systems, remote instrumentation, process-control equipment, and communications interfaces. Because the receiver converts external cable signals into digital logic levels, board-level termination, grounding, and routing remain important for dependable operation in electrically noisy environments. Designers should follow the manufacturer datasheet for enable polarity, receiver input handling, supply requirements, and operating limits. Place input and enable traces away from high-current switching paths, use the recommended receiver network, and maintain a low-impedance ground reference between the interface board and its external equipment. This page combines the manufacturer interface description, package information, practical RS-422 and RS-423 design guidance, compatible-product links, and an engineering-focused comparison of identified same-family receiver options.
MC3486NS - Quad Differential RS-422/423 Receiver | Texas Instruments
The Texas Instruments MC3486NS is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin SOIC package. It operates from a single 5 V supply, is designed around TIA/EIA-422-B and TIA/EIA-423-B signaling, and supports the ITU V.10 and V.11 recommendations. The receiver is intended for industrial-control, data-communication, and instrumentation interfaces where multiple balanced lines must be converted into digital logic levels. A differential line receiver is an interface IC that compares two complementary conductors, rejects common-mode voltage and noise, and converts the resulting logic state into a single-ended digital output. In the signal-processing hierarchy, the MC3486NS belongs to the receiver family within line-driver and receiver interface ICs, which ultimately fall under interface ICs and semiconductors. Its four channels allow one package to replace four discrete differential receiver sections while preserving a standardized balanced-line interface. Key features include four differential receivers, TTL-compatible outputs, selectable 3-state output operation, operation from a single 5 V supply, and compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements. The 3-state outputs allow several devices to share a bus when the system controller can place individual receivers in a high-impedance state. The 16-pin surface-mount package supports compact circuit layouts while preserving conventional through-hole-equivalent pin organization. The MC3486 is designed for optimum operation with the MC3487 quadruple differential line driver, providing a complete four-channel transmit-and-receive solution for balanced communications. Its differential input architecture is valuable where cables may pick up noise or where logic devices share a common ground reference. The receiver translates that differential information into TTL-compatible logic suitable for programmable logic controllers, microprocessors, counters, and other digital control systems. Typical uses include industrial automation equipment, RS-422-compatible control links, data acquisition systems, test and measurement instruments, and embedded control equipment requiring several differential inputs. In a four-wire RS-422 interface, the MC3486NS can receive four balanced signals while a corresponding MC3487 family driver transmits the opposite-direction signals. This arrangement supports full-duplex communication over a cable carrying multiple data and control lines. The principal design consideration is correct enable and termination management. The available verified information identifies 3-state outputs but does not provide the detailed enable truth table or pin-level values, so those items must be confirmed in the manufacturer datasheet before implementation. Differential-pair routing, solid grounding, and appropriate cable termination are also essential because receiver performance depends on the physical signal path as well as the IC. This page combines verified manufacturer and distributor information with package guidance, application-oriented analysis, and a drop-in cross-reference assessment. It also distinguishes confirmed substitutes from parts that are only functionally related, helping engineers avoid selecting a driver or a mechanically incompatible package as a receiver replacement.
MC3486NSR - Quad Differential RS-422/423 Receiver | Texas Instruments (Tape & Reel)
The Texas Instruments MC3486NSR is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin SOIC package. It operates from a single 5 V supply, is designed around TIA/EIA-422-B and TIA/EIA-423-B signaling, and supports the ITU V.10 and V.11 recommendations. The receiver is intended for industrial-control, data-communication, and instrumentation interfaces where multiple balanced lines must be converted into digital logic levels. A differential line receiver is an interface IC that compares two complementary conductors, rejects common-mode voltage and noise, and converts the resulting logic state into a single-ended digital output. In the signal-processing hierarchy, the MC3486NSR belongs to the receiver family within line-driver and receiver interface ICs, which ultimately fall under interface ICs and semiconductors. Its four channels allow one package to replace four discrete differential receiver sections while preserving a standardized balanced-line interface. Key features include four differential receivers, TTL-compatible outputs, selectable 3-state output operation, operation from a single 5 V supply, and compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements. The 3-state outputs allow several devices to share a bus when the system controller can place individual receivers in a high-impedance state. The 16-pin surface-mount package supports compact circuit layouts while preserving conventional through-hole-equivalent pin organization. The MC3486 is designed for optimum operation with the MC3487 quadruple differential line driver, providing a complete four-channel transmit-and-receive solution for balanced communications. Its differential input architecture is valuable where cables may pick up noise or where logic devices share a common ground reference. The receiver translates that differential information into TTL-compatible logic suitable for programmable logic controllers, microprocessors, counters, and other digital control systems. Typical uses include industrial automation equipment, RS-422-compatible control links, data acquisition systems, test and measurement instruments, and embedded control equipment requiring several differential inputs. In a four-wire RS-422 interface, the MC3486NSR can receive four balanced signals while a corresponding MC3487 family driver transmits the opposite-direction signals. This arrangement supports full-duplex communication over a cable carrying multiple data and control lines. The principal design consideration is correct enable and termination management. The available verified information identifies 3-state outputs but does not provide the detailed enable truth table or pin-level values, so those items must be confirmed in the manufacturer datasheet before implementation. Differential-pair routing, solid grounding, and appropriate cable termination are also essential because receiver performance depends on the physical signal path as well as the IC. This page combines verified manufacturer and distributor information with package guidance, application-oriented analysis, and a drop-in cross-reference assessment. It also distinguishes confirmed substitutes from parts that are only functionally related, helping engineers avoid selecting a driver or a mechanically incompatible package as a receiver replacement.
MC3487D - 4-Channel RS-422 Driver | Texas Instruments | 5V
The Texas Instruments MC3487D is a quadruple differential line driver with four independent drivers, a 5 V single supply, and a 16-pin SOIC package. Its differential outputs meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, while the tri-state outputs permit a high-impedance state for bus management. Each channel uses a TTL-compatible buffered input to reduce loading, making the device suitable for RS-422 point-to-point and multidrop communications. A differential line driver is an interface IC that converts a single-ended logic signal into a balanced pair of differential signals. In the hierarchy of electronic components, it belongs to the interface IC family, within communication and transceiver devices. Differential signaling improves noise immunity by rejecting common-mode noise and allows reliable data transmission over longer cable runs than ordinary single-ended digital logic. The MC3487D provides four driver channels rather than a full transceiver, so it does not receive differential data. The output-enable function controls the output state, allowing connected drivers to be disabled when they are not active. This is useful in systems that share a bus or require controlled output states. Power-up and power-down protection are also identified in the manufacturer documentation. Typical uses include industrial RS-422 links, data acquisition systems, test equipment, instrumentation, and multi-channel communication links. The 5 V supply operation simplifies interface design in legacy and industrial systems where the host logic uses a 5 V rail. Because it is a driver-only device, the system designer must provide the receiving circuitry and define cable termination, grounding, and enable-control behavior. The main design considerations are signal integrity, cable length, supply decoupling, and output-state control. Differential pairs should be routed with consistent geometry and appropriate grounding. The output-enable signals should be controlled during reset so that multiple channels do not contend on a shared bus. The device is intended for surface-mount assembly in the 16-pin SOIC package.
