Logic ICs
بەرهەمەکان (720+)
CD4029BD - 11MHz Up/Down Counter | Texas Instruments
Texas Instruments CD4029BD is a CMOS presettable binary and decade up/down counter with a rising-edge clock, an operating voltage range of 3 V to 18 V, and a maximum clock frequency of 11 MHz. The device is offered in a 16-pin CDIP package measuring 0.300 inches, or 7.62 mm, across the lead span. It is designed for digital counting, sequencing, and control systems where programmable count states and directional counting simplify control logic. A CMOS up/down counter is a digital logic IC that increments or decrements a binary count in response to clock transitions and control signals. The CD4029BD family belongs to the CD4000 CMOS logic hierarchy, combining counter, divider, and control functions in a single integrated circuit. Unlike a general-purpose microcontroller, it provides dedicated counting hardware that can operate deterministically with limited external logic, making it useful in timing, event-counting, and industrial control applications. The counter supports binary or decade counting configurations, allowing it to be adapted to different numerical bases and counting sequences. Its rising-edge triggering means the count changes on the active clock transition rather than throughout the high or low interval. The 11 MHz operating point supports relatively fast counting for a classic CMOS logic device, while the broad 3 V to 18 V supply range allows operation across multiple supply environments. The CDIP-16 package is a through-hole format intended for insertion into printed circuit board sockets or plated holes. Its lead arrangement follows the 16-pin dual in-line package format, with two rows of eight leads on a 0.300-inch pitch. Ceramic-sealed CDIP construction can also support applications requiring environmental protection and stable operation over a broad temperature range. Typical uses include industrial event counters, programmable timers, frequency division, test-equipment sequencing, digital control loops, and embedded counters that supplement a host microcontroller. Designers should confirm clock edge behavior, mode controls, and output states against the manufacturer pin description and truth table before committing a PCB layout. The principal design considerations are supply decoupling, clock-signal integrity, and correct handling of asynchronous control inputs. A low-impedance bypass capacitor should be placed close to the power pins, while the clock trace should remain short and avoid crossing noisy switching nodes. The counter should also be initialized to a known state if the system depends on a defined count after power-up. This product summary combines the manufacturer product description with package, operating-range, and clock-frequency information and adds practical guidance for selecting and implementing the CD4029BD in count-and-control systems.
CD4029BD3 - 4-Bit CMOS Up/Down Counter | Harris
The Harris CD4029BD3 is a 4-bit CMOS presettable binary up/down counter IC with one counting element, positive-edge clock operation, and a 16-pin ceramic dual in-line package. It is designed to count upward or downward under control of a dedicated direction input, making it suitable for sequencing, timing, digital control, and industrial logic systems. A counter IC is a synchronous state element that advances its binary output according to clock and control signals. The CD4029BD3 belongs to the CD4000 CMOS logic family, combining a 4-bit counting element, parallel load capability, and separate up/down control in one integrated package. Its principal function is to maintain a binary count that can be loaded, incremented, or decremented according to the external logic state. The CD4029BD3 is identified as a positive-edge counter with a 4-bit count section. Positive-edge operation means the counting state changes in response to the active clock transition rather than a change in clock level. Parallel load control allows the counter to receive an initial binary value, while the direction input determines whether subsequent clock events increment or decrement that value. These features support repeatable state-machine and event-counting implementations. Because it is part of the CD4000 CMOS logic series, the CD4029BD3 is designed for low-power digital operation and operation from a single supply. Its family architecture supports complementary binary and decade counting applications through external logic and wiring. The 16-CDIP construction is mechanically distinct from surface-mount variants, so replacement decisions must account for lead pitch, insertion geometry, row spacing, and thermal requirements rather than function alone. Typical uses include industrial sequence controllers, programmable event counters, machine-control timing modules, test and measurement counters, and digital systems requiring reversible binary counting. The part can also serve as the counting element in frequency-divider or state-advance arrangements when the surrounding logic defines the permitted count range and direction behavior. PCB implementation should preserve the manufacturer-defined clock and control timing, route sensitive counter inputs away from noisy switching nodes, and provide a stable ground reference. Because legacy CD4000 parts are commonly offered in through-hole ceramic packages, check mechanical tolerances and connector accessibility before substituting a molded-plastic or surface-mount implementation. The counter’s operating voltage, current, temperature range, and timing limits must be confirmed against the appropriate family documentation.
CD4029BE - 4-Bit CMOS Presettable Up/Down Counter | Texas Instruments
The Texas Instruments CD4029BE is a 4-bit CMOS presettable binary/BCD decade up/down counter operating from 3 V to 18 V with a maximum clock frequency of 11 MHz, packaged in a 16-pin PDIP (N) through-hole package rated for -55 C to +125 C. A counter IC is a member of the logic IC family: it belongs to the digital logic hierarchy that runs from counter and divider blocks up to logic gates, then to digital integrated circuits, and finally to semiconductor devices. The CD4000 series, of which the CD4029B is a member, is the classic complementary-MOS (CMOS) logic family recognised for wide supply-voltage tolerance, high noise immunity and low power consumption compared with 74xx TTL logic. The CD4029B is the counting block of that family that can count either up or down, in binary or in BCD decade mode. Key features of the CD4029B include a single clock input with look-ahead carry in both counting modes, a Binary/Decade select input, an Up/Down control input, a Preset Enable input, a Load input and four individual preset (J) data inputs, plus four counter outputs Q1 to Q4 and a Carry Out output. The counter is fully synchronous and advances on the positive clock edge, so state changes are clean and predictable for digital control and sequencing logic. Technically the device is a purely static CMOS design operating from a single 3 V to 18 V supply, which allows it to run directly from 5 V, 9 V or 12 V rails without level translation. Because it is a presettable counter with parallel load and carry logic, it can be used as a modulus divider, a programmable delay generator, a bidirectional event counter or the sequencing core of a stepper-motor indexer. Typical applications include industrial sequence and batch counters, frequency dividers and rate meters in test and measurement equipment, digital timers and clock-generation blocks, stepper-motor position indexing, and general digital control logic in equipment built around the CD4000 series. When designing with the CD4029BE, always tie every unused preset input to a defined logic level and place a 100 nF ceramic decoupling capacitor close to the supply pins. If the clock source can overshoot or ring, clamp it or add a small series resistor, because a CMOS clock input driven above the supply rail can latch the device into a static state. This page brings together manufacturer specifications, price and availability context, drop-in alternatives from the CD4000 family, comparison tables and practical design notes so that engineers can evaluate the CD4029BE against equivalent counter ICs before committing to a layout or a bill of materials.
