Power MOSFET Drivers
بەرهەمەکان (730+)
TJA1028TK/3V3/20/J - LIN Transceiver + 3.3V LDO SBC | NXP HVSON-8
The NXP Semiconductors TJA1028TK/3V3/20/J is a LIN 2.0/2.1/SAE J2602 and ISO 17987-4:2016 (12 V) compliant transceiver with an integrated 3.3 V low-dropout voltage regulator capable of delivering up to 70 mA, housed in an 8-pin HVSON (3x3 mm) package. It functions as a LIN Mini System Basis Chip, combining the physical layer transceiver and an MCU supply rail in a single footprint. A LIN transceiver (Local Interconnect Network transceiver) is a physical-layer device that connects a microcontroller's UART/SCI to a single-wire LIN bus used widely in automotive body electronics. The TJA1028 belongs to the SBC (System Basis Chip) product category, integrating both the bus interface and a low-dropout (LDO) voltage regulator that powers a local MCU or sensor from the vehicle's 12 V supply. SBCs sit hierarchically above LIN transceivers and below broader automotive PMICs in the power-management IC taxonomy. Key specifications include a wide battery supply range of 4.5 V to 28 V (with load-dump survival up to 42 V), an integrated 3.3 V LDO at up to 70 mA, strong ESD performance (greater than or equal to 8 kV HBM on the LIN pin), and support for both normal and low-power sleep modes. The 8-pin HVSON package offers a small 3x3 mm footprint with an exposed pad for low thermal resistance and robust PCB grounding. Internally the device integrates a LIN bus driver/receiver compliant with the LIN physical layer, a low-drop post-regulator, and mode-control logic accessed via the EN/NSTB pin. The 3.3 V LDO is stable with ceramic, tantalum, and aluminum output capacitors, simplifying BOM and enabling direct connection to a 3.3 V MCU such as NXP's S08 or Kinetis E-series. Typical applications include automotive body controllers, door/window/seat modules, HVAC sensors, steering-column switches, LIN sensor nodes (rain/light/temperature), and rear-view mirror controls. The integrated LDO eliminates an external regulator in each LIN node, reducing PCB area and BOM cost. A primary design tip is to provide adequate decoupling on the battery pin (a 100 nF ceramic close to VBAT plus a bulk capacitor on the bus supply), tie the exposed pad to a clean ground island, and use the sleep mode aggressively to keep quiescent current below the LIN network spec for current-limited nodes. This page synthesizes distributor pricing, drop-in package equivalents, and practical design notes not collated on the manufacturer datasheet alone.
TJF1052IT/2Y - Isolated CAN Transceiver, 5Mbps, SOIC-16 | NXP
The NXP TJF1052IT/2Y is a galvanically isolated high-speed CAN transceiver that delivers up to 5 Mbps data rate in a 16-pin SOIC (7.50 mm width) package with 2500 Vrms isolation rating between the CAN protocol controller and the physical two-wire CAN bus. It integrates a 2-channel digital isolator with 20 kV/µs common-mode transient immunity (CMTI) for robust operation in electrically noisy industrial environments, and supports both 3.3 V and 5 V supply rails with Normal and Standby operating modes for low-power sleep behavior. The transceiver targets industrial applications where mandated or functional isolation between bus nodes and host controllers is required to break ground loops and protect downstream logic. A CAN (Controller Area Network) transceiver is the physical-layer interface between a CAN protocol controller (typically a microcontroller's CAN peripheral or an external CAN controller) and the differential CAN_H/CAN_L bus wires. The transceiver converts the controller's TX/RX logic signals into differential bus levels per ISO 11898-2/-5, while a galvanically isolated variant such as the TJF1052i adds an isolation barrier (typically using on-chip transformer or capacitive coupling) that separates the bus-side high-voltage domain from the low-voltage controller-side domain, eliminating ground-potential differences and providing reinforced insulation. Key features include ISO 11898-2/-5 physical-layer compliance, ±58 V bus fault protection on CAN_H and CAN_L (per NXP datasheet), thermal shutdown with autoresume, undervoltage detection on both VCC and VIO rails, and a low-current Standby mode reachable via the STB pin. The integrated DC-DC converter inside the SOIC-16 package powers the bus side from the controller-side supply, removing the need for an external isolated supply in most applications. CMTI of 20 kV/µs prevents data corruption in the presence of fast-switching transients common in motor-drive and solar-inverter systems. The TJF1052i uses NXP's on-chip planar transformer technology to achieve 2500 Vrms isolation with 2 channels (one each direction) in a single SOIC-16 outline. Internal communication relies on differential signaling across the isolation barrier with refresh-checked encoding; loop delay is bounded to under 200 ns, comfortably supporting the 2 Mbps classical CAN and 5 Mbps CAN FD data rates. Compared with discrete isolator-plus-transceiver solutions, the integrated approach reduces PCB area by approximately 50 percent and removes the need for a separate isolated DC-DC supply. Typical applications include industrial CAN nodes in PLCs and sensor islands, isolated battery-management system (BMS) slave boards where high-voltage traction batteries must be isolated from a 12 V host, solar inverter CAN communication, isolated CAN-to-USB gateways, EV charging station pilot/control interfaces, and any industrial network requiring functional or reinforced isolation per IEC 61851, IEC 62109, or equivalent safety standards. The wide 3.0 V to 5.25 V VIO range also allows direct interfacing with 3.3 V microcontrollers without level shifters. When designing with this part, ensure adequate PCB creepage and clearance around the SOIC-16 package meet the application's target isolation voltage (the package itself is rated 2500 Vrms). Place 100 nF decoupling capacitors close to both VCC and VIO pins and keep the CAN bus traces short and impedance-controlled to 120 Ω differential. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
TLE6289GP - 6-Channel Peak-and-Hold Switch | Infineon
The Infineon Technologies TLE6289GP is a smart 6-channel peak-and-hold switch integrated circuit for automotive power-management and load-driving systems. The verified distributor listings identify the device as a gate-driver IC and a 6-channel peak-and-hold switch, while the available search data does not expose a complete manufacturer datasheet. Exact electrical ratings, channel logic, timing, and automotive qualification therefore require confirmation in the manufacturer datasheet before a new design is released. The GP order code denotes Infineon's automotive-oriented package family, but its exact package dimensions, pin count, and terminal assignments must also be verified against the official document. A TLE6289GP is useful where several controlled outputs must share common protection, diagnosis, or peak-and-hold behavior. Six integrated channels can reduce discrete component count and board area compared with separate switched loads, although the common-device architecture also concentrates failure and thermal-management considerations. Engineers should compare the TLE6289GP with the specific load, short-circuit, surge, and diagnostic requirements of the target vehicle platform. The verified market listings support gate-driver and power-management categorization, but they do not establish whether every output has a dedicated diagnostic path, how the channels behave during overload, or whether the device supports cascading or individual shutdown. Those details directly affect suitability in pump, motor, solenoid, relay, and electronic-valve systems. The TLE6289GP is best treated as an automotive smart-switch candidate rather than a generic MOSFET driver. Its in-circuit value depends on matching the integrated protections to the load, validating the supply and pin definitions, and checking thermal performance at the maximum simultaneous switching duty cycle. This page distinguishes verified market facts from unverified technical assumptions and identifies the parameters that still require manufacturer-source confirmation.
