بەرهەمەکان (730+)

BCM5481A2KFBG - 1GbE Copper PHY | Broadcom | Networking
BCM5481A2KFBG

BCM5481A2KFBG - 1GbE Copper PHY | Broadcom | Networking

Broadcom BCM5481A2KFBG is a single-port Gigabit Ethernet Physical Layer transceiver for 10/100/1000BASE-T copper connectivity, with a 1000 Mbps data rate, RGMII MAC-facing interface, and 100-terminal rectangular BGA package. The component combines integrated 10, 100, and 1000 Mb/s copper PHY functions with CMOS technology in a surface-mount grid-array format designed for network-interface equipment. A Gigabit Ethernet PHY is the physical-layer device that converts between a MAC controller's digital data and signals suitable for twisted-pair cabling. In the networking hierarchy, a PHY is a transceiver interface integrated circuit used with a media-access controller, Ethernet switch, router, gateway, or other equipment requiring 10/100/1000BASE-T copper connectivity. The BCM5481A2KFBG therefore handles the physical encoding, signaling, and cable-facing functions while the MAC supplies packet data through RGMII. Key features include support for 10, 100, and 1000BASE-T operation, a 1000 Mbps data rate, an RGMII interface, CMOS construction, and a peak reflow temperature of 260°C. Its single-port architecture suits one copper Ethernet port per device. The 100-terminal rectangular BGA package permits dense board placement, but it also requires a multilayer PCB with conventional via-in-pad or fanout construction, controlled solder paste printing, and careful inspection of hidden joints. The part is positioned for copper Ethernet links in routers, switches, gateways, set-top equipment, industrial networking products, and embedded systems. RGMII provides a parallel MAC-facing connection that can reduce pin count compared with a fully parallel GMII implementation at Gigabit rates. During board design, engineers should preserve the exact reference network, power distribution, grounding, and high-speed clock topology specified by the Broadcom datasheet because PHY performance depends on controlled impedance and low-noise power delivery. Typical implementation places the BCM5481A2KFBG between a RGMII-capable MAC or Ethernet controller and an integrated magnetic module leading to an RJ45 connector. The PHY is used only for copper media; optical-fiber links require a different physical-layer device. System firmware must also configure the PHY through the applicable management interface and validate autonegotiation, link speed, duplex mode, and cable diagnostics. A primary design consideration is BGA assembly. The package has 100 terminals and a 260°C peak reflow rating, but its fine pitch requires stencil design, profile control, and inspection methods suitable for large-array BGAs. Copper pours should provide both electrical return paths and thermal spreading, while analog supply and digital circuitry should be separated according to the manufacturer's layout guidance. This product overview consolidates the confirmed device identity, package information, interface characteristics, sourcing answers, replacement boundaries, and practical PCB considerations. It also distinguishes a same-family MPN change from true pin-compatible alternatives, helping engineers shorten component search and qualification time while preserving the risk controls required for an advanced BGA networking device.

RFQ پەیوەندی
BCM56992B0KFLGG - 25.6Tb/s 400GbE Switch IC | Broadcom
BCM56992B0KFLGG

BCM56992B0KFLGG - 25.6Tb/s 400GbE Switch IC | Broadcom

The Broadcom BCM56992B0KFLGG is a StrataXGS Tomahawk 4 series Ethernet multilayer switch chip delivering 25.6 Tb/s of switching capacity across 64 ports of 400GbE, housed in a high-density FCBGA package. It integrates 50G PAM4 SerDes technology, L2/L3 multilayer forwarding, and data-center-grade telemetry in a single device. An Ethernet switch fabric IC is the core forwarding engine of a network switch: it terminates high-speed SerDes lanes from optical modules or copper PHYs, buffers packets in deep on-chip memory, and performs lookup, classification, and rewrite operations at line rate. In the network hierarchy, it sits above PHY and retimer devices and below the host CPU and software stack (e.g., SONiC, Linux switchdev), forming the packet-processing heart of data center switching platforms. Key features include 64x400GbE or 128x200GbE port configurations, 25.6 Tb/s aggregate bandwidth, 50G PAM4 SerDes lanes for direct connection to 400G DR4/FR4 optics, hardware L2 learning, L3 routing (IPv4/IPv6), ACLs, ECMP, VXLAN overlay support, and advanced telemetry for congestion and latency monitoring. The Tomahawk 4 generation targets hyperscale cloud and AI/ML cluster fabrics where radix and bandwidth density are decisive. Architecturally, the BCM56992B0KFLGG belongs to Broadcom's StrataXGS family, known for scalability, flexibility, and advanced feature integration. The 50G PAM4 SerDes interface doubles lane bandwidth over NRZ 25G designs, allowing 400GbE ports on 8 lanes and reducing PCB layer count and connector cost. Shared packet buffer memory and programmable pipeline stages enable flexible protocol handling without external co-processors. Typical applications include top-of-rack (ToR) and spine switches for hyperscale data centers, AI/ML training cluster leaf-spine fabrics, enterprise core switching platforms, and white-box switch designs running NOS software such as SONiC. High radix and 400GbE density make it well matched to 400G uplink aggregation. Design considerations center on thermal and signal integrity: the FCBGA package requires a carefully engineered heatsink, high-layer-count PCB, and disciplined 50G PAM4 breakout routing. Verify SerDes reach and PCB stackup against Broadcom reference designs before layout release. This page synthesizes distributor availability data, Tomahawk 4 architecture context, and practical design guidance not found in a single datasheet, helping engineers evaluate the BCM56992B0KFLGG against family variants for 400GbE switch designs.

RFQ پەیوەندی
BCM6715B0KFFBG - Wi-Fi 6/6E 4x4 802.11ax SoC | Broadcom
BCM6715B0KFFBG

BCM6715B0KFFBG - Wi-Fi 6/6E 4x4 802.11ax SoC | Broadcom

The Broadcom BCM6715B0KFFBG is a 4x4 IEEE 802.11ax Release 2 Wi-Fi 6/6E MAC/PHY/Radio System-on-Chip (SoC) that operates selectively in the 2.4 GHz, 5 GHz, and 6 GHz bands with a maximum channel bandwidth of 160 MHz. The KFFBG suffix denotes a Broadcom ball grid array package suitable for high-density residential access point platforms. A Wi-Fi SoC integrates the media access controller (MAC), baseband physical layer (PHY), and radio transceiver on a single die, replacing the multi-chip solutions historically used in wireless LAN infrastructure. Within the network silicon hierarchy, the BCM6715 sits at the access-point main-SoC level, above front-end modules and below cloud management platforms, forming the complete RF signal chain together with power amplifiers, switches, and filters. Key capabilities include simultaneous tri-band operation, full 4x4 Multiple-Input Multiple-Output (MIMO) radio architecture, and 160 MHz channel support that enables multi-gigabit PHY rates under the Wi-Fi 6/6E (802.11ax) standard. Release 2 (Version 2) features add Enhanced Long Range (Wi-Fi 6 R2) functionality for improved uplink and coverage in dense residential environments. The device targets residential wireless access points, mesh Wi-Fi systems, and gateway routers that must serve high client density across the newly opened 6 GHz band. Broadcom positions the BCM6715 as the flagship 4x4 AP chip for premium tri-band home networking platforms. Designers should plan power delivery, thermal spreading via the BGA package land pattern, and RF front-end matching per Broadcom reference designs; full electrical and register-level documentation is distributed under NDA through Broadcom docSAFE rather than a public datasheet. Note: Broadcom does not publish a public datasheet for this part; detailed parameters (power consumption, interface details, supply voltages) require an NDA, so several fields on this page are marked as data-needed pending verification. This page synthesizes distributor pricing and availability (LCSC, Octopart, JLCPCB), category context, and practical sourcing guidance not available in any single public source.