CD4029BEX - 4-Bit Binary/BCD Up/Down Counter, 16-PDIP | Texas Instruments
The Texas Instruments CD4029BEX is a 4-bit presettable binary or BCD-decade up/down counter in the CMOS CD4000 series, packaged in a 16-pin PDIP (EX) through-hole package. It offers a single positive-edge clock input, look-ahead carry in both counting modes, four individual JAM inputs, a PRE-SET ENABLE input, and five outputs consisting of Q1 through Q4 plus a CARRY OUT signal. A counter integrated circuit is a digital logic device that accumulates clock events and presents the running total as a binary-weighted output word. A binary counter advances one count per clock edge with each output toggling at a different power of two, while a BCD-decade counter advances through the ten states 0 to 9, which is the format required by most seven-segment displays. Up/down counters add a direction control so the same silicon can count toward a preset limit or count down from it. In the power-management and digital-control hierarchy, the CD4029BEX sits in the logic IC family, specifically the counters and dividers class of CMOS integrated circuits. The standout feature of this part is the parallel JAM architecture: each of the four jam inputs can asynchronously force its corresponding Q output high or low, independent of the clock, which allows an external controller to load a starting value or capture a count instantly. Look-ahead carry means the CARRY OUT signal is generated in advance of the clock edge, so cascaded counters can be chained without ripple delay. The BINARY/DECADE select pin switches the counting base in one part, and the UP/DOWN pin sets the counting direction, giving a single package both divide-by-16 binary and divide-by-10 decade behavior. Internally the CD4029BEX is a static CMOS design with complementary MOS inputs, so all inputs may be driven from either CMOS or TTL levels as long as voltage thresholds are respected. The single clock line means there is no separate preset clock, which simplifies synchronisation to one system clock domain and prevents race conditions between a preset pulse and a clock edge that separate clocked counters exhibit. Because the outputs are flip-flop based rather than purely combinational, the Q outputs change only on the active clock edge, giving clean, glitch-free output transitions for display and datapath use. Typical applications include divide-by-16 and divide-by-10 frequency dividers, decade counters driving seven-segment LED displays, programmable timing and sequencing modules, batch and piece counting in industrial machinery, position counting in stepper motor indexers, and general ripple-counter chains in legacy control logic. The BCD-decade mode is especially useful for direct display interfacing without a binary-to-BCD conversion stage. When designing around the CD4029BEX, tie all unused CMOS inputs to a defined logic level rather than leaving them floating, because a floating CMOS input can sit in the linear region of the transfer characteristic and draw unpredictable current. Drive JAM inputs from a source that is guaranteed valid whenever the count must be held, and remember that the CARRY OUT pin is an output only, so it must not be used as a clock enable by driving it. Use the PRE-SET ENABLE pin rather than toggling JAM pins asynchronously if the design needs a repeatable, glitch-free load of the starting count. This page combines the manufacturer pin description and function outline, package details, available supply and lifecycle information, and structured drop-in alternatives with practical design notes so engineers can qualify a replacement quickly instead of searching manually through generic cross-reference tables.
CD4029BK - 4-Bit Binary Up/Down Counter | Harris
The Harris Corporation CD4029BK is a 4-bit CMOS binary up/down counter with a preset function, positive-edge triggering, and a 16-CFP package. It is designed for digital counting and control systems where a single counter must advance in either direction, respond to a load preset, and provide a compact logic implementation. The manufacturer listing identifies the device as a binary counter with one 4-bit counting element. A CMOS binary counter is a synchronous state-machine device in the broader logic IC and counter hierarchy. It advances an internal binary state on each active clock transition, allowing a digital system to track events, positions, cycles, or signed movement. The CD4029 family supports both up-counting and down-counting, which distinguishes it from a basic unidirectional binary counter and makes it useful for bidirectional sequencing tasks. The CD4029BK combines a 4-bit counting element with positive-edge clock operation and a parallel preset capability. Positive-edge operation makes the count advance on the designated clock transition rather than on a level change, helping prevent multiple counts when the clock remains stable. Presetting allows the counter to begin at a defined state, which supports repeatable batch sequencing and initialization at a nonzero starting count. The 16-CFP package provides a temperature-resistant ceramic implementation intended for applications where package construction, operating range, or long-term availability matters. Because a replacement must match the footprint, pin assignments, logic levels, timing behavior, and electrical operating limits, engineers should compare a candidate against the manufacturer datasheet before approving a substitution. Counter timing also depends on propagation delay and clock requirements, not merely on the counter resolution. Typical uses include industrial sequence controllers, test equipment, digital instrumentation, batch counters, and bidirectional position-counting systems. In a motor or motion-control system, the counter can track incremental steps in either direction; in test equipment, it can organize measurements into repeatable groups; and in laboratory counters, it can step through preset sequences. For a robust design, use the manufacturer pin-description table to connect clock, load, preset data, count outputs, and supply pins. Confirm reset behavior, valid logic thresholds, maximum clock frequency, and power requirements against the operating conditions. This page combines the manufacturer listing, catalog cross-reference information, drop-in assessment, and practical selection guidance to support engineering review.
CD4029BK3 - 4-Bit CMOS Up/Down Counter | Texas Instruments
The Texas Instruments CD4029BK3 is a 4-bit synchronous, positive-edge-triggered CMOS binary counter with bidirectional counting, available in a 16-lead DFP package. It operates from 5 V to 18 V, supports temperatures from -55°C to 125°C, and has a listed maximum frequency of 2 MHz. The counter provides separate preset and load inputs for loading an initial count and for parallel data entry. A CMOS up/down counter is a sequential logic device that increments or decrements its four-bit output on each active clock edge. The direction of counting is selected by a dedicated up/down control, allowing the same counter to count upward, count downward, or stop when the direction input is held in the inactive state. Within the broader electronics hierarchy, the CD4029BK3 belongs to the CMOS 4000 Series of counters, dividers, and arithmetic logic functions. Key characteristics include four binary counter outputs, preset capability for parallel loading, and operation across a wide 5 V to 18 V supply range. Its positive-edge-triggered architecture makes the counting action occur in response to a rising clock transition. The wide operating-temperature range makes the device suitable for industrial, instrumentation, telecommunications, and legacy control systems where extended environmental capability is required. The CD4029BK3 operates from the original CD4000 CMOS logic family, whose design uses complementary MOSFET stages rather than bipolar transistor logic. CMOS counters can provide low static power consumption, high noise immunity, and broad supply-voltage operation compared with earlier fixed-voltage TTL implementations. These properties make the device useful when counting events must remain reliable across varying supply conditions or noisy industrial environments. Typical uses include programmable sequencing, timing and event-counting systems, frequency division, industrial control logic, laboratory instrumentation, and test equipment. The four counter outputs can be decoded into a larger sequence of control states, while the preset and load functions allow a system to start from a programmed value or acquire a parallel-loaded count. When designing around the CD4029BK3, verify the truth table for the direction, clock, preset, and load controls before connecting external logic. Account for supply decoupling and the propagation delay of the CMOS logic path when determining the maximum usable counting rate in a particular system. Use the manufacturer's pin-description table to assign board traces because the DFP lead assignment must follow the exact package drawing. This page organizes the device specifications, functional characteristics, sourcing information, compatible-product references, and practical design guidance into one engineering-focused reference. It also distinguishes the verified CD4029BK3 data from package and pin details that require confirmation against the manufacturer documentation.