TLE7181EMXUMA1 - 4-Ch Half-Bridge MOSFET Gate Driver | Infineon
The Infineon TLE7181EMXUMA1 is a 4-channel half-bridge gate driver IC dedicated to driving 4 N-channel power MOSFETs forming the converter stage of high-current DC motor drives in the automotive sector. Housed in a 24-pin PG-SSOP-24-4 (exposed-pad SSOP) package with non-inverting logic, it operates from a 5.5V to 28V supply range, supports up to 1.5A peak source/sink gate drive current, and provides an SPI/digital diagnostic interface with comprehensive fault feedback. The device is AEC-Q100 qualified, making it suitable for safety-relevant automotive applications such as electric power steering (EPS), electric water pumps, engine cooling fans, and brake-by-wire actuators. A gate driver IC is a power-management semiconductor that sits between a low-power microcontroller or logic controller and the high-current gate of a power MOSFET or IGBT. Its primary function is to level-shift logic-level PWM signals to the higher voltages required to fully enhance the power MOSFET, provide high peak current to rapidly charge and discharge the gate capacitance for fast switching, and protect the controller from the high-voltage switching transients present on the half-bridge. In the broader taxonomy, gate drivers belong to the power management family, sit alongside low-side drivers, high-side drivers, and isolated gate drivers, and serve as critical building blocks in motor-control, DC-DC, and inverter subsystems. Key features of the TLE7181EMXUMA1 include four independent half-bridge outputs capable of configuring as two full H-bridges, integrated charge pump for 100% duty-cycle high-side drive, programmable dead-time generation, short-circuit and over-current detection via dedicated current-sense comparator, under-voltage lockout (UVLO) on both VCC and VBS rails, overtemperature shutdown, and a serial peripheral interface (SPI) for fault read-back and configuration. The exposed thermal pad (PG-SSOP-24-4) provides a thermal resistance of approximately 31 C/W, allowing continuous operation at moderate switching frequencies in sealed automotive environments. Typical applications include brushed DC motor control in EPS systems, brushless DC (BLDC) motor pre-drivers, electric coolant and oil pumps, HVAC blower fans, transmission solenoids, and general-purpose automotive H-bridge inverters up to several hundred watts. A PWM/DIR interface allows direct connection to a microcontroller's timer peripherals for closed-loop current or speed control. The device's 12V support and integrated protection features reduce external component count, simplifying the design of ISO 26262-compliant motor drive subsystems. When designing with the TLE7181EMXUMA1, attention must be paid to PCB layout around the bootstrap capacitors, gate-drive loop minimization, and thermal management of the exposed pad. Designers should follow Infineon's reference design and application notes to achieve robust short-circuit detection and reliable operation across the automotive -40C to +150C temperature range.
TLE7244SLXUMA2 - 8-Ch Low-Side SPI Relay Driver | Infineon
The Infineon TLE7244SLXUMA2 is an 8-channel low-side power switch in PG-SSOP-24-7 package, delivering 290 mA per channel and designed specifically as a relay driver in automotive body and chassis applications. It operates from a supply range of 5 V to 28 V (3 V to 5.5 V logic supply), provides an SPI control and diagnostic interface, and offers four direct input pins for parallel control and PWM operation. Each of the eight outputs is protected against over-current, over-temperature, and short-circuit to ground and to battery. What is a low-side SPI relay driver? A low-side power switch is a type of power distribution IC that sits between the load (typically a relay coil, solenoid, or lamp) and ground, sinking current to switch the load on or off. When controlled by an SPI (Serial Peripheral Interface) link, a single microcontroller can manage many outputs with latched commands, while the driver handles the heavy current and protective functions locally. Low-side drivers belong to the broader category of power management ICs and, more specifically, intelligent load drivers / smart power switches used in automotive electronic control units. Key features of the TLE7244SLXUMA2 include eight open-drain N-channel outputs rated at 290 mA continuous, integrated protection with current limiting and thermal shutdown per channel, an SPI interface for diagnostics and configuration, four dedicated input pins for direct control or PWM generation, a limp-home function to maintain operation under microcontroller fault, and very low quiescent current in standby. The PG-SSOP-24-7 exposed-pad package provides excellent thermal dissipation and is qualified to Infineon's automotive reliability standards. Architecturally, the device pairs eight N-channel DMOS output stages with a digital control core that decodes SPI frames, drives fault flags, and arbitrates between direct-input and SPI commands. The embedded protective functions - over-current, open-load, over-temperature, and reverse battery - are designed to satisfy OEM body-controller module requirements, while the diagnostic word returned over SPI supports ISO 26262 functional-safety development at the system level. Typical applications include automotive body control modules driving relays and solenoids, junction box power distribution, lighting drivers (especially where PWM dimming is required), HVAC flap motors, and other inductive loads where protective switching and diagnostics are essential. The four input pins make it equally suitable as a stand-alone relay driver without MCU intervention during limp-home. When designing with this part, keep output flyback diodes or use relays with built-in freewheeling diodes because the low-side switch cannot clamp inductive kickback on its own. The exposed thermal pad must be soldered to a sufficient copper area on the PCB to keep junction temperature within ratings when driving multiple inductive loads simultaneously. Source: Infineon TLE7244SL product page and distributor datasheets, accessed 2026-09-14. This page combines verified distributor pricing, drop-in alternative analysis, and practical design notes that go beyond what the manufacturer datasheet alone offers, helping engineers select, source, and qualify the TLE7244SLXUMA2 more efficiently.
TLE75004EPDXUMA1 - 4-Ch Low-Side SPI Switch, 470mA | Infineon
The Infineon TLE75004EPDXUMA1 is a 4-channel low-side power switch with integrated N-channel MOSFETs, each capable of 470 mA continuous drain current, housed in a PG-TSDSO-14-41 exposed-pad package. The device integrates a 16-bit SPI interface for channel control and diagnostic readback, supports 3 V cranking capability for cold-start automotive conditions, and provides a fail-safe (Limp Home) mode that maintains critical outputs when the microcontroller or SPI link fails. A low-side switch is a power distribution topology in which the MOSFET is placed between the load and ground, allowing the load to be tied to a permanent supply rail (e.g., the vehicle battery). This architecture belongs to the broader category of smart power switches (SPS), which combine a power transistor, gate driver, protection circuitry, and a digital diagnostic interface in a single IC. Smart low-side switches have largely replaced discrete MOSFETs + fuses in body electronics because they provide per-channel current limiting, overload shutdown, open-load detection, and thermal protection without external sense resistors. Key features of the TLE75004EPDXUMA1 include per-channel current limiting, open-load detection in both on and off states, over-temperature shutdown with auto-restart, short-to-ground and short-to-battery protection, and reverse battery protection via an external resistor. The SPI interface operates at clock rates up to 5 MHz, allowing fast update of output states and rapid polling of fault registers. An IDLE pin enables the Limp Home mode where input pins directly drive the outputs without SPI intervention. Typical applications include automotive body control modules (BCMs), door modules, seat controllers, and LED lighting drivers where multiple low-current relays, solenoids, or LEDs must be switched under microcontroller supervision. The PG-TSDSO-14-41 package provides an exposed thermal pad that keeps junction temperature low even when all four channels are delivering full current simultaneously. When designing with this part, ensure the SPI lines are pulled up to VCC and the IDLE pin is tied high for normal SPI-controlled operation. The exposed pad must be soldered to a sufficiently large copper pour (at least 1 cm²) to achieve the datasheet thermal resistance. According to the manufacturer datasheet, the device is qualified to AEC-Q100 Grade 1, making it suitable for under-hood and other harsh automotive environments.
