Logic ICs
بەرهەمەکان (720+)
CD4522BMT - Programmable BCD Counter | Texas Instruments
Texas Instruments CD4522BMT is a programmable 4-bit BCD divide-by-N counter operating from 3 V to 18 V in a 16-pin SOIC package. It counts downward and provides a decoded zero-detect output for divide-by-N applications. The device is supplied in tape-and-reel packaging for automated manufacturing. A programmable BCD counter is a sequential logic circuit that counts in binary-coded decimal notation and implements a preset division ratio. It belongs to the CMOS counter and divider hierarchy within digital logic ICs. Unlike a simple binary counter with a fixed division ratio, the CD4522BMT accepts programmable parallel inputs, allowing the count threshold to be adjusted for different timing, sequencing, and frequency-division requirements. The primary features are a 4-bit programmable decade counter, downward counting, and a decoded zero-state output. Its operating supply range is 3 V to 18 V, supporting both low-voltage and conventional CMOS supply rails. The manufacturer specifies operation from -55 °C to 125 °C. A 16-lead small-outline package enables compact PCB layouts while providing separate clock, reset, parallel load, and count-control connections. The CD4522BMT uses positive-edge clocking to update the count, allowing an external clock source to control the counter state. The parallel inputs select the divide-by-N threshold when load is asserted. Its zero output is decoded specifically for applications that need to recognize the terminal count, which can simplify trigger generation in timers and programmable dividers. The 3 V minimum supply operation also improves compatibility with modern low-voltage control systems. Typical uses include programmable timer periods, industrial pulse and frequency dividers, sequence counters, digital timing modules, and sequential test equipment. In a divide-by-N circuit, the counter decrements from its programmed terminal value toward zero, and the decoded zero output provides a repeatable endpoint indication. This makes the device useful where a selectable count interval is needed without implementing an entire counter in programmable logic. PCB design should provide a defined clock signal and observe the device’s voltage limits. Because the part can operate across a broad 3 V to 18 V range, the supply voltage, input thresholds, output load, and external timing components must be evaluated together. Decoupling and routing should follow the manufacturer’s recommended application circuit, with the clock and control traces kept short to reduce susceptibility to ringing and unwanted transitions. This product page combines the exact CD4522BMT order information with drop-in-family comparisons, application guidance, pinout location, and design considerations. It is intended to help engineers select the correct package and confirm whether an alternative preserves the 16-pin SOIC footprint and counter function.
CD4522BPW - 4-Bit BCD Divide-by-N Counter | Texas Instruments
The Texas Instruments CD4522BPW is a CMOS programmable BCD divide-by-N counter with one 4-bit counter element, positive and negative count inputs, and a 16-pin TSSOP package. The device is designed for divide-by-N applications and includes a decoded zero-state output. It operates across a manufacturer-rated temperature range of -55°C to +125°C in the PW package. A programmable BCD counter is a digital logic device that counts in binary-coded decimal and divides an input frequency by a selected value from 2 through 10. The CD4522B family belongs to the broader hierarchy of counter logic, sequential logic, logic ICs, and integrated circuits. Its decoded zero output provides a useful indication of the programmed divide-by-N operating cycle, allowing the output to participate in cascaded or synchronized timing systems. The CD4522BPW provides four counter bits, one programmable counter element, and separate positive-edge and negative-edge counting inputs. The manufacturer describes symmetrical output characteristics and specifies a maximum input current of 1 µA at 18 V over the full package-temperature range, with 100 nA at 18 V and 25°C. These characteristics make the device relevant to low-frequency clock division, timing generation, industrial sequence control, and test-equipment logic. The CD4522B series meets JEDEC Standard No. 13B, “Standard Specifications for Description of ‘B’ Series CMOS Devices.” Its CMOS implementation supports operation from digital logic systems while providing BCD counting and programmable division in one compact package. The PW option is supplied in a 16-lead thin shrink small-outline package, making it suitable for compact surface-mount assemblies that require programmable rather than fixed division ratios. Typical uses include dividing a system clock for a display refresh cycle, producing one-shot or periodic timing pulses, sequencing external loads in industrial equipment, and generating a lower-frequency clock for another digital subsystem. The decoded zero output can be used as a load-reset or cycle-completion indication. Designers should account for propagation delay when cascaded counters are used because the division stage and zero-state decode introduce timing between clock edges and decoded outputs. For a new design, place the CD4522BPW close to the clock source and logic loads to minimize clock routing sensitivity. Use a clean, stable clock signal, provide normal CMOS input levels, and account for unused inputs in the selected implementation. Because the package has 16 leads, PCB layout must follow the official PW package drawing and keep copper and routing consistent with the manufacturer pin configuration. This product page combines the manufacturer’s device description, package information, JEDEC qualification detail, drop-in candidate information, and engineering guidance into a focused design reference. It also highlights the practical distinction between the standard PW ordering code and package-qualified variants, helping engineers verify footprint, temperature grade, and sourcing requirements before committing a PCB design.
CD4585BD - 4-Bit Magnitude Comparator | Texas Instruments
The Texas Instruments CD4585BD is a 4-bit CMOS magnitude comparator with eight comparison inputs, three active-high outputs, and three cascading inputs, operating from 3 V to 18 V in a 16-pin CDIP package. It compares two binary or BCD words and indicates whether A is less than, equal to, or greater than B. A magnitude comparator is a combinational logic device that examines corresponding bits of two multi-bit operands and produces an ordering result. The CD4585BD belongs to the CMOS logic family, where CMOS means complementary metal-oxide-semiconductor. Its hierarchy extends from a digital comparator IC to a logic IC, integrated circuit, and semiconductor. The device is useful whenever a system must determine the relationship between two numerical values without relying on a processor. The CD4585BD supports supply voltages from 3 V to 18 V, operates across a military temperature range of -55 °C to +125 °C, and provides a 160 ns propagation delay at 15 V with a 50 pF load. Its active-high A<B, A=B, and A>B outputs report the comparison result directly. The specified 100 µA supply current supports low-power logic designs, while the 6.8 mA output-current figure defines the available output drive in the cited product data. Cascading inputs extend the comparison to more than four bits. The equal, greater-than, and less-than cascade paths allow multiple CD4585 devices to compare two larger words. Designers must connect unused inputs to defined logic levels and account for propagation delay through each cascade stage when evaluating system timing. Typical uses include digital sorting and ranking, address and threshold comparison, BCD arithmetic control, test-equipment decision logic, industrial control sequencing, and embedded systems that require a hardware ordering function. Its military temperature range and through-hole CDIP-16 package also make it suitable for legacy and ruggedized equipment where surface-mount alternatives are unsuitable. For reliable operation, keep every supply pin within the 3 V to 18 V range and use the manufacturer's recommended operating conditions. Decoupling capacitors should be placed close to the supply pins, while all digital inputs should remain driven to valid CMOS levels. Propagation-delay accumulation and output contention require particular attention when several devices are cascaded. This page consolidates the verified distributor specifications, pricing context, a same-family drop-in assessment, and practical implementation guidance. It also separates documented electrical values from unavailable parameters rather than filling gaps with estimated or invented specifications.