MC3487DE4 - Quad RS-422 Line Driver | Texas Instruments
Texas Instruments MC3487DE4 is a quadruple differential line driver with four independent outputs, a single 5 V supply, and a 16-pin SOIC package. Each channel receives a TTL-compatible input and produces a balanced differential signal designed to meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements. The MC3487DE4 is suitable for industrial control, instrumentation, data acquisition, telecom, and test-equipment systems that transmit digital signals reliably over longer cable distances than single-ended logic permits. A differential line driver is an interface IC that converts one logic input into two complementary outputs. This arrangement rejects much of the common-mode noise picked up by a cable, improving signal integrity in industrial environments. The MC3487 belongs to the broader interface-IC hierarchy: line driver → differential line driver → digital interface IC → semiconductor. Its four channels allow one package to drive four separate balanced links while sharing a common supply and ground reference. Key features include four independent differential drivers, TTL-compatible buffered inputs, three-state output capability, fast transition times, and high-impedance inputs. Power-up and power-down protection helps prevent uncontrolled driver activity during supply changes. The buffered inputs reduce input loading, allowing the device to operate reliably with standard TTL and CMOS control logic when voltage-level compatibility is confirmed in the system design. Technically, the MC3487 is a single-supply RS-422-focused transmitter rather than a complete bidirectional transceiver. It does not include receiver channels. Systems requiring two-way communication normally combine this driver with a separate differential receiver, such as a compatible RS-422 receiver IC. The differential outputs should be routed as a matched pair to preserve signal polarity and minimize common-mode conversion along the cable. Typical applications include RS-422 test equipment, industrial automation links, programmable logic controller interfaces, data-acquisition systems, servo or motor-control signaling, point-to-point computer peripherals, and instrumentation. Designers should use twisted-pair wiring, provide a stable 5 V supply, connect the common ground reference, and account for the voltage drop and noise margin of the selected cable length. The principal design consideration is ensuring that every connected receiver recognizes the driver’s differential output levels and that unused outputs are handled according to the manufacturer’s recommendations. PCB placement should minimize the distance between the interface connector and driver outputs, while avoiding noisy switching-current paths near the differential traces. This page combines device specifications, sourcing guidance, drop-in alternatives, and practical interface-design notes for engineers evaluating the MC3487DE4.
MC3487DR - 4-Channel RS-422 Driver | Texas Instruments | 5V (Tape & Reel)
The Texas Instruments MC3487DR is a quadruple differential line driver with four independent drivers, a 5 V single supply, and a 16-pin SOIC package. Its differential outputs meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, while the tri-state outputs permit a high-impedance state for bus management. Each channel uses a TTL-compatible buffered input to reduce loading, making the device suitable for RS-422 point-to-point and multidrop communications. A differential line driver is an interface IC that converts a single-ended logic signal into a balanced pair of differential signals. In the hierarchy of electronic components, it belongs to the interface IC family, within communication and transceiver devices. Differential signaling improves noise immunity by rejecting common-mode noise and allows reliable data transmission over longer cable runs than ordinary single-ended digital logic. The MC3487DR provides four driver channels rather than a full transceiver, so it does not receive differential data. The output-enable function controls the output state, allowing connected drivers to be disabled when they are not active. This is useful in systems that share a bus or require controlled output states. Power-up and power-down protection are also identified in the manufacturer documentation. Typical uses include industrial RS-422 links, data acquisition systems, test equipment, instrumentation, and multi-channel communication links. The 5 V supply operation simplifies interface design in legacy and industrial systems where the host logic uses a 5 V rail. Because it is a driver-only device, the system designer must provide the receiving circuitry and define cable termination, grounding, and enable-control behavior. The main design considerations are signal integrity, cable length, supply decoupling, and output-state control. Differential pairs should be routed with consistent geometry and appropriate grounding. The output-enable signals should be controlled during reset so that multiple channels do not contend on a shared bus. The device is intended for surface-mount assembly in the 16-pin SOIC package.
MC3487J - Quad Differential Driver, 5V, DIP-16 | Texas Instruments
The Texas Instruments MC3487J is a quadruple differential line driver operating from one 5 V supply and packaged in a 16-pin dual-in-line package. It provides four independent differential outputs for ANSI TIA/EIA-422-B and ITU Recommendation V.11 interfaces. Each channel uses a buffered TTL-compatible input to reduce loading, while 3-state outputs support shared-bus control. The MC3487J is a through-hole military-temperature-grade DIP-16 option. A differential line driver is an interface IC that converts a TTL-compatible logic signal into a balanced pair of differential signals. The balanced topology helps reject common-mode noise and supports reliable point-to-point data transmission. In the interface hierarchy, the MC3487J belongs to the line-driver family and implements the transmit side of a differential communications link. Its intended counterpart is the MC3486 quadruple line receiver. The MC3487 contains four independent channels, a single 5 V supply architecture, high-impedance inputs, and 3-state outputs. The official product description identifies these features as supporting reduced input current and minimized loading. Power-up and power-down protection are also listed in the device literature. The verified distributor data identifies the MC3487J as a military-temperature-grade, through-hole, 16-terminal rectangular DIP, but does not provide all timing, output-current, or temperature limits. Each output is intended for a balanced differential connection rather than a single-ended RS-232-style signal. Because outputs can enter a high-impedance state, the device can participate in bus-direction or driver-enable control when the system requires it. Designers must still account for the differential network, termination strategy, unused inputs, and the voltage levels required by the connected receiver. Exact propagation delay, transition time, output impedance, and common-mode limits require the manufacturer datasheet. Typical uses include industrial instrumentation, computer peripherals, point-to-point data links, test equipment, and legacy communications interfaces. In a transmitter design, the MC3487J sits between a TTL/CMOS-compatible control circuit and a balanced cable or board trace. The receiving end can use an MC3486 or another compatible differential receiver. Keep the driver close enough to the connector or transceiver boundary that unbalanced stub lengths remain short and the cable transition is clean. The principal design consideration is verifying the 5 V rail and every connected differential input against the device electrical limits before layout release. Decoupling should follow the manufacturer guidance, and unused inputs must not be left in an undefined state if they can affect system behavior. The MC3487J is appropriate when a legacy, balanced, TTL-driven interface is required and a through-hole DIP-16 assembly is preferred over a surface-mount package. This page consolidates the verified Texas Instruments product description, manufacturer datasheet link, package information, distributor price indication, and application-oriented design guidance. It also separates verified facts from parameters that still require confirmation in the datasheet, helping engineers make an evidence-based sourcing decision.