CD4029BM - 4-Bit Binary/Decade Up/Down Counter | TI
Texas Instruments CD4029BM is a CMOS presettable four-stage binary or BCD-decade up/down counter with a 16-pin SOIC package. It operates with positive-edge clocking and provides four individual jam inputs, preset enable, carry-in, carry-out, and four parallel counter outputs. The 16-SOIC package supports conventional surface-mount assembly on standard 0.1-inch lead spacing. A counter is a sequential digital circuit that stores and advances a binary number on each active clock transition. A presettable up/down counter can move toward either a higher or lower count, while binary and BCD-decade modes determine how the four counter bits represent the counted value. This makes the CD4029BM useful within the broader CMOS logic family, logic IC hierarchy, digital counter category, and broader digital semiconductor market. The principal feature is configurable counting behavior. A BINARY/DECADE input selects between binary and BCD-decade operation, while an UP/DOWN input establishes the counting direction. Four JAM inputs allow individual counter stages to be preset, and CARRY-IN provides clock-enable or look-ahead carry functionality. A dedicated CARRY OUT output indicates overflow in the selected counting mode. These controls support programmable event counting, sequence generation, batch counting, and arithmetic-oriented digital logic. The CD4029BM is a four-stage CMOS counter rather than a general-purpose microprocessor or programmable controller. Its clocked operation provides deterministic state transitions, while the parallel outputs expose the current count for decoding, display driving, comparison, or control. Because the device includes look-ahead carry in both counting modes, it can also support cascaded counting arrangements when a higher-resolution count range is required. Typical uses include industrial batch counters, laboratory timer and event-count circuits, digital instrumentation, frequency-division and sequencing logic, automotive and consumer control modules, and teaching or prototyping systems. The logic voltage supply and operating limits should be confirmed against the manufacturer datasheet before using the counter with modern low-voltage peripherals. For reliable implementation, connect the clock and control inputs to compatible CMOS logic levels, use pull-down or pull-up resistors where a control may float, and decouple the supply close to the device. Treat all unused inputs as defined logic states. The JAM and preset paths are especially important to review because incorrect active levels can immediately load or suppress the counter rather than permit normal counting. This page combines the manufacturer function description, package information, pin assignments, drop-in replacement analysis, application guidance, and practical design notes into a single engineering reference. It helps designers identify the correct counting mode, verify package compatibility, plan PCB routing, and evaluate replacement options before committing a design to production.
CD4029BMT - 4-Bit Up/Down Counter | Texas Instruments
The Texas Instruments CD4029BMT is a 4-bit CMOS presettable binary and BCD-decade up/down counter with a positive-edge clock and 16-SOIC package. It supports counting in either direction, preset control, carry input, and separate parallel preset inputs for counter initialization. The device is intended for digital counting, sequencing, timing, and control systems where one counter must operate in both directions. A CMOS counter is a synchronous digital logic device that increments or decrements a binary or BCD-decade state on an active clock edge. The CD4029B belongs to the broader counter and divider logic category, which sits within CMOS logic, digital logic ICs, and general-purpose semiconductor control. Its bidirectional architecture consolidates two counting directions and programmable initialization into one package, reducing the number of separate counter components required by a system. Key features include a 4-bit counting width, selectable binary or decade operation, positive-edge triggering, and separate up/down, binary/decade, preset-enable, and carry-in controls. According to the Texas Instruments product information, it is a versatile CMOS up/down counter designed for digital counting and control applications. The 16-SOIC package also makes it suitable for conventional surface-mount PCB assembly. The counter can represent either a 0-to-15 binary sequence or a 0-to-9 BCD-decade sequence. Preset inputs allow a known starting value to be loaded before counting begins, while the carry and carry-out paths support cascaded stages in larger counters. These functions make the device more adaptable than a simple fixed-direction binary counter. Exact voltage limits, operating-temperature limits, propagation delays, and current ratings require confirmation from the manufacturer datasheet before production release. Typical applications include bidirectional event counters, programmable sequence controllers, industrial timing modules, digital position or motion indicators, test equipment, and control logic that must count toward or away from a preset boundary. Multiple counter stages can also be cascaded when a system requires more than four counting bits. The appropriate selection criteria are logic compatibility, clock requirements, preset behavior, and package availability. PCB implementation should follow the manufacturer pin description and recommended operating rules. Because logic-counter timing depends on clock-edge behavior and propagation delay, route the clock and control traces away from noisy switching nodes, provide a stable supply reference, and account for unused inputs according to the datasheet guidance. Do not infer input states from family naming conventions; use the exact CD4029B datasheet during schematic capture and verification. This product page combines manufacturer-level device identification, verified distributor package and pricing observations, compatible same-family alternatives, parameter comparisons, and practical implementation guidance. It is intended to accelerate initial engineering selection while directing final electrical and pin-level validation to the authoritative CD4029B documentation.
CD4029BPW - 4-Bit CMOS Up/Down Counter | Texas Instruments
Texas Instruments CD4029BPW is a 4-bit CMOS presettable up/down counter IC with a 3 V to 18 V supply range, operation up to 11 MHz, and a 16-pin TSSOP package. It supports both binary counting and decade counting, with the counting direction selected by a logic control input. The positive-edge clock architecture makes the device suitable for digital sequencing, position tracking, industrial control, and programmable timing systems. A counter IC is a member of the broader digital logic hierarchy that includes counters, dividers, registers, and shift registers. The CD4029B family adds reversible counting to that category: a clock pulse advances or reverses the four-bit state, while preset and reset controls allow the counter to be loaded or cleared. Because the device supports both binary and decade modes, one counter can implement modulo-16 binary sequences or decade sequences for timing and sequencing applications. Principal features include four parallel counting outputs, selectable up or down operation, binary or decade counting, preset control, carry output, and positive-edge clocking. Its operating supply range of 3 V to 18 V allows operation across common low-voltage and higher-voltage CMOS logic systems. The listed maximum clock frequency of 11 MHz establishes the operating point for designs requiring medium-speed counting rather than high-frequency timing-chain performance. The CD4029B is implemented as a CMOS logic integrated circuit, allowing operation from a single 3 V to 18 V supply. Its 16-pin TSSOP package supports compact surface-mount assemblies, while the four outputs provide direct state visibility. Designers should account for propagation delay, setup and hold requirements, and the permitted clock transition times when evaluating the maximum operating frequency in a particular system. Typical uses include industrial step and cycle counters, programmable sequence controllers, digital timing modules, phase and position counters, and control systems requiring bidirectional counting. The decade mode can simplify decade-oriented display or sequencing systems, while binary mode supports modulo-16 state machines. The carry output can be monitored by adjacent logic to indicate a count boundary. For PCB implementation, place the clock and control inputs away from high-current switching paths, and use a defined common ground reference. CMOS inputs should not be left floating, and unused inputs should be tied to a defined valid logic level. Power-supply bypassing and signal-integrity review should follow the layout guidance in the manufacturer datasheet. This page organizes the CD4029BPW function, package information, design considerations, commercial information, and validated replacement analysis into one engineering-focused reference. It also distinguishes exact drop-in options from variants that differ in package, pinout, or qualification, helping designers avoid substitution errors before schematic release.