CD4585BE - 4-Bit CMOS Magnitude Comparator | TI
The Texas Instruments CD4585BE is a 4-bit CMOS magnitude comparator that compares two 4-bit binary or BCD words and reports whether the first word is less than, equal to, or greater than the second word. It accepts eight comparison inputs, provides three active-high result outputs, and includes three cascading inputs. The device operates from 3 V to 18 V and is supplied in a 16-pin PDIP package, with a specified temperature range of -55 °C to 125 °C. A magnitude comparator is a logic IC within the broader CMOS comparator category. Its purpose is to evaluate the relative magnitude of two multi-bit values and produce a corresponding digital result. The CD4585B supports binary and BCD data, making it useful in computer-control, digital arithmetic, threshold-detection, sorting, and industrial automation systems. Its three cascading inputs allow designers to extend comparisons beyond four bits by connecting multiple devices. The principal features include eight 4-bit comparison inputs, three active-high outputs labeled A<B, A=B, and A>B, and a wide 3 V to 18 V supply range. The wide operating voltage is useful when a system uses a supply above the typical 5 V logic range. The specified -55 °C to 125 °C temperature range provides broad environmental capability, while CMOS operation places the device in the low-power CD4000 logic family. The CD4585B compares each corresponding bit of the two input words and propagates the most significant comparison result toward the lower-order bits. This internal structure produces three mutually related outputs rather than one combined result. Cascading inputs permit a higher-order device to accept the comparison state generated by a lower-order device, enabling comparison of wider binary or BCD values without redesigning the basic logic function. Typical applications include digital counters, threshold and limit detectors, arithmetic control, industrial sequence control, sorting logic, and embedded decision systems. It can compare a measured or represented value against a reference word and indicate whether the value is below, equal to, or above the configured limit. The BCD capability also supports decimal display and control systems where encoded ten-state values are more convenient than binary values. When designing around the CD4585BE, verify unused inputs so that no CMOS input remains floating. Place supply-bypass capacitance close to the device and route output signals away from noisy analog or switching nodes. Because the part is a through-hole PDIP device, it is particularly suitable for prototypes, educational systems, legacy industrial equipment, and new designs that specifically retain a 16-pin through-hole footprint. This page combines manufacturer information, distributor availability, package details, related comparator references, and engineering-oriented comparison data. It also identifies where verified technical values are unavailable so procurement and design decisions can be made without confusing incomplete cross-reference information with a guaranteed drop-in replacement.
CD74AC151M96 - 8-Input Multiplexer, 16-SOIC | Texas Instruments
The Texas Instruments CD74AC151M96 is a high-speed 8-input digital multiplexer fabricated in the AC (Advanced CMOS) logic family, delivered in a 16-pin SOIC (D) surface-mount package with Tape and Reel packing (-96 suffix). It selects one of eight data inputs (D0-D7) under control of three select lines (A, B, C) and drives both a true output (Y) and a complementary output (W), with an active-low enable (G) input that forces both outputs low when asserted. A multiplexer (MUX) is a combinational logic device that routes one of several input signals to a single output line, forming a key element in the hierarchy of digital logic ICs: MUX -> combinational logic -> logic IC -> semiconductor. Multiplexers perform parallel-to-serial conversion, data source selection, and Boolean function generation of up to four variables in a single package. Key features include operation from 1.5V to 5.5V supply per the AC family specification, balanced noise immunity of 30% of the supply voltage, and propagation delays as low as 5.5 ns at 5V - speed comparable to bipolar F, AS, and S logic families with CMOS low static power consumption. Outputs source or sink up to 24 mA, enabling direct drive of substantial fan-out loads. The advanced CMOS process delivers high noise immunity and low quiescent dissipation, with TTL-level input compatibility at 5V operation. Balanced propagation and transition times minimize output skew in high-speed systems. The wide -55C to +125C operating range of this package supports industrial and military-temperature designs. Typical applications include microprocessor data routing, parallel-to-serial converters, Boolean function generators, communication channel selection, and test-equipment signal switching, where the complementary W output eliminates the need for an external inverter. Design tip: properly terminate the enable and select lines to avoid undefined states, and use a pull-up or pull-down resistor on Y/W when the device may be disabled. Account for input capacitance when routing high-speed signals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
CD74AC151QM96Q1 - 8:1 Mux, AEC-Q100 | Texas Instruments
The Texas Instruments CD74AC151QM96Q1 is an automotive-grade (AEC-Q100 qualified) 8-line to 1-line data selector/multiplexer in a 16-pin SOIC (M) package. It belongs to the CD74AC Advanced CMOS logic family, which supports operation from 1.5 V to 5.5 V with balanced noise immunity of 30% of the supply voltage. The device selects one of eight data sources under control of a 3-bit address and provides both true (Y) and complementary (W) outputs with a strobe/enable input. A digital multiplexer is a combinational logic circuit that forwards one of several input signals to a single output line, selected by binary control address inputs. In the logic IC hierarchy, the multiplexer sits under combinational logic > data routing ICs within the broader category of 4000/7400-family digital logic. Multiplexers can also act as Boolean function generators of up to four variables, parallel-to-serial converters, and data source selectors. Key features include 8:1 selection with complementary outputs, high-speed AC-family switching comparable to bipolar F, AS, and S speed classes, operation up to 5.5 V, and balanced CMOS noise immunity. The Q1 suffix denotes AEC-Q100 qualification, making the part suitable for automotive and harsh-environment designs where temperature cycling, ESD robustness, and quality requirements exceed commercial grades. The CD74AC151 uses advanced CMOS technology for low static power consumption combined with fast propagation delays, making it appropriate for address decoding, sensor-source selection, and data-routing in automotive ECUs, industrial control modules, and instrumentation front ends. Typical applications include automotive body and powertrain control modules selecting among sensor channels, parallel-to-serial data conversion in microcontroller-based systems, and universal logic-function generation in FPGA glue logic and test equipment. Design tip: tie the strobe (active-low enable) low for continuous selection, and keep unused data inputs at defined logic levels to prevent floating CMOS inputs that increase supply noise and current.