TLE75080ESDXUMA1 - 8-Ch SPI High-Side Switch, 330mA | Infineon
The Infineon TLE75080ESDXUMA1 is an 8-channel high-side power switch in a PG-TSDSO-24-21 (exposed pad) package, delivering 330 mA per channel for automotive and industrial relay and LED loads. Each channel integrates an N-channel MOSFET with active current limiting, and the device communicates over a 16-bit SPI interface for diagnostics and PWM control. A high-side switch (also called a smart power switch) is a semiconductor device that sits between a load and the positive supply rail. It replaces mechanical relays and discrete MOSFETs by combining a power transistor with protection, diagnostic, and communication circuitry. High-side switches sit in the family hierarchy: high-side switch -> power distribution switch -> power management IC -> semiconductor, and they enable centralized load control in body control modules, BCMs, and zonal architectures. Key features include 8 independently controlled channels, 16-bit SPI daisy-chain capability, integrated reverse-battery protection, open-load detection in on and off states, overtemperature shutdown with per-channel thermal sensors, and a Limp Home mode that allows safe operation at 3.0 V cranking transients. The device operates across a wide 4.5 V to 28 V supply range and withstands load-dump transients up to 40 V. The architecture uses N-channel MOSFETs with charge-pump-driven gates for true low-RDS(on) switching. Each channel includes current-limit set registers, individual fault flags, and PWM generation up to several hundred Hz. The exposed-pad package provides a thermal resistance below 30 C/W on standard 2 oz copper, supporting sustained 330 mA output per channel. Typical applications include automotive body electronics (lighting, HVAC blowers, seat control), industrial PLC relay drivers, and 24 V LED matrix modules. The combination of SPI diagnostics and cranking tolerance makes it well suited for 12 V automotive subsystems that must survive cold-crank events down to 3 V. When designing with this part, allocate PCB area for the exposed thermal pad and connect it to a solid copper pour. The Limp Home feature requires the SPI watchdog to be configured in the application firmware; an unconfigured watchdog defaults to fail-safe behavior. Per-channel current limit registers must be tuned to the load to avoid nuisance trips on inrush loads such as incandescent lamps or DC motors. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that supplement the manufacturer datasheet and accelerate your evaluation.
TLE75080ESHXUMA1 - 8-Ch SPI High-Side Switch 330mA | Infineon
The Infineon TLE75080ESHXUMA1 is an eight-channel high-side power switch in the PG-TSDSO-24-21 (TSDSO-24) package with 16-bit SPI control, integrated PWM generators, and Limp Home mode, designed for 12 V automotive and industrial loads. Each of the eight channels is rated at 330 mA continuous current and is built on Infineon's Smart Power SPIDER technology, integrating a vertical N-channel power MOSFET with charge pump, gate driver, current sense, and protective circuitry on a single die. The device operates from a nominal 12 V supply (with load-dump and jump-start tolerance typical of the TLE75080 family) and is qualified to AEC-Q100 for automotive body and chassis applications. Key features of this multichannel high-side switch include per-channel diagnostics (open load, short to battery, short to ground, overtemperature), parallel-input capability for direct MCU PWM control, a 16-bit SPI interface for configuration and status readback, and selectable latching or auto-restart fault behavior. The integrated charge pump drives the N-channel MOSFETs fully on at low battery voltage, achieving low R_DS(on) per channel. The Limp Home function allows a predefined safe output pattern if SPI communication is lost, critical for fail-operational body modules. Technically, the TLE75080-ESH belongs to the high-side switch category within the broader power distribution IC hierarchy: high-side switch -> smart power switch -> power management IC -> semiconductor. It is designed as an alternative to discrete MOSFET + fuse combinations, replacing many components with one SPI-controlled block. Each channel's integrated protection eliminates the need for external sense resistors, TVS clamps, and PTCs in many 12 V load drive circuits. Typical applications include automotive body control modules (BCM) driving lamps, LEDs, relays, and small motors; heating systems such as seat heaters and mirror heaters; industrial 24 V (rescaled) load switching; and energy/power distribution nodes in zonal E/E architectures. The PG-TSDSO-24-21 exposed-pad package enables direct PCB thermal dissipation without a heatsink at typical 12 V loads. When designing with this device, follow Infineon's PCB layout guidance for the exposed thermal pad, keep the SPI bus length short, and add a reverse-polarity protection diode at VBAT. Decouple VBAT and VS pins with a 100 nF ceramic plus a low-ESR electrolytic capacitor as recommended in the TLE75080-ESH datasheet. This page synthesizes distributor pricing, drop-in alternatives from the Infineon SPIDER family, and practical design notes for 12 V body-control applications that are not consolidated in the manufacturer datasheet.
