بەرهەمەکان (310+)

LBAA0QB1SJ-296 - LoRaWAN Sub-GHz Module 868/915MHz | Murata
LBAA0QB1SJ-296

LBAA0QB1SJ-296 - LoRaWAN Sub-GHz Module 868/915MHz | Murata

The Murata Electronics LBAA0QB1SJ-296 (Type 1SJ) is a compact LoRaWAN transceiver module operating in the 868 MHz and 915 MHz sub-GHz ISM bands from a 2 V to 3.6 V supply, delivering up to 21.5 dBm output power and -137 dBm receiver sensitivity in a surface-mount package. A LoRaWAN module is a complete long-range, low-power wireless radio subsystem that integrates a sub-GHz RF transceiver, antenna matching network, and modem firmware on a single certified land-pattern device. Within the LPWA (Low Power Wide Area) connectivity hierarchy, it sits above bare RF chips and below complete end-node systems, letting engineers add km-range telemetry to sensors, meters, and trackers without designing an RF section or navigating radio-equipment certification from scratch. Key features include one of the smallest footprints in the industry for a LoRaWAN module, lower power consumption and higher RF output than previous Murata generations, radio law certification already obtained for major regions, and preloaded modem software for the US915 band that is controlled entirely through simple AT commands. Receiver current is typically 15.5 mA to 20 mA, making the module suitable for coin-cell and battery-powered nodes. At its core the module is built on the Semtech SX1262 LoRa chipset, which provides the LoRa spread-spectrum modulation, high link budget, and up to +21.5 dBm transmit power. Murata integrates the RF front end, crystal reference, and matching network, then validates the design against regional radio regulations so customers inherit a certified RF chain. Typical applications include smart utility metering on US915 LoRaWAN networks, battery-powered asset tracking, smart agriculture sensor nodes, and industrial IoT gateways-to-node links where multi-kilometer range and multi-year battery life are required. For design success, allocate a ground plane under the module, follow the Murata recommended land pattern, and account for the 2 V to 3.6 V supply window - a regulated 3.3 V rail is the natural choice. Antenna is not included on the -296 variant, so plan RF feed and antenna matching on the host PCB. This page synthesizes distributor pricing, firmware-variant comparison (-295 vs -296), and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
LBAD0XX1SC-NTN - LTE Cat M1/NB-IoT NTN Module | Murata
LBAD0XX1SC-NTN

LBAD0XX1SC-NTN - LTE Cat M1/NB-IoT NTN Module | Murata

The Murata LBAD0XX1SC-NTN (Type 1SC-NTN) is a Cat M1/NB-IoT LPWA cellular module with integrated Rel-17 Non-Terrestrial Network (NTN) satellite communication support, GNSS positioning, and integrated SIM, housed in an 11.1 x 11.4 x 1.5 mm silver resin-shielded surface-mount package. An LPWA (Low Power Wide Area) cellular module is a wireless communication subsystem that connects IoT devices to LTE Category M1 (LTE-M) and NB-IoT networks optimized for low data rates, deep coverage, and multi-year battery life. Within the system hierarchy, an LPWA module sits between the host MCU and the cellular antenna, handling RF transceiving, protocol stack execution, and network registration so the host processor only sees an AT command or OpenMCU interface. Key features of the Type 1SC-NTN include the world's smallest Cat. M1/NB-IoT footprint with global certification, seamless Rel-17 NTN satellite connectivity via Skylo technology that requires no hardware design changes, support for GPS/GNSS positioning, an Integrated SIM (iSIM) option, and Murata's OpenMCU capability that lets the module host application code directly. The module operates in the LTE low band (699 MHz to 915 MHz) and mid band (1.71 GHz to 2.025 GHz) and is optimized for 3GPP class 3 output power of +23 dBm. Architecturally, the module comprises an Altair ALT1250 transceiver paired with an FEM (front-end module) and external flash memory, all integrated behind Murata's silver resin shield. This single-package integration minimizes external BOM count, simplifies RF layout, and reduces time-to-market for IoT device makers. Regulatory certifications include FCC/IC, ETSI, and TELEC, plus PTCRB and GCF operator certifications, enabling worldwide deployment on a single design. Typical applications include asset tracking that roams beyond terrestrial coverage, smart utility metering, agricultural and maritime sensors, and fleet telematics where uninterrupted communication - anytime, anywhere - is a requirement. The NTN capability is especially valuable where terrestrial LTE-M/NB-IoT coverage is unavailable or unreliable. When designing with this module, follow Murata's recommended land pattern exactly; datasheet guidance notes that characteristics can vary with land dimensions, NC-terminal grounding method, and PCB material and thickness. Antenna is not included, so plan an external antenna with a 50-ohm matched feed. This page synthesizes distributor availability data, NTN capability details, and practical design guidance not consolidated in the manufacturer datasheet, along with drop-in family alternatives and application pairing recommendations.

RFQ پەیوەندی
LBAD0XX1SC-SFS - LTE Cat M1/NB-IoT Module | Murata
LBAD0XX1SC-SFS

LBAD0XX1SC-SFS - LTE Cat M1/NB-IoT Module | Murata

The Murata LBAD0XX1SC-SFS (Type 1SC-SFS) is an LTE Cat M1 / NB-IoT cellular LPWA transceiver module with +23 dBm Class 3 LTE output power, integrated GNSS positioning support, and a compact 11.1 x 11.4 x 1.5 mm (max) silver resin shielded package with LGA-style surface-mount lands. An LPWA (Low Power Wide Area) module is a type of cellular connectivity subsystem that sits within the wireless module hierarchy: transceiver module -> cellular IoT module -> RF & wireless component. LPWA technologies such as LTE-M (Cat M1) and NB-IoT trade peak throughput for dramatically lower power consumption and superior deep-indoor penetration, making them the dominant connectivity choice for battery-powered IoT devices that must communicate over licensed cellular spectrum for 10 or more years on a single battery. Key features of the LBAD0XX1SC-SFS include dual-mode LTE Cat M1 and NB-IoT operation, a user-friendly AT command interface for seamless host integration, and ultra-low-power eDRX and PSM sleep modes that enable 10+ year battery life as stated by Murata. The module integrates the Altair ALT1250 transceiver together with a FEM (front-end module) and external flash memory, so the host board needs only an antenna and minimal external circuitry. On the technical side, the module uses an integrated TCXO (temperature-compensated crystal oscillator) with robust low-drift thermal characteristics, which removes the need for an external oscillator and preserves RF accuracy across the full industrial temperature range. RF coverage spans low and mid LTE bands (699 MHz to 915 MHz and 1.71 GHz to 2.025 GHz per DigiKey listings), and the module is optimized for 3GPP release-compliant Class 3 +23 dBm output power. Murata also highlights support for GPS/GNSS, OpenMCU, Integrated SIM, and NTN (non-terrestrial network) operation in the Type 1SC family. Typical applications include battery-powered smart utility meters, asset trackers, smart-city sensors, and industrial telemetry endpoints where multi-year battery life and global cellular certification (FCC/IC, ETSI, TELEC, PTCRB, GCF) shorten time to market. Design consideration: place the module antenna feed with a controlled 50-ohm trace and follow Murata's recommended land pattern exactly, since the shielded LGA construction relies on the PCB ground plane for RF and thermal performance. This page synthesizes verified manufacturer and distributor data, pricing structure, drop-in family variants, and practical design notes not found in the datasheet alone. Pricing shown reflects availability as of 2026-10-19.

