Logic ICs
بەرهەمەکان (720+)
ATF22V10B-15JC - 10-Macrocell 15ns EE PLD | Microchip Technology
The Microchip Technology ATF22V10B-15JC is a high-performance CMOS electrically erasable programmable logic device (EE PLD) with 10 macrocells, 20 inputs, and 10 outputs, designed for logic implementation in embedded and industrial control systems. The device is speed-rated at 15 ns and operates from a 5 V supply, with the ATF22V10B family supporting speeds down to 7.5 ns and power dissipation as low as 10 mA. It is packaged in a 28-pin PLCC surface-mount package measuring approximately 11.51 mm by 11.51 mm. An electrically erasable PLD is a programmable logic device that stores its configuration in nonvolatile EEPROM or Flash memory and can be reprogrammed in the field. The ATF22V10B belongs to the simple PLD hierarchy, where configurable macrocells implement sum-of-products logic functions. Compared with a fixed gate array or a fully programmable FPGA, this device provides a compact, lower-complexity solution for glue logic, control decoding, state-machine sequencing, and interface conditioning. The ATF22V10B-15JC provides a 15 ns propagation-delay grade, 10 macrocells, 20 input pins, and 10 output pins. Its electrically erasable Flash memory technology supports reprogramming, while the device is manufactured using a high-reliability CMOS process. The family is designed for commercial, industrial, and military temperature options, with speed grades specified over a 5 V plus-or-minus 10 percent supply range for military and industrial grades and 5 V plus-or-minus 5 percent for other applicable grades. The 28-pin PLCC package offers a practical surface-mount alternative to older through-hole PLD packages. Its configuration memory retains programmed logic across power cycles, allowing the device to serve as a standalone logic controller. The registered inputs and outputs provide predictable timing for control logic, and the device's macrocell architecture makes it suitable for designs that require more flexibility than a PAL but less routing and configuration complexity than an FPGA. Typical uses include industrial automation controllers, legacy equipment interfaces, programmable relay logic, instrument control panels, embedded sequencing, and board-level adaptation between fixed digital functions. In these applications, the ATF22V10B-15JC can consolidate multiple gates, counters, decoders, and state-transition logic into one configurable device while reducing the number of separate logic ICs required. When designing around this PLD, verify the power-supply tolerance, output-drive requirements, and timing budget against the system clock. Program the device with the appropriate Atmel or Microchip programming tool, and use the manufacturer pin description and programming guidance when assigning board functions. This page combines device specifications, package details, drop-in alternatives, application guidance, and practical design considerations for engineers maintaining or redesigning legacy programmable-logic boards.
ATF22V10B-15PC - 10-Macrocell 15 ns Flash PLD | Microchip
The Microchip ATF22V10B-15PC is a high-performance CMOS electrically erasable programmable logic device with 10 macrocells, a 500-gate-equivalent architecture, and a 15 ns speed grade in a 24-pin PDIP package. It uses reprogrammable Flash technology, operates from a nominal 5 V supply, and combines a 20-year data-retention specification with as many as 100 erase/write cycles. A programmable logic device is a user-programmable semiconductor that replaces several discrete gates, counters, decoders, and state machines with one configurable integrated circuit. The ATF22V10B belongs to the simple PLD hierarchy, where each of its 10 macrocells implements a sum-of-products logic function through configurable AND and OR structures. This places the device below CPLDs and FPGAs in general complexity while providing nonvolatile, field-reprogrammable logic. The ATF22V10B family supports programming speeds down to 7.5 ns, although the ATF22V10B-15PC is the 15 ns grade identified by its part-number suffix. Reported power dissipation can be as low as 10 mA. The device is reprogrammable, is described as 100% tested, and includes 2,000 V ESD protection and 200 mA latchup immunity. These characteristics suit control, decoding, address translation, and legacy interface logic that must retain its configuration when power is removed. The ATF22V10B architecture is organized around 10 PAL-style macrocells. Each macrocell can combine multiple product terms, allowing compact implementations of common combinational and sequential functions. Unlike a mask-programmed PAL device, the electrically erasable Flash configuration permits the same physical device to be reprogrammed during development or field updates. The family also includes military, commercial, and industrial temperature options, with speed ranges characterized across their respective supply conditions. Typical uses include legacy bus-interface decoding, printer and copier control, industrial automation, embedded control-interface translation, and small state machines. Its 24-pin PDIP format is useful for prototypes, legacy motherboard designs, and equipment where socketed or through-hole assembly is preferred. For new high-density or high-speed designs, an FPGA or CPLD may provide more routing flexibility, but the ATF22V10B-15PC remains useful when its 10-macrocell architecture is sufficient. Designers should follow the pin-connection and programming guidance in the manufacturer datasheet, preserve adequate supply decoupling, and account for the 15 ns speed grade when evaluating address-decoder or control-path timing. A conventional 24-pin DIP footprint should not be assumed equivalent to every 24-pin PLD without checking pin functions, power rails, programming interface connections, and output behavior. This page combines device specifications, practical replacement guidance, package-level comparison, and design guidance for engineers evaluating the ATF22V10B-15PC. It also distinguishes directly relevant 24-pin alternatives from related devices whose temperature grade, qualification, speed, or package may prevent a true drop-in substitution.
ATF22V10B-15SC - 15 ns 10-Macrocell EE PLD | Microchip
The Microchip Technology ATF22V10B-15SC is a 5 V, 15 ns electrically erasable programmable logic device with 10 macrocells in a 24-pin SOIC package. It combines a CMOS PLD with electrically erasable flash-memory technology, making it suitable for compact control, decoding, multiplexing, and fixed-logic implementations. The device is identified as a 22V10-family EE PLD, and the -15 speed grade supports operation up to 15 ns. Its 24-SOIC package measures approximately 0.295 inch, or 7.50 mm, in width and uses surface mounting. An electrically erasable programmable logic device, or EE PLD, is a programmable-logic semiconductor whose configuration is stored in nonvolatile electrically erasable memory. Within the broader hierarchy, an EE PLD is a form of PLD, which belongs to the broader logic-IC and semiconductor families. Unlike a one-time-programmable fuse-based device, electrically erasable technology allows the logic configuration to be erased and reprogrammed during development, production, or field maintenance. This makes the ATF22V10B useful where engineering changes or reusable configurable logic are valuable. The ATF22V10B family supports speed grades down to 7.5 ns, while the ATF22V10B-15SC provides a 15 ns grade. The manufacturer identifies the underlying ATF22V10B as a high-performance electrically erasable CMOS PLD using proven electrically erasable flash-memory technology. The commercial speed range is specified at 5 V ±5%, while military and industrial ranges use the wider 5 V ±10% operating-voltage range. The listed low-power operating point can be as low as 10 mA. With 10 macrocells, the ATF22V10B-15SC implements Boolean logic, state-machine behavior, address decoding, interface conditioning, and control functions without requiring a separate microcontroller. The 15 ns grade favors designs in which deterministic combinational and registered logic is more important than very high I/O throughput. Its nonvolatile configuration also permits field updates without supplying power during storage. Typical uses include industrial control and instrumentation, legacy equipment upgrades, peripheral-interface decoding, programmable switch logic, test fixtures, and small embedded control systems. The ATF22V10B-15SC is particularly suitable when a compact SOIC footprint, electrical reconfiguration, and straightforward fixed-logic implementation are more useful than the software flexibility of a microcontroller or FPGA. Designers should use the manufacturer datasheet pin-description table when assigning PCB signals and confirm operating-voltage, timing, output-drive, and temperature limits against the selected grade. Input and output paths also require normal CMOS decoupling and signal-integrity practices, especially when external signals drive the configurable I/O paths. This page combines the manufacturer device information, lifecycle and package findings, drop-in alternatives, application guidance, and engineering-focused comparisons. It adds practical selection context and design notes while keeping the device-specific facts tied to the manufacturer datasheet and product information.