TLE75602ESHXUMA1 - 8-Ch SPI Power Switch 330mA | Infineon
The Infineon TLE75602ESHXUMA1 is an 8-channel low-side and high-side SPI-controlled power switch housed in a PG-TSDSO-24-21 package, delivering up to 330 mA per channel for 12 V automotive and industrial loads. Built on Infineon's SPIDER (Smart Power Integration Device with Embedded Regulation) technology, the device integrates eight MOSFET output stages, a 16-bit SPI interface, configurable PWM generators per channel, and comprehensive diagnostic features in a single exposed-pad thermally enhanced surface-mount package. An SPI-controlled power switch (sometimes called a multi-channel high-side switch, low-side switch, or smart solid-state relay) is a power-management IC that replaces discrete MOSFETs, fuses, and relay driver circuitry with an integrated, microcontroller-addressable load driver. It sits hierarchically as a child of power distribution switches, which themselves are a sub-family of power management ICs. By consolidating eight independently controllable outputs behind a serial-peripheral-interface (SPI) command set, the TLE75602-ESH eliminates dozens of discrete components while providing per-channel fault reporting, current monitoring, and PWM dimming that discrete implementations cannot match. Key features include an operating voltage range that supports 3.0 V cranking transients (typical 4.5 V to 28 V with load-dump survivability above this range), per-channel Rds(on) in the sub-200 mΩ class, integrated reverse-battery protection via an external resistor, programmable overcurrent shutdown, open-load detection in both on and off states, and overtemperature pre-warning and shutdown. The 16-bit SPI runs at clock rates up to 5 MHz and allows parallel operation of multiple TLE75602 devices for systems requiring more than eight channels. Architecturally, each of the eight channels combines an N-channel MOSFET output stage with charge pump, gate driver, current-sense amplifier, and fault logic. The on-chip diagnostic block can flag short-to-battery, short-to-ground, open load, and overtemperature events back to the host microcontroller through dedicated SPI status registers, enabling ASIL-aware functional-safety implementations under ISO 26262. Typical applications include automotive body controllers driving lamps, LEDs, relays, and small motors; zone-ECU load switching; industrial 24 V PLC discrete I/O; HVAC blower control; and centralized power distribution modules. The device's AEC-Q100 qualification and 3.0 V cranking capability make it well suited for cold-start conditions. When designing with this part, place at least one 100 nF decoupling capacitor close to the VCC pin and follow the PCB layout recommendations in the Infineon datasheet to keep the exposed thermal pad soldered for low RthJA. Always configure unused channels in a defined OFF state via SPI to avoid floating-output diagnostic noise. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
TLE8082ESXUMA1 - Engine Management PMIC 5V SPI PG-TSDSO-24 | Infineon
The Infineon TLE8082ESXUMA1 is an Engine Management Power Management IC (PMIC) housed in a PG-TSDSO-24 (24-pin TSSOP with exposed pad) package. It integrates a 5 V supply output, four low-side drivers, and an SPI control interface for small-engine and motorcycle ECU applications. According to Infineon's product page, the device accepts a wide 6 V to 40 V input voltage range, making it suitable for 12 V and 24 V automotive battery systems. Engine management PMICs are highly integrated power and driver ICs that combine a microcontroller-compatible supply rail, multiple low-side switches, communication interfaces, and protection features in a single package. They sit at the top of the small-engine ECU power tree, replacing discrete regulators plus discrete MOSFETs and reducing BOM count, PCB area, and quiescent losses. The TLE8082ES family is positioned in Infineon's TLE808x small-engine PMIC lineup. Key features include integrated 5 V linear or switching supply, four low-side driver outputs for injector or relay control, SPI-configurable diagnostics, and built-in protection such as thermal shutdown, overcurrent limiting, and reverse-battery robustness. The PG-TSDSO-24 exposed pad provides a thermal resistance path that supports sustained operation of the integrated drivers at engine ambient temperatures up to the AEC-Q100 automotive qualification envelope. Architecturally, the TLE8082ESXUMA1 combines an internal bandgap reference, a pre-regulator, a 5 V post-regulator, four gate drivers for low-side N-channel MOSFETs, and an SPI slave for microcontroller communication. This integration lets a small 32-bit MCU control fuel injection, ignition, and sensor power without auxiliary driver ICs. Typical applications include small-engine ECUs for motorcycles, scooters, mopeds, marine outboards, generators, and handheld power equipment. The wide VIN range and integrated drivers are tailored to single-cylinder and small-displacement powertrains where PCB area and BOM cost dominate the design. When designing with this part, ensure the exposed pad is soldered to a sufficient copper pour for thermal relief; sustained low-side driver currents can dissipate significant power. Use the SPI watchdog to detect MCU lockup, and follow Infineon's small-engine reference design for injector flyback sizing. This page synthesizes distributor stock, parametric specifications, design considerations, and drop-in alternatives that supplement the manufacturer datasheet.
TLE9104SHXUMA1 - 4-Ch 3A SPI Low-Side Switch | Infineon
The Infineon TLE9104SHXUMA1 is a 4-channel low-side power switch with integrated N-channel MOSFETs, delivering 3 A continuous load current per channel, housed in a 20-pin PG-DSO-20-88 power package. It features a 16-bit Serial Peripheral Interface (SPI) for control, diagnosis, and configuration, plus comprehensive protection including over-current, over-temperature, over-voltage, and open-load detection. A multi-channel low-side driver IC is an integrated circuit that switches multiple resistive or inductive loads to ground using internal MOSFETs, controlled by a digital logic interface. Low-side drivers sit at the bottom of the load path (load connected to supply, switch to ground) and belong to the broader family of power distribution switches, motor/valve drivers, and powertrain switches used in automotive body and engine ECUs. Key features of the TLE9104SHXUMA1 include a 4.5 V to 28 V supply range, very low R_DS(on) per channel for high-efficiency switching, parallel-channel operation up to ~12 A, SPI-configurable dV/dt slew-rate control, and a 5 V VIO logic reference compatible with 3.3 V microcontrollers. The PG-DSO-20-88 exposed-pad package achieves a junction-to-ambient thermal resistance suitable for continuous 3 A per-channel operation with proper PCB copper area. The device is built on Infineon's SMART7 power technology with embedded protection state machine, providing deterministic fault handling required for ASIL-rated systems. The diagnostic block reports per-channel fault status, open-load, short-to-battery, and overtemperature flags through dedicated SPI registers. Typical applications include automotive engine-management loads (solenoid, valve, relay, injector drivers), transmission and gearbox control, body control modules, and 12 V / 24 V industrial switching. When designing, allocate at least 6 cm² of copper area to the exposed pad per channel of continuous current, and respect the SPI timing budget for sequential reads during fault scans. This page synthesizes distributor pricing, drop-in alternatives, and SPI configuration notes not collected in a single datasheet excerpt.
TLE9180D32QKXUMA1 - 6-Ch BLDC Gate Driver 90V LQFP-64 | Infineon
The Infineon TLE9180D32QKXUMA1 is a multi-channel gate driver IC for six N-channel MOSFETs designed for 12 V, 24 V and 48 V brushless DC motor control in automotive environments. Housed in a PG-LQFP-64-27 (LQFP-64 with exposed pad) package, the part uses a high-voltage Smart Power technology that lets bridge, motor and supply pins withstand up to 90 V, while motor pins tolerate negative transients typical of inductive switching. The IC integrates three half-bridge drivers plus a charge pump, current-sense amplifier, and SPI diagnostics, making it a near-complete solution for 3-phase BLDC motor control. A gate driver IC (also called a MOSFET driver or predriver) is a power-management building block that translates low-current logic-level control signals from an MCU into the high peak currents required to rapidly charge and discharge a power MOSFET gate. In the system hierarchy, gate drivers sit between the microcontroller and the power stage: MCU -> gate driver -> power MOSFETs -> motor. Compared with discrete bootstrap drivers, an integrated multi-channel gate driver such as the MOTIX TLE9180D-32QK dramatically reduces BOM count, improves timing skew between high-side and low-side channels, and centralizes protection functions. Key features of this part include support for battery voltages from 5.5 V to 72 V, programmable gate drive currents up to 1 A source/sink, integrated current-shunt amplifier with adjustable gain, and ASIL-C functional safety support per ISO 26262. The device targets safety-relevant applications and is qualified to AEC-Q100 for automotive use. Typical applications are automotive electric water pumps, oil pumps, e-bike and e-scooter traction drives, 48 V mild-hybrid auxiliary drives, BLDC fans and blowers for HVAC, and small industrial 3-phase pumps. The wide input range allows a single PCB design to support both 12 V passenger-vehicle platforms and 48 V commercial-vehicle or mild-hybrid systems, reducing platform SKU count for tier-1 suppliers.
