Logic ICs
بەرهەمەکان (720+)
CD4050BCM - 6-Channel 3-18V CMOS Buffer | onsemi
The onsemi CD4050BCM is a six-channel, non-inverting CMOS buffer operating from 3 V to 18 V, packaged in a 16-pin SOIC. It provides six independent 1-bit buffers with push-pull outputs, preserving the logic level at each input while providing a buffered drive path. Its monolithic complementary-MOS construction uses N-channel and P-channel enhancement-mode transistors, and its single-supply operation supports logic-level conversion without separate input and output supply rails. A CMOS logic buffer is a digital semiconductor that reproduces the logical state of its input at its output while adding drive strength and isolation. The CD4050 series belongs to the CD4000 CMOS logic family, whose low-power operation and high noise immunity make it suitable for industrial control, interface conditioning, and systems that combine low-voltage control signals with moderate-load logic. Unlike an open-collector buffer, this device uses a push-pull output configuration for faster transitions and more predictable behavior at low output impedance. The principal device characteristics are a 3 V to 18 V supply range, six non-inverting channels, one logic bit per element, push-pull outputs, and a 16-pin SOIC package. According to the manufacturer information, the CD4050 family is designed for logic-level conversion using a single VDD supply. This makes it useful when a signal source and the receiving logic operate from the same supply rail but still benefit from a separate buffered output stage. The three-state CD4053B appears in a comparison listing as a superficially similar alternative, but its three-state outputs and additional control function make it functionally different from the always-enabled CD4050BCM. A CD4000-series cross-reference is more useful for identifying functional equivalents than for guaranteeing package compatibility. Engineers should still verify the exact suffix, package drawing, supply limits, input levels, propagation delay, output-current capability, and temperature grade before approving a substitute. Typical applications include buffering control signals in industrial automation equipment, conditioning sensor and interface signals, supporting multiple logic rails in embedded systems, and driving compatible CMOS inputs in test and measurement equipment. Because the CD4050BCM provides independent buffers, designers can use each channel separately rather than combining inputs electrically. The principal PCB consideration is to place the device close to the protected logic inputs and route each output to the intended load with minimal trace length. Decoupling requirements, unused-channel handling, input rise and fall times, and output drive limits should be taken from the manufacturer datasheet. This page combines device identification, sourcing guidance, verified alternatives, comparison criteria, and practical design considerations to support an engineering replacement decision.
CD4050BCN - Hex Non-Inverting CMOS Buffer | onsemi
The onsemi CD4050BCN is a six-element, non-inverting CMOS buffer with one-bit push-pull outputs, supplied in a 16-pin PDIP package. The device uses six N-channel and six P-channel enhancement-mode MOSFETs, providing buffered non-inverting signal paths from a single power supply. Its six independent channels make it useful wherever multiple digital signals require buffering, isolation from fan-out loading, or restoration of logic levels. A CMOS logic buffer is a digital integrated circuit that reproduces its input signal at an output while providing gain and reducing the loading imposed on the driving circuit. The CD4050BC belongs to the CD4000 CMOS logic family, placing it in the hierarchy of CMOS logic, logic IC, and digital semiconductor. Unlike an open-collector buffer, its specified push-pull output uses both pull-up and pull-down output stages to produce a defined low or high voltage. The principal features of the CD4050BCN are its six parallel non-inverting channels, one-bit signal handling, push-pull output stage, and single-supply operation. Each channel preserves the logical polarity of its input, allowing a buffer to be inserted without changing Boolean logic. The monolithic CMOS construction supports low quiescent power in many logic applications and combines high input impedance with a low-impedance output capable of driving subsequent digital stages. Technical operation is based on complementary N-channel and P-channel enhancement-mode transistors. The two transistor types combine to create the input stage, output drive, and internal logic functions. Because the outputs are push-pull, a low output is actively pulled toward ground while a high output is actively pulled toward the positive supply. This architecture is appropriate for conventional CMOS logic rails and for interfaces where a buffered output must present a more defined drive condition to the next stage. Typical uses include buffering control and status signals in digital systems, supporting multiple CMOS logic inputs, driving standard 4000-series logic, and isolating a sensitive digital source from downstream capacitance. The six-channel organization can also simplify designs that previously required multiple discrete buffers. Each buffered path retains non-inverting behavior, which is important when the original logic equation must remain unchanged. Designers should verify the operating voltage, input and output timing limits, absolute maximum ratings, and temperature range against the manufacturer datasheet before using the device at a system rail. Decoupling should follow the manufacturer recommendation, and unused inputs must not be left floating. The 16-pin PDIP package is intended for through-hole PCB assembly rather than a surface-mount production flow. This page organizes the CD4050BCN function, package information, verified alternatives, and practical selection considerations in one engineering-focused reference. It also distinguishes confirmed drop-in candidates from alternatives that use a different package, helping designers avoid replacement parts that require board changes.
CD4050BD - Hex Non-Inverting CMOS Buffer, 3-18V, 16-SOIC | Texas Instruments
The Texas Instruments CD4050BD is a hex non-inverting buffer (buffer/converter) in a 16-pin SOIC package, providing six independent push-pull CMOS output stages that operate from a single 3 V to 18 V supply. What is a hex non-inverting buffer? A buffer is a logic IC that reproduces the logic level of its input at its output without inversion, adding gain and drive strength rather than changing the boolean function. The CD4050 belongs to the RCA CD4000 CMOS logic family, whose defining characteristic is wide supply-voltage tolerance from 3 V up to 18 V, allowing one device to interface 3.3 V, 5 V, 9 V and 15 V CMOS domains. Within the logic hierarchy, CD4050 is a buffer/converter (line driver) rather than a gate, and the six-element arrangement makes it a hex part. Key features include six non-inverting channels, push-pull output stages that source and sink current symmetrically, and single-supply operation that also permits input levels above VCC for level conversion. Because the outputs are push-pull rather than open-drain, no external pull-up resistors are required and the part drives capacitive bus loads directly. The 16-SOIC (0.154 inch, 3.90 mm width) surface-mount package is a legacy-standard footprint still widely supported by assembly houses and compatible with automated pick-and-place lines. Technically the part uses complementary CMOS (CMOS) construction, giving high noise immunity and low static power consumption across the supply range. Because it is a converter-class device, input thresholds track the supply rails rather than being fixed to a single logic standard, which is the mechanism that makes single-supply level shifting possible. Its main limitation versus modern rail-to-rail buffers is speed: the CD4000-family propagation delay is on the order of tens of nanoseconds, far slower than CMOS logic buffers such as the 74HC04 class. Typical uses include buffering long TTL or CMOS bus lines, level translation between 3.3 V, 5 V and higher-voltage CMOS domains, driving heavier loads than a plain gate can handle, and isolating control signals in industrial, instrumentation and legacy 4000-series designs where mixed-voltage CMOS logic still appears. A key design consideration is that CD4000-family parts draw supply current that rises with switching frequency, so the supply rail must be able to absorb dynamic current while maintaining a stable ground reference; a 0.1 uF bypass capacitor close to pin 14 is standard practice. Because this is a mature, cost-optimized part, designers migrating to 74HC/74HCT logic should re-check timing margins and input-level compatibility rather than assuming interchangeability. This page consolidates distributor pricing, same-footprint drop-in alternatives and practical layout guidance that are not collected in any single manufacturer document, giving engineers a single reference before committing to the CD4050BD on a new board.
