Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
ATMXT112S-MAUR - 112-Node maXTouch Touch Controller | Microchip
The Microchip Technology ATMXT112S-MAUR is a maXTouch S-Series capacitive touchscreen controller IC with 112 mutual-capacitance sensing nodes, housed in a 32-pin UQFN (4x4 mm) package. It supports screens up to 3.5 inches and delivers smartphone-grade multi-touch performance with integrated noise mitigation for operation in noisy environments. A capacitive touch controller is a mixed-signal IC that measures tiny capacitance changes on a touch sensor grid, converts them into touch coordinates, and communicates them to a host processor. In the system hierarchy, a touchscreen controller sits between the touch sensor (ITO pattern on glass or film) and the host MCU or application processor, forming part of the human-machine interface subsystem alongside display drivers and haptic feedback devices. Key features of the ATMXT112S-MAUR include its 112-node sensing matrix for dense electrode layouts, the maXTouch S-Series architecture optimized for small displays up to 3.5 inches, and an advanced noise mitigation system that rejects interference from display drivers and chargers. The device integrates acquisition logic and post-processing, offloading touch detection from the host CPU. Technically, the maXTouch S-Series uses a proprietary acquisition engine with mutual-capacitance scanning and built-in self-calibration. Configuration data is stored on-chip in nonvolatile memory, and communication with the host uses an I2C-compatible interface. The device supports moisture and gloved-finger handling modes and provides robust reporting rates for responsive user interfaces. Typical applications include feature phone touchscreens, handheld game consoles, digital still cameras, portable GPS navigation devices, and small industrial HMI panels. Any battery-powered product with a 3.5-inch or smaller capacitive display benefits from the low-power touch wake-up and high noise immunity. Design consideration: because touch performance depends strongly on the sensor pattern and panel stack-up, use Microchip's maXTouch configuration tooling and reference sensor designs; improper grounding near display VCOM lines is the most common source of false touches. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ATMXT1386-Z2UIR - maXTouch 1386-Node Touch Controller | Microchip
The Microchip Technology ATMXT1386-Z2UIR is a capacitive touch screen controller from the maXTouch product platform, implementing a 1386-node multi-chip solution (4 chips) that combines charge-transfer acquisition technology with a powerful 32-bit AVR microcontroller core. It is supplied in a 64-terminal HVQCCN (LCC64) surface-mount package. A capacitive touch controller is an interface IC that measures changes in capacitance across a touch sensor grid, converts those measurements into touch coordinates, and communicates them to a host processor. Within the semiconductor hierarchy it sits under data acquisition ICs, specifically touch screen converters and controllers, and forms part of the broader human-machine interface (HMI) signal chain that includes the sensor glass, the controller IC, and the host firmware. Key differentiating features include the 1386-node acquisition capacity, which supports large-format touch panels with many simultaneous sensing channels; the multi-chip architecture that lets four devices cooperate on a single panel; and the integrated 32-bit AVR processing that performs filtering and gesture detection on-chip, reducing host CPU load. The maXTouch platform firmware can be updated in-system, enabling tuning for different glass stack-ups. The charge-transfer acquisition technique offers strong signal-to-noise performance against display noise, which is important for designs where the touch sensor is integrated into or placed close to an LCD. On-chip AVR computation allows advanced touch features such as multi-touch tracking, palm rejection, and moisture compensation depending on the configured firmware. Typical applications include industrial HMI touch panels, large-format touch screens for appliances and kiosks, medical equipment control surfaces, and embedded systems requiring robust multi-touch input on medium-to-large sensor arrays. A key design consideration is that this device has been discontinued by Microchip; the manufacturer officially recommends the ATMXT1066T2 touch controller as the alternative for new designs, so availability should be confirmed before committing to a BOM. This page synthesizes distributor listings, manufacturer product-page data, and cross-reference findings, including drop-in-replacement guidance and procurement notes not found in the manufacturer datasheet.
ATMXT1386E-Z2U - maXTouch 1386-Node Touch Controller | Microchip
The Microchip Technology ATMXT1386E-Z2U is a capacitive touchscreen controller from the maXTouch product platform, implementing a 1386-node multi-chip solution built from four chips. It combines Atmel's patented QMatrix charge-transfer capacitive sensing method with a powerful 32-bit AVR microcontroller, and supports up to 16 simultaneous touches with fast response time. A capacitive touchscreen controller is a type of sensor interface IC that measures mutual capacitance changes across a touch sensor grid, classifies and tracks finger touches, and reports coordinates to a host processor. Within the system hierarchy, it sits in the signal chain between the touch sensor (a patterned ITO or similar electrode layer on the display) and the host MCU or application processor, forming part of the broader human-machine interface (HMI) subsystem. Key features include the 1386 mutual-capacitance node count, which suits medium-to-large touch panels; the patented charge-transfer acquisition engine, which delivers high signal-to-noise measurement accuracy; and multi-touch tracking of up to 16 touches. The high-performance architecture enables fast response and unlimited-touch reporting up to the 16-touch limit, making the device suitable for demanding interactive displays. Technically, the mXT1386E uses a unique charge-transfer acquisition engine implementing the QMatrix capacitive sensing method patented by Atmel. Coupled with a state-of-the-art 32-bit AVR CPU, the entire touchscreen sensing solution can measure, classify and track finger touches with a high degree of accuracy. As a multi-chip (4-chip) solution, the family coordinates sensing across the node array within one firmware-managed platform. Typical applications include tablet and e-reader touchscreens, industrial HMI panels, and consumer electronics displays requiring robust multi-touch performance with gloved-hand and noise immunity characteristic of the maXTouch platform. Design consideration: this part is a multi-chip solution, so verify board space, mechanical stacking and firmware/configuration compatibility against the replacement controller before redesign. Note that Microchip has officially recommended the ATMXT1066T2 as the alternative touch controller for this family. This page synthesizes distributor sourcing data, the manufacturer-recommended replacement, and practical design notes not found in the manufacturer datasheet.
