Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
TC7S66FU - 5-Pin SPST Analog Switch | Toshiba
The Toshiba TC7S66FU is a single-pole single-throw (SPST) bilateral analog switch in a 5-pin SOT-353 (USV) package, fabricated in Toshiba's L-MOS (Low-power MOS) high-speed process. It functions as one SPST FET switch with a 1:1 signal path, making it suitable for signal routing and multiplexing in space-constrained designs. An analog switch (also called a bilateral switch or pass gate) is a semiconductor device that uses MOSFET transistors to route analog or digital signals bidirectionally. Like mechanical relays, analog switches can isolate or connect signal paths, but they offer much faster switching speeds (nanoseconds), lower power consumption, and smaller packages. Analog switches sit within the broader hierarchy: analog switch -> multiplexer/switch IC -> interface IC -> signal chain component -> semiconductor. The bilateral nature means either terminal can act as input or output. Key features of the TC7S66FU include a wide supply voltage range starting from 2V, low on-resistance from the CMOS pass gate, high-speed switching suitable for digital logic level translation, and a low-power design philosophy derived from the L-MOS process family. The CMOS construction provides high off-isolation and minimal charge injection compared to older bipolar bilateral switches. Technically, the device uses a parallel N-channel and P-channel MOSFET configuration to achieve true bilateral signal passing, which is essential when the signal can swing both above and below the reference. This allows the switch to pass audio, video, data, or DC signals without DC offset. The L-MOS high-speed series designation indicates the part is optimized for low quiescent current while maintaining nanosecond-class transition times. Typical applications include portable consumer electronics where board area is critical, audio signal routing in headphone/microphone paths, battery-powered instrumentation, digital logic level shifting between asynchronous domains, and simple multiplexer stages in measurement circuits. The SOT-353 (USV) package is among the smallest 5-pin footprints available, making the TC7S66FU a popular choice for handheld and wearable products. When designing with this part, note that the SPST switch has no dedicated enable or address pin; the ON/OFF state is controlled by a logic-level input that is latched or driven directly by the host controller. Ensure the control logic is referenced to the same supply domain as VCC, and account for switch on-resistance in the signal path when calculating insertion loss for precision analog signals. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives from the same Toshiba L-MOS family, and practical design guidance that complements the manufacturer datasheet.
TCA1116PWR - 16-Bit I2C I/O Expander | Texas Instruments
The Texas Instruments TCA1116PWR is a low-voltage 16-bit I2C and SMBus parallel I/O expander with interrupt and reset functions, operating at up to 400 kHz in a 24-pin TSSOP package. Its 16 configurable ports expand a host controller's digital input and output capacity while preserving a compact serial-bus architecture. The device supports 1.65 V to 5.5 V operation, 5 V-tolerant I/O, and 1.8 V I2C operation. An I/O expander is an interface IC that translates serial I2C commands into parallel digital signals. It sits between a microcontroller or other host controller and external switches, sensors, indicators, or logic inputs. The TCA1116PWR belongs to the I/O expander category, the interface IC category, and the broader semiconductor hierarchy. Its purpose is to reduce the number of GPIO pins required by embedded systems while allowing the added ports to be addressed through the I2C bus. Key features include 16 independently usable I/O ports, 400 kHz serial-bus operation, an active-low open-drain interrupt output, and an active-low reset input. The I/O pins tolerate 5 V signals, while the SDA and SCL inputs remain 5 V tolerant during partial power-down with less than 1 uA of leakage even when VCC is zero. These features allow mixed-voltage interfaces and controlled shutdown behavior in compact embedded systems. The TCA1116PWR is designed for systems in which a host needs more parallel lines than its controller provides. Two programming interfaces can address the expander, and its address inputs support placing multiple devices on one bus. The interrupt output allows the controller to avoid continuous polling when a connected peripheral changes state. Reset provides a defined startup state for the ports and helps simplify firmware initialization across a multi-device system. Typical uses include industrial control modules, building-automation interfaces, sensor aggregators, programmable logic controllers, LED and relay monitoring, test equipment, and embedded human-machine interfaces. In a sensor aggregation circuit, the host can configure input ports, read multiple digital signals, and use the interrupt line to request service only when a monitored event occurs. The TCA1116PWR is particularly useful where board area and host-controller pin count are constrained. When laying out the circuit, connect pull-up resistors to the appropriate I2C supply and keep SDA, SCL, and interrupt traces away from noisy switching nodes. Confirm the device address configuration and reset state in firmware, and account for the open-drain nature of the interrupt output when selecting its pull-up network. This page consolidates the device function, interface limits, package details, practical design guidance, and qualified drop-in comparison information to support faster component selection and PCB implementation.
TCA3385-FP Telephone Ring Signal Converter | Motorola
The Motorola TCA3385-FP is a telephone ring signal converter integrated circuit offered in a 16-pin SOG package. Its primary function is to support telephone-line ringing interfaces, while the verified distributor information identifies it as a telecom IC and the manufacturer datasheet describes it as a telephone ring signal converter. The available catalog data confirms the MPN, package class, current distributor listing, and a starting price of $0.6525 as of 2026-10-29. A telephone ring signal converter belongs to the interface IC category within the broader semiconductor hierarchy. Telephone equipment must distinguish ringing voltage from normal speech and off-hook signals, often while protecting line-facing circuitry from the higher voltage used during the ringing interval. This device is intended for that signal-conditioning role rather than for general-purpose logic, memory, or power conversion. Its exact electrical limits, timing characteristics, and application topology must be confirmed in the manufacturer datasheet. The verified sources identify TCA3385-FP as a Telecom IC in a 16-SOG package. LCSC lists the component as in stock with a starting price of $0.6525, while DigiKey Marketplace identifies a Rochester Electronics listing and Octopart reports pricing from two distributors. These details make the device available for comparison and sourcing, although they do not establish that every distributor offers identical stock, warranty terms, or production quantities. Typical uses include telephone-line ringing interfaces, analog telephone equipment, and legacy telecom systems in which the circuit receives or conditions a ring signal. The implementation should account for the line voltage, ringing cadence, protection requirements, grounding, and isolation boundaries defined by the telephone interface being supported. The complete pin assignments and application schematic are not present in the supplied verification data, so they should not be inferred from generic 16-pin packages. For new designs, engineers should verify the TCA3385-FP against the original schematic and the latest available manufacturer documentation before layout release. In particular, check maximum voltage, quiescent current, interface timing, exposed or non-exposed pad arrangement, and external component requirements. Distributor snippets alone are not sufficient for safety-critical or high-volume production sign-off. This page combines verified distributor availability, package identification, purchasing information, and application-oriented engineering guidance. It clearly separates confirmed facts from parameters that still require datasheet verification, helping engineers evaluate the TCA3385-FP without mistaking catalog metadata for complete electrical specifications.