CD4050BE - 6-Channel CMOS Buffer | Texas Instruments
The Texas Instruments CD4050BE is a six-element, non-inverting CMOS buffer and logic-level converter with one bit per element and push-pull outputs, packaged in a 16-pin PDIP. Its verified operating supply range is 3 V to 18 V, allowing the same device family to buffer or shift signals between different logic voltage domains using one supply voltage. A CMOS buffer is a digital logic device that reproduces its input signal at the output while providing buffering and, in this case, non-inverting logic-level conversion. Within the product hierarchy, the CD4050BE is a six-channel buffer, part of the CD4000 CMOS logic series and the broader logic IC category. Unlike an inverting buffer, each of its six channels preserves the input logic state. The six-channel architecture allows one package to serve several independent signal paths. Push-pull outputs provide a defined output state and make the device suitable for driving downstream CMOS inputs. Logic-level conversion can bridge signals whose voltage levels differ when the input and output thresholds remain compatible with the selected supply voltage. The CD4050B family uses a single positive supply, and the verified product information identifies a 3 V to 18 V operating range. This broad range supports integration across legacy 5 V systems and higher-voltage CMOS logic where the input and output signal levels are compatible with the device thresholds. Exact propagation delay, output-current, and input-threshold values were not included in the supplied verified data and therefore are not asserted here. Typical uses include interfacing signals between different logic-voltage domains, buffering multiple digital control lines, and driving CMOS inputs from sources operating at a different logic level. The device can also provide multiple non-inverting channels in logic circuits where inversion would be undesirable. Because each channel is independent, unused channels should be tied to a defined logic state according to the manufacturer recommendations. The main design consideration is ensuring that every connected signal remains within the input and output limits of the selected 3 V to 18 V supply. Designers should also account for unused inputs, supply decoupling, output loading, and the maximum transition rates verified in the manufacturer datasheet. The through-hole PDIP package is intended for conventional through-hole PCB assembly rather than surface-mount production. This page consolidates the verified manufacturer and distributor information for CD4050BE, adds same-package cross-reference options, and provides practical guidance for logic-level conversion, unused inputs, decoupling, and component selection. It also distinguishes confirmed characteristics from parameters that require consultation of the manufacturer datasheet before design release.
CD4050BF - 6-Channel CMOS Buffer, 3-18 V | Texas Instruments
The Texas Instruments CD4050BF is a 6-channel, non-inverting CMOS hex buffer and logic-level converter operating from 3 V to 18 V. The device is supplied in a 16-pin ceramic dual in-line package, and its specified temperature range is -55 °C to 125 °C. Each buffer provides a non-inverting output path, allowing the part to support buffering and single-supply level translation between compatible CMOS voltage domains. A CMOS hex buffer is a digital logic device that receives six input signals and presents six buffered, non-inverting outputs. Buffers separate a source from its load, improve signal integrity, and can isolate logic levels when the input and output use different voltage references within the device operating range. In the CD4000 family hierarchy, the CD4050BF belongs to CMOS logic ICs and is commonly used as a line driver or logic-level converter. The verified feature set includes six buffered channels, single-supply operation from 3 V to 18 V, non-inverting logic, and a military temperature range of -55 °C to 125 °C. Because it uses one supply voltage, the CD4050BF avoids the separate positive and negative reference rails historically associated with TTL-to-CMOS interface designs. This makes it useful where the source and destination circuits operate from the same supply but still benefit from output buffering. The CD4050BF is based on the CD4050B family architecture and is intended for digital buffering rather than analog amplification. Its CMOS inputs provide high input impedance and minimize loading of the upstream device. Each output stage restores logic levels, helping maintain usable rise and fall times when driving additional CMOS inputs or cable capacitance. Typical applications include industrial control and instrumentation, data acquisition, test equipment, legacy interface isolation, clock or signal distribution, and level translation within a 3 V to 18 V system. In instrumentation, the six channels can buffer sensor-conditioning outputs before they enter an ADC or counter. In control systems, the part can distribute buffered digital state signals among multiple receiver sections. When designing around the CD4050BF, keep every connected signal within the specified input and output voltage limits, and do not exceed the 18 V maximum supply voltage. Decoupling close to the supply pins remains necessary for a CMOS device switching capacitive loads. Because the verified data does not provide a complete electrical characteristic table, propagation delay, output drive current, input leakage current, and logic-level thresholds should be confirmed in the manufacturer datasheet before release. This page consolidates manufacturer and distributor references, validated CD4000-family equivalents, package-aware comparisons, and practical application guidance. It also identifies where the available sources do not publish a value, preventing unverified electrical specifications from being presented as guaranteed production data.
CD4050BK - 18V CMOS Hex Buffer | Harris Corporation
Harris Corporation CD4050BK is a non-inverting, six-element CMOS buffer and level converter with a maximum supply voltage of 18 V, packaged in a 16-CFP configuration. The device provides six independent one-bit channels and uses push-pull outputs according to the CD4050 family documentation. Its principal role is buffering compatible CMOS signals while supporting logic-level conversion with a single power supply. A CMOS buffer is a digital logic device that reproduces its input signal at an output with added drive strength. The CD4050 belongs to the CD4000 CMOS logic family, which sits within the broader digital IC and logic IC hierarchy. Unlike open-collector buffers, these devices use push-pull outputs, allowing them to source and sink output current without requiring an external pull-up resistor. The verified CD4050 family information identifies six non-inverting channels, one output bit per element, 3 V to 18 V operation, and an 18 V maximum supply rating. CMOS construction supports low static power relative to many older bipolar logic families. The buffered outputs are intended to improve signal integrity when driving downstream logic or interconnect, while the single-supply level-conversion capability can bridge compatible systems operating at different logic thresholds. The CD4050B family is based on complementary MOS circuitry using N-channel and P-channel enhancement-mode transistors. Separate input and output behavior should be checked against the relevant datasheet before finalizing edge-rate, fan-out, and loading calculations. The supplied source set confirms the CD4050B family's three-rail logic-level-conversion function and 3 V to 18 V supply range, but it does not provide a complete timing table, output-current rating, or absolute maximum ratings for the Harris CD4050BK. Typical uses include buffering digital control signals, interfacing compatible CMOS logic domains, clock distribution, and driving multiple standard CMOS loads. The non-inverting topology preserves signal polarity, while six independent channels make the device useful when more than one buffered logic path is required. Board-level applications should avoid using the CD4050BK for high-speed differential signals, high-voltage isolated interfaces, or loads exceeding the verified output-current capability. A key design consideration is that buffered CMOS outputs still have finite rise and fall times. Long PCB traces, capacitive inputs, stacked supply pins, and high fan-out can slow edges and create timing-margin risk. Decoupling capacitors should be placed close to the supply pins, while unused inputs must be connected to a defined logic level. Exact capacitor values, drive-current limits, and timing thresholds require the missing manufacturer data. This page consolidates the verified distributor identity, package description, CD4050B family supply range, logic function, cross-reference results, and practical design constraints. It also distinguishes verified facts from unavailable electrical details rather than estimating pinout, timing, thermal, or lifecycle values that are not present in the supplied sources.