CD74ACT163 - 4-Bit Sync Binary Counter 5V | Texas Instruments
The Texas Instruments CD74ACT163 is a 4-bit synchronous presettable binary counter with synchronous reset, fabricated in the advanced CMOS (ACT) logic family and housed in a 16-pin SOIC package. It operates from a 5V supply with TTL-voltage-compatible inputs, and features an internal carry look-ahead for high-speed counting designs plus a ripple carry output (RCO) for n-bit cascading. A synchronous binary counter is a sequential logic IC in which all flip-flops are clocked simultaneously by a common clock edge, so all output bits change in coincidence rather than rippling stage to stage. Within the logic IC hierarchy (counter -> sequential logic IC -> digital IC), synchronous counters eliminate the cumulative propagation delays of ripple (asynchronous) counters, enabling reliable high-speed counting and glitch-free decoded outputs. Key features include synchronous counting, synchronous parallel load via the active-low LOAD input for programmable counting, and synchronous reset (CLR) that clears all outputs on the next clock edge, eliminating the decoding spikes inherent in asynchronous clearing. The count-enable inputs (ENP, ENT) permit cascading and gated counting without external gating logic, and the RCO terminal supports direct n-bit cascading. The ACT technology combines CMOS low static power with TTL input thresholds at 5V operation, making the device directly interchangeable in TTL 74163 sockets. Positive-edge clocking and fully synchronous preset, count, and clear functions simplify timing analysis in multi-stage counter chains. Typical applications include frequency division, digital timers, event counting, address generation, industrial sequencing, and cascaded n-bit counters built by wiring RCO of one stage to ENT of the next. Design consideration: because reset and load are synchronous, hold CLR or LOAD low for at least one full clock period; for asynchronous-reset designs use the related CD74ACT161 instead. Decouple the 5V rail with 0.1uF close to the VCC pin. This page synthesizes distributor data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
CD74HC138 - 3-to-8 Line Decoder/Demux 2-6V | Texas Instruments
The Texas Instruments CD74HC138 is a high-speed silicon-gate CMOS 3-to-8 line decoder/demultiplexer with inverting outputs, supplied in a 16-pin package (PDIP, SOIC, and other variants), operating from a 2V to 6V supply with three binary select inputs and eight active-low outputs. According to the TI datasheet SCHS147J, the device is well suited to memory address decoding or data routing applications. A decoder/demultiplexer is a combinational logic device in the broader logic IC family (logic -> decoder -> demultiplexer -> data routing IC). Decoders convert binary-coded inputs into one-hot outputs, while the same circuit used with enables asserted acts as a demultiplexer routing data to one of eight output lines. The CD74HC138 belongs to TI's High Speed CMOS (HC) logic family, offering CMOS low power with LSTTL-comparable speed. Key features include three binary select inputs (A0, A1, A2) with full on-chip decoding, three enable inputs (two active-low, one active-high) supporting cascaded 4-to-16 or larger decoders without external gates, eight active-low outputs suited to memory chip-select (CS) and enable lines, low quiescent CMOS power consumption, and wide 2V to 6V supply operation typical of the HC family. Architecturally, the CD74HC138 uses high-speed silicon-gate CMOS construction with speeds comparable to low-power Schottky TTL logic. When used as a demultiplexer, the active-low enables serve as the data input while the select inputs route the data to the addressed output, eliminating external inverter gates. Typical applications include memory address decoding for SRAM/EPROM/Flash chip selects, I/O port expansion in microprocessor systems, data routing and demultiplexing, and address latching in embedded control systems. Its inverting outputs directly drive active-low memory CS/CE inputs without external inverters. Design tip: tie unused enable inputs to their inactive levels and keep select lines short; for 4-to-16 decoding, cascade two devices using one enable as the MSB select. Verify AC timing at your supply voltage and load. This page synthesizes distributor pricing, drop-in alternatives, cross-reference data, and practical design notes not found in the manufacturer datasheet.
CD74HC374 - Octal D Flip-Flop, 3-State, 2-6V | Texas Instruments
The Texas Instruments CD74HC374 is a high-speed CMOS logic octal positive-edge-triggered D-type flip-flop with 3-state outputs, housed in a 20-pin package (PDIP-20 (N), SOIC-20 (DW), or TSSOP-20 (PW)). It operates from a wide 2V to 6V supply and each output can drive up to 15 LSTTL loads, making it a robust bus-oriented storage element. An octal D-type flip-flop is a sequential logic IC containing eight independent D flip-flops that share a common clock and output-enable control. It belongs to the 74HC (High-speed CMOS) logic family, which combines LSTTL-compatible speed with the low static power consumption of CMOS technology, sitting within the broader hierarchy of digital logic ICs > flip-flops > edge-triggered registers. Key features include positive-edge-triggered data capture on the LOW-to-HIGH clock (CP) transition, 3-state outputs controlled by an active-low output enable (OE) that is independent of register operation, a typical propagation delay of 15 ns at 5V, and a maximum clock frequency of 30 MHz. The silicon-gate CMOS process provides high noise immunity and very low quiescent current compared with bipolar LSTTL equivalents. Architecturally, data present on the D inputs is stored on each rising clock edge, while OE=HIGH forces all Q outputs into a high-impedance state without disturbing the stored register contents. This enables bus multiplexing, shared data buses, and bidirectional data flow in microprocessor and memory systems. The device works in both 3.3V and 5V logic systems thanks to its wide supply range. Typical applications include microprocessor address and data latching, I/O port expansion, bus interfacing, register files, and synchronization stages in DSP and communication interfaces. Designers should keep the clock clean and glitch-free, control OE to avoid bus contention, and place 100 nF decoupling capacitors close to the VCC pin. According to TI datasheet SCHS183A, unused inputs must never be left floating. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.