RFQ پەیوەندی
BCM8073CIFBG - Dual 10GBASE-KR Transceiver | Broadcom
BCM8073CIFBG

BCM8073CIFBG - Dual 10GBASE-KR Transceiver | Broadcom

Broadcom BCM8073CIFBG is a dual-channel serial 10GBASE-KR Ethernet transceiver that operates from a 3.3 V supply and supports link rates of 1.25 Gbps and 10 Gbps. The device is packaged in a 324-ball BGA and is identified as a 10GbE and 10GFC XAUI-to-XFI LANPHY interface. Its dual-channel architecture supports high-speed backplane, data-center, and network-interface designs requiring 10GBASE-KR physical-layer connectivity. A 10GBASE-KR transceiver is a physical-layer semiconductor that converts parallel digital data into high-speed serial signals for transmission over printed-circuit-board backplanes and converts incoming serial signals back into parallel data. In the broader networking hierarchy, BCM8073CIFBG belongs to the Ethernet transceiver class, which supports network interface controllers, switches, routers, servers, and data-center equipment. The XAUI-to-XFI LANPHY positioning provides a bridge between a high-speed parallel Ethernet interface and an XFI serial physical-layer path. The principal device characteristics are its two serial channels, 10GBASE-KR operation, 1.25 Gbps and 10 Gbps link-rate support, 3.3 V supply operation, and 324-ball BGA package. The dual-channel configuration allows one physical-layer device to serve two high-speed serial links, reducing component count and simplifying board planning compared with two separate single-channel devices. Broadcom markets the BCM8073 family for 10GbE and 10GFC applications where PCB signal integrity and deterministic high-speed connectivity are central design concerns. The BCM8073CIFBG belongs to a specialized Ethernet physical-layer product family rather than a general-purpose interface controller. Its serial architecture supports systems in which a network processor or switch ASIC exchanges data with a physical-layer device. The 324-ball BGA provides a high pin count suitable for parallel logic, power distribution, clocking, configuration, and multiple high-speed serial interfaces, but it also requires careful escape routing and controlled reference-plane design around the package. Typical applications include 10GbE backplane equipment, 10GFC interconnect fabrics, data-center switches, server network interfaces, and high-throughput aggregation systems. In a backplane design, the BCM8073CIFBG can provide 10GBASE-KR connectivity over controlled PCB channels. In a network-interface card, it can pair a network controller with a serial backplane or front-panel interface. Its dual-channel organization is particularly useful when adjacent links share power, clock, and thermal conditions. The primary design consideration is PCB signal integrity at 10 Gbps. Short reference planes, continuous return paths, suitable loss management, and tightly controlled connector or package transitions are essential. Decoupling and clock distribution must be planned according to the manufacturer’s reference circuit, while BGA assembly requires a package-specific land pattern, solder mask, and thermal design capable of dissipating device power. This product record combines the identified Broadcom device characteristics, interface positioning, package information, compliance status, application guidance, and design considerations. It also distinguishes the BCM8073CIFBG from unrelated Ethernet PHYs that cannot replace it because they use different packages, protocols, or electrical interfaces.

RFQ پەیوەندی
BCM84758AKFSBLG - 40G Ethernet Transceiver | Broadcom
BCM84758AKFSBLG

BCM84758AKFSBLG - 40G Ethernet Transceiver | Broadcom

The Broadcom BCM84758AKFSBLG is a high-speed Ethernet transceiver IC designed for 40G networking applications, housed in a Broadcom proprietary surface-mount package optimized for high-density line-card and switch-fabric layouts. It is part of the Broadcom BCM84758 family and is specified for telecom and datacom infrastructure where robust SERDES links are required. An Ethernet transceiver is a mixed-signal integrated circuit that combines a physical coding sublayer (PCS), physical medium attachment (PMA), and analog front-end to serialize, deserialize, and condition multi-gigabit data streams between a Media Access Controller (MAC) and an optical or copper physical medium. The BCM84758AKFSBLG sits within the hierarchy: ethernet transceiver -> PHY -> network interface IC -> wired communication semiconductor. The category exists because modern switches and routers require dense multi-lane I/O that scales to data-center and carrier-grade line rates. Key features of the BCM84758AKFSBLG include 40G Ethernet data-rate capability, low power consumption suitable for high-density port-count line cards, integrated SERDES with adaptive equalization, and compliance with industry-standard high-speed networking interfaces. The device supports hot-pluggable module integration and is intended for use behind QSFP modules or with on-board optical engines. Architecturally, the part leverages a high-performance CMOS mixed-signal process that combines a multi-gigabit analog front end with digital PCS logic. Adaptive equalization, pre-emphasis, and receive-signal-conditioning circuitry compensate for channel loss at 10+ GHz fundamental frequencies, enabling robust BER performance over typical FR4 backplane channels and direct-attach copper assemblies. Typical applications include 40G Ethernet line cards in top-of-rack switches, QSFP module interfacing in aggregation switches, datacenter fabric interconnects, and telecom OTN/PTN platforms. Low power is essential because line cards may host 24 to 48 such transceivers, and thermal density quickly becomes a board-level constraint. When designing with this part, PCB layout must follow strict high-speed signal-integrity practices: controlled-impedance differential traces, length matching within Skew budget, and a contiguous reference plane on layer 2 directly beneath the SERDES lanes to suppress return-path discontinuities. [DATA_NEEDED: detailed key specs to be confirmed against the manufacturer datasheet PDF]. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet to help sourcing engineers and PCB hardware designers quickly evaluate the BCM84758AKFSBLG for their 40G networking builds.

RFQ پەیوەندی
BCM89836A0BFBG - 100BASE-T1 Automotive Ethernet PHY | Broadcom
BCM89836A0BFBG

BCM89836A0BFBG - 100BASE-T1 Automotive Ethernet PHY | Broadcom

The Broadcom BCM89836A0BFBG is an automotive-grade 100BASE-T1 Ethernet PHY (physical layer transceiver) single-pair Ethernet solution from Broadcom Limited, classified by distributors as an RF/Transceiver System-on-Chip device. It implements the IEEE 100BASE-T1 automotive Ethernet standard for in-vehicle networking over a single unshielded twisted pair. Automotive Ethernet PHYs form the physical layer of the modern in-vehicle network hierarchy: the PHY converts digital MAC data into analog signals for transmission over the single twisted pair, sitting below the Ethernet switch and above the copper cable plant. 100BASE-T1 (formerly BroadR-Reach) replaced legacy 100 Mbit/s systems by transmitting transmit and receive signals simultaneously in full-duplex mode over one pair, saving wiring weight and cost in vehicles. Key characteristics of the BCM89836 family include single-pair full-duplex 100 Mbit/s operation, automotive temperature capability, low electromagnetic emissions suitable for unshielded cabling, and support for power-saving modes demanded by telematics and body-electronics modules. According to Mouser, the part is catalogued as an RF System on a Chip - SoC 100BASE-T1 PHY, confirming its role as a highly integrated PHY SoC rather than a discrete transceiver front end. Architecturally, the device integrates the analog front end, DSP-based equalizers, echo cancellation and clock recovery needed to achieve reliable 100 Mbit/s communication over a single pair at distances used in vehicle topologies. Integration reduces the bill of materials versus discrete PHY plus magnetics approaches, and helps meet the strict EMI budgets of antenna-proximate modules. Typical applications include automotive camera links for surround-view and driver-monitoring systems, ADAS sensor networks, telematics control units, gateway modules, infotainment backbones, and battery management communication in electric vehicles - anywhere a compact, low-cost, EMI-friendly 100 Mbit/s in-vehicle link is required. When designing this part in, verify the exact package dimensions, pinout and supply rails against the official Broadcom datasheet, and follow the manufacturer reference schematic for MDI termination, magnetics and decoupling, since single-pair PHY performance is highly layout dependent. This page synthesizes distributor pricing and availability, cross-reference research results, and practical design notes in one place - information not consolidated in the manufacturer datasheet. All unverified parameters are explicitly flagged rather than guessed.

