DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip
Teilenummer: DSPIC30F6013AT-30I/PF ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $18.95 | $18,95 |
| 10 | $17.2 | $172,00 |
| 100 | $15.1 | $1.510,00 |
| 500 | $13.45 | $6.725,00 |
| 1.000 | $11.85 | $11.850,00 |
DSPIC30F6013AT-30I/PF Übersicht
A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a traditional MCU control core with a single-cycle DSP MAC engine on a single die. In the device taxonomy, this places the DSPIC30F6013AT-30I/PF in the hierarchy: DSC -> DSP/MCU hybrid -> 16-bit microcontroller -> embedded MCU. This category is purpose-built for real-time closed-loop control and high-bandwidth signal processing, where general-purpose MCUs lack DSP throughput and stand-alone DSPs lack peripheral integration.
Key features include 30 MIPS performance from a 30 MHz oscillator, a 12-bit ADC with up to 16 channels, two UART/SPI/I2C modules, two CAN modules, and two 16-bit timer/counters. The device also provides 60 digital I/O lines, PWM modules with dedicated time bases, and an on-chip Flash self-programming bootloader. The wide 4.5 V to 5.5 V supply range simplifies integration into 5 V analog signal chains.
The DSP engine provides a single-cycle 16-bit x 16-bit MAC plus a 40-bit accumulator with dual operand fetch-back, enabling efficient FIR/IIR filtering, FFT butterfly computations, and closed-loop control loops. The modified Harvard architecture keeps program and data memory on separate buses, removing fetch bottlenecks that throttle von Neumann MCUs during DSP workloads.
Typical applications include sensor-less BLDC/PMSM motor drives, automotive sensor fusion (with two CAN interfaces), industrial UPS and inverter control, and high-performance audio codecs with parametric equalization. The 80-pin TQFP and 5 V I/O make it well-suited for industrial PLC modules and motor-control inverter boards.
When designing with this part, place 100 nF decoupling capacitors as close as possible to every VDD/VSS pair and ensure the MCLR reset circuit uses the recommended RC network. The 'I' suffix indicates the industrial -40 C to +85 C operating range and the 'A' denotes Flash revision 2 silicon; this 'T' tape-and-reel variant is the surface-mount packaging form of the original -30I/PF die.
This page synthesizes distributor pricing, verified drop-in options, and practical design notes drawn from Microchip application notes - information not consolidated in the manufacturer datasheet alone.
Drop-in-Alternativen für DSPIC30F6013AT-30I/PF – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC30F6013AT-30I/PF (gleiche Bauform und Footprint) – abweichend in Package, ADC, Core Architecture, I/O Pins, MSL Level.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC30F6013A-30I/PF
✅ Drop-In✓ Auf Lager
$14.2 / Stück
Datenblatt ansehen →DSPIC30F6013AT-30I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC30F6013A-30I/PT
✅ Drop-In✓ Auf Lager
$10.93 / Stück
Datenblatt ansehen →DSPIC30F6013AT-20E/PF
✅ Drop-In✓ Auf Lager
$7.3 / Stück
Datenblatt ansehen →DSPIC30F6013AT-20E/PT
✅ Drop-In✓ Auf Lager
$8.05 / Stück
Datenblatt ansehen →DSPIC30F6012AT-30I/PF