MC3487N - 4-Channel RS-422 Differential Driver | Texas Instruments
The Texas Instruments MC3487N is a four-channel differential line driver operating from a single 5 V supply in a 16-pin dual-in-line package. It provides one differential driver per channel, TTL-compatible buffered inputs, and three-state outputs for interface bus control. The device is designed to meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, making it suitable for point-to-point and multidrop digital communication links. Its bipolar implementation and high-impedance inputs help reduce loading on source logic. The MC3487 is intended for use with compatible differential receivers such as the MC3486 family, while its four independent channels allow several differential signals to be transmitted on one board. The 16-pin PDIP package supports conventional through-hole PCB assembly and straightforward socket or leaded prototyping. An RS-422 differential line driver is a digital interface component that converts a single-ended logic input into a balanced differential output. Differential signaling uses two conductors carrying complementary signals, allowing common-mode voltage and ground-potential differences to be rejected by the receiver. A multi-driver such as the MC3487 consolidates four such output channels in one device, reducing component count and simplifying control in industrial, communications, instrumentation, and embedded systems. The MC3487N is therefore positioned within the hierarchy of logic ICs, interface ICs, line drivers, and communication transceivers. The principal verified features are four independent differential drivers, a single 5 V operating supply, TTL-compatible input buffering, and three-state outputs. The output-enable function is useful when several drivers share a bus or when a system must place an external line into a high-impedance state. Fast transition times support digital data-transfer applications where edge distortion must be controlled. Power-up and power-down protection helps prevent unintended line activity during supply transitions, an important consideration in multi-node equipment. The manufacturer describes the device as interchangeable with compatible RS-422 driver implementations, but system designers should still verify timing, load, protection, and supply requirements for the exact implementation. The MC3487N is a bipolar interface IC rather than a power semiconductor or a modern low-voltage transceiver. It is intended for legacy and established differential-bus designs where 5 V logic, through-hole assembly, and standard RS-422 electrical behavior are priorities. Because the verified data supplied for this page does not include detailed propagation-delay, output-current, input-current, temperature-range, or package-dimension tables, those values are marked as data needed rather than inferred. This preserves separation between verified manufacturer information and engineering estimates. Typical applications include industrial control interfaces, point-to-point serial links, test equipment, data-acquisition systems, peripheral communication, and legacy computer or industrial buses. In a point-to-point link, the MC3487N transmits four complementary differential pairs to a remote receiver. In a multidrop arrangement, the three-state outputs permit driver tri-stating, although cable length, topology, termination, and fault tolerance still require system-level validation. The 16-pin PDIP package is convenient for through-hole designs and prototypes but occupies more board area than a surface-mount equivalent. When laying out a board, place the device near the line-driver outputs and provide a solid ground reference. Keep differential traces coupled and matched in length where practical, provide receiver termination appropriate to the selected RS-422 topology, and leave protection-network space for surge or ESD requirements. Do not assume that a logical replacement preserves all legacy timing and fail-safe behavior; compare the complete data sheets and validate the assembled interface. This page synthesizes verified source links, interface guidance, and comparison structure for engineers evaluating the MC3487N.
MC3487NG4 - 4-Channel RS-422 Differential Driver | Texas Instruments
Texas Instruments MC3487NG4 is a four-channel differential line driver designed for RS-422 and related point-to-point balanced communication links. The device provides four independent differential outputs, uses TTL-compatible buffered inputs, operates from a single 5 V supply, and is housed in a 16-pin dual-in-line package. Its primary function is to convert logic-level control signals into balanced differential outputs suitable for driving transmission lines. The MC3487 is intended for systems using ANSI TIA/EIA-422-B and ITU Recommendation V.11 interfaces, including industrial control, data acquisition, test equipment, and point-to-point communications. A differential line driver is an interface circuit that transmits two complementary signals over a balanced pair of conductors. This signaling method improves noise immunity and helps maintain signal integrity over longer cable runs compared with single-ended logic. The MC3487NG4 uses four independent drivers, allowing one package to support four channels without adding multiple discrete line-driver packages. Each input is buffered with a TTL-compatible input stage, reducing input current and logic-loading requirements. The MC3487NG4 operates from one 5 V supply and is specified for ANSI TIA/EIA-422-B and ITU Recommendation V.11 applications. The device is available in a 16-pin dual-in-line package, and the MC3487NSR is the related surface-mount option identified in the product family. The standard receiver counterpart is the MC3486 quadruple line receiver, which is recommended by the manufacturer for systems requiring complete differential communication interfaces. Typical uses include industrial instrumentation, programmable test equipment, computer peripheral interfaces, factory automation links, and embedded systems that need reliable balanced-line transmission. Because each channel is independent, unused driver channels can be managed according to the device's recommended input and output practices in the datasheet. Termination, cable length, grounding, and logic timing remain important when deploying the part in a complete interface system. The primary design consideration is ensuring that the transmitter, receiver, cable, and termination arrangement form a compatible RS-422 system. A 5 V supply should be decoupled close to the device, and unused inputs should not be left floating if the design requires deterministic operation. The MC3487NG4 is therefore most appropriate when a design needs four channels of compact balanced differential drive in a standard 16-pin DIP footprint.
MC3487NS - 4-Channel RS-422 Driver | Texas Instruments
Texas Instruments MC3487NS is a quadruple differential line driver with four independent drivers, a single 5 V supply, and a 16-pin small-outline package. It is designed to meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, making it suitable for balanced digital data links. Each driver accepts a TTL-compatible input through a buffered input that reduces loading, while the differential outputs support reliable transmission over longer cables in noisy industrial environments. The MC3487NS provides three-state outputs, fast transition times, high-impedance inputs, and power-up and power-down protection. A differential line driver is a signal-conditioning interface that converts one logic input into two complementary outputs for a balanced transmission line. This differential signaling method improves noise immunity because the receiver detects the voltage difference between the two conductors rather than relying on one conductor relative to ground. In the hierarchy of electronic components, the MC3487NS is a line-driver IC, a differential interface IC, and a member of the broader interface IC and semiconductor categories. The principal electrical benefit is the combination of four differential channels in one package, allowing multi-channel data links to share a compact circuit footprint. The single 5 V supply simplifies power design, while TTL-compatible inputs allow direct connection with common digital logic families. Three-state outputs permit a connected driver to present a high-impedance state when it is not actively driving a bus, which is useful in systems requiring controlled driver enable and disable behavior. The MC3487NS is commonly paired with the MC3486 quadruple differential line receiver. It can also be used in industrial control links, instrumentation interfaces, test equipment, data acquisition systems, and communications equipment where a point-to-point or multidrop balanced line must be driven from TTL logic. The fast output transition times support higher data rates while maintaining the differential signaling characteristics expected by RS-422-class systems. Designers should verify the complete pinout and logic levels in the manufacturer datasheet before layout because the supplied web excerpts do not expose the individual pin names. The 16-pin surface-mount package should be treated as a differential signaling device: route the driver outputs as a matched pair, minimize stub lengths, provide a continuous ground reference, and confirm cable termination requirements for the selected data rate and topology. The MC3487 is a driver, not a receiver, and it is not an RS-485 multidrop controller with transceiver arbitration. This product data combines the verified Texas Instruments product description and datasheet links with distributor availability references, practical application guidance, and an explicit separation between confirmed facts and parameters that require datasheet confirmation. Pricing and detailed electrical values must be checked against current authorized distributor inventory and the latest manufacturer documentation before release to production.