ATMXT1386E-Z2UR - maXTouch 1386-Node Touch Controller | Microchip
The Microchip Technology ATMXT1386E-Z2UR is a 1386-node capacitive touch screen controller from the maXTouch product platform, implemented as a multi-chip solution combining four chips that pair charge-transfer acquisition technology with a powerful 32-bit AVR microcontroller core. It supports up to 16 simultaneous touches with fast response, and communicates with the host processor through either an I2C-compatible interface or a USB interface, though only one interface should be used in any single design. A capacitive touch controller is an interface IC that measures changes in capacitance across a touch sensor grid, applies touch-detection and noise-immunity algorithms, and reports touch coordinates to a host MCU or application processor. Within the semiconductor hierarchy it sits under touch screen controllers, a subcategory of sensor interface ICs in the maXTouch family spanning small single-chip solutions up to large multi-chip nodes for large-format touch panels. Key differentiating features include the very high 1386-node sensor channel count, support for up to 16 concurrent touch points, self- and mutual-capacitance charge-transfer acquisition, and dual host communication options (I2C-compatible or USB). The multi-chip architecture scales acquisition bandwidth for large touch panels used in industrial HMI and commercial display designs. Technically, the ATMXT1386E integrates four chips operating as one synchronized controller, with the 32-bit AVR execution core running Microchip's maXTouch firmware for touch detection, palm rejection, and noise filtering. Configuration is typically loaded into EEPROM/flash by the host at power-up, allowing tuning of sensitivity and gesture behavior without firmware changes. Typical applications include large-format industrial touch monitors, commercial kiosks and point-of-information terminals, and multi-touch human-machine interfaces where many sensor nodes and reliable multi-touch detection are required. A key design consideration is that Microchip has flagged this product for end-of-life: the manufacturer-recommended alternative touch controller is the ATMXT1066T2, so new designs should target that device while the ATMXT1386E family remains available for last-time-buy and service inventory. This page synthesizes distributor sourcing, the manufacturer-recommended successor, and practical design guidance not found in the standard datasheet listing.
ATMXT1386XES-CHPSET2 - 1386-Node maXTouch Touch IC | Microchip
The Microchip Technology ATMXT1386XES-CHPSET2 is a 1386-node capacitive touch screen sensor IC solution from the maXTouch product platform, supplied as a multi-chip set of 4 chips. By combining charge-transfer touch sensing technology with a powerful 32-bit AVR microcontroller core, this device delivers large-format projected-capacitive touch detection with Microchip's maXTouch signal-processing algorithms. A capacitive touch controller is a specialized mixed-signal IC that scans a matrix of mutual-capacitance nodes on a touch sensor panel, converts capacitance changes into digital coordinates, and reports touch positions to a host processor over a digital interface. In the product taxonomy, this device belongs to Interface ICs > capacitive touch sensors, which sits within the broader families of human-interface devices, sensor interfaces, and mixed-signal integrated circuits. Key characteristics of the ATMXT1386 family include the 1386-node sensing capacity, an on-chip 32-bit AVR processing core for autonomous touch acquisition, and maXTouch filtering that supports gloved operation, passive stylus, and water-rejection behavior typical of the platform. The XES-CHPSET2 ordering code denotes a chip-set (multi-chip) configuration rather than a single monolithic die, which system designers must account for in PCB partitioning. Technically, the charge-transfer acquisition engine periodically drives and senses the electrode matrix, while the embedded AVR firmware applies noise filtering, baseline tracking, and touch classification. This architecture offloads all touch processing from the host, requiring only configuration data and touch reports over the communication interface. Typical applications include large-format touchscreen displays for industrial human-machine interfaces (HMI), point-of-information kiosks, and other commercial touch systems that previously used this high-node-count controller. A key design consideration: Microchip lists the ATMXT1066T2 as the recommended alternative touch controller for the ATMXT1386, since this multi-chip solution is obsolete and no longer recommended for new designs. This page synthesizes distributor availability data, the manufacturer's recommended migration path, and drop-in alternative analysis not found on the Microchip product page alone.
ATMXT1664S1-CU - maXTouch Touchscreen Controller IC | Microchip Technology
The Microchip Technology ATMXT1664S1-CU is a maXTouch capacitive touchscreen controller IC from the maXTouch S-series family, supporting 1664 mutual-capacitance sensing nodes for projected-capacitive touch screens, supplied in a compact surface-mount package with RoHS3-compliant construction. According to distributor listings including DigiKey and Octopart, the device is classified as a Touch Screen Controller (IC SENSOR MAXTOUCH). A capacitive touchscreen controller measures mutual capacitance across a matrix of transmit and receive electrodes on the touch sensor. When a finger or passive stylus approaches the intersection of electrodes, local capacitance changes; the controller scans the matrix, converts the capacitance deltas to touch coordinates, applies gesture and noise filtering, and reports touch data to a host processor over an interface such as I2C or SPI. Touchscreen controllers sit within the broader hierarchy of sensor interface ICs and human-machine interface (HMI) semiconductors. The maXTouch S-series architecture integrates a high-performance acquisition engine with differential charge amplifiers, a configurable scan sequencer, and an embedded MCU core executing Microchip-supplied object-based firmware. Self- and mutual-capacitance fusion enables gloved-hand operation and water rejection, while frequency-hopping acquisition combats charger and display noise - a critical requirement for thin bezel tablets, POS terminals, and automotive HMI panels. Technical strengths of the family include high node counts supporting large-format touch panels, the maXTouch object model allowing configuration of key timings and thresholds via I2C registers, and mature firmware tooling through Microchip's maXTouch studio ecosystem. The S1 model designation reflects the firmware/feature configuration of the 1664-node silicon. Typical applications include 7-inch to 13-inch capacitive touchscreens in tablets, human-machine interfaces for white goods and appliances, point-of-sale and ticketing terminals, smart-home wall panels, and industrial operator panels where multi-touch and robust noise immunity are required. When designing with this controller, allocate a clean low-noise analog supply for the sensing core and route the sensor flex connector away from switching regulators; charger-mode noise often dominates real-world touch performance and must be verified with the intended display and charger pair. This page synthesizes distributor sourcing data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-19.
ATMXT1664S1-CUR - maXTouch 1664-Channel Touch Controller | Microchip
The Microchip Technology ATMXT1664S1-CUR is a maXTouch S Series capacitive touchscreen controller with 1664 mutual-sense channels, built on a 32-bit AVR microcontroller architecture, supplied in a reflow-capable surface-mount package for large-format touchscreen devices. A capacitive touch screen controller is an interface IC that measures capacitance changes across a grid of sensor electrodes to detect finger and stylus positions. Within the system hierarchy, it sits between the raw touch sensor (ITO pattern on glass or film) and the host application processor, converting analog charge-transfer measurements into touch coordinates over a digital interface. The maXTouch family from Microchip (originally Atmel) is a widely adopted line of such controllers used from wearables to large interactive displays. The ATMXT1664S1 belongs to the S Series, which brings the maXTouch architecture to large touchscreen devices. Its 1664 sensing channels support high electrode counts typical of large-format panels, while the integrated 32-bit AVR core performs on-chip acquisition, filtering, and gesture processing, offloading the host processor. Multiple S Series devices can operate simultaneously to drive very large screens, a scalability feature documented by Microchip for this family. The suffix structure of the part number encodes ordering options such as temperature grade and packaging (-CUR indicates a reflow-eligible, RoHS-grade ordering variant per Microchip nomenclature). As with all maXTouch parts, configuration of sensitivity, report rate, and multi-touch behavior is performed via firmware objects downloaded to the controller, allowing one PCB design to be tuned for different sensor stacks. Typical applications include large interactive displays, industrial HMI panels, point-of-information kiosks, and premium consumer touch devices where high channel count and robust noise immunity near displays or chargers are required. A key design consideration is that maXTouch controllers require a configuration file matched to the specific sensor pattern and stack-up; mismatched configurations degrade linearity and report rate. Verify communication with the host over the I2C-compatible interface during bring-up. This page synthesizes distributor availability, Microchip product data, and the manufacturer-recommended replacement ATMXT1664T3 into one reference, adding drop-in alternative guidance and design notes not found in the datasheet alone.