TCA355GXK - Capacitive Touch Proximity Sensor | Infineon
Infineon Technologies TCA355GXK is a capacitive touch proximity sensor integrated circuit offered in an 8-pin SOIC package. The verified distributor information identifies the device as an Infineon capacitive touch sensor and provides part data, pricing, availability, pinout diagrams, and datasheet links through authorized distribution listings. Its DSO-8 form factor supports compact proximity-detection designs where a conventional discrete sensor and its associated routing would consume excessive board area. A capacitive proximity switch is a semiconductor device that detects the presence of a nearby conductive object through changes in an electric field. In the product hierarchy, the TCA355GXK is an integrated circuit, a capacitive touch sensor, and a proximity-sensing device. Unlike a mechanical switch, it can detect approach without physical contact, supporting touch-oriented controls, presence detection, and compact user interfaces. The verified package information identifies the TCA355GXK as an 8-SOIC, measuring 0.154 inch or 3.90 mm in width. A public, manufacturer-hosted pinout was not included in the supplied data, so no pin names or pin numbers have been inferred. The package_svg_key is therefore based only on the verified eight-pin SOIC package designation, while the detailed pinout remains null pending confirmation against the manufacturer datasheet. Verified commercial information shows TCA355GXK listings from LCSC beginning at $0.7758, an icDirectory listing at $1.94000 with 9,850 units indicated in stock, and an eBee listing beginning at $2.4325. Prices and inventory are distributor-specific and may change without notice. Consequently, all pricing references in this record are stated as of 2026-10-28. The TCA355GXK is appropriate for engineers evaluating compact capacitive proximity sensing in consumer controls, industrial panels, appliance interfaces, and access-oriented products. Design validation should include electrode geometry, environmental moisture, conductive-object properties, operating distance, and response behavior for the target enclosure. Those application-specific tuning values are not supplied in the verified web data and must be established with the manufacturer datasheet and prototype measurements. This product record combines verified package and distributor information with explicit uncertainty markers for missing electrical characteristics. It also distinguishes the confirmed eight-pin package from unverified pin assignments and avoids treating generic cross-reference search pages as evidence of electrically equivalent drop-in replacements. Engineers should compare the complete manufacturer specification set before committing a PCB footprint or production quantity.
TCA39306DCURQ1 - Dual I2C/I3C Level Translator 12.5MHz | TI
The Texas Instruments TCA39306DCURQ1 is an automotive-qualified dual bidirectional voltage-level translator compatible with I2C, SMBus, and I3C buses, featuring an enable (EN) input and packaged in an 8-pin VSSOP (DCU) surface-mount package. It supports VREF1 from 0.9V to 3.3V and VREF2 from 1.8V to 5.5V, enabling bidirectional voltage translation between 0.85V and 5V rails without a direction pin, with a maximum data rate of 12.5MHz. A voltage-level translator is an interface IC that allows devices operating at different supply voltages to communicate over the same two-wire or multi-drop bus. In the hierarchy of signal-integrity components, it sits between the I2C buffer/repeater family and general-purpose level shifters, and is classified as a voltage translator within the broader interface IC and communication semiconductor categories. Key features include bidirectional operation without a DIR pin, I3C compatibility with support for open-drain and push-pull signaling, a low ON-state resistance (RON) pass-gate switch architecture that minimizes signal distortion, and an EN input that places both channels in a high-impedance state when disabled. The low RON of the internal switch allows connections to be made with minimal propagation penalty and reduced pull-up loading. Architecturally, the TCA39306 uses a two-reference-rail topology: the pass transistors compare VREF1 and VREF2 so that a low level on either side propagates correctly to the opposite side. This pass-gate approach is faster and lower-power than open-drain FET arrangements, which is what enables 12.5MHz (Fast-mode Plus and I3C-class) operation. Typical applications include automotive body electronics and infotainment I2C bus translation, RTC-to-microcontroller interfaces spanning backup-battery and main-rail domains, industrial sensor modules bridging 3.3V MCUs to 5V peripherals, and I3C sensor hubs. AEC-Q100 qualification makes it suitable for automotive temperature environments. Design tip: select pull-up resistors per the I2C standard-mode (100kHz) and fast-mode (400kHz) maximum/minimum resistance limits shown in the TI datasheet, and tie EN to the lower-voltage domain to guarantee correct default state. This page adds value beyond the datasheet by compiling distributor pricing, drop-in alternatives, comparison tables, and practical design notes in one place.
TCA4311ADR - 2.7-5.5V I2C/SMBus Buffer | Texas Instruments
The Texas Instruments TCA4311ADR is a 2-bit bidirectional hot-swappable I2C/SMBus buffer operating from 2.7 V to 5.5 V, supporting bus frequencies up to 400 kHz in an 8-pin SOIC package. It buffers the SDA and SCL lines, increases bus fanout, and uses 1 V precharge on SDA and SCL to reduce corruption during live connections. The device is specified for temperatures from -40 °C to +85 °C. An I2C buffer, also called a bus buffer or bus repeater, is an interface IC placed between two bus segments. It reproduces the SDA and SCL signals in both directions so that bus capacitance, voltage-level differences, and long interconnect sections can be managed more effectively. In the broader hierarchy, the TCA4311ADR belongs to the I2C interface-controller, bus-buffer, interface-IC, and semiconductor categories. The principal features include bidirectional operation on both SDA and SCL, a 2.7 V to 5.5 V operating-power-supply range, and support for I2C/SMBus signaling at up to 400 kHz. Hot-swappable operation addresses systems in which a peripheral may be connected or disconnected while the bus remains active. The 1 V precharge feature helps limit signal corruption during those live insertion and removal events. The TCA4311ADR contains separate buffered paths for SDA and SCL, allowing two-wire bus segments to be isolated with respect to signal propagation and bus loading. Its 8-pin SOIC package is intended for surface-mount assembly. Because the device operates bidirectionally, the SDA and SCL connections must remain correctly terminated and must not introduce additional pull-up paths that exceed the design limits of the bus. Typical uses include hot-pluggable I2C peripherals, bus-isolation and level-translation interfaces, removable sensor modules, card-edge connections, and systems where one bus segment must connect to another without directly loading the entire bus. The 400 kHz operating limit also makes the device appropriate for standard fast-mode I2C equipment, including sensors, EEPROMs, and low-to-medium-rate control peripherals. Designers should account for the hot-swap path, external pull-up resistors, bus capacitance, and the voltage applied to each side of the buffer. Verify signal rise times at the intended bus frequency and ensure that powered-off or disconnected modules cannot back-power either bus segment. The manufacturer pin-description table should be used when assigning tracks and checking pull-up placement. This page combines the manufacturer product information, exact ordering information, supported operating limits, and cross-reference findings into a design-focused overview. It also identifies the limits of available replacement data so engineers can distinguish confirmed package and family options from candidates that still require independent pin-level and timing validation.
TCA4311D - 2.7-5.5V Hot-Swappable I2C Buffer | TI
The Texas Instruments TCA4311D is a 2-bit bidirectional, hot-swappable I2C/SMBus bus buffer operating from 2.7 V to 5.5 V at up to 400 kHz, and it is packaged in an 8-pin SOIC. It separates a backplane from cards that may be inserted or removed while the bus is operating. According to the Texas Instruments product page, the device connects SDAIN and SCLIN to SDAOUT and SCLOUT when READY is high. An I2C bus buffer is a signal-conditioning interface IC used to isolate two bus segments, extend usable topology, and support controlled card insertion or removal. In the device hierarchy, this function belongs to interface ICs and specifically to bidirectional bus buffers, repeaters, and accelerators. The TCA4311D supports both I2C and SMBus-style two-wire systems, where data and clock lines require buffering rather than unidirectional level translation. Verified headline features include a 2.7 V to 5.5 V operating range, 400 kHz operation, bidirectional signal paths, hot-swappable bus isolation, an enable control, and an open-drain READY output. The READY output indicates that the backplane and card sides are connected together. When EN is high, normal operation resumes; setting EN low places the device into shutdown mode while the I2C bus is idle. The I2C specification cited by Texas Instruments permits up to 400 pF maximum bus capacitance, which can constrain practical bus length. The SMBus specification does not impose that capacitance restriction, although connected-device impedances still limit how quickly the system can meet rise-time and fall-time requirements. Designers should therefore evaluate board capacitance, wiring, pull-ups, and connected-device loading rather than treating buffer insertion as a universal cure for bus-loading problems. Typical uses include server and desktop backplanes, plug-in acquisition modules, industrial control cards, communications equipment, and embedded systems where a card connects to an always-powered bus. The buffer is placed between the backplane pins and card-side pins, preserving independent local behavior on each side. System designers should verify idle-bus shutdown sequencing and interpret READY correctly before enabling the card interface. PCB layout should keep SDA and SCL routing compact, preserve the intended pull-up arrangement on each bus side, and provide the decoupling and grounding required by the manufacturer datasheet. Because the verified material does not expose complete electrical timing, current, capacitance, and pin-level limits in the supplied text, those values remain marked for data completion rather than being inferred. This page combines verified manufacturer and distributor information with design guidance, replacement analysis, and practical procurement context. It also distinguishes true pin-compatible alternatives from packaging-only orderable variants, helping engineers make evidence-based interface decisions.
TCA4311DR - 2.7-5.5V Hot-Swappable I2C Buffer | TI (Tape & Reel)
The Texas Instruments TCA4311DR is a 2-bit bidirectional, hot-swappable I2C/SMBus bus buffer operating from 2.7 V to 5.5 V at up to 400 kHz, and it is packaged in an 8-pin SOIC. It separates a backplane from cards that may be inserted or removed while the bus is operating. According to the Texas Instruments product page, the device connects SDAIN and SCLIN to SDAOUT and SCLOUT when READY is high. An I2C bus buffer is a signal-conditioning interface IC used to isolate two bus segments, extend usable topology, and support controlled card insertion or removal. In the device hierarchy, this function belongs to interface ICs and specifically to bidirectional bus buffers, repeaters, and accelerators. The TCA4311DR supports both I2C and SMBus-style two-wire systems, where data and clock lines require buffering rather than unidirectional level translation. Verified headline features include a 2.7 V to 5.5 V operating range, 400 kHz operation, bidirectional signal paths, hot-swappable bus isolation, an enable control, and an open-drain READY output. The READY output indicates that the backplane and card sides are connected together. When EN is high, normal operation resumes; setting EN low places the device into shutdown mode while the I2C bus is idle. The I2C specification cited by Texas Instruments permits up to 400 pF maximum bus capacitance, which can constrain practical bus length. The SMBus specification does not impose that capacitance restriction, although connected-device impedances still limit how quickly the system can meet rise-time and fall-time requirements. Designers should therefore evaluate board capacitance, wiring, pull-ups, and connected-device loading rather than treating buffer insertion as a universal cure for bus-loading problems. Typical uses include server and desktop backplanes, plug-in acquisition modules, industrial control cards, communications equipment, and embedded systems where a card connects to an always-powered bus. The buffer is placed between the backplane pins and card-side pins, preserving independent local behavior on each side. System designers should verify idle-bus shutdown sequencing and interpret READY correctly before enabling the card interface. PCB layout should keep SDA and SCL routing compact, preserve the intended pull-up arrangement on each bus side, and provide the decoupling and grounding required by the manufacturer datasheet. Because the verified material does not expose complete electrical timing, current, capacitance, and pin-level limits in the supplied text, those values remain marked for data completion rather than being inferred. This page combines verified manufacturer and distributor information with design guidance, replacement analysis, and practical procurement context. It also distinguishes true pin-compatible alternatives from packaging-only orderable variants, helping engineers make evidence-based interface decisions.
TCA4311DRG4 - 400kHz Hot-Swap I2C Buffer | Texas Instruments
The Texas Instruments TCA4311DRG4 is a 2-bit bidirectional I2C and SMBus buffer accelerator with a 2.7 V to 5.5 V supply range, 400 kHz bus speed, hot-swap capability, and an 8-pin SOIC package. It supports two-wire bus buffering and allows systems to isolate bus capacitance while improving signal integrity during live insertion or removal. An I2C bus buffer is a bidirectional interface IC that separates a potentially noisy or capacitively loaded bus section from the rest of a two-wire bus. The TCA4311 belongs to the broader I2C interface IC hierarchy, where bus buffers, accelerators, repeaters, and hot-plug controllers support reliable communication between processors, sensors, memory devices, and expansion cards. Its 2-bit architecture provides two buffered channels in a compact surface-mount package. The principal operating characteristics include a 2.7 V minimum supply, 5.5 V maximum supply, and support for 400 kHz I2C operation. The device is intended for hot-plug or hot-swap systems in which a peripheral may be connected to a live bus. Its bidirectional channels allow controller and peripheral traffic to pass through the buffer without changing the underlying open-drain I2C signaling method. The TI TCA4311 product page identifies the device as a 2-bit bidirectional 2.7 V to 5.5 V hot-swappable 400 kHz I2C or SMBus buffer. The manufacturer datasheet explains that I2C limits total bus capacitance to 400 pF, while SMBus does not impose the same capacitance limit. A buffer can therefore divide a long or heavily loaded bus into shorter segments, reducing the capacitive burden seen by a controller while preserving communication across both segments. Typical uses include industrial control modules, hot-pluggable sensor cards, server peripherals, communications equipment, and embedded systems that add or remove equipment while powered. It can also isolate a short, heavily loaded bus segment from a cleaner segment, improving rise-time behavior and reducing the probability that multiple peripheral pull-up networks combine into an excessive effective load. When laying out a board, route the buffered bus sections as controlled transmission-line segments with continuous ground references, place the device close to the bus boundary, and keep both sides of the buffer free of unnecessary stubs. Confirm voltage compatibility, pull-up placement, logic levels, and bus capacitance before implementation because the buffer does not translate voltage levels or replace pull-up resistors. This product page organizes the electrical characteristics, ordering information, drop-in alternatives, comparison parameters, and application guidance around the TCA4311DRG4. It is intended to accelerate component selection, PCB planning, and replacement analysis while keeping each engineering conclusion tied to the manufacturer documentation or an identified cross-reference result.
TCA5013ZAHR - Smart Card Interface | Texas Instruments
The Texas Instruments TCA5013ZAHR is a smart card interface IC designed for one user card and up to three Secure Access Module (SAM) cards. The device operates from a single supply, generates the required card voltages, and supports ISO 7816-3 and ISO 7816-10 compliant cards for point-of-sale terminals and other secure-access systems. It is packaged in a 48-pin NFBGA (ZAH) package measuring 5 x 5 mm. A smart card interface IC is an interface-controller device that connects a host processor with ISO 7816 smart cards and SAMs. It manages card power, card-clock and card-data signaling, card insertion detection, and the host-side control interface. The TCA5013 is intended for systems requiring one user-card slot plus multiple SAM sockets, allowing payment terminals and access-control products to share a controlled smart-card subsystem. The TCA5013 supports EMV 4.3, ISO 7816-3 and ISO 7816-10 applications. Its single-supply architecture reduces the number of external card-voltage rails required by the host design. The device also includes an I2C control interface and is designed to operate in the industrial temperature range from -40 °C to 85 °C. The 48-terminal NFBGA package provides a compact surface-mount solution for space-constrained terminal hardware. The manufacturer describes the TCA5013 as a feature-rich smartcard interface IC for payment-terminal designs. A typical implementation places the TCA5013 between the host controller and one user-card connector, with additional connectors for as many as three SAM cards. Card insertion and removal can be detected, while the IC controls the card interfaces and generates the card voltages required by the attached cards. The host configures the device through I2C rather than reproducing low-level card timing and power management in application firmware. The TCA5013 is suitable for electronic point-of-sale terminals, payment acceptance equipment, secure-access readers, banking terminals, and other ISO 7816-based systems. The TIDA-00382 reference design provides an implementation pattern for an electronic point-of-sale smart-card subsystem, including a user-card slot and TCA5013-based card detection. It is also useful where multiple secure credentials must be evaluated while maintaining a compact board footprint. PCB implementation requires careful BGA escape routing and power-supply integrity. Place the device close to the user-card and SAM connectors to minimize clock and data trace lengths, route sensitive signals away from switching nodes, and follow the manufacturer’s NFBGA land pattern and assembly guidance. Confirm the card connector pin assignments, pull-up requirements, supply capacitance, and signal-level compatibility before releasing the layout. This product page combines the manufacturer’s smart-card interface specifications with package and ordering details, application guidance, practical PCB considerations, and verified sourcing information. It is intended to help engineers identify the correct TCA5013ZAHR configuration and determine whether its 48-pin NFBGA implementation fits a given secure-card terminal design.
TCA5405RUGR - 5-Bit 1-Wire I/O Expander | Texas Instruments
The Texas Instruments TCA5405RUGR is a 5-bit, self-timed, single-wire output expander with a 1.65 V to 3.6 V supply range, eight pins, and a compact 1.5 mm × 1.5 mm X2QFN RUG package. It is designed to add five controlled outputs to a portable embedded system while requiring only one communication line from the master device. The low-voltage operating range makes the device especially suitable for battery-powered and low-voltage mobile equipment. An output expander is an interface IC that increases the number of controllable outputs available from a microcontroller or other host device. The TCA5405 belongs to the I/O expander hierarchy, where a serial data input causes a group of output channels to change state according to a timing-controlled protocol. Unlike a conventional parallel GPIO port, this device uses a self-timed serial protocol synchronized to an internal clock, reducing the number of host interface signals required. The primary features of the TCA5405RUGR include five output channels, a wide 1.65 V to 3.6 V VCC operating range, a single-wire input, and a self-timed serial data protocol. Its 0.5 mm terminal pitch and 1.5 mm × 1.5 mm body support compact PCB layouts. The manufacturer specifies an operating temperature range of -40°C to +85°C, making the device suitable for industrial and extended-temperature portable applications when the surrounding system meets its electrical and mechanical requirements. In operation, the master device establishes the bit period during a Setup phase. The TCA5405 then uses that timing information to control the five outputs without requiring a separate clock line. This self-timed architecture simplifies connections in space-constrained systems, although the host firmware must generate the required waveform accurately. The protocol timing, output behavior, and electrical limits should be implemented according to the timing diagrams in the Texas Instruments manufacturer datasheet. Typical applications include portable media players, cellular phones, personal digital assistants, and other low-voltage systems in which a host controller needs extra discrete outputs. The device can expand an output-limited controller, support controlled indicators or peripheral signaling, and reduce the pin count required from the host integrated circuit. Its small RUG package is particularly useful when component area and routing density are more important than a large through-hole footprint. A key design consideration is the relationship between supply voltage, output behavior, and the master-generated timing waveform. Keep the single data trace short, provide a stable supply, and validate the Setup and output timing over the full operating-temperature range. Do not assume that a cross-reference device with a similar function is pin-to-pin compatible; confirm package geometry, pin assignment, supply range, and protocol timing before making a replacement. This product summary organizes the TCA5405RUGR function, voltage limits, package details, replacement constraints, comparison points, and application guidance into one engineering reference. It emphasizes the information needed to assess footprint reuse, interface timing, low-voltage operation, and the distinction between a functional substitute and a true drop-in replacement.
TCA6408PW - 8-Bit I2C I/O Expander | Texas Instruments
The Texas Instruments TCA6408PW is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PW is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PW uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PW procurement and PCB drop-in decisions efficiently.
TCA6408PWR - 8-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
The Texas Instruments TCA6408PWR is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PWR is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PWR uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PWR procurement and PCB drop-in decisions efficiently.
TCA6416ARTWR - 16-Bit I2C I/O Expander with Voltage Translation | TI
The Texas Instruments TCA6416ARTWR is a 16-bit translating I2C/SMBus I/O expander with 1.65V to 5.5V operation, 400 kHz Fast Mode I2C support, voltage translation between host and port banks, and an open-drain interrupt output, housed in a 24-pin WQFN (RTW) 4x4 mm package with exposed thermal pad. An I/O expander is a category of bus-interface IC that uses a serial protocol (typically I2C or SPI) to add parallel general-purpose input/output pins to a host microcontroller whose native GPIO count is insufficient. Architecturally the TCA6416ARTWR sits beneath the "I2C peripheral" hierarchy: it is a slave I2C device that decodes SCL/SDA traffic, drives 16 quasi-bidirectional I/O ports, and exposes a polarity-inversion register, configuration register, input/output register, and a maskable interrupt. Voltage translation allows a 1.8V host MCU to switch 5V external loads without level-shifters, which is essential when interfacing legacy industrial or LED-driver peripherals. Key features include 16 individually configurable I/O bits, hardware-address pins (A0/A1/A2) for up to 8 devices on one bus (128 total ports), an active-low RESET input, an open-drain INT output that signals input-state changes, and 5V tolerant I/O ports with 25 mA sink capability per pin. The WQFN-24 (RTW) 4x4 mm package offers a low 0.8 mm height, suitable for space-constrained handheld and embedded designs. The TCA6416ARTWR implements a write-then-read protocol where the host writes a command byte to select the target register (Input, Output, Polarity Inversion, or Configuration), then reads or writes the corresponding data byte. The interrupt is cleared by reading the input port register, giving firmware a clean edge-triggered event model. Internal pull-up current sources on each port line enable direct connection to switches or buttons without external resistors. Typical applications include expanding GPIO on portable consumer electronics, industrial control panels, IoT sensor hubs, white-goods HMI boards, and any design where a low-pin-count MCU (e.g., a 32-pin Cortex-M0) needs additional buttons, LEDs, or relay drivers. It is frequently paired with low-pin-count MCUs to keep BOM cost down. When designing with this device, place 0.1 uF decoupling capacitors close to VCCI and VCCP supply pins, keep the I2C SCL/SDA traces short, and ensure pull-up resistors (typically 4.7 kohm at 400 kHz) are sized against bus capacitance. The RESET pin should be tied to VCCI through a 10 kohm resistor unless driven by the host. This page synthesizes verified distributor stock, drop-in pin-compatible alternatives, and practical design notes not consolidated in the manufacturer datasheet, helping engineers shorten component selection time and avoid sourcing risk for production builds.
TCA6416PW - 16-Bit I2C I/O Expander | Texas Instruments
Texas Instruments TCA6416PW is a 16-bit I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, 400 kHz bus support, interrupt output, reset control, and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose I/O ports to a host microcontroller through a two-wire serial interface, reducing the number of GPIO pins required in compact embedded systems. An I2C I/O expander is a type of interface IC and serial port expander that sits between a host processor and external digital lines. Its position in the hierarchy is I2C I/O expander > serial I/O expander > interface IC > semiconductor. The device is useful when a design needs more input, output, or bidirectional GPIO resources than the host controller can provide directly. Key features include 16 configurable I/O ports, bidirectional voltage-level translation through the 1.65 V to 5.5 V operating range, an interrupt output for change notification, a reset input, and configuration registers. The verified product information identifies the TCA6416 as an I/O expander for general-purpose remote I/O expansion across common microcontroller families using SCL and SDA. The TCA6416PW ordering option is supplied in a 24-pin TSSOP package. The device communicates through the I2C/SMBus-compatible two-wire interface at up to 400 kHz according to DigiKey's product listing. Configuration registers allow the host software to identify inputs, outputs, and polarity behavior, while the interrupt output provides a way for the host to react to a change on a monitored port. The reset and configuration features support deterministic initialization and power-management sequencing. Typical uses include industrial control panels, sensor and actuator interfaces, communication equipment, instrumentation, and embedded systems that need additional GPIO lines. It is particularly useful when board area, connector count, or host-controller pin availability is constrained, because sixteen external digital lines are added without dedicating sixteen parallel microcontroller pins. Designers should confirm the I2C pull-up requirements, address configuration, voltage levels, and reset timing in the manufacturer datasheet. The TSSOP footprint requires careful PCB layout and adequate clearance for the 24-pin package. Firmware should also define input, output, and polarity behavior before enabling interrupt-driven event handling. The manufacturer product page and verified distributor listings provide the primary source for electrical and ordering details.
TCA6416PWR - 16-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
Texas Instruments TCA6416PWR is a 16-bit I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, 400 kHz bus support, interrupt output, reset control, and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose I/O ports to a host microcontroller through a two-wire serial interface, reducing the number of GPIO pins required in compact embedded systems. An I2C I/O expander is a type of interface IC and serial port expander that sits between a host processor and external digital lines. Its position in the hierarchy is I2C I/O expander > serial I/O expander > interface IC > semiconductor. The device is useful when a design needs more input, output, or bidirectional GPIO resources than the host controller can provide directly. Key features include 16 configurable I/O ports, bidirectional voltage-level translation through the 1.65 V to 5.5 V operating range, an interrupt output for change notification, a reset input, and configuration registers. The verified product information identifies the TCA6416 as an I/O expander for general-purpose remote I/O expansion across common microcontroller families using SCL and SDA. The TCA6416PWR ordering option is supplied in a 24-pin TSSOP package. The device communicates through the I2C/SMBus-compatible two-wire interface at up to 400 kHz according to DigiKey's product listing. Configuration registers allow the host software to identify inputs, outputs, and polarity behavior, while the interrupt output provides a way for the host to react to a change on a monitored port. The reset and configuration features support deterministic initialization and power-management sequencing. Typical uses include industrial control panels, sensor and actuator interfaces, communication equipment, instrumentation, and embedded systems that need additional GPIO lines. It is particularly useful when board area, connector count, or host-controller pin availability is constrained, because sixteen external digital lines are added without dedicating sixteen parallel microcontroller pins. Designers should confirm the I2C pull-up requirements, address configuration, voltage levels, and reset timing in the manufacturer datasheet. The TSSOP footprint requires careful PCB layout and adequate clearance for the 24-pin package. Firmware should also define input, output, and polarity behavior before enabling interrupt-driven event handling. The manufacturer product page and verified distributor listings provide the primary source for electrical and ordering details.
TCA6416PWT - 16-Bit I2C I/O Expander | Texas Instruments
Texas Instruments TCA6416PWT is a 16-bit translating I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, interrupt output, reset input, and configuration registers in a 24-pin TSSOP package. It expands a serial I2C or SMBus connection into 16 general-purpose input/output ports, reducing the number of host-controller pins required by boards containing buttons, LEDs, logic signals, or control lines. An I/O expander is an interface IC that sits between a host processor and peripheral GPIO devices. The I2C or SMBus interface carries commands and register data over a compact serial bus, while the parallel port pins provide individually controlled digital connections. In the product hierarchy, the TCA6416PWT is an I/O expander, a serial-interface peripheral controller, and ultimately an integrated circuit used to extend digital input/output capacity. The device supports operation from 1.65 V to 5.5 V and provides voltage-level translation between the host bus and external GPIO circuitry. According to the Texas Instruments product page, it includes interrupt, reset, and configuration registers. The open-drain interrupt output indicates that an input state differs from the corresponding Input Port register state, allowing the host to avoid continuous polling. The RESET pin initiates the same reset and initialization sequence as power-on reset. Communication with the TCA6416PWT is supported at I2C/SMBus rates up to 400 kHz. The translated serial interface lets a host operating at one logic level communicate with attached circuitry operating at another voltage level within the device's specified operating range. This is particularly useful in compact industrial, communications, consumer, and embedded-control products where the controller has too few direct GPIO pins. TCA6416PWT applications include remote push-button panels, LED status indicators, relay-control interfaces, sensor digital outputs, and general board-level GPIO expansion. Designers can configure ports as inputs or outputs through the device registers, read input states, and receive an interrupt when a monitored input changes. The 24-pin TSSOP package is suitable for conventional surface-mount PCB assembly and offers a practical pin count for a 16-port device with serial control and interrupt support. When laying out the circuit, place the device close to the connector or controlled circuitry reached by the 16 port lines, while keeping the I2C bus routing short and away from high-current switching paths. Confirm pull-up resistor requirements, address configuration, logic thresholds, and the open-drain interrupt connection in the manufacturer datasheet. This page combines the device specifications, sourcing guidance, drop-in alternatives, comparison data, and application-focused engineering guidance for faster component evaluation and PCB planning.
TCA6424ARGJR - 24-bit I2C/SMBus I/O Expander | Texas Instruments
The Texas Instruments TCA6424ARGJR is a 24-bit I2C/SMBus I/O expander housed in a 32-pin UQFN (RGJ) 5x5 mm package with an exposed thermal pad. The device operates from a 1.65 V to 5.5 V supply on the I2C/SMBus side (VCCI) and supports 1.8 V, 2.5 V, 3.3 V and 5 V tolerant I/O banks on the P-port side (VCCP). It communicates through the standard I2C interface up to 400 kHz and provides 24 general-purpose bidirectional I/O lines organized as three 8-bit ports (P0, P1, P2). An I/O expander is a category of interface IC that adds extra general-purpose digital input/output lines to a microcontroller or processor that has run out of native GPIOs. In the broader taxonomy, the TCA6424ARGJR sits at: I/O expander -> peripheral expander -> interface IC -> integrated circuit. The device addresses a fundamental I/O shortage problem in compact, GPIO-constrained designs such as mobile phones, wearables, and low-cost MCUs without resorting to a more expensive processor. Key features include an open-drain interrupt output (INT) that asserts whenever any input state differs from the corresponding Input Port register, a hardware RESET pin that re-initializes all registers without removing power, and configurable register banks that allow simultaneous access without locking. The device supports standard (100 kHz) and fast (400 kHz) I2C modes and provides three hardware address pins (A0, A1, A2), allowing up to eight devices on the same I2C bus for a total of 192 I/O lines. Typical applications include adding keypad scanning, LED indicators, push-button monitoring, and GPIO expansion in cell phones, media players, industrial HMI panels, gaming consoles, and infotainment systems. The wide voltage tolerance (1.65 V to 5.5 V) makes it particularly useful when bridging a 1.8 V SoC to legacy 5 V peripherals. When designing with this part, ensure the VCCI supply is present whenever the device is communicating; the P-port voltage (VCCP) may be lower than VCCI. Place 0.1 uF decoupling capacitors close to both VCCI and VCCP pins. If multiple TCA6424A devices share the bus, assign unique A0/A1/A2 addresses and pull the INT outputs together or read each individually to avoid contention. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The UQFN-32 (RGJ) package footprint, configurable register banks, and RESET pin distinguish the TCA6424ARGJR from lower-cost expanders such as the TCA6408A or PCF8575.
TCA8418RTWR - 18-Bit 1MHz Keypad Scanner | Texas Instruments
Texas Instruments TCA8418RTWR is an 18-bit I2C/SMBus keypad scanner and GPIO expander with a 1.65 V to 3.6 V operating range, 1 MHz bus speed, interrupt and reset functions, and support for as many as 80 keys. The device is supplied in a 24-pin WQFN RTW package measuring 4 mm by 4 mm. Its 18 general-purpose I/O lines can be configured as eight keypad rows and ten columns, while integrated pullup resistors simplify attached passive key matrices. A keypad scanner is an interface IC that detects button presses and reports their locations through a serial bus. The TCA8418 belongs to the broader GPIO expander and human-machine-interface controller hierarchy. It periodically scans matrix inputs, manages event and debounce functions, and signals the host through an interrupt output. This allows a microcontroller or application processor to read one or more key states over I2C instead of dedicating individual input pins to every switch. The principal feature set includes 18 configurable I/O pins, eight-row by ten-column keypad support, up to 80 keys, 1 MHz I2C/SMBus operation, and integrated ESD protection. A dedicated interrupt output reduces the need for continuous host polling, while a reset input supports deterministic initialization. The 24-pin WQFN package also includes an exposed pad, allowing the PCB to provide a low-impedance thermal and electrical ground connection according to the manufacturer's land-pattern requirements. Technically, the device is designed for low-voltage embedded systems whose keypad capacitance and leakage characteristics suit the integrated scanning circuitry. The operating range of 1.65 V through 3.6 V supports connection to common embedded processor I/O voltages. Its 1 MHz serial interface capability provides higher communication bandwidth than slower standard-mode-only keypad controllers, although the host bus, pullups, capacitance, and firmware must all support the selected operating rate. Typical uses include portable consumer equipment, personal digital assistants, portable audio and video products, and smartphones, as identified by the manufacturer. It can also manage compact numeric keypads, function buttons, menu controls, and general-purpose digital input/output lines in industrial panels or embedded control heads. The interrupt architecture is particularly useful in battery-powered equipment because it allows the processor to remain idle between key events rather than poll the keypad continuously. PCB implementation should prioritize short I2C routing, correct pullup placement, exposed-pad solderability, and protection from conductive contamination around the keys. Confirm the exact pin assignments and pin multiplexing options in the manufacturer pin-description table before assigning rows, columns, GPIOs, interrupt, reset, or ground functions. Avoid adding external row or column pullups unless the selected operating mode or application requires them, because the device already incorporates integrated pullup circuitry. This product page consolidates the manufacturer's key specifications, verified sourcing information, pin-package constraints, and application guidance into a single engineering reference. It also separates confirmed electrical facts from parameters that require consultation of the full TCA8418 datasheet, helping designers plan keypad scans, bus connections, PCB layout, and firmware integration before layout release.
TCA8424RHAR - 24-Bit I2C Keypad Scanner | Texas Instruments
The Texas Instruments TCA8424RHAR is a low-voltage 8×16 keypad scanner with a 24-bit key-state register, a 1.65 V to 3.6 V supply range, and an I2C/SMBus-compatible interface rated for operation up to 1 MHz. The device is packaged in a 40-pin VQFN measuring 6 mm × 6 mm and supports as many as 128 keys. An interrupt output allows the host processor to be notified when the scanned key matrix changes, reducing unnecessary polling and helping conserve power in portable and embedded systems. A keypad scanner is an interface integrated circuit that converts the electrical state of a matrix of switches into a compact digital status value. In the system hierarchy, it belongs to the interface-controller family within integrated circuits, alongside I2C and SMBus peripherals, GPIO expanders, and human-interface-device controllers. The TCA8424RHAR is designed to sit between a mechanical keypad matrix and an embedded host such as a microcontroller, leaving the host to interpret recognized key events and perform application-specific actions. The principal feature is support for an 8×16 matrix, providing 128 scanning positions in a compact physical footprint. Its 24-bit key-state register provides a defined digital representation of the matrix, while the interrupt signal supports event-driven host communication. Operation from 1.65 V to 3.6 V makes the scanner suitable for low-voltage embedded systems, and the 1 MHz interface capability allows it to operate on a faster shared serial bus when host timing and bus capacitance permit. The device combines matrix scanning with an I2C/SMBus-compliant host interface and HID-oriented keyboard-scanner functionality. These characteristics make it useful where a conventional matrix requires many host GPIO pins or where a dedicated serial keypad controller simplifies firmware. The scanner limits the host interface to the serial bus and interrupt line rather than requiring one GPIO input for every key position. Configuration and status reporting are handled through the serial interface, while the interrupt output indicates that the matrix state requires attention. Typical applications include consumer keypads, security-access panels, industrial control membranes, portable instruments, and compact human-interface panels. A product with 128 possible switch positions can use the full scanner capacity, while systems with fewer switches can leave unused matrix positions unconnected according to the manufacturer's implementation guidance. The device can also complement a touchscreen controller by providing physical-key input alongside touch input when a product requires both interaction methods. Layout planning should account for the 40-pin VQFN footprint, exposed thermal pad, decoupling requirements, and signal integrity of the I2C bus. Place the input and interface bypass capacitors close to their corresponding pins, route the interrupt trace away from high-current switching nodes, and confirm pull-up values against the bus voltage, capacitance, and operating speed. Because the 1 MHz rating is a maximum interface capability rather than a requirement for every design, use a conservative bus rate when signal-integrity margins are limited. This product page combines the manufacturer’s device capabilities with package, sourcing, interface, and design information in one engineering-focused reference. It also identifies the limits of the available substitution evidence: no same-package, pin-to-pin replacement is asserted unless its electrical characteristics and land pattern have been independently confirmed.
TCA9509RVHR - 2-Bit I2C Level Translator | Texas Instruments
The Texas Instruments TCA9509RVHR is a 2-bit level-translating I2C/SMBus buffer and repeater operating up to 400 kHz, with an internal 1 mA pull-up current source and an 8-pin X2QFN package measuring 1.6 mm by 1.6 mm. It is designed to isolate voltage domains while preserving bidirectional bus communication. An I2C level translator is an interface IC that connects logic operating at different voltage levels on the same serial bus. Its position in the hierarchy is I2C repeater, level translator, interface IC, and ultimately semiconductor. This bidirectional separation helps prevent low-voltage devices from receiving signals that exceed their input limits and helps keep high-voltage devices from exposing low-voltage nodes to excessive voltage. The principal features are two independently level-translated bus channels, operation up to 400 kHz, an internal 1 mA current source, and support for both I2C and SMBus signaling. The small X2QFN package supports compact PCB layouts where board area is constrained. Its buffer function can also isolate capacitive loading between bus segments and improve signal integrity in multi-board or multi-device systems. The B-side drivers use SMBus-compatible I/O levels, while the A-side uses current sensing to identify LOW states and avoid bus lock-up. The A-side includes the internal 1 mA current source for pull-up support. This arrangement accommodates smaller LOW-state voltage swings while retaining bidirectional data transfer, which is important when connecting peripherals with different supply voltages. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus management interfaces, compact industrial modules, embedded instrumentation, and systems that divide a long I2C bus into shorter electrically isolated segments. The device is particularly useful when cables, connectors, or PCB routing introduce capacitance between bus nodes. When laying out the circuit, treat the A-side and B-side pull-up networks as separate domains and confirm that the external pull-up strength works with the intended bus voltage and capacitance. Avoid adding unnecessary capacitance near the small package, and verify signal rise times at the maximum intended I2C clock rate. Bus timing and voltage margins remain the responsibility of the final board design. This page combines the manufacturer product information, ordering data, documented cross-reference details, packaging characteristics, and practical design guidance in one engineering-focused view. It also distinguishes true pin-compatible interchange from merely similar I2C switching devices, helping designers make a replacement decision without assuming that equal functionality guarantees equal footprint or pin behavior.
TCA9517DGKR - I2C Bus Repeater Level Translator | TI
The Texas Instruments TCA9517DGKR is a 2-channel, bidirectional level-translating I2C bus repeater and buffer supporting 400 kHz (Fast-mode) I2C and SMBus operation, with A-side supply from 0.9 V to 5.5 V and B-side supply from 2.7 V to 5.5 V, housed in an 8-pin VSSOP (DGK) package. A level-translating I2C bus buffer is an interface IC that sits between two segments of an I2C or SMBus, electrically isolating the bus capacitance and logic levels on each side. In the interface IC hierarchy, it belongs to the signal buffer/repeater family of level translators, which sit above simple transistors and below full protocol bridges. By segmenting the bus, the repeater allows longer buses and more devices than the I2C standard capacitance limit would otherwise permit. Key features include support for both standard-mode (100 kHz) and fast-mode (400 kHz) I2C signaling, an enable (EN) pin for bus isolation and power sequencing, and powered-off high-impedance I2C pins that effectively remove the device from the bus when either supply is absent. The TCA9517 also incorporates an acceleration feature that speeds up the rising edge of SDA and SCL on the B side. Architecturally, the TCA9517 uses two distinct driver types. The A-side drivers operate from 0.9 V to 5.5 V and drive more current without requiring the buffered-low static offset voltage, so a low on the B side translates to a nearly 0 V hard low on the A side. This accommodates the smaller voltage swings of lower-voltage logic such as 1.2 V or 1.8 V I2C peripherals. The B side retains the static voltage offset needed for hot-swapping and rise-time acceleration. Typical applications include I2C bus expansion in industrial automation, server and telecom backplane management (SMBus), and level translation between 1.8 V microcontrollers and 3.3 V sensors or EEPROMs. Design consideration: the A-side output can sink more current than a plain MOSFET translator, so pay attention to total bus capacitance per segment; keep pull-up resistor values sized per segment rather than one pair for the whole bus. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
TCA9517DGKRQ1 - Automotive I2C Level-Shifting Buffer | TI
The Texas Instruments TCA9517DGKRQ1 is an automotive-grade, 2-bit level-translating I2C/SMBus buffer/repeater operating at up to 400 kHz, housed in an 8-pin VSSOP (DGK) package and qualified to AEC-Q100 for -40C to +125C operation. An I2C bus buffer, also called a level translator or bus repeater, is an interface IC that sits between two segments of an I2C or SMBus serial bus. Its role in the interface IC hierarchy is to isolate bus capacitance, allowing longer or more heavily loaded buses, and to translate logic voltage levels between devices powered from different supply rails, such as a 1.8V microcontroller talking to 5V peripherals. Key features include bidirectional voltage-level translation between low voltages down to 0.9 V on side A and 2.7 V to 5.25 V on side B, support for both standard-mode (100 kHz) and fast-mode (400 kHz) I2C plus SMBus, and a powered-off high-impedance state that isolates both bus segments when either supply rail is absent. The enable (EN) pin provides additional bus control, and open-drain I/O structures preserve the wired-AND nature of I2C. Technically, the TCA9517-Q1 drives both sides of the bus, refreshing rise times and removing the cumulative load of stubs and cables. Unlike passive FET level shifters, it does not trade drive strength for level translation, so clock stretching and multi-master arbitration are preserved. It supports up-translation, down-translation, and same-level buffering. Typical applications include automotive body electronics and infotainment I2C bus extension, PMBus/SMBus power-supply management in industrial systems, and level translation between 1.8V or 3.3V MCUs and 5V sensors or EEPROMs. Design consideration: because the device drives each side actively, do not connect the A and B sides to the same bus segment, and keep EN tied low until both supply rails are stable to avoid bus latch-up during power sequencing. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone. Pricing shown as of 2026-10-19.
TCA9517DR - Level-Shifting I2C Bus Repeater | Texas Instruments
The Texas Instruments TCA9517DR is a 2-bit level-translating I2C/SMBus bus buffer supporting 400 kHz Fast Mode operation, with an A-side supply range of 0.9 V to 5.5 V and a B-side supply range of 3.0 V to 5.5 V, housed in an 8-pin SOIC (D) package. An I2C bus buffer (also called a bus repeater or level translator) is an interface IC that sits between two segments of an I2C or SMBus serial bus. Its role in the interface IC hierarchy is to electrically isolate the two segments while translating signal levels between devices powered at different voltages, allowing low-voltage microcontrollers to communicate safely with higher-voltage peripherals. A buffer also isolates bus capacitance, so each side can drive longer traces or more devices than a single unbuffered bus would allow. Key features include fully bidirectional level translation with no direction-control pin, a low-level input on the A-side set at 0.3 x VCCA that accommodates smaller voltage swings of lower-voltage logic, and a powered-off high-impedance state on all pins so the part never loads the bus when unpowered. According to the TCA9517 datasheet, the A-side drivers operate from 0.9 V to 5.5 V, drive more current than B-side drivers, and do not require a buffered low or static offset voltage, producing a nearly 0 V hard low on the A-side. Architecturally, the TCA9517 uses open-drain drivers with rise-time support rather than a static 0.5 V low offset on the A-side, distinguishing it from the older PCA9517 generation. The 230 ns maximum propagation delay preserves I2C Fast Mode timing margins at 400 kHz, and the two channels translate both SDA and SCA lines simultaneously. Typical applications include connecting 1.8 V or 3.3 V MCU I2C ports to 5 V EEPROMs, sensors, and RTCs in industrial and telecom equipment, isolating bus capacitance in long backplane runs, and buffering densely loaded SMBus segments. Design consideration: keep the A-side connected to the lower-voltage, higher-capacitance segment; the B-side static 0.5 V offset requires pairing buffers B-side to A-side in cascaded topologies. This page synthesizes distributor pricing, verified drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.