MC3487NSR - 4-Channel RS-422 Driver | Texas Instruments (Tape & Reel)
Texas Instruments MC3487NSR is a quadruple differential line driver with four independent drivers, a single 5 V supply, and a 16-pin small-outline package. It is designed to meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, making it suitable for balanced digital data links. Each driver accepts a TTL-compatible input through a buffered input that reduces loading, while the differential outputs support reliable transmission over longer cables in noisy industrial environments. The MC3487NSR provides three-state outputs, fast transition times, high-impedance inputs, and power-up and power-down protection. A differential line driver is a signal-conditioning interface that converts one logic input into two complementary outputs for a balanced transmission line. This differential signaling method improves noise immunity because the receiver detects the voltage difference between the two conductors rather than relying on one conductor relative to ground. In the hierarchy of electronic components, the MC3487NSR is a line-driver IC, a differential interface IC, and a member of the broader interface IC and semiconductor categories. The principal electrical benefit is the combination of four differential channels in one package, allowing multi-channel data links to share a compact circuit footprint. The single 5 V supply simplifies power design, while TTL-compatible inputs allow direct connection with common digital logic families. Three-state outputs permit a connected driver to present a high-impedance state when it is not actively driving a bus, which is useful in systems requiring controlled driver enable and disable behavior. The MC3487NSR is commonly paired with the MC3486 quadruple differential line receiver. It can also be used in industrial control links, instrumentation interfaces, test equipment, data acquisition systems, and communications equipment where a point-to-point or multidrop balanced line must be driven from TTL logic. The fast output transition times support higher data rates while maintaining the differential signaling characteristics expected by RS-422-class systems. Designers should verify the complete pinout and logic levels in the manufacturer datasheet before layout because the supplied web excerpts do not expose the individual pin names. The 16-pin surface-mount package should be treated as a differential signaling device: route the driver outputs as a matched pair, minimize stub lengths, provide a continuous ground reference, and confirm cable termination requirements for the selected data rate and topology. The MC3487 is a driver, not a receiver, and it is not an RS-485 multidrop controller with transceiver arbitration. This product data combines the verified Texas Instruments product description and datasheet links with distributor availability references, practical application guidance, and an explicit separation between confirmed facts and parameters that require datasheet confirmation. Pricing and detailed electrical values must be checked against current authorized distributor inventory and the latest manufacturer documentation before release to production.
MC3488AD - Dual EIA-423/EIA-232D Line Driver | onsemi
onsemi MC3488AD is a dual single-ended line driver designed for EIA-423 and EIA-232D signals, with compatibility also identified for CCITT X.26, X.28, and Federal Standard FIDS1030. The device is intended for applications requiring signal wave shaping when the output load resistance exceeds 450 ohms. It is supplied in an 8-pin SOIC package. Its adjustable output slew rate spans from 1.0 V/µs to 100 V/µs, allowing the transition rate to be adapted to the connected line and receiver. A line driver is an interface circuit that converts digital logic signals into transmission-line-compatible signals for communication links. The MC3488AD belongs to the RS-232 and RS-422 interface IC category, where it provides single-ended output stages for driving external cables or receiver circuits. Compared with a general-purpose logic buffer, its purpose-built driver architecture controls edge transitions and supports the voltage, loading, and waveform requirements associated with established EIA and CCITT communication specifications. The MC3488AD provides two driver channels in one 8-pin SOIC package, reducing the component count in designs requiring more than one transmission-channel output. Its principal documented features include adjustable slew rates from 1.0 V/µs to 100 V/µs, operation with output load resistance greater than 450 ohms, and support for EIA-423, EIA-232D, CCITT X.26, X.28, and Federal Standard FIDS1030. These characteristics make the part relevant to legacy data communications, industrial control links, and equipment interfaces that still use specified single-ended line-driver networks. Slew-rate control is the main technical design variable. A slower edge reduces high-frequency content and ringing but increases transition time, while a faster edge supports higher data throughput at the cost of greater electromagnetic-interference potential and sensitivity to load or termination details. Because the MC3488AD permits adjustable output slew rates, the correct configuration should be selected against the cable length, data rate, receiver thresholds, grounding arrangement, and system EMC requirements rather than chosen solely from a standard data-rate label. Typical uses include industrial serial interfaces, legacy controller peripherals, data-acquisition equipment, and communications systems that require two single-ended line-driver outputs. A board design may pair the MC3488AD with a compatible line receiver such as MC3487DR, a multi-driver interface such as MC3486DR, or a logic interface such as P82B96DR. The output network must be checked against the applicable interface standard because the presence of a compatible logic-side pinout alone does not establish complete system-level interchangeability. When laying out the circuit, keep the output drivers close to their connector or interface-network entry points, provide a stable return path, and verify the selected slew rate against the actual load. Do not infer the complete electrical performance from the EIA references alone; supply voltage, output levels, propagation delay, input compatibility, and absolute maximum ratings must be confirmed in the manufacturer datasheet before production release. This page consolidates the verified manufacturer-document information, exact source links, interface standards, package data, sourcing context, and drop-in comparison candidates for the MC3488AD. It also separates documented facts from values that still require schematic-level verification, helping engineers evaluate this legacy line-driver IC without relying on incomplete distributor summaries.