ATMXT2952T2-C2U - maXTouch Touch Controller | Microchip
The Microchip Technology ATMXT2952T2-C2U is a maXTouch capacitive touchscreen controller IC from the mXT2952T2 family, supporting up to 2952 touch channels and display sizes up to 21 inches, aimed primarily at industrial designs and housed in a BGA package. A capacitive touchscreen controller is a mixed-signal IC that measures mutual-capacitance changes across a touch sensor grid, converts the raw charge-transfer measurements into touch coordinates and gesture information, and reports them to a host processor over a digital interface. In the system hierarchy, it sits within the human-interface / data acquisition domain: touchscreen controller -> capacitive touch sensor IC -> sensor interface IC -> mixed-signal semiconductor. Key features of the ATMXT2952T2 family include Microchip's Adaptive Sensing technology, which automatically and intelligently switches between touch operating modes based on the detected object or environment, dynamic touch classification for finger, glove, stylus, and water rejection scenarios, and a debug port for tuning (per Microchip application note QTAN0050 'Using the maXTouch Debug Port'). The device supports I2C host communication; in I2C mode the pull-up resistor on the DBG_SS/GPIO0 shared ball is optional and present only if the ball is used as DBG_SS. The architecture pairs a charge-transfer analog front end with on-chip processing that performs self- and mutual-capacitance scanning, noise filtering, and touch classification. Adaptive Sensing allows the same controller to deliver reliable touch performance on thick cover lenses, in wet conditions, and under EMI conditions typical of industrial panels. Typical applications include industrial HMI touch panels up to 21 inches, factory automation displays, medical equipment screens, and commercial kiosk or point-of-information terminals where gloved-hand and water rejection are required. A key design consideration is the shared DBG_SS/GPIO0 ball: only one of these two functions can be selected, and the circuit must be designed accordingly; consult the manufacturer datasheet and QTAN0050 before finalizing the sensor flex pin mapping. Note that Microchip identifies ATMXT2952TD as the recommended alternative touch controller for the ATMXT2952T2, which is relevant for new designs and long-term supply planning. This page synthesizes distributor availability, the recommended replacement, and design guidance not consolidated in the manufacturer datasheet.
ATMXT768E-ABR - maXTouch Touchscreen Controller | Microchip
The Microchip Technology ATMXT768E-ABR is a maXTouch mXT768E-AT mutual-capacitance touchscreen controller IC designed for projected-capacitive touchscreens of up to 10.1-inch diagonal or even larger. It belongs to Microchip's maXTouch family of capacitive touch controllers and integrates signal-acquisition, touch-decision, and host-interface functions in a single device. A projected-capacitive (PCAP) touchscreen controller is a specialized mixed-signal IC that drives excitation signals across rows and columns of a transparent ITO sensor grid and measures mutual capacitance changes at each intersection. Within the system hierarchy, it sits between the raw touch sensor laminate and the host processor, delivering pre-processed touch coordinates over a digital interface. This class of device is fundamental to modern human-machine interface (HMI) design in industrial, medical, and consumer equipment. Key characteristics of the mXT768E-AT include high responsiveness for large-format screens, support for multi-touch reporting, and Microchip's maXTouch object-based reporting architecture in which touch data is conveyed as structured objects over an I2C or SPI-compatible host interface. The device is firmware-configurable, allowing tuning of sensitivity, rejection thresholds, and gesture behavior to match specific sensor stacks. The ATMXT768E-ABR was originally targeted at tablets, industrial HMI panels, point-of-sale terminals, and medical monitors in the 7-inch to 10.1-inch class. Note that Microchip's product page indicates this part is no longer recommended for new designs and recommends the ATMXT1189TD-A as the alternative touch controller for new development. Design consideration: because the mXT768E-AT is in end-of-life transition, new designs should evaluate the ATMXT1189TD-A and verify firmware migration effort, sensor-stack compatibility, and pin mapping before committing to a layout. This page synthesizes distributor availability, cross-reference data, lifecycle status, and practical design notes not found in the manufacturer datasheet alone, helping engineers make a supply-risk-aware selection decision.
ATMXTS100-CU - maXStylus Active Stylus ASIC | Microchip
The Microchip Technology ATMXTS100-CU is a maXStylus Gen I active stylus ASIC designed for capacitive touch sensing systems, classified under Interface - Sensor, Capacitive Touch ICs and belonging to the maXTouch product series from Microchip Technology. The device ships in tape-and-reel packaging with a standard package quantity of 6,000 units per reel, and the part status is listed as Active per distributor and manufacturer data. An active stylus controller IC is a specialized mixed-signal device that implements the transmit and signal-processing functions of an active pen system, enabling a battery-powered stylus to communicate position, pressure, and hover information with a capacitive touchscreen that is driven by a companion maXTouch touch controller. Within the system hierarchy, this device sits alongside touch sensors and touch screen controllers inside the human-interface input subsystem of tablets, e-readers, signature pads, and other pen-enabled displays. Key characteristics identified from verified distributor data include the maXStylus Gen I generation designation, maXTouch series membership, capacitive touch interface classification, and active lifecycle status. This positions the ATMXTS100-CU within Microchip's established maXTouch ecosystem, which is widely deployed in commercial and industrial touchscreen designs. Architecturally, active stylus ASICs coordinate the stylus-tip signal generation and timing with the host touchscreen controller so that palm rejection, hover detection, and fine-line pen input can be achieved on standard mutual-capacitance panels. Designers typically pair the stylus ASIC with a maXTouch touchscreen controller on the host side to form a complete pen-and-touch subsystem. Typical applications include active pen input for tablets and 2-in-1 computing devices, digital signature capture terminals, and industrial touch panels requiring stylus precision. In each case the ASIC provides the dedicated stylus-side signal chain that a general-purpose MCU would struggle to replicate with equivalent latency and power efficiency. A key design consideration is that per available cross-reference information this device is generally not pin-compatible with capacitive touch sensors from competing vendors, so second-sourcing requires careful I/O voltage and interface evaluation. This page synthesizes distributor pricing channels, verified lifecycle data, and practical design notes not consolidated in the manufacturer datasheet.