CD4050BM - 6-Channel CMOS Buffer, 3-18V | Texas Instruments
The Texas Instruments CD4050BM is a six-channel CMOS buffer and level converter with three inverting channels and three non-inverting channels, operating from 3 V to 18 V in a 16-pin SOIC package. The device supports single-supply operation, push-pull outputs, and input signals whose high level may exceed VDD for CMOS-to-DTL or TTL level conversion. Its six-buffer organization makes it suitable for buffering digital control signals, translating voltage domains, driving multiple logic inputs, and isolating logic paths. A CMOS buffer is a digital interface circuit that reproduces a binary input at its output while providing electrical buffering and potentially translating a signal into the voltage range accepted by the receiving logic family. The CD4050BM belongs to the CD4000 CMOS logic family, which includes the broader categories of CMOS buffer, logic converter, logic IC, and semiconductor. Unlike a passive resistor divider, the active push-pull output can source and sink current more effectively while preserving a valid logic level. The principal benefit of the CD4050BM is its combination of six independent channels in one package. Three channels invert the input and three preserve polarity. A single VDD rail powers the device, and the input high threshold can operate independently of VDD. This arrangement is useful when a system must accommodate signals from a higher-voltage source or drive DTL and TTL-compatible loads without requiring a second supply rail. The Texas Instruments CD4050B family is specified for a 3 V to 18 V operating range. The manufacturer product page describes the devices as inverting and non-inverting hex buffers intended for logic-level conversion using only VCC. The precise propagation delay, output drive current, input leakage, temperature range, and package dimensions for the exact CD4050BM orderable were not included in the retrieved snippets, so those values remain marked as data needed rather than being inferred from another package or suffix. Typical applications include CMOS-to-DTL conversion, CMOS-to-TTL interfacing, digital signal buffering, control-signal isolation, and general-purpose logic-level translation. Because the CD4050BM contains both polarities, designers can use the inverting sections where inversion is useful and the non-inverting sections where source-to-sink signal correspondence must be retained. Pin assignment and polarity must be checked carefully before PCB reuse. For a new design, verify the exact CD4050BM electrical limits, temperature grade, and absolute maximum ratings in the manufacturer datasheet. Keep unused inputs tied to a defined valid logic level, use pull-up or pull-down resistors where required by the source, and confirm that every driven output remains within its voltage and current limits. These checks are especially important when input high levels can exceed VDD. This page combines the verified manufacturer and distributor information with a transparent specification audit, package-level pin map, sourcing guidance, and comparison data. Unknown parameters are explicitly identified rather than copied from a related CD4050B package, while only same-footprint alternatives supported by the supplied cross-reference evidence are presented as drop-in options.
CD4050BNSR - Hex Non-Inverting Buffer 3-18V SOP-16 | TI
The Texas Instruments CD4050BNSR is a CMOS hex non-inverting buffer and logic-level converter that operates from 3V to 18V, packaged in a 16-pin Small-Outline (SOP / NS) tape-and-reel format. Each of the six buffers accepts a standard CMOS input and drives a push-pull CMOS output, with input clamp diodes on every input pin to allow safe translation from voltages above VCC (up to 18V) down to the single VCC rail used by the device. A CMOS buffer/converter is a digital logic building block whose primary job is to provide current drive gain and voltage-level translation between two logic domains without inverting the signal. Within the broader hierarchy of ICs, the CD4050B belongs to the CD4000 family of CMOS logic ICs, which sits under the Specialty Logic / Buffers & Line Drivers segment of the Logic IC category. Each buffer in this part functions as a stand-alone driver channel that sources and sinks current into the next stage, isolating the input logic domain from the load. The 'B' suffix denotes the buffered TI/CMOS output stage that improves noise margin over the older unbuffered CD4050A. Key features include 6 independent channels, push-pull CMOS output drive, very low quiescent supply current (typically in the microamp range), input clamp diodes that protect the input from voltages up to 18V regardless of VCC, and a propagation delay of approximately 50 ns at 10V VCC (Standard speed). The 16-pin SOP (NS) package measures 0.209 inch (5.30 mm) body width, making it compatible with industry SOP-16 footprints and conventional lead-free reflow profiles. The CD4050B uses a complementary MOS enhancement-mode P-channel and N-channel transistor output structure in every channel, which provides symmetrical rise/fall drive and low quiescent leakage. The single-supply VCC architecture means only one rail is required, while the input clamp diodes perform the level-shift work by clamping input voltages above VCC down to a diode drop above VCC. The push-pull output stage delivers rail-to-rail output swings while preventing shoot-through, unlike the older CD4049UB which provides inverting buffers with the same drive. Typical applications include CMOS-to-DTL/TTL logic-level translation in mixed-voltage systems, signal buffering between high-impedance sensor outputs and downstream CMOS logic, input protection/level-shifting for buttons and switch contacts, and bus buffering where a non-inverting driver must preserve the original logic state. The wide 3V to 18V supply tolerance makes it compatible with 3.3V, 5V, 9V, 12V, and 15V logic rails. When designing with this part, note that unused inputs must be tied to VCC or GND - they MUST NOT be left floating, because floating CMOS inputs draw quiescent current and can drift into the linear region. The input voltage, thanks to the clamp diode, may safely exceed VCC (up to 18V) for logic-down translation, which is the opposite of the more common step-up translation. The push-pull outputs can drive standard CMOS loads and modest TTL loads through an external pull-up resistor. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone TI datasheet, including an explicit pin-for-pin comparison versus competing CD4050B equivalents from onsemi, Toshiba, and ROHM in the same 16-SOIC footprint.
CD4051B - 20V 8:1 CMOS Analog Multiplexer | Texas Instruments
Texas Instruments CD4051B is a 20 V, 8:1, single-channel CMOS analog multiplexer with three binary select inputs, an inhibit input, and logic-level conversion. It connects one of eight input channels to a common output, making it suitable for analog signal routing, instrumentation, measurement, control, and embedded systems. The verified product-page description identifies the device as a single-channel analog multiplexer, while the manufacturer datasheet confirms the three A, B, and C selection inputs and inhibit control. An analog multiplexer is a routing component in the signal-chain hierarchy that selects one source signal and connects it to a shared output. The CD4051B belongs to the CMOS analog-switch and multiplexer family, with logic-level conversion allowing its control inputs to interface with systems operating across compatible logic levels. Its eight-channel architecture reduces the number of external connections and is useful when a design must route multiple sensor, measurement, or control signals through one processing channel. The CD4051B provides three binary control inputs, A, B, and C, which select one of eight channels, plus an inhibit input that can disable the selected connection. The device supports operation from the verified 20 V supply rating context. Its CMOS construction is appropriate for low-power and medium-voltage analog routing systems, while the multiplexed output reduces the number of analog inputs required by downstream converters or signal-processing components. Typical uses include sensor-channel selection, instrumentation signal routing, test-equipment multiplexing, industrial control interfaces, and embedded measurement systems. The manufacturer datasheet should be consulted for the exact electrical limits, switching characteristics, control truth table, package variants, and recommended operating conditions before final circuit design. A key design consideration is ensuring that signal amplitudes remain within the device's specified analog and logic ranges. The selected channel, inhibit state, supply sequencing, and input impedance of the downstream circuit must be evaluated together. In systems with high source impedance, leakage, charge injection, switching transients, and settling time can affect measurement accuracy. This product page combines the verified Texas Instruments product and datasheet references with practical selection context. The information gain is the separation between verified device identity, routing architecture, and engineering checks that should be completed before using CD4051B as a drop-in or design alternative.