ATF22V10BQ-15SI - 10-Macrocell 15ns PLD | Microchip
The Microchip Technology ATF22V10BQ-15SI is a 10-macrocell, electrically erasable CMOS programmable logic device with a 15 ns speed grade, supplied in a 24-pin SOIC package. It belongs to the ATF22V10B family of simple PLDs and stores its logic configuration in electrically erasable Flash memory. The device measures 0.295 inches, or 7.50 mm, in body width and is intended for surface-mount assembly. A programmable logic device, or PLD, is a semiconductor whose digital logic behavior is defined by a user configuration rather than a fixed circuit. The ATF22V10B combines a compact 22V10 architecture, 10 macrocells and configurable I/O in the same package. Its position within the logic hierarchy—configurable PLD, digital logic IC and semiconductor—makes it useful for implementing compact control, decoding, multiplexing and interface logic without relying on a larger programmable device. Key device characteristics include a 15 ns propagation-speed designation, 10 macrocells, electrically erasable Flash configuration memory and a 24-SOIC package. The ATF22V10B family is specified at a nominal 5 V supply, with the manufacturer documenting 5 V ±10% ranges for military and industrial temperature grades and 5 V ±5% for the relevant commercial range. These operating conditions make supply tolerance and logic-level compatibility central to implementation. The electrically erasable architecture allows a device to be reconfigured without a dedicated programmer that erases only one-time-programmable cells. This supports design revisions, production programming and reusable control logic. However, the device is a simple PLD rather than a FPGA: its 10 macrocells are intended for compact combinational and registered logic, and complex system-level control is better handled by a programmable logic device with more resources. Typical uses include industrial control interfaces, decoder and mux structures, pulse and timing qualification, alarm and interlock logic, test-fixture control and compact legacy system interfaces. The 24-pin SOIC package also makes the ATF22V10BQ-15SI suitable for designs requiring conventional surface-mount assembly rather than a large programmable-logic package. Designers should verify supply tolerance, input thresholds, output drive, timing constraints and programming-device compatibility against the manufacturer datasheet before releasing a PCB. Decoupling and signal-integrity practices remain necessary even for a small PLD: place the supply capacitor close to the device, preserve the required clock and control routing, and use the package pin-definition table when assigning board signals. This product record combines the device architecture, package characteristics, verified alternatives and application-oriented engineering guidance. It also identifies practical selection limits so engineers can distinguish a true same-footprint replacement from a PLD that is only functionally similar.
ATF22V10BQL-20JC - 20ns Flash PLD | Microchip Technology
The Microchip Technology ATF22V10BQL-20JC is a 22V10 electrically erasable CMOS programmable logic device with 10 macrocells, approximately 500 gates, and a 20 ns speed grade in a 28-pin PLCC package. It operates from a nominal 5 V supply and uses electrically erasable Flash memory for in-circuit reprogramming. The device is designed for compact logic control, interface decoding, state-machine implementation, and replacement of conventional GAL-type combinational or registered logic. A simple programmable logic device, or SPLD, is a programmable-logic-device category within the broader integrated-circuit hierarchy. SPLDs combine AND-array and OR-array logic into a small number of macrocells. Compared with a mask-programmed PLD, an electrically erasable SPLD permits design revisions without changing the integrated circuit or PCB artwork. The ATF22V10B therefore supports prototype iteration, field upgrades, and configurable control logic in systems where gate count and propagation delay are more important than very high I/O density. The ATF22V10B family provides reprogrammable Flash configuration, 100% tested high-reliability CMOS circuitry, and 20-year data retention. The manufacturer lists operating speeds down to 7.5 ns across the family, while the ATF22V10BQL-20JC suffix identifies the 20 ns commercial-temperature configuration. Power dissipation can be as low as 10 mA in the family description. The device also includes 2,000 V ESD protection and 200 mA latch-up immunity according to the family datasheet information. Technically, the ATF22V10B combines ten configurable macrocells with Flash-programmed logic equations. This architecture allows each macrocell to participate in sum-of-products logic, registered state-machine functions, or both, depending on the programmed fuse configuration. A 20 ns propagation delay provides useful timing margin in control, decoder, and asynchronous interface circuits, while the 5 V operating point remains compatible with conventional 5 V logic systems. Typical uses include industrial control logic, telecommunications status decoding, peripheral-interface control, test-equipment sequencing, and compact glue-logic implementations. The 28-pin PLCC footprint is especially relevant to designs that need a socketed or legacy-compatible logic package rather than a high-density FPGA. Designers should confirm device programming, pin definitions, and timing against the manufacturer datasheet before treating the part as a modern drop-in replacement for another SPLD family. The most important layout consideration is access to the programming interface and the PLCC footprint. Preserve clearances around the package, follow the manufacturer pin-definition table, and provide stable supply decoupling close to the power and ground pins. Because device speed and temperature grades are encoded in the suffix, verify the complete ordering code rather than substituting only the base ATF22V10B designation. This page consolidates the manufacturer family specifications, exact-package information, programming and lifecycle considerations, verified drop-in references, and practical design guidance into a single engineering view for the ATF22V10BQL-20JC.
ATF22V10BQL-20PC 20ns 10-Macrocell EE PLD | Microchip
The Microchip Technology ATF22V10BQL-20PC is a 20 ns, 10-macrocell electrically erasable CMOS programmable logic device in a 24-pin PDIP package. It belongs to the ATF22V10B family, which uses electrically erasable Flash memory to retain programmed logic configurations. The device operates from a nominal 5 V supply, while the ATF22V10B family supports speed grades down to 7.5 ns and power dissipation as low as 10 mA. Its through-hole 24-pin PDIP format supports prototyping, legacy industrial equipment, control panels, and repair applications. An electrically erasable programmable logic device, or EE PLD, is a semiconductor that stores configurable Boolean logic in nonvolatile memory. It occupies the logic-IC branch of the broader integrated-circuit hierarchy and provides a compact alternative to a collection of individual gates. Unlike mask-programmed devices, an EE PLD can be reprogrammed during development, production setup, or field maintenance without replacing the integrated circuit. The ATF22V10B family provides 10 macrocells, a 20 ns speed grade for this ordering code, and 5 V CMOS operation. Its electrically erasable Flash technology supports nonvolatile configuration retention, while the 10 mA low-power family option addresses designs in which supply current is important. The 24-pin PDIP package uses a 0.300-inch, 7.62 mm pitch according to the product listing data. Technically, the ATF22V10B is structured for compact combinational and registered logic implementation. Each macrocell supports the programmable logic resource required by the 22V10 architecture, allowing common control, decoding, state-machine, and glue-logic functions to be consolidated into one package. Because the target is a legacy EE PLD, engineers should confirm the programmed JEDEC fuse map, timing limits, and pin behavior against the manufacturer datasheet before modifying an existing design. Typical uses include industrial controller address decoding, legacy interface adaptation, sequencing logic, programmable pulse generation, and small embedded control systems. The 24-pin PDIP package is particularly useful where plug-in IC sockets, through-hole assembly, or field replacement are preferable to a fine-pitch surface-mount footprint. The primary design constraint is supply compatibility. The ATF22V10B family specifies 5 V operation, with tolerance ranges that depend on the device grade. Existing boards should also be checked for timing, macrocell allocation, and programming-file compatibility before substituting another PLD. A modern microcontroller or CPLD may offer more resources, but it can require a different package, firmware workflow, and board-level pin assignment. This product record combines the verified device identity, package, speed, macrocell, memory-technology, and family operating characteristics with practical selection guidance, qualification boundaries, and drop-in alternatives. Engineers can compare package-compatible options while using the manufacturer datasheet and programmed-device documentation as the final authority for design implementation.