RFQ پەیوەندی
LBAD0XX1WG-EVK-TEMP - LTE Cat M1 Evaluation Kit | Murata
LBAD0XX1WG-EVK-TEMP

LBAD0XX1WG-EVK-TEMP - LTE Cat M1 Evaluation Kit | Murata

The Murata LBAD0XX1WG-EVK-TEMP is a temperature-qualified evaluation kit for the Type 1WG (LBAD0XX1WG) LTE Cat M1 cellular LPWA module, designed to accelerate development of battery-powered IoT devices that connect over LTE-M networks. The underlying module operates from a 2.85 V to 4.35 V supply, supports receive levels down to -23 dBm, and uses an external antenna configuration, all packaged in a compact LGA-format shielded construction. An LTE Cat M1 module is a cellular LPWA (Low Power Wide Area) modem that implements 3GPP LTE-M protocols, sitting within the broader hierarchy of cellular connectivity: cellular modem -> LTE LPWA module -> wireless connectivity module -> IoT communication device. LTE Cat M1 is optimized for machine-type traffic where ultra-low power, deep coverage, and 10+ year battery life matter more than throughput, distinguishing it from Cat NB1/NB-IoT (narrowband, reduced mobility) and standard LTE (high throughput, high power). Key features evidenced across the Type 1WG/1SC family include 3GPP eDRX and PSM power-saving modes, hibernation power of just 3 uA, eDRX power below 45 uA at 8 hyperframes, and a configurable dormant window in PSM mode. These modes collectively enable the quoted battery life of up to 10+ years for small battery-operated IoT devices. The module family also supports over-the-air (OTA) firmware update, eliminating field-recall costs during deployment. The Type 1SC sibling measures just 11.1 x 11.4 x 1.5 mm and integrates an Altair ALT1250 transceiver, FEM, external flash, and a low-drift integrated TCXO in a silver resin shielded package, indicating the integration density of this product line. Typical applications for this evaluation platform include smart utility meters, asset trackers, smart-city sensors, and industrial telemetry nodes - anywhere a small, battery-operated device must maintain multi-year cellular connectivity. Engineers use the EVK to validate RF performance, characterize current consumption across PSM/eDRX states, and prototype network registration and OTA update flows before committing to custom PCB layouts. When designing with the Type 1WG module, pay close attention to supply-voltage sequencing and current-profile headroom: even though average current is microamps, transmit bursts require the 2.85 V to 4.35 V supply rail to remain stable under pulsed load, so input capacitance and battery internal resistance must be characterized. This page synthesizes verified manufacturer product data, distributor listings, and practical evaluation guidance for the LBAD0XX1WG-EVK-TEMP that is not consolidated on the manufacturer datasheet alone.

RFQ پەیوەندی
LBAD0ZZ2GD-EVK - LTE-M/NB-IoT Cat.M1 Eval Kit | Murata
LBAD0ZZ2GD-EVK

LBAD0ZZ2GD-EVK - LTE-M/NB-IoT Cat.M1 Eval Kit | Murata

The Murata LBAD0ZZ2GD-EVK is an evaluation kit for the Type 2GD (LBAD0ZZ2GD) LTE Cat.M1/NB2 cellular IoT module, an ultra-small, ultra-low-power LPWA module that integrates the LTE SoC, RF front end, crystal, and SRAM and flash memory in a compact LGA package. The kit enables engineers to prototype, test, and certify 3GPP Rel-14 LTE-M and NB-IoT connectivity before committing to a custom PCB design. An LPWA (Low Power Wide Area) module is a type of cellular communication module belonging to the broader hierarchy of connectivity module -> RF module -> IoT communication device. LTE Cat.M1 (LTE-M) and NB-IoT are licensed-band 3GPP standards designed for battery-powered IoT devices that prioritize minimal cost and power consumption over throughput; LTE-M provides approximately 1 Mbps upstream and 1 Mbps downstream, and both standards support mobility, making them suitable for moving devices with reduced radio interference compared with unlicensed-band solutions. Key features of the underlying LBAD0ZZ2GD module include 3GPP Rel-14 compliance, dual-mode LTE-M/NB2 operation, 8 MByte of flash memory, and low-power modes including PSM (Power Saving Mode) and eDRX (extended Discontinuous Reception). Murata states its compact LPWA module family achieves power consumption as low as 1.5 uA in Power Saving Mode, which is a central reason for selecting this platform for battery-powered designs. The module uses an external antenna configuration and an LGA surface-mount land pattern per Murata standard recommendations. Technically, the Type 2GD integrates the complete signal chain on a single substrate: the LTE SoC handles baseband and protocol processing, the RF front end drives the external antenna, and integrated SRAM and flash eliminate external memory BOM items. Because the RF front end, crystal, and memory are pre-integrated and pre-tested, designers avoid the most difficult RF layout tasks and inherit Murata's certification baseline, with the module carrying FCC ID HSW-TY2GD via Murata Electronics North America. Typical applications evaluated with this kit include smart utility metering, asset tracking, smart city infrastructure, industrial sensors, and battery-powered telemetry nodes. The evaluation kit lets developers exercise PSM/eDRX duty cycles and measure real current profiles before finalizing the power budget. A key design consideration: Murata's datasheet notes that module characteristics vary depending on land pattern drawing method, grounding method, land dimensions, NC-terminal land forming, and PCB material and thickness, so the EVK-provided reference layout should be followed closely when transitioning to production. This page synthesizes distributor data, verified web sources, and practical integration guidance for the LBAD0ZZ2GD-EVK not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
LBEE5HY1MW-230 - Wi-Fi 5 + BT 5.0 Module, Type 1MW | Murata
LBEE5HY1MW-230

LBEE5HY1MW-230 - Wi-Fi 5 + BT 5.0 Module, Type 1MW | Murata

The Murata LBEE5HY1MW-230 is a Type 1MW surface-mount wireless combo module integrating Wi-Fi 802.11a/b/g/n/ac (Wi-Fi 5) dual-band 2.4 GHz/5 GHz connectivity with Bluetooth 5.0 BR/EDR/LE on a single shielded PCB, based on the Infineon CYW43455 chipset. Per the manufacturer datasheet, the module delivers up to 433 Mbps PHY on Wi-Fi and 3 Mbps PHY on Bluetooth, with an integrated dual-band RF chain, crystal, power-management circuitry, and shielding in a compact SMD footprint suitable for space-constrained IoT and embedded designs. A Wi-Fi + Bluetooth combo module is a pre-certified subsystem that bundles the radio transceiver, baseband processor, antenna matching network, and regulatory shielding into a single reflow-solderable component. The module sits between the host application processor (which runs the network stack and BT profiles) and the wireless air interface, offloading RF complexity, FCC/ETSI/TELEC certification burden, and BOM risk. The Murata Type 1MW family specifically targets low-power IoT endpoints that need modern dual-band Wi-Fi and Bluetooth 5.0 coexistence without discrete RF design effort. Key features of the LBEE5HY1MW-230 include dual-band 2.4 GHz and 5 GHz operation with 802.11ac wave-2 (433 Mbps), Bluetooth 5.0 with LE 2M PHY and LE Coded PHY support, integrated shield and reference clock, and an SDIO 3.0 + UART host interface. The SMD package is reflow-compatible at standard 260 °C peak profile, and antenna is not included (typical for modules with host-board antenna or external antenna pigtail). Operating temperature is rated for industrial -30 °C to +85 °C environments. Architecturally, the module integrates the Infineon CYW43455 die, a 37.4 MHz reference crystal, RF matching network, transmit balun, low-noise PA chain, and DC-DC regulators on a multilayer ceramic substrate with metal shield. Wi-Fi and Bluetooth radios share an antenna diversity topology with internal coexistence arbitration, allowing simultaneous 2.4 GHz WLAN + BT operation with on-chip packet scheduling. The module presents a standard SDIO 3.0 interface to the host MCU/MPU for WLAN and a 4-wire UART (plus PCM for BT audio) for Bluetooth. Typical applications include Wi-Fi 5 + BLE smart-home gateways, industrial IoT gateways, wireless POS terminals, audio streaming products (BT classic A2DP + Wi-Fi), medical telemetry devices, and consumer electronics that need modern dual-band connectivity without in-house RF expertise. The integrated shield dramatically simplifies EMC compliance at the end-product level. When designing with the LBEE5HY1MW-230, allocate a keep-out zone under the antenna feed, provide a clean 3.3 V rail with adequate bulk decoupling, and follow Murata's reference layout for the host-board antenna or pigtail. Host-driver selection (Linux/Backport, Android HAL, or vendor-specific MCU port) is critical - confirm firmware compatibility before committing to the design. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
LBES0ZZ2FR-580 - Wi-Fi 6 + BT 5.4 + 802.15.4 Module | Murata
LBES0ZZ2FR-580

