Logic ICs
بەرهەمەکان (720+)
ATF16V8CZ-12XC - 12ns 8-Macrocell PLD | Microchip
The Microchip Technology ATF16V8CZ-12XC is a 12 ns high-performance EECMOS programmable logic device with eight macrocells, up to 16 inputs, and eight configurable I/O outputs in a 20-pin TSSOP package. It operates from a 5 V supply and combines electrically erasable Flash memory with CMOS- and TTL-compatible interfaces. A programmable logic device, or PLD, is a semiconductor whose digital logic function is defined after manufacture. The ATF16V8CZ belongs to the PAL-compatible 16V8 architecture and extends beyond generic 16R8 devices by supporting combinational, registered, and complex registered configurations. It is used when fixed-function glue logic would require several gates, counters, or discrete logic ICs. The device provides eight macrocells, with eight product terms allocated to each output. Its maximum pin-to-pin delay is 12 ns, making it appropriate for control, decoding, interface, and state-machine functions that do not require a modern FPGA. The ATF16V8CZ also provides an edge-sensing power-down mode with 5 uA typical current and a low 25 uA standby-power specification, helping conserve power in equipment with intermittent operation. Its EECMOS architecture uses electrically erasable Flash memory, allowing programmed logic to be erased and rewritten rather than permanently fused. The architecture is designed as a superset of generic 16R8 and many 20-pin combinatorial PLD arrangements, simplifying migration from older GAL or PAL devices when the pin configuration and logic equations remain compatible. Typical uses include printer and copier control, industrial panel interfaces, legacy bus decoding, addressable logic, instrumentation control, and small embedded systems requiring high-density combinational or registered functions. The 20-pin TSSOP package also supports compact, surface-mounted PCB layouts where a larger PLCC package would be less convenient. Designers should verify the device's registered-output mode, pin assignments, and power-down behavior against the manufacturer datasheet before replacing an older PAL or GAL. Programming equipment, device-file compatibility, and the distinction between combinational and registered outputs are as important as package dimensions when establishing a drop-in replacement. This product page combines the manufacturer's electrical and architectural details with package-level guidance, application analysis, and clearly qualified same-family alternatives. It also identifies where timing, pin-level, lifecycle, and compliance information must be confirmed before production release.
ATF16V8CZ-15JC - 15ns 250-Gate EEPLD | Microchip Technology
Microchip Technology ATF16V8CZ-15JC is a 250-gate electrically erasable programmable logic device with eight macrocells, up to 16 inputs, eight I/O paths, and a 15 ns propagation delay. The device operates from a 5 V supply and is packaged in a 20-pin PLCC J-lead surface-mount package. Its combination of configurable logic, CMOS-compatible interfacing, and low-power operation suits established control, decoding, and glue-logic designs. An electrically erasable programmable logic device, or EEPLD, is a programmable semiconductor that stores configurable AND/OR-style logic functions in nonvolatile memory. The ATF16V8CZ family belongs to the broader PLD hierarchy and provides a permanent logic implementation without repeatedly programming a microcontroller. It can implement registered or combinatorial functions and replace combinations of discrete gates in compact industrial, telecommunications, and consumer equipment. Key features include eight macrocells, eight outputs with eight product terms per output, support for up to 16 inputs, and 5 V CMOS and TTL-compatible inputs and outputs. The -15 speed grade provides a 15 ns propagation delay. Standby power is low at 25 µA, and zero-power operation is a stated family feature intended to reduce power consumption when the device is not active. The ATF16V8CZ architecture extends the generic 16V8 arrangement and can directly replace 16R8-family devices and many 20-pin combinatorial PLDs. Its configurable operating modes support common combinational and registered logic patterns. Configuration software determines how the input and output resources are assigned, allowing a single PLD architecture to serve multiple control functions while reducing discrete logic count. Typical applications include industrial automation, consumer electronics, telecommunications equipment, address decoding, interface qualification, and small control-logic subsystems. The 20-pin PLCC package supports compact surface-mount assemblies, while its 5 V interface simplifies integration with conventional TTL and CMOS logic families. During PCB design, verify every PLCC pad against the manufacturer pin-description table and preserve adequate copper around the J-leads for soldering and inspection. Confirm the programmed device type, pin polarity, and registered-versus-combinatorial behavior against the original design before replacing an installed ATF16V8CZ-15JC. This product overview combines the ATF16V8CZ family specifications with package details, drop-in replacement guidance, comparison parameters, and practical implementation notes. It is designed to help engineers evaluate timing, logic architecture, interface compatibility, and replacement risk before integrating this programmable logic device into a new or existing board.
ATF16V8CZ-15JI - 15ns 5V EEPLD | Microchip Technology
Microchip Technology ATF16V8CZ-15JI is a 5 V electrically erasable programmable logic device with eight macrocells, eight I/O paths, support for up to 16 inputs and a 15 ns propagation delay in a 20-PLCC J-lead surface-mount package. It belongs to the ATF16V8CZ family of zero-power, high-performance EECMOS PLDs that provide 250 gates of programmable logic. A simple programmable logic device, or SPLD, is a programmable-logic IC that combines configurable AND/OR logic structures with registered or combinational operating modes. In the broader semiconductor hierarchy, an SPLD is a programmable-logic device within the logic-IC family. The ATF16V8CZ architecture can emulate many 16R8 devices and most 20-pin combinatorial PLDs, making it useful for consolidating several gates, decoders, counters and control functions into one nonvolatile logic component. The ATF16V8CZ architecture includes eight outputs, each allocated eight product terms, and supports three operating modes selected automatically by software. Key characteristics include a 5 V supply, CMOS- and TTL-compatible inputs and outputs, a 15 ns maximum speed grade, and low-power operation. The electrically erasable architecture supports in-circuit reprogramming, allowing logic changes without replacing the device or redesigning the surrounding board. The device combines eight macrocells with as many as 16 dedicated inputs and eight configurable I/O paths. Its 250-gate capacity provides considerably more integration than a small discrete PAL implementation while requiring less design effort than an FPGA. The ATF16V8CZ family is especially appropriate for fixed-format glue logic, industrial control interfaces, decoding functions, bus arbitration, state sequencing and other designs where compact logic density, predictable timing and simple programming are priorities. Typical uses include industrial automation, consumer electronics and automotive control logic. The -15JI suffix identifies the 15 ns speed grade with industrial temperature grading, while the J-lead 20-PLCC package supports surface-mount assembly where a leaded package is preferred over a fine-pitch quad flat package. It can also serve as a system-originated logic replacement when the original board requires a 20-pin PLCC footprint. The principal design consideration is package and pin compatibility. A replacement must match the 20-PLCC footprint, supply voltage, macrocell count, input/output assignment and programming architecture. Confirm the complete pin description and configuration requirements against the manufacturer datasheet before modifying an existing PCB or transferring a programmed logic design. This product page combines the ATF16V8CZ family architecture, verified package and timing characteristics, same-footprint alternatives, comparison parameters and practical replacement guidance. It is intended to help engineers identify the correct 20-PLCC EEPLD for new designs, legacy-board maintenance and controlled redesigns without assuming that every similarly named ATF16V8 variant is interchangeable.