ATPL230A-AKU-R - PRIME PLC Modem 128.6Kbps | Microchip
The Microchip Technology ATPL230A-AKU-R is a PRIME-compliant power line communications (PLC) base band modem IC delivering data rates up to 128.6 kbps from a 3.3 V supply in an 80-pin LQFP (12x12 mm) package. It integrates an AES-128 crypto engine, operates from -40C to +85C, and supports CENELEC-A, FCC, and ARIB frequency bands. A power line communications modem is a specialized embedded device that transmits data over existing AC mains or DC power distribution wiring, eliminating the need for dedicated communication cabling. In the system hierarchy, the ATPL230A belongs to the class of application-specific microcontrollers and communication transceivers, bridging the gap between a host MCU and the physical power-line medium via an analog front end and coupling network. Key features include full compliance with the PHY layer of the PRIME (PRoducts for Intelligent Metering Evolution) specification v1.3 and v1.4, independently selectable transmission bands up to 472 kHz, and baud rates ranging from 5.4 kbps to 128.6 kbps. Additional robust modes and frequency band extension improve link reliability in noisy grid environments, while the hardware AES-128 engine secures metering data without burdening the host processor. The ATPL230A uses a flexible architecture composed of hardware accelerators and co-processors, enabling a highly efficient PRIME PHY implementation. An SPI interface connects the modem to an external host microcontroller, which handles PRIME MAC/CON layers and application logic. This partitioning allows firmware upgrades on the host without touching the certified PHY layer. Typical applications include smart metering (electricity, gas, water), smart grid street lighting control, solar inverter communication, and building automation over mains wiring. The industrial temperature grade of -40C to +85C supports outdoor and cabinet-mounted metering equipment. When designing with this device, budget the analog front end (line driver, coupling transformer, and filters) carefully, as PHY performance in CENELEC-A, FCC, and ARIB bands depends strongly on the external network; Microchip reference designs should be followed for coupling circuitry. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ATPL250A-AKU-R - G3-PLC Power Line Modem IC | Microchip
The Microchip Technology ATPL250A-AKU-R is a G3-PLC (Power Line Communication) modem system-on-chip delivered in an 80-pin LQFP (AKU) surface-mount package, rated for the industrial temperature range of -40C to +85C and supplied in Tape & Reel (T&R) green/RoHS packaging. It integrates hardware accelerators and coprocessors that achieve a highly efficient G3 PHY layer implementation for narrowband power line communication. A power line communication modem is a communication IC that transmits data over existing AC mains or DC power lines by modulating a carrier signal onto the line, eliminating the need for dedicated wiring. Within the system hierarchy, the ATPL250A sits between the physical analog line front end and the host microcontroller, offloading the computationally demanding PHY and MAC layers of the G3-PLC standard from the application processor. G3-PLC is an open standard promoted by the G3-PLC Alliance and supported by internationally recognized standards bodies, making it the dominant PLC technology for smart grid infrastructure. Key features include flexible support for G3-PLC CENELEC, ARIB, and FCC frequency profiles, which allows one design to serve global markets with different regulatory band plans. The hardware-accelerated architecture handles OFDM modulation, forward error correction, and convolutional interleaving in dedicated logic, delivering deterministic real-time performance that a pure software implementation cannot match. The device is classified by distributors as a Network Controller & Processor IC / power line communications microcontroller. The ATPL250A implements the G3 PHY layer with hardware accelerators and coprocessors, achieving spectral efficiency and robustness over hostile power line channels characterized by multipath fading, impulsive noise, and frequency-selective attenuation. This architecture lets a companion host MCU manage application logic, metering computation, or protocol translation while the ATPL250A transparently maintains the PLC link, including adaptive tone mapping and channel estimation. Typical applications include smart metering (electricity meters and data concentrators), smart lighting control, industrial and home automation, and home energy management gateways. In a data concentrator, the ATPL250A aggregates PLC traffic from hundreds of meters onto a backhaul link, making its PHY efficiency directly responsible for network capacity. When designing with the ATPL250A, pay close attention to the analog line driver and coupling network: PCB layout of the transmit path and use of the reference design from the Atmel/Microchip user manual are critical to meeting G3-PLC Alliance interoperability and local emissions regulations. This page synthesizes verified distributor data, drop-in alternatives from the same LQFP-80 ATPL PLC family, and selection guidance not consolidated in the manufacturer datasheet. Pricing and availability were last verified on 2026-09-19.
ATPL250A-AKU-Y - G3-PLC Power Line Modem 3.3V | Microchip
The Microchip Technology ATPL250A-AKU-Y is a G3-PLC (Power Line Communication) modem microcontroller IC operating from a 3.3V supply, housed in an 80-pin LQFP (AKU) package, rated for the industrial temperature range of -40C to +85C. A power line communication modem is a specialized communication IC that transmits and receives data over existing AC mains or DC power lines, eliminating the need for dedicated wiring. It sits within the broader hierarchy of communication ICs and embedded processors: PLC modem -> telecom interface IC -> network controller -> microcontroller-class system-on-chip. G3-PLC is an open standard promoted by the G3-PLC Alliance and supported by internationally recognized standards bodies, widely deployed in smart grid infrastructure. The ATPL250A features a flexible architecture composed of hardware accelerators and coprocessors that achieve a very efficient G3 PHY layer implementation. According to the Microchip ATPL250A datasheet, the device supports G3-PLC CENELEC, ARIB, and FCC profiles, making it adaptable to regional regulatory band plans across Europe, Japan, and North America. The hardware-based PHY offloads modulation, coding, and windowing tasks from software, reducing CPU load and improving real-time determinism. This combination of flexible coprocessor architecture and multi-profile band support makes the ATPL250A a compact and highly efficient device for a wide range of smart grid applications, including smart metering (smart meters and data concentrators), street lighting control, industrial and home automation, and home area network gateways. The 80-pin LQFP provides sufficient GPIO and peripheral interfaces to host application firmware alongside the modem function. When designing with the ATPL250A, careful attention must be paid to the analog front-end coupling network between the modem and the power line, as line impedance variation directly affects achievable data rate and link reliability. Microchip provides the ATPL250A Evaluation Kit (documented in device document 00002299B) as a hardware platform for evaluating the modem and integrating it into custom designs. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet, consolidating data from DigiKey, Mouser, Octopart, and Microchip documentation as of 2026-09-19.