MC3488ADG - Dual RS-232/RS-423 Driver | onsemi
onsemi MC3488ADG is a dual RS-232 and RS-423 line-driver interface IC with two drivers and no integrated receivers, supplied in an 8-pin SOIC surface-mount package. The device operates from a 10.8 V to 13.2 V supply and is specified for a 0 °C to 70 °C ambient-temperature range. Its two independent driver channels are intended for balanced and unbalanced digital data-interface systems. A line driver is an interface IC that converts logic-level signals into voltage levels suitable for transmission over a wired communications link. Within the hierarchy of interface ICs, a driver sits below multi-channel transceiver and data-converter families and above discrete output-driver circuits. The MC3488ADG supports EIA/TIA-232 and EIA/TIA-423 signaling, allowing legacy serial equipment, industrial control links, and point-to-point data transmission to share a common interface device. Key features include two driver outputs, a 10.8 V to 13.2 V supply range, and an 8-pin SOIC package for compact surface-mount layouts. The absence of integrated receivers means the device does not provide receive-side signal conditioning, termination, or slew control. Its specified 0 °C to 70 °C operating range makes it most appropriate for commercial-temperature equipment rather than extended industrial or automotive environments. The MC3488ADG provides separate transmit channels for interfaces requiring independent driver outputs. In an RS-423 point-to-point arrangement, each driver can feed a balanced or appropriately terminated transmission line. In an RS-232 arrangement, the same pair of driver outputs can support unbalanced links when the surrounding system complies with the applicable EIA/TIA-232 interface requirements. The 8-pin SOIC footprint simplifies board assembly but requires care with trace routing, grounding, and protection against cable-borne transients. Typical uses include legacy serial-port adapters, industrial data acquisition, isolated or protected remote I/O, test equipment, and embedded systems that need a dual RS-232 or RS-423 transmitter stage. The device is particularly suitable where two communication channels are needed without onboard receive channels and where a higher-voltage interface is preferred over a 3.3 V or 5 V logic-level driver. Designers should verify the source and destination logic thresholds, cable length, grounding method, termination, and connector-level protection before assigning the outputs. Because the MC3488ADG is listed as obsolete, new production designs should first confirm lifecycle status and obtain an approved sourcing plan or select a current equivalent after a complete pin and electrical review. This product overview consolidates the package, interface, lifecycle, and replacement information engineers need for initial design triage. It also distinguishes verified device facts from application-specific checks that must be completed against the original datasheet and the target transmission standard.
MC3488ADR2 - Dual RS-232/RS-423 Driver | onsemi
onsemi MC3488ADR2 is a dual RS-232 and RS-423 line driver integrated circuit packaged in an 8-SOIC surface-mount package. The device contains two line-driver channels, supports the EIA-232 and EIA-423 interface families, and is specified as a commercial-temperature component. Its rectangular gull-wing package is identified as the 8-SOIC outline measuring 0.154 inch, or 3.90 mm, in width. A line driver is an interface IC that converts low-level logic signals into differential or balanced transmission-line signals suitable for driving cable-based communications links. In the broader power-management and signal-chain hierarchy, this device belongs to the interface-IC family rather than a voltage regulator or memory component. It is commonly positioned between a UART, transceiver, or other digital controller and a physical data cable, where it provides the electrical drive required at the transmitter end. The principal feature of the MC3488ADR2 is its dual-channel configuration, allowing two communications or control links to be supported by one device. The RS-232 and RS-423 labeling means the same packaged driver can be considered for point-to-point RS-232 links and balanced RS-423-style interconnects, subject to the detailed interface requirements of the connected system. Using a single 8-pin IC for two channels can reduce component count and simplify PCB layout compared with separate single-channel drivers. The MC3488ADR2 is intended for point-to-point, multipoint, or longer-distance interface links where logic-level signals must be transmitted over cables. Suitable equipment includes industrial data acquisition, instrumentation, test and measurement systems, embedded controllers, peripheral interfaces, and legacy computer communications equipment. Because it is a driver rather than a complete transceiver, it does not by itself provide a receive path; the receiving end requires a suitable line receiver or transceiver. When laying out an MC3488ADR2 circuit, place the device near the connector or cable interface, route each driver output directly to its corresponding connector pin, and maintain a common ground reference for the link where required by the selected EIA interface. Avoid long unprotected PCB traces between the IC and connector, and use the application circuit in the onsemi datasheet to select any external wave-shape-control components. Confirm signal levels, operating temperature, supply voltage, and termination requirements against the complete electrical-characteristics table before releasing production artwork. This page combines the verified package and interface identification, practical RS-232 and RS-423 use cases, drop-in replacement assessment, and PCB-focused design guidance for engineers evaluating the MC3488ADR2 in new or existing interface designs.
MC3488AP1 Dual EIA-423/EIA-232D Line Driver | onsemi
The onsemi MC3488AP1 is a dual single-ended line driver designed for EIA-423, EIA-232D, CCITT X.26, X.28, and Federal Standard FIDS1030 signal-interface requirements. The device is packaged in an 8-lead PDIP and provides two driver channels for converting logic-level signals into balanced or unbalanced communication-line waveforms. Its architecture is intended for point-to-point data transmission systems where controlled slew rate, signal shaping, and standard-compliant line levels are important. The MC3488AP1 belongs to the interface IC hierarchy, which includes line drivers, line receivers, RS-232 transceivers, RS-422/RS-485 interface devices, and broader communication ICs. A line driver strengthens a digital signal before it travels through a cable, allowing the signal to retain useful amplitude and timing characteristics over the interconnect. The MC3488A is particularly relevant when an interface must satisfy legacy EIA-423 or EIA-232D signaling requirements rather than only modern logic-level communication. The dual-channel arrangement allows one package to drive two independent communications lines, reducing component count and simplifying board layout compared with separate single-channel drivers. The DIP-8 package supports through-hole assembly and is useful in legacy industrial, telecommunications, instrumentation, and data-communication equipment where component availability, serviceability, and socketed assembly remain important. The manufacturer's MC3488A documentation identifies the device as a dual line driver with externally controlled wave-shaping and slew-rate behavior. Typical applications include legacy data terminals, industrial control links, serial-interface adapters, telecommunications equipment, and embedded systems that need an RS-232D or EIA-423-compatible output stage. The driver should be used with the correct termination, biasing, protection, and cable-routing practices for the selected communication standard. The MC3488AP1 does not include a receiver in the same package, so a separate receiver or transceiver may be required for bidirectional links. When designing a replacement board, verify the exact pinout, supply voltage, output levels, propagation delay, slew rate, and enable or shutdown behavior against the manufacturer datasheet. A nominally similar line-driver package is not automatically a drop-in replacement because EIA-423 and EIA-232D implementations can differ in reference-ground handling, output impedance, and timing. This page combines the manufacturer-aligned part identity, source links, and engineering guidance to support component selection and board-level validation.
