بەرهەمەکان (730+)

TPS22970YZPR - 3.6V 4A 4.7mΩ Load Switch | Texas Instruments
TPS22970YZPR

TPS22970YZPR - 3.6V 4A 4.7mΩ Load Switch | Texas Instruments

The Texas Instruments TPS22970YZPR is a small, space-saving N-channel high-side load switch rated for 3.6 V operation, 4 A pulsed switch current, and 4.7 mΩ typical on-resistance, packaged in an 8-ball DSBGA (WCSP, YZP) chip-scale package. It integrates an N-channel MOSFET biased by a charge pump, an on/off logic input, and an optional output discharge resistor for controlled turn-off behavior. What is a load switch? A load switch is a power-management device that uses an internal MOSFET to connect or disconnect a downstream circuit (a "rail" or "load") from an upstream power source. Unlike a DC-DC converter, a load switch does not regulate voltage — its role is gating, inrush control, sequencing, isolation, and reverse-current blocking. Load switches belong to the broader category of power distribution switches (PDswitches), which sit hierarchically below discrete MOSFETs but above simple pass-gate FETs because they integrate control, protection, and timing into a single IC. Key features of the TPS22970YZPR include a wide input voltage range of 0.65 V to 3.6 V (compatible with 1-cell Li-ion rails as well as 1.0 V/1.2 V/1.8 V/2.5 V/3.3 V logic rails), continuous current up to 2 A and pulsed current up to 4 A, 4.7 mΩ RON that minimizes conduction loss, controlled turn-on to limit inrush current, and an internal discharge path that pulls the output to ground when the switch is disabled. The device operates over -40°C to +105°C and ships on a 0.9 mm pitch WCSP footprint measuring roughly 1.50 mm × 1.50 mm. Architecturally, the integrated charge pump generates a VGS boost above VIN so the NMOS can fully enhance even at very low input voltages — a non-trivial achievement because a standard NMOS would otherwise struggle to pass sub-1 V rails cleanly. This makes the part especially attractive for ultra-low-voltage core rails in mobile and battery-powered designs. Typical applications include power gating in smartphones, wearables, SSDs and solid-state storage modules, portable medical devices, and IoT sensor nodes where the load switch isolates a sleeping sub-system from a battery to extend standby life. The output discharge resistor is particularly useful in multi-rail systems where residual charge on a disabled rail could otherwise leak through the body diode of a downstream load. When designing with this device, pay close attention to the PCB footprint: the WCSP-8 (DSBGA) package requires NSMD pads with precise solder-mask openings and reflow profile matched to JEDEC J-STD-020. Avoid placing vias directly under the balls and follow TI's WCSP layout recommendations. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives from TI's load-switch family, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22990DMLR - 10A, 5.5V, 3.9mOhm Load Switch | TI
TPS22990DMLR

TPS22990DMLR - 10A, 5.5V, 3.9mOhm Load Switch | TI

The Texas Instruments TPS22990DMLR is a single-channel N-channel high-side load switch delivering up to 10 A continuous current with a 3.9 mOhm typical on-resistance, operating over an input voltage range of 0.6 V to 5.5 V in a 10-pin WSON (3x2 mm) package (DML, WSON-10 with exposed pad). A load switch is a power distribution IC that sits between a supply rail and its load, using an internal MOSFET pass element to connect, disconnect, and protect the rail. In the power-management hierarchy, load switches are siblings of hot-swap controllers and eFuses within power distribution ICs, and they are commonly paired with DC-DC converters and LDO regulators to sequence and gate individual rails. Key features of the TPS22990 include the ultra-low 3.9 mOhm on-resistance, which minimizes voltage drop and conduction power loss at high load currents; controlled and adjustable turn-on slew rate via an external CT capacitor, which suppresses inrush current and bus voltage sag; and an integrated power-good (PG) indicator for rail monitoring and sequencing. An optional quick output discharge (QOD) function actively pulls the output low when the switch is off. Architecturally, the device integrates an N-channel MOSFET pass element with gate-drive circuitry powered from a VBIAS supply, allowing the switch to operate down to 0.6 V input while supporting modern low-voltage rails. The adjustable rise time lets designers trade startup time against inrush current for a given output capacitance. Typical applications include server and notebook point-of-load power gating, SSD and storage rail switching, multi-rail power sequencing in SoC and FPGA systems, and battery-powered equipment where low voltage drop is critical. A key design consideration: at 10 A, even 3.9 mOhm dissipates roughly 0.39 W, so PCB copper area under the exposed pad is essential for thermal management. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22990NDMLR - 10A, 5.5V, 3.9mOhm Load Switch | TI
TPS22990NDMLR

TPS22990NDMLR - 10A, 5.5V, 3.9mOhm Load Switch | TI

The Texas Instruments TPS22990NDMLR is a 5.5 V, 10 A, 3.9 mOhm single-channel N-channel high-side load switch housed in a 10-pin WSON (3x2 mm) package, featuring an adjustable controlled turn-on, integrated power-good (PG) indicator, and quick output discharge (QOD) function. A load switch is a power distribution switch, a type of power management IC that sits between a supply rail and its load to gate power on and off, control inrush current, and isolate faults. In the system hierarchy, it belongs to the family of high-side switches used in power trees alongside hot-swap controllers, e-fuses, and DC-DC converters, enabling fine-grained power sequencing and rail management. Key differentiating features include an ultra-low 3.9 mOhm on-resistance, which minimizes both the voltage drop across the switch and conduction power loss at the full 10 A continuous current, and a wide 0.6 V to 5.5 V input voltage range that spans modern sub-1 V core rails up to standard 5 V rails. The adjustable slew rate (soft-start), set via an external capacitor, suppresses inrush current during turn-on, while the integrated PG output simplifies power-rail sequencing and monitoring without external supervisory circuitry. The N-channel MOSFET architecture avoids the body-diode conduction and rds(on) penalties of older P-channel designs at high current. Internal control logic drives the gate with a controlled ramp defined by the CT pin capacitor, and the QOD option actively discharges the output when the switch is disabled, preventing floating rails in multi-rail systems. ESD protection on the pins adds robustness during assembly and handling. Typical applications include SSD and storage power distribution, FPGA and processor core-rail sequencing, networking cards, battery-powered portable systems, and server backplane point-of-load switching, all of which benefit from low-loss high-current switching with controlled turn-on. Design consideration: at 10 A, conduction loss is approximately I2 x R, so PCB copper pour on the IN and OUT pins is essential for thermal management. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22991IBNRAAR - 5.5V 2.7A Load Switch UQFN-HR | Texas Instruments
TPS22991IBNRAAR