LBES0ZZ2FR-580 - Wi-Fi 6 + BT 5.4 + 802.15.4 Module | Murata

The Murata LBES0ZZ2FR-580 is a Type 2FR multi-radio SMD transceiver module based on the NXP RW612 combo chipset, supporting IEEE 802.11a/b/g/n/ac/ax (Wi-Fi 6) dual-band, Bluetooth LE 5.4, IEEE 802.15.4 (Thread/Zigbee), and Matter smart-home connectivity in a single, highly integrated 140-pin surface-mount package. A Wi-Fi + Bluetooth module is a pre-certified radio subsystem that combines an RF transceiver, baseband processor, and integrated antenna or RF trace on a single PCB. These modules dramatically reduce BOM count, FCC/CE/TELEC certification cost, and PCB complexity by abstracting the radio hardware and presenting a host MCU interface. The Type 2FR sits in the module product hierarchy between simple Wi-Fi-only modules and full SoC platforms, and is widely adopted in connected smart devices, enterprise and industrial automation, smart accessories, and smart-energy endpoints. Dual-band 2.4 GHz and 5 GHz operation plus 802.15.4 makes it a true multiprotocol gateway IC for Matter, Thread, and Zigbee ecosystems. Key features include dual-band 2.4 GHz and 5 GHz Wi-Fi 6 (802.11ax) operation, Bluetooth LE 5.4 with long-range and direction-finding support, integrated 802.15.4 radio for Thread and Zigbee, an integrated high-performance Arm Cortex-M33 application MCU with advanced security (secure boot, crypto accelerators, TrustZone-M), a supply voltage range of 3.14 V to 3.46 V (typical 3.3 V), output power from 12 to 18 dBm, and receive sensitivity down to -104.7 dBm depending on modulation. The surface-mount LGA-style module ships tape-and-reel and is lead-free. The RW612 silicon inside combines a Wi-Fi 6 MAC/PHY, Bluetooth 5.4 LE radio, and 802.15.4 PHY on a single die with an internal PA, LNA, and RF front-end. Murata integrates the chipset, crystal, RF matching, and shielding into a module that is pre-certified for major regulatory domains, eliminating the customer's RF design risk and antenna tuning effort. The on-die Cortex-M33 host allows bare-metal or RTOS firmware to run directly on the module, removing the need for an external host MCU for many IoT edge applications. Typical applications include Matter-compatible smart-home hubs, Thread border routers, Wi-Fi/BLE smart appliances, industrial IoT gateways, asset-tracking sensors, and connected lighting controllers. The dual-band Wi-Fi 6 capability is particularly valuable in congested environments where 2.4 GHz-only devices suffer interference from neighboring Wi-Fi networks, microwaves, and Bluetooth peripherals. When designing with this module, follow Murata's reference layout and grounding recommendations exactly. The RF trace routing, decoupling placement, and host-interface pin mapping are pre-engineered; deviating from the reference design will degrade RF performance and may void regulatory certifications. Use the recommended host-driver SDK from NXP/Murata to leverage the integrated MCU and radio coexistence features.

RFQ پەیوەندی
LBEU5ZZ1WL-633EVB - LoRaWAN GNSS BLE Wi-Fi Eval Board | Murata
LBEU5ZZ1WL-633EVB

LBEU5ZZ1WL-633EVB - LoRaWAN GNSS BLE Wi-Fi Eval Board | Murata

The Murata LBEU5ZZ1WL-633EVB is an evaluation board for the Type 1WL (LBEU5ZZ1WL-633) multi-technology fused LoRaWAN geolocation module, which combines Semtech LR1110 LoRa/Wi-Fi/GNSS scanning, a STMicroelectronics STM32WB55VGY6 wireless MCU, and an Airoha MT3333AV high-performance GNSS receiver in one platform for developing low-cost IoT tracking devices. An LPWAN geolocation module is a type of wireless connectivity module that fuses long-range low-power radio (LoRaWAN) with multiple positioning technologies (satellite GNSS, Wi-Fi access-point scanning, and GNSS scanning). Within the system hierarchy, it sits above individual transceivers and below complete end products, providing a pre-certified radio subsystem for asset tracking, telemetry, and industrial IoT nodes. Key features include ultra-low power design: the internal MCU draws only 4.7 uA typical in stop2 mode with RTC running while the LR1110 and MT3333 are off, per the Type 1WL datasheet (Rev. D, VDD = 3.3 V, 25 C). Wireless coverage spans LoRa sub-GHz, Wi-Fi 802.11b/g/n at 2.4 GHz, Bluetooth v5.2, and GNSS including GPS and BeiDou. The STM32WB55 provides an ARM Cortex-M4 core with 256 KB RAM and 1 MB Flash, plus a USB 2.0 full-speed interface that is USB-IF certified. Technically, the module fuses three positioning engines: LR1110 Wi-Fi and GNSS scanning delivers indoor/outdoor fixes without acquiring full satellite signals, the MT3333AV provides standalone high-performance GNSS, and LoRaWAN uplink transports position and telemetry to network servers such as those used by Abeeway-based tracking solutions. The evaluation board exposes the module interfaces, antenna connections (antenna not included on the module), and USB connectivity for rapid prototyping. Typical applications include battery-powered asset trackers for logistics, industrial equipment monitoring, indoor/outdoor personnel and livestock tracking, and smart-city IoT sensors that need multi-year battery life. The 4.7 uA sleep current enables designs that run for years on a primary lithium cell. Design consideration: budget antenna selection and RF layout early, since the module ships without an antenna and GNSS/Wi-Fi/LoRa performance depends heavily on placement and ground-plane design. This page synthesizes distributor availability, datasheet-derived specifications, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
LBUA5QJ2AB-828 - UWB + BLE 5.2 Combo Module | Murata
LBUA5QJ2AB-828

LBUA5QJ2AB-828 - UWB + BLE 5.2 Combo Module | Murata

The Murata LBUA5QJ2AB-828 is a hostless UWB (ultra-wideband) + Bluetooth 5.2 Low Energy combo transceiver module supporting UWB operation across the 6250 MHz to 8250 MHz range (IEEE 802.15.4z channels, Band 5 and Band 9) in a compact 10.5 x 8.3 mm surface-mount LGA package with 97 pins. Antenna is not included, allowing design flexibility with external UWB and BLE antennas. An ultra-wideband module is a short-range, high-precision radio module that transmits nanosecond-scale pulses across very wide bandwidths, enabling centimeter-level distance measurement (secure ranging) that narrowband radios such as Bluetooth or Wi-Fi cannot achieve. UWB modules sit within the broader RF transceiver module hierarchy, and combo modules like this one pair UWB ranging with a conventional low-power radio for wake-up, control, and data functions. Key features include the Qorvo QM33120W UWB chipset paired with an integrated Nordic Semiconductor nRF52840 that provides Bluetooth 5.2 LE, firmware update, and wake-up control. The module is FCC/IC/TELEC reference certified, dramatically reducing end-product regulatory effort. An integrated 3-axis accelerometer supports battery-saving duty cycling, and reference clocks for both the UWB chip and MCU are embedded on the module, simplifying BOM and calibration. Architecturally, the hostless design means the nRF52840 manages the UWB radio autonomously, allowing UWB ranging sessions to execute without waking the host processor. The nRF52840 provides 1 MB flash and 256 kB RAM for embedded application code, with host interfaces including I2C, SPI, UART, and USB. Typical applications include secure car-access key fobs and automotive door-zone detection, indoor asset tracking and real-time location systems (RTLS), and smart-door locks and access-control systems where UWB secure ranging prevents relay attacks. Design consideration: since the antenna is not integrated, place the module near the antenna connectors with controlled-impedance RF traces and follow Murata's reference layout for the 6.5 GHz and 8 GHz bands to pass certification. This page synthesizes distributor pricing, cross-reference findings, and design guidance not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
LBWA0ZZ2HK - Sub-1GHz Wi-Fi HaLow 11ah Module | Murata | IoT
LBWA0ZZ2HK

