ADS774KE - 12-Bit 125 kSPS SAR ADC | Texas Instruments
MPN: ADS774KE ✗ کۆتایی ژیانADS774KE گشتی
An ADC is a data-converter IC that converts an analog input voltage into a digital value for processing by a microprocessor, microcontroller, programmable logic controller, or digital signal processor. Successive-approximation converters repeatedly compare the input voltage with an internally generated DAC until the residual falls below one least-significant-bit threshold. The ADS774 combines that conversion technique with an internal sampling network, reference, clock, and microprocessor interface to form a complete sampling ADC.
The primary characteristics of the ADS774KE are 12-bit resolution, one analog input channel, an 8.5 us maximum conversion time over the specified temperature range, and operation from a single +5 V supply. Its maximum sampling frequency is identified as 125 kSPS, while the product listing also describes approximately 117 kHz sampling. The parallel digital interface allows the converter to transfer each 12-bit result directly into a microprocessor or other parallel data bus.
The internal capacitor-array CDAC implements the successive-approximation conversion function in low-power CMOS. Because sampling is integrated into the converter, most designs do not require a separate sample-and-hold amplifier. The complete converter function, including its reference and clock, reduces external circuit complexity, although the input source still needs to satisfy the acquisition, impedance, settling-time, and bypass-capacitance requirements described by Texas Instruments.
ADS774KE is applicable in process monitoring, industrial sensor interfaces, laboratory measurement equipment, digital panel meters, factory-control systems, and legacy microprocessor data-acquisition cards. It is particularly relevant when an existing parallel-bus system needs a complete 12-bit conversion function and the added integration of the ADS774 reduces the component count compared with a discrete sample-and-hold, reference, converter, and interface arrangement.
Designers should pay close attention to analog grounding, input-source impedance, reference behavior, and the acquisition interval available before each conversion. Place the bypass capacitors specified in the manufacturer datasheet close to their associated supply pins, and route analog input traces away from digital clock and interface lines. Confirm timing against the host processor because the ADS774 requires control signals and data acquisition to be coordinated within its conversion sequence.
This page combines the manufacturer function description with package, resolution, interface, application, and replacement guidance. It also separates verified drop-in choices from older converter families so engineers can assess board-level compatibility before committing to a replacement.
جێگرەوەکانی جێگۆڕکێ بۆ ADS774KE — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADS774KE (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Architecture, Clock, Input Type, Reference.
ADS774JEG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADS774JEG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADS774KE زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| ADC Type | Successive-approximation ADC |
| وردی | 12 bit |
| Input Channels | 1 channel |
| Maximum Conversion Time | 8.5 us over temperature |
| Maximum Sampling Rate | 125 kSPS |
| Architecture | Capacitor array CDAC |
| Process Technology | Low-power CMOS |
| ڤۆڵتیەی دابینکردن | +5 V |
| Input Type | Single-ended analog input |
| Digital Interface | Microprocessor-compatible parallel interface |
| Sampling Circuit | Internal sampling; eliminates external sample-and-hold in most applications |
| Reference | Internal reference |
| Clock | Internal clock |
| پاکێج | 28-pin PDIP |
| جۆری دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی ADS774KE 28-pin pdip
ڕێکخستنی پین بۆ ADS774KE (پاکێجی 28-pin pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADS774KE.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADS774KE گونجاوە بۆ 6 بەکارھێنانs: Industrial Process Monitoring, Digital Panel Meter, Laboratory Instrumentation, Factory Control System, Legacy Data-Acquisition Card, Embedded Sensor Interface.
Industrial Process Monitoring
ADS774KE fits industrial process-monitoring equipment that must convert a sensor or conditioned process signal into a 12-bit value for a controller or host processor. Its single-channel SAR architecture, internal sampling function, integrated reference, internal clock, and single +5 V supply reduce the number of separate analog components required around the converter. The 8.5 us maximum conversion time supports acquisition rates up to the stated 125 kSPS, although actual cycle time depends on control-signal sequencing and the available acquisition interval. Use a properly buffered or high-impedance source and follow the Texas Instruments grounding and bypass recommendations to preserve measurement stability.