AX58100LT - 2/3-Port EtherCAT Slave Controller | ASIX
The ASIX Electronics AX58100LT is a 2/3-port EtherCAT Slave Controller (ESC) with two integrated Fast Ethernet PHYs, operating from a 3.3V supply and packaged in an 80-pin LQFP-EP (10x10 mm). It implements the EtherCAT slave protocol in hardware and exposes 2 or 3 PHY ports plus digital host interfaces (SPI / host bus) to an external MCU, making it one of the most integrated single-chip ESCs in its class. An EtherCAT Slave Controller is a specialized industrial Ethernet IC that handles the EtherCAT protocol (a deterministic real-time Ethernet standard originally developed by Beckhoff and standardized by the EtherCAT Technology Group) without burdening the host CPU. The EtherCAT protocol itself falls under the broader hierarchy of industrial fieldbuses -> real-time Ethernet -> industrial communication IC -> semiconductor. The "slave" role means the device sits on the bus as a node that processes the EtherCAT datagram on the fly as it traverses each port, in contrast to an EtherCAT master which orchestrates the network. The AX58100LT integrates two 100BASE-TX Fast Ethernet PHYs directly on-die, eliminating the need for external PHY chips and reducing BOM cost, PCB area, and signal-integrity complexity for servo drives, distributed I/O, and sensor modules. With 100 Mbit/s full-duplex ports, it supports standard EtherCAT cycle times down to the 12.5 us micro-period range and the typical 1 ms motion-bus update rate. The industrial-grade -40C to +105C operating range suits it for servo, motion control, and factory automation deployments. Typical applications include EtherCAT servo motor drives, decentralized digital I/O modules, EtherCAT sensor interfaces, robotic joint controllers, EtherCAT junction or branch modules, and other industrial-automation nodes. The STM32F303RE host reference design published by ST validates AX58100LT for FOC (field-oriented control) servo loops and points designers toward proven firmware stacks. When designing with the AX58100LT, ensure the 80-pin LQFP-EP exposed pad is soldered with sufficient thermal via arrays to dissipate internal PHY power, and route the differential MDI pairs as 100-ohm differential controlled-impedance traces. The host MCU should run an ASIX-supported EtherCAT slave stack (e.g., SOES or SSC ported to the chosen MCU) to maximize bus conformance. This page synthesizes distributor pricing, LQFP-80 drop-in alternatives, and practical industrial-board design notes not found in the raw manufacturer datasheet, giving the BOM engineer a complete procurement and design entry point for EtherCAT nodes built around the AX58100LT.
B50280C1KFBG - Octal 10/100/1000 PHY Transceiver | Broadcom
The Broadcom B50280C1KFBG is an octal 10/100/1000 Mbps Ethernet PHY transceiver integrated circuit designed for high-density networking line cards and switch aggregation. The device integrates eight independent Gigabit Ethernet physical layer transceivers in a single package, supporting full-duplex operation over twisted-pair copper media, and is targeted at enterprise switching platforms where port density and per-port power are both critical design constraints. An Ethernet PHY (Physical Layer Device) is the lowest-speed layer of the OSI networking stack, handling the analog signaling, encoding/decoding, clock recovery, and link training required to push bits over a Cat5e/Cat6 cable. PHY transceivers sit beneath the MAC and switch fabric; an octal PHY like the B50280C1KFBG aggregates eight Gigabit PHYs into one IC to simplify PCB routing, reduce component count, and minimize board area compared to using eight discrete single-port PHYs. PHY -> Ethernet transceiver -> Networking IC -> Interface IC -> Integrated Circuit is the broader hypernym chain. The B50280C1KFBG supports auto-negotiation, auto-MDI/MDIX crossover, Energy Efficient Ethernet (EEE, IEEE 802.3az), and 802.1AE MACsec readiness depending on firmware build. Each port independently negotiates 10/100/1000BASE-T, recovers clock and data, and presents GMII/RGMII to the host MAC. The integrated DSP-based echo canceller and baseline wander correction enable robust 100m Cat5e link performance without external magnetics beyond the standard 1:1 transformer. Typical applications include top-of-rack and leaf switches, network interface cards with multi-port PHYs, router line cards, industrial Ethernet switches, and telecom access equipment. Per-port power below ~1W and the octal integration make it especially suited for chassis switches where hundreds of Gigabit ports must be supported within thermal and power budgets. Designers should pay attention to the SGMII/SerDes reference clock architecture, the quad-port group power sequencing, and the requirement for dedicated 1:1 isolation transformers per port. PCB layout for the B50280C1KFBG demands careful 100-ohm differential pair routing for each of the eight MDI channels with strict length matching. This page synthesizes distributor pricing, package specifications, and drop-in alternatives that are not found in the manufacturer datasheet alone, providing a single reference for engineers evaluating the B50280C1KFBG against multi-port PHY options from Broadcom and competitor families.
BCM47083SL01 - Single-Band 11n WLAN SoC | Broadcom
Broadcom BCM47083SL01 is a single-band IEEE 802.11n WLAN system-on-chip (SoC) chipset offered in the BCM47083 family for embedded wireless networking equipment. The verified distributor information identifies it as an RF System on a Chip and confirms the 802.11n, single-band WLAN function. The available records identify Broadcom as the manufacturer and Broadcom Avago as the legacy distributor brand designation. A manufacturer datasheet URL, package dimensions, pin count, pinout, operating-frequency range, and detailed electrical ratings are not included in the supplied source data. An RF system-on-chip is an integrated semiconductor that combines wireless radio, baseband processing, and supporting control functions into one device. Within the product hierarchy, it is a WLAN connectivity SoC, a type of wireless network interface integrated circuit, and therefore belongs to the broader semiconductor and integrated-circuit categories. Integration can reduce the component count and board area required for an embedded 802.11n access point, router, gateway, or other connected product compared with a discrete radio approach. The principal verified feature of BCM47083SL01 is single-band IEEE 802.11n operation. This makes it relevant to embedded systems requiring Wi-Fi connectivity without a dual-band radio requirement. The device is listed by Mouser as an RF System on a Chip and WLAN chipset, while the DigiKey and Octopart records identify it as a Broadcom microprocessor-class component. Current distributor availability information compares listings from four distributors, with individual vendors such as Hotenda and Bettlink indicating stock. Because the supplied data does not contain a Broadcom datasheet, detailed RF characteristics cannot be stated safely. Information such as operating frequency, transmit power, receiver sensitivity, supported antenna interfaces, processor architecture, memory configuration, supply voltage, package type, and operating-temperature range requires the missing manufacturer document. The MPN suffix may encode ordering, temperature, or packaging information, but it must not be decoded without an authoritative part-number guide. Consequently, this page does not infer those parameters from the suffix. Typical implementation areas include embedded Wi-Fi routers, wireless gateways, access points, home automation controllers, industrial gateways, and connected consumer equipment. In these systems, the BCM47083SL01 can serve as the central WLAN connectivity component while an Ethernet controller or physical-layer transceiver handles wired networking. Site-listed LAN8720A-CP and DP83822HRHBR parts are examples of Ethernet-interface components that may appear in a broader connected product, although their use with BCM47083SL01 is not verified by the supplied Broadcom documentation. Design review should begin with the official Broadcom datasheet and package drawing. Pin assignment, exposed-pad requirements, RF routing, antenna matching, power sequencing, decoupling, PCB stack-up, and thermal management must be checked against the exact ordering variant. Do not reuse an existing footprint solely from distributor metadata; confirm the physical package and exposed thermal pad before schematic capture or PCB release. This page combines verified distributor descriptions, current sourcing links, specification gaps, engineering-use analysis, and design cautions in one decision-oriented record. It distinguishes confirmed facts from unavailable manufacturer parameters so engineers can identify what must be checked before qualifying BCM47083SL01 in a production wireless design.