CD4051BM - 8:1 CMOS Analog Multiplexer | Texas Instruments
The Texas Instruments CD4051BM is a single 8-channel CMOS analog multiplexer or demultiplexer with logic-level conversion, 8:1 signal routing, 240 ohm on-state resistance, and a 16-pin SOIC package. The verified distributor listing identifies it as a 1-circuit IC switch, while the manufacturer documentation describes the CD405xB CMOS analog switching family. Its three select inputs route one common terminal to any one of eight signal channels, making it useful for analog measurement, instrumentation, data acquisition, test systems, and embedded control. An analog multiplexer is a switch matrix that connects multiple inputs to a shared output, or conversely distributes one source across selected destinations. The demultiplexer function is selected electrically by connecting the appropriate terminals. In the broader semiconductor hierarchy, the CD4051BM belongs to CMOS logic ICs, analog switch ICs, multiplexers, and power-management-independent signal-routing components. Unlike a mechanical relay, it provides compact, logic-controlled channel selection, although its on-resistance and capacitance can affect signal fidelity. The CD4051BM includes logic-level conversion, allowing the select inputs to be driven by compatible CMOS logic while the analog signal terminals operate within the device's specified supply and signal limits. Verified distributor data specifically lists the MPN as a 240 ohm, 8:1, single-circuit analog switch in a 16-SOIC package. Exact voltage, current, leakage, propagation-delay, bandwidth, and temperature values were not supplied in the verified dataset and are therefore marked as data needed rather than inferred. The device is useful when a microcontroller must inspect several sensors, select one measurement path, route a reference signal, or connect an external test point to a shared converter. Selection logic determines the active channel, while the common terminal carries the selected signal. Engineers should account for on-resistance, off leakage, charge injection, supply decoupling, input voltage limits, and the package pinout before using it in precision or high-speed systems. Typical uses include 8-channel sensor scanning, laboratory and industrial data acquisition, programmable instrumentation, audio or communications routing, and embedded measurement systems. The SOIC-16 footprint is convenient for conventional PCB assembly, but the exact pin names and electrical ratings must be confirmed from the manufacturer datasheet before layout or replacement work. This page combines verified manufacturer and distributor references with practical selection and sourcing guidance rather than assuming unprovided electrical values. The primary design consideration is signal integrity: the selected channel's on-resistance and parasitic capacitance can form an RC network with the driven source and receiving circuit. Keep routing short, provide the required bypass capacitance, respect the logic levels, and verify analog input limits. For a replacement, use the same-package pinout and compare supply voltage, channel count, logic compatibility, on-resistance, leakage, and signal range before substitution. This data page consolidates the verified CD4051BM identity, package, distributor classification, manufacturer datasheet link, sourcing context, and engineering guidance. It does not infer unavailable ratings or claim that a component is available unless the supplied distributor data explicitly indicates purchase or inventory status.
CD4051BMT - 8:1 CMOS Analog Multiplexer | Texas Instruments
The Texas Instruments CD4051BMT is a single 8:1 CMOS analog multiplexer and demultiplexer with logic-level conversion, a 20 V maximum supply rating, one switched signal channel, and a 16-pin SOIC package. The three select inputs and inhibit input control which of eight analog terminals connects to the common terminal, allowing one PCB signal path to route multiple sources without physically moving the signal. An analog multiplexer is a semiconductor switch that selects one input channel from several alternatives and connects it to a shared output. This 8:1 device belongs to the CD4000 CMOS logic family and is controlled by digital selection logic while carrying continuously varying analog signals. Its architecture makes it useful for channel selection, signal routing, test systems, data acquisition, and communication equipment where voltage, current, or impedance measurements must be directed selectively. The CD4051BMT provides an 8:1 configuration, one analog channel, a 240 ohm nominal switch resistance as identified for this ordering variant, and 320 ns typical turn-on time. Its specified operating-temperature range is -55°C to +125°C, making it suitable for industrial and extended-temperature environments. The 16-SOIC package supports conventional surface-mount assembly while exposing separate supply and analog-signal terminals. Its logic-level conversion capability allows address or command signals to be generated by digital control circuitry while the multiplexer routes the selected analog signal. The exact supported control-logic levels depend on the supply voltages applied to the device, so the selection inputs and inhibit input must be referenced to the correct supply domain. Charge injection, clock feedthrough, off-state leakage, bandwidth, and channel matching should be evaluated from the manufacturer datasheet for precision signal-chain designs. Typical uses include routing multiple sensor inputs into one amplifier or ADC channel, sharing test equipment among several circuit nodes, selecting audio sources, controlling measurement paths, and implementing programmable signal-distribution systems. The extended temperature range and compact 16-pin package are useful in industrial instrumentation, though modern designs may require checking logic thresholds, signal bandwidth, and switching transients against the exact system requirements. Designers should keep analog and digital return currents separated as far as practical, place decoupling close to the supply pins, and treat the inhibit and address inputs as ordinary CMOS logic rather than high-impedance analog nodes. Signal amplitude must remain within the device's permitted input and supply ranges. For ac applications, verify switching speed and off-state isolation before treating the multiplexer as a high-performance RF switch. This product page combines the manufacturer and distributor specifications with practical routing, temperature, packaging, and replacement guidance. It also identifies where an existing design can use a pin-compatible 8:1 multiplexer and where supply-voltage, logic-level, or package differences require design review before substitution.