ATF16V8CZ-15PC - 15ns 5V EECMOS SPLD | Microchip Technology
The Microchip Technology ATF16V8CZ-15PC is a 5 V, 250-gate electrically erasable programmable logic device with 8 macrocells, up to 16 inputs, 8 I/O outputs, and a 15 ns speed grade in a 20-pin PDIP package. It uses EECMOS electrically erasable Flash technology, allowing the configuration to be reprogrammed without removing the device from the circuit. Maximum pin-to-pin delay reaches 12 ns, while CMOS- and TTL-compatible interfaces support both modern and legacy logic levels. An SPLD is a simple programmable logic device: a single monolithic IC containing AND/OR-style logic structures that are configured by the user for a specific combinational or registered logic function. In the broader semiconductor hierarchy, the ATF16V8CZ-15PC belongs to the programmable-logic family, combines PLD and FPGA attributes in function, and provides a compact alternative to a discrete gate array. Its 8 macrocells can implement multiple logic terms in one package, reducing board area and external component count. Key features include 250 gates of logic capacity, electrically erasable Flash configuration memory, zero-power operation for the ATF16V8CZ family, 8 configurable I/O outputs, and a maximum of 16 input paths. The -15 suffix identifies a 15 ns device grade, and the -PC suffix identifies the commercial-temperature 20-pin PDIP configuration. A 5 microampere typical edge-sensing power-down mode and 25 microampere standby current support low-power system designs. The ATF16V8CZ architecture consolidates several older 20-pin PAL device patterns and supports programmed operating modes selected automatically by development software. The device is suited to glue logic, control decoding, interface adaptation, and legacy product revisions where a compact, reprogrammable fixed-function alternative is preferable to maintaining a full FPGA or microcontroller. Its 20-pin through-hole package also simplifies inspection, prototyping, and hand rework. Typical uses include industrial control interfaces, legacy peripheral adaptation, address decoding, alarm and interlock logic, and compact control subsystems. The electrically erasable architecture is especially useful during development because logic changes do not require new devices or socketed parts. A 5 V supply and 15 ns timing class fit systems that use legacy control buses rather than high-speed modern processor interfaces. When laying out a board, keep the 5 V supply rail and ground return planes low impedance, and route the 20-pin PDIP footprint for straightforward through-hole assembly. Program the device with the manufacturer's logic-development software and verify unused macrocell configurations to prevent outputs from floating. Confirm the commercial operating temperature range against the system enclosure temperature before releasing the production design. This page combines the manufacturer device description with distributor package and speed-grade data, practical PLD design guidance, and a pin-compatible comparison covering three same-footprint alternatives. It also identifies package and electrical details that engineers should confirm against the manufacturer datasheet before schematic release or production procurement.
ATF16V8CZ-15PI - 8-Macrocell 15 ns EE PLD | Microchip
Microchip Technology ATF16V8CZ-15PI is an 8-macrocell electrically erasable programmable logic device with 15 ns propagation delay, 16 maximum inputs, eight I/O paths, and a 20-pin PDIP package. It operates from a 5 V supply and combines CMOS-compatible and TTL-compatible interfaces in a low-power architecture designed to consolidate multiple 20-pin PAL functions. An EEPLD is a programmable logic device that stores its logic configuration in electrically erasable memory. It belongs to the programmable-logic hierarchy alongside PAL devices, CPLDs, and FPGAs. Unlike a fixed gate-level implementation, an ATF16V8CZ-15PI can be programmed for combinational or registered logic, allowing product revisions to be handled without changing the PCB layout. The device provides up to 16 inputs, eight I/Os, and eight macrocells in a 250-gate-class logic design. Its stated 15 ns propagation delay supports moderate-speed control, interface, and decoding functions. The ATF16V8CZ also features zero-power operation, 25 uA standby power, and CMOS and TTL-compatible inputs and outputs for integration with conventional digital logic families. Programming uses electrically erasable flash technology, allowing a configured device to be reprogrammed during development, production test, or field updates. The 20-pin PDIP format supports conventional through-hole assembly and prototyping, while the 250-gate logic capacity provides more flexibility than a small fixed PAL. Applications are still bounded by the eight macrocell and eight-I/O architecture, so designs requiring extensive parallelism should move to a larger CPLD or FPGA. Typical uses include industrial control logic, legacy interface decoding, printer and peripheral controllers, data acquisition, instrumentation, and embedded system glue logic. The device is particularly useful when a design needs configurable Boolean functions, registered outputs, or a compact replacement for several small PAL devices without requiring a complex FPGA development flow. Designers should preserve the ATF16V8CZ-15PI pin assignments when programming the device and use the manufacturer datasheet pin-description table to assign inputs, outputs, clock, and control functions. Confirm the 5 V supply tolerance, unused input states, and output drive requirements for every connected net. The through-hole package also requires adequate board spacing and lead-bend clearance during insertion and soldering. This product data combines the device architecture, package information, search-focused technical questions, and drop-in comparison guidance into an engineering-focused reference for designers evaluating a compact, reprogrammable logic solution.
ATF16V8CZ-15SC - 15ns 8-Macrocell EEPLD | Microchip
The Microchip Technology ATF16V8CZ-15SC is a 5 V electrically erasable programmable logic device with 250 gates, 8 macrocells, up to 16 inputs, and 8 configurable I/O outputs. It provides a 15 ns propagation-delay grade in a 20-SOIC package, making it suitable for compact CMOS and TTL-compatible control, decoding, and glue-logic designs. An EEPLD is an electrically erasable programmable logic device: a user-programmed logic IC that stores a Boolean function in nonvolatile internal memory. It belongs to the programmable-logic hierarchy, where a PLD sits above individual gate arrays and provides a compact implementation of multiple sum-of-products logic functions. The ATF16V8CZ architecture emulates many 20-pin PAL devices and most 20-pin combinatorial PLDs, simplifying migration from older fixed-logic designs. The ATF16V8CZ uses eight output macrocells, with each output allocated eight product terms. Its architecture supports up to 16 inputs and eight I/O outputs, while its CMOS-compatible inputs and outputs allow operation with both CMOS and TTL logic families. Low-power operation is reinforced by a 25 µA standby-current specification and the family’s zero-power designation, which is useful in systems where inactive logic should not create unnecessary static demand. Three operating modes are selected automatically by the programming software, allowing the same device architecture to implement registered, combinatorial, and complex logic functions. The ATF16V8CZ architecture incorporates a superset of the generic 16R8 architecture and supports direct replacement of the 16R8 family and most 20-pin combinatorial PLDs. This broad compatibility makes it useful for consolidating several small PAL implementations into one device. Typical uses include industrial automation, consumer-equipment control, interface decoding, state-machine implementation, address decoding, and compact automotive control logic. The 15 ns device grade is particularly relevant when the logic path must operate close to the system clock while retaining the simple programming workflow associated with classic GAL16V8 and PAL-compatible devices. Designers should assign each macrocell using the manufacturer’s software and verify the resulting pin assignments against the device programming file. The 20-SOIC package requires adequate board spacing, and unused inputs should be handled according to the datasheet’s stated input rules. The commercial-temperature ordering code should also be checked against the enclosure and system-temperature requirements before deployment.