BCM5221A3KPTG - 10/100 Ethernet PHY | Broadcom | Industrial
The Broadcom BCM5221A3KPTG is a single-port 10/100 Ethernet physical-layer transceiver, or PHY, built in monolithic CMOS technology and supplied in a 48-pin QFN package. It integrates a digital adaptive equalizer, analog-to-digital converter, phase-locked loop, line driver, encoder, decoder, and supporting circuitry. The device complies with IEEE 802.3u and supports the Media Independent Interface plus Auto-Negotiation. An Ethernet PHY is the physical-layer component in an Ethernet communications system. It converts digital MAC data through an MII or RMII connection into a differential analog signal suitable for twisted-pair cabling. Within the network hierarchy, the BCM5221 belongs to the Ethernet transceiver and interface-controller family, operating below the MAC and network protocol layers. Its integrated signal-conditioning blocks compensate for attenuation and distortion encountered on copper cables. The BCM5221A3KPTG combines multiple transmit and receive functions in one device. Its digital adaptive equalizer supports reliable reception on impaired copper links, while the integrated ADC converts received analog signaling into digital form. The PLL provides frequency-related support for the physical interface, and the line driver, encoder, and decoder implement the required transmit and receive paths. IEEE 802.3u compliance provides a defined basis for 10/100BASE-T operation. The MII interface exposes the controller-to-PHY functions needed by an Ethernet MAC, while Auto-Negotiation allows the PHY to negotiate supported operating modes with a linked partner. These functions make the device suitable for embedded Ethernet equipment that requires a dedicated PHY rather than a combined MAC-and-PHY controller. The monolithic CMOS integration reduces the number of external signal-conditioning components required for a basic copper Ethernet interface. Typical uses include industrial Ethernet controllers, embedded network adapters, printer and scanner interfaces, IP terminals, test equipment, and communication appliances. BCM5221A3KPTG can also support small embedded systems that need a 10/100 Ethernet physical layer while retaining a separate network controller. Developers should confirm the selected MII operating mode, external clock requirements, magnetics interface, and board-level timing against the Broadcom datasheet. For a robust implementation, provide the required decoupling capacitors at the supply pins, route the differential cable-side and digital interfaces according to the datasheet reference layout, and use a qualified Ethernet magnetic module. Maintain controlled impedance for the differential pairs, minimize stub lengths, and keep analog, digital, and high-current return paths separated. These measures reduce radiated emissions, susceptibility to cable transients, and bit-error risk. This product page organizes the BCM5221A3KPTG specifications, same-family alternatives, interface roles, application guidance, and design considerations into one engineering reference. It also distinguishes confirmed device functions from parameters that require confirmation against the manufacturer datasheet, helping engineers plan sourcing and hardware validation efficiently.
BCM5221A4IMLG - Single-Port RMII Ethernet PHY | Broadcom
Broadcom BCM5221A4IMLG is a single-port Ethernet physical-layer transceiver with an RMII interface, supplied with the MLG package code. It is intended for systems that require an Ethernet PHY connection to a digital controller or processor. The part belongs to the Interface ICs category and operates as part of the physical layer in an Ethernet communication chain, where it interfaces network media signals with a digital MAC-side bus. An Ethernet PHY is an interface integrated circuit that converts between physical network signals and digital data. It is a member of the broader Ethernet interface hierarchy, which includes controllers, transceivers, magnetics, connectors, and network processors. RMII is the Reduced Media Independent Interface used to connect the PHY to a digital Ethernet controller. This separation allows the PHY to handle the physical network layer while the controller manages higher-level frame processing and traffic control. The BCM5221A4IMLG is identified as a single-PHY RMII Ethernet device. Its ordering code, BCM5221A4IMLG, retains the broader BCM5221 family designation while distinguishing the A4I variant and MLG package identifier. This makes the exact suffix important during procurement and PCB design. The manufacturer’s BCM5221 product brief is the primary document for confirming the final electrical limits, temperature range, media interfaces, register behavior, and recommended application circuit before production release. As a single-port Ethernet transceiver, the device is suitable for embedded equipment, industrial controllers, set-top equipment, printers, network appliances, and other embedded platforms that use an RMII-connected Ethernet controller. A typical implementation places the BCM5221A4IMLG between the controller and the network magnetics or line-driver interface, while a 10/100 Ethernet magnetics component connects the PHY to the physical cable path. RMII reduces the number of parallel data lines relative to older MII arrangements, making it useful where board routing and connector density are important. The exact Ethernet speed support, internal and external crystal requirements, supply voltages, bias-resistor configuration, register map, and thermal limits must be taken from the BCM5221 product brief because those values are not identified by the distributor title alone. Engineers should also confirm the relationship between RMII clocking, PHY reset timing, strap resistors, and the selected network magnetics. Those details determine whether the controller interface operates reliably at power-up. A practical design priority is to preserve the manufacturer’s recommended power, decoupling, clock, and analog-network layout. RMII signals are digital, but the PHY still contains sensitive communication circuitry, so return paths, ground continuity, and isolation between digital and network-side return currents can affect signal integrity. Use the pin-description table and reference circuit in the BCM5221 product brief when assigning tracks and selecting external components. This page organizes the verified ordering information, interface classification, replacement candidate, application guidance, and design considerations into one engineering-focused reference. It also distinguishes the BCM5221A4IMLG from the closely related BCM5221A4KMLG ordering code, helping designers confirm package and suffix requirements without treating related family members as interchangeable without a complete review.
BCM5221A4KMLG - 10/100 Ethernet PHY, 48-QFN | Broadcom
Broadcom BCM5221A4KMLG is a single-port 10/100BASE-T Ethernet physical-layer transceiver with one driver and one receiver, operating from a 2.5 V to 3.3 V supply in a 48-pin QFN package. The PHY supports 10 Mbps and 100 Mbps links and is identified by the manufacturer as a low-power Fast Ethernet device with 175 mW power dissipation. An Ethernet PHY is the physical-layer component within the Ethernet hierarchy of network interface controller, transceiver, and communications semiconductor. It converts digital Ethernet data from a MAC into signals suitable for a twisted-pair or fiber interface and converts received signals back into digital data. The BCM5221 therefore occupies the boundary between a host controller and physical network medium, allowing embedded systems to connect directly to 10/100BASE-T networks. The device can be powered from either 2.5 V or 3.3 V and incorporates an integrated voltage regulator. Its 175 mW dissipation figure supports compact, power-conscious equipment designs. The -40°C to 85°C industrial temperature range also allows operation across commercial and industrial environments. An RMII-oriented product description and integrated regulator simplify implementation compared with a PHY requiring a larger external supply arrangement. The BCM5221 family combines a 10/100BASE-TX/FX-capable physical layer with low-power operation and intelligent power-down states. These states are useful in systems that must reduce energy use without losing the ability to resume network operation. Exact media-interface details, clocking requirements, magnetics recommendations, and exposed-pad thermal guidance should be implemented from the pin-description table and application information in the manufacturer datasheet 5221-DS07-405-RDS. Typical uses include industrial Ethernet controllers, embedded gateways, set-top equipment, printer electronics, automotive or transportation networking equipment, and compact communication modules. In an RMII design, the PHY connects to a network MAC or controller through its digital interface, while the analog side interfaces through magnetics to copper cabling. The 48-QFN footprint requires careful grounding and thermal design around its exposed pad. A key implementation consideration is that Ethernet PHY performance depends on the complete signal chain, including supply filtering, magnetics, cable routing, and reference-clock quality. Follow the reference schematic and component recommendations in the manufacturer datasheet rather than treating the PHY as a standalone Ethernet interface. Confirm that the selected RMII timing, cable, and magnetics arrangement satisfies the system link budget and electromagnetic-emissions requirements. This page combines the manufacturer datasheet, distributor product records, cross-reference findings, package information, application guidance, and drop-in replacement analysis for BCM5221A4KMLG. The comparison and design notes are intended to make footprint, voltage, interface, and sourcing decisions easier while keeping unresolved engineering details explicit.