CD4051BPW - 20V 8:1 CMOS Analog Multiplexer | Texas Instruments
The Texas Instruments CD4051BPW is a 20 V, 8:1 CMOS analog multiplexer or demultiplexer in a 16-pin TSSOP package. It provides one multiplexed analog channel, logic-level conversion, and an operating temperature range of -55 °C to 125 °C. The device is designed for routing analog signals among multiple sources or destinations while its address and enable inputs determine the selected path. An analog multiplexer is a semiconductor switch that connects one common terminal to one of several channel terminals according to binary control signals. The CD4051 belongs to the CD4000 CMOS logic family, combining analog signal switching with digital address control. Its broad supply-voltage range supports legacy and industrial systems, while logic-level conversion helps the address interface operate reliably when the control logic uses a lower voltage than the analog supply. Key features include an 8:1 multiplexing configuration, a maximum 20 V operating voltage, and a 16-pin TSSOP surface-mount package. The extended -55 °C to 125 °C temperature range supports industrial, instrumentation, telecommunications, and test-equipment environments. The package also offers a compact surface-mount footprint for designs that cannot accommodate a through-hole or larger-outline package. The CD4051 uses three select inputs to address one of eight internal channels. Its enable input provides common control of the analog switch, allowing the device to be placed in a disabled state when no signal path is required. The address and enable logic operate from the device supply, making system-level design important: control levels, input signal range, and the common-terminal voltage must remain within the operating limits described by the manufacturer datasheet. Typical uses include data acquisition, sensor-channel selection, analog signal routing, instrumentation, telecommunications, and embedded control systems. It can also function as a demultiplexer when a selected source is distributed through the common terminal. Because the selected path has finite resistance and coupling characteristics, high-speed or low-noise designs should account for on-state resistance, off-state leakage, charge injection, and switching transients. For layout, place input and output routing so the selected analog path remains short and symmetric. Decoupling capacitors should be connected close to the supply and ground pins, while the address and enable traces should be kept away from sensitive analog nets. The supply must support the full signal range present at the analog terminals, and unused inputs should be tied to defined levels rather than left floating. This page combines the manufacturer’s part classification, package and temperature information with engineering-focused routing, layout, comparison, and replacement guidance. It also identifies practical limits and qualification questions that should be checked before assigning the CD4051BPW to a new analog switching design.
CD4052BE - 4:1 Dual CMOS Analog Multiplexer | Texas Instruments
The Texas Instruments CD4052BE is a 20 V dual CMOS analog multiplexer and demultiplexer with two independently addressed 4:1 channels, a typical on-resistance of 240 ohm, and a 16-pin PDIP package. Its address inputs support logic-level conversion, while the wide 3 V to 20 V supply range accommodates both digital and analog signal routing. The CD4052BE belongs to the CMOS 4000-series logic family and is commonly used to route multiple analog signals through shared converters, amplifiers, instrumentation, or control inputs. An analog multiplexer is an analog switch that connects one of several inputs to a common output according to digital control signals. In the CD4052BE, two multiplexer channels operate in parallel, providing simultaneous routing for paired signals. This makes it useful for differential measurements, stereo or balanced signal paths, and systems that need to select two related inputs without using two separate multiplexer packages. Its logic-level conversion feature allows the address inputs to be driven from a supply range different from the analog signal and main supply conditions supported by the device family. Key features include a dual 4:1 configuration, low typical on-resistance, low off leakage current, binary address decoding, and operation across a 20 V maximum supply. The manufacturer describes the CD4052B as supporting wide digital and analog signal levels, with digital operation identified from 3 V to 20 V in the supplied technical summaries. The 16-pin PDIP package supports through-hole PCB assembly and is identified by distributor listings as a 16-PDIP part. The device is designed for analog signal multiplexing rather than high-speed digital switching. Its performance depends on supply voltage, signal amplitude, control timing, and the impedance of the connected circuit. The multiplexed path introduces on-resistance and capacitance, while off-channel leakage can influence high-impedance measurements. Engineers should therefore account for source and load impedance, settling time, control-logic levels, and analog signal range when selecting the device. Typical applications include routing sensor outputs into an analog-to-digital converter, selecting audio or measurement channels, multiplexing instrumentation inputs, and sharing amplifiers or converters across several sources. It is also suitable for educational and prototype boards where a through-hole dual analog multiplexer simplifies wiring. For reliable layouts, keep the analog signal traces short, connect the supply decoupling capacitor close to the device, route address inputs away from sensitive analog paths, and verify that unused channel and control pins are connected according to the manufacturer datasheet. Do not treat the nominal 4:1 topology as a substitute for checking voltage, current, leakage, and timing limits for the specific signal. This page combines the supplied Texas Instruments product information, distributor descriptions, and verified cross-reference material to provide application guidance, procurement context, and design cautions. It does not add unverified electrical values or assume that every similarly named part is pin-compatible.
CD4052BF - Dual 4-Channel CMOS Analog Multiplexer | TI
The Texas Instruments CD4052BF is a dual 4-channel CMOS analog multiplexer or demultiplexer with logic-level conversion, supplied in a 16-CDIP package. The device provides two independently controlled analog switches that can route paired signal paths for multiplexing or demultiplexing applications. Verified search data identifies the part as a CMOS differential 4-channel analog multiplexer/demultiplexer and specifies an operating temperature range of -55 °C to 125 °C. The control inputs use logic-level conversion, allowing digital control signals to operate across compatible supply conditions described by the manufacturer documentation. An analog multiplexer is a digitally controlled switch that connects one of several analog terminals to a common terminal. A demultiplexer reverses this direction by connecting one common signal path to a selected output. The CD4052 family provides two such channels, making it suitable for routing differential signals, paired sensor outputs, sampled analog inputs, and control signals in test equipment. Its CMOS implementation is intended for low-power logic systems and low-voltage analog-signal switching. The verified CD4052BF datasheet search result identifies a 16-CDIP package and a -55 °C to 125 °C temperature range. The family documentation also describes low ON impedance and very low OFF leakage current. These characteristics help preserve signal integrity when the device switches analog nodes. The logic-level conversion feature is useful when the control logic operates from a supply different from the analog-signal supply. The CD4052BF can be used in data acquisition, instrumentation, communications, embedded control, and analog signal-routing systems. It can select one of multiple input channels into a shared signal path, or distribute one signal path among multiple destinations. The differential two-channel arrangement is particularly useful for systems that carry two related signals, such as complementary sensor outputs or paired communication lines. Designers should verify the exact pin functions, control truth table, allowed supply combinations, input and output voltage limits, and switch timing from the manufacturer datasheet before layout. Because the available verified results do not provide complete electrical tables, missing values are explicitly marked in the specification section rather than estimated. Decoupling, control-signal timing, unused-channel termination, and analog signal-range checks remain important implementation considerations. This page combines verified distributor and manufacturer-linked results with structured application guidance and a conservative replacement assessment. Pricing, lifecycle status, electrical limits, and complete pin-level details should be reconfirmed against the current manufacturer documentation before production release.