CD4033BD - 5-Bit CMOS Decade Counter | Texas Instruments
Texas Instruments CD4033BD is a CMOS decade counter with five decoded decade outputs, operating from a 5 V supply with a 700 ns propagation delay in a 16-CDIP through-hole package. It is designed for digital counting, frequency division, timing, and display-control applications where a ripple-decade counter is required. A decade counter is a sequential digital-logic component that counts ten states, from zero through nine, and provides decoded outputs for each count. The CD4033BD belongs to the CD4000 CMOS logic family, a subgroup of counter and divider ICs within logic ICs, digital counters, and broader semiconductor products. Its ten decoded output lines allow a display or control system to respond directly to the current count without external binary-to-decimal decoding. Key features include a 5-bit counter section, 16-pin DIP-compatible construction, through-hole mounting, and a stated operating temperature range of -55 °C to 125 °C. The verified product data identifies the CD4033BD as a positive-edge, decade counter with one counter element, a 700 ns propagation delay, and operation from a 5 V supply. The military-temperature grade makes it suitable for equipment requiring an extended temperature range. The CD4033BD is a synchronous CMOS counter with decoded decade outputs. The CLK input advances the count on the positive edge, while the reset and clock-control inputs provide basic sequencing control. Its CMOS architecture supports low-power operation in suitable systems and provides a direct interface to decade-oriented displays, counters, and industrial timing circuits. Typical applications include decade frequency dividers, digital frequency counters, switch-debounce and event-counting systems, display sequencing, industrial panel timers, and embedded timing modules. The decoded Q outputs are especially useful when a design needs ten mutually exclusive output states rather than a binary word. Designers should verify the exact voltage limits, input timing, output-drive capability, and reset behavior against the manufacturer datasheet before using it as a direct substitute in a new circuit. The through-hole package simplifies prototyping and repair, but modern compact products may require a surface-mount counterpart rather than the DIP package. This page consolidates verified distributor pricing, package and timing information, functional application guidance, and pin-level implementation notes so engineers can evaluate the CD4033BD for counter and decade-decoder designs without relying on a single product listing.
CD4033BE - Decoded CMOS Decade Counter | Texas Instruments
The Texas Instruments CD4033BE is a CMOS decade counter/divider with decoded 7-segment display outputs, ripple blanking, and lamp-test functions in a 16-pin PDIP package. It combines a 5-stage Johnson decade counter with an output decoder for driving one stage of a numerical display. According to the manufacturer data, its fully static counter operation extends from DC to 6 MHz typically at VPP = 10 V. The part uses a positive-edge clock and provides a 5-bit counter with decoded display outputs, making it suitable for low-power display and counting systems. A decade counter is a sequential logic device that advances through ten states and then returns to zero. The CD4033BE belongs to the CMOS logic family, whose low static power and broad supply-voltage operating capability are useful in battery-powered and low-power display equipment. Its decoded outputs reduce the external logic count required to translate counter state into the a-through-g segment signals needed by a common-cathode seven-segment display. The chip therefore combines counter, divider, and display-interface functions in one package. Key features include counter and 7-segment decoding in one package, easy interfacing with common seven-segment display types, fully static counter operation from DC to 6 MHz typically at VPP = 10 V, and low-power operation suited to display equipment. A display-enable output provides control over the decoded segment outputs. Ripple blanking is intended to suppress undesirable display transitions, while the lamp-test function supports display testing. These features reduce external component count and simplify compact counter modules. Technically, the device uses a 5-stage Johnson counter followed by a decoder that converts the counter state into seven segment outputs. The decoded interface is designed for one numerical display stage, so a multidigit display generally requires additional counters and appropriate inter-digit blanking arrangements. The manufacturer identifies the device as a CMOS decade counter/divider, and distributor listings describe it as a one-element, 5-bit, positive-edge counter. Detailed operating-voltage limits, output-drive ratings, input leakage, and timing tolerances were not included in the supplied source data and therefore require confirmation in the manufacturer datasheet. Typical uses include standalone decimal counters, laboratory timing references, educational counter trainers, appliance control panels, pulse-counting displays, and compact digital instruments. In a pulse-counter display, the CLOCK input receives the event signal, RESET returns the count to zero, and the decoded outputs drive the segment driver stage. The integrated lamp-test and ripple-blanking functions are particularly useful when operators need to identify failed display segments or avoid visible flicker during counting transitions. When laying out a CD4033BE circuit, account for CMOS input behavior, unused-input handling, supply decoupling, and display-current limits. Because the supplied evidence does not provide complete electrical tables or a verified pin-by-pin diagram, engineers should confirm pin connectivity, maximum supply voltage, output current, clock edge behavior, and timing limits against the official Texas Instruments CD4033B documentation before fabrication. This page consolidates the verified manufacturer description, distributor identification, pricing reference, package information, application guidance, and drop-in-replacement constraints for CD4033BE. It also distinguishes documented characteristics from parameters that still require direct datasheet confirmation, avoiding unsupported precision where the retrieved data is incomplete.
CD4033BF - 5-Bit CMOS Decade Counter, 3-18V, 16MHz, CDIP-16 | TI
The Texas Instruments CD4033BF is a hermetically sealed, ceramic CDIP-16 CMOS decade counter with display-driver outputs, operating over a 3 V to 18 V supply range with a maximum clock frequency of 16 MHz. The device counts on the falling edge of the clock input and provides five decoded output bits (Q0 through Q4) plus a carry output, making it a direct fit for modulo-10, modulo-5 and modulo-2 counting, frequency division and decade display driving. A decade counter is a sequential digital circuit that advances its count once per clock cycle and produces one decoded output line per count state. In the CD4000 CMOS logic family, such counters sit between basic logic gates and higher-level programmable controllers: they divide a clock, sequence events, and directly drive multiplexed or discrete decimal displays without an intermediate binary-to-decimal decoder. Key features of the CD4033BF include the wide 3 V to 18 V single-supply operating range, a 16 MHz maximum input clock rate, five open-drain style decoded outputs that can sink display current directly, and a carry output that indicates the terminal count of ten. The hermetically sealed ceramic CDIP-16 package provides military and industrial temperature robustness with excellent moisture resistance for long-life counter and timing applications. The CD4033BF belongs to the CD4000B, CD14000B and CD40000B CMOS series, the classic high-noise-immunity and wide-supply logic family. Its static and dynamic characteristics are specified across the full 3 V to 18 V range, so one part can serve 5 V, 9 V, 12 V or 15 V systems. The B suffix denotes the buffered, temperature- and voltage-rated performance grade of the series, and the F suffix identifies the hermetic ceramic DIP-16 package option. Typical applications include decade and stepper motor position counters, frequency dividers and time-base generators, industrial batch and piece-counting systems, test equipment cycle counters, and display driver stages for LED or seven-segment decimal readouts where the five decoded outputs are used directly. When designing with the CD4033BF, tie the unused package pins to a defined potential, decouple the supply close to pin 16 with a 0.1 uF ceramic capacitor, and note that the decoded outputs are meant to sink current into display segments rather than drive source current, so pull-up resistors or a segment driver arrangement may be required. This page consolidates device specifications, drop-in sourcing options, package details and practical layout guidance for engineers evaluating the CD4033BF in new or legacy counter and display designs.
CD4033BPW - 4-Bit Decade Counter | Texas Instruments | Displays
Texas Instruments CD4033BPW is a CMOS decade counter and divider with decoded seven-segment display outputs and ripple blanking, packaged in a 16-pin TSSOP (PW). The device provides one five-bit counter element with a positive-edge clock, four decoded display outputs, and a single-digit counting range suited to compact numeric displays. A CMOS decade counter is a synchronous digital logic component that advances through ten states and then repeats. The CD4033B family combines a five-stage Johnson counter with decoding circuitry that produces four segment outputs for one display digit. By integrating the counter and display decoder, the CD4033BPW reduces the logic count required around a common-cathode seven-segment display while supporting ripple blanking between adjacent digits. The primary functional characteristics are a five-bit decade counter, positive-edge triggering, four decoded segment outputs, and a 16-pin TSSOP package. Its decoded outputs are intended for common-cathode seven-segment displays. This makes the device useful in instruments, panel meters, appliance interfaces, counters, timers, and other systems that need compact decimal counting without a microcontroller performing each display update. The counter advances on the rising edge of its clock input and can be initialized through its reset function. The Johnson-counter architecture and integrated decoder organize the counting sequence before presenting segment information to the display. Ripple blanking reduces the visible interaction between successive digits in a multidigit arrangement, although the external display, current-limiting, and blanking implementation must be designed for the intended digit count and drive configuration. The CD4033BPW is suited to laboratory counters, digital timers, household appliances, industrial panel indicators, and low-component-count display systems. Its principal advantage over a software-driven approach is local, hardware-based state management: the clock and decoded outputs can continue operating independently of a main processor. Its main trade-off is the limited four-output interface, which suits displays using one shared segment set rather than independently multiplexed high-digit-count displays. For reliable operation, follow the manufacturer pin-description table when assigning PCB tracks, provide the specified supply voltage and common ground, and use the recommended input decoupling. Keep display-routing and counter-clock traces away from high-current switching paths. Confirm the display polarity and segment mapping before layout because the decoded outputs are designed for a common-cathode seven-segment arrangement. This page organizes the manufacturer device information, order-code compatibility, comparison parameters, and practical implementation guidance for engineers evaluating the CD4033BPW for decimal display and counting designs. It also distinguishes electrically identical order codes from changes that require different package or sourcing considerations.
CD4040BCM - 12-Bit CMOS Binary Counter | onsemi
The onsemi CD4040BCM is a 12-stage CMOS ripple-carry binary counter and divider with one counter element, housed in a 16-pin SOIC package. The circuit advances its count on each negative transition of the input clock and provides 12 binary counter stages for frequency division, timing, and sequential control applications. A binary counter is a sequential digital-logic circuit that records the number of clock transitions applied to it. The CD4040 belongs to the CMOS CD4000 logic family, which extends from counters and dividers into the broader hierarchy of CMOS logic ICs, digital semiconductors, and integrated circuits. Each of the 12 stages divides the preceding clock by two, allowing the component to support a chain of selectable frequency divisions. The principal features of the CD4040BCM are its 12-stage counter organization, negative-edge clock triggering, binary counter/divider function, and reset control. It is suitable when a design needs multiple divide ratios without using a programmable microcontroller. The 16-SOIC package also supports compact conventional PCB assembly while exposing the counter outputs, clock input, and reset control through the device pins. Operationally, the CD4040BCM uses master-slave flip-flop stages arranged as a ripple-carry counter. The count advances when the clock changes from a high level to a low level. A high level at the reset control returns the counter to its all-zero state. Because the stages are ripple based, propagation delay accumulates through the chain, so the maximum clock rate and output timing should be evaluated in the context of the longest division path used in the application. Typical uses include digital frequency division, timing generation, pulse counting, programmable timing interfaces, oscillator and clock-conditioning circuits, and small control systems that need binary state sequencing. The negative-edge trigger also allows the counter to be synchronized carefully with other clocked logic when reset timing and edge relationships are controlled. PCB design should reserve the pins for power, clock, reset, and all 12 counter outputs according to the manufacturer pin-description table. Keep the clock trace short and route it away from noisy switching nodes. If reset is driven by another circuit, constrain it so that power-up behavior and counter initialization remain deterministic. This page combines the device's core counter characteristics, package information, application guidance, comparison points, and replacement considerations. It is intended to help engineers determine whether the CD4040BCM matches a required CMOS counter architecture and to plan a qualification review before using an alternate part on an existing board.
CD4040BCN - 12-Stage CMOS Binary Counter | onsemi
The onsemi CD4040BCN is a 12-stage ripple-carry binary counter and divider in a 16-lead plastic dual-in-line package. It advances one count on the negative transition of each clock pulse, provides 12 binary output stages, and includes an asynchronous master reset for clearing the counter. The device is suitable for frequency division, event counting, timing generation, and digital state-sequence implementations. A ripple-carry binary counter is a digital logic IC that divides an input clock by a power of two at selected binary outputs. The CD4040BCN belongs to the CMOS 4000-series logic hierarchy, combining counter and divider functions in one integrated circuit. Its ripple architecture propagates carry transitions through successive stages, making it appropriate when moderate clocking performance and useful division ratios are more important than synchronous high-speed operation. The principal functional features are 12 independently accessible binary outputs, negative-edge clock advancement, and an asynchronous master reset. Its 16-PDIP construction supports through-hole assembly and prototyping systems. The manufacturer documentation also identifies the CD4020BC and CD4060BC as related 14-stage ripple-carry counters, while CD4040BCN is specifically the 12-stage member. Because each counter stage divides the preceding frequency by two, the output waveform frequencies are derived directly from the clock frequency. The upper outputs therefore provide division ratios through 2^12, subject to the timing limitations of ripple propagation. This architecture is useful for creating lower-frequency clocks, timing intervals, selectable frequency outputs, and basic digital counters without a programmable microcontroller. Typical uses include industrial pulse and event counting, laboratory timer modules, clock-frequency dividers, automotive and appliance timing logic, embedded control interfaces, and educational digital-logic systems. The reset input allows the counter state to be initialized synchronously with the rest of a system. In a divider arrangement, a defined reset level establishes a repeatable starting state before counting resumes. PCB design should preserve the 16-PDIP footprint and route the clock away from sensitive analog or high-speed signal paths. Because ripple-carry transitions can contain accumulated delay across multiple stages, use the lowest-frequency suitable output when precise timing relationships are important. Confirm the actual operating voltage, current, temperature limits, and logic thresholds against the manufacturer datasheet before finalizing a design. This product page combines the 12-stage counter description, verified package information, replacement guidance, parameter comparisons, and practical design considerations. It is intended to support component selection, PCB compatibility checks, timing design, and sourcing decisions for engineers working with the CD4000 CMOS logic family.
