DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip
MPN: DSPIC30F6013AT-30I/PF ✓ چالاکDSPIC30F6013AT-30I/PF گشتی
A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a traditional MCU control core with a single-cycle DSP MAC engine on a single die. In the device taxonomy, this places the DSPIC30F6013AT-30I/PF in the hierarchy: DSC -> DSP/MCU hybrid -> 16-bit microcontroller -> embedded MCU. This category is purpose-built for real-time closed-loop control and high-bandwidth signal processing, where general-purpose MCUs lack DSP throughput and stand-alone DSPs lack peripheral integration.
Key features include 30 MIPS performance from a 30 MHz oscillator, a 12-bit ADC with up to 16 channels, two UART/SPI/I2C modules, two CAN modules, and two 16-bit timer/counters. The device also provides 60 digital I/O lines, PWM modules with dedicated time bases, and an on-chip Flash self-programming bootloader. The wide 4.5 V to 5.5 V supply range simplifies integration into 5 V analog signal chains.
The DSP engine provides a single-cycle 16-bit x 16-bit MAC plus a 40-bit accumulator with dual operand fetch-back, enabling efficient FIR/IIR filtering, FFT butterfly computations, and closed-loop control loops. The modified Harvard architecture keeps program and data memory on separate buses, removing fetch bottlenecks that throttle von Neumann MCUs during DSP workloads.
Typical applications include sensor-less BLDC/PMSM motor drives, automotive sensor fusion (with two CAN interfaces), industrial UPS and inverter control, and high-performance audio codecs with parametric equalization. The 80-pin TQFP and 5 V I/O make it well-suited for industrial PLC modules and motor-control inverter boards.
When designing with this part, place 100 nF decoupling capacitors as close as possible to every VDD/VSS pair and ensure the MCLR reset circuit uses the recommended RC network. The 'I' suffix indicates the industrial -40 C to +85 C operating range and the 'A' denotes Flash revision 2 silicon; this 'T' tape-and-reel variant is the surface-mount packaging form of the original -30I/PF die.
This page synthesizes distributor pricing, verified drop-in options, and practical design notes drawn from Microchip application notes - information not consolidated in the manufacturer datasheet alone.
جێگرەوەکانی جێگۆڕکێ بۆ DSPIC30F6013AT-30I/PF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DSPIC30F6013AT-30I/PF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, ADC, Core Architecture, I/O Pins, MSL Level.
DSPIC30F6013A-30I/PF
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DSPIC30F6013AT-30I/PT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DSPIC30F6013A-30I/PT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DSPIC30F6013AT-20E/PF
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DSPIC30F6013AT-20E/PT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DSPIC30F6012AT-30I/PF
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DSPIC30F6013AT-30I/PF زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Core Architecture | dsPIC30F (16-bit modified Harvard DSC) |
| CPU Speed | 30 MIPS at 30 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 132 KB (44K x 24) |
| Supply Voltage Range | 4.5 V to 5.5 V |
| I/O Pins | 60 |
| ADC | 12-bit, up to 16 channels |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | 1 |
| CAN Modules | 2 |
| Timer/Counters | 5 x 16-bit |
| PWM Channels | 8 (Motor Control PWM) |
| پاکێج | 80-TQFP (14x14 mm), Trays |
| پلەی گەرمیی کارکردن | -40 C to +85 C (Industrial) |
| جۆری دامەزراندن | Surface Mount |
| ئاستی MSL | 3 (168 hours) |
| دۆخی RoHS | Compliant |
ڕێکخستنی پینی DSPIC30F6013AT-30I/PF
| پین 1 | EMUD/AN0 — Emulation/Data I/O; analog input 0 |
| پین 2 | EMUC/AN1 — Emulation/Clock; analog input 1 |
| پین 3 | AN2 — Analog input 2 |
| پین 4 | AN3 — Analog input 3 |
| پین 5 | AN4 — Analog input 4 |
| پین 6 | AVDD — Analog supply voltage |
| پین 7 | AVSS — Analog ground |
| پین 8 | AN5 — Analog input 5 |