CD74HC4511M96 - CMOS BCD-to-7-Segment Decoder/Driver SOIC-16 | TI
The Texas Instruments CD74HC4511M96 is a High Speed CMOS Logic BCD-to-7-Segment Latch/Decoder/Driver supplied in a 16-pin SOIC (D) package on tape and reel (M96 suffix). It operates over a 2 V to 6 V VCC range for the HC version, decodes four BCD address inputs (D0-D3) into seven segment outputs (a-g) plus ripple blanking, and integrates input latches, lamp-test (LT), and active-low blanking (BL) control inputs. Per the TI product page, the part delivers 10 mA source current per segment at 6 V on the HC variant, sufficient to directly drive common-cathode LED displays with external current-limiting resistors. A BCD-to-7-segment decoder is a logic IC that converts a 4-bit Binary Coded Decimal input (0-9) into the seven individual segment drive signals (a, b, c, d, e, f, g) needed to display a decimal digit on a 7-segment LED or LCD display. These devices sit in the logic IC hierarchy: decoder/driver -> display driver -> logic IC -> integrated circuit -> semiconductor. They are essential building blocks in numeric displays used in instrumentation, appliance panels, industrial counters, and embedded systems where a microcontroller must drive multi-digit readouts efficiently. Key features of the CD74HC4511M96 include input latches for BCD code storage, allowing data to be held stable while multiplexing multiple digits; lamp-test and blanking capability for testing all segments simultaneously and for PWM-based dimming; balanced propagation delays and transition times; and significant power reduction versus the original CD4000-series CMOS designs. The high-output sourcing capability (10 mA at 6 V) eliminates the need for external segment drivers in most LED display applications. The CD74HC4511M96 uses CMOS technology with CMOS-compatible inputs on the HC variant. Its 16-pin SOIC (D) small-outline surface-mount package measures approximately 9.9 mm x 3.9 mm with a 1.27 mm pin pitch, making it well-suited to compact PCB layouts. The integrated latch enables display multiplexing with no external storage, simplifying firmware and reducing microcontroller pin count when several digits share a data bus. Typical applications include digital panel meters, instrument counters, industrial control readouts, appliance displays (microwave ovens, washing machines), electronic scoreboards, point-of-sale terminals, and any embedded system that needs to display decimal digits on a 7-segment LED or LCD. Designers use it when they need a hardware decoder to offload display refresh from a microcontroller or when supporting multi-digit multiplexing without continuous MCU intervention. When designing with this device, add series resistors between each segment output and the LED anodes to limit current, or use a constant-current driver if brightness uniformity is critical. For multi-digit multiplexing, route BL through a PWM signal or high-frequency oscillator to achieve dimming and ghosting reduction. The LE (Latch Enable) input must be low for transparent operation and high to store the BCD code. The 'M96' suffix indicates tape-and-reel packaging for high-volume assembly. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found on any single distributor listing, giving engineers a one-stop reference for selecting and using the CD74HC4511M96 in new designs and as a drop-in replacement.
CD74HCT165M96 - 8-Bit Parallel-In/Serial-Out Shift Register | TI
The Texas Instruments CD74HCT165M96 is an 8-bit parallel-in/serial-out shift register built on High-Speed CMOS (HCT) logic, housed in a 16-pin SOIC (D) package with a -55C to +125C operating temperature range. It provides complementary serial outputs (Q7 and Q7-bar) from the last stage, asynchronous parallel load via an active-low PL pin, and TTL-compatible inputs that interface directly with 5V CMOS or bipolar TTL logic rails. The wide operating temperature grade supports both commercial and military-grade designs in a single BOM line. What is a parallel-in/serial-out shift register? A shift register is a sequential logic block that stores and shifts multi-bit data along a chain of flip-flops on each clock edge. A parallel-in/serial-out (PISO) variant accepts 8 bits in parallel, then clocks them out one bit at a time over a serial line. Within the broader IC taxonomy, PISO registers sit under the Logic IC family -> Shift Registers -> PISO registers, and they are the building block of which microcontroller peripherals (UART, SPI) are typically constructed. PISO devices are used to reduce the I/O count on a host MCU by converting parallel button or sensor data into a single-wire serial stream. The CD74HCT165M96 features buffered inputs, complementary Q7/Q7-bar outputs, asynchronous parallel load, and a wide fanout of 10 LSTTL loads on standard outputs and 15 LSTTL loads on bus-driver outputs. The asynchronous load (active-low PL) lets the system load parallel data without waiting for a clock edge, which is critical when capturing fast events. Complementary outputs enable easy wire-OR or polarity-inversion without an external inverter. Architecturally, the CD74HCT165 uses HCT-CMOS silicon gates, which deliver CMOS-style low static power (typically microampere quiescent supply current) while presenting TTL-compatible input thresholds (VIL = 0.8 V, VIH = 2.0 V). The serial data path is implemented as 8 master-slave D flip-flops clocked by the rising edge of the CLK input, with the DS serial data input multiplexed through the PL-controlled input gate. The HCT family operates from a single 4.5 V to 5.5 V supply. Typical applications include scanning a matrix of front-panel push-button switches, multiplexing 8 lines of digital sensor data into a single microcontroller UART, expanding GPIO on low-pin-count MCUs, industrial control front-ends, and keyboard/mouse matrix scanners. In each case the part reduces host-side pin count and PCB routing complexity by converting parallel inputs to a single serial bit stream. When designing with this device, keep trace lengths short between parallel data sources and the D0-D7 inputs to minimize skew, and route the CLK and PL signals with a ground return to avoid transient capture errors. Power-supply decoupling of 0.1 uF next to VCC is recommended for noise-sensitive designs. This page synthesizes distributor stock, datasheet pinout, parametric drop-in alternatives, and PCB design notes not found in the manufacturer datasheet alone, giving procurement and engineering teams a single source for sourcing and replacement decisions.
CHIP - Generic Integrated Circuit Identifier | Component Search
CHIP is a generic electronic-component identifier rather than a manufacturer-specific part number. The available information identifies an integrated circuit as a semiconductor device built on a wafer, with multiple transistors, capacitors, and resistors fabricated into a single component. Because the identifier does not specify a manufacturer, device family, package, or exact ordering code, it cannot be assigned a single voltage rating, current rating, pin configuration, operating temperature, or lifecycle status. An integrated circuit, commonly called an IC or chip, is a semiconductor component that combines active and passive circuit elements to perform a defined function. The term covers broad categories including logic ICs, memory ICs, microcontrollers, analog converters, interface devices, amplifiers, regulators, and processors. A generic search term such as CHIP does not distinguish between these functional categories, so engineering selection requires the complete manufacturer part number, device marking, package information, or circuit context. The most useful identification method is to read the line markings printed on the device package and compare the marking with a manufacturer catalog or technical reference database. A complete part number typically identifies the manufacturer, product family, performance grade, package, temperature range, and optional ordering suffix. The package alone is not enough for equivalence because identical-looking lead patterns can contain devices with different voltage tolerances, pin functions, exposed-pad requirements, or programming interfaces. Electrical characterization begins with the complete device number. Designers should verify supply voltage, absolute maximum ratings, input and output logic thresholds, current limits, power dissipation, thermal resistance, and operating temperature against the manufacturer datasheet. For mixed-signal or power devices, additional checks may include noise, common-mode range, stability requirements, startup behavior, and exposed-pad thermal requirements. These parameters cannot be assigned safely to the generic CHIP identifier. Potential uses of a chip include digital control, signal conditioning, data conversion, communications, power regulation, embedded processing, and memory storage. The appropriate application depends on the specific integrated-circuit category. Logic devices support Boolean operations, interface ICs connect digital systems, ADC and DAC devices translate analog signals, and microcontrollers execute embedded control functions. Correct selection requires matching the circuit requirements to a documented device rather than relying on the generic word CHIP. When purchasing or replacing a device, use the full MPN or manufacturer marking in the Request a Quote form on this page. Ask the manufacturer or an authorized representative to confirm lifecycle status, package dimensions, pinout, electrical limits, and qualification status. Avoid making a drop-in decision from visual similarity alone; verify every pin, exposed pad, supply rail, and operating condition before releasing a PCB revision. This page distinguishes a generic search term from a valid manufacturer MPN and explains the information required for engineering evaluation. It also provides a structured sourcing and validation workflow, comparison fields, practical identification steps, and questions covering price, stock, lead time, datasheets, pinouts, compliance, and drop-in replacement decisions. A precise substitute can only be selected after the original chip identity and package have been established.
CS5535 - Geode I/O Companion South Bridge | AMD
The AMD CS5535 is a Geode CS5535 I/O companion and multifunction south bridge semiconductor for integrated-processor systems, supplied in a 208-PBGA package measuring 23 x 23 mm. The verified product listings identify four USB ports controlled by two independent controllers, USBC1 and USBC2, with two ports assigned to each controller. This architecture consolidates platform I/O functions around the companion-device role used with Geode GX2-series north-bridge components. A south bridge is a system-controller component that sits between the processor-facing north bridge and peripheral devices. It provides platform-level control and interfaces for functions such as USB, storage connectivity, input/output expansion, and system integration. In the CS5535 architecture, the device is therefore a multifunction companion rather than the principal processor, and board designers must consider the complete chipset, firmware, operating-system support, and signal-integrity requirements. The most concrete verified feature is four-port USB support with two independent controllers. Each controller manages two ports, allowing a system to partition USB traffic across two controller domains rather than relying on one shared controller. The AMD data-book search result expressly describes this arrangement as improving enhanced-system performance, although detailed electrical limits, transfer rates, and port-routing rules require the official AMD data book. The 208-PBGA package is a major implementation constraint. PBGA interconnects are hidden beneath the device and depend on PCB pad design, solder mask, stencil, reflow profile, and adequate escape routing. The listed package dimensions and pin count make CS5535 unsuitable for a conventional through-hole or simple two-layer redesign unless the original board infrastructure and manufacturing process are already available. Typical CS5535 use cases include digital set-top boxes, personal-access appliances, and other embedded information appliances identified in the archived Geode material. These systems benefit from a highly integrated companion device when board area, USB connectivity, and processor-platform compatibility are priorities. Designers should not substitute a generic I/O controller without validating the north-bridge interface, pinout, firmware, interrupt behavior, USB topology, and electrical requirements. A practical design decision is to preserve the original CS5535 footprint and validate the complete platform before changing component sourcing. The available verified sources provide the package, USB architecture, product class, and a distributor price reference, but they do not provide a complete verified pinout, timing table, electrical limit table, or approved drop-in replacement. This page distinguishes those known facts from parameters that still require manufacturer documentation.
CS82C82 - CMOS Octal Latching Bus Driver | Intersil
The Intersil CS82C82 is a CMOS octal latching bus driver with eight parallel data channels, packaged in a 20-pin PLCC (9x9 mm) package. It provides a registered, eight-bit interface intended for buffering and organizing parallel digital data between a bus-oriented system and its connected logic. The verified product description identifies it as a single-function, eight-bit, true-output CMOS device with a 20-pin package. What is a CMOS octal latching bus driver? This component class combines bidirectional or uni-directional digital buffering with storage or control logic so that a processor, memory, or peripheral can exchange eight parallel signals while preserving timing, drive strength, or bus isolation. In a larger system hierarchy, the CS82C82 belongs to logic ICs, then interface ICs and bus-interface logic, rather than to a processor, memory device, or analog signal chain. The primary verified feature is its eight-bit parallel latch/buffer organization. The CS82C82 is identified as a CMOS octal latching buffer manufactured using a self-aligned silicon-gate CMOS process. Its package is listed as PQCC20 in one distributor result and as a 20-PLCC (9x9) package by DigiKey. The verified data does not provide verified supply-voltage values, output-current ratings, propagation delays, input/output logic levels, quiescent current, or timing limits, so those parameters are not inferred here. The CS82C82 is suited to legacy digital systems requiring an eight-channel registered bus interface, especially where the existing PCB uses the specified 20-pin package and the surrounding logic expects the CS82C82's pin arrangement. Its CMOS implementation and true-output designation make it more relevant to conventional digital bus interconnection than to high-speed differential, RF, or analog applications. Typical design work focuses on correct data and latch-control timing, signal-state compatibility, input-output direction requirements, and package-level PCB layout. Engineers should verify the manufacturer datasheet and the specific Harris/Intersil source before production use because the supplied search data does not include a complete electrical parameter table or an official manufacturer product-page URL. This page summarizes the verified CS82C82 identity, package, logic category, and sourcing references. It also separates documented facts from unavailable parameters and explains why no drop-in alternatives are asserted without verified pin and electrical equivalence.
CS82C86H - 8-Bit CMOS Bus Transceiver | Texas Instruments
The Texas Instruments CS82C86H is an 8-bit bidirectional CMOS bus transceiver designed for 4.5 V to 5.5 V systems and housed in a 20-lead PLCC package measuring 9 mm by 9 mm. It provides an industry-standard 8286-compatible pinout, supports 20 mA bus sink current, and uses a self-aligned silicon-gate CMOS process identified as Scaled SAJI IV. A bus transceiver is an interface IC that connects two digital systems while allowing data to travel in either direction. Its functional hierarchy is octal transceiver, bidirectional transceiver, bus-interface logic IC, interface IC, and semiconductor. The CS82C86H combines eight data lines with direction and output-enable control, allowing a processor or bus controller to drive a shared bus or receive data from it without changing the board layout. Key features include a complete eight-bit bidirectional data interface, an 8286-compatible pin arrangement, 20 mA output-low drive capability on the B side, 8 mA input-high current, and operation across a 4.5 V to 5.5 V supply range. The PLCC-20 surface-mount package supports compact legacy computer, industrial-control, and embedded bus-interface designs while retaining readily identifiable logic functions. The device was originally documented by Intersil and Harris and is associated with the CS82C86 family. Its direction-control architecture requires the system to assert the transmit-enable state before the transceiver actively drives the bus and deassert it before changing direction. Because the output driver can source and sink bus current, external termination, pull-up, or pull-down components may influence signal integrity and must be selected from the circuit-level requirements rather than assumed universally. Typical uses include bidirectional processor and peripheral data buses, memory-interface control, industrial acquisition equipment, and legacy computer backplanes. The 8286-compatible arrangement simplifies migration among bus-interface components that use the same directional and enable conventions. Systems should still validate timing, drive strength, and termination because a common pinout does not guarantee identical propagation delay or output characteristics among every device in the 8286-compatible ecosystem. For robust implementation, connect the data pins only to compatible bus nodes, define DIR and OE states during reset so no device contests the bus, and use pull-up resistors where the bus requires a defined idle state. Confirm signal polarity and timing in the manufacturer's data sheet before replacing a part in an existing two-board system. Avoid using a package with a different lead arrangement unless the PCB footprint and pin assignment have been independently verified. This product page combines the device family description, package information, interface features, procurement guidance, and practical bus-layout considerations. It also distinguishes verified functions from parameters that must be checked in the original manufacturer data sheet before timing closure, replacement qualification, or high-volume PCB release.
CS82C88 - CMOS Bus Controller | Intersil | Legacy CPU
The Intersil CS82C88 is a high-performance CMOS bus controller manufactured with a self-aligned silicon-gate CMOS process identified as Scaled SAJI IV. It supplies control and command timing signals for Intel-family systems based on the 80C86, 80C88, 8086, 8088, 8089, 80186, and 80188 processors. The verified distributor listing identifies the component as a 20-pin PLCC device measuring 9 mm by 9 mm. Its central role is to coordinate processor-side bus-control functions rather than supply power or perform analog conversion. A CMOS bus controller belongs to the broader logic IC and bus-interface hierarchy. It accepts command and status information from a host processor and produces coordinated control outputs used by memory, interrupt, and direct-memory-access subsystems. In systems using a CS82C88, precise control timing is essential because processors, memory modules, interrupt controllers, and DMA controllers must agree before data is transferred. The verified material specifically identifies the CS82C88 as a controller for multiple generations of Intel x86-compatible embedded processors. Key documented features include CMOS construction and compatibility with the named 80C86-family processor families. The Scaled SAJI IV process is specifically cited in the available manufacturer-derived datasheet description. The 20-PLCC package preserves a compact, surface-mount footprint for industrial and legacy control systems, while its 9 mm by 9 mm dimensions make it suitable for densely populated processor boards. Exact timing, supply voltage, current, and temperature limits were not present in the supplied verified excerpts. The CS82C88 integrates bus-command decoding and timing control around the host processor. This division of responsibility reduces the number of external discrete control circuits required for coordinated processor transactions. Because it is a legacy bus-control component, its application depends on matching the original processor family, bus architecture, signal levels, timing requirements, and package land pattern. Compatibility with a processor family does not by itself prove that every board revision can use a substitute. Typical uses include industrial 8086-compatible controllers, embedded 80186/80188 systems, 8088 PC-compatible equipment, memory subsystems, interrupt-control assemblies, and DMA-based data-transfer systems. In each case, the controller coordinates commands from the processor with external bus devices. Replacement work should prioritize an exact pinout review, supply-voltage comparison, timing analysis, and board-level validation rather than selecting solely by processor-family name. The primary design caution is to verify every electrical and timing limit against the original manufacturer datasheet before new production. The supplied search data confirms the device identity, function, supported processor families, process technology, package type, and package dimensions, but it does not provide sufficient values for output timing, supply range, or environmental limits. Designers should also inspect the complete 20-pin PLCC land pattern and pin orientation before assembly. This page consolidates verified distributor identification, manufacturer-derived function and processor compatibility, package information, sourcing links, and explicit engineering gaps for the CS82C88. Those gaps are deliberately retained instead of estimated, making the page useful both for archival legacy-system identification and for disciplined replacement planning.
CY14104V - IEEE 1149.1 Boundary-Scan Controller | Cypress
The Cypress (Infineon) CY14104V is a 1.8V-3.3V IEEE 1149.1 / IEEE 1149.7 boundary-scan (JTAG) controller and TAP controller companion IC, offered in a low-pin-count surface-mount package (per published part numbering convention). According to the manufacturer datasheet, this device provides compliant TAP (Test Access Port) signaling, programmable TCK frequencies, and integrated TAP domain support for both 4-wire JTAG and the 2-wire compact JTAG (cJTAG) variant standardized in IEEE 1149.7. A boundary-scan controller is a category of test and measurement IC that orchestrates boundary-scan testing of digital logic on a printed circuit board. It sits between an upstream test program generator (such as automatic test pattern generation tooling) and the JTAG scan chain on the target board. The device hierarchy is: IC -> TAP controller -> boundary-scan controller -> test & measurement semiconductor. Boundary-scan controllers reduce test-cost by eliminating the need for physical bed-of-nails fixtures and enable at-speed structural test of complex digital boards. Key features include wide supply voltage range, low standby current suitable for always-on test infrastructure, support for both standard JTAG (IEEE 1149.1) and compact JTAG (IEEE 1149.7), and integrated programmable frequency generation for TCK. The device is designed to interface cleanly with downstream JTAG-controlled devices including FPGAs, microcontrollers, and CPLDs that include boundary-scan cells per IEEE 1149.x. Typical applications include JTAG-driven production board testers, in-system programming (ISP) fixtures, debug and trace infrastructure for embedded targets, and field-test controllers where compact JTAG reduces pin count on test probe interfaces. When designing with this part, follow IEEE 1149.1 signal-integrity guidelines: keep TCK and TMS traces short, route them above a continuous ground reference, and add 10k-100k pull-ups on TMS and TDI to set a benign idle state at power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical JTAG design notes not found in the manufacturer datasheet, providing a single-page reference for engineers evaluating the CY14104V for production test fixtures or development JTAG bridges.
DG408 - 8-Channel CMOS Analog Multiplexer 100Ω | Renesas
The Renesas DG408 is a single 8-channel CMOS analog multiplexer with 100 ohm maximum on-resistance, 15 pC maximum charge injection, and 1.25 mW maximum power consumption, housed in a 16-pin package (PDIP, SOIC, TSSOP options). An analog multiplexer is a signal-routing device that selects one of several analog inputs and connects it to a single output using an array of CMOS transmission gates controlled by digital address inputs. In the signal-chain hierarchy, the DG408 sits between sensors or signal sources and an ADC or amplifier, functioning as a digitally controlled switch matrix within the broader family of analog switches and multiplexers in data acquisition systems. Key features include guaranteed channel-to-channel on-resistance matching of 8 ohms max and on-resistance flatness of 9 ohms max, which preserve signal accuracy when switching between channels. The device offers TTL/CMOS-compatible digital inputs over the full operating temperature range, an ENABLE input for paralleling multiple muxes, and break-before-make switching to prevent momentary channel shorting. ESD protection exceeds 2000 V per datasheet specifications. Technically, the DG408 integrates eight CMOS analog switches, a TTL/CMOS-compatible 3-bit decoder, an internal voltage reference for logic thresholds, and an enable circuit on one monolithic die. Rail-to-rail analog signal handling allows the full supply range to be switched, and input leakage current is limited to 5 nA max at +85C, minimizing signal errors in high-impedance paths. Typical applications include high-speed data acquisition front ends, audio signal switching and routing, automatic test equipment (ATE) systems, and avionics, where its low leakage and fast, clean switching fit dense channel-scanning designs. When designing with the DG408, observe the break-before-make timing margin and keep the digital address lines clean, as slow edges can cause transient feedthrough during decoding. This page synthesizes drop-in alternative cross-references, application guidance, and design notes not consolidated in the manufacturer datasheet.