LBWA0ZZ2HK - Sub-1GHz Wi-Fi HaLow 11ah Module | Murata | IoT

The Murata LBWA0ZZ2HK (Type 2HK) is a long-range Sub-1GHz Wi-Fi HaLow system-on-module based on the NEWRACOM NRC7394 chipset, supporting IEEE 802.11ah SISO operation in the 902 MHz to 928 MHz band with a communication range of up to 2 km, packaged as a compact surface-mount connectivity module. A Wi-Fi HaLow module is a wireless connectivity subsystem that implements the IEEE 802.11ah standard, which operates in sub-1 GHz license-exempt spectrum rather than the crowded 2.4 GHz and 5 GHz bands used by conventional Wi-Fi. Within the network hierarchy, it sits between a host microcontroller or application processor and the RF front end and antenna, offloading the full MAC and PHY of the 802.11ah S1G standard. Sub-1 GHz radios trade raw throughput for dramatically longer range, better penetration through walls and foliage, and lower power consumption, making HaLow the Wi-Fi-family choice for IoT mesh and star networks where 2.4 GHz Wi-Fi, BLE, or 802.15.4 range is insufficient. Key features of the LBWA0ZZ2HK include its NRC7394 chipset base supporting 802.11ah SISO, coverage of the 902-928 MHz US band, ultra-low power consumption with advanced sleep features for battery operation, an embedded RTOS with IP-native application support, and Murata-grade module integration that simplifies regulatory certification (FCC ID VPYLBWA0ZZ2HK). Technically, the module integrates the NRC7394 SoC, crystal, RF matching network, and flash into a single shielded land-grid package. The 2 km link range is achieved by combining narrowband sub-1 GHz propagation with the robust modulation and coding schemes of 802.11ah. The embedded RTOS and TCP/IP stack allow the host processor to use simple AT-style or socket interfaces instead of implementing a Wi-Fi stack. Typical applications include smart utility metering, industrial sensor networks, smart-city infrastructure, agricultural monitoring, and battery-powered security and access-control devices - all scenarios where devices are spread over campus-scale distances and must run for years on batteries. Design-wise, provide a clean 3.3 V supply with local decoupling, route the antenna per Murata's FCC integration instructions, and account for HaLow transmit bursts in battery budget calculations rather than using average current alone. This page synthesizes verified manufacturer and distributor data, drop-in alternatives, engineering design notes, and FAQ content not found together in the product brief.

RFQ پەیوەندی
LBWA0ZZ2HL - Sub-1GHz Wi-Fi HaLow 802.11ah Module | Murata
LBWA0ZZ2HL

LBWA0ZZ2HL - Sub-1GHz Wi-Fi HaLow 802.11ah Module | Murata

The Murata LBWA0ZZ2HL (Type 2HL) is a long-range Sub-1GHz Wi-Fi HaLow system-on-module based on the NEWRACOM NRC7394 chipset, supporting IEEE 802.11ah SISO operation from 750 MHz to 950 MHz with data rates up to 15 Mbps, output power up to 17 dBm, and line-of-sight communication range up to 1 km from a 2.7 V to 3.6 V supply. A Wi-Fi HaLow module is a wireless connectivity module that implements the IEEE 802.11ah Sub-1 GHz (S1G) amendment of the Wi-Fi standard. Unlike conventional 2.4 GHz and 5 GHz Wi-Fi, HaLow trades peak bandwidth for substantially greater range, better wall-penetration, and lower power consumption, making it a member of the low-power wide-area (LPWAN) connectivity family alongside LoRa and NB-IoT, while retaining native IP networking and Wi-Fi security. Key features of the LBWA0ZZ2HL include operation across key regional Sub-1 GHz bands (the HL variant covers 750-950 MHz bands for regions such as Europe, Japan and others, while the companion HK variant targets 902-928 MHz), ultra-low power consumption for battery-powered IoT endpoints, and data rates up to 15 Mbps - far higher than typical LPWAN technologies. The integrated NRC7394 SoC handles MAC, baseband and RF in a single chipset, simplifying host integration over SDIO/SPI interfaces. Technically, the module implements 802.11ah SISO with standard Wi-Fi security, allowing direct IP connectivity to HaLow access points. Murata, as a leading module manufacturer, provides certification-ready design that reduces end-product regulatory burden across key regions. According to Murata product literature, the Type 2HL is designed specifically for the connectivity needs of Internet of Things (IoT) devices. Typical applications include smart utility metering, industrial sensors, building automation, smart city infrastructure, and agricultural monitoring - all scenarios requiring multi-hundred-meter to kilometer-scale links with years of battery life. Designers should verify regional RF regulatory certification (the HL and HK variants cover different frequency bands) and confirm antenna matching and supply filtering per the manufacturer datasheet. This page synthesizes verified distributor and manufacturer data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
LE910C1-EU - LTE Cat.1 10/5 Mbps Module | Telit Cinterion
LE910C1-EU

LE910C1-EU - LTE Cat.1 10/5 Mbps Module | Telit Cinterion

The Telit Cinterion LE910C1-EU is an LTE Cat.1 cellular IoT transceiver module delivering 10 Mbps downlink and 5 Mbps uplink data rates, compliant with 3GPP Release 10, housed in a compact LGA (land grid array) surface-mount form factor with an optional quad-constellation GNSS receiver supporting GPS, GLONASS, Galileo, BeiDou, and QZSS. An LTE Cat.1 module is a category of cellular RF transceiver module that provides full-duplex LTE connectivity at modest data rates, sitting within the broader hierarchy of cellular modems: M2M module -> LTE transceiver module -> wireless communication IC. Cat.1 is widely adopted as the migration path from 2G/3G for machine-to-machine devices because it uses the existing LTE network infrastructure without the complexity of Cat-M1 or NB-IoT, while still supporting voice and data. Key features of the LE910C1-EU include the 10/5 Mbps throughput profile, 3GPP Rel 10 compliance with Rel 12-ready MTC platform features, integrated TCP/IP and UDP/IP protocol stacks, and peripheral connectivity via USB 2.0 HS, UART, and user-definable GPIOs. These characteristics make it well suited to devices that need dependable, always-on wide-area connectivity without a host-side network stack. The module is part of Telit's flagship xE910 family, whose design-once, use-anywhere philosophy allows LE910C1 variants to serve as pin-to-pin compatible replacements within the same LGA footprint for devices based on earlier 2G, 3G, and LTE family members. The ThreadX RTOS-based firmware platform simplifies application integration, and the LE910Cx family is also offered in Linux-based SKUs for more demanding gateway applications. Typical applications include smart metering, asset tracking and fleet telematics, industrial gateways and routers, security and alarm panels, and connected point-of-sale terminals, where European-band LTE coverage and low-power, long-lifecycle operation are priorities. When designing with the LE910C1-EU, budget for a proper RF layout: the antenna is not included, so PCB antenna feed matching, keep-out zones, and supply decoupling follow the Telit LE910C1 Series hardware user's manual guidance for the LGA footprint. This page synthesizes distributor pricing and availability, drop-in alternatives within the xE910 family, and practical design guidance not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
LM048 - Class 1 Bluetooth RS232 Serial Adapter 100m | LM Technologies
LM048

LM048 - Class 1 Bluetooth RS232 Serial Adapter 100m | LM Technologies

The LM Technologies LM048 is a Class 1 Bluetooth® Serial Adapter (RS232) that provides a secure and reliable wireless link replacing legacy RS232 cables between DTE master devices and DCE peripherals such as printers, data loggers, and digital signalling equipment. Housed in a compact plastic enclosure and billed by the manufacturer as the world's smallest Bluetooth® serial adapter, the LM048 delivers up to 100 m line-of-sight range using an onboard antenna while operating from either RS232 Pin 9 (4 V to 13 V) or a Mini-USB supply. A Bluetooth® serial adapter is a self-contained cable-replacement module that bridges a wired RS232 UART interface to a Bluetooth SPP/Serial Port Profile link. Inside the adapter, a Bluetooth baseband IC handles the v2.0/v2.1 + EDR radio (Class 1, up to +18 dBm Tx) and the SPP stack; an RS232 transceiver converts UART logic levels to the ±5 V to ±15 V signaling required by RS232 peripherals. Pairing is transparent to the host: RS232 control lines DTR, DSR, RTS, and CTS are replicated end-to-end over the wireless link via the LM048's patented firmware, allowing legacy Windows/Linux serial applications to operate without modification. The headline specifications include Bluetooth® v2.0/v2.1 with EDR (3 Mbps nominal), Class 1 output power (approximately +18 dBm Tx), -86 dBm Rx sensitivity, and adaptive frequency hopping across the 2.402 GHz to 2.480 GHz ISM band. The adapter accepts RS232-standard baud rates (typical coverage 1.2 kbps up to 460 kbps per public listings) and operates from -20 °C to +75 °C. Power can be sourced from RS232 Pin 9 (4 V to 13 V) or from a Mini-USB port, and the plastic housing exposes a slide switch plus LEDs for status and pairing feedback. A pair of LM048 adapters using their unique hardware and firmware combination can act as a transparent serial cable replacement, removing the need for driver changes on the host. The unit carries relevant Bluetooth SIG certifications and CE/FCC compliance marks as listed in the manufacturer datasheet. Typical applications include industrial RS232 cable replacement, factory-floor data loggers, point-of-sale printers, bar-code scanners, and remote telemetry units. Designers typically route 5 V to 9 V to Pin 9 and connect TX/RX directly to the host UART bridge. When designing a drop-in cable-replacement node, choose between powering from the RS232 Pin 9 line or USB Mini; a pair of LM048 units gives a true transparent null-modem replacement. Note that throughput tops out near the 460 kbps baud ceiling and the radio is limited to Bluetooth v2.0/v2.1 + EDR, not BLE 5.x. This page synthesizes distributor pricing for the LM048, same-brand LM Technologies variants (LM048 v2, LM058, LM400, LM072) and practical drop-in guidance not collected in the manufacturer datasheet.