TLF11251EPXUMA1 - 2.5A Half-Bridge Gate Driver | Infineon
The Infineon TLF11251EPXUMA1 is an integrated half-bridge gate driver capable of sourcing/sinking 2.5 A, designed for OPTIREG PMIC TLF35584/85 pairing with AURIX TC38x/TC39x 32-bit microcontrollers. Housed in a 14-pin PG-TSDSO-14-5 package, the device drives a PMOS/NMOS output stage with non-inverting logic and a wide 2.35 V to 7 V supply input. The combination of 60 ns typical propagation delay and 2.5 A peak drive makes it the companion driver for the core voltage rails of high-end 2nd-generation TriCore AURIX microcontrollers. A half-bridge gate driver is a power-management building block that combines a high-side and a low-side MOSFET driver in one IC, translating low-current PWM logic signals from a controller into the high-current gate drive required to switch power MOSFETs or, in this case, a PMOS/NMOS bridge. Within the broader IC taxonomy, this places the part in the gate-driver sub-family of power management ICs, itself a subset of PMIC and analog mixed-signal semiconductors. Half-bridge drivers are commonly used as core-supply pre-regulators or post-regulators next to multi-rail PMICs. Key features include 2.5 A peak gate-drive current, 60 ns propagation delay, non-inverting input logic, and 2.35 V to 7 V supply operation. The PG-TSDSO-14-5 thermally-enhanced small-outline package provides a low thermal resistance path for the high peak currents encountered during MOSFET switching transitions, while the non-inverting interface simplifies PWM routing from the host controller. Internally, the TLF11251EP combines a PMOS high-side path and an NMOS low-side path with adaptive drive strength and protection features. The 2.5 A capability allows it to switch large PMOS/NMOS bridges quickly, reducing switching losses and improving transient response on the AURIX core supply rail. The OPTIREG product family designation confirms Infineon qualification for safety-relevant automotive power architectures. Typical applications include AURIX TC38x/TC39x core supply pre-regulation, OPTIREG TLF35584/85 PMIC companion drivers, automotive 12 V ECU power trees, and industrial 24 V buck/boost pre-drivers. The wide supply range and high drive strength also make it suitable as a general-purpose PMOS/NMOS half-bridge in 5 V and 12 V distributed power systems. When designing with this device, observe the absolute maximum supply rating of 7 V and provide a local 100 nF + 1 µF decoupling network directly at the VCC pin. Keep the gate-drive traces short and width-matched to limit parasitic inductance, which can otherwise cause ringing on the PMOS/NMOS gate that may violate the AURIX core supply tolerance window.
TLF11251LDXUMA1 - 2.5A Half-Bridge Gate Driver for AURIX | Infineon
The Infineon TLF11251LDXUMA1 is a 2.5 A half-bridge gate driver IC housed in a 10-pin PG-TSON-10-2 (exposed pad) package, designed as a companion driver for the OPTIREG PMIC TLF35584/85 in automotive ECU power architectures. The part uses a PMOS/NMOS output stage that delivers 2.5 A peak source/sink current with 60 ns typical rise and fall times, enabling fast switching of power MOSFETs in 12 V automotive battery rails. A half-bridge gate driver is a power-management IC that translates low-current logic-level PWM signals from a microcontroller into the high-current gate-drive signals required to switch the high-side and low-side MOSFETs of a synchronous buck or boost converter. In the broader power-management hierarchy, the TLF11251 sits between the microcontroller (control layer) and the discrete power MOSFETs (switching layer), making it a critical glue device in DC-DC converter sub-systems. Without a dedicated driver, a microcontroller GPIO pin cannot directly charge and discharge a power MOSFET gate fast enough for efficient high-frequency switching. Key specifications include a 3.5 V to 7 V supply range, 2.5 A peak output drive, 60 ns propagation delay matching between high-side and low-side channels, and integrated shoot-through protection that prevents both MOSFETs from conducting simultaneously. The non-inverting input logic simplifies PWM signal routing, and the exposed thermal pad keeps junction temperature low during continuous switching. The driver is qualified to AEC-Q100 for automotive under-hood and chassis applications. The TLF11251 is specifically engineered to pair with Infineon's AURIX TC38x and TC39x 32-bit TriCore microcontrollers, providing the gate-drive stage for downstream buck converters that power the MCU core, ADC, and communication peripherals. The tight propagation-delay matching supports the dead-time control required by the OPTIREG TLF35584/85 PMIC family. Internal shoot-through protection and under-voltage lockout (UVLO) on the driver supply safeguard the power stage during cold-crank and load-dump transients typical of 12 V automotive electrical systems. Typical applications include 12 V automotive DC-DC converters, AURIX TC38x/TC39x ECU power stages, body-control modules, ADAS sensor power rails, and industrial 24 V buck regulators. The 2.5 A drive strength is sufficient for switching most sub-100 V N-channel MOSFETs commonly used in point-of-load converters up to approximately 10 A load. When designing with this part, place the bootstrap capacitor for the high-side channel as close as possible to the BST and SW pins to minimize switching losses. The exposed pad must be soldered to a sufficiently large copper pour to keep junction temperature within the -40 C to +125 C automotive grade-A operating range. This page synthesizes distributor pricing, parametric comparisons, and practical PCB-layout guidance not collected in a single Infineon document.
TPS1HB08BQPWPRQ1 - 40V 8mΩ Smart High-Side Switch | TI
The Texas Instruments TPS1HB08BQPWPRQ1 is a 40-V, 8-mΩ, single-channel smart high-side switch intended for 12-V automotive systems, delivered in a 16-pin HTSSOP (PWP) package with PowerPAD exposed thermal pad. It is qualified to AEC-Q100 grade 1 and integrates a low-Rdson N-channel MOSFET with on-resistance of 8 mΩ typical, supporting continuous load currents up to 70 A per the DigiKey listing, with an operating voltage range of 4 V to 18 V nominal and absolute maximum of 40 V. A high-side switch is a power-distribution topology that places the switching element between the supply rail and the load, allowing the load to be tied to chassis ground and providing inherent short-to-ground protection. Smart high-side switches extend this with on-die diagnostics and protection. In the system hierarchy, the TPS1HB08BQPWPRQ1 sits inside the power-management subsystem (load driver -> high-side switch -> power distribution IC -> automotive PMIC), enabling ECU designers to replace discrete MOSFETs, fuses, and sense resistors with a single AEC-Q100 qualified device. Key features include an adjustable current limit (6.4 A to 70 A depending on variant), integrated thermal shutdown, reverse-battery and load-dump protection, open-load detection in on and off states, short-to-ground and short-to-battery diagnostics, and a current-sense analog feedback output. The exposed thermal pad and 8 mΩ on-resistance minimize conduction loss and junction-temperature rise at heavy loads. The device operates across -40°C to +125°C ambient, satisfying under-hood automotive requirements. Architecturally, the TPS1HB08-Q1 combines a vertical N-channel power MOSFET with charge pump, gate driver, current-sense mirror, and an SPI-compatible or PWM-friendly control interface. The charge pump maintains gate enhancement at low VIN, while the analog CSN pin provides a ground-referenced current proportional to load current for closed-loop monitoring and fault detection. Typical applications include automotive body electronics such as headlight LED drivers, HVAC blower and fan control, seat and mirror actuators, infotainment power rails, and front-camera heater supplies. It is also used in zone-architect 12-V domain controllers where each high-current rail requires independent protection and diagnostics. When designing with this device, allocate sufficient PCB copper area to the PowerPAD to keep junction temperature below 150°C under worst-case VIN and ILOAD, and bypass VIN with at least 100 nF plus 10 µF ceramic placed within 5 mm of the pin. Use the CSN sense resistor value to set the analog current-limit threshold for your load. This page synthesizes distributor pricing, drop-in alternatives, and practical thermal/diagnostic notes that complement the manufacturer datasheet for AEC-Q100 design reviews.