BCM5221A4KPTG - 10/100 Ethernet Transceiver | Broadcom
Broadcom BCM5221A4KPTG is a single-channel 10/100BASE-TX and 100BASE-FX Ethernet transceiver with a 3.3 V supply, designed for industrial networking equipment and embedded Ethernet systems. The device supports MII and RMII host interfaces and is supplied in a 64-pin TQFP package. Its 10BASE-T and 100BASE-TX support provides a practical path for legacy copper links, while the 100BASE-FX capability supports fiber-based point-to-point links where longer reach or electrical isolation is required. An Ethernet PHY transceiver is an interface integrated circuit that converts digital Ethernet data into electrical or optical signaling for a network connection. In the hierarchy of networking electronics, the BCM5221 belongs to the Ethernet interface-controller and physical-layer transceiver class, where it sits between a host controller or processor and a 10/100BASE-TX copper medium or 100BASE-FX fiber medium. The BCM5221 provides one Ethernet transceiver channel, 10 Mbps and 100 Mbps data-rate support, 3.3 V operation, and an industrial temperature range of -40°C to 85°C. Its MII and RMII interfaces support different host-controller architectures: MII provides separate parallel control and data paths, while RMII uses a reduced pin interface intended to simplify connections with compatible Ethernet controllers. The 64-pin TQFP package also provides sufficient pin count for dedicated media, clock, control, and power connections. Broadcom positions the BCM5221 as a 10/100BASE-TX/FX mini-transceiver for copper and fiber connectivity. In a copper implementation, the PHY interfaces with magnetic components and an RJ45 network connector. In a fiber implementation, it interfaces with an external optical transceiver through its fiber-side signals. The host-side MII or RMII signals connect to an embedded processor, industrial controller, or dedicated Ethernet controller. Typical uses include industrial Ethernet gateways, embedded control systems, printer controllers, set-top equipment, factory automation equipment, and legacy 10/100 network upgrades. The part is particularly relevant when an existing design supports 10 Mbps and 100 Mbps copper links but also requires a 100BASE-FX option. Product qualification should confirm all electrical, timing, and fiber-interface requirements for the target network. For a new PCB, follow the Broadcom BCM5221 data sheet for the exact reference circuit, decoupling, clock, magnetics, resistor, and layout implementation. Preserve the specified MII or RMII interface arrangement, provide clean 3.3 V power, and account for the package thermal limits when placing the transceiver next to a switching regulator or processor. This product page combines the manufacturer data sheet, device specifications, sourcing information, application guidance, and design considerations to support faster engineering evaluation. It also distinguishes documented functions from parameters that still require board-level confirmation, helping designers assess BCM5221A4KPTG for copper, fiber, industrial, and embedded Ethernet implementations.
BCM5221KPB - 10/100 Ethernet Transceiver | Broadcom
The Broadcom BCM5221KPB is a 10/100BASE-TX/FX mini-PHY Ethernet transceiver with integrated physical-layer signaling, a 64-terminal BGA package, and industrial-temperature positioning. It is designed for network interfaces that need copper or fiber connectivity, link-status control, low-power operation, and compact PCB integration. The verified distributor data identifies the part as a 1/1 Ethernet transceiver, while the Broadcom data sheet provides the authoritative technical details for electrical, mechanical, and software configuration requirements. What is an Ethernet transceiver? An Ethernet transceiver is an interface IC that converts digital data into physical network signals and converts received signals back into digital data. A 10/100BASE-TX/FX mini-PHY sits below the Ethernet MAC and handles the physical encoding, clocking, signal conditioning, and link-related functions required for 10 Mb/s and 100 Mb/s networks. It belongs to the interface-IC hierarchy: Ethernet interface transceiver, physical-layer device, network-interface IC, and semiconductor. The BCM5221KPB is identified in the supplied data as a Broadcom 10/100BASE-TX/FX mini-PHY transceiver. The verified source list includes an official Broadcom PDF and distributor listings from DigiKey, Mouser, Octopart, Win Source, and other suppliers. The package is identified by the Partstack result as a square 64-terminal BGA with a ball terminal form and industrial temperature grade. Exact pin assignments, electrical limits, media interfaces, clocking modes, and register details remain tied to the manufacturer data sheet. Typical uses include embedded Ethernet equipment, industrial controllers, network adapters, telecom access equipment, and systems requiring a compact copper/fiber physical-layer interface. In a copper link, the device connects the Ethernet MAC-side digital interface to the transformer-coupled 10/100BASE-TX network. In a fiber-oriented implementation, the FX capability can support the appropriate optical-module interface, subject to the detailed application requirements in the Broadcom data sheet. Its industrial-grade identification makes it more relevant to equipment operating outside consumer-only temperature ranges, although exact temperature limits must be taken from the manufacturer documentation. Designers should verify the package land pattern, ball assignments, decoupling requirements, media-side components, and supported operating modes directly against the Broadcom data sheet. PCB layout is especially important for high-speed physical-layer signals; controlled impedance, short return paths, uninterrupted reference planes, and careful isolation between transmit and receive paths can reduce signal-integrity risk. Do not infer pin compatibility or substitute parts from package similarity alone. This product page combines the verified source URLs, practical interface-transceiver context, and explicit data gaps. It does not invent missing electrical values, pricing, pin names, or alternative cross-references that were not present in the supplied evidence.