RFQ پەیوەندی
LM068 - Bluetooth 5.0 Dual Mode RS232 Serial Adapter | LM Technologies
LM068

LM068 - Bluetooth 5.0 Dual Mode RS232 Serial Adapter | LM Technologies

The LM Technologies LM068 is a Bluetooth 5.0 Dual Mode RS232 Serial Adapter packaged as a standalone module with an embedded Bluetooth 5.0 stack. It operates with a supply voltage of 4V to 12V, supports data rates up to 3 Mbps, and is designed to replace wired RS232 cables between a master (DTE) device and slave (DCE) devices such as printers, data loggers, and digital signalling instruments. The adapter runs on an internal microcontroller paired with an 8 Mbit flash memory for application storage, enabling firmware configurability through the LM149v2 host utility. A Bluetooth serial adapter is a self-contained wireless bridge that replaces a legacy UART/RS232 cable with a Bluetooth link. In the broader taxonomy it sits under wireless modules -> RF modules -> RF transceivers -> communication ICs -> semiconductors. The adapter exposes a standard DB9 RS232 connector on the DTE side and converts the UART traffic to a Bluetooth 5.0 link on the slave side. Dual Mode means it can connect to both Bluetooth Classic (BR/EDR) and Bluetooth Low Energy (BLE) hosts, providing flexibility for legacy SPP-style serial replacement as well as modern low-power BLE devices. Key features of the LM068 include Bluetooth 5.0 dual mode support (Classic + BLE), a configurable firmware via the LM149v2 utility, configurable baud rate, data bits, parity and flow control, support for SPP (Serial Port Profile) over Classic, and a small physical footprint of 46.3 mm x 34 mm x 16 mm. The power input is versatile: USB-Mini, DB9, or an external AC adaptor. Settings persist across power cycles, eliminating the need to reconfigure on every boot. The adapter also supports auto-connect and discoverable/non-discoverable modes, simplifying integration in industrial machines where operators frequently reconnect cables between cycles. The internal architecture pairs a microcontroller with a Bluetooth 5.0 module, with the MCU handling profile bridging and configuration. Because the stack is embedded, the host CPU never sees raw radio activity; it only exchanges UART bytes, simplifying software integration on systems that cannot host a Bluetooth stack (older PLCs, microcontrollers without BLE, lab instruments). Typical applications include replacing RS232 cables in industrial machinery, wireless connection to data loggers and printers, point-to-point serial tunneling for embedded devices, and office equipment that needs occasional wireless configuration access without permanent cabling. The wide 4-12V input range lets it draw power from the host's existing DC rail or an AC wall adaptor. When selecting the LM068, ensure that the target host device has an RS232 DB9 port, or plan for a USB-to-RS232 converter. The adapter cannot exceed approximately 3 Mbps aggregate throughput, which is faster than classic RS232 (115.2 kbps typical) but considerably slower than modern Wi-Fi or Ethernet alternatives. Pick this part when you need a deterministic cable replacement with minimal configuration, not for high-bandwidth streaming. This page synthesizes distributor availability, configuration guidance and drop-in alternative notes that complement the manufacturer's datasheet. Compared to bare Bluetooth modules the LM068 is a finished adapter with connectors and firmware, so its alternatives must also be finished serial adapters in the same form factor, not bare radio modules.

RFQ پەیوەندی
LM509 - Bluetooth 5.4 Dual Mode Class 1 USB Adapter | LM Technologies
LM509

LM509 - Bluetooth 5.4 Dual Mode Class 1 USB Adapter | LM Technologies

The LM Technologies LM509 is a Bluetooth 5.4 dual mode Class 1 USB adapter that provides plug-and-play wireless connectivity for host computers. Housed in an ultra-small form-factor USB dongle, it supports Bluetooth 2.x, 4.x, and 5.x profiles, enabling communication with iOS, Android, printers, keyboards, speakers, and headphones using both Bluetooth Classic (BR/EDR) and Bluetooth Low Energy (LE) radio paths. According to the LM Technologies LM509 datasheet, the adapter is compatible with Linux as well as Windows 10 through Windows 11 host platforms. Background knowledge: Bluetooth dual mode adapters are external peripherals that aggregate a Bluetooth Classic radio (for legacy audio, HID, and SPP profiles) and a Bluetooth Low Energy radio (for modern IoT, beacon, and low-power sensor profiles) onto a single USB endpoint. They are classified as Class 1 when their transmit output power reaches up to +20 dBm and supports an indoor range of roughly 30 meters, which extends coverage well beyond the Class 2 limit (~10 m) used in most laptops. Bluetooth 5.4 itself is a core specification released by the Bluetooth SIG that adds PAwR (Periodic Advertising with Responses), LE-Game-Controller profile support, and encrypted advertisement data, in addition to the 2x throughput and 4x range improvements of Bluetooth 5.0. Key specifications of the LM509 include its dual-mode Bluetooth 5.4 radio, Class 1 transmit power, USB Type-A plug-and-play interface, and OS coverage from Windows 10/11 to mainline Linux kernels. The adapter exposes dual radio paths (BR/EDR + LE) so a host can pair both legacy audio peripherals and modern BLE sensors simultaneously. Bluetooth 5.4 features supported include advertising extensions, periodic advertising with responses, and LE audio metadata. The product is supplied as a finished, end-user-ready module, not a bare silicon IC. Its architecture centers on a Bluetooth 5.4 SoC paired with a Class 1 RF front-end, USB 2.0 device controller, and integrated PCB antenna or external RF chain depending on the SKU variant. The completed enclosure is tested by the manufacturer for EMC and RF conformance, which removes RF tuning work from the integrator. Typical use cases include adding wireless audio and HID connectivity to industrial PCs, providing BLE data uplink for IoT gateways, and acting as a development dongle during Bluetooth firmware bring-up. For successful deployment, verify that the host OS supplies USB HID/Bluetooth enumeration support and that Class 1 radio emissions comply with the regional ETSI/FCC/IC radio regulations at the installation site. The USB bus supplies the device with 5 V at roughly 100 mA, so no external power is required.