MC34978EK - 22-Channel Switch Detection Interface | NXP
The NXP Semiconductors MC34978EK is a multiple switch detection interface that monitors up to 22 switch contacts and transfers their open or closed status to a microcontroller through an SPI interface. It supports 14 switch-to-ground inputs and 8 programmable switch inputs, operates from 4.5 V to 36 V, and is packaged in a 32-pin SOIC wide-body with exposed pad (SOICW-EP 32). A multiple switch detection interface is an interface IC that consolidates multiple discrete switch inputs into a serial communication channel. The MC34978EK belongs to the broader switch detection interface, serial interface, and industrial interface IC categories. Its purpose is to reduce the number of GPIO pins and wiring connections required by a microcontroller while providing diagnostic information for contacts operating in industrial environments. The device provides full functional operation from 4.5 V to 36 V and full parametric operation from 6.0 V to 28 V. Low-power operation is supported by an input battery current of 30 μA in a specified low-power condition and an IDDQ value of 10 μA. The configurable input architecture includes individually selectable input currents in Normal and Low-Power Mode, allowing the system to balance leakage sensitivity, power consumption, and contact diagnostics. The SPI interface provides a structured method for transferring switch status to an embedded controller. Internally, the device is identified as a SMARTMOS interface and includes a 24-to-1 analog multiplexer for reading analog inputs. This combination allows one interface device to handle both switch-state monitoring and selected analog-input multiplexing, reducing board complexity where multiple contact and analog sensing points must share a common controller. Typical uses include industrial control panels, automotive body and electrical systems, building automation, vehicle instrument panels, and equipment with numerous user switches or remote contacts. The wide operating range is particularly useful where the interface must tolerate an automotive or industrial battery-derived supply while maintaining accurate contact-status reporting. Designers should verify the complete pin assignment and exposed-pad connection in the manufacturer datasheet before layout. The SPI interface, analog multiplexing, and configurable input currents require deliberate signal routing, adequate grounding, and validation of switch thresholds under the expected source impedance, wiring length, temperature, and low-power operating condition. This product page consolidates the device’s switch capacity, voltage limits, low-power figures, package information, lifecycle status, and application guidance. It also distinguishes the verified function of the MC34978EK from unverified replacement claims and provides practical interface-design considerations for engineers evaluating a 22-channel switch detection solution.
MC34978ES - 22-Switch SPI Interface | NXP | QFN-32
The NXP Semiconductors MC34978ES is a specialized multiple-switch detection interface that monitors up to 22 switch contacts and transfers their open or closed status to a host processor through a serial peripheral interface. It operates from a 3.3 V or 5.0 V supply and is packaged in a 32-pin QFN with exposed pad, designated 32-QFN-EP (5x5), for compact surface-mount designs. A multiple-switch detection interface is an interface IC that converts many physical switch or contact states into a compact digital representation. It belongs to the broader hierarchy of SPI interface IC, serial interface, interface IC, and semiconductor. Such devices reduce the number of host GPIO pins and wiring connections needed in control panels, appliance interfaces, automotive switch assemblies, and industrial equipment. The primary advantage of the MC34978ES is its combination of 22 input channels and SPI communication. This allows a microcontroller to poll switch status efficiently instead of reading each contact individually. The 3.3 V and 5.0 V operating choices support both modern low-voltage embedded systems and designs based on 5 V logic. Its 5x5 mm QFN-EP package also supports compact layouts, although the exposed pad requires careful PCB thermal design. The MC34978 family uses an SPI interface to report switch opening and closing events. Because the SPI bus can carry the state information over a compact connection, the device is particularly useful where numerous panel switches, interlocks, or discrete contacts must be monitored. Host firmware remains responsible for debouncing contact transitions, interpreting the status registers, and reporting meaningful events to the application. Typical uses include appliance control panels, industrial operator consoles, building-control panels, automotive switch interfaces, and compact human-machine-interface assemblies. In each case, the device can concentrate repeated contact monitoring while leaving the host processor available for user-interface logic, communications, safety supervision, or system control. Electrical isolation, pull-up arrangements, and grounding should be evaluated in the final switch matrix. The primary design consideration is the exposed-pad footprint and the exact input configuration. Place the device according to the manufacturer land-pattern and exposed-pad guidance, connect all required supply and ground pins, and observe the specified operating-voltage range. Review the pin-description table in the manufacturer datasheet when assigning the switch inputs and SPI connections; incorrect signal mapping can disable a channel or interfere with the serial interface. This product record combines the documented 22-switch, 3.3 V, 5.0 V, SPI, and 32-QFN-EP characteristics with application guidance, comparison parameters, and replacement analysis. It is intended to help engineers evaluate the MC34978ES before integrating it into an embedded control system.
MC44BS373CAD - PLL-Tuned UHF/VHF Audio/Video Modulator | NXP
The NXP MC44BS373CAD is a PLL-tuned UHF and VHF audio/video high-integration CMOS modulator designed for VCRs, set-top boxes, and similar consumer video appliances. It supports multiple television standards including NTSC and PAL, integrates a programmable RF output stage, and is controlled via a 5 V- and 3.3 V-compatible I2C bus. The device is supplied in a 16-pin SOIC (SO16NB) small-outline package with gull-wing leads. A modulator (in this context, an RF modulator) is a transmitter IC that mixes a baseband audio and composite-video signal up to a UHF or VHF carrier suitable for direct injection into the antenna input of an analog television receiver. RF modulators sit between the source device (VCR, set-top box, DVD player) and the TV, and historically they were implemented as discrete mixer/oscillator chains. The MC44BS373CA family replaced that discrete chain with a fully integrated PLL-synthesized modulator, dropping dozens of components into a single 16-pin SOIC. Within the broader taxonomy, this part is an RF IC -> modulator -> consumer video IC -> semiconductor. Key specifications include a typical TV output level of 82 dBuV at the antenna terminal, I2C control at standard-mode 100 kHz or fast-mode 400 kHz, multi-standard support (B/G, D/K, M/N, L), and a single 5 V supply. The PLL is fully programmable via the serial interface, removing the manual channel-adjustment trimmers that legacy designs required. A bypass mode supports test and modulation-disabled conditions for factory alignment. Architecturally, the MC44BS373CA uses an on-chip PLL frequency synthesizer driven by an external reference resonator, a programmable divider, and a double-balanced mixer that combines the modulated audio subcarrier with the composite video baseband. The result is a low-phase-noise carrier that meets ETSI EN 50083-13 and FCC Part 15 emission masks for consumer TV modulator products. Compared with the legacy MC44BS373/4 family, the MC44BS373CA revision lowers power consumption and provides finer carrier frequency step resolution. Typical applications include VCR RF output stages, satellite and terrestrial set-top box modulators, DVD player composite-to-RF conversion, game consoles, and CCTV/security observation systems that need to feed analog TV monitors. The wide standard coverage allows a single BOM to ship into multiple regional markets, simplifying manufacturing. Designers should note that the part requires a 75 ohm output network and proper shielding to meet conducted and radiated emissions limits. The external reference resonator value determines the carrier frequency step, and any drift in this component directly translates into channel offset on the TV. This page synthesizes distributor pricing, drop-in alternatives, application circuits, and practical design notes not found in the standalone datasheet.