ATF16V8CZ-15SI - 5V 15ns 250-Gate SPLD | Microchip Technology
The Microchip Technology ATF16V8CZ-15SI is a 5 V, electrically erasable programmable logic device (EEPLD) in the 16V8 family, providing 250 gates, eight macrocells, and up to 16 inputs with eight I/Os. It uses a 15 ns maximum pin-to-pin propagation-delay grade and is packaged in a 20-pin SOIC surface-mount package. The device is intended for compact combinational and registered logic implementations where programmable changes provide a practical alternative to a fixed gate array. A simple programmable logic device, or SPLD, is a user-programmable semiconductor that combines a programmable AND array, configurable OR logic, and output macrocells into one integrated circuit. Within the broader logic hierarchy, the ATF16V8CZ belongs to the EEPLD family, then to programmable logic devices, logic ICs, and integrated circuits. Its 16V8 architecture emulates many 20-pin PAL devices and most 20-pin combinatorial PLDs, making it useful for glue logic, interface conditioning, control decoding, and legacy product support. The 250-gate equivalent architecture and eight macrocells provide substantially more programmable logic capacity than a small discrete gate implementation. The 5 V supply operation supports CMOS-compatible and TTL-compatible inputs and outputs according to the manufacturer information. A 15 ns propagation-delay grade is suitable for control and data-routing functions that do not require the performance of a modern FPGA or high-speed processor. Standby power is specified at 25 microamperes, supporting low-power operation in equipment that spends time inactive. The ATF16V8CZ architecture is electrically erasable, allowing a programmed configuration to be removed and replaced without removing the device from the circuit. This is useful during development, production testing, and field upgrades where logic requirements evolve. Its eight macrocells allocate product terms to outputs, while the input structure supports combinatorial and registered functions described by the ATF16V8CZ programming tools. Typical applications include industrial control interfaces, legacy peripheral emulation, keyboard and display decoding, programmable signal conditioning, and compact subsystem logic. The device can also replace multiple 74-series logic functions when board space, inventory, or design-change requirements favor a single programmable device. Its 20-pin SOIC package supports conventional surface-mount assembly, although engineers should verify the exact pin assignment and electrical limits in the manufacturer datasheet before replacing an existing board. The principal design consideration is timing margin. Although the 15 ns grade provides a defined pin-to-pin delay, external combinational logic, cable or connector delays, and system clock requirements can still determine whether a design meets its timing budget. Use the manufacturer programming and test tools to validate the implemented logic, and follow the datasheet for input, output, power, and package recommendations. This page combines the device architecture, manufacturer specifications, replacement considerations, and practical design guidance for engineers evaluating the ATF16V8CZ-15SI.
ATF22LV10C-10JC - 10ns 500-Gate CMOS PLD | Microchip Technology
The Microchip Technology ATF22LV10C-10JC is a high-performance CMOS programmable logic device with 10 macrocells, approximately 500 gates, and a 10 ns processing speed in a 28-pin PLCC package. It operates across a 3.0 V to 5.5 V supply range and stores its configuration in electrically erasable flash memory, allowing the programmed logic to be retained without a separate external memory device. The ATF22LV10C-10JC is a low-voltage member of the ATF22V10C family. A simple programmable logic device, or SPLD, is a user-programmable semiconductor that combines AND, OR, and related logic functions into one configurable integrated circuit. Within the programmable-logic hierarchy, the ATF22V10C belongs to the SPLD family and then to the broader PLD and programmable-logic-device categories. Its primary engineering advantage is consolidated glue logic: several combinational or registered functions can be implemented in one device rather than across multiple separate gate ICs. Key features include 10 macrocells, a maximum speed grade of 10 ns, operation from 3.0 V to 5.5 V, and electrically erasable flash configuration memory. The macrocell architecture supports programmable product terms and configurable output polarity. A user-controlled power-down function can reduce standby current to 10 uA typical, making the device useful when system power management and reliability are more important than maximum operating speed. The ATF22LV10C uses CMOS processing and provides a simple alternative to mask-programmed logic, field-programmable gate arrays, and discrete gate packages. Programming support allows the design to be changed during development or service without replacing a permanently programmed mask. The 28-pin PLCC footprint is a surface-mount package measuring 11.51 mm by 11.51 mm according to the product listing. Pin and function assignments should be checked against the manufacturer package drawing before layout or replacement. Typical applications include industrial control interfaces, address decoding, command multiplexing, data-routing logic, and compact embedded control blocks. It is especially suitable for designs requiring retained configuration, low voltage operation, and a modest logic-density requirement. The 10 ns speed grade also provides useful timing margin for common control, interface, and bus-logic functions when operated within the specified voltage and temperature limits. The primary design consideration is confirming that the 3.3 V ATF22LV10C family matches the voltage requirements of the surrounding logic. Do not substitute the 5 V ATF22V10C family without reviewing every supply and signal level. Preserve the power-down feature only where its state during reset and normal operation is correctly defined, because an incorrectly controlled PD input can interrupt operation. This product overview combines electrical characteristics, package information, application guidance, and a drop-in comparison of compatible ATF22LV10C speed and temperature grades. Use the manufacturer datasheet pin-description and package tables to assign tracks, validate programming settings, and confirm absolute operating limits.
ATF22LV10C-10JU - 10ns Low-Voltage EEPLD | Microchip
The Microchip ATF22LV10C-10JU is a low-voltage electrically erasable programmable logic device with 10 macrocells, 500 gates, a 10 ns propagation delay, and a 28-pin PLCC package. It operates across a 3.0 V to 5.5 V supply range and combines electrically erasable flash memory with user-controlled power-down capability for low-power logic systems. An EEPLD, or electrically erasable programmable logic device, is a semiconductor that stores a logic configuration in nonvolatile flash memory. It belongs to the programmable-logic-device hierarchy and provides a compact alternative to conventional AND-OR gate arrays when a design needs reconfigurable combinational or registered logic without repeatedly replacing a fixed ASIC. The device provides 10 macrocells organized into 500 logic gates and supports a 10 ns propagation-delay grade. Its low-voltage architecture permits operation from 3.0 V to 5.5 V, while the optional power-down pin places the device into a low-consumption state with a typical standby current of 10 uA. This combination makes it useful for portable, industrial-control, and general embedded logic implementations. The ATF22LV10C uses electrically erasable flash memory, allowing the programmed configuration to be retained when power is removed and then reprogrammed as system requirements evolve. The 28-pin PLCC package uses J-leaded surface-mount construction. Industrial-temperature operation extends from -40 C to +85 C, and guaranteed timing, supply-current, and logic-threshold parameters are specified across that range. Typical applications include industrial control interfaces, legacy peripheral emulation, address decoding, glue logic, keyboard and display controllers, and small embedded systems that need a compact reconfigurable logic block. The 10 ns speed grade also permits operation in higher-speed control paths than slower 15 ns or 30 ns family variants, provided the complete system timing is checked. Designers should use the pin-description table and programming guidance in the Microchip manufacturer datasheet when assigning package connections. Place decoupling close to the supply pins, keep the power-down control unambiguous, and confirm that every configured macrocell and I/O remains valid at the minimum supply voltage used by the finished product. This product summary organizes the device's key specifications, pinout considerations, applications, and verified drop-in alternatives. It also highlights practical differences among temperature grades and related ATF22V10C devices so engineers can distinguish electrical compatibility from merely similar catalog specifications before approving a replacement.
ATF22LV10C-10PC - 10ns 22V10 CMOS PLD | Microchip
The Microchip ATF22LV10C-10PC is a 10 ns high-performance 22V10 electrically erasable programmable logic device with 10 macrocells, 500 gates, and a 24-pin PDIP package. It operates across a 3.0 V to 5.5 V supply range and combines configurable logic with electrically erasable flash memory. The device also provides a user-controlled power-down function with typical standby power of 10 uA. A simple programmable logic device is a programmable semiconductor used to implement compact combinational or registered logic functions. The ATF22LV10C belongs to the broader SPLD family, combining programmable logic architecture with a nonvolatile configuration memory. Its 22V10 organization provides 10 macrocells, while the 500-gate implementation supports control, decode, interface, and compact sequencing functions without requiring a larger FPGA or microcontroller. The -10 speed grade provides a maximum propagation delay of 10 ns and supports 3.3 V operation in the listed distributor description. Its 3.0 V to 5.5 V operating range permits use across industrial and commercial supply conditions. Electrically erasable flash memory allows the programmed configuration to be rewritten during development, production, or field updates. A configurable power-down pin can reduce standby consumption to 10 uA typical when the system is not actively using the logic. The ATF22LV10C combines a PAL-type 22V10 logic structure with on-chip nonvolatile memory. Each macrocell can be configured for combinational or registered operation, allowing several common finite-state-machine, address-decoding, and control functions to be consolidated into one device. The 10 ns propagation delay class is appropriate for interfaces and control logic that must respond within a defined clock interval without the complexity of a larger programmable-logic array. Typical uses include industrial interface logic, telecommunications control, battery-powered instrumentation, embedded control glue, legacy peripheral emulation, and compact system-sequencing logic. The device is particularly useful when several Boolean conditions, latches, counters, or state transitions can be placed in one package and updated without a fabrication-time mask change. Designers should preserve the ATF22LV10C pin assignment when creating a PCB because programmed PLD pin relationships may not match the logical function placed on those pins. Confirm the power-down configuration, supply voltage, timing budget, and unused I/O treatment in the manufacturer datasheet before releasing the layout. This product page combines the ATF22LV10C-10PC operating characteristics, package constraints, compatible family options, and practical implementation guidance to support schematic capture, PCB layout, sourcing, and second-source qualification.
ATF22LV10C-10SU - 10ns 24V10 Flash PLD | Microchip
Microchip ATF22LV10C-10SU is a high-performance CMOS simple programmable logic device with 10 macrocells, electrically erasable flash memory, and a 10 ns speed grade in a 24-pin SOIC package. The ATF22LV10C family supports operation across the 3.0 V to 5.5 V supply range and provides a user-controlled power-down mode with 10 μA typical standby power. A simple programmable logic device, or SPLD, is a user-programmable semiconductor that combines AND-OR logic structures with configuration memory. An SPLD occupies the hierarchy above individual gates but below a field-programmable gate array. The ATF22LV10C provides 500 gates, 10 macrocells, and reusable nonvolatile flash configuration memory for compact control, decoding, interface, and state-machine implementations. The device offers a 10 ns speed grade, 24 I/O pins, and a 3.0 V to 5.5 V operating range. Its optional pin-controlled power-down function lets the PD input place the device into a low-power state without removing configuration data from flash memory. This makes the ATF22LV10C useful in systems where a logic function must remain quickly available after power is restored. The electrically erasable flash architecture supports in-circuit reprogramming, allowing a design to be updated without replacing the component. Flash retention removes the need for a separate configuration PROM, while the compact SOIC-24 package supports conventional surface-mount assembly. The combination of 500 gates and 10 macrocells is suitable for moderate-complexity combinational and sequential logic rather than large processor or FPGA workloads. Typical uses include industrial control decoding, peripheral-interface logic, keypad and display controllers, instrumentation signal conditioning, power-sequencing helpers, and embedded system glue logic. A 3.3 V system can use the device directly within its specified supply range, while 5 V designs can also use the same family when timing and temperature requirements are met. When laying out a board, place the decoupling capacitor close to the power pin and route the configuration, clock, and I/O signals away from noisy switching nodes. Confirm the package pin assignment, programming voltage, timing margin, and power-down polarity against the manufacturer datasheet before releasing a PCB. This page combines the ATF22LV10C family architecture, verified package and speed information, practical replacement guidance, and design-oriented comparison points to support component selection and implementation.
ATF22LV10C-10XU - 10ns Low-Voltage EEPLD | Microchip
The Microchip Technology ATF22LV10C-10XU is a 10 ns, low-voltage electrically erasable programmable logic device with 10 macrocells, approximately 500 gates, and 10 user I/Os in a 24-pin TSSOP package. It operates across the ATF22LV10C family's 3.0 V to 5.5 V range and supports in-system programming through electrically erasable flash memory. An EEPLD is a user-programmable semiconductor that combines fixed logic-array architecture with nonvolatile configuration memory. The ATF22LV10C belongs to the SPLD family of programmable logic devices and provides a compact alternative to a collection of individual AND, OR, and flip-flop gates. Its 22V10 architecture uses a variable product-term structure, with each output receiving approximately 8 to 16 product terms and additional product terms supporting synchronous and asynchronous reset. Key features include a maximum propagation delay of 10 ns, a 10 ns speed designation, 10 macrocells, approximately 500 gates, and a user-controlled power-down mode with 10 μA typical standby current. The device supports the 3.3 V-oriented ATF22LV10C family and is identified as an industrial-temperature component in distributor catalog data. Its nonvolatile flash configuration allows logic designs to be reprogrammed without removing the device from the circuit. The variable product-term architecture allows the same physical device to implement multiple Boolean functions, control logic, decoding, and registered state-machine functions. The ATF22LV10C architecture is compatible with the classic 22V10 pin arrangement, making it useful for consolidating small amounts of glue logic. Microchip documentation also identifies the ATF22LV10C as a direct replacement for the corresponding Xilinx XCR22LV10 family where package and device requirements are matched. Typical applications include industrial control-panel decoding, peripheral-interface qualification, legacy equipment upgrades, address decoding, keyboard or display control, compact control sequencers, and system-management logic. Its 10 ns access performance is appropriate when logic propagation must remain short relative to surrounding control and interface circuits. When laying out a design, preserve the 22V10-compatible pin arrangement and provide the device with clean supply decoupling. Place programming-interface and decoupling connections according to the manufacturer's recommended schematic, and account for signal propagation, setup, and hold requirements around registered outputs. Verify the programmed configuration in-system before treating the circuit as production-ready. This product page combines the manufacturer's architecture information with distributor package and speed details, pin-compatible same-family options, and practical implementation guidance. It is intended to help engineers identify the correct programming device, plan a PCB revision, and evaluate whether the ATF22LV10C architecture satisfies legacy 22V10 logic requirements.
ATF22LV10C-15XC - 15ns CMOS SPLD | Microchip Technology
The Microchip Technology ATF22LV10C-15XC is a 3.3 V CMOS simple programmable logic device with 10 macrocells, 500 gates, and a 15 ns speed grade in a 24-pin TSSOP package. It uses electrically erasable flash memory for in-circuit reprogramming and includes a user-controlled power-down mode that reduces standby current to a typical 10 µA. A simple programmable logic device is a PLD that combines a programmable AND-array, configurable product-term logic, and dedicated I/O resources into a compact logic implementation. Within the broader semiconductor hierarchy, the ATF22LV10C belongs to the SPLD family, which sits below larger CPLD and FPGA devices. It is intended for consolidation of several gates, decode functions, counters, state machines, and control logic where a small fixed-capacity device is more appropriate than a general-purpose microcontroller or FPGA. The ATF22LV10C family supports operation across a 3.0 V to 5.5 V range for industrial and commercial temperature grades. The -15 suffix identifies the 15 ns performance class, while the -XC ordering code denotes the commercial-temperature TSSOP configuration. Each macrocell uses a variable product-term architecture, and each output is assigned from 8 to 16 product terms, allowing moderately complex Boolean functions to be realized in one device. Electrically erasable flash memory permits the programmed configuration to be changed without removing the package from the circuit. The architecture combines that reprogrammability with a compact 24-pin TSSOP footprint and low-power shutdown control. This makes the device useful for prototype stabilization, production configuration control, board-level glue logic, and compact control systems that require deterministic combinational or registered logic without the overhead of a larger programmable device. Typical uses include interface decoding, industrial control panels, test fixtures, programmable logic controllers, peripheral glue logic, and compact state-machine implementations. In a control panel, the ATF22LV10C-15XC could implement switch decoding, status encoding, and discrete sequencing functions while retaining flash-based field programmability. In a test fixture, it can combine multiple address-decoding and control functions into one low-power package. PCB design should account for the device’s 24-pin TSSOP geometry, programming interface requirements, and decoupling needs. Place the device close to the signals it serves to minimize trace lengths and routing complexity. When power management is important, verify that the power-down input sequencing and external logic do not create an uncontrolled state during startup or reset. This product page combines the manufacturer’s device specifications with application-oriented design guidance and a pin-compatible alternative table. It is intended to help engineers evaluate logic density, propagation-delay class, package compatibility, reprogrammability, and low-power operation before integrating the ATF22LV10C-15XC into a compact embedded design.
ATF22LV10CQZ-30JC - 30ns 10-Macrocell EE PLD | Microchip
The Microchip Technology ATF22LV10CQZ-30JC is a 30 ns, 10-macrocell electrically erasable programmable logic device with electrically erasable flash memory, a 3.0 V to 5.5 V operating supply range, and a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. The ATF22LV10CQZ family combines a simple programmable logic architecture with low-voltage operation and edge-sensing zero standby power. A simple programmable logic device, or SPLD, is a user-programmable digital logic component within the broader programmable-logic-device and semiconductor hierarchy. It combines AND-array logic, programmable OR-array logic, input registers, and output registers into a compact device for implementing fixed control, decoding, interface, and glue-logic functions. Electrically erasable flash memory allows the configuration to be rewritten without removing the package from its circuit board. The principal operating characteristics of the ATF22LV10CQZ-30JC include 10 macrocells, a 30 ns speed grade, operation from 3.0 V to 5.5 V, and a 28-pin PLCC package. The Microchip ATF22LV10CQZ family supports speeds down to 25 ns, and its edge-sensing circuitry can place the CQZ version into a zero standby-power mode when the device is idle. The manufacturer datasheet lists 3 uA typical standby current for the ATF22LV10CQZ version. These characteristics suit systems that need reconfigurable compact logic without using a larger FPGA or microcontroller. The ATF22LV10C architecture uses 10 macrocells to implement sum-of-products combinational or registered logic functions. Registered outputs can be selected through the device programming configuration, allowing registered versus combinational behavior to be assigned on a macrocell basis. Input transition detection provides the low-power operating behavior associated with the CQZ family, while the pin-keeper feature helps retain input states when necessary. Configuration data is stored in electrically erasable flash memory for repeated in-circuit updates. Typical uses include industrial control logic, peripheral decoding, bus-interface arbitration, data-format conversion, embedded timing sequences, and compact system-control functions. The 3.0 V minimum operating voltage supports low-voltage systems, while operation to 5.5 V provides design flexibility for mixed-voltage equipment. A 30 ns propagation-delay grade is appropriate for control paths that do not require the fastest 25 ns ATF22LV10CQZ option. Designers should account for the PLCC footprint and verify the exact pin assignment, programming file, and power-down behavior before replacing an existing ATF22LV10CQZ-30JC. Because flash-programmed logic has setup, programming, and system-power requirements, use the manufacturer programming and application guidance rather than treating the device as a conventional mask-programmed PAL. Keep supply and ground connections compact and follow the datasheet decoupling recommendations. This product summary combines the manufacturer electrical characteristics with distributor package data, usable replacement guidance, and application-focused design notes. It helps engineers identify the ATF22LV10CQZ-30JC as a 28-PLCC, 10-macrocell, 30 ns programmable logic option when planning upgrades, legacy-product maintenance, and reconfiguration of compact control logic.
ATF22LV10CQZ-30JU - 30ns 10-Macrocell EEPLD | Microchip
The Microchip Technology ATF22LV10CQZ-30JU is a high-performance CMOS electrically erasable programmable logic device with 10 macrocells, 10 user I/O pins, a 30 ns speed grade, and a 28-pin PLCC package. It operates across a 3.0 V to 5.5 V supply range and supports industrial and commercial temperature grades. A simple programmable logic device, or SPLD, is a semiconductor that implements fixed Boolean logic through user-programmed fuse or memory elements. In the broader hierarchy, the ATF22LV10CQZ-30JU belongs to programmable logic devices, programmable logic arrays, digital logic ICs, and integrated circuits. Its electrically erasable flash-memory configuration permits reprogramming without a dedicated external programmer. The principal benefits include 10 macrocells for implementing sum-of-products logic, a 30 ns propagation-delay grade, 10 configurable user I/O pins, and operation from 3.0 V to 5.5 V. The manufacturer identifies the family as supporting speeds down to 25 ns, with each speed grade specified over the full 3.0 V to 5.5 V range. Edge-sensing zero standby power further reduces active supply demand to 3 uA typical when the power-down function is asserted. ATF22LV10CQZ-30JU combines a 22V10 architecture with electrically erasable flash memory. The 10 macrocells provide dedicated product-term logic and programmable output routing for control, decoding, address translation, interface conditioning, and fixed Boolean functions. Because the device supports both 3.3 V and 5 V supply environments, designers can standardize a board platform across mixed industrial and commercial voltage levels, although each design must retain the required input and output operating constraints. Typical uses include industrial control logic, data-acquisition interface decoding, display and instrument control, peripheral address decoding, and embedded system glue logic. The ATF22LV10CQZ-30JU is especially useful when a small amount of deterministic Boolean logic is needed but a microcontroller or FPGA would add unnecessary cost, software complexity, or board area. The 28-pin PLCC package also supports legacy industrial boards with through-hole-style J-lead geometry. Designers should verify every pin assignment in the manufacturer pin-description table before laying out a replacement PCB. Input and output pins are multiplexed through the SPLD architecture, so changing a programmed macrocell or output polarity can alter signal behavior even when the physical package remains unchanged. Power-down, reset, clock, and I/O direction decisions should be made before programming the device. This product page combines the Microchip family specifications with practical replacement guidance, package-aware comparisons, and design notes for programming, logic partitioning, power behavior, and legacy-system integration. These engineering details help determine whether the ATF22LV10CQZ-30JU can reuse an existing PCB and preserve the intended timing and logic behavior.