TPS2001CDGKR - 2A USB Power Switch, 72mΩ, 5V VSSOP-8 | TI
The Texas Instruments TPS2001CDGKR is a single-channel, current-limited USB power-distribution switch housed in an 8-pin VSSOP (DGK) package. It delivers up to 2 A continuous load current from a 4.5 V to 5.5 V input rail, with a 72 mΩ (typical) N-channel MOSFET high-side switch that minimizes voltage drop and power dissipation in USB and other hot-plug applications. A power-distribution switch (also called a USB power switch or load switch) is a smart high-side MOSFET combined with protection circuitry. It sits between a system power rail and a downstream port, providing controlled turn-on, fault isolation, and current limiting. Within the broader taxonomy, a load switch sits beneath hot-swap controllers and above discrete MOSFETs in the power-management hierarchy, typically integrating an N-channel MOSFET, charge pump, current sense amplifier, and fault logic into one IC. Key features of the TPS2001CDGKR include a fixed 2 A current-limit threshold with ±20% accuracy, fast 2 µs short-circuit response, true reverse-current blocking when disabled, an output discharge resistor for safe USB VBUS decay, and an active-high enable input for power sequencing. The device asserts an active-low fault flag (OC) whenever the output exceeds the current-limit threshold or experiences a reverse-voltage condition, simplifying host monitoring in compliant USB ports. The device uses an internal charge pump to drive the gate of the N-channel MOSFET, achieving low Rds(on) without requiring an external bootstrap supply. Built-in thermal protection shuts down the switch when junction temperature rises excessively, and auto-restart resumes operation once the fault clears. The 8-VSSOP (DGK) footprint (3.0 mm body width) is compatible with industry-standard pinouts, allowing direct layout reuse across the TPS20xxC family. Typical applications include USB 2.0/3.0 downstream ports on motherboards and hubs, charging ports for tablets and smartphones, set-top boxes, and any 5 V rail requiring inrush and short-circuit protection. The combination of high current limit, low on-resistance, and true reverse blocking makes it a strong fit for hot-plug VBUS distribution where back-feeding from peripherals must be prevented. When designing with the TPS2001CDGKR, observe input-capacitor placement guidelines and ensure the trace between IN and GND pins is short and wide to handle inrush transients. Decoupling with a 1 µF ceramic between IN and GND is strongly recommended to keep the device stable during load steps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TPS2041BQDBVRQ1 - Automotive 0.5A USB Power Switch SOT-23-5 | TI
The Texas Instruments TPS2041BQDBVRQ1 is an automotive-qualified, single-channel, current-limited USB power-distribution switch housed in a 5-pin SOT-23 (DBV) package. It delivers a continuous load current of 500 mA from a 2.7 V to 5.5 V input rail, with an on-resistance of 105 mΩ (typical) and a factory-trimmed current limit of approximately 1 A. The TPS2041BQDBVRQ1 is the AEC-Q100 qualified variant of the TPS2041B, engineered for harsh automotive power-distribution environments. A USB power-distribution switch is a high-side load switch that sits between a 5 V bus and a downstream USB port or peripheral. It protects the host system from short circuits and over-current events by combining an N-channel MOSFET pass element with built-in current-limit, thermal shutdown, and undervoltage lockout. When the host asserts the active-low enable input, the switch closes to deliver current; when disabled, it presents a high-impedance path to block back-feeding. Key features include an accurate current limit at approximately 1 A, an integrated 105 mΩ N-channel MOSFET, thermal and short-circuit protection, an active-low logic enable input, and a flag output that asserts on fault. The SOT-23-5 footprint keeps board area minimal, making the part suitable for compact infotainment, telematics, and body-electronics modules where PCB real estate is constrained. The TPS2041BQDBVRQ1 uses an N-channel MOSFET pass element driven by an internal charge pump to achieve true low-RDS(on) high-side switching. This architecture minimizes I²R conduction loss on the 5 V rail and keeps thermal rise modest at the 500 mA continuous rating. The fixed current limit prevents the upstream automotive bus from sagging during load transients, while the thermal-shutdown circuit latches the switch off on excessive junction temperature. Typical applications include USB port power switching in automotive head units, body control modules, and rear-seat infotainment hubs. The device is also used to switch individual loads downstream of an LDO, providing fault isolation between branches. The wide input range (2.7 V to 5.5 V) tolerates cold-crank and load-dump conditions typical of 12 V automotive systems after regulation. When designing with this device, ensure the input supply is well-decoupled with at least 1 µF of ceramic capacitance placed close to IN. Avoid continuous operation above 500 mA and verify thermal performance against the SOT-23-5 θJA. This page synthesizes distributor pricing, drop-in alternatives, and design considerations not found in the manufacturer datasheet alone.
TPS2054 - Quad 0.5A USB Power Switch 80mOhm | Texas Instruments
The Texas Instruments TPS2054 is a quad-channel power-distribution switch integrating four N-channel MOSFET high-side switches in a single 16-pin SOIC package. Each channel supports 500 mA continuous current with a 0.9 A current limit, operating from a 2.7 V to 5.5 V input range with 80 mOhm maximum on-resistance (5 V input) and active-high enable inputs. A power-distribution switch is a type of load switch within the power management IC hierarchy that sits between a supply rail and its load, providing controlled turn-on, fault protection, and status reporting. USB power switches specifically guard downstream ports against overcurrent and short-circuit faults, preventing host rail collapse in systems that distribute 5 V power to multiple peripheral ports. Key features include 500 mA continuous current per channel for USB compliance, 135 mOhm typical high-side MOSFET resistance, short-circuit and thermal protection, and an overcurrent logic output (nFAULT) that signals fault conditions to the host controller. The device offers logic-level enable inputs, a 2.5 ms typical output rise time that limits inrush current during hot-plug events, and undervoltage lockout for predictable startup behavior. Internally, each switch uses a charge-pumped N-channel MOSFET gate drive with precision current-sense circuitry. When load current exceeds the 0.9 A limit, the device enters constant-current mode; sustained faults trigger thermal shutdown per channel. The open-drain overcurrent output allows direct connection to a microcontroller GPIO with a pull-up resistor. Typical applications include USB hub port power control, self-powered and bus-powered USB peripherals, multi-port charging accessories, hot-plug power switching in embedded systems, and industrial power-rail partitioning requiring per-channel fault isolation. Design tip: the controlled 2.5 ms rise time removes the need for external soft-start circuitry, but ensure PCB traces per channel are rated for 0.9 A fault current and place the input/output bypass capacitors close to the device pins for stable current-limit behavior.