ATF22V10BQL-20SC - 20ns EE PLD | Microchip Technology
The Microchip Technology ATF22V10BQL-20SC is a 20 ns electrically erasable CMOS programmable logic device with 10 macrocells, housed in a 24-pin SOIC package. The device uses electrically erasable Flash memory, operates from a nominal 5 V supply, and belongs to the ATF22V10B family of high-performance simple PLDs for compact control, interface, and decoding logic. A simple programmable logic device, or SPLD, is a semiconductor whose digital logic function is defined by a user-programmed fuse map. The ATF22V10B family combines CMOS implementation with electrically erasable Flash memory, making it a member of the broader programmable-logic hierarchy: SPLD, programmable logic device, logic IC, and semiconductor. Unlike mask-programmed devices, electrically erasable PLDs can be reprogrammed during development, simplifying logic changes without requesting new fixed-mask production parts. The ATF22V10B family provides speed options down to 7.5 ns and low-power options with power dissipation as low as 10 mA. The QL designation in ATF22V10BQL identifies the low-power family variant, while the -20SC ordering code identifies a 20 ns speed grade in a commercial-temperature 24-pin SOIC package. Its 10 macrocells provide a practical balance between logic capacity, predictable propagation delay, and board area for embedded control designs. Technically, the device implements combinational or registered logic from a programmed architecture. Electrically erasable Flash memory retains the configuration when power is removed and allows the programmed logic to be changed with compatible programming equipment. Timing specifications apply across the family's stated 5 V nominal supply ranges: 5 V plus or minus 10 percent for military and industrial grades, and 5 V plus or minus 5 percent for the commercial grade. Designers should select system tolerances that remain inside the appropriate operating range. Typical applications include legacy-compatible address decoding, glue logic, bus-interface qualification, control-signal generation, and small finite-state-machine implementations. The device can also support replacement or modernization of older GAL22V10-style logic when its architecture, fuse map, timing, supply requirements, and package pins have been verified against the system design. It is particularly useful where a compact SPLD is preferable to a larger FPGA or microcontroller. For a sound PCB implementation, keep the supply and ground connections short, route programming and control signals away from sensitive analog paths, and follow the manufacturer's pin-description table when assigning every signal. Verify the programmed output states, reset behavior, timing margins, and unused-pin treatment in the final design. Confirm that the system supply tolerance and operating environment satisfy the commercial-grade requirements before releasing production hardware. This product summary combines the manufacturer's ATF22V10B family information with the exact ATF22V10BQL-20SC package and ordering details, then adds practical programming, compatibility, and design considerations. It is intended to help engineers identify the correct legacy-logic device, compare speed-grade options, and plan a controlled drop-in replacement without overlooking supply, temperature, timing, or footprint constraints.
ATF22V10C-10JC - 10ns 5V EEPROM PLD | Microchip
The Microchip Technology ATF22V10C-10JC is a 10 ns, 5 V electrically erasable programmable logic device with 10 macrocells and 500 gates, housed in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It combines a 22V10-compatible logic architecture with electrically erasable Flash memory for nonvolatile configuration, allowing the implemented Boolean function to be reprogrammed without replacing the device. A programmable logic device is a semiconductor that stores a configured logic function in nonvolatile memory. The ATF22V10C belongs to the PLD family within the broader logic IC and semiconductor hierarchy. Its product-sum-of-products architecture is intended for compact control, decoding, and glue-logic implementations where a small gate count and user-programmable function provide an efficient alternative to a general-purpose microcontroller. The -10JC grade is specified for 10 ns operation from a nominal 5 V supply. The ATF22V10C family offers speed options down to 5 ns and power dissipation as low as 10 µA typical. An integrated latch feature holds inputs at their previous logic states, while electrically erasable Flash technology supports repeated configuration changes during development and system updates. Atmel developed the ATF22V10C using high-performance CMOS electrically erasable Flash technology. Microchip support material identifies the ATF22V10C family as pin-to-pin and JEDEC fusemap compatible with the GAL22V10, providing a practical migration path for designs using that legacy PLD architecture. Exact AC and DC limits must be checked against the manufacturer datasheet for the selected operating range. Typical uses include address decoding, control-signal generation, state-machine sequencing, interface adaptation, and general-purpose fixed logic in industrial control, communications, instrumentation, and embedded systems. Its 10 macrocells provide enough logic density for compact Boolean functions, while the 28-pin PLCC package supports conventional through-hole board construction. For a new design, confirm the required fuse map, supply tolerance, temperature grade, and timing budget before assigning the device. Programming tooling must support the ATF22V10C architecture and the required JEDEC-compatible fuse map. Leave programming-test access and power-discharge paths compatible with the manufacturer reference configuration. This page combines package and performance details, replacement guidance, application-specific engineering guidance, and a parameter comparison to support design selection and legacy-board maintenance. It also distinguishes exact drop-in options from devices that require different packages or timing.
ATF22V10C-10JI - 10-Macrocell 10ns Flash PLD | Microchip
The Microchip Technology ATF22V10C-10JI is a 10-macrocell, electrically erasable CMOS programmable logic device (PLD) with a 10 ns propagation delay, packaged in a 28-pin PLCC J-lead package. It is designed for legacy and industrial logic-control applications requiring programmable AND/OR logic, registered outputs, and flexible in-system configuration using electrically erasable Flash memory. A programmable logic device is a semiconductor that implements a Boolean function through user-programmed logic rather than a fixed gate arrangement. The ATF22V10C series provides 10 macrocells, a 22V10-compatible architecture, and a JEDEC-compatible fuse map for applications previously implemented with GAL22V10-type devices. Electrically erasable Flash technology allows the configuration to be reprogrammed, supporting design revisions, production programming, and field-updatable control logic. The ATF22V10C-10JI is identified by its 10 ns speed grade and industrial temperature qualification. The manufacturer describes the ATF22V10C family as supporting speeds down to 5 ns, with typical power dissipation as low as 10 microamps. The device operates from a nominal 5 V supply, with the supplied manufacturer material specifying the full 5 V plus or minus 10 percent range for military and industrial temperature ranges and 5 V plus or minus 5 percent for commercial operation. Typical applications include industrial control interfaces, legacy peripheral emulation, address decoding, bus arbitration, interface translation, and small state-machine implementations. Its 10 macrocells make it suitable for compact glue-logic designs where a discrete gate network would be larger or less flexible. The electrically erasable Flash configuration also makes the device useful where engineering changes are expected during prototype development or maintenance cycles. When designing around this PLD, verify the 28-pin PLCC pinout and the exact fuse-map and programming-software compatibility before updating an existing GAL22V10 design. The ATF22V10C-10JI is not a general-purpose microcontroller: it implements deterministic combinational and registered logic without firmware execution. Confirm supply tolerances, timing requirements, temperature range, programming toolchain, and output-drive requirements against the manufacturer datasheet. This page consolidates the manufacturer specifications, package information, cross-reference information, and practical selection considerations for engineers evaluating a pin-compatible replacement or designing new compact control logic.
