بەرهەمەکان (28)

TLE62512GXUMA3 - 1 MBd HS-CAN Transceiver, ISO 11898-5 | Infineon
TLE62512GXUMA3

TLE62512GXUMA3 - 1 MBd HS-CAN Transceiver, ISO 11898-5 | Infineon

The Infineon TLE62512GXUMA3 is a high-speed CAN transceiver for automotive and industrial networks, delivering data transmission rates to 1 MBd in a 14-pin PG-DSO-14 surface-mount package. It complies with the ISO 11898-5 standard, operates from a 4.75 V to 5.25 V supply, and adds a separate VIO input so the logic side can run at a lower microcontroller supply voltage. A CAN transceiver, also called a CAN physical-layer interface or CAN PHY, is the bridge between a microcontroller's CAN controller and a differential CAN bus. It converts logic-level TXD and RXD signals into the differential CANH and CANL bus pair and converts received bus levels back to digital logic. The Infineon TLE6251-2G family belongs to the high-speed CAN (HS-CAN) class of interface ICs, sitting at the physical layer of an automotive communication network. Key features of the TLE62512GXUMA3 include very low power consumption in Sleep mode, bus wake-up capability, a local wake-up inhibit output to control external circuitry, and split termination to stabilize the recessive bus level. A separate failure diagnosis output gives the host microcontroller a hardware health check on the physical layer, and the device is optimized for low electromagnetic interference, which reduces the need for external shielding and filtering in the ECU. Technically, the TLE6251-2G is positioned as the successor of the TLE6251G, with excellent passive behaviour in power down. This makes the part well suited to mixed power-supply HS-CAN networks where some nodes are unpowered at times while the bus remains active. The TLE6251G and the TLE6251-2G are pin compatible and function compatible, so the two devices can be used interchangeably on the same PCB land pattern. The separate VIO pin allows the transceiver to be interfaced to microcontrollers supplied from 3.3 V or 5 V without level-shifting logic. Typical applications include electronic control units in body and powertrain domains, CAN gateways, climate control and comfort modules, sensor nodes in distributed vehicle networks, industrial CANopen and DeviceNet equipment, and diagnostic interfaces in workshop tooling. When laying out the board, place the 100 nF and 1 uF supply decoupling capacitors directly at the VCC and VIO pins, and keep the CANH and CANL traces short, impedance-matched, and free of stubs. Use the split termination feature instead of fitting a single 60 ohm resistor so that split values can be tuned for EMC margin. This page consolidates device specifications, drop-in alternatives from the same Infineon family, a parameter comparison, and practical layout guidance into a single engineering reference.

RFQ پەیوەندی
TLE8457DSJXUMA1 - LIN Transceiver + 3.3V LDO | Infineon
TLE8457DSJXUMA1

TLE8457DSJXUMA1 - LIN Transceiver + 3.3V LDO | Infineon

The Infineon TLE8457DSJXUMA1 is a monolithic LIN transceiver with an integrated 3.3 V low-dropout voltage regulator, supplied in an 8-pin PG-DSO-8 (TSON-8) surface-mount package. It is a 1/1 LIN transceiver supporting LIN specification 2.2A and SAE J2602, with a maximum data rate of 20 kbps and an integrated LDO capable of sourcing up to 70 mA at 3.3 V for a host microcontroller and its sensors. A LIN (Local Interconnect Network) transceiver is a physical-layer interface IC that bridges a low-speed microcontroller UART to a single-wire automotive bus. The LIN bus is standardized in ISO 17987 and widely used for body-electronics sub-networks (door modules, mirror adjusters, seat controllers, HVAC flaps) where CAN is too expensive. The integrated LDO allows a TLE8457DSJ slave node to be powered directly from the 12 V automotive battery without a separate voltage regulator, simplifying PCB design. Key features of the TLE8457DSJXUMA1 include an ultra-low standby current of 20 µA (suitable for permanent-battery-attach nodes), battery input voltage range of 5.5 V to 28 V with transient tolerance per ISO 7637, integrated VCC undervoltage reset with fixed 3.3 V output, integrated current limit, thermal shutdown, and bus-pin ESD protection up to ±8 kV (HBM). The device operates across the automotive -40 °C to +150 °C junction temperature range and is qualified to AEC-Q100 grade 1, making it suitable for under-hood and body-control modules. The TLE8457DSJ uses a bi-directional bus driver architecture compliant with LIN 2.2A and SAE J2602, with internal slope control to meet EMC requirements per IEC 61967 and SAE J1752. The integrated LDO is a p-channel MOSFET LDO architecture for low quiescent current, with internal compensation and soft-start. The part is offered as 'DSJ' (PG-DSO-8) only — the XUMA1 suffix denotes a 2,500-piece reel per IEC 60286-3. Typical applications include LIN slave nodes in door modules, seat-control modules, HVAC damper actuators, interior lighting, rain/light sensors, and other LIN sub-nodes in automotive body-electronics networks. The integrated 3.3 V/70 mA supply removes the need for an external regulator at each LIN slave, reducing BOM count and PCB area. When designing with the TLE8457DSJXUMA1, ensure the LIN bus pull-up is correctly selected (the device provides the slave-side pull-up internally only in some modes — see the datasheet). Place the VBAT decoupling capacitor (typically 100 nF ceramic + bulk) close to the VBAT pin to meet ISO 7637-2 transient immunity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the TLE8457DSJXUMA1 not found in the manufacturer datasheet alone.