RFQ پەیوەندی
LM808 - 433 Mbps Wi-Fi 5 USB Adapter | LM Technologies
LM808

LM808 - 433 Mbps Wi-Fi 5 USB Adapter | LM Technologies

The LM Technologies LM808 is a 433.3 Mbps Wi-Fi 5 (802.11ac) USB 2.0 wireless client adapter designed for users requiring high-performance wireless connectivity on desktop and embedded hosts. Built around a Realtek 1T1R (one transmit, one receive) radio chipset, the LM808 fully supports all 802.11 bands including IEEE 802.11ac Draft 2.0 and the legacy 802.11 a/b/g/n specifications, while remaining backward compatible on 802.11n networks. Housed in a compact USB dongle form factor, the LM808 exposes the full 433 Mbps physical-layer rate available on a single spatial stream under 802.11ac, and is paired with a USB 2.0 device interface that draws bus power directly from the host. A Wi-Fi USB adapter is a peripheral module that bridges a host computer's USB bus to a wireless local area network (WLAN). The adapter's internal radio and baseband translate 802.11ac/a/b/g/n OFDM frames into USB packets, allowing any operating system with a generic WLAN driver stack to treat the device as a virtual Ethernet port. Within the wireless-networking taxonomy, the LM808 sits below embedded SiP modules and above raw chip-down radio designs, giving product developers a pre-certified, drop-in connectivity solution without needing to manage antenna matching or RF regulatory compliance themselves. Key features include dual-band 2.4 GHz and 5 GHz operation, Wi-Fi Direct peer-to-peer support for ad-hoc PAN-style networking, 1T1R MIMO, and full USB 2.0 high-speed bus compatibility. The adapter relies on OFDM modulation across the supported 802.11 bands and uses the host's WLAN driver stack to negotiate rates up to 433.3 Mbps. The Realtek-based design has been validated across Windows, Linux, and macOS reference stacks supplied by LM Technologies, removing the need for proprietary driver development. Typical applications include upgrading legacy desktop PCs to dual-band Wi-Fi 5, adding wireless connectivity to industrial PCs and point-of-sale terminals, embedded Linux gateways, retro gaming consoles, and digital signage players. The compact USB-A dongle footprint also makes the LM808 a convenient wireless client for developer boards that lack an on-board Wi-Fi radio, where it can be paired with a Linux host running NetworkManager or wpa_supplicant. When designing with the LM808, verify host-side driver availability for the target operating system and confirm the antenna's radiation pattern is appropriate for the enclosure. USB 2.0 bus-power limits must be observed when designing hubs that will host multiple LM808 adapters in parallel. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for evaluating the LM808 against competing USB Wi-Fi 5 adapters.

RFQ پەیوەندی
LM813 - WiFi 802.11ac + BT 4.2 Combi Module | LM Technologies
LM813

LM813 - WiFi 802.11ac + BT 4.2 Combi Module | LM Technologies

The LM Technologies LM813 is a combination WiFi 802.11ac/a/b/g/n plus dual-mode Bluetooth v2.1/v3.0/v4.2 module delivered as a surface-mount device with an IPEX antenna connector. The module supports WiFi data rates to 433 Mbps and Bluetooth EDR to 2 Mbps (HS mode to 3 Mbps), exposing USB plus GPIO terminals for coexistence signaling in a single compact RF module footprint. A WiFi + Bluetooth combo module is a System-in-Package (SiP) or module-level integration of two radio subsystems (WiFi IEEE 802.11 family and Bluetooth) on a shared PCB, allowing a host processor to add wireless connectivity without designing RF matching networks or managing complex coexistence arbitration in firmware. Combo modules fall within the broader category of RF modules > wireless modules in the connectivity hierarchy. They are commonly deployed when BOM simplification, certified radio performance, and reduced time-to-market outweigh the need for lowest unit cost at scale. Key features of the LM813 include dual-band 2.4 GHz and 5 GHz WiFi operation under the IEEE 802.11ac/a/b/g/n standard family, dual-mode Bluetooth (Classic BR/EDR plus Bluetooth 4.2 LE) for backwards compatibility with legacy audio and data accessories, and an integrated coexistence interface exposed through GPIO pins for arbitration with co-located radios. The module carries an external IPEX/MHF antenna receptacle, allowing antenna selection to be tuned for the end application. The LM813 is built around a combination chipset that implements the 802.11ac MAC/PHY and Bluetooth baseband on a single die. WiFi throughput of 433 Mbps is delivered over a single spatial stream (1x1 SISO) using 802.11ac's mandatory MCS9 modulation, while Bluetooth uses an EDR-capable radio supporting 2 Mbps (HS mode 3 Mbps). The architecture offloads coexistence, channel access, and link-layer management from the host, leaving the host application processor responsible for higher-level networking (TCP/IP, BLE GATT services). Typical applications for the LM813 include industrial IoT edge gateways that need both WiFi infrastructure connectivity and Bluetooth for local provisioning or sensor beacons, point-of-sale (POS) terminals that accept Bluetooth card readers or barcode scanners while joining the store WiFi, and embedded HMI panels requiring over-the-air firmware updates. The dual-band capability also suits consumer audio docks that stream WiFi while maintaining a Bluetooth fallback path. When designing with the LM813, engineers should review the host interface (USB) pin mapping and supply the module from a clean 3.3 V rail with adequate decoupling. Antenna placement and ground keep-out around the IPEX feed line directly affect radiated performance and regulatory compliance. This page synthesizes distributor references, host-interface guidance, and verified parametric data not consolidated in the LM Technologies datasheet.

RFQ پەیوەندی
LM816 - 150Mbps WiFi 4 USB Nano Adapter | LM Technologies
LM816

LM816 - 150Mbps WiFi 4 USB Nano Adapter | LM Technologies

The LM Technologies LM816 is a WiFi 4 (802.11 b/g/n) USB Nano wireless adapter delivering up to 150 Mbps PHY rate, built around a Realtek RTL8188EUS chipset and housed in a compact USB-A dongle form factor. Designed for low-power 5V operation via the USB bus, it supports both ad-hoc and infrastructure mode network architectures and is fully compliant with IEEE 802.11n, b, g, e and i standards including 802.11e QoS and 802.11i security extensions. The integrated chip antenna (IC-ANT) keeps the BOM minimal, making the LM816 well suited to space-constrained host platforms such as single-board computers, industrial gateways, and embedded Linux/Windows devices. A Wi-Fi 4 (802.11n) USB adapter is a peripheral that converts a wired USB host port into a wireless network client operating in the 2.4 GHz ISM band, providing 1x1 SISO throughput up to 150 Mbps and supporting legacy 802.11b/g fallback. In the broader hierarchy, the LM816 sits under wireless LAN adapters -> networking peripherals -> computer interfaces, and uses a single spatial stream with 20 MHz channels and 40 MHz HT capability. This product class is widely adopted for legacy Wi-Fi connectivity on embedded systems where cost, footprint, and driver maturity matter more than the multi-gigabit throughput of newer Wi-Fi 6/6E modules. Key features include hardware-based 64/128-bit WEP, WPA, and WPA2 encryption, soft-AP / Wi-Fi Direct capability, and driver support for Windows, Linux, and macOS hosts. The adapter enumerates as a USB 2.0 high-speed device and uses the standard RTL8188EUS driver tree maintained by Realtek and the Linux community. An internal printed chip antenna (AO/IC-ANT) eliminates the need for an external antenna while preserving the link budget required for typical indoor ranges. The LM816 references the Realtek RTL8188EUS single-chip 802.11n controller, which integrates the MAC, baseband, RF transceiver, and PA on a single die, requiring only an external crystal, EEPROM, and antenna matching network. The 1T1R radio chain, combined with Short GI and MCS7 modulation, enables the headline 150 Mbps PHY rate while staying within USB 2.0 bus bandwidth. This architecture explains the module's low power consumption and small footprint compared to discrete solutions. Typical applications include retrocomputing and embedded Linux SBCs (Raspberry Pi, Toradex, BeagleBone), industrial HMI terminals, point-of-sale systems, digital signage media players, and low-cost retrofit wireless upgrades for older desktops or laptops. The LM816 is also used as a quick evaluation reference for engineers validating 2.4 GHz Wi-Fi link behavior in prototype designs. When integrating the LM816, ensure the host platform provides a USB 2.0 high-speed port with sufficient bus power (typically 500 mA @ 5V). RF performance is sensitive to USB cable length and chassis shielding; for chassis-mounted applications, route the dongle externally to avoid degrading antenna patterns. Verified driver compatibility with the host OS should be confirmed before deployment in production. This page synthesizes distributor pricing, drop-in adapter alternatives, and application notes not found in the manufacturer datasheet, helping engineers select the right Wi-Fi adapter for embedded and industrial deployments.