MC44BS374T1AEF - PLL-Tuned UHF/VHF A/V Modulator | NXP
The NXP MC44BS374T1AEF is a PLL-tuned UHF and VHF audio/video high-integration CMOS RF modulator housed in a 16-pin SOIC (Small Outline IC) package. It is a member of the MC44BS373/4 family of legacy modulators and targets NTSC and PAL television output applications such as set-top boxes, DVD players, VCRs, and video surveillance encoders. The modulator integrates a phase-locked loop (PLL) frequency synthesizer, video modulator, audio FM modulator, and I2C-compatible control interface in a single CMOS die. An RF modulator is a transmitter IC that converts a baseband audio and video signal into a vestigial-sideband or double-sideband RF carrier suitable for connection to a television's antenna input. Within the broader product hierarchy, the MC44BS374 sits at: modulator -> RF transmitter -> specialized consumer IC -> integrated circuit -> semiconductor. It is the direct descendant of the legacy MC44BS373/4 family and is functionally superseded by the newer MC44CC373/MC44CC374 CMOS family while retaining the same footprint and electrical interface to ease migration. Key features include programmable UHF/VHF output frequency via the high-speed I2C-compatible bus, a Logic Output Port pin (pin 3) for status or switching functions, 5 V and 3.3 V compatible I2C logic levels, and a TV output level of 82 dBuV (typical, MC44BS374T1A variant) or 75 dBuV (MC44BS374T1 variant). The PLL architecture provides fine channel selection across the broadcast TV band, allowing the modulator to replace traditional saw filters and discrete modulator circuits in cost-sensitive consumer designs. The IC uses a CMOS process with an integrated VCO and PLL loop filter, reducing external component count compared with older bipolar modulator designs. Typical DC supply is 5 V, and the high-speed I2C bus allows full register configuration of audio deviation, video modulation depth, RF output frequency, and power-down mode. The 16-SOIC package is industry-standard and footprint-compatible with the newer MC44CC374 family, simplifying in-place upgrades. Typical applications include set-top box RF outputs, DVD/VCR combo outputs to legacy televisions, video game console A/V-to-RF adapters, security camera RF modulators, and PC TV-capture cards. The Logic Output Port pin can be used to drive an external LED indicator or switch a relay on channel change. The combination of low external parts count and I2C programmability makes this part attractive for high-volume consumer products. When designing with this modulator, pay close attention to the RF output network - use a proper 75 ohm matching network and shielding to meet FCC/CE radiated emissions limits. Decouple VCC with a 10 uF bulk and 100 nF ceramic capacitor placed as close to the IC as possible; inadequate bypassing produces visible hum bars on the modulated video output. This page synthesizes distributor pricing, drop-in alternatives from the same NXP family (MC44BS373T1AEF, MC44CC373T1AEF, MC44CC374T1AEF), and practical design notes that are not aggregated on DigiKey, Mouser, or Octopart product pages.
MC44BS374T1EFR2 - PLL UHF/VHF A/V Modulator, 16-SOIC | NXP
The NXP MC44BS374T1EFR2 is a PLL-tuned UHF and VHF audio/video high-integration modulator housed in a 16-pin SOIC package, supporting both NTSC and PAL broadcast standards. It delivers synthesized RF output across the UHF/VHF bands from a single 5 V supply and integrates the sound subcarrier oscillator, video modulator, and RF upconverter into a single CMOS die. A video modulator is a specialized IC that mixes a baseband composite video signal (with audio subcarrier) up to a channel-frequency RF output suitable for connection to an antenna input of a TV or set-top box. It belongs to the hierarchy of specialized ICs -> interface ICs -> RF/IF signal chain ICs, and historically served consumer video appliances (VCRs, set-top boxes, DVD recorders, video game consoles) before HDMI replaced analog RF distribution. Key features include a wideband PLL allowing flexible channel selection by I2C programming, low intermodulation distortion for clean video reproduction, separate audio and video inputs, and an integrated DC-DC-friendly architecture that minimizes external component count. The device supports both B/G and D/K system variants in the MC44BS374T1/374T1A family and is footprint-compatible with the earlier MC44BC374T1 generation. From an architectural standpoint, the IC uses a fractional-N PLL synthesizer referenced to a low-phase-noise crystal, allowing fine channel resolution while keeping spurious content low. The modulator chain runs at low power and the RF output stage drives 75 ohm loads with a typical output level in the 70-80 dBuV range, suitable for direct connection to receiver antenna inputs. Typical applications include analog-channel output for legacy TVs in set-top boxes, RF modulation for surveillance camera baseband-to-coax distribution, and modulator modules in VCR/DVD-R designs that must output to older receivers without HDMI inputs. When designing with this device, observe the decoupling requirements from the manufacturer datasheet - typically a 100 nF ceramic on each supply pin plus a bulk 10 uF capacitor at the modulator supply input - and route the RF output trace with controlled 75 ohm impedance for clean spectral output. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers sourcing or evaluating the MC44BS374T1EFR2 make confident second-source decisions.
MC68150FN33 - 5V 68-PLCC Bus Interface IC | Renesas
Renesas Electronics MC68150FN33 is a specialized bus-interface integrated circuit designed for 4.5 V to 5.5 V operation and supplied in a 68-pin plastic leaded chip carrier package measuring 24.21 mm by 24.21 mm. It is listed as an interface IC with J-lead termination and tube packaging, placing it in the broader category of bus interface and data-processing semiconductors. The MC68150FN33 designation identifies a specific operating grade within the MC68150 product family. A bus-interface IC serves as the electrical and protocol interface between a host processor or peripheral bus and a higher-level computer bus. Such devices may translate signals, arbitrate bus ownership, manage timing, or provide the electrical characteristics required by a legacy computer architecture. Because the MC68150FN33 belongs to the specialized MC68150 family, engineers should consult the family documentation for its exact bus protocol, signal timing, and host-interface behavior before finalizing a new design. The principal verified characteristics are a 4.5 V minimum supply voltage, a 5.5 V maximum supply voltage, a 68-pin J-lead PLCC package, a 24.21 mm by 24.21 mm body size, and tube packaging. These parameters make the device suitable for legacy 5 V systems that can accommodate the physical footprint and pin arrangement of the MC68150FN33. The wide 1 V supply range also provides conventional 5 V margin when accounting for supply variation. MC68150FN33 is categorized as a bus interface rather than a general-purpose microcontroller, and its useful operating context is specialized computer and peripheral-interface equipment. Its 5 V supply requirement is consistent with established 68000-family and similar bus-control applications. The J-lead package supports through-hole assembly and may simplify repair or legacy-system maintenance, although the relatively large 68-pin footprint requires careful component placement and adequate connector spacing. Typical engineering uses include industrial control systems, legacy peripheral controllers, embedded computer equipment, and service or modernization projects that retain a compatible MC68150-based bus architecture. In each case, supply sequencing, signal termination, clocking, and device-enable requirements must be checked against the authoritative device documentation. Modern replacements should also be assessed for protocol, timing, voltage, and footprint compatibility rather than function alone. For new PCB layouts, place the MC68150FN33 according to the package drawing and preserve the specified bypass-capacitor and interface routing arrangement. Confirm that the surrounding logic uses compatible voltage levels and that no replacement changes signal polarity, direction, or bus timing. For assembled legacy equipment, inspect all socketed contacts and verify that the tube orientation matches the pin-one marking. This product record combines the confirmed electrical range, package geometry, packaging method, sourcing links, and engineering guidance needed to evaluate the MC68150FN33. It also distinguishes documented facts from parameters that must be confirmed in the authoritative MC68150 datasheet before schematic sign-off, simulation, or production release.