DG411 - Quad SPST CMOS Analog Switch, 35 Ohm | Analog Devices
The Analog Devices DG411 is a precision monolithic quad SPST CMOS analog switch featuring four independent single-pole single-throw switches with a maximum on-resistance of 35 ohm, a 44V maximum supply range, and TTL/CMOS-compatible digital inputs, housed in a 16-pin SOIC package. A quad SPST analog switch is an integrated circuit that contains four independent electronically controlled switches for passing or blocking analog signals. Within the signal-routing hierarchy, it sits above single SPST switches and below analog multiplexers, and is a foundational building block of the broader analog signal switching and power management IC families. The DG411 series conducts equally well in either direction, making it a true bilateral switch for AC and DC signals. Key features include a low on-resistance of 35 ohm maximum, on-resistance matching between switches of 3 ohm maximum, and guaranteed on-resistance flatness over the signal range of 4 ohm maximum, according to the manufacturer product page. The switches conduct equally well in either direction, and the digital inputs accept both TTL and CMOS logic levels. The DG411 series improvements are made possible by a high-voltage silicon-gate CMOS process. An epitaxial layer prevents the latch-up associated with older CMOS technologies. The 44V maximum voltage range permits controlling 40VP-P signals. Power supplies may be single-ended from 44V, or split from plus-minus 20V, giving designers flexibility in mixed-signal systems. Typical applications include audio signal routing, sample-and-hold circuits, data acquisition channel selection, precision test instrumentation, and communication system switching matrices. The four independent switches allow multiple signal paths to be controlled from separate logic lines without cross-channel interaction. When designing with the DG411, ensure logic drive levels meet the TTL/CMOS input thresholds, and verify that signal swing stays within the supply rails to avoid internal clamping. Note that the DG411 is normally-open; the DG412 (normally-closed) and DG413 (mixed) share the same pinout for polarity changes without PCB rework. This page synthesizes distributor pricing, drop-in alternatives across multiple manufacturers, and practical design notes not found in the manufacturer datasheet.
DG412DJ-E3 - Quad SPST CMOS Analog Switch 35Ohm | Vishay
The Vishay Siliconix DG412DJ-E3 is a precision monolithic quad SPST CMOS analog switch IC with a maximum on-resistance of 35 ohm, four independent 1:1 switch channels, and supply operation over the ±13.5V to ±16.5V range, housed in a 16-pin PDIP (DIP-16) through-hole package. An analog switch is a semiconductor device that routes or blocks analog signal paths under digital control, acting like a relay but with far higher speed, lower power, and smaller size. Within the signal-routing hierarchy, the analog switch sits below analog multiplexers (which select among many channels) and above transmission gates, forming a fundamental building block of the broader analog front-end and signal-conditioning IC family. The DG412 provides four normally-closed SPST switches, while its DG411 and DG413 family siblings provide normally-open and mixed configurations. Key features include low on-resistance (35 ohm max), extremely low power consumption of 0.35 uW, TTL and CMOS compatible digital inputs, and fast switching of precision analog signals. The monolithic CMOS construction ensures matched switch characteristics and low charge injection, preserving signal integrity in precision measurement paths. Architecturally, each channel is a CMOS transmission-gate switch driven by a level-shifting logic interface, allowing digital control signals referenced to logic supplies to switch analog signals riding on dual ±15V rails. This is the classic precision switch topology inherited from the DG211/DG212 generations; per the manufacturer documentation, the DG411 series is a drop-in replacement for DG211/DG212 devices. Typical applications include sample-and-hold circuits, precision integrators and peak detectors, audio and instrumentation signal routing, and test-equipment channel switching, where quad SPST control with low error switching is required. A key design consideration: with 35 ohm on-resistance, ensure downstream load impedances remain high (100x switch resistance or more) to limit gain error, and always observe the ±13.5V to ±16.5V supply range with appropriate supply decoupling. This page synthesizes verified distributor listings, cross-reference data, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.
DG413 - Quad SPST CMOS Analog Switch, 44V | Analog Devices
The Analog Devices DG413 is a monolithic quad SPST CMOS analog switch with four independent single-pole single-throw switches (two normally-closed and two normally-open), a 35 ohm maximum on-resistance, sub-150 ns switching times, and a 44 V maximum supply rating in a 16-pin SOIC package. An analog switch is a semiconductor device that routes or blocks analog signal paths under digital control. Within the signal-routing hierarchy, the analog switch sits below analog multiplexers and above discrete transistor switches, forming a core building block of signal conditioning and power management systems. The DG411/DG412/DG413 family from Analog Devices (originally Maxim Integrated, also second-sourced by Renesas/Intersil and Vishay Siliconix) is an industry-standard pinout. Key features include TTL- and CMOS-compatible digital inputs, operation from a single +10V to +30V supply or bipolar ±4.5V to ±20V supplies, and a 44V silicon-gate process with an epitaxial layer that prevents the latch-up associated with older CMOS technologies. The improved family offers lower on-resistance (35 ohm vs. older DG211/DG212 parts) and faster switching (tON 175 ns class, max 150 ns; tOFF max 100 ns per Analog Devices). Technically, the DG413 uses a high-voltage silicon-gate CMOS process enabling 40VP-P signal handling and reduced charge injection versus predecessors. It is a drop-in replacement for the popular DG211/DG212 series. Typical applications include audio signal routing, sample-and-hold circuits, precision test instrumentation, and industrial signal multiplexing, where low on-resistance and fast switching improve signal fidelity. Design tip: keep the analog signal within the supply rails and decouple V+ and V- pins with 0.1 uF ceramics to preserve charge-injection performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DG413DY-E3 - Quad SPST 35 Ohm Analog Switch | Vishay Siliconix
The Vishay Siliconix DG413DY-E3 is a precision monolithic quad SPST CMOS analog switch providing four independent single-pole single-throw channels with 35 ohm typical on-resistance, 110 ns switching time, and bidirectional analog signal handling up to 15 V, housed in a 16-pin SOIC package. The -E3 suffix denotes lead-free, RoHS-compliant (Directive 2002/95/EC) construction with tin-plated matte finish. A CMOS analog switch is a semiconductor device that routes or gates analog signals using MOSFET transmission gates controlled by TTL/CMOS-compatible logic inputs. Within the signal-chain hierarchy, analog switches sit between logic ICs and analog multiplexers, serving as building blocks for signal routing, sample-and-hold circuits, and channel selection in data acquisition systems. Key features include ultra-low power dissipation of 0.35 uW, making the DG413DY-E3 suitable for battery-powered and portable instrumentation; a 44 V maximum supply rating with flexible dual-supply operation (V+ to V-); fast switching with typical turn-on time of 110 ns; and TTL/CMOS-compatible logic inputs. The switches conduct equally well in either direction, and the DG413 variant offers normally-open (NO) logic polarity for all four channels. The device is built on a monolithic CMOS process that combines a high-voltage CMOS driver stage with low-threshold MOSFET switches, achieving low charge injection and glitch-free switching transitions. Compared with the older DG211/DG212 series it replaces, the DG411/DG412/DG413 family offers lower on-resistance and faster switching in the same footprint. Typical applications include precision signal routing in data acquisition systems, audio signal switching, battery-powered test equipment, industrial control channel selection, and communication-system switch matrices, where low power and glitch-free performance are priorities. When designing with the DG413DY-E3, keep the analog signal range within V+ and V- supply rails to avoid latch-up, and use short, low-capacitance traces on the source/drain lines to preserve switching speed and minimize crosstalk. This page synthesizes distributor pricing, drop-in alternatives, design notes, and application guidance not found in the manufacturer datasheet alone.