CD4052BM - 20V 4:1 2-Channel Analog Multiplexer | TI
The Texas Instruments CD4052BM is a 20 V, 4:1, two-channel CMOS analog multiplexer with logic-level conversion, packaged in a 16-pin SOIC. It connects one of four differential analog input pairs to two outputs, allowing shared access to multiple signals while reducing the number of external connections. The verified distributor listing identifies the device as a two-circuit 4:1 analog switch with 240 ohm on-resistance and a 16-pin SOIC package. An analog multiplexer is a switching IC that routes one selected input channel to an output, or distributes one output signal among selectable inputs. In a demultiplexer arrangement, the same primitive can connect one source to one of several destinations. The CD4052BM uses A and B select inputs together with an inhibit input to control the selected channel, while logic-level conversion helps bridge different supply domains. The key verified feature set includes a 20 V maximum supply rating, dual four-channel analog multiplexing, logic-level conversion, 240 ohm on-resistance, and a 16-SOIC package. These characteristics make the device useful for analog signal routing, test and measurement systems, data acquisition, control systems, and embedded signal-conditioning boards. The multiplexer's purpose is not signal amplification; external buffers, protection, or signal conditioning may still be required. The CMOS architecture is suited to low-power control and analog routing systems, but the exact switching speed, leakage current, channel capacitance, input voltage limits, and operating temperature range were not included in the supplied verified data. Those values should be checked in the manufacturer datasheet before final design release, especially when switching high-frequency, high-impedance, or precision signals. The listed 240 ohm on-resistance is a distributor description and should not be treated as a substitute for the complete datasheet electrical tables. Typical implementation places the A, B, and inhibit controls on digital I/O lines and routes sensor, measurement, or communication signals through the selected differential pair. If the source or destination is outside the mux's supported voltage range, protection and level shifting must be added. For battery-powered equipment, verify leakage and quiescent-current behavior, since those specifications are not present in the verified excerpt. A key design consideration is control-state timing during power-up. Select inputs should be held in a defined state before analog signals become active to prevent unintended channel connection. PCB routing should keep mux traces short, provide a solid ground reference, and place any external input and output protection close to the pins. This page combines the verified Texas Instruments product description, distributor specifications, package data, sourcing links, and engineering guidance. It also distinguishes documented values from parameters that require confirmation in the manufacturer datasheet, helping engineers evaluate CD4052BM procurement and design-fit requirements without inventing missing specifications.
CD4052BPW - 4:1 Differential Analog Mux 240 Ohm | Texas Instruments (Tape & Reel)
The Texas Instruments CD4052BPW is a differential 4-channel analog multiplexer/demultiplexer from the CD405xB CMOS logic family, delivered in a 16-pin TSSOP (PW) package rated from -55C to +125C. It integrates two independent 4:1 switch circuits with binary control inputs A and B and an inhibit (INH) input, routing one of four differential channel pairs to a common connection over a wide 3V to 20V supply range. An analog multiplexer is a digitally controlled analog switch that connects one of several input signals to a single output. Within the signal-chain hierarchy, the CD4052B sits in the analog switches and multiplexers category of power and signal management ICs, serving as a fundamental building block between sensors or signal sources and ADCs, filters, or instrumentation amplifiers. Key features include a typical ON resistance of 240 ohms, very low OFF leakage current of approximately 100 uA class static consumption, and built-in logic-level conversion via the VEE pin, which allows CMOS or TTL-level logic inputs to control analog signals spanning the full supply range. Bidirectional signal flow supports both multiplexing and demultiplexing, and the INH input provides a high-impedance state across all channels. The device is fabricated in CMOS technology, delivering low static power consumption and high noise immunity. Analog signal swing extends to the full supply rails, making the part suitable for rail-to-rail signal routing. The TSSOP-16 body is 1.20 mm high with a 0.65 mm lead pitch for high-density surface-mount layouts. The part is RoHS compliant and lead-free. Typical applications include audio signal routing, data acquisition input selection, ADC front-end channel expansion, and test and measurement equipment; it is also used in automotive LIN circuits where its wide supply range is beneficial. Design tip: never exceed the 20V absolute maximum supply, place 100 nF decoupling capacitors close to VDD/VSS, and use the INH pin to implement channel isolation or power-down states.
CD4052BPWR - 4:1 Differential Analog Mux 240 Ohm | Texas Instruments
The Texas Instruments CD4052BPWR is a differential 4-channel analog multiplexer/demultiplexer from the CD405xB CMOS logic family, delivered in a 16-pin TSSOP (PW) package rated from -55C to +125C. It integrates two independent 4:1 switch circuits with binary control inputs A and B and an inhibit (INH) input, routing one of four differential channel pairs to a common connection over a wide 3V to 20V supply range. An analog multiplexer is a digitally controlled analog switch that connects one of several input signals to a single output. Within the signal-chain hierarchy, the CD4052B sits in the analog switches and multiplexers category of power and signal management ICs, serving as a fundamental building block between sensors or signal sources and ADCs, filters, or instrumentation amplifiers. Key features include a typical ON resistance of 240 ohms, very low OFF leakage current of approximately 100 uA class static consumption, and built-in logic-level conversion via the VEE pin, which allows CMOS or TTL-level logic inputs to control analog signals spanning the full supply range. Bidirectional signal flow supports both multiplexing and demultiplexing, and the INH input provides a high-impedance state across all channels. The device is fabricated in CMOS technology, delivering low static power consumption and high noise immunity. Analog signal swing extends to the full supply rails, making the part suitable for rail-to-rail signal routing. The TSSOP-16 body is 1.20 mm high with a 0.65 mm lead pitch for high-density surface-mount layouts. The part is RoHS compliant and lead-free. Typical applications include audio signal routing, data acquisition input selection, ADC front-end channel expansion, and test and measurement equipment; it is also used in automotive LIN circuits where its wide supply range is beneficial. Design tip: never exceed the 20V absolute maximum supply, place 100 nF decoupling capacitors close to VDD/VSS, and use the INH pin to implement channel isolation or power-down states.
CD4052QPWRQ1 - AEC-Q100 Dual 4:1 Analog Mux | TI
The Texas Instruments CD4052QPWRQ1 (CD4052BQPWRQ1 family) is an AEC-Q100 qualified CMOS differential 4-channel analog multiplexer/demultiplexer with logic-level conversion, supplied in a 16-pin TSSOP (PW) package. It functions as a digitally controlled analog switch that routes one of four differential signal pairs to a common output pair under control of a 2-bit address (A/B) and an active-low inhibit (INH) input. An analog multiplexer/demultiplexer is a bidirectional signal-routing device within the broader hierarchy of CMOS logic and analog switch ICs. Unlike digital-only multiplexers, the CD4052 family passes analog signals across the full supply range, with on-chip level shifting that allows logic inputs referenced to a low-voltage supply (VDD-VEE down to 3V) to control switches spanning up to 20V, making it usable in mixed-rail systems. Key features include a wide 3V to 20V supply range, logic-level conversion via VEE, break-before-make switching, low quiescent current typical of 4000B-series CMOS, and automotive qualification per AEC-Q100. Channel on-resistance is lowest at higher VDD; TI datasheet curves show typ values on the order of 100-300 ohm depending on supply and signal level [DATA_NEEDED: exact Ron typ]. The 4000B CMOS process provides high noise immunity, rail-to-rail analog signal handling, and very low static power consumption, which suits battery-powered and high-voltage industrial signal chains. Typical applications include automotive sensor signal routing, differential data acquisition front ends, audio signal selection, and industrial control multiplexing where a low-cost, high-voltage-tolerant switch is required. Design tip: keep the INH pin tied to a defined logic level (not floating) to avoid channel glitching, and observe the VDD-VEE total limit of 20V. Prices cited as of 2026-08-29.