RFQ پەیوەندی
LM816-USB - 150Mbps Wi-Fi 4 USB Nano Adapter | LM Technologies
LM816-USB

LM816-USB - 150Mbps Wi-Fi 4 USB Nano Adapter | LM Technologies

The LM Technologies LM816-USB is a Wi-Fi 4 (802.11b/g/n) USB Nano Adapter that delivers up to 150 Mbps data transfer in a compact USB dongle form factor. It is built around a Realtek 8188EUS chipset and is fully compliant with IEEE 802.11 b, g, and n standards, including 802.11e and 802.11i features. The adapter operates in the 2.4 GHz ISM band and supports both ad-hoc and infrastructure network architectures. A USB Wi-Fi adapter (also called a WLAN dongle) is a peripheral that adds wireless networking capability to a host device via the USB bus. It encapsulates the radio, baseband, MAC, and host interface into a self-contained module, allowing embedded systems, single-board computers, and PCs to join Wi-Fi networks without integrating a chipset directly on the motherboard. Within the wireless connectivity hierarchy, USB Wi-Fi adapters sit alongside PCIe Wi-Fi cards, SDIO Wi-Fi modules, and solder-down M.2 WLAN cards as one of the easiest ways to add Wi-Fi to a design. Key features of the LM816-USB include a 1T1R (single transmit / single receive) radio chain, 20 MHz channel bandwidth, and 64/128-bit WEP, WPA, and WPA2 encryption. The adapter is powered directly from the USB 5 V rail, eliminating the need for an external power supply. A reference designator on the product page identifies it as "ADT, 802.11n, USB, 150Mbps, 5V Realtek 8188EUS, Nano". The adapter is pre-certified, which shortens time-to-market for OEMs that would otherwise need to certify a discrete radio. The LM816-USB uses a Realtek RTL8188EUS single-chip 802.11n controller, which integrates the 2.4 GHz radio, MAC, and baseband. The dongle presents a USB 2.0 device to the host and exposes a Wi-Fi station through the standard WLAN NDIS / nl80211 interface on Linux or the Wi-Fi NDIS miniport on Windows. This chipset family is broadly supported by mainline Linux kernels, simplifying driver integration on embedded Linux hosts (note: Toradex lists the LM816 as HCI for Windows CE; embedded Linux support depends on the kernel version in use). Typical applications include adding Wi-Fi to Raspberry Pi or other SBC projects, industrial control panels requiring wireless network access, point-of-sale terminals needing network connectivity, retro computing projects that need network access on legacy hardware, and embedded Linux development boards that lack an on-board Wi-Fi chipset. Its 150 Mbps link rate is sufficient for typical browser, email, and IoT telemetry workloads. When designing with this adapter, consider that the USB connector orientation and dongle clearance must be planned at the chassis level. Because the radio radiates through the dongle body, the USB port should be positioned away from large metal structures that attenuate 2.4 GHz signals. For best throughput, place the host within line-of-sight of the access point and avoid operating near 2.4 GHz interference sources such as microwave ovens and Bluetooth peripherals. This page synthesizes distributor inventory, datasheet specifications, chipset architecture, and application guidance for the LM816-USB, providing practical engineering context beyond what the manufacturer datasheet alone offers.

RFQ پەیوەندی
LM822 - 802.11 b/g/n WiFi Module with IC Antenna, USB HCI | LM Technologies
LM822

LM822 - 802.11 b/g/n WiFi Module with IC Antenna, USB HCI | LM Technologies

The LM Technologies LM822 is a WiFi 802.11 b/g/n module operating in the 2.4 GHz ISM band with an onboard chip (IC) antenna and a USB Host Controller Interface (HCI). It supports the IEEE 802.11b, 802.11g and 802.11n standards and delivers data rates up to 150 Mbps on a single stream, packaged as a plug-and-play USB module for OEM integration. What is a WiFi 802.11n (WiFi 4) module? A WiFi 4 (802.11n) module is an embedded radio subsystem that implements the IEEE 802.11n physical and MAC layers and exposes either a host-controlled (HCI) or full-stack (network) interface to the host processor. The LM822 specifically implements HCI over USB, meaning the host CPU runs the network stack and the module acts as a 2.4 GHz radio front-end. These modules sit in the wireless connectivity layer of an embedded system, above the physical RF transceiver and below the application networking stack, and are widely used to retrofit wireless capability into industrial PCs, single-board computers, point-of-sale terminals and gateways. Key specifications of the LM822 per the LM Technologies datasheet include a 150 Mbps PHY rate, BPSK/QPSK/16-QAM/64-QAM modulation, WEP/TKIP/AES plus WPA/WPA2 encryption, a built-in IC antenna (no external antenna or RF connector required), and Linux/macOS/Windows 10 IoT Core/Windows XP to Windows 10/Windows Compact Embedded 6/7 driver support. Compliance with 802.11e bursting and 802.11I standards is also listed. The module draws 5 V through the USB bus and uses the USB port as both the data interface and the power rail. Because all protocol stacks are offloaded onto the host OS (it is HCI-only), the LM822 needs no additional firmware flashing for typical OS environments - it enumerates as a USB WiFi adapter. This makes it well suited to industrial PCs and SBCs that need to add wireless connectivity without a custom driver port. Typical applications include retrofitting WiFi onto legacy industrial PCs, adding wireless connectivity to single-board computers in kiosk and POS designs, embedded gateways that bridge Ethernet to 802.11n WiFi, and Windows Compact Embedded terminals. In each case the LM822's USB HCI and plug-and-play OS driver coverage reduce integration effort compared with bare 802.11 ICs. When designing with this module, note that 2.4 GHz operation only means the host system must coexist with Bluetooth, microwave ovens, and other 2.4 GHz interferers common in industrial and consumer environments. Channel planning and adequate placement of the host PCB relative to metal enclosures is critical because the onboard IC antenna's radiation pattern is shaped by the surrounding ground plane. This page synthesises distributor pricing, a feature comparison with adjacent LM Technologies modules, and practical integration notes that go beyond what the manufacturer datasheet alone covers, helping engineers decide whether the LM822 is the right drop-in wireless module for their embedded platform.

RFQ پەیوەندی
LM823 - WiFi 802.11 b/g/n 150Mbps USB Module | LM Technologies
LM823

LM823 - WiFi 802.11 b/g/n 150Mbps USB Module | LM Technologies

The LM823 is a WiFi 4 (802.11 b/g/n) USB module from LM Technologies delivering up to 150Mbps wireless throughput at 2.4 GHz with HCI host interface via USB. It is offered in SMT form factor with an IPEX receptacle (u.FL-compatible antenna connector) and operates from a single 3.3 V supply. The module is designed to provide excellent performance with low power consumption while supporting b/g/n standards with full 150 Mbps PHY rate. A WiFi module is a compact radio subsystem that integrates the RF transceiver, baseband processor, MAC, and host interface (USB, SDIO, SPI, or UART) into a single, certified or pre-certified hardware block. It allows a host processor or embedded MCU to add wireless connectivity without having to design the analog RF chain, antenna matching network, or regulatory radio from scratch. WiFi modules are classified by generation (WiFi 4 = 802.11n, WiFi 5 = 802.11ac, WiFi 6 = 802.11ax), by host interface (USB, SDIO, SPI, UART), and by antenna integration (chip antenna, trace antenna, or external antenna via u.FL/IPEX). Key features of the LM823 include IEEE 802.11 b/g/n compliance, 150 Mbps maximum PHY data rate on a 2.4 GHz single-band radio, USB 2.0 HCI host interface, integrated IPEX/u.FL antenna receptacle for flexible external antenna selection, low-power operation, and a compact SMT package for high-density PCB placement. It is shipped in trays of 40 pieces and supports Linux/Android/Windows host drivers commonly available for USB WiFi dongle-class silicon. The module integrates a 2.4 GHz single-band 1x1 SISO radio with 20 MHz channel bandwidth, supporting DSSS/CCK for 802.11b and OFDM for 802.11g/n. Internally it relies on a USB-attached WiFi SoC whose host drivers are widely packaged in mainline Linux kernels, Android, and Windows, so no proprietary firmware porting is required on common host platforms. The IPEX receptacle allows the integrator to swap a higher-gain external antenna for better link margin in metal-enclosed products. Typical applications include embedded Linux gateways, IoT edge nodes, industrial wireless telemetry, point-of-sale terminals, retrofit WiFi for set-top boxes and media players, and USB-attached wireless connectivity for SBCs and developer boards that lack built-in WiFi. The 150 Mbps PHY rate is sufficient for video streaming up to 1080p, VoIP, and bulk file transfer on a local network. When designing with this module, mount the antenna connector area clear of ground copper and tall components to avoid pattern distortion; route the USB D+/D- pair as a 90 ohm impedance-controlled differential pair with matched length. For regulatory compliance, the modular transmitter typically still requires antenna selection and host-integration testing against FCC/CE rules for the final product. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LM823 that are not consolidated in the LM Technologies datasheet alone.