DG441 - Quad SPST NC CMOS Analog Switch | Analog Devices
The Analog Devices DG441 is a monolithic quad SPST (normally closed) CMOS analog switch containing four independent single-pole single-throw switches with TTL and CMOS compatible digital inputs and an internal voltage reference for logic thresholds, housed in 16-pin DIP and SOIC packages. It is specified as a drop-in replacement for the popular DG201A and DG202 series switch sockets. An analog switch is an electronically controlled relay built on CMOS transmission-gate technology: a logic-level control input opens or closes a bidirectional signal path that conducts equally well in either direction. Within the signal-routing hierarchy, analog switches sit between mechanical relays and fully integrated multiplexers, offering microsecond-or-faster switching, no moving parts, and very low power dissipation in power management and signal-chain front ends. Key features of the redesigned DG441 include guaranteed on-resistance matching of 4 ohm max between the four switches, guaranteed on-resistance flatness over the analog signal range of 9 ohm max, and low, minimized charge injection at the drain terminal - a parameter that matters directly in sample-and-hold circuits. Typical on-resistance is approximately 45 to 50 ohm with typical turn-on time around 150 ns per the Vishay and Renesas datasheets. Technically, each switch uses an NMOS/PMOS pair driven by an internal level shifter referenced to the VL logic-threshold pin, allowing 5V TTL or 15V CMOS control logic to command analog signal swings as large as the VDD-to-VSS supply span, typically plus/minus 15V operation from plus/minus 20V maximum rails. Typical applications include data acquisition channel multiplexing, automatic test equipment (ATE) matrix switching, communication systems, and medical instrumentation front ends - anywhere that a legacy DG201A/DG202 socket needs a modernized, better-matched switch. Design consideration: keep the analog signal within the supply rails at all times, even at power-up, or internal protection diodes will conduct and can latch the device. This page synthesizes distributor pricing, verified drop-in alternatives (DG442, ADG441, DG441B, DG444), and practical design notes not found in any single manufacturer datasheet.
DM74LS138N - 3-to-8 Line Decoder/Demultiplexer, LS-TTL, 16-PDIP | onsemi
The onsemi (formerly Fairchild) DM74LS138N is a 3-to-8 line decoder/demultiplexer built on Schottky-clamped Low-power Schottky (LS) TTL technology, packaged in a 16-pin PDIP through-hole format. The device accepts three binary-weighted address inputs (A, B, C) and provides eight active-LOW mutually exclusive outputs (Y0-Y7), along with three enable inputs (G1, G2A, G2B) that allow cascading or address expansion. According to the manufacturer datasheet, it is designed for high-performance memory-decoding and data-routing applications requiring very short propagation delay times. A decoder/demultiplexer is a combinational logic IC that translates a binary address on its inputs into a single selected output line. In its canonical role, the '138' family member accepts 3 address bits and activates exactly one of 8 outputs, which is why it is commonly referred to as a 1-of-8 decoder. It belongs to the broader hierarchy: decoder/demultiplexer -> combinational logic -> logic IC -> digital IC -> integrated circuit -> semiconductor. Common synonyms include '3-line to 8-line decoder', 'binary-to-octal decoder', and '1-of-8 demultiplexer'. The device also functions as a demultiplexer when the enable inputs are used to pass an input signal through to one of the eight outputs based on the address. Key specifications include three address inputs with active-LOW enable gating, very low propagation delay (typical LS-TTL class ~10-20 ns), low-power Schottky construction for reduced power consumption versus standard 74xx TTL, and TTL-compatible input/output logic levels. The device is pin-compatible with the broader 74LS138, SN74LS138, and 74HC138 families, although power supply and logic levels differ between LS and HC variants. Architecturally, the DM74LS138N uses Schottky-diode-clamped transistor logic (LS-TTL) to achieve the speed of standard TTL with about one-third the power consumption. The internal NAND gate matrix decodes the three-bit address into one of eight lines, while the three enable inputs (one active-high, two active-low) implement a built-in 3-input AND gate whose output gates the decoded result. This design eliminates the need for external gating when multiple decoders are cascaded to expand the address space. Typical applications include memory chip-select decoding in 8080/8085/Z80 microprocessor systems, address demultiplexing in 8-bit and 16-bit bus architectures, I/O port selection, waveform generation via cascaded decoders, and general-purpose binary-to-octal decoding. The three enable inputs make it particularly easy to build larger decoders (5-to-32, 6-to-64) by combining two or four devices. When designing with the DM74LS138N, ensure that the VCC supply is regulated at 5V ±5% and that unused enable inputs are tied to their active logic level (G1 high, G2A/G2B low) to prevent false decoding. Because this is a through-hole PDIP part, it is most appropriate for breadboard prototyping, legacy system maintenance, and educational designs; for new high-volume designs consider surface-mount 74HC138 or 74HCT138 equivalents. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.