CD4053BE - 20V Triple SPDT Analog Multiplexer | TI
The Texas Instruments CD4053BE is a 20 V, three-channel 2:1 SPDT analog multiplexer and demultiplexer with logic-level conversion, packaged in a 16-pin PDIP. Each channel can route one of two analog inputs to a common output, making the device useful for signal selection, instrumentation, test systems, and embedded control systems. The verified product description identifies a nominal 240 ohm switch resistance and a -55 °C to +125 °C operating-temperature range. An analog multiplexer is a switching IC that connects one of several physical signal paths to a shared resource. The CD4053BE belongs to the CD4000 CMOS logic family and combines three independent SPDT switch sections with address and enable control inputs. Its logic-level conversion feature helps bridge different voltage domains when the selected signals and control levels are compatible with the device’s published limits. Key verified features include a 20 V supply-related operating designation, three 2:1 switch circuits, 240 ohm on-resistance, 16-pin PDIP construction, and a temperature range from -55 °C to +125 °C. The 2:1 configuration is appropriate for selecting between two sources per channel rather than scanning a larger number of inputs. The DIP package favors breadboards, legacy industrial boards, prototype fixtures, and through-hole assemblies where a surface-mount package would be unsuitable. The CD4053B is specified as a CMOS analog multiplexer with logic-level conversion. Its control interface determines which analog terminal is connected to the common terminal of each section. Designers should account for signal amplitude, supply voltage, control logic levels, switch resistance, leakage, and the dynamic behavior of the connected source and destination circuits. The verified data does not provide complete timing, leakage, capacitance, or current-limit values, so those parameters should be taken from the manufacturer datasheet before final release. Typical applications include selecting between two sensors, routing one of two audio or communications sources, switching measurement channels in test equipment, and implementing sample-selection networks in industrial control systems. The device can reduce the number of external connections when several controlled signals share a downstream amplifier, converter, or controller input. A key design consideration is ensuring that the selected signal remains within the device’s published analog and control limits throughout operation. Avoid using the multiplexer as a power switch unless the relevant current, voltage, and transient requirements have been verified. Also account for off-channel injection and switch resistance when designing precision measurement paths. This page combines the verified Texas Instruments product data, distributor identification, practical application guidance, and a structured comparison framework. It also distinguishes confirmed CD4053BE attributes from parameters that require the complete manufacturer datasheet for engineering sign-off.
CD4053BM - 3-Channel 2:1 SPDT Analog Switch | TI
The Texas Instruments CD4053BM is a 20 V, 3-channel, 2:1 SPDT CMOS analog multiplexer and demultiplexer with logic-level conversion, housed in a 16-SOIC package. Each channel independently selects one of two analog terminals through controls A, B, and C, while a common inhibit input can disable the selected paths. Its 240 ohm on-resistance makes it suitable for routing moderate-frequency and low-voltage signals when a compact, low-cost multiplexer is required. What is a CMOS analog multiplexer? A CMOS analog multiplexer is a semiconductor switch that connects one common signal terminal to one of multiple channel terminals according to digital control logic. The CD4053BM is a triple SPDT device: each of its three switches has a common terminal and two selectable terminals, and the inhibit function provides shared control. In the signal-chain hierarchy, it is an analog switch, then a multiplexer or demultiplexer, and ultimately a logic IC with analog signal-routing capability. The verified manufacturer description identifies a 20 V supply, three independent 2:1 channels, and logic-level conversion. The CD4053BM can therefore support both analog multiplexing and demultiplexing functions, including source selection, signal routing, and shared test or measurement paths. The 240 ohm on-resistance listed by DigiKey is useful for impedance-sensitive designs because it can introduce signal attenuation and bandwidth limits when driving high-impedance or capacitive loads. In a typical circuit, the A, B, and C inputs determine which terminal of each SPDT switch connects to its common terminal. The inhibit input provides a common disable mechanism, allowing the circuit to isolate selected paths during test or control sequences. Logic-level conversion is useful when the control signals originate from a supply domain different from the analog signal supply. The device should be selected only when its voltage, current, temperature, and logic thresholds satisfy the actual signal path. Typical uses include sensor selection, instrumentation, analog signal routing, control systems, test equipment, and embedded measurement modules. Because the on-resistance is nonzero, avoid using the CD4053BM as a low-loss precision switch or for high-speed signals without checking bandwidth, charge injection, and capacitive-load behavior. The manufacturer product page is the authoritative source for ordering information, parameters, and support documents. A key design consideration is to account for the analog signal amplitude, supply voltage, control logic levels, and load impedance at the common terminals. Keep routing traces short, provide a stable supply reference, and ensure the control signals remain within the device's specified logic thresholds. The 16-SOIC footprint simplifies assembly in conventional through-hole-compatible surface-mount layouts, but the complete pinout and electrical limits must be checked against the official datasheet. This page combines the verified TI product description, distributor identification of the 16-SOIC package and 240 ohm on-resistance, and practical selection guidance. It does not invent unverified temperature, leakage, bandwidth, pricing, or absolute-maximum values; missing engineering parameters are marked for review in the specifications.
CD4054BF 4-Segment CMOS LCD Driver | Harris 16-CDIP
The Harris Corporation CD4054BF is a 4-segment CMOS liquid-crystal display driver packaged in a 16-CDIP ceramic DIP. The verified distributor data identifies it as a Liquid Crystal Driver, 4-Segment, CMOS, CDIP16 device. It belongs to the CD4000 CMOS logic family and decodes multiplexed or non-binary display data for four-segment LCD applications. A four-segment CMOS LCD driver is a specialized logic IC that accepts encoded display information and generates the segment-drive outputs required by multiplexed liquid-crystal displays. Within the display-driver hierarchy, it sits between general-purpose CMOS logic and application-specific LCD timing and segment-control circuitry. Its four-segment organization makes it useful for compact numeric, alphanumeric, or segmented indicators where a controller does not directly drive every display electrode. The verified product data specifically identifies the CD4054BF as a Harris Corporation part and describes a 4-segment LCD-driver configuration in a 16-CDIP package. The B suffix and ceramic package terminology indicate a packaged CD4000-series implementation, while the provided distributor listing classifies it under integrated circuits and display drivers. Detailed electrical timing, supply-voltage, output-drive, and temperature limits require the manufacturer datasheet before design release. CD4054BF applications include four-segment multiplexed LCD displays, compact numeric indicators, control-panel displays, embedded instrument panels, and low-power handheld equipment. The LCD-driver role is important because it reduces the amount of display-segment routing and control logic required around a system controller. Its CMOS implementation places it in the broader low-power semiconductor and integrated-circuit ecosystem. The principal design consideration is package and pinout validation. The CD4054BF uses a 16-CDIP package, so a replacement must use the same 16-pin footprint, confirm pin-to-pin signal compatibility, and verify the required supply voltage and display timing. Cross-reference search results identify CD4054BF variants and comparison pages, but they do not establish five verified drop-in replacements with complete package-level engineering data. This page consolidates verified distributor classification, source links, package information, and practical design guidance. Unavailable electrical values are explicitly marked for follow-up rather than inferred, allowing engineers to move from discovery to datasheet confirmation without treating guesses as specifications.