TPS22991IBNRAAR - 5.5V 2.7A Load Switch UQFN-HR | Texas Instruments

The Texas Instruments TPS22991IBNRAAR is a 5.5V, 2.7A, 28 mOhm single-channel load switch with controlled slew rate, housed in a 4-pin UQFN-HR (RAA) package measuring just 0.85 mm x 0.75 mm with 0.4 mm pitch. The device integrates an N-channel MOSFET that operates over a 1.0V to 5.5V input voltage range and is characterized for operation from -55C to +125C, covering extreme-temperature and wide-temperature industrial designs. A load switch is a type of power management IC (power distribution switch) that gates a voltage rail on and off under logic control, protecting downstream circuitry from inrush current and enabling power sequencing. Within the power-management hierarchy, the TPS22991I family sits between a voltage regulator and a simple discrete MOSFET switch: it provides controlled turn-on without regulation of the rail voltage itself. Key features include a low on-resistance of 28 mOhm, which minimizes voltage drop and conduction loss at multi-ampere loads, and a controlled slew rate that limits inrush current when charging large bulk capacitance. The ON/OFF control input interfaces directly with low-voltage GPIO signals, allowing the switch to be driven by microcontrollers and processors operating well below the main rail voltage. Low shutdown leakage makes the device suitable for battery-powered designs where off-state quiescent draw must be minimized. Technically, the integrated N-channel pass element is driven by an internal charge-pump-free gate-drive scheme referenced to the input pin, with slew-rate control implemented through a controlled gate-drive ramp. This gives a predictable, monotonic output voltage ramp that avoids the sharp turn-on transients typical of uncontrolled discrete MOSFET switching. Typical applications include power-rail gating for battery-powered portable electronics, module power sequencing in processors and FPGAs, and load switching in industrial sensors operating over extended temperature ranges. The tiny 0.85 mm x 0.75 mm footprint suits densely packed wearables and IoT modules. Design consideration: verify the device pinout carefully. Unlike most single-channel load switches that use an IN-OUT-GND-EN ordering, the TPS22991I pinout is documented as special in TI's E2E forum, so confirm pin assignments against the manufacturer datasheet before layout. This page synthesizes distributor availability, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22992 - 5.5V 6A 8.7mΩ Load Switch | Texas Instruments
TPS22992

TPS22992 - 5.5V 6A 8.7mΩ Load Switch | Texas Instruments

The Texas Instruments TPS22992 is a single-channel load switch with an integrated 8.7 mΩ power MOSFET designed to maximize power density in applications up to 5.5 V input and 6 A continuous output current, housed in an 8-pin WQFN-HR (1.5 mm x 1.25 mm) package. A load switch is a power management IC that sits between a power rail and its load, using an internal MOSFET pass element and control logic to connect or disconnect the load on demand. Load switches occupy the middle of the power management IC hierarchy, below full DC-DC converters and above discrete MOSFET solutions, providing controlled power-up, inrush limiting, rail sequencing, and fault isolation that a bare MOSFET cannot deliver without significant external circuitry. Key features of the TPS22992 include the ultra-low 8.7 mΩ on-resistance, which limits conduction losses to roughly 78 mW at a full 6 A load, an input voltage range up to 5.5 V, and a configurable rise time that gives designers flexibility for power sequencing. The adjustable rise time also minimizes inrush current when switching high-capacitance loads such as large ceramic capacitor banks or downstream SoC core rails. Technically, the TPS22992 uses an N-channel high-side power MOSFET driven by an internal charge-pump gate driver, which allows the switch to achieve extremely low Ron without the voltage-drop penalty of a P-channel device. The TPS22992x family consists of two members: the TPS22992 and the TPS22992S, which differ in their output discharge behavior, letting designers choose whether the output rail floats or is actively pulled low when the switch is disabled. Typical applications include powering processor cores and I/O rails in servers and SSDs, peripheral port power control in industrial systems, and general 5V-rail power distribution where a compact 6 A switch replaces discrete MOSFET-plus-driver solutions. When designing with the TPS22992, account for thermal rise at sustained high load: at 6 A, I2R losses through the 8.7 mΩ switch demand a solid ground-plane copper pour under the WQFN-HR thermal pad to keep junction temperature within limits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22995RZGR - 3.8A, 5.5V Load Switch 18mΩ | TI
TPS22995RZGR

TPS22995RZGR - 3.8A, 5.5V Load Switch 18mΩ | TI

The Texas Instruments TPS22995RZGR is a single-channel N-channel high-side load switch with a maximum continuous current of 3.8 A, a typical on-resistance of 18 mΩ, and an input operating voltage range of 0.4 V to 5.5 V, housed in a 6-pin WQFN-HR (RZG) package measuring just 1.5 mm x 0.75 mm. A load switch is a type of power distribution switch, which itself sits within the broader power management IC hierarchy. Load switches use an integrated MOSFET pass element controlled by a logic input to connect or disconnect a power rail from its load, enabling power sequencing, rail gating, and inrush-current control in multi-rail systems. The TPS22995 implements this function with a low-resistance N-channel MOSFET that reduces dropout voltage for low-voltage, high-current rails. Key features include the 0.4 V to 5.5 V VIN range, a separate bias supply (VBIAS) operating from 1.5 V to 5.5 V that fully enhances the N-channel MOSFET even at very low input voltages, and adjustable output slew-rate control through an external capacitor on the CT pin. The adjustable rise time enables precise power-on sequencing and limits inrush current during startup, protecting upstream regulators and connectors. Technically, the device achieves its 18 mΩ typical on-resistance by driving the N-channel pass transistor gate above the input rail using the bias supply. This architecture yields very low voltage drop at multi-ampere loads, minimizing power loss (I²R) and thermal stress. Typical on-resistance keeps dissipation low: at 3.8 A the conduction loss is only about 0.26 W (Estimated: I²R = 3.8² x 0.018). Typical applications include power rail gating in battery-powered portable electronics, SSD and storage peripherals, micro-IoT hardware with limited PCB real estate, and industrial point-of-load distribution where a small, low-loss switch is required. When designing with this device, always provide the VBIAS supply (1.5 V to 5.5 V) with local decoupling, and size the CT capacitor to set the rise time appropriate for the load capacitance to control inrush current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS22997QRYZRQ1 - 10A, 5.5V Load Switch | Texas Instruments
TPS22997QRYZRQ1

TPS22997QRYZRQ1 - 10A, 5.5V Load Switch | Texas Instruments

The Texas Instruments TPS22997QRYZRQ1 is an AEC-Q100 qualified single-channel automotive load switch delivering up to 10A continuous current over an input voltage range of 0.1V to 5.5V, with a bias supply of 1.5V to 5.5V. It integrates an N-channel MOSFET with a typical on-resistance of only 4 mΩ in a compact 10-pin WQFN-HR (RYZ) package measuring just 1.5 mm x 2 mm. A load switch is a power management IC that gates a power rail on and off using an integrated MOSFET controlled by a logic-level enable pin. In the power management hierarchy, load switches sit between the power source (a DC-DC converter or LDO) and the load, providing controlled power-up sequencing, inrush limiting, rail isolation, and fault protection that raw converters do not offer. Key features include adjustable slew-rate control to minimize inrush current during turn-on, an adjustable quick output discharge (QOD) pin that actively pulls the output low when disabled, and a power-good output for rail monitoring and sequencing. The ON pin can interface directly with low-voltage GPIO signals. Thermal shutdown and low quiescent power consumption round out the feature set. Technically, the 4 mΩ RON translates to only 40 mV of drop at 10A and just 0.4W of conduction loss, eliminating the need for a heatsink. The configurable rise time allows designers to trade startup time against inrush current to protect upstream regulators and downstream capacitors. Typical applications include automotive ADAS processor and FPGA power sequencing, infotainment rail gating, sensor module power control, and battery-connected load management in 5V and sub-5V systems. The Q1 qualification supports all AEC-Q100 automotive ambient temperature grades. Design tip: use the CT pin capacitor to set slew rate so that inrush into large downstream bulk capacitance stays within the upstream supply current limit, and verify bias voltage is present before asserting ON.