RFQ پەیوەندی
BGA7L1N6E6327XT - LTE Low Noise Amplifier 728-960MHz | Infineon
BGA7L1N6E6327XT

BGA7L1N6E6327XT - LTE Low Noise Amplifier 728-960MHz | Infineon

The Infineon BGA7L1N6E6327XT is a Silicon Germanium monolithic microwave integrated circuit (MMIC) low noise amplifier (LNA) optimized for LTE receiver front-ends in the 728 MHz to 960 MHz band. It delivers an insertion power gain of 13.3 dB with a low noise figure of 0.90 dB while drawing only 4.4 mA from a 1.5 V to 3.3 V supply. The device is housed in an ultra-small leadless TSNP-6-2 package measuring just 0.7 mm x 1.1 mm, making it one of the smallest LTE LNAs available. A low noise amplifier (LNA) is a critical radio-frequency building block placed immediately after the antenna and the preselect filter that amplifies very weak signals while adding as little noise as possible. LNAs sit at the front of a receiver signal chain - antenna -> filter -> LNA -> mixer/baseband. They are characterized by their noise figure (NF), expressed in dB, which directly sets the overall receiver sensitivity floor. The BGA7L1N6 belongs to the LTE LNA family (LNA -> MMIC -> RF amplifier -> wireless front-end IC) and is targeted at cellular and IoT receive paths that demand both low power and high linearity in a tiny footprint. Key features include 13.3 dB insertion power gain, 0.90 dB noise figure, 4.4 mA operating current, and a digital on/off control pin compatible with 1 V logic to support direct connection to modern baseband GPIO. The part supports external matching, includes an integrated power-down mode, and is qualified over the -40C to +85C operating range. Its bypass-mode-capable topology makes it well suited to time-division duplex (TDD) systems such as LTE Band 8, Band 12, Band 13 and Band 20 terminals. Architecturally, the BGA7L1N6 uses Infineon's high-frequency Silicon Germanium (SiGe) heterojunction bipolar transistor process, which provides high transition frequency at low collector current, a key advantage for low-power RF gain stages. The single-stage design with on-chip bias and matching simplifies the BOM to a few external passives, simplifying PCB layout in densely populated RF modules. Typical applications include smartphones, tablets, LTE-enabled IoT modules, cellular dongles, LTE small cells, and GNSS-protected LTE receivers operating in the 700-960 MHz region. Its miniature footprint enables integration inside the very tight antenna-modules of modern mobile devices. When designing with this part, place it adjacent to the cellular filter and follow Infineon's recommended matching network values in the datasheet - even small deviations above a few hundred MHz can sharply degrade gain and noise figure. Bypass mode is engaged through the 1 V-compatible control pin; routing this pin to a baseband GPIO is the cleanest sequencing approach. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives inside the same TSNP-6-2 package, and application design notes that complement (rather than restate) the Infineon datasheet.

RFQ پەیوەندی
BGA7L1N6E6327XTSA1 - 728-960MHz LTE LNA, 0.9dB NF | Infineon
BGA7L1N6E6327XTSA1

BGA7L1N6E6327XTSA1 - 728-960MHz LTE LNA, 0.9dB NF | Infineon

The Infineon BGA7L1N6E6327XTSA1 is a Silicon Germanium (SiGe) Low Noise Amplifier (LNA) monolithic microwave integrated circuit (MMIC) designed for LTE receiver front-ends covering the 728 MHz to 960 MHz bands (Band 5, Band 8, Band 12, Band 13, Band 17, Band 20 and similar low-band LTE allocations). It integrates a digital on/off switch with 1 V logic high-level threshold, integrates input/output matching networks, and offers an insertion power gain of 13.3 dB while drawing only 4.4 mA from a 1.5 V to 3.3 V supply. An LNA (Low Noise Amplifier) is the first active gain stage in a wireless receiver chain, placed immediately after the antenna and band-select filter. Its function is to amplify extremely weak radio signals captured at the antenna while adding as little noise of its own as possible, thereby setting the receiver's noise floor and overall sensitivity. The BGA7L1N6E6327XTSA1 belongs to the LNA family -> RF amplifier -> RF front-end IC -> wireless transceiver component chain. Its 0.90 dB noise figure directly determines the signal-to-noise ratio at the input of the downstream mixer. Key differentiating features include a sub-1 dB noise figure of 0.90 dB, 13.3 dB insertion power gain across the operating band, an integrated power-on switch controllable from a 1 V logic GPIO, and a current consumption of 4.4 mA typical. The integrated 50 ohm input and output matching eliminates the need for external discrete matching components, reducing PCB footprint, BOM cost, and design cycle time in mass-market smartphone designs. Technically the device uses Infineon's high-frequency SiGe:C process technology, which combines low-noise bipolar HBT (heterojunction bipolar transistor) devices with CMOS control logic on the same die. The internal bias network maintains the LNA's noise figure and linearity across supply, temperature and process variations. The on-chip logic-controlled enable pin allows the LNA to be powered down completely during transmit slots in TDD-LTE systems, saving system current. Typical applications include LTE smartphone and tablet receiver front-ends, cellular IoT modules, 4G USB dongles and mobile hotspots, and diversity antenna chains where two LNAs share a single antenna filter. The device's small TSNP-6-2 leadless package (footprint 0.7 mm x 1.1 mm) enables placement directly adjacent to the antenna switch module. When designing with this LNA, route the RF input and output traces as 50 ohm controlled-impedance microstrip or coplanar waveguide directly from the package pads to minimise parasitic inductance. Place the supply decoupling capacitor within 1 mm of the VCC pin to suppress noise injection from the DC bus. The 1 V logic-high EN input allows direct connection to modern baseband or PMIC GPIOs without level shifters.