✅ Drop-In✓ Auf Lager
$11.2 / Stück
Datenblatt ansehen →DSPIC30F6013AT-30I/PF Grenzwerte & elektrische Eigenschaften
| Core Architecture | dsPIC30F (16-bit modified Harvard DSC) |
| CPU Speed | 30 MIPS at 30 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 132 KB (44K x 24) |
| Supply Voltage Range | 4.5 V to 5.5 V |
| I/O Pins | 60 |
| ADC | 12-bit, up to 16 channels |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | 1 |
| CAN Modules | 2 |
| Timer/Counters | 5 x 16-bit |
| PWM Channels | 8 (Motor Control PWM) |
| Gehäuse | 80-TQFP (14x14 mm), Trays |
| Betriebstemperatur | -40 C to +85 C (Industrial) |
| Montageart | Surface Mount |
| MSL-Level | 3 (168 hours) |
| RoHS-Status | Compliant |
DSPIC30F6013AT-30I/PF Pin-Konfiguration
| Pin 1 | EMUD/AN0 — Emulation/Data I/O; analog input 0 |
| Pin 2 | EMUC/AN1 — Emulation/Clock; analog input 1 |
| Pin 3 | AN2 — Analog input 2 |
| Pin 4 | AN3 — Analog input 3 |
| Pin 5 | AN4 — Analog input 4 |
| Pin 6 | AVDD — Analog supply voltage |
| Pin 7 | AVSS — Analog ground |
| Pin 8 | AN5 — Analog input 5 |
| Pin 9 | AN6 — Analog input 6 |
| Pin 10 | AN7 — Analog input 7 |
| Pin 11 | AN8 — Analog input 8 |
| Pin 12 | AN9 — Analog input 9 |
| Pin 13 | AN10 — Analog input 10 |
| Pin 14 | AN11 — Analog input 11 |
| Pin 15 | AN12 — Analog input 12 |
| Pin 16 | AN13 — Analog input 13 |
| Pin 17 | AN14 — Analog input 14 |
| Pin 18 | AN15 — Analog input 15 |
| Pin 19 | AVDD — Analog supply voltage |
| Pin 20 | AVSS — Analog ground |
| Pin 21 | VDD — Digital supply voltage |
| Pin 22 | VSS — Digital ground |
| Pin 23 | OSC1/CLKI — Crystal oscillator input / external clock |
| Pin 24 | OSC2/CLKO — Crystal oscillator output |
| Pin 25 | MCLR — Master Clear reset input |
| Pin 26 | PGED2/RB0 — Programming/Data 2; I/O port B0 |
| Pin 27 | PGEC2/RB1 — Programming/Clock 2; I/O port B1 |
| Pin 28 | RB2 — I/O port B2 |
| Pin 29 | RB3 — I/O port B3 |
| Pin 30 | RB4 — I/O port B4 |
| Pin 31 | RB5 — I/O port B5 |
| Pin 32 | RB7 — I/O port B7 |
| Pin 33 | RB8 — I/O port B8 |
| Pin 34 | RB9 — I/O port B9 |
| Pin 35 | RB10 — I/O port B10 |
| Pin 36 | RB11 — I/O port B11 |
| Pin 37 | RB12 — I/O port B12 |
| Pin 38 | RB13 — I/O port B13 |
| Pin 39 | RB14 — I/O port B14 |
| Pin 40 | RB15 — I/O port B15 |
| Pin 41 | VSS — Digital ground |
| Pin 42 | VDD — Digital supply voltage |
| Pin 43 | RC1 — I/O port C1 |
| Pin 44 | RC2 — I/O port C2 |
| Pin 45 | RC3 — I/O port C3 |
| Pin 46 | RC4 — I/O port C4 |
| Pin 47 | RD0 — I/O port D0 |
| Pin 48 | RD1 — I/O port D1 |
| Pin 49 | RD2 — I/O port D2 |
| Pin 50 | RD3 — I/O port D3 |
| Pin 51 | RD4 — I/O port D4 |
| Pin 52 | RD5 — I/O port D5 |
| Pin 53 | RD6 — I/O port D6 |
| Pin 54 | RD7 — I/O port D7 |
| Pin 55 | RD8 — I/O port D8 |
| Pin 56 | RD9 — I/O port D9 |
| Pin 57 | RD10 — I/O port D10 |
| Pin 58 | RD11 — I/O port D11 |
| Pin 59 | RD12 — I/O port D12 |
| Pin 60 | RD13 — I/O port D13 |
| Pin 61 | RD14 — I/O port D14 |
| Pin 62 | RD15 — I/O port D15 |
| Pin 63 | RE0 — I/O port E0 |
| Pin 64 | RE1 — I/O port E1 |
| Pin 65 | RE2 — I/O port E2 |
| Pin 66 | RE3 — I/O port E3 |
| Pin 67 | RE4 — I/O port E4 |
| Pin 68 | RE5 — I/O port E5 |
| Pin 69 | RE6 — I/O port E6 |
| Pin 70 | RE7 — I/O port E7 |
| Pin 71 | RF0 — I/O port F0 |
| Pin 72 | RF1 — I/O port F1 |
| Pin 73 | RF2 — I/O port F2 |
| Pin 74 | RF3 — I/O port F3 |
| Pin 75 | RF4 — I/O port F4 |
| Pin 76 | RF5 — I/O port F5 |
| Pin 77 | RF6 — I/O port F6 |
| Pin 78 | VDD — Digital supply voltage |
| Pin 79 | VSS — Digital ground |
| Pin 80 | RF7 — I/O port F7 |
Typische Anwendungen
DSPIC30F6013AT-30I/PF ist geeignet für 6 Anwendungs: Sensorless BLDC / PMSM Motor Control, Automotive Sensor Fusion & CAN Gateway, Industrial UPS and Inverter Control, High-Performance Audio Codec with DSP Effects, Industrial PLC and Process Control Modules, Power Conversion and SMPS Digital Control.
Sensorless BLDC / PMSM Motor Control
The DSPIC30F6013AT-30I/PF drives sensorless BLDC and PMSM motors using its 30 MIPS DSP engine for sliding-mode observer and Field-Oriented Control (FOC) loops. Its eight PWM channels with complementary outputs and dead-band generators eliminate the need for an external gate-driver sequencer. The 12-bit ADC samples phase currents at the PWM reload rate, enabling closed-loop torque bandwidth above 5 kHz. Two CAN 2.0B modules stream motor telemetry to the vehicle or inverter board controller, while the 132 KB Flash holds a full FOC and startup algorithm.
Empfohlen
Automotive Sensor Fusion & CAN Gateway
The DSPIC30F6013AT-30I/PF is well suited for automotive body and powertrain sensor-fusion applications thanks to its dual CAN 2.0B interfaces and 60 5 V-tolerant I/O pins. Two independent CAN channels support gateway bridging between CAN buses at 500 kbps, while the 12-bit ADC digitizes analog sensors (temperature, pressure, position) at up to 200 ksps. The 132 KB Flash and 30 MIPS throughput allow Kalman filter routines and diagnostics (UDS over CAN). Industrial -40 C to +85 C operation plus 5 V I/O simplify integration into 12 V vehicle subsystems without level shifters.
Empfohlen
Industrial UPS and Inverter Control
Industrial UPS and solar inverter designs benefit from the DSPIC30F6013AT-30I/PF's deterministic 5-cycle interrupt response and DSP throughput. The 30 MIPS core computes sinusoidal PWM at 20 kHz carrier frequency with <1% THD on the output, while the eight PWM channels drive a full H-bridge plus auxiliary supplies. The dual CAN and two UART channels stream status to a supervisory PLC; the 132 KB Flash holds multiple control modes (MPPT, grid-tie, battery charging). The 80-TQFP 14x14 mm package and 5 V I/O enable direct drive of gate-driver optocouplers.
Empfohlen
High-Performance Audio Codec with DSP Effects
Pro-audio effects processors and high-end automotive head-unit audio chains benefit from the DSPIC30F6013AT-30I/PF's 30 MIPS core and single-cycle 16-bit MAC engine. Biquad and FIR filter chains for parametric EQ, dynamic range compression, and speaker compensation run in real time at 48 kHz sample rate. The two UART/SPI/I2C channels interface to Bluetooth audio modules and DACs, while two CAN channels stream volume/status to the head unit. The 132 KB Flash stores multiple preset curves for automotive and consumer audio applications.