| پین 9 | AN6 — Analog input 6 |
| پین 10 | AN7 — Analog input 7 |
| پین 11 | AN8 — Analog input 8 |
| پین 12 | AN9 — Analog input 9 |
| پین 13 | AN10 — Analog input 10 |
| پین 14 | AN11 — Analog input 11 |
| پین 15 | AN12 — Analog input 12 |
| پین 16 | AN13 — Analog input 13 |
| پین 17 | AN14 — Analog input 14 |
| پین 18 | AN15 — Analog input 15 |
| پین 19 | AVDD — Analog supply voltage |
| پین 20 | AVSS — Analog ground |
| پین 21 | VDD — Digital supply voltage |
| پین 22 | VSS — Digital ground |
| پین 23 | OSC1/CLKI — Crystal oscillator input / external clock |
| پین 24 | OSC2/CLKO — Crystal oscillator output |
| پین 25 | MCLR — Master Clear reset input |
| پین 26 | PGED2/RB0 — Programming/Data 2; I/O port B0 |
| پین 27 | PGEC2/RB1 — Programming/Clock 2; I/O port B1 |
| پین 28 | RB2 — I/O port B2 |
| پین 29 | RB3 — I/O port B3 |
| پین 30 | RB4 — I/O port B4 |
| پین 31 | RB5 — I/O port B5 |
| پین 32 | RB7 — I/O port B7 |
| پین 33 | RB8 — I/O port B8 |
| پین 34 | RB9 — I/O port B9 |
| پین 35 | RB10 — I/O port B10 |
| پین 36 | RB11 — I/O port B11 |
| پین 37 | RB12 — I/O port B12 |
| پین 38 | RB13 — I/O port B13 |
| پین 39 | RB14 — I/O port B14 |
| پین 40 | RB15 — I/O port B15 |
| پین 41 | VSS — Digital ground |
| پین 42 | VDD — Digital supply voltage |
| پین 43 | RC1 — I/O port C1 |
| پین 44 | RC2 — I/O port C2 |
| پین 45 | RC3 — I/O port C3 |
| پین 46 | RC4 — I/O port C4 |
| پین 47 | RD0 — I/O port D0 |
| پین 48 | RD1 — I/O port D1 |
| پین 49 | RD2 — I/O port D2 |
| پین 50 | RD3 — I/O port D3 |
| پین 51 | RD4 — I/O port D4 |
| پین 52 | RD5 — I/O port D5 |
| پین 53 | RD6 — I/O port D6 |
| پین 54 | RD7 — I/O port D7 |
| پین 55 | RD8 — I/O port D8 |
| پین 56 | RD9 — I/O port D9 |
| پین 57 | RD10 — I/O port D10 |
| پین 58 | RD11 — I/O port D11 |
| پین 59 | RD12 — I/O port D12 |
| پین 60 | RD13 — I/O port D13 |
| پین 61 | RD14 — I/O port D14 |
| پین 62 | RD15 — I/O port D15 |
| پین 63 | RE0 — I/O port E0 |
| پین 64 | RE1 — I/O port E1 |
| پین 65 | RE2 — I/O port E2 |
| پین 66 | RE3 — I/O port E3 |
| پین 67 | RE4 — I/O port E4 |
| پین 68 | RE5 — I/O port E5 |
| پین 69 | RE6 — I/O port E6 |
| پین 70 | RE7 — I/O port E7 |
| پین 71 | RF0 — I/O port F0 |
| پین 72 | RF1 — I/O port F1 |
| پین 73 | RF2 — I/O port F2 |
| پین 74 | RF3 — I/O port F3 |
| پین 75 | RF4 — I/O port F4 |
| پین 76 | RF5 — I/O port F5 |
| پین 77 | RF6 — I/O port F6 |
| پین 78 | VDD — Digital supply voltage |
| پین 79 | VSS — Digital ground |
| پین 80 | RF7 — I/O port F7 |
بەکارهێنانە باوەکان
DSPIC30F6013AT-30I/PF گونجاوە بۆ 6 بەکارھێنانs: Sensorless BLDC / PMSM Motor Control, Automotive Sensor Fusion & CAN Gateway, Industrial UPS and Inverter Control, High-Performance Audio Codec with DSP Effects, Industrial PLC and Process Control Modules, Power Conversion and SMPS Digital Control.
Sensorless BLDC / PMSM Motor Control
The DSPIC30F6013AT-30I/PF drives sensorless BLDC and PMSM motors using its 30 MIPS DSP engine for sliding-mode observer and Field-Oriented Control (FOC) loops. Its eight PWM channels with complementary outputs and dead-band generators eliminate the need for an external gate-driver sequencer. The 12-bit ADC samples phase currents at the PWM reload rate, enabling closed-loop torque bandwidth above 5 kHz. Two CAN 2.0B modules stream motor telemetry to the vehicle or inverter board controller, while the 132 KB Flash holds a full FOC and startup algorithm.
پێشنیارکراو
Automotive Sensor Fusion & CAN Gateway
The DSPIC30F6013AT-30I/PF is well suited for automotive body and powertrain sensor-fusion applications thanks to its dual CAN 2.0B interfaces and 60 5 V-tolerant I/O pins. Two independent CAN channels support gateway bridging between CAN buses at 500 kbps, while the 12-bit ADC digitizes analog sensors (temperature, pressure, position) at up to 200 ksps. The 132 KB Flash and 30 MIPS throughput allow Kalman filter routines and diagnostics (UDS over CAN). Industrial -40 C to +85 C operation plus 5 V I/O simplify integration into 12 V vehicle subsystems without level shifters.