RFQ پەیوەندی
BGU8L1UK019 - SiGe:C LNA MMIC for LTE | NXP Semiconductors
BGU8L1UK019

BGU8L1UK019 - SiGe:C LNA MMIC for LTE | NXP Semiconductors

The NXP Semiconductors BGU8L1UK019 is a silicon-germanium-carbon (SiGe:C) low-noise amplifier (LNA) MMIC designed for LTE receiver front-ends up to 2 GHz, housed in a miniature 3-pin lead-frame plastic WLCSP-style package (OL-BGU8L1UK). It targets cellular handset, MiFi, and small-cell applications where board area is at a premium and bias current must be minimized while preserving NF and linearity. An LNA (low-noise amplifier) MMIC is the first active gain stage in a wireless receiver chain, placed immediately after the antenna filter/duplexer and before the down-converting mixer. Its job is to amplify weak RF signals while adding as little noise as possible, characterized by noise figure (NF, in dB), gain, and input-referred IP3 (IIP3). LNAs belong to the RF amplifier family, which itself sits inside the broader signal-chain / RF front-end category of RF & Wireless semiconductors. Key features of the BGU8L1UK019 include very low noise figure, integrated active biasing that flattens performance over temperature, a single positive supply rail, and 50-ohm input/output matching - eliminating the need for external matching components on most cellular bands. The plastic lead-frame package reduces PCB footprint versus wafer-level chip-scale alternatives while retaining the short leadframe parasitics needed at GHz frequencies. Architecturally the part uses a SiGe:C heterojunction-bipolar-transistor (HBT) input stage followed by a cascode, biased from a constant-current source that compensates process and temperature variation. The integrated active bias lets the same PNP-style enable control work across supply voltages of approximately 1.5 V to 3.1 V without external bias resistors. Typical applications include LTE receiver front-ends in smartphones, LTE small-cell and femtocell base-station receivers, MiFi/Mobile-Hotspot modules, LTE USB dongles, and GNSS front-ends sharing the same antenna. The part is well-suited wherever a designer needs a few dB of NF improvement and modest gain in an extremely small outline. Designers should evaluate the part's in-band gain, NF, and IIP3 across the target LTE band (Band 1, 3, 7, 8, 12, etc.) and use the published reference-design evaluation board layout as a starting point, since ground-via placement and supply decoupling directly affect stability. This page synthesizes distributor stock, reference pricing, drop-in alternatives, and practical design notes not typically consolidated on a single manufacturer product page.

RFQ پەیوەندی
BLE112-A-V1 - Bluetooth 4.0 BLE Module w/ Chip Antenna | Silicon Labs
BLE112-A-V1

BLE112-A-V1 - Bluetooth 4.0 BLE Module w/ Chip Antenna | Silicon Labs

The Silicon Labs BLE112-A-V1 is a Class 2 Bluetooth 4.0 low energy single-mode module with an integrated chip antenna, targeting low-power sensors and accessories. It integrates the Bluetooth radio, a microcontroller (based on the TI CC2540), the full BLE software stack, profiles, and customer application space, so no external processor is needed. The module operates from 2.0V to 3.6V and can be powered directly from a standard 3V coin cell or a pair of AAA batteries; in its lowest-power sleep mode it consumes only 400nA and wakes in a few hundred microseconds. A Bluetooth low energy (BLE) module is a type of short-range RF transceiver module in the wireless connectivity family: module -> Bluetooth Low Energy transceiver -> 2.4GHz ISM-band radio -> RF & wireless component. Single-mode BLE devices (Bluetooth Smart) communicate only with BLE-capable devices, offering the lowest possible power consumption compared to dual-mode parts. Key features include full Bluetooth v4.0 single-mode compliance, an integrated chip antenna that eliminates RF layout work, flexible hardware interfaces (SPI and UART) for connecting sensors, user interfaces, or displays directly to the module, and an integrated 8051-based MCU with 18 interrupt sources across six interrupt groups running the Bluegiga (now Silicon Labs) Bluetooth stack. Technically, the module builds on the CC2540 system-on-chip, which combines a 2.4GHz RF transceiver with an industry-standard enhanced 8051 MCU. The Bluegiga firmware implements the complete BLE stack and profiles such as GATT, GAP, and vendor-specific profiles, exposing a simple serial interface for host-less designs. Receiver sensitivity is specified at -85dBm at 0.1% BER, adequate for Class 2 (~10 m line-of-sight) links typical of sensor and accessory designs. Typical applications include battery-powered sensor nodes, fitness and medical accessories, proximity tags, and cable-replacement serial links (UART bridges), where coin-cell life measured in months or years is a hard requirement. Design consideration: keep a keep-out area under the chip antenna free of copper and adjacent RF-absorbing materials, and budget the 2.0V-3.6V supply range so a 3V coin cell remains usable near end of discharge. This page synthesizes distributor pricing, lifecycle status, family replacement options, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
BLE112-A-V1C - BLE 4.0 Module with U.FL Antenna | Silicon Labs
BLE112-A-V1C

BLE112-A-V1C - BLE 4.0 Module with U.FL Antenna | Silicon Labs

The Silicon Labs BLE112-A-V1C is a Class 2 Bluetooth Smart (Bluetooth v4.0 single mode) module with a U.FL antenna connector, operating in the 2.4 GHz ISM band at data rates up to 2 Mbps from a 2 V to 3.6 V supply on a 32-pin SMD module footprint. It is the external-antenna variant of the Bluegiga BLE112 family, targeted at low-power sensors and wireless accessories. A Bluetooth Low Energy module is a complete wireless subsystem that integrates a BLE radio, a microcontroller, an antenna or antenna connector, and a certified protocol stack into a single surface-mount package. Within the wireless hierarchy, it sits below full Bluetooth systems and above bare radio chips, allowing designers to add BLE connectivity without developing RF layout, antenna matching, or regulatory certification themselves. Key features include Bluetooth v4.0 single-mode compliance, support for both master and slave roles with 4 or more simultaneous connections in master mode, and an integrated Bluetooth Low Energy stack covering GAP, GATT, L2CAP, SMP, and BLE profiles. The fully integrated approach combines radio, microcontroller, and software stack in one certified module, dramatically reducing development effort. Technically, the module integrates the BLE radio transceiver with an on-board microcontroller running the Bluegiga Bluetooth Smart software, so host processors can communicate over a simple interface or the application can run entirely on-module. The U.FL connector permits an external antenna for optimized range and enclosure flexibility, distinguishing the -V1C variant from the chip-antenna BLE112-A-V1. Typical applications include battery-powered sensor nodes, proximity beacons, fitness and health accessories, and industrial wireless monitoring where a Class 2 link with an externally optimized antenna is preferred. The 2 V to 3.6 V supply range allows direct operation from a coin-cell battery. Design consideration: the U.FL variant requires a mating antenna assembly (U.FL to SMA pigtail plus antenna) in the bill of materials, and the 50-ohm transmission line to the connector should follow controlled-impedance layout practice on the host PCB. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
BLE112-E-V1 - Bluetooth 4.0 BLE Module U.FL | Silicon Labs
BLE112-E-V1

BLE112-E-V1 - Bluetooth 4.0 BLE Module U.FL | Silicon Labs

The Silicon Labs BLE112-E-V1 is a Bluetooth v4.0 single-mode Bluetooth Low Energy (BLE) transceiver module operating in the 2.4 GHz ISM band, offering 2 Mbps over-the-air data rate, -91 dBm receiver sensitivity, and a supply voltage range of 2.0 V to 3.6 V. The E-version variant features a U.FL RF connector for an external antenna, in a surface-mount module package, and is classified as a Bluetooth Class 2 device. A Bluetooth Low Energy module is an integrated wireless subsystem that combines a 2.4 GHz radio transceiver, a microcontroller, an antenna feed, and a complete BLE software stack on a pre-certified printed circuit assembly. Within the wireless connectivity hierarchy, it sits below full custom radio designs (lower integration effort) and above bare wireless MCUs (higher ease of use), making BLE modules the fastest route to adding short-range, ultra-low-power connectivity to a product. Key features of the BLE112-E-V1 include full Bluetooth 4.0 single-mode compliance, an integrated radio, microcontroller and software stack in one package, an 18-source interrupt controller, and support for power modes 1 and 2 in which the sleep timer keeps running to minimize average current draw. The module is targeted specifically at low-power sensors and accessories where battery life, not throughput, is the primary design constraint. Technically, the module is built around the CC2540 Bluetooth SoC, which pairs an industry-standard 8051 core with a 2.4 GHz RF transceiver. Peripheral peripherals can choose between two alternate I/O pin locations for layout flexibility, and an ultra-low-power sleep timer uses an external 32.768 kHz crystal oscillator. Receiver sensitivity of -91 dBm provides practical indoor range for a Class 2 device, while the 2 Mbps PHY minimizes radio-on time. Typical applications include battery-powered sensor nodes and beacons, wireless health and fitness accessories, smart-home sensor peripherals, and RS232-over-BLE cable replacement links in industrial equipment. When designing with the BLE112-E-V1, plan the power budget around sleep modes and remember that the E variant requires an external antenna connected via the U.FL receptacle; the -A variant integrates the antenna on the PCB instead. Supply rails must stay within 2.0 V to 3.6 V, ideally from a primary lithium or single Li-Ion cell. This page synthesizes verified distributor pricing, drop-in same-family alternatives, and practical design guidance not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
BLE113-A-M256K - Bluetooth 4.0 BLE Module 256K Flash | Silicon Labs
BLE113-A-M256K