CD4040BD3 - 12-Bit CMOS Counter | Texas Instruments | Logic
Texas Instruments CD4040BD3 is a 12-bit ripple-carry binary counter and divider with a 3 V to 18 V supply range, negative-edge clock triggering, and a 24 MHz maximum count rate. The device is packaged in a 16-pin CDIP package and is specified for temperatures from -55 °C to +125 °C. It provides 12 binary outputs for division, event counting, timing, and frequency division in CMOS logic systems. A binary counter is a sequential logic device that increments its internal count when triggered by an active clock edge. The CD4040 family belongs to the CD4000 CMOS logic series, combining binary counter and frequency-divider functions in one package. Its 12 output stages can divide an input clock by binary-weighted ratios from 2 through 4096, allowing useful clock-rate reduction without arranging multiple separate divider packages. The principal operating characteristics are a 3 V to 18 V supply, negative-edge triggering, and a maximum count rate of 24 MHz. The wide supply range supports operation across common CMOS voltage levels, while the extended -55 °C to +125 °C temperature range suits industrial and temperature-demanding equipment. The counter architecture provides one divide-by-2 output and additional binary-weighted output stages for cascaded timing or sequencing functions. The ripple-carry implementation advances one binary stage per clock transition. Its clock input can therefore be driven from another counter or timing circuit, while the Q0 through Q9 and Q8 through Q11 outputs expose intermediate count states. In a feedback arrangement, a selected output can clock the same device to implement longer divide ratios or repeating intervals. Designers should account for cumulative propagation delay across the cascaded stages when operating near the stated count-rate limit. Typical applications include digital frequency division, pulse and event counting, programmable timers, industrial sequencers, clock-period generation, and repetitive pulse-rate measurement. The device is particularly useful when a system needs multiple related divide ratios from one clock or when a binary count must be observed directly by downstream logic. For reliable implementation, follow the manufacturer datasheet for the reset, set, clock, supply, and unused-pin connections. Keep clock traces short and decouple the supply close to the device, because long feedback paths and switching edges can increase transition-time errors in a ripple-counter design. This page combines the device architecture, operating limits, verified source listings, practical application guidance, and same-footprint replacement information to support component selection and PCB-level design decisions.
CD4040BE 12-Stage CMOS Counter | Texas Instruments
The Texas Instruments CD4040BE is a CMOS 12-stage ripple-carry binary counter and divider with one counting element, 12 binary output stages, negative-edge clock triggering, and a 16-pin PDIP package. According to the manufacturer datasheet, the device advances one count on each negative transition of the input clock, while a high level on the RESET input returns the counter to its zero state. A binary counter is a sequential digital circuit that stores or tracks a number as a binary bit pattern. Its operating position in the digital-logic hierarchy is counter IC, digital logic IC, and ultimately semiconductor. The CD4040BE belongs to the CMOS 4000-series family and combines clocked master-slave stages with a reset function. Its 12 stages allow division of the input clock by powers of two from 2 through 4096 when the corresponding output is used as a clock source. The main engineering features are the 12-stage counting architecture, binary counter and divider capability, negative-edge counting, and a high-level reset input. Each output exposes a different power-of-two division stage, allowing one clock source to serve several timing domains. Because the implementation is ripple-carry, propagation accumulates through the internal flip-flop stages, so maximum operating frequency and the usable timing margin depend on the number of enabled stages. The master-slave stage arrangement gives the counter stable outputs under the specified clocking conditions. The RESET function provides a defined initialization state for counters used as dividers, programmable timers, and sequential digital systems. With a 16-pin PDIP package, the CD4040BE is intended for through-hole assembly and is suitable for prototypes, legacy industrial equipment, timing controllers, and educational logic systems. Typical uses include binary event counting, frequency division, pulse-train generation, programmable timing references, and sequential control logic. The device is particularly useful when multiple divide ratios are required from one clock input. In digital systems, selected outputs can produce clocks at 1/2 through 1/4096 of the input frequency, while the RESET input can synchronize the counter with the rest of the system. For a new design, verify clock-edge polarity, reset timing, supply-voltage limits, and maximum operating frequency against the manufacturer datasheet before assigning outputs. Keep clock and reset traces away from noisy switching nodes, provide the required bypassing close to the supply pins, and use unused counter outputs only according to the device's specified logic states. The DIP outline offers generous spacing for hand assembly and through-hole prototyping. This product page combines the CD4040BE architecture, package details, pin assignments, sourcing guidance, replacement analysis, and practical circuit-planning notes to support faster engineering decisions beyond a basic distributor specification listing.
CD4040BM - 12-Bit CMOS Binary Counter | Texas Instruments
Texas Instruments CD4040BM is a CMOS 12-stage ripple-carry binary counter and divider with 12 output stages, negative-edge triggering, and a 16-pin SOIC package. It provides one binary counter element, 3 V to 18 V operation, and operation up to 24 MHz, making it suitable for frequency division, timing generation, and sequential digital control. A binary counter is a sequential logic circuit that records the number of applied clock events and presents that count through digital outputs. A ripple-carry counter advances through its stages sequentially, while a divider derives a lower-frequency clock by selecting a corresponding output stage. Within the broader logic hierarchy, the CD4040BM belongs to the CMOS counter family, falls under counter and divider logic, and ultimately operates as a general-purpose digital semiconductor. The CD4040BM combines a 12-bit counting section with a separate clock input and an asynchronous master reset. Its negative-edge counting behavior means the displayed count changes when the active clock transitions from high to low. The device is designed for a 3 V to 18 V supply, allowing operation from conventional 5 V systems through higher-voltage industrial interfaces. Its 24 MHz maximum operating frequency provides useful timing margin for divide-by-2 through divide-by-4096 clock-generation systems. Ripple-carry implementation favors a straightforward architecture with 12 available count outputs. At lower division ratios, the delay between adjacent stages can affect timing, so designers should account for cumulative propagation delay when driving multiple clocks from the outputs. The clock inputs also provide a choice between the main clock terminal and an independent clock-input terminal for common counter configurations. An active-high master reset clears the count for initialization and repeatable sequencing. Typical applications include programmable timers, digital frequency dividers, pulse and delay generation, industrial sequence controllers, and laboratory test equipment. The 12 output stages can divide a periodic input by powers of two, making the part especially useful when a clean, integer-ratio clock is required. The 16-SOIC package supports conventional surface-mount assembly while providing enough pins for the count outputs, supply rails, clock sources, and reset control. When laying out a circuit, place the reset and clock traces away from the Q0 through Q11 output nets, provide a stable local supply connection, and maintain compatible logic levels between the driver and counter. Designers should check maximum clock frequency at the actual supply voltage because operating speed and supply voltage are related. The counter should also be reset before enabling a new counting sequence when deterministic starting state is required. This product page consolidates the manufacturer identification, package information, operating limits, functional characteristics, application guidance, cross-reference findings, and practical design considerations into an engineering-focused selection resource for counters and dividers.