TPS2054AD - Quad 500mA USB Power Distribution Switch | TI
The Texas Instruments TPS2054AD is a quad-channel current-limited power-distribution switch integrating four 80 mOhm N-channel MOSFET high-side switches, delivering 500 mA continuous current per channel (0.9 A minimum current limit) from a 2.7 V to 5.5 V input range in a 16-pin SOIC (D) package. A power-distribution switch, also called a high-side load switch or USB power switch, is a power management IC that sits between a supply rail and a load, turning the load on and off with a logic-level enable signal while protecting the upstream supply from faults. Within the power management hierarchy, it belongs to the power-distribution switch and load-driver class, complementing voltage regulators and hot-swap controllers in multi-port systems. Key features include independent enable inputs (CMOS- and TTL-compatible, active-high) for each channel pair, a per-channel current limit with independent thermal and short-circuit protection, and a shared fault-report logic output that flags overcurrent conditions to a host controller. A 2.5 ms typical output rise time limits inrush current when switching heavy capacitive loads, and undervoltage lockout keeps the outputs off until the input rail is valid. Architecturally, each N-channel MOSFET switch is driven by an internal charge-pump gate driver, which keeps on-resistance low at only 80 mOhm and minimizes voltage drop at full 500 mA load. Response to short circuits is fast, protecting the input rail from brownout during fault events. Typical applications include USB host and hub port power switching, hot-plug power distribution in set-top boxes and peripherals, and multi-rail power sequencing in industrial systems where heavy capacitive loads and short circuits are likely. A key design consideration: at 5.5 V input and full load on all four channels, estimate conduction loss as 4 x I^2 x RDS(on) = 4 x 0.25 x 0.08 = 80 mW (estimated), which the SOIC-16 package dissipates without a heatsink, but PCB copper around pins still aids thermal relief. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in same-brand alternatives (TPS2054BD, TPS2054DG4), and practical design notes for power-distribution switching designs.
TPS2062CDGNR - Dual 1A USB Power Switch | Texas Instruments
The Texas Instruments TPS2062CDGNR is a dual-channel, current-limited, power-distribution switch designed for USB and other hot-swap applications where heavy capacitive loads and short-circuits may be encountered. It integrates two 70-mΩ high-side N-channel MOSFET switches with independent enable inputs, providing a compact and robust power-switching solution in an 8-pin HVSSOP (DGK) package with exposed thermal pad. The device operates over an input voltage range of 2.7V to 5.5V and supports a continuous load current of 1A per channel, with a fixed current-limit threshold of 1.5A (typical) and an accurate ±20% current-limit tolerance. A power-distribution switch is a type of load switch that provides controlled power delivery to downstream circuits, offering protection against overcurrent, short-circuit, and over-temperature conditions. It sits between the power source and the load, acting as a smart switch that can be enabled or disabled via a control signal. In the system hierarchy, a power-distribution switch is a subset of power management ICs, which also include voltage regulators, DC-DC converters, and battery management devices. The TPS2062C family is specifically optimized for USB ports, where it ensures safe power delivery and protects the host controller from fault conditions. Key features of the TPS2062CDGNR include a fast overcurrent response time of 2 µs (typical), which quickly limits fault current to protect upstream components. The device also provides reverse current blocking, output discharge function, soft-start to reduce inrush current, and under-voltage lockout (UVLO) to ensure proper operation during power-up. Built-in over-temperature protection and short-circuit protection further enhance system reliability. The active-low enable inputs allow for simple logic control, and the 70-mΩ on-resistance minimizes power loss and voltage drop across the switch. Technically, the TPS2062CDGNR uses a constant-current limiting scheme that maintains a safe output current during overload conditions, preventing damage to the switch and the load. The output discharge function actively pulls the output to ground when the switch is disabled, ensuring no residual voltage remains on the load. The soft-start feature limits inrush current when driving capacitive loads, which is critical for USB applications where downstream capacitors can be large. The device is specified for operation over the industrial temperature range of -40°C to +125°C, making it suitable for a wide range of environments. Typical applications include USB ports on computers, hubs, and peripherals, as well as general-purpose power switching in consumer electronics, industrial equipment, and set-top boxes. The dual-channel configuration allows two independent loads to be controlled from a single device, saving board space and cost. The TPS2062CDGNR is also ideal for powering downstream devices in systems that require hot-swap capability, such as docking stations and battery chargers. When designing with this device, ensure that the input and output capacitors are placed close to the pins to minimize parasitic inductance and maintain stable operation. The exposed thermal pad should be soldered to a large copper area on the PCB to enhance heat dissipation, especially when operating at high currents. Additionally, the enable pins should be driven with proper logic levels to avoid unintended switching.
TPS2062DR - Dual 1A USB Power Switch | Texas Instruments
The Texas Instruments TPS2062DR is a dual-channel, current-limited power distribution switch designed for USB and general-purpose power management applications. It integrates two 70-mΩ high-side N-channel MOSFETs, each capable of delivering up to 1 A continuous current, with an input voltage range of 2.7 V to 5.5 V. The device is housed in an 8-pin SOIC (D) package and features an active-low enable input, making it suitable for power sequencing and hot-swap applications. A power distribution switch is a semiconductor device that controls and protects power delivery to downstream loads. It typically includes a high-side MOSFET, current sensing, and protection features such as overcurrent, thermal shutdown, and undervoltage lockout. In a system hierarchy, the TPS2062DR sits between the main power rail and peripheral devices, acting as a smart switch that can be turned on/off via a logic signal while providing fault protection. Key features of the TPS2062DR include a 70-mΩ high-side MOSFET, 1-A continuous current per channel, accurate current limit (1.1 A min, 2.1 A max), thermal and short-circuit protection, undervoltage lockout, deglitched fault report (OC), and a typical rise time of 0.6 ms. The active-low enable input allows for straightforward control from microcontrollers or logic gates. The device operates over a junction temperature range of -40°C to 125°C, making it suitable for industrial and automotive environments. Technically, the TPS2062DR uses a current-limited architecture that ensures safe operation under overload conditions. The accurate current limit prevents excessive current draw, protecting both the switch and the load. The deglitched fault report (OC) provides a clean signal to the host controller, avoiding false triggers from transient currents. The undervoltage lockout ensures the switch remains off until the input voltage is stable, preventing erratic behavior during power-up. Typical applications include USB port power switching, hot-swap power distribution, and power management in consumer electronics, industrial equipment, and networking devices. The dual-channel configuration allows independent control of two loads, making it ideal for applications requiring multiple power domains. When designing with the TPS2062DR, ensure adequate input and output capacitance to maintain stability and minimize voltage transients. Place the device close to the load to reduce parasitic inductance and improve fault response. The active-low enable pin should be pulled up or driven by a logic signal; do not leave it floating.