پێشنیارکراو
Digital Panel Meter
ADS774KE is appropriate for a digital panel meter that measures one analog quantity and presents the result through a parallel microprocessor interface. The complete sampling converter integrates the reference, clock, and sample-and-hold function, which can simplify a compact meter design compared with a discrete converter chain. Its 12-bit resolution provides 4096 digital codes for the selected analog range, while the 8.5 us maximum conversion time is far shorter than the update interval of most human-readable displays. Front-end scaling, input protection, calibration, and display update timing remain outside the ADC and should be designed around the manufacturer's electrical characteristics.
پێشنیارکراو
Laboratory Instrumentation
ADS774KE can serve as the measurement converter in laboratory instrumentation built around a legacy parallel-bus controller. The microprocessor-compatible output allows a 12-bit result to be read without adding a serial-interface protocol, and the integrated sampling, reference, and clock functions simplify analog acquisition. The device's 8.5 us maximum conversion time supports fast measurements, but instrument accuracy also depends on the reference accuracy, input noise, source impedance, calibration method, and analog layout. Use short input paths, appropriate bypass capacitors, and careful grounding to prevent external noise from limiting the converter's 12-bit measurement capability.
پێشنیارکراو
Factory Control System
ADS774KE is suitable for a factory-control subsystem that samples one conditioned analog channel and transfers the converted value to a microprocessor-based controller. Its single +5 V supply, 12-bit resolution, and integrated sampling, reference, and clock functions support a compact acquisition stage. The 125 kSPS maximum sampling rate provides headroom for fast control loops, although software must correctly manage conversion requests, chip select, data-read strobes, and acquisition timing. Electrical isolation, surge protection, sensor excitation, and transducer conditioning normally require additional circuitry and should not be assumed to be part of the ADC.
پێشنیارکراو
Legacy Data-Acquisition Card
ADS774KE is a natural fit when maintaining or expanding a legacy parallel-bus data-acquisition card designed around 12-bit microprocessor-compatible converters. The integrated sampling function eliminates the need for a separate sample-and-hold stage in most applications, while the internal reference and clock reduce external component count. Because the package is a 28-pin PDIP, it can also support repair-oriented and prototype boards that require through-hole construction. Before replacing another converter family, verify that output coding, conversion timing, polarity, reference behavior, and every pin assignment match the original board rather than relying only on resolution and sampling rate.
پێشنیارکراو
Embedded Sensor Interface
ADS774KE can form the central conversion element of a single-channel embedded sensor interface when the conditioned sensor output falls within the ADC's supported input range. The internal sampling network, reference, clock, and +5 V operation support integration near a microprocessor or microcontroller, while 12-bit resolution supports many position, level, and condition measurements. Input conditioning remains critical because sensor output impedance, excitation, filtering, and protection can determine whether the converter receives a valid settled voltage during acquisition. Use the datasheet timing diagram to calculate the required input settling time and add local bypass capacitance close to the supply pins.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ ADS774KE — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ADS774JE | ADS774JEG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin PDIP | 28-pin PDIP | 28-pin PDIP |
| Resolution | 12 bit | 12 bit | 12 bit |
| Package Construction | 28-pin PDIP | 28-pin PDIP | Ceramic DIP |
جیاکەرەوە سەرەکییەکان
- Complete integrated sampling converter (بەراورد بەADS774JE)
- Through-hole 28-pin PDIP implementation (بەراورد بەADS774JEG4)
- Consistent 12-bit conversion performance (بەراورد بەADS774JEG4)
تێبینییەکانی دیزاین
Treat the analog input as a precision measurement node. Confirm that the driving circuit can settle to the required accuracy during the ADC acquisition interval, place the input trace away from clock and data lines, and use a compact ground return. A high-impedance sensor or long cable can require buffering because the internal sampling capacitor can draw transient charge from the source during acquisition.
Place the supply bypass capacitors close to the ADC's supply and ground pins and follow the layout shown in the manufacturer datasheet. Keep the analog input and reference-related paths physically separated from digital interface traces. In a legacy parallel system, route data and control signals consistently, keep stubs short, and account for ringing when the PCB interconnects connect the converter to a microprocessor bus.
Do not judge drop-in compatibility from resolution alone. Verify the complete pin assignment, signal polarity, output coding, conversion timing, acquisition requirements, supply limits, and operating-temperature specifications for ADS774KE and the proposed replacement. ADS774JE and ADS774JEG4 are family-level candidates documented as 28-DIP converters, but each still requires a board-level comparison before it can be approved as a substitute.
زانیاری پابەندبوون
No product-specific compliance declarations were identified. ADS774KE is an industrial data-conversion IC and is not identified as an AEC-Q100-qualified automotive device.