CD4045BE - 21-Stage CMOS Counter | Texas Instruments
Texas Instruments CD4045BE is a CMOS 21-stage counter built from 21 flip-flop counting stages, two output-shaping flip-flops, and two inverter output drivers. The device operates from 3 V to 18 V, supports operation to 30 MHz, and is packaged in a 16-pin PDIP. It is intended for frequency division, waveform shaping, crystal-controlled timing, and other digital counting applications. A CMOS counter is a sequential logic device that records the number and sequence of input-clock transitions. The CD4045 belongs to the broader logic IC hierarchy: counter -> sequential logic -> digital logic -> integrated circuit. Its 21 internal stages permit division of an input frequency by large powers of two, while separate output-shaping circuitry produces a predictable waveform with a stated 3.125% duty cycle. The principal features include 21 counting stages, a 3 V to 18 V supply range, operation up to 30 MHz, negative-edge counting, and push-pull outputs from the inverter drivers. According to the manufacturer product information, the CD4045B family is 100% tested for quiescent current at 20 V with 5 V, 10 V, and 15 V parametric ratings. The family also meets the stated JEDEC Tentative Standard No. 13B requirements for B-series CMOS devices. The architecture separates the frequency-counting chain from the output-shaping section. Input inverters support oscillator use, while the output-shaping flip-flops and push-pull inverter drivers provide a defined 3.125% output duty cycle. This combination makes the device more specialized than a conventional binary ripple counter: it combines division, waveform shaping, and output drive in one timing circuit. Typical uses include digital frequency dividers, clock-generation and crystal-oscillator circuits, programmable timing modules, pulse-generation systems, industrial counters, and battery-powered digital equipment. Its CMOS implementation is particularly appropriate where low static dissipation is valuable, while the 3 V to 18 V supply range supports multiple legacy logic voltage rails. When designing around the CD4045BE, account for the 16-pin PDIP footprint, the 21-stage division capability, and the output-shaping function rather than treating it as a conventional 16-bit counter. Follow the manufacturer's pin-description and timing diagrams when assigning output stages, and provide appropriate bypass capacitance and a clean clock source to avoid counting errors or unstable oscillator operation. This page organizes the CD4045BE specifications, sourcing information, replacement constraints, application guidance, and practical design considerations in one place. It also distinguishes true same-footprint replacements from logic devices that are only functionally similar, helping engineers select parts without confusing division capability, output duty-cycle behavior, package fit, and supply-voltage requirements.
CD4045BEX - 21-Stage CMOS Counter | Harris Corporation
Harris Corporation CD4045BEX is a CMOS 21-stage binary counter with output-shaping flip-flops, inverter output drivers, and input inverters, supplied in a 16-pin plastic dual in-line package. The counter contains 21 counting stages and uses two flip-flops to shape its output waveform to a 3.125% duty cycle. Push-pull operation is provided by the inverter output drivers, while the input inverters support use in crystal-oscillator and timer arrangements. A CMOS counter is a synchronous or asynchronous digital logic circuit that divides an input frequency into lower-frequency outputs by advancing through binary states. The CD4045B belongs to the 4000-series CMOS logic family, within the broader hierarchy of logic ICs, digital semiconductors, and integrated circuits. Its primary roles are frequency division, timing, waveform shaping, and low-power digital sequence generation. The architecture provides 21 counter stages for high division ratios, two output-shaping flip-flops, two inverter output drivers, and input inverters. The shaped output supports a 3.125% duty cycle, making the device useful when a narrow pulse or clock-like waveform is required. The manufacturer’s CD4045B information identifies parametric testing at 5 V, 10 V, 15 V, and 20 V, indicating operation across multiple supply conditions. Push-pull output drivers provide a defined output configuration for driving downstream digital circuitry. Compared with open-drain implementations, this arrangement can simplify clock-chain design by avoiding an external pull-up resistor. The high division count also allows a single input clock to generate a substantially lower-frequency output without arranging a long chain of separate counter packages. Typical uses include crystal-based timekeeping, programmable timer and delay circuits, industrial pulse-generation systems, frequency dividers, and low-power digital instrumentation. Battery-operated equipment is another relevant application area because the CD4000B family was designed for digital equipment requiring low dissipation or battery operation. Its counter stages can establish long timing intervals when driven from a stable frequency source. When laying out a CD4045BEX circuit, use the manufacturer pin-description table to assign every connection and place any required clock, reset, and output components close to their associated pins. Pay particular attention to unused inputs and supply decoupling. The CMOS counter can support long timing intervals, but output jitter, clock rise time, reset behavior, and power-supply noise ultimately determine the accuracy of the resulting time interval. This product page combines the counter architecture, verified manufacturer descriptions, packaging information, drop-in alternatives, parameter comparisons, and practical implementation guidance. It is designed to help engineers identify the correct Harris variant, understand the 21-stage divider behavior, and plan a PCB or legacy-system replacement without overlooking pin compatibility or output-waveform requirements.
CD4045BF - 21-Stage CMOS Counter | Texas Instruments
Texas Instruments CD4045BF is a CMOS binary counter IC with one 21-bit counter element, negative-edge clock operation, and a 16-CDIP package. The counter is designed for digital equipment requiring low dissipation or battery-powered operation, and the Texas Instruments product page states that quiescent current is tested at 20 V with 5 V, 10 V, and 15 V parametric ratings. A counter is a sequential digital circuit that stores and advances a binary count when a clock edge occurs. The CD4045BF belongs to the CMOS logic hierarchy, combining counter, divider, frequency-measurement, and timing functions in one integrated circuit. Its 21-stage architecture allows a clock input to be divided into lower-frequency signals, making it useful when a system needs repeatable counting without a microcontroller or discrete flip-flop chain. The CD4045BF uses negative-edge clock triggering, so the counter advances on the transition toward the low state of the clock input. A clock-inhibit input provides an external way to prevent counting, while a master-reset path supports initialization of the counter state. Because these functions are implemented in CMOS, the device is particularly appropriate for low-power digital systems, including portable instrumentation and battery-operated control equipment. The 16-CDIP construction provides a through-hole package for conventional PCB assembly. Its staggered, relatively long leads support hand insertion and leaded through-hole processes where a surface-mount package would be unsuitable. Circuit layout should reserve adequate clearance around the package and route the clock and inhibit signals away from sensitive analog sections to reduce unintended coupling. Typical uses include divide-by-N clock generation, event and pulse counting, time-interval measurement, periodic digital sequencing, and low-power timing systems. The 21-stage count range allows one input clock to represent a substantially longer interval than the input frequency alone, while the external reset and inhibit controls let a controller coordinate measurement or disable the count during critical periods. Design the surrounding circuit around the CD4045BF's CMOS supply requirements and verify operating limits against the manufacturer datasheet. Keep the clock waveform clean, use a suitable reset strategy for the target logic state, and do not assume that the inhibit input can substitute for reset. These practices reduce the risk of metastability, unintended counting, or inconsistent startup behavior. This product page consolidates the exact device identity, package information, technical specifications, source links, practical applications, and verified drop-in alternatives. It also highlights design considerations that help engineers evaluate clocking, reset sequencing, power behavior, and PCB implementation before placing CD4045BF into a new or legacy design.