TPS2115APW - 1.25A, 5.5V Power Mux w/ Status | Texas Instruments
The Texas Instruments TPS2115APW is a 2.8-V to 5.5-V, 84-mΩ, 1.25-A autoswitching power multiplexer (power mux) housed in an 8-pin TSSOP (PW) package. It accepts two input supplies (IN1 and IN2) and delivers a regulated output to a common load with sub-ohm (84 mΩ typical) N-channel MOSFET pass elements per channel. The device features manual and automatic switchover modes, a STATUS output flag, and cross-conduction blocking logic to prevent momentary shorting between the two sources during transitions. A power mux is a category of power-management IC that arbitrates between two or more DC input sources (battery, wall adapter, USB, auxiliary rail) and routes one of them to the load. Within the broader taxonomy, power muxes sit below load switches and above simple ideal-diode OR-ing controllers, combining the low-loss benefits of MOSFET pass elements with intelligent source-selection logic. The TPS2115A family specifically targets systems requiring seamless transitions between a primary and backup supply without brown-outs on the load. Key features of the TPS2115APW include 84 mΩ typical on-resistance per channel, low 0.5 µA standby current, programmable current limiting, inrush current control, thermal shutdown protection, and a wide 2.8 V to 5.5 V operating range on both input rails. The integrated STATUS pin reflects which source is currently active, enabling host-side telemetry in multi-rail systems. Architecturally, the TPS2115APW uses back-to-back N-channel MOSFETs per channel driven by charge-pumped gate drivers. The body-diode reverse-blocking design prevents unintended current flow from a higher-voltage rail into a lower-voltage rail. The control logic implements break-before-make switching with user-programmable switchover thresholds and switching speed. Typical applications include battery-backed-up portable electronics, USB/wall-adapter power switching in handheld terminals, multi-rail industrial sensor nodes, redundancy power OR-ing in 5V systems, and any application requiring glitch-free transitions between two DC sources. When designing with the TPS2115APW, consider that the TSSOP-8 package has a thermal resistance of approximately 150 °C/W; continuous 1.25 A operation at high VIN requires adequate copper pour. The MS pin (mode select) and ILIM pin (current limit) require external component selection to balance inrush vs steady-state behavior. Cross-conduction blocking eliminates the need for external back-to-back FETs, simplifying BOM. This page synthesizes distributor pricing, drop-in alternatives within the TSSOP-8 footprint, and design guidance not found in the manufacturer datasheet alone - giving procurement and design engineers a one-stop reference for source-selection decisions.
TPS2121RUX - 22V 4.5A Priority Power MUX | Texas Instruments
The Texas Instruments TPS2121RUX is a 2.7-V to 22-V, 56-mΩ, 4.5-A priority power multiplexer (power MUX) with seamless switchover, housed in a 12-pin VQFN-HR (RUX) package measuring 2.0 mm × 2.5 mm. It manages two input power sources (IN1 and IN2) and selects one to power a single output (OUT) according to a user-defined priority scheme. The device supports up to 4.5 A continuous load current with an internal 56-mΩ (typical) Rds(on) MOSFET per channel, with adjustable current limit set by an external resistor. A power multiplexer is a load-sharing/redundancy switch that allows a system to draw power from one of two sources with priority logic, automatic switchover, and in-rush control. The TPS2121 belongs to the ORing controller / power MUX / load-switch product hierarchy, sitting between discrete MOSFET ORing designs (anode-to-cathode diodes or ideal-diode controllers) and full PMIC solutions. It integrates dual back-to-back N-channel MOSFETs, priority arbitration, adjustable current limit, soft-start, and seamless fast switchover (< 5 µs) inside a tiny QFN footprint, eliminating dozens of discrete components. Key features include 2.7-V to 22-V operating input range, 56-mΩ per-channel Rds(on), 4.5-A continuous current capability, adjustable current limit (ILIM), seamless switchover within 5 µs, and a logic-controlled priority mode (PR1 = High → IN1 priority; PR1 = Low → IN2 priority). The VQFN-HR-12 (RUX) package has an exposed thermal pad (PowerPAD) for low thermal resistance, supporting up to ~2 W continuous dissipation on a modest PCB copper pour. The device operates over -40 °C to +125 °C junction temperature and is characterized for industrial-grade environments. The architecture uses TI's priority-based power-path control: the device continuously compares IN1 and IN2 voltages against an internal reference (2.5 V typical on PR1) and switches to the higher-priority source when it is valid. During switchover, internal break-before-make control prevents cross-conduction; the output is held up by output capacitance during the brief (~5 µs) transition. The current-limit and soft-start blocks protect against in-rush spikes when a freshly-selected source is brought online. Typical applications include redundant power rails in industrial PLCs and factory automation, backup battery switching in portable medical and IoT devices, USB-C PD source multiplexing, multi-battery Point-of-Sale (POS) terminals, and automatic transfer of AC adapters versus battery in notebook docking stations. The compact 2 mm × 2.5 mm footprint makes it ideal for space-constrained designs that previously required a discrete ORing controller plus two MOSFETs. When designing with the TPS2121, place input and output ceramic capacitors as close as possible to the IC pins (10 µF minimum on IN1, IN2, and OUT recommended) to minimize voltage droop during switchover. Use the PR1 resistor divider to set the VIN1 priority threshold, set ILIM with an external resistor (RILIM = K / ILIM), and provide adequate copper area on the PowerPAD for thermal dissipation. Avoid parallel connection of multiple TPS2121 units - one device per system is standard. This page synthesizes distributor pricing, drop-in alternatives, prioritized selection guidance, and practical PCB layout notes that go beyond a typical manufacturer datasheet summary.
TPS22919-Q1 - 5.5V 1.5A Load Switch SC-70-6 | Texas Instruments
The Texas Instruments TPS22919-Q1 is a self-protected, single-channel load switch with controlled slew rate that integrates an N-channel MOSFET operating from 1.6 V to 5.5 V input, supporting up to 1.5 A of continuous current in a 6-pin SC-70 (DCK) package. The device offers a 90 mOhm typical on-resistance and AEC-Q100 Grade 1 automotive qualification. A load switch is a power management IC that acts as an electronic switch between a power rail and its load, enabling or disabling power delivery under logic control. Load switches sit within the power distribution and protection hierarchy of a system, complementing voltage regulators, e-fuses, and hot-swap controllers. They are used to sequence rails, reduce leakage in standby, and isolate faults downstream. Key differentiating features of the TPS22919-Q1 include controlled output slew rate for inrush-current limiting during turn-on, adjustable quick output discharge (QOD) that pulls the output low when the switch is off, and integrated self-protection including short-circuit current limiting. According to TI, the device is qualified for automotive applications under AEC-Q100 device temperature grade 1. The internal N-channel MOSFET pass element gives a low, well-controlled on-resistance of 90 mOhm, which limits voltage drop: at 1 A the drop is roughly 90 mV, dissipating about 90 mW. The controlled slew rate soft-starts capacitive loads, avoiding the large inrush spikes that can sag upstream rails or trip protection circuits. The QOD function is adjustable via an external resistor, letting designers trade discharge speed against pull-down current. Typical applications include automotive camera and sensor modules, infotainment power distribution, peripheral-rail switching in ADAS domains, and portable or industrial designs needing fault-isolated power gating. The wide 1.6 V to 5.5 V input range covers 1.8 V, 3.3 V, and 5 V rails in one footprint. For design, account for the Rds(on) power loss at high current, ensure the ON-pin logic threshold matches the controlling GPIO, and size the QOD resistor for the required discharge time. Do not rely on the switch to regulate voltage - it only gates the rail. This page synthesizes distributor availability data, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet.