DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip
MPN: DSPIC30F6013AT-30I/PF ✓ פעילDSPIC30F6013AT-30I/PF סקירה
A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a traditional MCU control core with a single-cycle DSP MAC engine on a single die. In the device taxonomy, this places the DSPIC30F6013AT-30I/PF in the hierarchy: DSC -> DSP/MCU hybrid -> 16-bit microcontroller -> embedded MCU. This category is purpose-built for real-time closed-loop control and high-bandwidth signal processing, where general-purpose MCUs lack DSP throughput and stand-alone DSPs lack peripheral integration.
Key features include 30 MIPS performance from a 30 MHz oscillator, a 12-bit ADC with up to 16 channels, two UART/SPI/I2C modules, two CAN modules, and two 16-bit timer/counters. The device also provides 60 digital I/O lines, PWM modules with dedicated time bases, and an on-chip Flash self-programming bootloader. The wide 4.5 V to 5.5 V supply range simplifies integration into 5 V analog signal chains.
The DSP engine provides a single-cycle 16-bit x 16-bit MAC plus a 40-bit accumulator with dual operand fetch-back, enabling efficient FIR/IIR filtering, FFT butterfly computations, and closed-loop control loops. The modified Harvard architecture keeps program and data memory on separate buses, removing fetch bottlenecks that throttle von Neumann MCUs during DSP workloads.
Typical applications include sensor-less BLDC/PMSM motor drives, automotive sensor fusion (with two CAN interfaces), industrial UPS and inverter control, and high-performance audio codecs with parametric equalization. The 80-pin TQFP and 5 V I/O make it well-suited for industrial PLC modules and motor-control inverter boards.
When designing with this part, place 100 nF decoupling capacitors as close as possible to every VDD/VSS pair and ensure the MCLR reset circuit uses the recommended RC network. The 'I' suffix indicates the industrial -40 C to +85 C operating range and the 'A' denotes Flash revision 2 silicon; this 'T' tape-and-reel variant is the surface-mount packaging form of the original -30I/PF die.
This page synthesizes distributor pricing, verified drop-in options, and practical design notes drawn from Microchip application notes - information not consolidated in the manufacturer datasheet alone.
חלופות תחליף ישיר עבור DSPIC30F6013AT-30I/PF — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DSPIC30F6013AT-30I/PF (אותו גורם צורה וטביעת רגל) — שונים ב Package, ADC, Core Architecture, I/O Pins, MSL Level.
DSPIC30F6013A-30I/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-30I/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6013A-30I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-20E/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-20E/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6012AT-30I/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-30I/PF דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | dsPIC30F (16-bit modified Harvard DSC) |
| CPU Speed | 30 MIPS at 30 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 132 KB (44K x 24) |
| Supply Voltage Range | 4.5 V to 5.5 V |
| I/O Pins | 60 |
| ADC | 12-bit, up to 16 channels |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | 1 |
| CAN Modules | 2 |
| Timer/Counters | 5 x 16-bit |
| PWM Channels | 8 (Motor Control PWM) |
| מארז | 80-TQFP (14x14 mm), Trays |
| טמפרטורת פעולה | -40 C to +85 C (Industrial) |
| סוג הרכבה | Surface Mount |
| רמת MSL | 3 (168 hours) |
| סטטוס RoHS | Compliant |
תצורת פינים של DSPIC30F6013AT-30I/PF
| פין 1 | EMUD/AN0 — Emulation/Data I/O; analog input 0 |
| פין 2 | EMUC/AN1 — Emulation/Clock; analog input 1 |
| פין 3 | AN2 — Analog input 2 |
| פין 4 | AN3 — Analog input 3 |
| פין 5 | AN4 — Analog input 4 |
| פין 6 | AVDD — Analog supply voltage |
| פין 7 | AVSS — Analog ground |
| פין 8 | AN5 — Analog input 5 |
| פין 9 | AN6 — Analog input 6 |
| פין 10 | AN7 — Analog input 7 |
| פין 11 | AN8 — Analog input 8 |
| פין 12 | AN9 — Analog input 9 |
| פין 13 | AN10 — Analog input 10 |
| פין 14 | AN11 — Analog input 11 |
| פין 15 | AN12 — Analog input 12 |
| פין 16 | AN13 — Analog input 13 |
| פין 17 | AN14 — Analog input 14 |
| פין 18 | AN15 — Analog input 15 |
| פין 19 | AVDD — Analog supply voltage |
| פין 20 | AVSS — Analog ground |
| פין 21 | VDD — Digital supply voltage |
| פין 22 | VSS — Digital ground |
| פין 23 | OSC1/CLKI — Crystal oscillator input / external clock |
| פין 24 | OSC2/CLKO — Crystal oscillator output |
| פין 25 | MCLR — Master Clear reset input |
| פין 26 | PGED2/RB0 — Programming/Data 2; I/O port B0 |
| פין 27 | PGEC2/RB1 — Programming/Clock 2; I/O port B1 |
| פין 28 | RB2 — I/O port B2 |
| פין 29 | RB3 — I/O port B3 |
| פין 30 | RB4 — I/O port B4 |
| פין 31 | RB5 — I/O port B5 |
| פין 32 | RB7 — I/O port B7 |
| פין 33 | RB8 — I/O port B8 |
| פין 34 | RB9 — I/O port B9 |
| פין 35 | RB10 — I/O port B10 |
| פין 36 | RB11 — I/O port B11 |
| פין 37 | RB12 — I/O port B12 |
| פין 38 | RB13 — I/O port B13 |
| פין 39 | RB14 — I/O port B14 |
| פין 40 | RB15 — I/O port B15 |
| פין 41 | VSS — Digital ground |
| פין 42 | VDD — Digital supply voltage |
| פין 43 | RC1 — I/O port C1 |
| פין 44 | RC2 — I/O port C2 |
| פין 45 | RC3 — I/O port C3 |
| פין 46 | RC4 — I/O port C4 |
| פין 47 | RD0 — I/O port D0 |
| פין 48 | RD1 — I/O port D1 |
| פין 49 | RD2 — I/O port D2 |
| פין 50 | RD3 — I/O port D3 |
| פין 51 | RD4 — I/O port D4 |
| פין 52 | RD5 — I/O port D5 |
| פין 53 | RD6 — I/O port D6 |
| פין 54 | RD7 — I/O port D7 |
| פין 55 | RD8 — I/O port D8 |
| פין 56 | RD9 — I/O port D9 |
| פין 57 | RD10 — I/O port D10 |
| פין 58 | RD11 — I/O port D11 |
| פין 59 | RD12 — I/O port D12 |
| פין 60 | RD13 — I/O port D13 |
| פין 61 | RD14 — I/O port D14 |
| פין 62 | RD15 — I/O port D15 |
| פין 63 | RE0 — I/O port E0 |
| פין 64 | RE1 — I/O port E1 |
| פין 65 | RE2 — I/O port E2 |
| פין 66 | RE3 — I/O port E3 |
| פין 67 | RE4 — I/O port E4 |
| פין 68 | RE5 — I/O port E5 |
| פין 69 | RE6 — I/O port E6 |
| פין 70 | RE7 — I/O port E7 |
| פין 71 | RF0 — I/O port F0 |
| פין 72 | RF1 — I/O port F1 |
| פין 73 | RF2 — I/O port F2 |
| פין 74 | RF3 — I/O port F3 |
| פין 75 | RF4 — I/O port F4 |
| פין 76 | RF5 — I/O port F5 |
| פין 77 | RF6 — I/O port F6 |
| פין 78 | VDD — Digital supply voltage |
| פין 79 | VSS — Digital ground |
| פין 80 | RF7 — I/O port F7 |
יישומים טיפוסיים
DSPIC30F6013AT-30I/PF מתאים עבור 6 יישוםs: Sensorless BLDC / PMSM Motor Control, Automotive Sensor Fusion & CAN Gateway, Industrial UPS and Inverter Control, High-Performance Audio Codec with DSP Effects, Industrial PLC and Process Control Modules, Power Conversion and SMPS Digital Control.
Sensorless BLDC / PMSM Motor Control
The DSPIC30F6013AT-30I/PF drives sensorless BLDC and PMSM motors using its 30 MIPS DSP engine for sliding-mode observer and Field-Oriented Control (FOC) loops. Its eight PWM channels with complementary outputs and dead-band generators eliminate the need for an external gate-driver sequencer. The 12-bit ADC samples phase currents at the PWM reload rate, enabling closed-loop torque bandwidth above 5 kHz. Two CAN 2.0B modules stream motor telemetry to the vehicle or inverter board controller, while the 132 KB Flash holds a full FOC and startup algorithm.
מומלץ
Automotive Sensor Fusion & CAN Gateway
The DSPIC30F6013AT-30I/PF is well suited for automotive body and powertrain sensor-fusion applications thanks to its dual CAN 2.0B interfaces and 60 5 V-tolerant I/O pins. Two independent CAN channels support gateway bridging between CAN buses at 500 kbps, while the 12-bit ADC digitizes analog sensors (temperature, pressure, position) at up to 200 ksps. The 132 KB Flash and 30 MIPS throughput allow Kalman filter routines and diagnostics (UDS over CAN). Industrial -40 C to +85 C operation plus 5 V I/O simplify integration into 12 V vehicle subsystems without level shifters.
מומלץ
Industrial UPS and Inverter Control
Industrial UPS and solar inverter designs benefit from the DSPIC30F6013AT-30I/PF's deterministic 5-cycle interrupt response and DSP throughput. The 30 MIPS core computes sinusoidal PWM at 20 kHz carrier frequency with <1% THD on the output, while the eight PWM channels drive a full H-bridge plus auxiliary supplies. The dual CAN and two UART channels stream status to a supervisory PLC; the 132 KB Flash holds multiple control modes (MPPT, grid-tie, battery charging). The 80-TQFP 14x14 mm package and 5 V I/O enable direct drive of gate-driver optocouplers.
מומלץ
High-Performance Audio Codec with DSP Effects
Pro-audio effects processors and high-end automotive head-unit audio chains benefit from the DSPIC30F6013AT-30I/PF's 30 MIPS core and single-cycle 16-bit MAC engine. Biquad and FIR filter chains for parametric EQ, dynamic range compression, and speaker compensation run in real time at 48 kHz sample rate. The two UART/SPI/I2C channels interface to Bluetooth audio modules and DACs, while two CAN channels stream volume/status to the head unit. The 132 KB Flash stores multiple preset curves for automotive and consumer audio applications.
מומלץ
Industrial PLC and Process Control Modules
Industrial PLC analog input modules and PID process control blocks benefit from the DSPIC30F6013AT-30I/PF's 5 V-tolerant I/O, 12-bit ADC, and DSP throughput for advanced control algorithms. PID with auto-tuning, Smith predictors, and feed-forward loops run at sub-millisecond update rates on the 30 MIPS core. Two UART channels interface to RS-485 transceivers for Modbus RTU, while CAN connects to the backplane. The wide 4.5 V to 5.5 V supply and industrial temperature grade suit harsh factory-floor environments.
מומלץ
Power Conversion and SMPS Digital Control
Digitally controlled SMPS and PFC stages benefit from the DSPIC30F6013AT-30I/PF's high-resolution PWM and DSP loop bandwidth. The DSP engine executes digital PFC, average-current-mode control, and adaptive dead-time compensation at 100 kHz switching frequency with sub-microsecond latency. The 12-bit ADC samples at 200 ksps to support both voltage and current-mode control in the same MCU. The 132 KB Flash holds multiple compensation coefficient tables for various load profiles, while the 5 V I/O directly drives digital isolators.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DSPIC30F6013AT-30I/PF — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DSPIC30F6013A-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6013AT-20E/PF | DSPIC30F6013AT-20E/PT | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same |
| Core / MIPS | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 30 MIPS at 30 MHz |
| Program Flash | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB (reduced peripherals) |
| CAN Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| I/O Pins | 60 | 60 | 60 | 60 | 60 | 60 | 60 |
מבדילים עיקריים
- Dual CAN 2.0B interfaces with independent filters (לעומתDSPIC30F6012AT-30I/PF)
- 30 MIPS performance at 30 MHz (לעומתDSPIC30F6013AT-20E/PF)
- 5 V-tolerant digital I/O on 60 pins (לעומתTypical Cortex-M4 MCU)
הערות תכנון
Place 100 nF ceramic decoupling capacitors on every AVDD/AVSS and VDD/VSS pair, located within 5 mm of each pin pair. Add a 10 uF bulk tantalum or ceramic capacitor at the device's main VDD entry. The dsPIC30F6013A's analog and digital supplies should be tied to a common 5 V rail but routed with separate traces; a ferrite bead between AVDD and VDD reduces ADC switching noise coupling.
Do not leave the MCLR pin floating; an external 10 kohm pull-up to VDD and a 100 nF to ground is the recommended Microchip reference circuit. Without the pull-up, the device may fail to start or experience spurious resets in noisy motor-control environments. Avoid using the EMUD/EMUC pins as GPIO in production - they are reserved for in-circuit debugging and may interfere with programming tools.
Estimated: at full 30 MIPS operation with all peripherals active and typical 5 V I/O switching, the DSPIC30F6013AT-30I/PF draws approximately 80 mA (0.4 W). On the 80-TQFP package with theta_JA of approximately 50 C/W, the junction rises about 20 C above ambient at 25 C, well within the +85 C industrial limit. For sealed enclosures without airflow, de-rate by 30% or upgrade to the -30I/PT package on a 2 oz copper pour.
Route the crystal traces (OSC1/OSC2) as short as possible with the load capacitors placed within 5 mm of the IC and a ground guard ring around the oscillator cell. Keep ADC analog input traces away from PWM and digital switching lines; cross at right angles if needed. Place the CAN bus termination resistors (120 ohm) within 5 mm of the CANH/CANL pins to minimize stub length and ringing.
מידע על תאימות
RoHS compliant per Microchip product page. 'PF' suffix denotes lead-free plastic TQFP package. Not AEC-Q100 qualified - this is an industrial-grade part. AEC-Q100 would require the 'EP' or similar automotive suffix.