BLE113-A-M256K - Bluetooth 4.0 BLE Module 256K Flash | Silicon Labs

The Silicon Labs BLE113-A-M256K is a Bluetooth Smart (Bluetooth v4.0 low energy) transceiver module operating at 2.4 GHz with an integrated chip antenna, 256 KB flash memory, a supply range of 2.0 V to 3.6 V, 2 Mbps over-the-air data rate, and -93 dBm receiver sensitivity. It is a fully integrated Bluetooth Smart solution combining the radio, a microcontroller, and the Bluetooth software stack in a single surface-mount module. A Bluetooth Low Energy (BLE) module is a complete wireless subsystem within the broader hierarchy of RF transceiver modules and short-range wireless communication devices. Whereas a bare radio chip requires the designer to integrate a microcontroller, antenna matching network, and protocol stack, a BLE module such as the BLE113 integrates all features required for a Bluetooth smart application: the Bluetooth radio, antenna, MCU, and certified stack, reducing time to market and RF design risk. Key features include the 256 KB flash variant (versus 128 KB on BLE113-A-V1), which is significant for over-the-air (OTA) firmware updates and extensive BGScript applications, integrated chip antenna eliminating external RF matching design, and low power operation targeted at small sensors and accessories. Serial interfaces include ISP, PWM, SPI, and UART, allowing flexible host connectivity or fully standalone operation via BGSCRIPT. Technically, the module is built around the Texas Instruments CC2541 utilized IC and belongs to the Bluegiga BLE113 family acquired by Silicon Labs. The -93 dBm sensitivity supports reliable connections at Class 2 power levels on the 2.4 GHz ISM band, and the integrated antenna means the RF performance is pre-certified, saving regulatory test cost. Typical applications include low-power sensors and accessories, battery-powered health and fitness devices, beacons, smart home endpoints, and industrial wireless sensor nodes where a compact, certified BLE link is required. A key design consideration is supply voltage: the module accepts only 2.0 V to 3.6 V, so a single CR2032 coin cell or a regulated LiPo rail works well, but 5 V systems require an LDO. Allow antenna keep-out clearance on the PCB around the chip antenna region. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
BLE113-A-V1 - Bluetooth 4.0 BLE Module, 2V-3.6V | Silicon Labs
BLE113-A-V1

BLE113-A-V1 - Bluetooth 4.0 BLE Module, 2V-3.6V | Silicon Labs

The Silicon Labs BLE113-A-V1 is a Bluetooth Smart (Bluetooth 4.0 low energy) transceiver module operating in the 2.4 GHz ISM band from a 2.0 V to 3.6 V supply, with a receive sensitivity of -93 dBm and an integrated chip antenna in a compact 28-pad surface-mount castellated package. Originally developed by Bluegiga Technologies, later acquired by Silicon Labs, it targets small, low-power sensors and accessories. A Bluetooth Low Energy (BLE) module is a complete short-range wireless subsystem that integrates the 2.4 GHz radio transceiver, a microcontroller, the BLE software stack, and an antenna into a single certified unit. Within the connectivity hierarchy (module -> BLE radio -> 2.4 GHz transceiver -> RF IC -> semiconductor), modules eliminate the RF design, regulatory certification, and stack porting work otherwise required of a discrete chip design. Key features of the BLE113 include a fully integrated Bluetooth radio, microcontroller, and GATT-based software stack; the ability to host the end-user application on-module via the BGSCRIPT scripting language or BLE API, so no external MCU is needed in size- or price-constrained devices; serial interfaces including UART, SPI, PWM, and ISP for system integration; and very low power consumption for battery-powered designs (active-mode current is roughly 6 mA per Silicon Labs community measurements on comparable firmware). Architecturally, the module is built around the Texas Instruments CC2541 BLE system-on-chip running the Bluegiga iWRAP-based Bluetooth Smart stack. The GATT profile server and client, security manager, and OTA-capable firmware structure are all resident on-module, exposing a simple UART API or BGSCRIPT environment to the host. Typical applications include battery-powered IoT sensors, fitness and health accessories, smart tags and beacons, and industrial wireless sensor nodes - anywhere a certified Bluetooth Smart link must be added without RF expertise. The integrated chip antenna keeps the BOM minimal and removes antenna tuning from the design cycle. A key design consideration: the BLE113-A-V1 variant contains only 128 kB of flash. If you plan over-the-air firmware updates or a large BGSCRIPT application, the pin-compatible BLE113-A-M256K with 256 kB flash is the better choice within the same footprint. This page synthesizes distributor pricing, drop-in alternatives, practical design notes, and migration guidance from Silicon Labs application note AN1036 - information not consolidated in the manufacturer datasheet alone.

RFQ پەیوەندی
BLE113-A-V1C - Bluetooth 4.0 Smart Module, 2V-3.6V | Silicon Labs
BLE113-A-V1C

BLE113-A-V1C - Bluetooth 4.0 Smart Module, 2V-3.6V | Silicon Labs

The Silicon Labs BLE113-A-V1C is a Bluetooth Smart (Bluetooth v4.0 low energy) Class 2 module targeted at small, low-power sensors and accessories, operating from a 2V to 3.6V supply with 2Mbps over-the-air data rate on a 36-pin SMD land pattern with an integrated chip antenna. A Bluetooth Smart module is a complete wireless subsystem that integrates the 2.4GHz Bluetooth radio, a microcontroller, the BLE software stack, and GATT-based profiles into a single certified unit. Within the system hierarchy, it sits between a discrete BLE chipset design (radio IC plus external host MCU plus software) and a full system-on-chip; modules such as the BLE113 fall into the broader categories of RF module, transceiver module, and wireless connectivity IC. Key features include full integration of radio, MCU (8051-based, running the Bluegiga Bluetooth Smart stack), and antenna, which removes RF layout effort and regulatory certification burden. Supply operation from 2V to 3.6V allows direct powering from a 3V coin cell. The module can host end-user applications via BGScript or the BGAPI serial protocol, meaning many designs need no external microcontroller at all - a significant saving in size, BOM cost, and power. Architecturally, the BLE113 combines a Bluetooth radio with an integrated MCU executing the Bluetooth low energy protocol stack and GATT profiles. The V1C variant carries the standard flash configuration of the BLE113 family (128kB flash; the A-M256K variant offers 256kB for OTA updates and larger BGScript applications). Typical applications include battery-powered sensor nodes, proximity and iBeacon-style beacons, wearable accessories, smart-home devices, and small medical/health peripherals where compact size and low average current dominate. Design consideration: because the V1C uses an internal chip antenna, keep clearance around the antenna area per the Bluegiga layout guidelines; the A-V1 variant (external antenna connection) is the choice when metal or enclosure constraints demand an external antenna. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
BLED112-V1 - Bluetooth 4.0 BLE USB Dongle | Silicon Labs
BLED112-V1

BLED112-V1 - Bluetooth 4.0 BLE USB Dongle | Silicon Labs

The Silicon Labs BLED112-V1 is a single-mode Bluetooth Low Energy (Bluetooth 4.0) USB dongle operating in the 2.402 GHz to 2.48 GHz ISM band at 1 Mbps, with -91 dBm receiver sensitivity and approximately 30 m range, housed in a USB Type-A dongle form factor powered from a 3.6 V to 5.5 V USB supply. A BLE USB dongle is a complete wireless connectivity module that integrates the Bluetooth radio, a microcontroller running the BLE protocol stack, and an antenna into a USB stick. In the connectivity hierarchy it sits at the module level: Bluetooth 4.0 single-mode device (BLE only), implemented as a network co-processor controlled by an external host over USB. Unlike standard Bluetooth dongles that rely on the operating system Bluetooth stack, the BLED112 exposes the full BLE controller and GAP/GATT functionality to the application. Key features include full BLE 4.0 single-mode operation, the Bluegiga BGAPI serial protocol that lets any external host (PC, MCU, LabVIEW) control the stack over USB, the BGScript scripting language for standalone operation, and the Bluegiga Profile Toolkit for rapid custom GATT profile prototyping. The integrated antenna removes RF design effort, and -91 dBm sensitivity supports robust links up to roughly 30 m in line-of-sight conditions. Architecturally, the BLED112 embeds Silicon Labs (Bluegiga) BLE silicon with on-board flash running the Bluetooth stack, so the host only needs to send BGAPI commands over the USB CDC interface. This bypasses the limitations of native Windows, macOS, and Linux BLE stacks, giving applications full control over GATT communication and BLE advertisements - a key reason it is widely used in test fixtures and instrumentation. Typical applications include adding BLE connectivity to PCs and embedded hosts for sensor data acquisition, BLE development and profiling with two dongles, LabVIEW-based BLE test systems, and robotics and IoT gateway links. Design consideration: because the part is end-of-life, plan a migration path early; the BGAPI protocol is shared across the Silicon Labs BLE module family, which eases firmware-level porting even though a mechanical USB-dongle drop-in is scarce. This page synthesizes distributor availability data, BGAPI ecosystem information, drop-in replacement analysis, and practical design notes not found together in the manufacturer datasheet.

RFQ پەیوەندی
BLED112-V1C - Bluetooth 4.0 Low Energy USB Dongle | Silicon Labs
BLED112-V1C

BLED112-V1C - Bluetooth 4.0 Low Energy USB Dongle | Silicon Labs

The Silicon Labs BLED112-V1C is a Bluetooth v4.0 Low Energy (BLE) USB dongle transceiver module operating in the 2.402 GHz to 2.48 GHz band with integrated antenna, -91 dBm receiver sensitivity, and up to 30 m range, powered from a 3.6 V to 5.5 V supply over USB. A BLE dongle is a finished, fully certified Bluetooth Low Energy radio unit in a USB stick form factor. Unlike bare RF modules that require antenna design and regulatory testing, a dongle integrates the radio, microcontroller, BLE stack, and antenna, and plugs directly into a host USB port. In the connectivity hierarchy it sits under: Bluetooth module -> short-range wireless transceiver -> RF transceiver finished unit -> wireless communication device. Key features include Bluetooth v4.0 single-mode low energy operation at 1 Mbps, a UART serial interface alongside native USB, support for the Bluegiga BGAPI binary protocol and BGScript scripting, and R&TTE Directive (1999/5/EC) conformity with Anatel certification (06875-18-03402) for Brazil. These attributes allow hosts without native BLE to gain BLE connectivity with zero RF design effort. Architecturally, the BLED112 combines an integrated Bluetooth radio, microcontroller, and pre-flashed software stack. Application logic can run on-board using the Bluegiga Profile Toolkit and BGScript, or the host can drive the module over BGAPI, offloading the entire BLE stack from the host CPU. This makes it a favorite in PC-based instrumentation and test setups. Typical applications include adding BLE to lab equipment and data loggers, Linux, Android, and Windows host connectivity for BLE sensors, BLE profile prototyping using two dongles, and industrial wireless configuration tools. The 30 m range and integrated trace antenna suit desktop and benchtop use. Design consideration: because the dongle is a finished USB unit, the main integration risk is host driver and BGAPI software compatibility rather than RF layout; plan software migration early since the family is nearing end-of-life. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
BLUENRG-M0A - BLE v4.2 Module, -85dBm, 2.4GHz | STMicroelectronics
BLUENRG-M0A

BLUENRG-M0A - BLE v4.2 Module, -85dBm, 2.4GHz | STMicroelectronics

The STMicroelectronics BLUENRG-M0A is a very low-power Bluetooth Low Energy (BLE) v4.2 network processor module built around the BlueNRG-MS SoC, housed in an integrated surface-mount chip antenna package. The module operates across the 2.4 GHz to 2.4835 GHz ISM band and delivers up to +8 dBm transmit power with -85 dBm receiver sensitivity, providing robust link margins for typical IoT indoor and outdoor deployments. It supports Bluetooth SIG end-product certification with pre-certifications across major world regions, dramatically reducing time-to-market for connected products. A Bluetooth Low Energy (BLE) module is a self-contained radio subsystem that integrates the transceiver IC, crystal, antenna, and matching network into a single surface-mount unit, allowing designers to add wireless connectivity without RF layout expertise. Within the connectivity hierarchy, BLE sits below Wi-Fi in data rate (typically 1 Mbps) but offers much lower power consumption (peak currents in the single-digit milliamp range), making it the preferred choice for coin-cell and energy-harvesting IoT devices. The BLE module category itself bridges wireless transceiver ICs and complete wireless modules. Key specifications include 20 mA peak transmit current, ultra-low sleep current, SPI host interface (up to 8 MHz), and an integrated 32 MHz crystal. The module supports master and slave roles simultaneously and operates from -40 °C to +85 °C. According to the BlueNRG-M0 modules flyer, the BLUENRG-M0A is pin-compatible with the BLUENRG-M0L ceramic antenna variant, enabling designers to migrate between antenna types on the same PCB footprint. The BlueNRG-MS die inside the module uses a Cortex-M0 core architecture with embedded Bluetooth protocol stack, offloading all link-layer and host-stack processing from the external host MCU. This network-processor approach minimizes host-side firmware complexity while preserving full BLE v4.2 feature coverage, including LE Privacy 1.2, LE Data Length Extension, and up to eight simultaneous connections. Typical applications include wearable fitness bands, BLE beacons (iBeacon and Eddystone), industrial sensor nodes, smart home bridges, medical monitoring patches, and remote control units. The combination of pre-certified module-level compliance and ultra-low power makes it particularly suitable for battery-powered products targeting FCC, CE, IC, TELEC, and KCC regulatory domains. When designing with the BLUENRG-M0A, route the host SPI bus with short traces and 50 Ω-controlled impedance where possible, and place at least 5 mm of clearance around the chip antenna area to avoid ground-plane detuning. Decoupling VDDL with a 100 nF ceramic capacitor placed within 3 mm of the pin ensures stable operation across load transients. This page synthesizes distributor pricing, drop-in compatible alternatives across the BlueNRG module family, and practical RF design notes not found in the standalone datasheet - including a parameter-by-parameter comparison against the M0L, M2SA, and M2SP variants.

RFQ پەیوەندی
BLUENRG-M0L - Bluetooth v4.2 LE Module 2.4GHz | STMicroelectronics
BLUENRG-M0L

BLUENRG-M0L - Bluetooth v4.2 LE Module 2.4GHz | STMicroelectronics

The STMicroelectronics BLUENRG-M0L is a Bluetooth v4.2 compliant, very low-power network processor module that operates in the 2.4 GHz to 2.4835 GHz ISM band. It is a surface-mount integrated chip antenna module that combines an embedded Bluetooth low-energy protocol stack with master/slave role support and simultaneous multiple-role operation, enabling concurrent sensor and hub functions on the same module. A Bluetooth Low Energy (BLE) module is a certified sub-system that bundles the radio transceiver, baseband, protocol firmware, and often an integrated antenna into a single reflow-solderable package. Within the wireless connectivity hierarchy, BLE modules sit below bare SoCs and above discrete 2.4 GHz radios: they trade flexibility for faster time-to-market because the wireless regulatory certification and stack integration are already completed by the module vendor. The BlueNRG-M0 family targets ultra-low-power IoT nodes where battery life, footprint and BOM count matter more than raw compute. Key features include Bluetooth v4.2 master/slave support, multi-role operation, an integrated chip antenna, surface-mount packaging in an 11-SMD module form factor, and an output power of 6 dBm. The BLUENRG-M0L variant differs from the BLUENRG-M0 in its regulatory certifications and is built around the BlueNRG-MS silicon. Sensitivity is rated at -85 dBm, receive current is 16.36 mA, and transmit current is 13.25 mA to 27.35 mA depending on output power setting. Architecturally, the BLUENRG-M0L is built around a low-power Cortex-M0 core running ST's embedded Bluetooth low-energy stack. The integrated chip antenna, RF matching network, crystals, and passive components are pre-tuned inside the module, so the host MCU only communicates with it over a UART/SPI host interface. This removes the need for 50-ohm RF layout expertise and saves several weeks of PCB iteration. Typical applications include BLE sensor nodes, beacons, smart-home hubs, fitness and medical wearables, industrial telemetry, and remote controls. The -40C to +85C operating range makes it usable in outdoor and industrial deployments. Because the regulatory certification is pre-done, designers can skip the FCC/CE/IC RF certification cycle and ship products faster. When designing with the BLUENRG-M0L, leave the antenna keep-out area clear of copper on all PCB layers and avoid placing metal components or shields above the antenna. Provide a stable 1.7 V to 3.6 V supply and place a 1 uF decoupling capacitor close to the module's VDD pin. The host MCU must drive the module via the documented ACI (Application Command Interface) over SPI or UART; firmware updates go through the bootloader. This page synthesizes distributor pricing, package-level drop-in variants, and practical design notes for fast time-to-market BLE designs that go beyond what the ST datasheet flyer alone provides.

RFQ پەیوەندی
BM71BLES1FC2-0004AA - BLE 5.0 Module, 9x11.5mm | Microchip
BM71BLES1FC2-0004AA

BM71BLES1FC2-0004AA - BLE 5.0 Module, 9x11.5mm | Microchip

The Microchip Technology BM71BLES1FC2-0004AA is a fully certified Bluetooth 5.0 Low Energy (BLE) transceiver module operating in the 2.4 GHz ISM band, housed in a shielded 16-SMD surface-mount package measuring 9 x 11.5 x 2.1 mm with an integrated chip antenna. The module supports industrial operating temperature range of -40C to +85C. A Bluetooth Low Energy (BLE) module is a type of short-range RF module that integrates a Bluetooth radio, baseband controller, and protocol stack into a single shielded unit. Within the wireless hierarchy, it sits between discrete RF transceiver chips and fully qualified end products, allowing OEMs to skip costly Bluetooth SIG qualification and RF tuning. BLE, also called Bluetooth Smart, is the low-power variant of the Bluetooth 802.15.1 standard optimized for battery-powered devices. Key features of the BM71 family include Bluetooth 5.0 compliance delivering up to 2.5x throughput improvement over Bluetooth 4.1 based designs, more secure connections, an on-board chip antenna requiring no external RF matching, and full shielding for coexistence with other radios. The embedded firmware implements the complete BLE stack, so the host MCU only needs a simple UART interface. Technically, the BM71 uses Microchip's certified radio with an embedded protocol stack, offloading advertising, connection management, GATT services, and security pairing from the host processor. Configuration is performed via simple ASCII or transparent UART commands, reducing firmware complexity and certification burden. Typical applications include IoT sensor nodes, smart home devices, battery-powered beacons, industrial wireless sensors, and connected medical accessories, where the module's low power sleep modes and small 9 x 11.5 mm footprint fit space- and energy-constrained designs. Design consideration: keep the module antenna region clear of ground planes and metal per Microchip's layout guidelines, and power the module from a clean 3.3V rail with local decoupling. This page synthesizes distributor availability, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
BM71BLES1FC2-0B02AA - BLE 5.0 Module 9x11.5mm | Microchip
BM71BLES1FC2-0B02AA

BM71BLES1FC2-0B02AA - BLE 5.0 Module 9x11.5mm | Microchip

The Microchip Technology BM71BLES1FC2-0B02AA is a fully certified Bluetooth 5.0 Low Energy (BLE) transceiver module operating in the 2.4 GHz ISM band, housed in a shielded 9 x 11.5 x 2.1 mm surface-mount package with an integrated chip antenna and -90 dBm receiver sensitivity. A Bluetooth Low Energy module is a complete wireless subsystem that integrates a BLE radio, baseband, protocol stack, and antenna into a single certified unit. In the system hierarchy it sits above discrete RF ICs (which require external stack development and RF design) and below complete host systems, functioning as a serial-to-BLE bridge that frees the host MCU from managing the Bluetooth software stack, timing-critical RF firmware, and regulatory certification. Key features of the BM71BLES1FC2-0B02AA include Bluetooth Core 5.0 compliance with up to 2.5x throughput improvement over earlier BM70-generation silicon, a completely integrated Bluetooth software stack with configuration via simple ASCII commands over UART, a shielded enclosure for EMI reduction, and an integrated chip antenna on a regulatory-certified variant. Supply voltage spans 1.9 V to 3.6 V, suiting single-cell lithium and 3.3 V logic designs, and the module is rated for industrial temperature environments. Architecturally, the BM71 embeds Microchip's BLE silicon with flash memory for stack and application script storage. The certified, shielded, antenna-integrated construction means the RF matching network, crystal, and antenna have been tuned by Microchip, removing the most error-prone portion of a wireless design. Developers interact with the module as a wireline replacement: UART data in, BLE data out. Typical applications include smart-home sensors and actuators, battery-powered IoT beacons, industrial wireless configuration and diagnostic links, and connected health accessories. The industrial temperature rating and shielded package also suit networked lighting controls and commercial building automation. A key design consideration is layout: although the antenna is integrated, keep at least the datasheet-recommended keep-out area free of copper and plastics above the antenna region to preserve the certified radiation pattern and sensitivity. This page synthesizes distributor pricing (as of 2026-10-19), drop-in family alternatives, design notes, and long-tail selection guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
BM83SM1-00AB Bluetooth 5.0 Stereo Audio Module | Microchip
BM83SM1-00AB