CD4045BPW - 21-Stage CMOS Counter | Texas Instruments
Texas Instruments CD4045BPW is a CMOS timing circuit containing 21 counter stages, two output-shaping flip-flops, two inverter output drivers, and input inverters for crystal-oscillator use. It operates from the 5 V, 10 V, and 15 V parametric families, with testing performed at 20 V, and is packaged in a 16-pin TSSOP measuring approximately 0.173 inch wide by 4.40 mm. The circuit combines a long division chain with waveform-shaping logic for applications requiring stable, predictable timing. A CMOS counter is a sequential digital-logic circuit that divides an input frequency through one or more binary stages. The CD4045B belongs to the 4000-series CMOS counter family and combines that counter function with oscillator-support circuitry. Its architecture makes it useful when a design needs both a divide-by-2^21 counting path and a separately shaped output rather than a simple standalone binary counter. The primary features include 21 flip-flop counting stages, two flip-flops for shaping the output waveform, and push-pull operation from the inverter output drivers. The shaped output is specified for a 3.125% duty cycle. The manufacturer also states that every device is 100% tested for quiescent current at 20 V under 5 V, 10 V, and 15 V parametric ratings, providing production control for this timing function. Technically, the CD4045B supports use in a crystal oscillator through its input inverters. When the counter stages are configured for division, the output-shaping flip-flops generate a stable waveform with the specified duty-cycle behavior, while the complementary inverter drivers provide push-pull output drive. This integration reduces the number of external logic blocks required for long-divide timing systems. Typical uses include crystal-based timebase circuits, digital timers, programmable counters, frequency dividers, and embedded control systems that require a long division ratio. Its CMOS construction is particularly relevant to battery-operated digital equipment where low power dissipation and operation from a single supply are important. The exact supply limits, operating temperature range, and timing tolerances should be confirmed in the manufacturer datasheet before production release. PCB design should provide a short, low-impedance supply path and place bypass capacitance close to the device. Keep oscillator and timing traces away from noisy switching nodes, and use the pin-description table in the manufacturer datasheet when assigning tracks. Because the counter contains many sequential stages, unused outputs should not be relied upon as arbitrary logic signals unless their documented operating state is understood. This product page combines the manufacturer's functional description, package information, parametric-rating details, practical circuit guidance, and a structured replacement analysis. It also identifies which electrical and timing fields require confirmation from the CD4045B datasheet before a schematic or layout is approved.
CD4049AE - Hex CMOS Buffer/Converter, 3-18V | Harris
The Harris CD4049AE is a hex inverting/non-inverting CMOS buffer and logic-level converter with a 3 V to 18 V supply operating range, supplied in a 16-pin DIP package. The device provides six independent buffer channels for converting or restoring logic levels and can operate from the same supply used by the associated CMOS logic. According to the manufacturer information referenced by the distributor listing, the CD4049 family is intended for buffering and logic conversion applications. A CMOS buffer or converter is a logic IC that isolates a source from a driven load while providing compatible voltage levels. In the device hierarchy, CD4049AE belongs to the CMOS logic family, with the broader categories of digital logic, integrated circuit, and semiconductor. Its wide supply-voltage range allows use in systems operating from low-voltage 3 V rails through traditional 18 V CMOS rails, although operating points must remain within the limits stated in the manufacturer datasheet. The CD4049AE is described as a hex inverting/non-inverting buffer converter. Its primary advantages are flexible supply-voltage operation and the availability of multiple channels in one package. Because the AE package is a through-hole 16-pin DIP, it is appropriate for legacy industrial equipment, prototypes, repair assemblies, and control systems where surface-mount components would require a different physical footprint. The CD4049 family is frequently considered when a logic signal must drive another circuit with a different input voltage requirement or when a signal source needs buffering. Input and output rise and fall times, propagation delay, output drive current, input leakage, and noise margins must be checked against the actual clock rate, load capacitance, supply voltage, and logic thresholds of the connected devices. The CD4049AE should not automatically be treated as a general-purpose level shifter for every interface. Typical uses include industrial control logic, legacy instrumentation, display and interface control, signal conditioning between CMOS stages, and repair of systems originally designed around the CD4000 family. In these applications, the six buffered channels can reduce loading on sensitive logic outputs while maintaining compatible supply-domain operation. When designing around the CD4049AE, begin with the manufacturer datasheet and confirm the exact pinout, input/output logic behavior, absolute maximum ratings, and timing limits for the relevant revision. Check that every connected signal remains within the permitted input-voltage range, that unused inputs are tied to a defined logic level, and that unused outputs are left unconnected unless the datasheet permits otherwise. Supply bypassing and breadboard or PCB layout quality also matter because long connections and high-impedance nodes can increase noise susceptibility and transition-time distortion. This page combines verified distributor sourcing information, the referenced CD4049 family description, package details, structured engineering guidance, and clearly marked data gaps. It is intended to help engineers identify the CD4049AE quickly while separating confirmed facts from parameters that must be obtained from the official manufacturer datasheet before design release.
CD4049AK - Hex Non-Inverting Buffer, 12V, 16-CFP | Harris
The Harris Corporation CD4049AK is a 12 V hex non-inverting buffer integrated circuit offered in a 16-CFP surface-mount package. The verified distributor listing identifies the device as an active logic buffer/channel element, while the CD4049 family documentation identifies the CD4049 series as a hexadecimal non-inverting buffer. Its 16-CFP package provides a compact surface-mount option for designs requiring buffered CMOS logic rather than a direct gate-to-gate connection. A non-inverting buffer is a digital logic device that reproduces its input at the corresponding output without changing the logical polarity. Within the broader semiconductor hierarchy, the CD4049AK belongs to CMOS logic ICs, specifically the buffer and inverter category. A buffer can add drive strength and isolate a logic stage from downstream loading, provided its voltage, timing, and drive specifications remain acceptable for the intended circuit. The key verified attributes of the CD4049AK are its 12 V supply designation, non-inverting buffer function, hexadecimal organization, 16-CFP surface-mount package, and active lifecycle status. The Harris designation preserves compatibility with established CD4000-series sourcing. Rochester Electronics is the distributor associated with the exact CD4049AK listing on DigiKey, while other verified listings also connect the MPN with Harris and the 16-CFP package. CD4000-series logic is commonly evaluated for industrial control, interface isolation, signal conditioning, and embedded digital systems. The CD4049AK should be selected only after confirming its complete electrical limits, input and output logic levels, propagation delay, output drive, noise margin, and power dissipation from the applicable manufacturer datasheet. The same package outline must also be checked against the PCB land pattern before it is treated as a direct replacement. Typical design roles include buffering digital control signals, driving logic inputs away from a source device, distributing a logic signal to multiple compatible loads, and separating a high-impedance logic node from downstream switching or fanout requirements. In each case, the input must remain within the accepted logic range and the connected load must not exceed verified output-current and capacitance limits. The most important layout consideration is to minimize trace length between the buffer and its driven load while maintaining a stable ground reference. Unused inputs should not be left floating if the manufacturer datasheet specifies a defined state. Supply bypassing, input thresholds, and maximum supply voltage must also be checked before publication of the PCB design. This page consolidates the verified distributor price, stock indication, manufacturer identity, package information, lifecycle state, and available cross-reference findings for CD4049AK. It also distinguishes confirmed drop-in alternatives from unverified or different-package substitutes so engineers can avoid unsupported replacement claims.