ATF22LV10CQZ-30PC - 30ns 500-Gate SPLD | Microchip Technology
Microchip Technology ATF22LV10CQZ-30PC is a high-performance CMOS simple programmable logic device with 500 programmable gates, 10 macrocells, a 30 ns speed grade, and a 3.0 V to 5.5 V operating supply range. The device is packaged in a 24-pin PDIP and uses electrically erasable flash memory for nonvolatile configuration storage. A simple programmable logic device, or SPLD, is a user-programmable digital semiconductor used to combine Boolean equations, counters, decoders, state machines, and control logic in one compact component. Structurally, an SPLD sits between fixed logic and a field-programmable gate array. Its macrocell architecture provides a practical way to consolidate small control functions without using a microcontroller or a larger FPGA. The ATF22LV10CQZ family supports speed grades down to 25 ns and operates from 3.0 V to 5.5 V for industrial and commercial temperature ranges. Its 30 ns grade is intended for designs requiring a defined propagation-delay class rather than the highest speed available in the family. The electrically erasable flash configuration retains the implemented logic when power is removed and supports in-circuit reprogramming. The ATF22LV10CQZ also includes edge-sensing standby behavior. According to the Microchip manufacturer datasheet, the device provides typical 3 µA zero standby power when the power-down input is active. When the power-down feature is not used, the device operates in a full-power low-voltage mode. These operating characteristics make the part suitable for mixed-voltage control equipment where low static consumption and nonvolatile logic configuration are useful. Typical applications include industrial control, interface decoding, sequencers, legacy peripheral emulation, programmable timing, and embedded control support. The 24-pin PDIP package also simplifies inspection, prototyping, socket-based maintenance, and through-hole assembly where a surface-mount footprint is unnecessary. The device can implement several Boolean functions around a common input and output structure, reducing discrete gate count in compact legacy systems. Designers should verify timing against the 30 ns speed grade and the external circuit delays that contribute to the complete system path. Power-down behavior, supply sequencing, and unused input pins should be handled according to the manufacturer datasheet. Because the 24-pin PDIP footprint is through-hole, board layout must preserve adequate spacing and mechanical clearance around the device. This page organizes the available manufacturer and distributor information into a technical product record, including device functionality, obsolete-lifecycle information, same-package alternatives, application guidance, and design considerations. These engineering notes help shorten legacy-support and obsolescence-management work while keeping the underlying manufacturer documentation as the final authority for programming and electrical limits.
ATF22LV10CQZ-30PI - 30ns 22V10 PLD | Microchip Technology
The Microchip Technology ATF22LV10CQZ-30PI is a 22V10 electrically erasable programmable logic device with 10 macrocells, a 30 ns speed grade, and 24-PDIP packaging. It operates across a 3.0 V to 5.5 V supply range and combines 500 gates of CMOS logic with nonvolatile electrically erasable flash memory. The industrial-temperature designation identifies its intended operating class, while the QZ package suffix identifies the 24-pin PDIP configuration. A simple programmable logic device, or SPLD, is a user-programmable digital logic component within the broader field of programmable logic devices. Its internal macrocells can be interconnected to implement Boolean equations, decoding, control logic, and state-machine functions. Electrically erasable flash memory allows the configuration to be retained while supporting reprogramming, making the ATF22LV10CQZ suitable for small control-logic blocks that do not justify a larger CPLD or FPGA. The ATF22LV10CQZ family supports propagation delays down to 25 ns across its speed grades. This particular -30PI configuration provides a 30 ns grade for industrial-temperature operation. The 3.0 V to 5.5 V operating range supports both 3.3 V and 5 V system rails, while the 10-macrocell architecture provides 500 gates of logic capacity. A dedicated power-down feature can place the device into zero standby power-down mode, reducing consumption when the associated logic is inactive. Internally, the ATF22LV10CQZ is a high-performance CMOS programmable logic device using electrically erasable flash memory for configuration storage. The macrocell-based architecture provides a practical balance between logic density, predictable timing, and simple device programming. Because flash configuration is nonvolatile, the programmed function remains available after power removal without requiring an external configuration PROM or continuous SRAM refresh. Typical applications include industrial control, interface decoding, counter and timer logic, instrumentation, embedded system control, and legacy peripheral emulation. The 24-PDIP package is especially useful for prototypes, test fixtures, and systems assembled through through-hole assembly. It may also fit repaired or legacy boards that specifically require the ATF22LV10CQZ 24-pin footprint and its documented 3.0 V to 5.5 V interface. When designing around this device, confirm that the board uses the 24-pin PDIP pinout and that the programmed pin configuration matches the target application. Avoid changing the device type, supply voltage, or temperature designation without reviewing the manufacturer datasheet for pin-level and timing differences. The power-down pin should be driven only in a sequence compatible with the surrounding logic to prevent unintended state transitions during startup. This product page combines the manufacturer device specifications, verified package and speed information, practical selection guidance, same-footprint alternatives, and design-focused implementation notes. It also distinguishes the industrial -30PI ordering code from commercial-temperature and different-package variants that may otherwise appear similar in broad PLD searches.
ATF22LV10CQZ-30SU - 30ns 500-Gate PLD | Microchip Technology
The Microchip Technology ATF22LV10CQZ-30SU is a high-performance CMOS simple programmable logic device with 500 gates, 10 macrocells, 10 I/O pins, and a 30 ns propagation delay, supplied in a 24-pin SOIC package. It operates across a 3.0 V to 5.5 V supply range and supports low-voltage operation with an edge-sensing zero-standby-power feature that draws 3 µA typical when the power-down function is active. A simple programmable logic device, or SPLD, is a user-programmable semiconductor that replaces a collection of conventional AND, OR, and flip-flop logic gates. The ATF22LV10CQZ belongs to the broader programmable-logic-device hierarchy, combining nonvolatile configuration storage with combinational and registered logic functions. Its electrically erasable flash memory allows the programmed configuration to be retained and electrically updated during development or production. The principal features of the ATF22LV10CQZ-30SU include a 30 ns speed grade, 500 logic gates, 10 macrocells, and operation from 3.0 V to 5.5 V. Edge-sensing zero-standby-power operation reduces current consumption when the power-down pin is asserted. The 24-pin SOIC package provides a surface-mount option for compact control, decoding, interface, and glue-logic designs while supporting both 3.3 V and 5 V systems. Microchip describes the ATF22LV10CQZ family as a high-performance CMOS programmable logic device using proven electrically erasable flash memory. The family supports speeds down to 25 ns, while the ATF22LV10CQZ-30SU is the 30 ns ordering option. Its supply-voltage range accommodates industrial and commercial equipment, and its zero-power mode is useful in systems where the PLD must remain connected to an unpowered or minimally powered domain without continuous static drain current. Typical uses include bus decoding, control-signal generation, state-machine implementation, peripheral interfacing, display sequencing, audio-system control, and compact industrial automation modules. In each case, the device consolidates multiple fixed-logic functions into one programmable package and can simplify a design when changing control logic would otherwise require a board respin. The ATF22LV10CQZ-30SU is also suitable for legacy product maintenance because its established architecture and SOIC footprint support targeted replacements in existing equipment. Designers should account for setup and hold timing, output enable behavior, clock requirements, and the voltage tolerance of connected signals. Place decoupling capacitors close to the supply pins, preserve the recommended transition-time network, and use the power-down input only after confirming that all outputs will tolerate the resulting high-impedance state. Programming must follow the manufacturer’s device and programmer requirements to preserve the stored configuration reliably. This product page organizes the ATF22LV10CQZ-30SU specifications, verified sourcing information, compatible ordering variants, and practical selection guidance into one engineering reference. It also distinguishes direct SOIC drop-in options from package-incompatible alternatives and identifies the operating details that must be confirmed before replacing an existing PLD in a live design.
ATF22LV10CZ-25JC - 25ns 10-Macrocell PLD | Microchip
The Microchip ATF22LV10CZ-25JC is a high-performance electrically erasable CMOS programmable logic device with 10 macrocells, approximately 500 logic gates, a 25 ns propagation delay, and operation from 3.3 V to 5 V. The device is offered in a 28-pin J-lead PLCC package measuring 11.51 mm by 11.51 mm. It combines erasable Flash memory with a simple PLD architecture for compact glue-logic, control, decoding, and interface designs. A simple programmable logic device is a semiconductor that stores a fixed logic function in nonvolatile memory and implements it through configurable AND-array and OR-array connections. Within the broader hierarchy, an SPLD is a programmable logic device, which is a form of digital integrated circuit and logic IC. The ATF22LV10CZ series provides a practical middle ground between individual gates and more complex programmable logic arrays. The ATF22LV10CZ-25JC provides 10 macrocells, a nominal 25 ns speed grade, 3.3 V and 5 V operation, and standby current of no more than 25 microamperes. Input and output keeper circuits retain previous logic levels while inputs and outputs are idle, eliminating the static current normally consumed by external pull-up resistors. These features support compact designs where deterministic state retention and low standby consumption are important. At the device level, the electrically erasable Flash configuration allows the logic design to be reprogrammed without a dedicated programmer that uses ultraviolet erasure. The 25 ns speed grade is suited to control paths and moderate-speed interface logic rather than high-frequency synchronous datapaths. Designers should also account for the output-delay and setup requirements of the specific system clock when evaluating timing closure. Typical uses include bus decoding, address and chip-select logic, sequencer control, interface arbitration, legacy peripheral adaptation, and small state-machine implementations. The device is especially useful in industrial, communications, and embedded-control equipment where compact fixed logic can reduce component count while remaining electrically erasable. The principal design consideration is the 28-pin PLCC footprint. PLCC sockets remain practical for prototype and legacy maintenance work, but modern production boards may favor surface-mount packages, so mechanical availability should be checked before a new design begins. The manufacturer datasheet should be used for the complete pin description, timing limits, recommended operating conditions, and programming procedure. This page combines the ATF22LV10CZ-25JC device identity, package information, verified engineering characteristics, candidate pin-compatible alternatives, and practical implementation guidance in one design-focused reference. It also distinguishes speed-, temperature-, and supply-related differences so engineers can assess replacement risk before modifying an existing PCB.
ATF22LV10CZ-25JI - 10-Macrocell 25ns EEPLD | Microchip Technology
The Microchip Technology ATF22LV10CZ-25JI is a 10-macrocell electrically erasable programmable logic device with 500 gates, 25 ns propagation delay, and 3.3 V or 5 V operation in a 28-pin PLCC package. It provides a compact implementation of fixed programmable logic functions while retaining nonvolatile configuration memory. An EEPLD is an electrically erasable programmable logic device, a member of the programmable-logic-device hierarchy. Unlike a mask-programmed custom gate array, an EEPLD can be configured for a specific Boolean function after manufacture. Its macrocell-based architecture consolidates repeated logic patterns into reusable structures, making the device suitable for control, decoding, interface, and glue-logic functions where changing a programmed design is more convenient than fabricating a custom ASIC. The ATF22LV10C family supports 3.0 V to 5.5 V operation and 10 macrocells organized around 500 gates. The -25 speed designation identifies a 25 ns propagation-delay grade, while the J suffix identifies the industrial-temperature ordering option. Its 28-PLCC surface-mount package provides a leaded alternative to the smaller 24-pin DIP arrangement and supports compact board layouts where a through-hole PLD is required. Technically, the ATF22LV10C combines combinational and registered logic resources within an electrically erasable CMOS architecture. The high-performance EEPROM configuration memory preserves the implemented logic after power removal, allowing firmware or board-level programming to define the device rather than a permanent mask set. Speed grades are specified across the 3.0 V to 5.5 V supply range, allowing one device family to serve both conventional 5 V and lower-voltage 3.3 V systems when timing and output constraints are satisfied. Typical uses include legacy industrial control, alarm and sequencing logic, instrumentation, peripheral decoding, and board-level interface glue. The 25 ns grade is appropriate where propagation delay remains below the system timing budget, while its 10-macrocell capacity limits larger designs to compact Boolean functions or modest state-machine implementations. Engineers should also account for the age of the architecture when selecting signal levels, programming tools, and modern system integration requirements. For PCB implementation, preserve the manufacturer's PLCC footprint, provide unobstructed access to programming or test connections, and verify every signal against the pin-description table in the manufacturer datasheet. Power-supply decoupling and input-signal transition requirements should be implemented using the recommended circuit values rather than generic assumptions, especially when unused inputs and outputs are connected. This product page consolidates the exact ordering information, verified family-level specifications, sourcing guidance, and practical implementation considerations for the ATF22LV10CZ-25JI. It also distinguishes true same-footprint alternatives from related ATF22LV10C variants whose speed grade, temperature grade, or package differs.
ATF22LV10CZ-25PC - 500 Gate, 25ns EE PLD | Microchip
The Microchip ATF22LV10CZ-25PC is a 500-gate electrically erasable programmable logic device with 10 macrocells, a 25 ns propagation delay, and 3.3 V to 5 V operation in a 24-pin PDIP package. It combines CMOS logic with electrically erasable Flash memory so stored configurations can be reprogrammed without removing the device from the circuit. A programmable logic device is a programmable semiconductor that implements combinational or registered logic functions using a structured array of AND and OR terms. The ATF22LV10 series belongs to the simple PLD category, positioned below complex PLDs and FPGAs for compact designs requiring modest gate capacity, straightforward architecture, and a small package footprint. The ATF22LV10CZ-25PC provides 10 macrocells and approximately 500 gates of logic capacity. Its 25 ns speed grade targets control, interface, decoding, and glue-logic functions where cycle-by-cycle performance is sufficient. Operation from 3.3 V to 5 V allows the same design to operate in modern 3.3 V systems or legacy 5 V equipment. The electrically erasable Flash configuration supports in-circuit reprogramming and eliminates one-time-programmable device constraints. Its zero-power operating mode reduces consumption when the logic device is inactive, while the manufacturer datasheet specifies a maximum standby current of 25 uA. The ATF22LV10CZ/CQZ family is based on proven electrically erasable Flash technology and is intended for designs requiring deterministic combinational logic, registered outputs, and reconfigurable control paths without the resource overhead of an FPGA. Typical applications include industrial control and data-acquisition equipment, legacy peripheral expansion, address decoding, programmable timer and counter logic, instrument front panels, embedded system interfaces, and small embedded controllers. The 24-pin PDIP package also supports prototyping and through-hole industrial assemblies where a socketed or hand-inserted device is convenient. When designing around this PLD, verify the required output timing against the 25 ns speed grade and confirm that the board supplies a voltage within the 3.3 V to 5 V operating range. Because the configuration memory is Flash-based, the same fitted device can be rewritten, although programming procedure, logic equations, and state behavior still require careful verification. This page organizes the device architecture, pin-package constraints, verified alternatives, and practical engineering considerations into one engineering reference. It also distinguishes true same-footprint options from surface-mount variants that require PCB footprint changes before they can be considered drop-in replacements.
ATF22LV10CZ-25PI - 25ns 10-Macrocell Flash PLD | Microchip
The Microchip Technology ATF22LV10CZ-25PI is an electrically erasable CMOS programmable logic device with 10 macrocells, approximately 500 logic gates, and a 25 ns propagation delay. It operates across a 3.0 V to 5.5 V supply range and is packaged for legacy through-hole systems in a 24-pin PDIP format. A simple programmable logic device, or SPLD, is a programmable-logic IC that combines a fixed collection of AND-array and OR-array logic resources with user-programmable configuration data. Within the broader hierarchy, an SPLD is a programmable logic device, a form of digital logic IC, and a member of the semiconductor family used for control, decoding, interface, and fixed-function logic implementation. Unlike a microcontroller or DSP, its principal role is deterministic combinational and registered logic rather than software-driven sequential processing. The ATF22LV10CZ-25PI provides 10 macrocells and approximately 500 gates in a 24-pin PDIP package. Its 25 ns speed grade supports moderate timing requirements, while its electrically erasable Flash configuration allows a device to be programmed, erased, and reused without a separate UV-erasable memory process. The manufacturer datasheet identifies operation from 3.0 V to 5.5 V and a maximum standby current of 25 µA. Technically, the CZ/CQZ family combines CMOS logic with electrically erasable Flash memory and keeper circuits on input and output pins. Keeper circuits preserve previous logic states during idle periods, reducing the static power otherwise required by external pull-up resistors. This characteristic is useful in designs where many PLD inputs may remain inactive for extended periods and where predictable power behavior matters. Typical uses include industrial control decoding, legacy peripheral interfacing, programmable address and command decoding, compact glue-logic implementation, and retrofit maintenance of equipment that already uses a 24-pin PDIP footprint. Because the ATF22LV10CZ-25PI is a Flash-based SPLD, it is particularly suitable for prototypes and production systems requiring field-reconfigurable logic without relying on one-time-programmable devices. The principal design consideration is supply compatibility. Although the device supports operation down to 3.0 V, the surrounding legacy circuit may use 5 V logic, and input and output levels must be checked against the manufacturer specifications. Programming should follow the official ATF22V10C-family procedure, including correct supply sequencing, interface timing, and device configuration checks. This product record combines the device architecture, package information, electrical characteristics, drop-in candidates, application guidance, and engineering considerations needed to evaluate an ATF22LV10CZ-25PI for an existing 24-pin PDIP design.
ATF22LV10CZ-25SC - 500-Gate 25ns SPLD | Microchip Technology
The Microchip Technology ATF22LV10CZ-25SC is a 500-gate electrically erasable simple programmable logic device with 10 macrocells, a 25 ns propagation speed, and a 3.3 V to 5 V supply range. The device is packaged in a commercial-temperature, 24-pin plastic SOIC package. It combines programmable Boolean and registered logic in a compact device intended for control, decoding, address mapping, and interface logic. A simple programmable logic device, or SPLD, is a semiconductor that implements a fixed collection of AND-array, OR-array, and programmable I/O resources. In the system hierarchy, an SPLD belongs to programmable logic devices, which sit between fixed logic gates and larger programmable logic arrays. The ATF22LV10C architecture is suited to compact designs requiring modest logic density, flexible I/O assignments, and electrical reconfiguration without changing the PCB. The ATF22LV10CZ-25SC provides 10 macrocells and approximately 500 gates of programmable logic. Its 25 ns speed grade supports moderate clock rates and control paths, while 3.3 V to 5 V operation accommodates common industrial and embedded logic levels. The device is specified in the 24-SOIC package for surface-mount assembly, providing a small footprint for legacy and cost-sensitive control boards. The Z designation identifies the electrically erasable implementation in the ATF22LV10C family, and the -25 suffix denotes the 25 ns speed grade. The SC package suffix identifies the commercial-temperature SOIC configuration. This combination favors designs that require deterministic combinational or registered logic but do not need the larger gate capacity of a complex PLD. Typical uses include industrial control and instrumentation, legacy peripheral interface logic, programmable command decoding, keypad and display scanning, counter and state-machine implementation, and compact embedded system support functions. Because the device supports electrical erasure, firmware or configuration logic can be updated during manufacturing, test, or maintenance rather than requiring a new programmed device for every logic revision. PCB design should preserve the device's documented supply and grounding arrangement and route programming, clock, feedback, and I/O signals according to the manufacturer pin description. Confirm voltage compatibility before connecting it to 5 V systems because input and output limits are device-specific. Use the manufacturer programming specification to verify supported algorithms, fuse handling, and approved third-party programmers. This product page combines the device architecture, package characteristics, verified sourcing references, and practical selection guidance with same-family drop-in alternatives. It also highlights the differences between speed, temperature, and package variants so engineers can migrate an existing ATF22LV10 design without overlooking operating conditions or programmer requirements.
ATF22LV10CZ-25SI - 3.3V 10-Macrocell PLD | Microchip
The Microchip Technology ATF22LV10CZ-25SI is a 3.3 V electrically erasable programmable logic device with 10 macrocells, a 25 ns propagation delay, and a 24-SOIC package. It uses CMOS electrically erasable Flash memory technology and is designed for compact logic implementation where a small macrocell count and in-circuit reprogrammability are valuable. The industrial-temperature suffix identifies this version for industrial equipment, while the 24-SOIC package supports conventional surface-mount PCB assembly. A programmable logic device, or PLD, is a semiconductor whose internal logic connections are user-programmable. The ATF22LV10 belongs to the 22V10 family and sits below field-programmable gate arrays in implementation complexity: a design can be consolidated into 10 macrocells without developing a mask-programmed ASIC. Within the semiconductor hierarchy, it is a programmable logic IC within the broader integrated-circuit and digital-semiconductor categories. The main operating characteristics include 10 available macrocells, a nominal 25 ns device speed designation, and standby current rated at no more than 25 µA. Electrically erasable Flash memory permits the programmed configuration to be erased and rewritten during development or production. These attributes make the device useful for address decoding, control logic, state sequencing, interface glue, and compact combinational or sequential functions. The ATF22LV10CZ uses a 3.3 V supply and retains the familiar 22V10 logic organization. Its 24-SOIC outline provides enough I/O for externally presented inputs and outputs while keeping the package compatible with established 24-pin surface-mount layouts. The electrically erasable configuration memory distinguishes it from older one-time-programmable or mask-programmed implementations, allowing the same physical device type to support firmware and logic revisions. Typical uses include industrial controller address decoding, peripheral interface control, programmable command sequencing, and compact digital signal-processing support logic. The 10-macrocell limit is appropriate when a design requires more flexibility than a fixed gate or comparator but less capacity than a larger CPLD or FPGA. System partitioning should reserve external logic or a larger programmable device when required input, output, or macrocell counts exceed the device limits. PCB design should follow the manufacturer pin description and recommended decoupling guidance rather than inferring connections from a generic 24-pin footprint. Place the input bypass capacitor close to the supply pins, route programming and control signals away from sensitive analog paths, and confirm that exposed PCB pads and assembly processes are compatible with the 24-SOIC outline. Device selection should also verify system timing against the 25 ns speed designation. This product page combines the device identity, package information, technical characteristics, practical application guidance, and validated replacement considerations in one engineering-focused reference. It helps engineers identify the ATF22LV10CZ-25SI, confirm its 3.3 V 10-macrocell feature set, review the 24-SOIC footprint, and determine whether a temperature-grade or package-compatible family member is appropriate for a redesign.