MC68160AEB - Full AUI/TP 10 Mbps Transceiver | Renesas
The Renesas Electronics MC68160AEB is a 1/1 full-duplex enhanced Ethernet interface transceiver supporting IEEE 802.3 AUI and 10BASE-T twisted-pair media connections, with a 10 Mbps data rate in a 52-pin TQFP package measuring 10 x 10 mm. It integrates the functions needed to bridge an Ethernet controller to either an AUI attachment unit interface or a twisted-pair network through external isolation transformers. An Ethernet interface transceiver is an interface IC that converts logical data and control signals between a network controller and physical medium. In the hierarchy, MC68160AEB belongs to the Ethernet interface transceiver and PHY-related class, within interface ICs and broader network-interface semiconductors. Its dual-media support provides a bridge between an AUI-equipped controller and either an AUI connection or 10BASE-T twisted-pair connection. Principal verified features include one full-duplex transceiver, support for both AUI and TP media, IEEE 802.3 operation, and 10 Mbps throughput. The device is described as a BiCMOS interface circuit and uses external isolation transformers for the required media connections. These characteristics make it relevant to legacy 10 Mbps Ethernet systems rather than modern Fast Ethernet or gigabit designs. The MC68160AEB combines media-dependent interface functions with the physical signaling required for 10BASE-T attachment. AUI provides a standardized station attachment interface, while 10BASE-T defines twisted-pair Ethernet signaling. Supporting both interfaces can simplify system design when equipment must interoperate with AUI networks, transition equipment, or older controller platforms using the same external circuitry and logic family. Typical applications include industrial Ethernet controllers, legacy network interface cards, transition equipment, test systems, and embedded equipment requiring IEEE 802.3 AUI or 10BASE-T connectivity. The 52-TQFP package is surface mountable, but designers should preserve the isolation-transformer and network-impedance requirements shown in the manufacturer datasheet. Design consideration: this is a legacy 10 Mbps interface rather than a replacement for modern integrated Ethernet PHYs. Validate controller signal compatibility, isolation components, magnetics, connector layout, and the intended AUI or twisted-pair topology before committing the 52-pin footprint to a new PCB. This page consolidates verified distributor listings, family alternatives, interface characteristics, and practical replacement guidance. It also distinguishes confirmed drop-in-family options from unsupported cross-package substitutes so engineers can assess PCB compatibility before procurement.
MC68160AFB - 1/1 Full Ethernet AUI/TP Transceiver | NXP
The NXP MC68160AFB is a 1/1 full Ethernet interface transceiver built in BiCMOS technology, supporting both IEEE 802.3 AUI and 10BASE-T twisted-pair media connections through external isolation transformers. Its verified package is 52-TQFP, also described as 52-LQFP in a 10 mm by 10 mm form factor, and its specified supply range is 4.75 V to 5.25 V. The device is intended for legacy Ethernet interface designs that require both AUI and twisted-pair connectivity rather than a modern integrated PHY. An Ethernet transceiver is an interface IC that converts digital or differential signals into the physical signaling used on an Ethernet medium. The MC68160AFB belongs to the broader network-interface and communications-IC hierarchy: Ethernet transceiver, network interface, interface IC, and semiconductor. Its AUI support provides attachment-unit-interface media access, while its 10BASE-T support provides 10 Mb/s twisted-pair operation. The verified material identifies the device as supporting both connection types through external isolation transformers, rather than integrating a transformer on the same package. The principal verified features are one transmitter and one receiver, full-Ethernet operation, AUI/TP protocol support, a 4.75 V to 5.25 V supply range, and a 52-pin TQFP/LQFP package. The package is supplied in a tray according to the available component data. The commercial operating-temperature information supplied by one distributor source is 0 degrees C to 70 degrees C. The listed lead-free status says the part contains lead, so it should not be treated as a lead-free or RoHS-compliant modern design choice without additional qualification evidence. The BiCMOS implementation combines bipolar and CMOS circuit techniques, allowing the interface to provide transmit and receive functions in a mixed-signal package. The verified data does not specify the exact internal transceiver architecture, equalization behavior, isolation requirements, propagation delay, output levels, or maximum cable length. Those parameters must be taken from the manufacturer datasheet before final analog and timing validation. The stated AUI and 10BASE-T support is the key technical feature for determining whether this legacy interface IC is appropriate for a given board. Typical applications include legacy 10 Mb/s Ethernet adapters, industrial data-collection equipment, embedded control systems, AUI-to-10BASE-T media bridges, and test systems that retain older Ethernet physical-layer infrastructure. In these systems, the MC68160AFB can be used where the system controller already handles the Ethernet MAC or frame protocol and only requires the physical medium interface. It is particularly relevant to equipment that needs selectable AUI or twisted-pair media connections and can accommodate external isolation transformers. The primary design consideration is system compatibility. The 52-TQFP package, 5 V supply, external isolation-transformer requirement, and legacy Ethernet protocol must all be confirmed before layout. A modern design with integrated 10/100 Ethernet PHY support may be simpler, but replacing this part with a modern PHY is not a pin-compatible substitution and generally requires redesign. For an existing MC68160AFB board, verify the exact pin functions, transformer center-tap requirements, termination network, and signal timing against the manufacturer datasheet before production. This page consolidates the verified manufacturer and distributor descriptions, exact package and supply information, cross-reference results, and engineering-oriented selection notes. It also distinguishes verified facts from fields that remain unavailable, avoiding unsupported claims about pinout, pricing, detailed timing, or universal replacement compatibility.