پێشنیارکراو
Industrial UPS and Inverter Control
Industrial UPS and solar inverter designs benefit from the DSPIC30F6013AT-30I/PF's deterministic 5-cycle interrupt response and DSP throughput. The 30 MIPS core computes sinusoidal PWM at 20 kHz carrier frequency with <1% THD on the output, while the eight PWM channels drive a full H-bridge plus auxiliary supplies. The dual CAN and two UART channels stream status to a supervisory PLC; the 132 KB Flash holds multiple control modes (MPPT, grid-tie, battery charging). The 80-TQFP 14x14 mm package and 5 V I/O enable direct drive of gate-driver optocouplers.
پێشنیارکراو
High-Performance Audio Codec with DSP Effects
Pro-audio effects processors and high-end automotive head-unit audio chains benefit from the DSPIC30F6013AT-30I/PF's 30 MIPS core and single-cycle 16-bit MAC engine. Biquad and FIR filter chains for parametric EQ, dynamic range compression, and speaker compensation run in real time at 48 kHz sample rate. The two UART/SPI/I2C channels interface to Bluetooth audio modules and DACs, while two CAN channels stream volume/status to the head unit. The 132 KB Flash stores multiple preset curves for automotive and consumer audio applications.
پێشنیارکراو
Industrial PLC and Process Control Modules
Industrial PLC analog input modules and PID process control blocks benefit from the DSPIC30F6013AT-30I/PF's 5 V-tolerant I/O, 12-bit ADC, and DSP throughput for advanced control algorithms. PID with auto-tuning, Smith predictors, and feed-forward loops run at sub-millisecond update rates on the 30 MIPS core. Two UART channels interface to RS-485 transceivers for Modbus RTU, while CAN connects to the backplane. The wide 4.5 V to 5.5 V supply and industrial temperature grade suit harsh factory-floor environments.
پێشنیارکراو
Power Conversion and SMPS Digital Control
Digitally controlled SMPS and PFC stages benefit from the DSPIC30F6013AT-30I/PF's high-resolution PWM and DSP loop bandwidth. The DSP engine executes digital PFC, average-current-mode control, and adaptive dead-time compensation at 100 kHz switching frequency with sub-microsecond latency. The 12-bit ADC samples at 200 ksps to support both voltage and current-mode control in the same MCU. The 132 KB Flash holds multiple compensation coefficient tables for various load profiles, while the 5 V I/O directly drives digital isolators.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DSPIC30F6013AT-30I/PF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DSPIC30F6013A-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6013AT-20E/PF | DSPIC30F6013AT-20E/PT | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same |
| Core / MIPS | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 30 MIPS at 30 MHz |
| Program Flash | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB (reduced peripherals) |
| CAN Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| I/O Pins | 60 | 60 | 60 | 60 | 60 | 60 | 60 |
جیاکەرەوە سەرەکییەکان
- Dual CAN 2.0B interfaces with independent filters (بەراورد بەDSPIC30F6012AT-30I/PF)
- 30 MIPS performance at 30 MHz (بەراورد بەDSPIC30F6013AT-20E/PF)
- 5 V-tolerant digital I/O on 60 pins (بەراورد بەTypical Cortex-M4 MCU)
تێبینییەکانی دیزاین
Place 100 nF ceramic decoupling capacitors on every AVDD/AVSS and VDD/VSS pair, located within 5 mm of each pin pair. Add a 10 uF bulk tantalum or ceramic capacitor at the device's main VDD entry. The dsPIC30F6013A's analog and digital supplies should be tied to a common 5 V rail but routed with separate traces; a ferrite bead between AVDD and VDD reduces ADC switching noise coupling.
Do not leave the MCLR pin floating; an external 10 kohm pull-up to VDD and a 100 nF to ground is the recommended Microchip reference circuit. Without the pull-up, the device may fail to start or experience spurious resets in noisy motor-control environments. Avoid using the EMUD/EMUC pins as GPIO in production - they are reserved for in-circuit debugging and may interfere with programming tools.
Estimated: at full 30 MIPS operation with all peripherals active and typical 5 V I/O switching, the DSPIC30F6013AT-30I/PF draws approximately 80 mA (0.4 W). On the 80-TQFP package with theta_JA of approximately 50 C/W, the junction rises about 20 C above ambient at 25 C, well within the +85 C industrial limit. For sealed enclosures without airflow, de-rate by 30% or upgrade to the -30I/PT package on a 2 oz copper pour.
Route the crystal traces (OSC1/OSC2) as short as possible with the load capacitors placed within 5 mm of the IC and a ground guard ring around the oscillator cell. Keep ADC analog input traces away from PWM and digital switching lines; cross at right angles if needed. Place the CAN bus termination resistors (120 ohm) within 5 mm of the CANH/CANL pins to minimize stub length and ringing.
زانیاری پابەندبوون
RoHS compliant per Microchip product page. 'PF' suffix denotes lead-free plastic TQFP package. Not AEC-Q100 qualified - this is an industrial-grade part. AEC-Q100 would require the 'EP' or similar automotive suffix.