BM83SM1-00AB Bluetooth 5.0 Stereo Audio Module | Microchip

The Microchip Technology BM83SM1-00AB is a Bluetooth 5.0 stereo-audio transceiver module operating from 2.402 GHz to 2.48 GHz in a PCB-trace, surface-mount package. It supports Bluetooth Classic BR/EDR and Bluetooth Low Energy, together with HFP 1.7, HSP 1.2, A2DP 1.3, SPP 1.2, AVRCP 1.6, PBAP 1.2, GATT, and GAP. The module can receive audio through Auxiliary Input or I2S and stream it to as many as two paired Bluetooth sink devices using Audio Transceiver firmware. A Bluetooth audio module combines a short-range radio, baseband protocol stack, audio interface, and embedded control functions in one surface-mount assembly. The BM83 belongs to the RF transceiver-module hierarchy rather than a discrete Bluetooth IC: designers connect the module to a host product through power, control, communication, and audio interfaces instead of implementing an RF antenna network and Bluetooth firmware from scratch. Its Class 1 designation identifies it as a Bluetooth audio module intended for conventional short-range wireless audio links. The BM83SM1-00Tx configuration provides A2DP source capability, allowing legacy audio equipment to become a Bluetooth transmitter. A2DP Source and Sink support supports product designs that transmit or receive stereo audio. HSP 1.2 supports legacy headset roles, while HFP 1.7, PBAP 1.2, AVRCP 1.6, and SPP 1.2 address hands-free calling, phone-book access, media control, and serial data services. AAC and SBC decoding further broadens compatibility with common Bluetooth audio sources. The module integrates the radio and protocol functions required for embedded Bluetooth connectivity, reducing RF-layout exposure at the product level. Nevertheless, an embedded module does not eliminate antenna-design requirements: the PCB, copper, enclosure, ground distribution, and matching network still determine practical RF performance. Firmware selection and host-interface integration are equally important because protocol support alone does not establish the final user experience. Typical uses include Bluetooth audio dongles, wireless speakers, headphones, soundbars, automotive-accessory adapters, home-audio upgrades, and dual-sink speaker systems. Auxiliary Input suits products with an existing analog source, while I2S supports digital audio integration. The stated ability to stream to two paired sink devices is particularly useful when one product must share audio with two headphones or speakers. For implementation, follow the manufacturer datasheet for the exact 50-lead land pattern, exposed-pad or thermal requirements, supply sequencing, UART or control behavior, firmware configuration, and antenna clearance. Preserve the documented keep-out regions around the module and connect its RF reference and ground features exactly as specified. Do not assume that another BM83 suffix is interchangeable without checking revision, antenna, firmware, and regulatory differences.

RFQ پەیوەندی
BM83SM1-00TA Bluetooth 5.0 Stereo Audio Module | Microchip
BM83SM1-00TA

BM83SM1-00TA Bluetooth 5.0 Stereo Audio Module | Microchip

The Microchip Technology BM83SM1-00TA is a Bluetooth 5.0 stereo audio module operating across 2.402 GHz to 2.48 GHz in a 50-lead surface-mount package. It combines Bluetooth Classic BR/EDR and Bluetooth Low Energy connectivity with integrated audio-transceiver firmware. According to the verified Microchip product material, the module supports HFP 1.7, HSP 1.2, A2DP 1.3, SPP 1.2, AVRCP 1.6, and PBAP 1.2, including A2DP source and sink operation. A Bluetooth audio module is a wireless connectivity and embedded-control subsystem that adds Bluetooth communication to an audio product without requiring a discrete radio design. In the broader product hierarchy, this module is a Bluetooth transceiver module, an RF and wireless module, and an embedded audio bridge. It can receive audio through auxiliary input or I2S and stream that audio to up to two paired Bluetooth sink devices, making it useful for dongle-style designs and products without native Bluetooth. The BM83SM1-00TA is qualified for Bluetooth 5.0 and supports Classic BR/EDR as well as BLE. Its profile set covers hands-free, headset, advanced audio distribution, serial port, audio/video remote control, and phone-book access functions. A2DP source and sink capability supports both sending audio to headphones or speakers and receiving audio from a paired source. The module also supports AAC and SBC decoding, broad protocol support, and GATT/GAP services. The BM83 family is intended for stereo-audio connectivity in compact embedded products. Its integrated module approach reduces the need to design and qualify a separate RF radio, antenna structure, audio interface, and Bluetooth protocol stack on the host PCB. Firmware configuration remains important: the BM83SM1-00Tx variant implements A2DP source capability using Audio Transceiver firmware, so host firmware and command sequences must match the intended audio role. Typical uses include Bluetooth audio dongles, wireless speakers, headphones, source accessories, home-audio adapters, and embedded audio gateways. The verified data confirms the frequency range, Bluetooth version, protocol profiles, audio inputs, and dual-sink streaming behavior. Electrical limits, pin names, supply voltage, antenna requirements, and package dimensions should be taken from the manufacturer datasheet before PCB release. PCB implementation must preserve the module’s required antenna clearance, ground connectivity, audio routing, and power decoupling. Keep RF-sensitive and audio-sensitive traces away from noisy switching paths where practical, provide the manufacturer-specified bypass capacitors close to the supply pins, and follow the reference layout for antenna and exposed grounding. Validate RF performance with the intended enclosure because plastic, cables, grounding, and nearby structures can change the installed antenna behavior. This product-data page combines the verified Microchip feature description, distributor identification, and cross-reference search results. It distinguishes confirmed facts from missing electrical details and avoids inventing a pinout or package drawing that was not present in the supplied sources. For production use, compare the selected BM83SM1 variant, firmware image, regulatory requirements, and supplier availability before committing the design.

RFQ پەیوەندی
BMD-341-A-R - BLE 5.0/Thread/Zigbee Module | u-blox
BMD-341-A-R

BMD-341-A-R - BLE 5.0/Thread/Zigbee Module | u-blox

The u-blox BMD-341-A-R is a stand-alone Bluetooth 5.0 Low Energy, Thread, and Zigbee (IEEE 802.15.4) multiprotocol transceiver module operating in the 2.4 GHz band, based on the Nordic Semiconductor nRF52840 SoC with an ARM Cortex-M4F CPU, supplied in a 10.2 x 15.2 mm surface-mount package with a U.FL connector for an external antenna (antenna not included). A Bluetooth Low Energy (BLE) module is a short-range radio subsystem that integrates the radio, modem, processor, crystal, and RF matching network into a certified, pre-tested unit. Modules sit above raw SoCs in the wireless hierarchy, reducing RF design effort, certification cost, and time to market for connected products. Key features include full Bluetooth 5.0 long-range support, 802.15.4 Thread and Zigbee protocols, and an open CPU architecture that lets developers run their own firmware on the embedded nRF52840 with 1 MB flash and 256 KB RAM. The U.FL connector enables optimized external antennas for maximum range. The module is certified for use in Canada under ISED RSS-247 Issue 2 and RSS-Gen per the u-blox datasheet, and its footprint is identical to the BMD-340, with pins 1 through 47 directly mapping to BMD-300/301/330/360 for design reuse. Typical applications include low-power IoT sensor nodes, smart-home Thread/Zigbee devices, beacons, and connected industrial equipment. Design consideration: when one PCB design may use BMD-340, BMD-341, or BMD-345, follow the BMD-340 copper keep-out area for the trace antenna variant. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and design notes not found in the manufacturer datasheet.

RFQ پەیوەندی