BCM5222KPF - Dual-Port 10/100BASE-TX Ethernet PHY | Broadcom
Broadcom BCM5222KPF is a highly integrated dual-port 10/100BASE-TX Ethernet transceiver with digital adaptive equalization, ADC, phase-lock loop, line driver, encoder, decoder, and required support circuitry in a monolithic CMOS device. It supports IEEE 802.3u Fast Ethernet operation, including the Media Independent Interface (MII) and Auto-Negotiation functions, and is supplied in a 100-ball FBGA package. An Ethernet PHY, also called a physical-layer transceiver, is the interface between a digital network controller and copper Ethernet cabling. It converts transmitted digital symbols into analog signaling, receives and equalizes incoming analog signals, and converts them back into digital data. The BCM5222KPF places two Fast Ethernet physical-layer channels and their common support functions into one device, reducing external component count in dual-port network equipment. According to the manufacturer datasheet, BCM5222 integrates an adaptive equalizer, ADC, PLL, line driver, encoder, decoder, and support circuitry. The device is designed for dual-port 10/100BASE-TX networks and includes MII and Auto-Negotiation support. The verified distributor data identifies an industrial temperature grade, ball terminal form, square package shape, FBGA package code, and 100 terminals. Detailed electrical limits, pin assignments, clock requirements, and register behavior must be confirmed in the manufacturer datasheet before design release. The BCM5222 family is suited to Ethernet switches, routers, network interface cards, embedded gateways, industrial controllers, and other systems requiring two copper Fast Ethernet ports. Its integrated CMOS implementation can simplify board layout compared with a discrete transceiver approach, although careful separation of analog and digital circuits remains essential. MII compatibility allows connection to a compatible Ethernet MAC, while Auto-Negotiation supports speed and duplex negotiation according to the system configuration. A practical design must preserve the transceiver's required decoupling, controlled clocking, MII signal integrity, and high-speed differential routing. The 100-ball FBGA package requires careful escape routing and via-in-pad or via-near-pad strategy on multilayer PCBs. Because the supplied data does not include verified pin names or detailed timing, power, and environmental limits, engineers should use the official BCM5222 data sheet for the complete schematic, layout, and component-selection checklist. This product page combines the official Broadcom datasheet reference, distributor package data, and practical Ethernet-PCB guidance. It does not infer undocumented alternatives or specifications. Review the source links and manufacturer documentation for procurement, lifecycle, and design qualification requirements.
BCM5222KQMG - Dual-Port 10/100 Ethernet PHY | Broadcom
The Broadcom BCM5222KQMG is a dual-port, full-duplex Ethernet physical-layer transceiver supporting 10 Mbps and 100 Mbps operation in a 100-lead MQFP package measuring 14 x 20 mm. The device belongs to the Ethernet PHY hierarchy, where a PHY connects a digital media-access controller to a copper Ethernet network through an MII interface. An Ethernet PHY is the physical-layer portion of an Ethernet communication system. It converts digital data into signals suitable for transmission over twisted-pair cabling and recovers timing and data from received signals. According to the Broadcom BCM5222 data sheet, the BCM5222 integrates a digital adaptive equalizer, analog-to-digital converter, phase-locked loop, line driver, encoder, decoder, and supporting circuitry in one monolithic CMOS device. It complies with the IEEE 802.3u requirements for Fast Ethernet, including the Media Independent Interface and Auto-Negotiation sections. The verified distributor listing identifies BCM5222KQMG as a 2/2 full-Ethernet transceiver with PHY functionality and a 100-MQFP package. A separate indexed specification describes the BCM5222 family as a dual-port 10/100BASE-TX Fast Ethernet transceiver. These facts make the part applicable to dual-port embedded networking equipment, but the supplied data does not state the exact PHY-versus-MAC division for every internal function, nor does it provide a complete electrical performance table for this orderable MPN. Its monolithic integration is significant because it consolidates several receive and transmit signal-chain blocks into one component. The integrated adaptive equalizer supports copper-channel signal conditioning, while the phase-locked loop, converter, line driver, encoder, and decoder form the core transmit and receive implementation described by Broadcom. The supported MII and Auto-Negotiation functions help connect the PHY to an Ethernet MAC through a conventional parallel interface. Typical application candidates include industrial Ethernet controllers, embedded network appliances, printer and scanner interfaces, network interface cards, and dual-port embedded communication systems. Because the verified excerpts do not provide supply voltage, operating temperature, media reach, cable length, jitter, latency, EMI performance, or exact register compatibility, these specifications must be checked in the manufacturer data sheet before schematic sign-off. A practical design decision is to preserve the 100-MQFP footprint and verify the exact MII pin assignments before routing. Designers should also check the Broadcom reference design or application guidance for recommended magnetics, termination, crystal or clock requirements, decoupling, and controlled-impedance layout. Those implementation details cannot be inferred solely from the distributor classification. This page separates verified BCM5222KQMG facts from unavailable orderable-part details and synthesizes sourcing, comparison, and design considerations for engineers. It does not substitute generic Ethernet-PHY claims for missing manufacturer data, helping procurement and hardware teams distinguish confirmed specifications from parameters that still require verification.
BCM5241A1KMLG - 10/100 Ethernet PHY | Broadcom Limited
Broadcom Limited BCM5241A1KMLG is a single-port Ethernet physical-layer transceiver supporting 10BASE-T, 100BASE-TX, and 100BASE-EFX operation. It integrates one Ethernet driver and one receiver, supports 2.5 V and 3.3 V supply rails, and is identified as a 10/100 Base-TX MII PHY transceiver. The device is intended for embedded networking products that connect a digital network controller or processor to an Ethernet magnetics interface. An Ethernet PHY is the physical-layer component in an Ethernet communications system. It converts digital data from a MAC or network processor into signals suitable for a twisted-pair cable and reconstructs incoming signals for the digital controller. In the network hierarchy, a PHY is a network interface IC and a semiconductor device within the broader category of Ethernet interface integrated circuits. The BCM5241 supports both 10 Mb/s and 100 Mb/s copper links for legacy Fast Ethernet equipment. The BCM5241A1KMLG provides one transmit driver and one receive channel for a single-port design. Its identified 2.5 V and 3.3 V operating options allow implementation with either a 2.5 V core-side supply or a 3.3 V interface-side supply where the surrounding circuitry permits it. Its listed 170 mW power figure is relevant to compact embedded systems, although the actual board-level consumption depends on operating mode, network activity, supply voltage, and the external circuit configuration. Broadcom identifies BCM5241A1KMLG as an active MII PHY transceiver. MII, or Media Independent Interface, separates the PHY from the digital MAC through standardized control, data, and status signals. This division of responsibility allows the same physical-layer circuit to support multiple Ethernet MAC implementations. The device also supports 100BASE-EFX, extending its application scope beyond the conventional 10BASE-T and 100BASE-TX copper modes listed for the part. Typical uses include industrial Ethernet controllers, embedded routers, print servers, set-top equipment, network interface adapters, and other equipment requiring a single copper Ethernet port. The part is particularly relevant where a 10/100 Mb/s connection is sufficient and board area, component count, and interface simplicity matter more than support for gigabit data rates. PCB design should preserve the separation between digital circuitry, analog PHY signals, and the Ethernet transformer network. Keep the PHY supply bypass capacitors close to their power pins, route high-speed differential and analog signals over continuous ground planes, and follow the manufacturer pin-description table and recommended application layout when assigning tracks and test points. This page organizes the Broadcom BCM5241 product information, verified distributor records, lifecycle status, interface characteristics, application guidance, and same-family replacement information into an engineering-focused reference for evaluating the BCM5241A1KMLG in a new Ethernet design.