RFQ پەیوەندی
TPS22997RYZR - 5.5V 10A 4mOhm Load Switch | Texas Instruments
TPS22997RYZR

TPS22997RYZR - 5.5V 10A 4mOhm Load Switch | Texas Instruments

The Texas Instruments TPS22997RYZR is a single-channel load switch with an integrated N-channel MOSFET, operating over an input voltage range of 0.1 V to 5.5 V and supporting a maximum continuous current of 10 A, with a typical on-resistance of 4 mOhm. It is housed in a compact 10-WQFN-HR (1.5x2 mm) package designed for space-constrained, high-current power distribution. A load switch is a semiconductor device that connects or disconnects a power supply rail from a load, functioning as an electronic switch. It typically integrates a pass MOSFET, gate-drive control logic, and protection features such as thermal shutdown and inrush management. Load switches sit within the power management IC hierarchy alongside hot-swap controllers and eFuses, and are essential for power gating, rail sequencing, and protection in systems from smartphones to industrial equipment. Key features include adjustable slew rate control to minimize inrush current during turn-on, adjustable quick output discharge (QOD) for rapid discharge of output capacitance, and a power good (PG) signal for rail monitoring. The enable pin (ON) interfaces directly with low-voltage GPIO signals, and the device offers thermal shutdown protection and low power consumption. The bias voltage range of 1.5 V to 5.5 V ensures compatibility with standard logic levels in mixed-voltage systems. Technically, the TPS22997 integrates a very low on-resistance N-channel MOSFET, achieving 4 mOhm typical RON, which minimizes voltage drop and conduction loss - critical at 10 A loads where even milliohms matter (4 mOhm x 10 A = 40 mV drop and 0.4 W dissipation). The configurable rise time allows designers to tailor inrush current to upstream supply capability and load capacitance, reducing supply droop and board stress. Typical applications include power distribution in SSDs, smartphones, tablets, and other portable and battery-powered devices, as well as hot-swap and load-switching functions in industrial systems. The low RON and high current capability suit high-current low-voltage rails, while the tiny 1.5x2 mm footprint saves board space. When designing with the TPS22997, provide adequate PCB copper area for thermal dissipation at full 10 A load, place decoupling capacitors close to VIN and VBIAS, and set the slew rate to balance inrush current against turn-on delay for the specific load capacitance.

RFQ پەیوەندی
TPS2370D - IEEE 802.3af PoE Power Interface Switch | TI
TPS2370D

TPS2370D - IEEE 802.3af PoE Power Interface Switch | TI

Texas Instruments TPS2370D is an IEEE 802.3af Power-over-Ethernet power interface switch for powered devices, presented in an 8-pin SOIC package. It integrates the input protection and power-signaling functions needed to connect a PoE powered device to compliant Ethernet infrastructure. The device is intended for 12.5 W-class PoE systems and helps separate the low-power Ethernet data path from the higher-voltage power path before downstream DC/DC conversion. A PoE power interface switch is the bridge between an Ethernet cable and a powered-device power supply. Ethernet carries data and power on the same cable, so the powered device must identify the available power source, control the connection, and protect the interface before accepting power. The TPS2370D is designed around IEEE 802.3af-compatible PoE powered-device behavior and is suitable for IP phones, wireless access points, surveillance equipment, and other network peripherals. The manufacturer product page identifies TPS2370 as an IEEE 802.3af power interface switch for PoE powered devices. Distributor listings identify TPS2370D as an 8-SOIC device. The verified data does not provide a complete electrical table, so ratings such as input voltage range, current limit, channel timing, protection thresholds, and temperature limits must be taken directly from the manufacturer datasheet before final design release. Those unprovided values are intentionally not inferred here. The TPS2370D belongs to the PoE interface-controller category, which sits between Ethernet connectivity and downstream power management. It is not a general-purpose voltage regulator or a DC/DC converter. A typical design uses the device at the Ethernet connector or PoE input, then passes the selected power to a DC/DC converter that creates the low-voltage rails required by the powered device. For a new PoE design, verify connector pinout, cable polarity protection, isolation requirements, thermal performance, and the IEEE 802.3af power-class limits against the current TI documentation. The D suffix denotes the verified 8-SOIC ordering variant, while package-specific land patterns and exposed-pad details must be confirmed from the package drawing rather than inferred from generic SOIC drawings. This product page consolidates the verified manufacturer identification, package information, distributor data, and cross-reference findings. It deliberately distinguishes confirmed facts from parameters requiring the datasheet, which helps engineers evaluate sourcing without treating unverified electrical claims as design data.

RFQ پەیوەندی
TPS2370DR - IEEE 802.3af PoE Power Interface Switch | Texas Instruments
TPS2370DR

TPS2370DR - IEEE 802.3af PoE Power Interface Switch | Texas Instruments

The Texas Instruments TPS2370DR is an IEEE 802.3af power interface switch for Power over Ethernet powered devices, supplied in an 8-pin SOIC package. The verified listing identifies its role as a PoE power-interface switch, while the available data does not specify its operating voltage, current, protection thresholds, temperature range, or exact electrical limits. A PoE power interface switch is the component that connects a powered device to the power delivered through an Ethernet cable. It sits in the power path after cable-side network isolation and helps a powered device receive or reject power according to the Ethernet PoE system. In this product family, the TPS2370 is specifically identified as an IEEE 802.3af power interface switch for PoE powered devices. The principal verified feature is IEEE 802.3af compatibility. This standard is associated with 10/100/1000BASE-T Ethernet applications and defines the framework for supplying power over standard Ethernet cabling. The TPS2370DR therefore targets networking equipment that needs a dedicated PoE interface rather than a general-purpose voltage regulator or conventional power switch. The TPS2370DR uses Texas Instruments’ DR package designation, identified in the supplied results as an 8-SOIC or SOP8 package. Surface-mount construction supports compact PCB layouts, while the eight-pin package leaves the device easy to inspect and replace during manufacturing. The verified distributor information also classifies it as a specialized interface IC and power-supply support circuit. Typical application areas include PoE-powered network cameras, VoIP phones, wireless access points, Ethernet switches, and other powered devices connected through Ethernet infrastructure. The exact power budget, current handling, protection behavior, and thermal performance must be confirmed from the manufacturer datasheet before final circuit design. This page preserves the verified product identity and distinguishes it from functionally similar, but not necessarily pin-compatible, alternatives.