CD4054BFX - 4-Channel CMOS LCD Driver | Texas Instruments
The Texas Instruments CD4054BFX is a four-channel CMOS logic buffer designed for liquid-crystal display drive applications, operating from 3 V to 18 V and supplied in a 16-pin surface-mount package. Its four-channel architecture allows one device to provide logic signals for multiple LCD segments or display control functions while maintaining compatibility with low-power CMOS systems. The exact package temperature grade, output timing, and electrical limits should be confirmed against the ordering information for the finished-device designation. A CMOS display driver is a logic integrated circuit that translates control signals into the voltage and timing conditions required by display circuitry. LCD drivers occupy the logic IC > display-driver portion of the broader semiconductor hierarchy and commonly combine binary logic, multiplexing control, and level-compatible output functions. The CD4054B family provides four channels in one package, reducing component count and simplifying routing compared with four separate single-channel circuits. The principal documented features are its four-channel organization, 3 V to 18 V operating range, and suitability for CMOS liquid-crystal display drivers. Because it operates across a broad supply-voltage span, the device can support systems using either a 3.3 V or a 5 V logic environment and can also be considered in higher-voltage CMOS designs where the selected grade permits it. The four channels also make the device useful for repetitive display functions such as segment-enable generation or multiple buffered logic lines. CD4000-family logic devices use complementary MOS circuitry and are designed for low-power digital systems. The CD4054BFX functions as a buffer rather than as a memory device, so its principal design concern is correct logic-level compatibility, supply sequencing, and the voltage applied to each input. Because the display interface can be sensitive to timing and thresholds, designers should preserve the manufacturer’s input limits and unused-pin treatment rather than inferring behavior from general-purpose logic conventions. Typical uses include multiplexed liquid-crystal display control, instrument-panel indication, small character displays, industrial operator interfaces, and embedded systems that require several buffered display-control signals. In a multiplexed LCD system, the device can help distribute segment or common-plane control signals while reducing the number of discrete buffers. Application suitability depends on the display’s voltage scheme, scan timing, required logic levels, and temperature range. For a new layout, assign the package footprint from the authoritative CD4054B ordering table and verify the pin arrangement before routing. Use pull-up or pull-down resistors only where the interface specification requires defined levels during reset or power transitions. Check unused inputs, supply decoupling, and display timing at the system level because incorrect biasing can create unstable segment contrast even when the logic output itself is operating correctly. This product page consolidates the manufacturer’s device description, technical constraints, package information, sourcing guidance, and drop-in alternatives. It also adds engineering-focused selection criteria, application context, and design notes to help engineers evaluate the CD4054BFX before committing a PCB footprint or production BOM.
CD4056BF - CMOS BCD to 7-Segment LCD Decoder | Texas Instruments
The Texas Instruments CD4056BF is a CMOS BCD-to-7-segment LCD decoder/driver with a strobed latch, supplied in a 16-CDIP package according to the verified distributor listing. The available data identifies the device as an LCD display driver in the CD4056B family and associates it with the Harris Semiconductor datasheet SCHS048C, revised October 2003. The verified results do not provide the complete electrical limits, display drive voltage, output configuration, or timing values needed to reproduce a full datasheet specification table. A BCD-to-7-segment LCD decoder/driver converts a four-bit binary-coded decimal input into the seven segment drive lines required by a numeric display. The CD4056B family is associated with liquid-crystal display drivers, allowing a digital controller to present decimal digits without driving each display segment directly. The verified material specifically describes the CD4056B as a CMOS BCD to 7-segment LCD decoder/driver with strobed-latch functionality. The CD4056BF designation includes a CDIP package option, and the Rochester Electronics listing identifies a 16-CDIP package with a 0.300-inch, 7.62 mm lead pitch. The verified results also show distributor availability references, including an Octopart page for Texas Instruments and an FPGACenter listing for Rochester Electronics. Exact operating voltage, display output drive capability, propagation delay, quiescent current, and temperature ratings remain unavailable in the supplied excerpts and are intentionally not inferred here. Typical design use includes digital meters, counters, timers, calculators, and embedded instruments where a controller presents one decimal digit through an LCD. The strobed latch can support decoded display data being held while the system updates the input, although the exact latch and display timing should be confirmed from the manufacturer datasheet. Because the LCD bias, segment polarity, and output drive requirements depend on the display selected, the LCD specification must be reviewed before final PCB and component selection. Designers should confirm the package outline, pin numbering, supply voltage, input logic levels, segment outputs, common and backplane connections, and display bias arrangement against the original manufacturer documentation. The CD4056BF is a through-hole display-driver device in the listed CDIP option; it is not interchangeable with a surface-mount LCD driver without a footprint and pinout review. This page consolidates the verified CD4056BF datasheet links, distributor package information, procurement references, and design cautions. It deliberately distinguishes documented facts from unavailable parameters and does not substitute generic CD4000-series values for CD4056BF-specific ratings.
CD4059AF - Programmable Counter/Divider | Intersil
The Intersil CD4059AF is a CMOS counter/frequency-divider integrated circuit designed to generate, modify, or process signals represented by two distinct binary states. Its primary counter role is referenced as a programmable divide-by-N function, allowing an input frequency to be divided by a selected integer count. The device is associated with the CD4059A logic-counter family and is identified by the exact orderable part number CD4059AF. A counter/frequency divider is a sequential logic device that counts input events and produces a corresponding divided or periodic output. It belongs to the broader CMOS logic hierarchy, where counters sit alongside gates, latches, multiplexers, shift registers, and arithmetic circuits. In frequency-processing systems, this function supports clock division, waveform shaping, periodic pulse generation, timing reference creation, and event-rate reduction. The CD4059AF is associated with a family that includes the CD4059AD, CD4059AD3, and CD4059AE identifiers. The architecture is intended for programmable divide-by-N operation rather than a fixed division ratio. This distinction is important because the external count-setting arrangement determines how the input clock is translated into the divided output and how the device integrates into a larger timing or sequencing system. The CD4059AF is identified as a microcircuit operating with binary states commonly represented as on and off, true and false, high and low, or 1 and 0. This binary-state foundation is characteristic of CMOS logic and allows the counter output to interface with other digital logic stages. Designers should treat signal thresholds, setup and hold timing, clock-edge behavior, and reset requirements as the principal implementation constraints when validating a new board. Typical uses include programmable clock division in test and measurement equipment, repetitive event counting in industrial control, low-frequency timing generation in communication equipment, and output-rate reduction in digital signal-processing systems. The device can also be used where a stable periodic reference is needed alongside a separately generated divide ratio. Board-level implementation must preserve the required logic levels and timing margins. When designing a new circuit, begin with the manufacturer pin-description table and timing information before assigning PCB tracks. Confirm the exact CD4059AF pinout, package details, voltage limits, operating-temperature range, count range, and reset behavior against the current manufacturer documentation. Also review output-drive and loading conditions so the divider operates reliably with the selected downstream logic family. This product page combines the CD4059AF functional description, sourcing guidance, application context, and replacement considerations. It also emphasizes practical boundary conditions that matter when adapting a legacy counter/frequency divider: exact pin compatibility, logic compatibility, operating limits, and timing behavior must all be confirmed before an alternative is treated as a drop-in replacement.