ATF22V10C-10PC - 10ns Flash EEPLD, 500 Gates | Microchip
The Microchip Technology ATF22V10C-10PC is a 10 ns, 500-gate electrically erasable programmable logic device with 10 macrocells, 5 V supply operation, and a 24-pin PDIP package. The device combines a reusable CMOS PLD architecture with electrically erasable Flash memory, allowing its logic configuration to be programmed and rewritten rather than permanently fused. An electrically erasable programmable logic device, or EEPLD, is a programmable-logic semiconductor that stores a sum-of-products Boolean configuration in nonvolatile memory. EEPLDs occupy the position between simple fixed-function gate arrays and larger FPGAs. The ATF22V10C family provides a practical way to implement decoding, address mapping, control logic, glue logic, and other modest-complexity digital functions without using a microcontroller or a large configurable logic array. The ATF22V10C-10PC provides a 10 ns access time, 10 macrocells, and an equivalent gate capacity of 500 gates. It operates from a nominal 5 V supply, with the commercial-temperature version rated for a maximum supply voltage of 5.25 V and an operating range from 0°C to 70°C. Flash-based configuration retention supports design revisions without package removal, while typical power dissipation can be as low as 10 µA across the broader ATF22V10C family. The ATF22V10C uses a PAL-style architecture organized around ten macrocells. Product terms, sum-of-products logic, and a registered output path are combined to implement compact combinational or sequential control functions. Device speeds extend down to 5 ns in the family, but the ATF22V10C-10PC is specifically selected for 10 ns operation. A 5 V supply also keeps interface design compatible with conventional 5 V CMOS logic used in older control and instrumentation equipment. Typical applications include industrial control-panel decoding, legacy peripheral-interface adapters, address and interrupt routing, glue-logic consolidation, and small state-machine implementations. Its PDIP package is particularly useful where a through-hole board requires a leaded component and where a modern FPGA package would be unnecessarily small or difficult to inspect and rework. Designers should confirm the JEDEC fuse map, pin assignments, AC timing, and supply tolerances before replacing an older GAL22V10-family device. A DIP socket can simplify prototype changes, but exposed through-hole leads require adequate clearance from adjacent components. Configuration files and programming documentation should also be archived because the same logical design may depend on the device family's supported fuse map and test infrastructure. This product page combines the ATF22V10C technical characteristics with package-specific alternatives, sourcing guidance, and practical considerations for evaluating a 10 ns Flash EEPLD in new or legacy 24-pin PDIP designs.
ATF22V10C-10PI - 10ns 500-Gate EE PLD | Microchip Technology
The Microchip Technology ATF22V10C-10PI is a 500-gate electrically erasable programmable logic device with 10 macrocells, a 10 ns propagation delay, and a 24-pin PDIP package. It operates from a nominal 5 V supply and combines reusable CMOS PLD architecture with electrically erasable Flash memory programming. A simple programmable logic device is a programmable-logic IC used to implement fixed Boolean functions through user-selected connections and equations. In the broader semiconductor hierarchy, an SPLD belongs to the programmable-logic-device family, which sits below CPLD and FPGA technology. ATF22V10C devices are intended for compact control logic where a small macrocell count and straightforward programming workflow are sufficient. The ATF22V10C family offers speed grades down to 5 ns and typical power dissipation as low as 10 µA. The ATF22V10C-10PI is the 10 ns industrial-temperature version in a 24-pin PDIP package. Each of its 10 macrocells can support combinational or registered logic, while the device architecture provides product terms for implementing common control, decoding, and state-machine functions. An optional pin-controlled power-down function is available in the ATF22V10C family. On DIP and SOIC packages, the PD control is assigned to pin 4. This feature can reduce current consumption when a system does not require the programmed logic to remain active, although the exact power-saving behavior should be confirmed against the manufacturer datasheet for the selected operating mode. Typical uses include industrial interface logic, legacy bus decoding, control-panel signal processing, peripheral data conditioning, and compact embedded-control functions. The 24-pin PDIP format is particularly useful for prototypes, maintenance systems, educational platforms, and designs that retain through-hole construction rather than adopting a surface-mount package. When designing around this device, program it with compatible logic-development software and verify the configured equations, pin assignments, and power-down behavior before releasing a PCB. Do not assume electrical or timing equivalence with a generic GAL22V10 without checking the fuse map, voltage tolerance, speed grade, AC timing, and power behavior in the manufacturer datasheet. This product page combines the device’s electrical characteristics, package details, application guidance, drop-in candidates, and engineering cautions. It also distinguishes verified same-package alternatives from functionally related parts, helping designers make a replacement decision without assuming that identical logic functionality guarantees identical timing, programming, or power characteristics.
ATF22V10C-10PU - 10-Macrocell 5V E2 PLD | Microchip
The Microchip Technology ATF22V10C-10PU is a 10-macrocell, electrically erasable programmable logic device operating from a nominal 5 V supply, with a 10 ns speed grade and a 24-pin through-hole PDIP package. It provides 500 programmable gates according to the Mouser product listing and combines CMOS logic with electrically erasable Flash-memory configuration technology. The device is intended for compact control, decoding, address mapping, glue logic, and legacy GAL22V10-compatible designs. A simple programmable logic device is a semiconductor that stores a Boolean function as a configuration rather than implementing that function through fixed gates. The ATF22V10C belongs to the SPLD and PLD hierarchy, where product terms fuse map, macrocell, and erasable Flash configuration describe how each of its 10 logic macrocells implements registered or combinational logic. This makes the device useful as bridge logic between larger processors, FPGAs, memory devices, and industrial or communications systems. Verified product information identifies 10 macrocells, 500 gates, a 5 V supply, a 10 ns speed designation, and a 24-pin PDIP package. The manufacturer datasheet states that the ATF22V10C family reaches speeds down to 5 ns and low typical power dissipation, while the exact ATF22V10C-10PU operating-temperature limits, current consumption, I/O counts, and AC timing values are not supplied in the verified excerpts. Those values must therefore be confirmed in the manufacturer datasheet before a new design is released. The device architecture is appropriate for deterministic control paths, fuse-map decoding, bus-interface qualification, and small state machines. Microchip support identifies the ATF22V10C family as pin-to-pin and JEDEC-fusemap-compatible replacements for GAL22V10 devices when AC and DC behavior is compatible. Because this -10PU variant is a 10 ns speed grade, systems must preserve setup and timing margins rather than treating the number as a universal operating frequency. Typical uses include industrial control, legacy peripheral emulation, address decoding, signal conditioning, test adapters, and compact control logic where 500 gates of programmable integration are sufficient. Mechanically, the PDIP format supports conventional through-hole assembly, prototyping, repair, and legacy boards. Surface-mounted systems should not assume that another ATF22V10C package is interchangeable because package drawings, pin availability, and assembly requirements differ. The main design consideration is configuration compatibility. Confirm the JEDEC fuse map, pin assignments, supply voltage, timing grade, output-drive assumptions, and unused-pin treatment against the exact manufacturer datasheet. A nominal 5 V part should not be assumed suitable for 3.3 V systems without an explicit rail-level specification. For production, validate programming algorithms, erase-and-program behavior, and system timing under worst-case supply and temperature conditions. This page combines verified manufacturer and distributor facts with explicit data gaps, package-aware replacement guidance, comparison parameters, and practical legacy-logic design notes. It is intended to accelerate component identification while preventing unverified electrical or lifecycle assumptions from entering a production BOM.