RFQ پەیوەندی
TPS2370PW - IEEE 802.3af PoE PD Interface, 8-TSSOP | Texas Instruments
TPS2370PW

TPS2370PW - IEEE 802.3af PoE PD Interface, 8-TSSOP | Texas Instruments

The Texas Instruments TPS2370PW is an IEEE 802.3af-compliant Power Interface Switch for Power-over-Ethernet (PoE) Powered Devices (PDs), integrating detection, classification, inrush current limiting, and a 0.3-ohm internal pass FET into a single 8-pin TSSOP (PW) package. It acts as the interface between the Power Sourcing Equipment (PSE) and the powered device, performing all functions required by the IEEE 802.3af standard. The device supports input voltages up to 67 V from the Ethernet cable and includes a 100 V rated internal switch. A PoE PD controller is a specialized power management integrated circuit that handles the front-end handshake between a PoE-enabled switch (PSE) and the device receiving power (PD). It detects a valid 25 kohm signature resistor, classifies the PD into one of five power classes (0-4) under the IEEE 802.3af spec, controls inrush current with a soft-start mechanism, and finally applies power through an integrated low-RDS(on) MOSFET. The TPS2370 occupies the power management IC hierarchy between simple hot-swap controllers and full PoE+ (802.3at) Type 2 controllers, representing the original-generation 802.3af building block. Key features include a 0.3-ohm internal pass MOSFET, programmable inrush current limiting, integrated detection signature circuitry, automatic classification signature generation, and an open-drain power-good output indicator. The 8-pin TSSOP package enables compact front-end designs for IP phones, wireless access points, and security cameras where PCB real estate is at a premium. The device operates from the 48 V nominal PoE rail but tolerates transients consistent with cable discharge events. The architecture uses a precision bandgap reference and comparators to implement the IEEE 802.3af detection signature (25 kohm equivalent resistance), and a current-mode control loop for inrush limiting. Once classification completes, the internal 100 V N-channel MOSFET is fully enhanced, minimizing DC losses. Logic-level interfaces provide ground-referred status and enable signals for downstream DC-DC converters. Typical applications include VoIP phones, wireless access points (Wi-Fi APs), IP security cameras, RFID readers, and any low-power 802.3af-compliant PD that derives its primary supply from a PoE line. Industrial sensors and building automation endpoints also benefit from single-cable power-and-data deployment enabled by this controller. When designing with this part, follow IEEE 802.3af detection and classification timing budgets closely; bypass the device with a TVS diode for cable discharge protection, and select the input bulk capacitor and inrush timing components per the datasheet's typical application circuit to avoid re-triggering detection during power-up. This page synthesizes distributor availability, drop-in alternatives to other 8-pin TSSOP PoE PD controllers, and practical layout considerations that go beyond the datasheet's typical application drawings.

RFQ پەیوەندی
TPS2370PWG4 - IEEE 802.3af PoE PD Power Interface Switch | TI
TPS2370PWG4

TPS2370PWG4 - IEEE 802.3af PoE PD Power Interface Switch | TI

The Texas Instruments TPS2370PWG4 is an IEEE 802.3af-compliant Power-over-Ethernet (PoE) Powered Device (PD) interface switch integrating detection, classification, inrush current limiting, and a 0.3-ohm internal pass FET in a single 8-pin TSSOP package. It operates across the standard 48V PoE supply rail, performs the four-quadrant detection signature required by IEEE 802.3af, and delivers up to 13 W of available PD power through a programmable inrush current limit rather than relying solely on the 400 mA / 50 ms default limit. A Power-over-Ethernet PD controller is a specialized power management IC that sits between an Ethernet RJ-45 connector and a downstream DC-DC converter, presenting the standardized 25 kohm detection signature, the 4-step classification current, and the inrush/turn-on behavior mandated by IEEE 802.3af. In the broader taxonomy, the TPS2370 sits under Power Management IC -> Hot Swap / Power Interface Switch -> PoE PD Controller. It off-loads the thermal stress of the hot-swap FET to an internal MOSFET while exposing only a few pins to the system designer. Key features include the integrated 0.3-ohm MOSFET that eliminates an external switch, a programmable inrush current limit that lifts the ~180 uF cap-size restriction of the bare IEEE 802.3af timing, open-drain PG (power good) and PG_OFF flags for sequencing downstream converters, and an adjustable UVLO for non-standard PoE inputs. The TSSOP-8 footprint keeps the solution under 5 x 7 mm of board area, which is important for compact IP phones, wireless access points, and small surveillance cameras. Architecturally the TPS2370 combines a precision 25 kohm detection resistor network (internal), a class-current reference, a gate-charge-pumped 100 V-rated internal MOSFET, and a thermal shutdown block. Compared with discrete implementations using a hot-swap controller plus a FET plus a sense resistor, the integration reduces BOM cost by typically three parts and improves accuracy because the detection signature tracks the internal FET's on-resistance instead of an external resistor pair. Typical applications include IP phones, wireless access points, IP security cameras, IoT gateways, and any 802.3af-powered sensor or access device where a single Ethernet cable must supply both data and power. The device is also widely used as a front-end for non-PoE products that benefit from the integrated inrush and isolation coordination. When designing with the TPS2370PWG4, treat VDD-VSS as the PoE input rail directly and place the input capacitance close to those pins; downstream of the TPS2370 the rail goes to a DC-DC converter that produces the final logic voltage. The PG output can be used to enable the downstream converter only after the bulk capacitor has fully charged, eliminating the start-up overshoot common to PoE loads. This page synthesizes distributor pricing, drop-in alternatives, PoE compliance design notes, and pin-level sequencing guidance not collected in a single place in the manufacturer datasheet, giving design and procurement engineers a one-pass reference.

RFQ پەیوەندی
TPS2370PWR - IEEE 802.3af PoE PD Interface Switch | Texas Instruments
TPS2370PWR