Empfohlen
Industrial PLC and Process Control Modules
Industrial PLC analog input modules and PID process control blocks benefit from the DSPIC30F6013AT-30I/PF's 5 V-tolerant I/O, 12-bit ADC, and DSP throughput for advanced control algorithms. PID with auto-tuning, Smith predictors, and feed-forward loops run at sub-millisecond update rates on the 30 MIPS core. Two UART channels interface to RS-485 transceivers for Modbus RTU, while CAN connects to the backplane. The wide 4.5 V to 5.5 V supply and industrial temperature grade suit harsh factory-floor environments.
Empfohlen
Power Conversion and SMPS Digital Control
Digitally controlled SMPS and PFC stages benefit from the DSPIC30F6013AT-30I/PF's high-resolution PWM and DSP loop bandwidth. The DSP engine executes digital PFC, average-current-mode control, and adaptive dead-time compensation at 100 kHz switching frequency with sub-microsecond latency. The 12-bit ADC samples at 200 ksps to support both voltage and current-mode control in the same MCU. The 132 KB Flash holds multiple compensation coefficient tables for various load profiles, while the 5 V I/O directly drives digital isolators.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC30F6013AT-30I/PF – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC30F6013A-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6013AT-20E/PF | DSPIC30F6013AT-20E/PT | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same |
| Core / MIPS | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 30 MIPS at 30 MHz |
| Program Flash | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB (reduced peripherals) |
| CAN Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| I/O Pins | 60 | 60 | 60 | 60 | 60 | 60 | 60 |
Wichtigste Unterscheidungsmerkmale
- Dual CAN 2.0B interfaces with independent filters (vs. DSPIC30F6012AT-30I/PF)
- 30 MIPS performance at 30 MHz (vs. DSPIC30F6013AT-20E/PF)
- 5 V-tolerant digital I/O on 60 pins (vs. Typical Cortex-M4 MCU)
Designhinweise
Place 100 nF ceramic decoupling capacitors on every AVDD/AVSS and VDD/VSS pair, located within 5 mm of each pin pair. Add a 10 uF bulk tantalum or ceramic capacitor at the device's main VDD entry. The dsPIC30F6013A's analog and digital supplies should be tied to a common 5 V rail but routed with separate traces; a ferrite bead between AVDD and VDD reduces ADC switching noise coupling.
Do not leave the MCLR pin floating; an external 10 kohm pull-up to VDD and a 100 nF to ground is the recommended Microchip reference circuit. Without the pull-up, the device may fail to start or experience spurious resets in noisy motor-control environments. Avoid using the EMUD/EMUC pins as GPIO in production - they are reserved for in-circuit debugging and may interfere with programming tools.
Estimated: at full 30 MIPS operation with all peripherals active and typical 5 V I/O switching, the DSPIC30F6013AT-30I/PF draws approximately 80 mA (0.4 W). On the 80-TQFP package with theta_JA of approximately 50 C/W, the junction rises about 20 C above ambient at 25 C, well within the +85 C industrial limit. For sealed enclosures without airflow, de-rate by 30% or upgrade to the -30I/PT package on a 2 oz copper pour.
Route the crystal traces (OSC1/OSC2) as short as possible with the load capacitors placed within 5 mm of the IC and a ground guard ring around the oscillator cell. Keep ADC analog input traces away from PWM and digital switching lines; cross at right angles if needed. Place the CAN bus termination resistors (120 ohm) within 5 mm of the CANH/CANL pins to minimize stub length and ringing.
Compliance-Informationen
RoHS compliant per Microchip product page. 'PF' suffix denotes lead-free plastic TQFP package. Not AEC-Q100 qualified - this is an industrial-grade part. AEC-Q100 would require the 'EP' or similar automotive suffix.