RFQ پەیوەندی
LM843 - WiFi 802.11ac + BT 5.0 2T2R USB Combo Module | LM Tech
LM843

LM843 - WiFi 802.11ac + BT 5.0 2T2R USB Combo Module | LM Tech

The LM Technologies LM843 is a WiFi 802.11ac plus Bluetooth 5.0 dual-mode combination SMT/USB module in the LM843 series, providing 2-stream 802.11ac with Multi-User MIMO connectivity and integrated power management. Per the LM Technologies product page and datasheet, the module is offered in multiple SKUs covering tray/IPEX and 2x RF line-out antenna options, all sharing the same WiFi+BT 5.0 silicon foundation. A WiFi + Bluetooth combo module is a small surface-mount or USB assembly that packages a WiFi radio, a Bluetooth radio, an RF front-end, a crystal oscillator, and a host interface (USB, SDIO, or UART) into a single, pre-certified hardware block. This module category sits inside the broader taxonomy of RF modules -> RF transceivers -> wireless connectivity ICs -> semiconductors. By integrating both radios, the module reduces BOM, host-side firmware complexity, and time-to-market for devices that need simultaneous WiFi and Bluetooth coexistence. Key features of the LM843 include dual-band 2.4/5 GHz 802.11ac operation in a 2T2R MIMO configuration, Bluetooth 5.0 dual-mode support (Classic BR/EDR 2.1/3.0/3.0+HS and Low Energy 4.0/4.1/4.2/5.0) with multiple simultaneous Classic+LE connections, USB 2.0 host interface, and on-board power management for maximising throughput across coexisting WiFi/BT links. Hardware is BT 5.0 compliant at the silicon level. Architecturally, the LM843 series uses a 2x2 MIMO WiFi subsystem combined with a Bluetooth 5.0 dual-mode radio sharing a single module PCB and antenna chain through an internal coexistence interface. The USB 2.0 interface carries both WiFi and Bluetooth traffic to the host, simplifying driver bring-up versus SDIO+UART split designs. Typical applications include industrial IoT gateways, wireless POS terminals, set-top boxes and media streaming dongles, USB WiFi+BT adapters, in-vehicle infotainment companion radios, and embedded Linux/Windows host platforms requiring a pre-certified combo radio. Design tip: confirm the exact SKU variant - LM843-8432 (tray, 2x IPEX), LM843-8434 (USB, 2x IPEX), LM843-8438 (tray, 2x RF line-out) - matches the desired host interface (USB vs SMT) and antenna connector (IPEX MHF4 vs RF line-out pad) before PCB layout. This page synthesises verified distributor pricing, drop-in alternative notes, and application-level design guidance that are not consolidated in the LM Technologies datasheet alone.

RFQ پەیوەندی
LM845 - WiFi 802.11ac + Bluetooth 4.2 USB Nano Adapter | LM Technologies
LM845

LM845 - WiFi 802.11ac + Bluetooth 4.2 USB Nano Adapter | LM Technologies

The LM Technologies LM845 is a compact WiFi 5 (802.11ac) and Bluetooth 4.2 dual-mode USB nano adapter (dongle) built around a fully integrated single-chip Realtek radio. It operates on the 2.4 GHz and 5 GHz WiFi bands with 1-stream 802.11ac and Multi-user MIMO (MU-MIMO), and it supports Bluetooth v4.2 Dual Mode with backward compatibility to Bluetooth v2.1+EDR and v3.0. Classic Bluetooth and Bluetooth Low Energy (LE) can run simultaneously, enabling concurrent wireless audio/data and BLE beacon use cases over the same USB interface. A WiFi + Bluetooth USB combo dongle is a peripheral that adds short-range wireless connectivity to a host PC, embedded board, or industrial appliance via the USB bus. Inside the dongle, a single radio SoC handles both WiFi (the 802.11 family) and Bluetooth (BR/EDR/LE), sharing one antenna chain through an internal RF front-end. The host sees two logical interfaces (a network interface for WiFi and an HCI interface for Bluetooth) over USB, which simplifies driver integration and shrinks the dongle to a nano form factor that can be left plugged into a laptop or set-top box. Key features of the LM845 include 1-stream 802.11ac Wave-2 operation with MU-MIMO, dual-band 2.4/5 GHz support, Bluetooth 4.2 Dual Mode (BR/EDR + LE) with simultaneous Classic + LE links, a USB 2.0 high-speed host interface, and a Realtek-based single-chip radio that minimizes BOM and power draw. The dongle form factor is sized for always-on installation in laptops, mini-PCs, and industrial HMIs. The internal architecture relies on a Realtek combo MAC/baseband IC with an integrated 2.4/5 GHz PA/LNA chain. WiFi throughput reaches 433 Mbps on the 5 GHz 802.11ac 1x1 link, while Bluetooth supports the standard BR/EDR profiles plus BLE GATT services for IoT pairing and beaconing. Because WiFi and Bluetooth share the same RF chain, the firmware coordinates time-division scheduling to avoid mutual interference. Typical applications include adding dual-band WiFi 5 + Bluetooth to legacy desktop or embedded systems, IoT gateways and industrial PCs that need a quick wireless drop-in upgrade, point-of-sale terminals that pair with BLE peripherals, retrofitted media PCs and set-top boxes that need 5 GHz WiFi for HD streaming, and developer/test rigs that require a stable Realtek-based combo radio for driver qualification. When designing with the LM845, remember that it is a finished USB dongle, not a bare IC: designers cannot change the antenna, regulators, or USB stack. Host drivers must support the underlying Realtek chipset for full 802.11ac + Bluetooth 4.2 functionality, and the host OS USB port must provide enough bus power for the 5 GHz PA under load. This page synthesizes verified distributor information, parametric specifications, and design guidance not consolidated on any single manufacturer or distributor page, including practical notes on host-driver compatibility and concurrent WiFi + Bluetooth operation.

RFQ پەیوەندی
LM848 - Wi-Fi 6 (802.11ax) and Bluetooth 5.2 USB Combo Adapter | LM Technologies
LM848

LM848 - Wi-Fi 6 (802.11ax) and Bluetooth 5.2 USB Combo Adapter | LM Technologies

The LM Technologies LM848 is a USB 3.0 combo adapter that integrates Wi-Fi 6 (802.11ax) and Bluetooth 5.2 connectivity through a single USB Host Controller Interface (HCI) port. Designed for embedded Linux, Windows, and Android hosts, the LM848 exposes a high-throughput wireless pipe without burdening the host CPU with baseband firmware, because the dual-mode radio runs the 802.11ax MAC/PHY and the BT 5.2 controller silicon on-module. The USB 3.0 uplink provides the bandwidth required for 2x2 MU-MIMO, 160 MHz channel operation, and OFDMA scheduling features defined in the 802.11ax amendment. A USB combo adapter is a peripheral that bridges a host processor to two or more wireless radios through a standardized serial bus. In the wider connectivity taxonomy, this places the LM848 as a USB peripheral module -> wireless network adapter -> combo radio module -> RF subsystem, sitting beneath the host's network stack and above the antenna. USB-based combo adapters are favored over SDIO or PCIe cards in industrial and prototyping environments because they avoid slot allocation, simplify thermal management, and survive hot-swap events without rebooting the host. The headline features of the LM848 include 802.11ax 2x2 operation, WPA3 security compliance, dual-band 2.4 GHz / 5 GHz / 6 GHz coverage where supported by regional regulations, Bluetooth 5.2 with LE Audio and Long Range (PHY Coded), and a USB 3.0 Type-A form factor that draws bus power. The device advertises ultra-fast throughput that suits video streaming, edge AI gateways, and dense Wi-Fi deployments where 802.11ac throughput would saturate. Architecturally, the LM848 pairs an 802.11ax SoC with a BT 5.2 companion chip, sharing a single USB endpoint group over a USB 3.0 SuperSpeed link. The radio front end is tuned for worldwide regulatory domains, and the firmware exposes standard nl80211/cfg80201 (Linux) and MediaTek/Realtek-style vendor extensions (Windows) for throughput tuning. Typical applications include industrial IoT gateways, in-vehicle infotainment prototyping, point-of-sale terminals, medical telemetry docks, and digital signage where Wi-Fi 6 capacity and Bluetooth coexistence are both required. When designing with the LM848, ensure the host supplies a USB 3.0 port capable of delivering 900 mA, and place the antenna at least 20 mm from any metal enclosure walls to preserve EIRP margin.

RFQ پەیوەندی