TPS2370PWR - IEEE 802.3af PoE PD Interface Switch | Texas Instruments

The Texas Instruments TPS2370PWR is an IEEE 802.3af Power Interface Switch for Power-over-Ethernet (PoE) Powered Devices (PD), integrating detection, classification, inrush current limiting and pass-FET control in an 8-pin TSSOP (PW) package. The part implements the physical-layer PD interface between the Ethernet RJ-45 and the downstream DC-DC converter, supporting the full 802.3af handshake with an internal 0.3-ohm low-side N-channel FET and a 100 V abs-max VPD input rating. A PoE Powered Device Controller is a specialized interface IC that sits between the Power Sourcing Equipment (PSE) on the Ethernet switch and the application load. It performs the signature resistance, power classification (Class 0-4) and inrush-limited hot-swap turn-on mandated by IEEE 802.3af, then hands a regulated bulk rail to a downstream DC-DC converter. Within the broader Power-over-Ethernet taxonomy, the TPS2370PWR belongs to the PD controller category, which complements PSE controllers and DC-DC converters to form a complete PoE end-to-end solution. Key features include 0.3-ohm internal FET on-resistance for low conduction loss, 100 V maximum input voltage on VPD for surge margin, integrated IEEE 802.3af detection signature (24.9 kohm) and classification current sourcing, programmable inrush current limiting via an external gate capacitor, and a complementary open-drain PG (power-good) output for sequencing the downstream converter. Above 20 V input the classification current is shut off to reduce internal dissipation, and an internal undervoltage lockout prevents turn-on below the 802.3af minimum operate voltage. The architecture combines a precision bandgap reference, current-mode signature generation and a gated low-side MOSFET driver. By driving only the return-side FET, the TPS2370PWR allows the upstream PSE to maintain the PoE pair-to-pair voltage regardless of PD load transients. The 8-pin TSSOP body keeps the thermal path short, and the device is rated for the industrial -40C to +85C operating range required for outdoor and industrial Power-over-Ethernet endpoints. Typical applications include VoIP telephones, wireless LAN access points, IP security cameras, IoT gateways and industrial sensors that draw their power from the Ethernet cable rather than a separate wall adapter. Placing the TPS2370PWR upstream of a wide-input DC-DC converter is the canonical architecture for any 802.3af-compliant PD. When designing with this part, ensure the inrush gate capacitor is sized for the downstream bulk capacitance to keep inrush current within the 802.3af limit, and verify the transformer bridge is 802.3af compliant with the required center-tap connection. A TVS diode on VPD is strongly recommended for surge robustness above the 100 V abs-max. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical PoE design notes not found on a single manufacturer page.

RFQ پەیوەندی
TPS2371PW - PoE PD Power Interface Switch, IEEE 802.3af | TI
TPS2371PW

TPS2371PW - PoE PD Power Interface Switch, IEEE 802.3af | TI

The Texas Instruments TPS2371PW is a legacy/IEEE 802.3af-compatible Power-over-Ethernet (PoE) Powered Device (PD) power interface switch, integrating the input detection, classification, and inrush control functions required by the 802.3af standard. It packages a 100 V-rated internal low-side pass FET (return-side switch) in an 8-pin TSSOP (PW) footprint. A PoE PD interface controller is a specialized power management IC that handles the negotiation and power-path startup between a Power Sourcing Equipment (PSE) and a powered load. The TPS2371 sits between the Ethernet RJ-45 magnetics and the DC-DC converter that follows it, performing signature detection (25 kΩ resistor presentation), classification (one of Class 0-4 current signatures), and inrush-limited turn-on of the bulk input capacitor. This functional block sits within the broader power management IC hierarchy, which includes voltage regulators, supervisors, and DC-DC converters. Key features include 100 V absolute maximum input voltage on the VDD pin, programmable inrush current limiting via an external resistor, automatic classification current shutoff above 20 V to reduce internal dissipation, and support for both current- and voltage-mode classification schemes. The internal N-channel FET has a typical on-resistance of 1 Ω and supports continuous currents up to 0.5 A at the return side, with transient capability to 1.5 A. The TPS2371 is designed to operate from a single twisted-pair or 4-pair Ethernet input. The low-side (return-side) topology allows the upstream DC-DC converter to use a non-isolated buck or a flyback configuration tied to chassis ground. Internal protection includes thermal shutdown, input undervoltage lockout, and a 100 V surge-tolerant drain connection. Typical applications include 802.3af-compliant PoE PD endpoints such as wireless access points, VoIP phones, IP cameras, IoT sensors, and low-power industrial Ethernet nodes. Designers benefit from a reduced BOM by eliminating external pass-MOSFETs and discrete signature resistors, while the TSSOP-8 package supports automated assembly. When designing with this part, ensure the upstream Ethernet physical layer (PHY) magnetics provide the proper center-tap injection point to the VDD pin, and verify that the downstream DC-DC startup current draw does not exceed the configured inrush limit. The 8-pin TSSOP (PW) is a thermally enhanced package but still requires adequate copper pour for sustained high-current operation.

RFQ پەیوەندی
TPS2371PWR - Legacy PoE Power Interface Switch | TI
TPS2371PWR

TPS2371PWR - Legacy PoE Power Interface Switch | TI

The Texas Instruments TPS2371PWR is a legacy IEEE 802.3af-compatible power interface switch for Power over Ethernet powered devices, with programmable inrush current limiting and an 8-pin TSSOP package. It is designed for PoE PD applications requiring controlled power admission, input protection, and startup behavior. A power interface switch is an integrated semiconductor that sits between a PoE source and the powered equipment. It controls how power is applied to the downstream circuit, helping prevent excessive startup current, protecting source equipment, and defining the operating conditions seen by the load. In the broader power-management hierarchy, this device belongs to the PoE interface-switch and power-management IC category rather than a conventional voltage regulator. The verified manufacturer information identifies the TPS2371 as a legacy IEEE 802.3af-compatible power interface switch for PoE PDs. The datasheet search result also states that IEEE 802.3af permits an inrush current of 400 mA for 50 ms, limiting the load capacitor to approximately 180 µF. The programmable inrush current limit removes that restriction and permits a larger capacitor with lower startup current. The key design trade-off is between fast startup and controlled power admission. A lower programmed inrush limit can reduce stress on the PoE source and downstream components but may lengthen startup, while a higher limit can start a larger load more quickly but places greater transient demand on the source. The device is intended to simplify legacy PoE PD power-interface designs while preserving the external 8-TSSOP footprint. Typical applications include legacy PoE powered devices, powered Ethernet endpoints, IP cameras, VoIP phones, access-point equipment, and other IEEE 802.3af-compatible PDs. The part should be selected only after checking the source's PoE classification, available power, startup timing, protection requirements, and downstream capacitance against the complete manufacturer datasheet. For implementation, follow the manufacturer application guidance for input capacitance, current-limit programming, surge protection, layout, and exposed-pad or thermal requirements where applicable. Do not infer ratings, thresholds, or timing values from distributor descriptions alone; verify them in the official TPS2371 datasheet before releasing a production design. This page consolidates verified manufacturer and distributor descriptions, separates documented facts from unavailable parameters, and provides engineering guidance for comparing this legacy PoE interface switch with possible replacements.

RFQ پەیوەندی
TPS2372-3RGWT - 802.3bt PoE PD Controller 60W | Texas Instruments
TPS2372-3RGWT

TPS2372-3RGWT - 802.3bt PoE PD Controller 60W | Texas Instruments

The Texas Instruments TPS2372-3RGWT is an IEEE 802.3at and IEEE 802.3bt high-power Power over Ethernet (PoE) powered device (PD) interface controller supporting up to 60 W (Type 3) in a 20-pin VQFN (RGW) 5x5 mm package. A PoE PD interface controller is the front-end power management IC that resides in the powered device of a PoE system. It performs detection, classification, inrush current limiting, and disconnect identification, then hands off power to an isolated or non-isolated DC-DC converter. It sits at the top of the PoE power hierarchy: PoE PD controller -> PoE power interface IC -> power management IC -> semiconductor. Key features include support for IEEE 802.3at (Type 2) and IEEE 802.3bt (Type 1-4) classes, Automatic MPS (Maintain Power Signature) that reduces standby power in battery-backed applications, and Autoclass that enables downstream converters to lower power losses. Protection circuits cover undervoltage lockout, overcurrent, and thermal shutdown. PGOOD status indication allows clean sequencing of the downstream converter. The TPS2372-3 variant is optimized for 60 W applications with low internal switch resistance, while the TPS2372-4 variant supports up to 90 W Type 4 designs. According to the Texas Instruments product page, the TPS2372 family contains all features needed to implement an IEEE 802.3at or 802.3bt (draft) Type 1-4 powered device. Detection and classification compliance ensures interoperability with all standard PSE (power sourcing equipment) vendors. Typical applications include LED lighting fixtures, IP security cameras, wireless access points, 5G small cells, VoIP telephones, and network switches. Its wide input tolerance (0 V to 57 V per distributor data) and integrated pass transistor reduce bill-of-materials count versus discrete MOSFET solutions. For design, budget the inrush current limit against downstream converter input capacitance, and use the PGOOD output to enable the converter only after PoE handshake completes. This page adds distributor pricing, drop-in alternatives, and practical design notes beyond the manufacturer datasheet.

RFQ پەیوەندی
TPS2372-4RGWT - IEEE 802.3bt PoE PD Controller 90W | TI
TPS2372-4RGWT

TPS2372-4RGWT - IEEE 802.3bt PoE PD Controller 90W | TI

The Texas Instruments TPS2372-4RGWT is a 1-channel IEEE 802.3bt (Type 1-4) Power over Ethernet powered-device (PD) interface controller supporting up to 90 W, with an integrated low-RDS(on) internal pass switch, supplied from 0 V to 57 V in a 20-pin VQFN (5x5 mm) package with exposed pad. A PoE PD controller is the front-end power-management IC that resides inside a powered device such as an IP camera, wireless access point, or LED luminaire. It performs detection, classification, and inrush-current limiting so the power-sourcing equipment (PSE) in the network switch can safely identify and power the device over the Ethernet cable. Within the power-management hierarchy, it sits between the RJ45 magnetics/diode bridge and the isolated DC-DC converter that generates the system rails. Key features of the TPS2372-4 include support for IEEE 802.3at (PoE+) and 802.3bt draft Type 1-4 power classes, Automatic MPS to maintain power through low-load periods, and Autoclass for accurate power allocation reporting to the PSE. The -4 variant's low internal switch resistance enables full 90 W Type 4 operation, while the related TPS2372-3 supports up to 60 W. Technically, the device integrates the detection and classification signature resistors, a hot-swap MOSFET with current limiting, thermal protection, and fault supervision. The low switch resistance minimizes conduction losses at the multi-ampere input currents demanded by Type 3 and Type 4 systems, improving overall efficiency and reducing heatsinking requirements. Typical applications include 802.3bt high-power LED lighting, 5G small cells and wireless access points, PTZ IP security cameras, and industrial networked devices where a single Ethernet cable delivers both data and up to 90 W of power. When designing, place the IEEE signature components (the 24.9 k-ohm detection resistor and classification resistors) directly at the VDD/RTN pins, and verify the inrush and operating current limits against your isolated converter's input capacitance to avoid nuisance tripping during startup. This page synthesizes distributor availability, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS23730RMTR - 802.3bt PoE PD Controller 60W | Texas Instruments
TPS23730RMTR

TPS23730RMTR - 802.3bt PoE PD Controller 60W | Texas Instruments

The Texas Instruments TPS23730RMTR is an IEEE 802.3bt Type 3 (Class 1-6) Power over Ethernet powered-device (PD) controller with an integrated high-efficiency current-mode DC-DC controller, supplied in a 45-pin VQFN (RMT) package measuring 7x5 mm and rated from -40C to +125C. It integrates a robust 100-V, 0.3-ohm (typ) hotswap MOSFET and supports power levels up to 60 W, and is EA Gen 2 logo-ready as a PoE 2 PD controller. A PoE PD controller is the interface IC that negotiates power with a Power Sourcing Equipment (PSE) port, performs detection, classification, and inrush current limiting, then hands off to a DC-DC converter that produces the equipment's usable rails. Within the power-management hierarchy it spans both the PoE interface layer and the switching-regulator control layer, replacing the two-chip discrete solutions used in earlier 802.3at designs. Key differentiating features include complete single-chip 802.3bt Type 3 compliance for Class 1-6 power levels, an allocated power indicator output, support for parallel or split power operation, and a current-mode controller optimized for both flyback and active-clamp forward (ACF) topologies. The integrated 100-V hotswap MOSFET with 0.3-ohm on-resistance removes an external pass device, reducing BOM count and conduction losses at multi-amp input currents. On the technical side, the DC-DC controller section supports high-efficiency isolated and non-isolated conversions from the 48-V PoE rail, with current-mode control providing inherent cycle-by-cycle current limiting and simple loop compensation. EA Gen 2 (PoE 2) readiness means the TPS23730 passes certification requirements for next-generation high-power PoE deployments, supporting up to 60 W at the PD for Type 3 Class 6 operation. Typical applications include 5G small-cell radios and network cameras that draw 40-60 W, wireless access points, LED lighting drivers powered from Ethernet, and industrial IP intercom or display terminals where a single Cat5e cable must carry both data and power. The 60-W envelope with allocated power indicator outputs makes it particularly suitable for two-pair Type 3 PD designs. Design-wise, validate the transformer or forward magnetics for the full Class 6 power level and provide adequate PCB copper under the RMT exposed pad for hotswap MOSFET conduction and switching losses; TI's TPS23730EVM-093 reference design is the recommended starting point for new layouts. This page synthesizes distributor pricing, lifecycle data, and application guidance not found in a single manufacturer datasheet.

RFQ پەیوەندی
TPS23734RMTR - IEEE 802.3bt Type 3 PoE PD Controller | TI
TPS23734RMTR

TPS23734RMTR - IEEE 802.3bt Type 3 PoE PD Controller | TI

The Texas Instruments TPS23734RMTR is an IEEE 802.3bt Type 3 Class 1-4 Power-over-Ethernet (PoE) Powered Device (PD) controller with an integrated high-efficiency DC-DC controller, housed in a 45-pin VQFN (RMT) package measuring 7 mm x 5 mm. As a PoE 2 / EA Gen 2 logo-ready PD controller, it includes a robust 0.3 ohm (typical) internal hotswap MOSFET and supports power levels up to 30 W operation across 802.3bt Type 3 and 802.3at PD applications. The device integrates an internal PWM controller intended for flyback or active-clamp forward primary-side-regulated DC-DC topologies, eliminating the need for an opto-isolator and significantly simplifying isolated PoE supply designs. An IEEE 802.3bt PD controller is a specialized interface IC that negotiates power classification with a Power Sourcing Equipment (PSE) over twisted-pair Ethernet cabling, then converts the incoming PoE voltage into a regulated supply rail for downstream loads. These devices sit at the front end of PD hardware such as IP phones, wireless access points, security cameras, and IoT gateways, and they bridge the PoE interface standard with the application board. Within a power-management taxonomy the TPS23734 is part of: PoE PD controller -> Power-over-Ethernet IC -> Power Management Interface IC -> Power Management -> Semiconductor. Key differentiating features of the TPS23734RMTR include integrated primary-side regulation (PSR) which removes the secondary-side feedback optocoupler and TL431, an automotive temperature grade of -40 C to +125 C, and EA Gen 2 logo-ready compliance with the IEEE 802.3bt specification. The internal hotswap FET minimizes external component count and the device supports all five 802.3bt classes (Class 1 through Class 4), enabling a single PCB design to address 15 W, 30 W, and intermediate power levels in the same hardware platform. The architecture pairs a hardened PoE interface front-end (signature, classification, and inrush control) with an integrated current-mode PWM controller optimized for high-efficiency flyback conversion. Primary-side regulation samples auxiliary winding voltage during the MOSFET off-time to close the loop without secondary-side feedback parts. This topology reduces BOM cost, improves MTBF, and avoids the bandwidth and aging limitations of opto-isolated feedback. Typical applications for the TPS23734RMTR include PoE-powered wireless access points (Wi-Fi 6/6E APs), IP surveillance cameras, VoIP phones, IoT and smart-building sensors, and industrial PoE-powered controllers where isolated, regulated 5 V, 12 V, or 24 V rails are required from 42-57 V PoE inputs. Up to 30 W operation covers most single-board PoE appliances. When designing with this device, pay close attention to the transformer design for PSR applications - the auxiliary winding ratio directly sets output voltage accuracy, and proper RCD snubber sizing is essential for efficiency. Layout should keep the hotswap path short and place the bootstrap capacitor immediately adjacent to the BOOT pin to avoid PWM-controller UVLO. Operating ambient temperature may limit output power; derate using the application-specific thermal profile. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not consolidated in the manufacturer datasheet, giving engineers an actionable reference for selecting the TPS23734RMTR in new PoE PD designs.

RFQ پەیوەندی
TPS23758RJJR - IEEE 802.3at PoE PD Flyback Controller | TI
TPS23758RJJR

TPS23758RJJR - IEEE 802.3at PoE PD Flyback Controller | TI

The Texas Instruments TPS23758RJJR is an IEEE 802.3at Power over Ethernet (PoE) powered-device (PD) controller with an integrated 150-V power FET and a current-mode, no-opto synchronous flyback DC-DC controller, housed in a 24-pin VSON (6 mm x 4 mm) surface-mount package. It supports 802.3at Type 1 power levels up to 13 W from the PoE link. A PoE PD interface is the circuit that negotiates and extracts power from Ethernet cabling per IEEE 802.3at, sitting within the hierarchy of power management ICs (PoE controller -> power interface -> power management IC -> semiconductor). It performs detection, classification, inrush control, and load switching for devices powered over the data cable, such as IP cameras and wireless access points. Key differentiating features include high integration: the TPS23758 combines the PD interface, a 150-V switching power FET, and the DC-DC controller in one die set, reducing external component count. Primary-side regulation (PSR) eliminates the optocoupler and secondary-side feedback network, while spread spectrum frequency dithering (SSFD) reduces EMI peak emissions. Advanced startup supports efficient boot sequencing from the PoE input. Technically, the device operates as a current-mode flyback controller optimized for isolated or non-isolated PoE conversion topologies. The no-opto sync architecture uses transformer auxiliary-winding sensing for output regulation, improving reliability and shrinking the solution footprint compared with conventional optocoupler flybacks. The integrated 150-V FET withstands PoE input transients common on long cable runs. Typical applications include IEEE 802.3at Type 1 (13 W) IP network cameras, wireless access points, VoIP phones, and other size-constrained PoE-powered endpoints where board space and EMI compliance are critical constraints. A key design consideration is transformer selection: the no-opto PSR scheme depends on accurate auxiliary-winding design, and TI recommends following the TPS23758EVM-080 reference design transformer specification for Type 1 applications. This page synthesizes distributor inventory data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TPS2375PW-1 - IEEE 802.3af PoE PD Controller, 100V | Texas Instruments
TPS2375PW-1

TPS2375PW-1 - IEEE 802.3af PoE PD Controller, 100V | Texas Instruments

The Texas Instruments TPS2375PW-1 is an IEEE 802.3af Power over Ethernet (PoE) Powered Device (PD) controller with auto-retry fault recovery, a 100-V rating, and a true open-drain power-good output, housed in an 8-pin TSSOP (PW) package rated for operation from -40C to +85C. Power over Ethernet is a technology defined by the IEEE 802.3af standard that delivers DC power alongside data over standard Category 5 Ethernet cabling. A PoE system consists of Power Sourcing Equipment (PSE), such as a PoE switch or midspan injector, and a Powered Device (PD), such as an IP camera, wireless access point, or VoIP phone. The PD controller is the interface IC that performs detection, classification, and inrush-current control so the PSE can safely identify and power the end device. It sits at the entry point of the PD power path, ahead of the isolated DC-DC converter that generates the system rails, and therefore forms part of the broader power management IC hierarchy. Key features of the TPS2375PW-1 include full compliance with the IEEE 802.3af specification, with device thresholds offset by 1.5 V from the standard to account for input diode-bridge drops, ensuring polarity-insensitive operation. The -1 suffix denotes second-generation silicon with a 100-V absolute maximum rating and a true open-drain power-good (PGB) output. Its defining differentiator is auto-retry: after an overcurrent fault, the device automatically attempts to re-enable the pass MOSFET instead of latching off, eliminating the need for a power cycle. An integrated 0.58-ohm sense element plus classification resistor support (Class 0-3, up to 12.95 W at the PD) reduces external component count. Architecturally, the controller integrates the detection and classification signature circuits, a 57-V rated hot-swap pass-element gate driver, current-limit and foldback protection, and thermal shutdown. The DETC pin manages detection behavior and the CLS pin programs the power class. During startup, controlled gate slew limits inrush current so the PSE is not tripped by capacitor charging; during a fault, the current limit engages and the auto-retry timer restarts the pass element once the fault clears. Typical applications include IP network cameras, 802.11 wireless access points, VoIP telephones, and PoE-enabled lighting or access-control nodes - anywhere a device must draw 13 W or less from an Ethernet port. The part pairs naturally with a flyback or forward converter to generate isolated low-voltage rails. A key design consideration is sizing the bulk input capacitance so inrush stays within the PSE inrush budget, and ensuring the external pass MOSFET and TVS diode meet the 100-V transient environment. Prices on this page are as of 2026-10-19 (LCSC from $2.3057). This page synthesizes distributor pricing, drop-in alternatives, practical design notes, and comparison data not found in the manufacturer datasheet alone.

RFQ پەیوەندی
TPS2378DDAR - IEEE 802.3at PoE+ PD Controller 0.85A | TI
TPS2378DDAR

TPS2378DDAR - IEEE 802.3at PoE+ PD Controller 0.85A | TI

The Texas Instruments TPS2378DDAR is an IEEE 802.3at high-power Power over Ethernet (PoE) powered device (PD) interface controller that continuously handles up to 0.85 A using a low 0.5-ohm internal switch, housed in an 8-pin SO PowerPAD (DDA/HSOIC) package rated from -40C to +85C. A PoE powered device interface is the front-end circuit that lets a network-enabled product safely draw power over the same Ethernet cable that carries its data. Sitting at the top of the power management hierarchy, it performs detection, classification, inrush current limiting and load switching per the IEEE 802.3af and 802.3at standards, before handing a regulated rail to downstream DC-DC converters. The TPS2378 is TI's PD interface controller in that family. Key features include support for both IEEE 802.3at type-2 (PoE+, up to 25.5 W at the PD) and 802.3af (PoE, class 0-3) operation, an auxiliary power detect (APD) input that gives priority to an external DC supply, and the internal 0.5-ohm pass switch that eliminates a discrete MOSFET. Automatic classification with the CLS pin and a T2P output signal simplify type-2 system designs. Architecturally, the TPS2378 integrates the IEEE detection and classification state machines, a thermal shutdown, and a gate driver for the internal pass element. The PowerPAD exposed pad on the DDA package provides enhanced thermal dissipation, which is what enables continuous 0.85 A operation through an on-chip switch. The 37-page TI datasheet documents the full state machine timing and threshold levels. Typical applications include IP security cameras, wireless access points, VoIP phones, PoE lighting (LED) drivers, and networked industrial sensors that must comply with 802.3at type-2 power budgets. Design-wise, the APD feature allows the PD to prefer a wall-adapter input; tie APD appropriately if auxiliary power is not used. Verify inrush compliance (type-2 class events) during qualification. This page adds distributor pricing, drop-in alternatives, and practical design guidance beyond the TI datasheet.

RFQ پەیوەندی
TPS23881ARTQT - 8-Ch 4-Pair Type-4 PoE PSE | Texas Instruments
TPS23881ARTQT

TPS23881ARTQT - 8-Ch 4-Pair Type-4 PoE PSE | Texas Instruments

The Texas Instruments TPS23881ARTQT is a 4-pair, Type-4, 8-channel Power-over-Ethernet (PoE) Power Sourcing Equipment (PSE) controller with 200 mΩ RSENSE and autonomous I2C/manual modes, housed in a 56-pin VQFN (8x8 mm) power package rated for industrial -40°C to +125°C operation. A Power-over-Ethernet PSE controller is a specialized mixed-signal IC that sits inside an Ethernet switch, midspan, or PoE injector and safely delivers DC power over the twisted-pair cabling to a Powered Device (PD) such as a wireless AP, IP camera, or lighting fixture. In the broader hierarchy, the TPS23881ARTQT is a PoE controller -> power management IC -> power switch IC -> interface IC -> semiconductor, enabling compliance with the IEEE 802.3bt (formerly 802.3at/at+bt) standard. Key features include support for 4-pair Type-3/Type-4 operation delivering up to 90 W per port, 200 mΩ current-sense resistors per pair for accurate current monitoring, integrated 0.5 Ω MOSFET gate drivers, I2C programmability with 16 addresses, autonomous semi-auto and manual modes, comprehensive per-port telemetry (voltage, current, temperature), and legacy PD detection. The 200 mΩ RSENSE significantly reduces power dissipation versus the 0.5 Ω external FET architectures used in older PSE designs. Architecturally, the TPS23881ARTQT integrates eight independent port controllers, each containing detection, classification (including 4-event classification for Type-3/4), inrush control, and disconnect monitoring. A precision bandgap reference and on-chip ADC support accurate current/voltage measurement. The device operates from a 44 V to 57 V supply (PoE nominal 48 V) and includes per-port thermal protection and current-limit foldback. Typical applications include enterprise-class 802.3bt PoE++ switches, Wi-Fi 6/6E access points, PTZ IP cameras, PoE lighting controllers, 5G small-cell backhaul, and industrial PoE midspans. Pairing with TI's FirmPSE system firmware enables scalability to 48-port systems across multiple cascaded TPS23881 devices. When designing with this device, ensure adequate bulk capacitance on the 48 V rail, observe 4-layer PCB layout recommendations for thermal management, and reserve I2C lines for multi-device addressing. The autonomous mode reduces firmware overhead for cost-sensitive designs while the I2C interface unlocks per-port telemetry in managed switches.

RFQ پەیوەندی
TPS23881RTQR - 8-Ch 802.3bt PoE PSE Controller | Texas Instruments
TPS23881RTQR

TPS23881RTQR - 8-Ch 802.3bt PoE PSE Controller | Texas Instruments

The Texas Instruments TPS23881RTQR is an 8-channel, 4-pair, Type-4 Power-over-Ethernet (PoE) Power Sourcing Equipment (PSE) controller housed in a 56-pin VQFN (RTQ) package (8x8 mm). It complies with the IEEE 802.3bt standard, supports 200-mΩ RSENSE current sensing, and delivers up to 90 W per port across 2-pair or 4-pair configurations with auto-mode and semi-auto-mode operation. A Power-over-Ethernet PSE controller is the device that injects DC power onto Ethernet cable pairs in compliance with IEEE 802.3af/at/bt. The PSE resides inside the network switch or midspan hub and negotiates detection, classification, and inrush with the Powered Device (PD) at the far end of the cable. Within the broader system hierarchy, the TPS23881 belongs to Power Management ICs > Power Switch / Hot Swap > PoE PSE Controllers, and integrates the analog front end, MOSFET drivers, signature detection, and an I2C/SPI management interface so that an external host or firmware can configure port-by-port behavior. Key features of the TPS23881RTQR include 200-mΩ sense resistance for high-efficiency current monitoring, integrated 0.1-ohm hot-swap FETs per channel, autonomous or host-controlled port management, individual port current and voltage readback, and robust protection with current-limit, inrush timeout, and thermal shutdown. The 56-pin VQFN RTQ package with an exposed thermal pad delivers a low θJA, allowing all 8 channels to operate at 802.3bt Type-4 power levels without external heatsinking on typical 4-layer PCBs. From an architectural standpoint, the TPS23881 uses per-channel analog current-sense amplifiers and 12-bit ADC telemetry, paired with a digital control engine that runs TI's FirmPSE firmware. This dual firmware architecture allows multi-port scalability (up to 48 ports across multiple TPS23881 devices) while keeping the host CPU free for higher-layer PoE management functions. The IC supports 1-bit legacy detection, 4-point class detection, and 802.3bt multi-event classification for reliable PD discovery. Typical applications include enterprise PoE switches (up to 48 ports), industrial Ethernet switches with PoE+ or 802.3bt, IP surveillance cameras and NVR systems, wireless access points (Wi-Fi 6/6E/7), digital signage, and any switch port delivering up to 90 W over structured cabling. When designing with this part, ensure adequate copper area on the EP pad (TI recommends ≥4 thermal vias to an inner plane), follow the layout guidance in the datasheet's layout section, and size the upstream 54 V supply per the worst-case 4-pair load. Pay close attention to inrush and turn-off sequencing to avoid PD-side latch-up. This page synthesizes distributor pricing, cross-reference alternatives, and practical layout notes that extend beyond the manufacturer datasheet.

RFQ پەیوەندی