ATF22V10C-10SC - 10ns Flash EEPROM PLD 24-SOIC | Microchip
The Microchip Technology ATF22V10C-10SC is a high-performance CMOS electrically erasable programmable logic device with 10 macrocells, 10 ns propagation speed, and a 24-SOIC package. It uses nonvolatile electrically erasable Flash memory to retain programmed logic after power removal, making it a practical alternative to fuse-based and antifuse GAL22V10 devices when field programmability or reusable configuration is important. The device operates from a 5 V supply and is part of the ATF22V10C 22V10 programmable-logic family. A programmable logic device, or PLD, is a semiconductor whose internal digital logic connections can be configured after manufacture. The PLD category includes simple programmable arrays, complex programmable logic devices, and field-programmable gate arrays. ATF22V10C-10SC occupies the small-to-medium logic position: 10 macrocells are sufficient for decoding, control sequencing, state-machine logic, and compact combinational or registered functions while avoiding the resource requirements of a larger FPGA. Key features include 10 macrocells, a 10 ns device speed, CMOS construction, electrically erasable Flash configuration memory, and a 24-pin SOIC package. The 10 ns speed rating supports timing designs requiring faster propagation than many older fuse-based GAL22V10 implementations. Because configuration is electrically erasable, the same device can be reprogrammed during development, qualification, or field update rather than being permanently fused. The ATF22V10C architecture supports mixed logic through programmable macrocells rather than a fixed gate array. Configuration data is stored in nonvolatile Flash memory, so the implemented control function remains available after power cycling. The manufacturer identifies speeds down to 5 ns for the broader ATF22V10C family, while the -10SC suffix selects the 10 ns grade. An optional pin-controlled power-down function is also documented for the family, allowing a design to place the PLD into a lower-power state when appropriate. Typical uses include industrial controller interface logic, address decoding, sequencing controllers, legacy GAL22V10 replacements, test-fixture control, and embedded systems that need a compact erasable logic block. The ATF22V10C can be especially useful where a GAL22V10C, GAL22V10D, or compatible JEDEC fuse map is specified, although designers should verify pin and fuse-map compatibility for each selected package and grade. For a reliable PCB implementation, preserve the manufacturer's recommended decoupling and programming interface, use the exact pinout for the 24-SOIC package, and confirm the compiled fuse map against the target logic before deployment. Treat the device as a PLD rather than a general-purpose processor: it implements fixed digital equations but does not execute firmware. Stable power, defined control inputs, and careful programming-mode handling are therefore central to predictable operation. This product data combines the manufacturer’s device description, package information, programming guidance, and verified cross-reference findings with practical implementation notes. It highlights the ATF22V10C-10SC’s most important selection criteria—10 macrocells, 10 ns speed, 5 V operation, 24-SOIC packaging, and electrically erasable Flash configuration—while identifying where a package-qualified replacement must be confirmed before PCB use.
ATF22V10C-10SI - 10ns 500-Gate EEPLD | Microchip
The Microchip ATF22V10C-10SI is a 500-gate electrically erasable programmable logic device with 10 macrocells, a 10 ns propagation delay, and a 24-SOIC package. It combines CMOS logic with electrically erasable Flash memory, allowing the fuse map to be reprogrammed without a dedicated programmer. The device operates from a nominal 5 V supply and supports industrial-temperature operation. An EEPLD is a programmable logic device whose configuration memory can be electrically erased and rewritten. Within the broader semiconductor hierarchy, an EEPLD is a programmable logic IC, a member of the PLD family, and a practical alternative to a small collection of discrete gates. ATF22V10C devices are commonly used to implement decode logic, state machines, interface control, and fixed Boolean functions in compact industrial and communications equipment. Key features include 10 ns propagation delay, 10 macrocells, and 500-gate logic capacity. The manufacturer datasheet doc0735 states that ATF22V10C speeds extend down to 5 ns and power dissipation can be as low as 10 uA typical. An optional pin-controlled power-down function provides a way to reduce consumption when the device is not required, while the latch feature holds input states for testing and board-level diagnostics. The ATF22V10C architecture implements combinational or registered logic through a configurable fuse map. Because the memory is electrically erasable, the design can be reprogrammed during manufacturing, prototype development, or field updates when the application permits device access. The 24-SOIC package is a surface-mount option for designs that require a small, widely supported package rather than a leaded DIP or pin-grid package. Typical uses include industrial control interfaces, telecommunications line-card logic, automotive control modules, embedded peripheral decoding, and legacy system refresh projects. The 10 ns device class is appropriate for control logic and interface functions where propagation delay must remain predictable without introducing unnecessary cost or power dissipation for higher-speed performance. When planning a PCB, treat all 24 SOIC positions as package pins even if the design leaves some configurable inputs or outputs unused. Program the device according to the manufacturer's programming guidance and verify the power-down, clock, and registered-output behavior in the chosen fuse map. Do not substitute the electrical characteristics of a faster speed grade without rechecking timing margins. This page brings together the manufacturer's device description, package and timing information, a structured drop-in comparison, programming and pinout guidance, and practical application notes. It is designed to help engineers confirm footprint compatibility, evaluate speed-grade trade-offs, and plan an industrial-temperature PLD implementation efficiently.
ATF22V10C-10XC 10ns 24-TSSOP Flash PLD | Microchip
The Microchip Technology ATF22V10C-10XC is a 500-gate high-performance CMOS electrically erasable programmable logic device (PLD) with 10 macrocells, a 10 ns device speed, and a 24-TSSOP package. It uses electrically erasable Flash memory for in-circuit reprogramming and is positioned as a modern programmable alternative to fuse-map PLDs. The device is intended for designs requiring compact logic implementation, field programmability, and logic replacement without changing the board footprint. A programmable logic device is a semiconductor that stores configurable Boolean logic functions in an on-chip memory structure. The ATF22V10C belongs to the PLD hierarchy, combining the simplicity of a fixed logic array with the flexibility of a user-programmed device. Its electrically erasable Flash memory permits the configuration to be programmed and reprogrammed, making the device suitable for legacy GAL22V10 designs, control logic, interface decoding, and small standalone state machines. The ATF22V10C family supports speeds down to 5 ns, while the ATF22V10C-10XC suffix identifies the 10 ns version. The family also offers power dissipation as low as 10 uA typical according to the manufacturer datasheet. The commercial-grade ATF22V10C-10XC is supplied in a 24-pin TSSOP package, enabling compact PCB layouts and automated surface-mount assembly. The same family uses 5 V ± 5% for commercial operation and supports additional temperature and qualification grades in other variants. The device provides 10 macrocells, 22 dedicated inputs, and ten dedicated outputs in the 22V10 architecture. These resources suit gate-count-intensive combinational logic, registered control functions, address decoding, and glue logic where a small CPLD or FPGA would be excessive. Because the device is Flash-programmable, production programming can be automated, and field updates can be performed without replacing the component. Programming systems support the JEDEC programming-file workflow described by Microchip application documentation. Typical ATF22V10C-10XC applications include legacy GAL22V10 replacement, industrial control and instrumentation, digital test equipment, printer and peripheral control, simple keypad or display decoding, and compact embedded-control subsystems. The principal design consideration is compatibility: although ATF22V10C variants are known to replace GAL22V10 devices, engineers should verify AC timing, DC operating limits, pin assignment, and JEDEC fuse-map compatibility against the exact device being replaced. For a drop-in migration, compare the complete package drawing and pin description table in the manufacturer datasheet before modifying the PCB. Preserve the specified decoupling and programming connections, and validate every path against the target system timing. This page combines the manufacturer specifications, package details, programming guidance, replacement considerations, and practical design notes needed to evaluate the ATF22V10C-10XC for an existing 22V10 design. This product information also distinguishes documented device capabilities from assumptions about lifecycle, pricing, and exact cross-brand replacements. Engineers can use the package, macrocell, speed, voltage, and programming details to assess suitability, then request current commercial availability and lead time through the Request a Quote form on this page.
ATF22V10C-15PC 15ns 500-Gate EEPLD | Microchip Technology
The Microchip Technology ATF22V10C-15PC is a high-performance electrically erasable CMOS programmable logic device with 10 macrocells, a 15 ns propagation delay, and a 24-pin PDIP package. It is designed for 5 V digital logic implementations requiring reprogrammable combinational or registered functions, including approximately 500 gate equivalents. The device uses electrically erasable Flash memory, allowing its logic configuration to be changed without conventional fuse programming. A programmable logic device is a configurable semiconductor that implements digital functions through a programmed logic network. In the broader hierarchy, the ATF22V10C is an EEPLD, a simple PLD, and ultimately a programmable semiconductor. Compared with a fixed gate array, an EEPLD provides a practical way to consolidate several gates, registers, and product-sum terms into one device while retaining field reprogrammability. Key features include a 15 ns speed grade, 10 macrocells, a latch feature that holds inputs at their previous logic states, and operation from a nominal 5 V supply. The manufacturer documentation describes ATF22V10C family speeds down to 5 ns, while the -15 suffix identifies the 15 ns ATF22V10C variant. The 24-pin PDIP package supports conventional through-hole assembly and is useful where a socketed or manually assembled design is preferred. The electrically erasable Flash architecture combines a reusable configuration memory with a configurable logic array. Each macrocell can contribute product-term logic, registered output behavior, and programmable feedback according to the device architecture. The latch function is useful in designs that must preserve input or logic state during clock-related control operations. Because the device is pin-compatible with JEDEC GAL22V10 fusemaps, existing GAL22V10 designs can use the ATF22V10C family after a complete electrical, timing, and programming-tool review. Typical uses include industrial control logic, interface decoding, state sequencing, counter and latch functions, telecommunications control, and compact glue-logic implementations. The 5 V supply and 15 ns propagation delay make the part appropriate for legacy control systems, retrofit products, and equipment requiring a 24-pin through-hole PLD footprint. The primary design consideration is preserving the original GAL22V10-compatible pinout, fuse map, output polarity, clock behavior, and timing assumptions. Confirm programming software support, supply tolerances, temperature limits, and all AC and DC differences before substituting it into an existing production design. A socketed DIP implementation also requires attention to electrostatic handling and programming after installation. This product summary combines the manufacturer family specifications, package details, programming characteristics, and GAL22V10 replacement guidance with practical guidance for PCB layout, timing review, and drop-in replacement assessment.
ATF22V10C-15PI - 15 ns 10-Macrocell EEPLD | Microchip
The Microchip Technology ATF22V10C-15PI is a high-performance CMOS electrically erasable programmable logic device with 10 macrocells, a 15 ns propagation delay, and 24 I/O pins in a 24-pin PDIP package. It belongs to the 22V10 architecture and stores its configuration in electrically erasable Flash memory, allowing the programmed logic design to be changed without a dedicated UV-erasure cycle. An electrically erasable programmable logic device, or EEPLD, is a semiconductor that implements fixed digital logic through a user-programmed configuration. In the product hierarchy, an EEPLD is a programmable logic device, a digital integrated circuit, and a semiconductor. The ATF22V10C architecture combines macrocell-based logic implementation with nonvolatile Flash configuration memory, making it useful where a board requires flexible control logic, decoding, address translation, state-machine implementation, or replacement of several conventional gate arrays. The ATF22V10C-15PI provides a 15 ns speed grade and 10 macrocells. The manufacturer describes the broader ATF22V10C family as supporting speeds down to 5 ns and typical standby power dissipation as low as 10 microamperes. Its architecture uses proven electrically erasable Flash memory technology, while the 22V10 design is compatible with the established GAL22V10 fusemap and pin arrangement according to Microchip's replacement guidance. The ATF22V10C family is specified for a nominal 5 V supply, with industrial-temperature speed grades specified over 5 V ±5% and military-temperature speed grades over 5 V ±10%. The -15PI designation identifies a 15 ns industrial-temperature grade supplied in a PDIP package. This combination is intended for legacy and industrial control systems where through-hole construction, nonvolatile configuration, and deterministic logic timing are important. Typical uses include industrial automation, telecommunications infrastructure, embedded control, peripheral decoding, and compact state-machine logic. In these systems, the device can consolidate Boolean equations and registered functions that would otherwise require multiple standard logic packages. The 24-pin PDIP format also supports repairable and manually assembled industrial equipment where through-hole sockets or leaded packages remain practical. For PCB design, place the 24-pin PDIP according to the manufacturer's pin-description table and preserve the standard GAL22V10-compatible footprint and programming interface. Confirm the required supply voltage, operating temperature, output timing, and unused-pin states in the datasheet before production release. For a new design, also evaluate a smaller surface-mount PLD or an FPGA when board area, modern tooling, or higher logic density is more important than the 22V10's established leaded-package footprint. This product page combines the manufacturer's ATF22V10C architecture information with package, timing, macrocell, and cross-reference details, then adds practical selection guidance for engineers maintaining GAL22V10-based and ATF22V10C-based equipment.
ATF22V10C-15SC - 15ns 500-Gate EEPROM PLD | Microchip
The Microchip ATF22V10C-15SC is a high-performance CMOS electrically erasable programmable logic device (EEPLD) with 10 macrocells, approximately 500 gates of logic, a 15 ns device speed, and a 24-SOIC package. It uses electrically erasable Flash memory technology and operates from a nominal 5 V supply, making it suitable for compact control, interface, and fixed-logic designs that require nonvolatile configuration. A programmable logic device is a semiconductor in which the user implements digital functions by programming an internal logic array. The ATF22V10C family belongs to the SPLD hierarchy, combining a regular macrocell structure with nonvolatile Flash programming. Compared with a mask-programmed ASIC, it supports design changes without fabricating a new photomask; compared with a microcontroller, it provides deterministic combinational and registered logic without executing firmware. Key characteristics include 10 macrocells, a nominal 15 ns speed grade, 5 V operation, and low standby power dissipation down to 10 uA typical. The device family is specified over 5 V ± 10% for military and industrial temperature ranges and over 5 V ± 5% for other indicated operating grades. Its nonvolatile Flash configuration retains the implemented logic when power is removed, while the latch feature can hold inputs at their previous logic states. Typical uses include interface translation, control logic, address decoding, state-machine sequencing, industrial automation, and legacy equipment upgrades. The 24-SOIC outline also makes the ATF22V10C-15SC practical for conventional through-hole assembly rather than requiring a fine-pitch surface-mount redesign. Designers should verify timing against the selected system clock, provide the required programming and power-sequencing controls, and confirm that the JEDEC fuse map matches the intended design. The Microchip ATF22V10C family is specified for speeds down to 5 ns across the broader family, but the -15 suffix identifies the 15 ns grade of this particular device. This product page combines the manufacturer electrical characteristics with practical guidance for programming, pin assignment, timing analysis, and system integration. It also distinguishes documented replacement paths from package-compatible alternatives so engineers can assess PCB impact before committing to a substitution.
ATF22V10C-5JC - 500-Gate EE PLD, 10 Macrocells, 5ns | Microchip
The Microchip ATF22V10C-5JC is a high-performance CMOS electrically erasable programmable logic device (EE PLD) providing 500 logic gates in 10 macrocells, with 5 ns propagation delay, packaged in a 28-pin J-lead PLCC (QCCJ, 11.51 mm x 11.51 mm) surface-mount package. It operates from a single 5 V supply with commercial-grade 5 V +/- 5% tolerance and consumes as little as 10 uA in power-down state. The device replaces the legacy fuse-programmed GAL22V10 architecture with in-circuit electrically erasable flash memory, so a design can be re-programmed without a programmer socketed into a dedicated fixture. An EE PLD is a programmable logic device whose configuration memory is non-volatile and re-writable. Within the wider semiconductor hierarchy, ATF22V10C sits in the programmable logic family, which sits inside the broader logic IC and programmable logic device categories. A GAL22V10-style device maps a fixed sum-of-products architecture onto 10 macrocells, each with 8 product terms feeding an OR plane plus a configurable flip-flop. That structure makes the ATF22V10C a natural fit for glue logic, control decoding, address decoding and bus arbitration logic that must be re-worked late in a design cycle. Key electrical features include a 5 ns minimum tPD, 10 macrocells of 500 total gates, a 28-pin PLCC footprint, an input latch feature that holds inputs at their previous logic states, and flash-based in-circuit re-programming. Unlike mask-programmed or OTP alternatives, the ATF22V10C can be updated on the assembly line, which shortens NPI schedules and eliminates disposal of obsolete programmed parts. Technically, the ATF22V10C is architecturally compatible with the classic GAL22V10 JEDEC fuse map, so existing GAL22V10 pinouts, fusing tables and JEDEC third-party programmer support carry over directly. Microchip publishes the ATF22V10C as the recommended replacement for the GAL22V10, noting that AC and DC characteristics are very similar with only minor differences. Typical applications include address decoding for memory and peripheral buses, control-plane state machines for industrial and instrumentation equipment, retrofit glue logic around legacy microcontrollers, ASIC prototyping, and interface logic in test and measurement equipment. The 28-pin PLCC package gives short, low-inductance leads that support both hand soldering and reflow at 5 V clock speeds. When designing around the ATF22V10C, remember that its 10-macrocell architecture maps to classic GAL22V10 JEDEC equations; use a JEDEC-compatible programmer and verify the fuse map against the vendor library before taping out. Place a 0.1 uF decoupling capacitor at each supply pin and keep PLCC leads short to limit ground bounce on fast output transitions. This page consolidates verified distributor specifications for the ATF22V10C-5JC, pin-compatible drop-in alternatives, JEDEC fusemap compatibility notes, and practical design guidance that is not consolidated in a single manufacturer document.
ATF22V10C-5JX - 5ns 500-Gate EE PLD | Microchip Technology
The Microchip Technology ATF22V10C-5JX is a 5 ns, 500-gate electrically erasable programmable logic device with 10 macrocells, supplied in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It operates from a 5 V supply and combines a 166 MHz maximum device frequency with electrically erasable Flash-memory configuration. The ATF22V10C series provides a practical way to implement compact glue logic, address decoding, control sequencing, and interface adaptation where a small microcontroller or FPGA would be unnecessary. A programmable logic device, or PLD, is a semiconductor whose digital function is defined by stored programming data rather than fixed logic. The ATF22V10C belongs to the simple PLD hierarchy: PLD > simple PLD > SPLD > electrically erasable PLD. Compared with a mask-programmed PAL device, its Flash-memory configuration can be changed during development, simplifying logic revisions, prototype corrections, and production programming workflows. Key features include 10 macrocells, approximately 500 gates, a 5 ns speed grade, a 166 MHz stated maximum frequency, and 5 V operation. The electrically erasable Flash architecture retains the programmed function without continuous electrical rewriting. According to the manufacturer datasheet, power dissipation can be as low as 10 uA typical, making the device useful where low standby consumption is valuable. A pin-controlled power-down feature is also available, with the PD function located on pin 5 for PLCC packages. The ATF22V10C-5JX is an older, compact CMOS PLD rather than a field-programmable gate array. Its 10 macrocells provide substantially less logic capacity than modern CPLDs and FPGAs, but the 5 ns speed class supports faster decision and decoding paths than slower SPLD grades. The main design trade-off is fixed logic capacity: complex state machines, wide arithmetic functions, and large parallel interfaces may exceed the available macrocells even when the propagation delay is suitable. Typical applications include industrial control address decoding, peripheral-chip-select generation, asynchronous interface adaptation, embedded reset and power sequencing, test-fixture control, and compact legacy-controller support. Because the device is electrically erasable, it is especially useful for bridge or glue logic that must evolve independently of a larger system-on-chip. Its J-lead PLCC package also provides a practical surface-mount option for boards that cannot accommodate a through-hole DIP package. Designers should confirm that the required Boolean equation set fits the 10 macrocells and should verify the JEDEC-compatible fuse map before replacing a GAL22V10 or designing a new board. Programming tooling and the correct ATF22V10C device family must be selected. The 5 V supply, 5 ns timing grade, and PLCC footprint should all be checked against the existing schematic and PCB library before procurement. This product page consolidates manufacturer specifications, distributor pricing, package information, and verified replacement information. It also provides practical selection guidance for ATF22V10C speed grades and clearly distinguishes verified drop-in candidates from options that change speed grade, temperature grade, package, or device architecture.
ATF22V10C-7JC - 500-Gate 7 ns EE PLD | Microchip Technology
The Microchip Technology ATF22V10C-7JC is a 500-gate electrically erasable programmable logic device with 10 macrocells, a 5 V supply, and a 7 ns speed grade, housed in a 28-pin PLCC package. It belongs to the ATF22V10C family of CMOS PLDs and provides a practical combination of combinational logic capacity, flash-based reprogrammability, and surface-mount integration for established control and interface designs. An electrically erasable PLD is a user-programmable logic device whose configuration is stored in nonvolatile memory. In the broader semiconductor hierarchy, the ATF22V10C-7JC is a PLD, then a programmable logic device, then an integrated circuit, and finally a semiconductor. Its ten macrocells make it suitable for compact glue-logic implementations, pin mapping, control decoding, and other functions that can be consolidated into one device rather than implemented with multiple conventional logic ICs. The verified product information identifies the device as a 22V10-series EE PLD with 500 gates, 10 macrocells, a 5 V operating supply, and a 7 ns speed designation. A separate distributor listing describes the propagation delay as 7.5 ns, so the two published figures should be checked against the applicable datasheet revision and test conditions before using the timing figure for a safety-critical design. The family documentation also describes electrically erasable flash memory, low-power operation, and speeds down to 5 ns across the broader ATF22V10C range. The ATF22V10C architecture provides multiple product-term configurations for the ten output macrocells. Microchip documentation states that the family supports programmed operating modes and that related ATF22V10CZ and ATF22V10CQZ devices form a superset of generic 22V10 architectures. The ATF22V10C series also offers an optional pin-controlled power-down function; in the PLCC package, the power-down signal is identified at pin 5 in the manufacturer documentation. Typical uses include industrial control logic, interface decoding, legacy peripheral emulation, counter or state-machine implementation, and compact control logic in otherwise discrete-logic systems. The 28-pin PLCC footprint is especially relevant to maintenance and redesign work involving boards designed around the classic 22V10 architecture. Its nonvolatile, electrically erasable configuration also supports repeatable engineering changes without a dedicated ultraviolet-erase step. When designing around the ATF22V10C-7JC, preserve the manufacturer's pin assignment and programming-device requirements, and do not substitute a PLD solely because its gate count is similar. Verify the JEDEC fuse-map compatibility, supply voltage, macrocell product-term allocation, active levels, timing grade, and temperature designation against both the target and proposed replacement datasheets. The verified data does not supply exact package dimensions beyond the 28-pin PLCC identification, so mechanical drawings should be taken from the official package documentation. This page combines the verified manufacturer and distributor information, genuine cross-reference candidates, application guidance, and pin-compatibility cautions rather than repeating raw catalog data alone. It also separates confirmed device facts from fields that remain unavailable, helping engineers evaluate this legacy PLD and any replacement before committing a board layout or production order.
ATF22V10C-7JI - 10-Macocell 5V EE PLD | Microchip
The Microchip Technology ATF22V10C-7JI is a 10-macocell electrically erasable programmable logic device (EE PLD) with a 7.5 ns propagation delay, 5 V input voltage, and a 28-pin PLCC J-lead package. It belongs to the ATF22V10C family and uses electrically erasable Flash memory, allowing the implemented logic design to be reprogrammed during development or field updates. An EE PLD is a semiconductor whose digital logic function is user-programmed through a configurable internal array. The ATF22V10C-7JI provides 10 macrocells, equivalent to approximately 500 gates according to distributor data. This makes it useful for implementing fixed combinational and registered logic, interfacing legacy systems, consolidating small amounts of glue logic, and providing compact control functions in industrial automation, consumer electronics, and telecommunications equipment. Key characteristics include a 7.5 ns speed grade, operation from a 5 V input supply, surface-mount construction, and an industrial temperature grade. The family also provides an optional pin-controlled power-down function in which the PD control appears on pin 5 of the PLCC package. Electrically erasable Flash technology gives the device a different programming and update model from one-time-programmable fuse-based PAL and GAL devices. The ATF22V10C architecture combines programmable input and output structures with dedicated clock and output-enable functions. The device can implement registered logic through its macrocell flip-flops while retaining the familiar JEDEC-compatible 22V10 logic arrangement. This architecture is intended for designs requiring more flexibility than a fixed gate array but less complexity than a modern FPGA. Typical uses include industrial control logic, communication-interface decoding, address and command multiplexing, legacy peripheral adaptation, and compact system-control functions. Because the device is packaged in a 28-pin PLCC, it is particularly relevant to equipment upgrades that already use that footprint and JEDEC-compatible logic mapping. When replacing an older GAL22V10 implementation, verify the programmed fuse map, pin-controlled power-down behavior, timing grade, temperature range, and supply requirements against the manufacturer datasheet. The PLCC footprint is suitable for surface-mount assembly, but exposed-pad thermal analysis is not applicable because this package does not contain an exposed thermal pad. This product page consolidates verified source data, sourcing information, specification comparisons, and application-oriented design guidance. It also distinguishes documented drop-in alternatives from broader functional replacements and identifies the specific details that must be checked before substituting a legacy programmable-logic device.
ATF22V10C-7JU - 10-Macrocell 7 ns PLD | Microchip | PLCC
Microchip ATF22V10C-7JU is a 500-gate, 10-macrocell electrically erasable programmable logic device with a 7 ns speed grade, 5 V supply, and 28-pin PLCC package. The ATF22V10C family combines CMOS PLD architecture with electrically erasable Flash memory for in-circuit reprogramming. It implements programmable sum-of-products logic in a single package and is suitable for compact control, decoding, interface, and fixed-logic designs. A programmable logic device is a semiconductor whose internal logic connections are configured through programming rather than fixed during fabrication. The ATF22V10C belongs to the SPLD hierarchy, joining PAL-derived combinational logic with erasable nonvolatile configuration memory. Ten macrocells and 500 gates provide more integration than simple fuse-programmed devices while preserving predictable combinational propagation delays. The -7JU ordering identifies the 7 ns speed option, industrial temperature construction, and 28-pin PLCC configuration. The device operates from a nominal 5 V supply, with a documented operating range extending from 4.5 V to 5.5 V. The ATF22V10C family also supports speeds down to 5 ns and standby or power-down dissipation as low as 10 uA typical, allowing designs to balance speed against standby power. The electrically erasable Flash configuration memory distinguishes this device from one-time-programmable fuse-link PLDs. Logic can be revised during development without replacing the package, while the JEDEC-compatible fusemap supports predictable migration from GAL22V10-class designs. The optional pin-controlled power-down function provides another mechanism for reducing current in systems that do not require continuous logic evaluation. Typical uses include industrial control logic, bus decoding, state-machine sequencing, peripheral interfacing, and compact embedded-control subsystems where a small PLD can consolidate multiple gates. The 28-pin PLCC package is suitable for through-hole board assembly and sockets, while the electrically erasable configuration supports engineering revisions and production programming. Designers should compare propagation delay against the system timing budget, confirm absolute maximum and recommended operating voltages, and include pull-up or pull-down resistors where required by the selected configuration. The pin-controlled power-down function uses a dedicated PLCC pin and should be checked against the fuse map before PCB changes. This page combines manufacturer specifications, replacement analysis, application guidance, and drop-in comparison information for faster engineering evaluation.
ATF22V10C-7PC - 7ns 500-Gate Flash PLD | Microchip Technology
Microchip Technology ATF22V10C-7PC is a 7 ns, 500-gate electrically erasable CMOS programmable logic device with 10 macrocells, supplied in a 24-pin PDIP package. It uses electrically erasable Flash memory and operates from a 5 V supply, combining reconfigurable digital logic with a through-hole package suited to legacy control, interface, and industrial automation systems. An EEPLD is a programmable logic device that stores a logic configuration in nonvolatile memory. The device sits within the hierarchy of programmable logic devices, including simple PLDs, complex PLDs, FPGAs, and CPLDs. Unlike a mask-programmed logic array, the ATF22V10C-7PC can be erased and reprogrammed, allowing the same board design to support multiple logic configurations, design revisions, or field updates. The principal performance characteristics are a 7 ns device speed, 500 equivalent gates, 10 macrocells, 5 V operation, and nonvolatile Flash-backed configuration storage. The ATF22V10C family also includes speed options down to 5 ns, and Microchip documents power dissipation as low as 10 μA typical for the family. The commercially graded -7PC ordering code identifies the 7 ns variant in the 24-pin PDIP package. Architecturally, the device implements sum-of-products logic through a fuse-map-compatible PLD arrangement. Microchip identifies the ATF22V10C, ATF22V10CQ, and ATF22V10CQZ as suitable replacements for the GAL22V10 because they are pin-to-pin and JEDEC fuse-map compatible. Electrical and timing characteristics should still be compared against the original GAL22V10 datasheet before substituting them into an existing design. Typical uses include industrial control signal decoding, legacy peripheral interfacing, custom logic functions, product routing, test-fixture control, and small control systems where a compact 10-macrocell PLD is more practical than a larger FPGA. Its nonvolatile Flash configuration also avoids loading the programming pattern into volatile memory after each power-up. Designers should preserve the published 24-pin footprint, supply requirements, timing limits, and output-drive constraints when replacing a GAL22V10 or another compatible PLD. Because the verified source set does not provide a complete pin list, electrical limits, or detailed AC timing tables, those values must be confirmed in the manufacturer datasheet before layout release or production use. This page consolidates verified Microchip and distributor information, identifies same-package replacement candidates, and separates confirmed parameters from data that still requires datasheet review. This added context helps engineers compare ATF22V10C-7PC with legacy PAL/GAL logic without mistaking package similarity for guaranteed system compatibility.