RFQ پەیوەندی
TRS3232EIRGT - Dual RS-232 Transceiver, ±15kV ESD | TI
TRS3232EIRGT

TRS3232EIRGT - Dual RS-232 Transceiver, ±15kV ESD | TI

The Texas Instruments TRS3232EIRGT is a 3V to 5.5V dual-channel RS-232 line driver and receiver (transceiver) with ±15kV IEC ESD protection on the serial-port pins, delivering 250 kbps data rates in a compact 16-pin VQFN (RGT) 3x3 mm package. An RS-232 line driver/receiver is an interface IC that converts logic-level UART signals (TTL/CMOS, typically 0V to 3.3V or 5V) into the voltage-swing-compliant RS-232 levels required by serial-port connectors, and vice versa. It sits within the interface IC hierarchy of transceivers, alongside CAN, RS-485, and LVDS transceivers, and forms the electrical bridge between an asynchronous communication controller and the physical serial connector. Key features include two drivers and two receivers for full-duplex communication, a dual charge-pump circuit that generates RS-232 compliant voltage swings from a single 3V to 5.5V supply with only four small 0.1uF external capacitors, ±15kV IEC ESD protection pin to pin (including GND), and conformance to TIA/EIA-232-F. The 250 kbps data rate comfortably covers standard UART baud rates up to 250 kbaud. Technically, the device integrates an efficient regulated charge-pump inverter and doubler, so the driver outputs swing to the RS-232 defined levels even at a 3.3V supply. Receiver inputs tolerate up to ±30V, providing robustness against fault conditions. ESD structures rated to ±15kV (HBM and IEC air-gap) protect bus pins against electrostatic discharge events in field environments. Typical applications include industrial PLC and factory-automation serial links, point-of-sale terminals and barcode scanners, and legacy/debug UART ports on networking and embedded processor boards. The small VQFN-16 footprint suits space-constrained designs where an SOIC-16 is too large. Design consideration: ensure the four charge-pump flying capacitors and both supply bypass capacitors (0.1uF) are placed as close to the pins as possible; exceeding the 5.5V supply or omitting capacitors degrades signal swing and ESD robustness. This page synthesizes distributor pricing, package/pinout detail, drop-in alternative guidance, and practical design notes beyond what the manufacturer datasheet provides, with pricing as of 2026-10-20.

RFQ پەیوەندی
TUSB1106RGTR - 12Mbps USB 2.0 Transceiver | Texas Instruments
TUSB1106RGTR

TUSB1106RGTR - 12Mbps USB 2.0 Transceiver | Texas Instruments

The Texas Instruments TUSB1106RGTR is a single-channel USB 2.0 transceiver supporting low-speed 1.5 Mbit/s and full-speed 12 Mbit/s operation, packaged in a 16-pin VQFN (RGT) module with an exposed pad. The device provides transmit and receive paths for one USB link and operates from a 3 V supply according to comparison data published for this family. A universal serial bus transceiver is an interface IC that bridges a host or peripheral controller with a USB connector. USB transceivers sit between the digital controller and the physical D+ and D- conductors, handling differential signaling, logic thresholds, and bus-direction control. Within the product hierarchy, the TUSB1106 belongs to the universal serial bus controller family and then to the broader interface IC and semiconductor categories. The TUSB1106 is compliant with the Universal Serial Bus Specification Revision 2.0 and supports both 1.5 Mbit/s low-speed and 12 Mbit/s full-speed data rates. Its single transmit-and-receive arrangement is intended for designs with one USB port rather than devices requiring multiple integrated USB PHY channels. A compact 3 x 3 mm VQFN footprint also supports compact peripheral and accessory designs where board area is constrained. The exposed thermal pad provides a low-inductance connection between the device and the supply and ground planes when the package is soldered according to the manufacturer land pattern. Because the exposed pad is an electrical connection rather than an isolated pad, the PCB must implement the complete footprint, including thermal-via and copper-thermal-pad features defined in the TUSB1106 documentation. Typical applications include USB-to-serial adapters, external storage bridges, portable data-collection equipment, industrial control peripherals, and USB connectivity in accessory boards. The TUSB1106 is especially useful when a controller provides only a parallel or multiplexed USB interface and the system requires a dedicated USB 2.0 transceiver with both transmit and receive capability. Layout is the primary design consideration for this device. Route the differential D+ and D- connections as a controlled-impedance pair, minimize stub branches, and place the required decoupling capacitors close to their designated pins. Confirm the pin arrangement, exposed-pad connection, and capacitor placement directly against the TUSB1106 datasheet before releasing the PCB artwork. This page consolidates the verified USB 2.0 data rates, package information, application context, and drop-in comparison options with practical PCB guidance. It is intended to accelerate component selection while keeping unsupported electrical details out of the published specification set.

RFQ پەیوەندی