DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip
부품 번호: DSPIC30F6013AT-30I/PF ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.95 | $18.95 |
| 10 | $17.2 | $172.00 |
| 100 | $15.1 | $1,510.00 |
| 500 | $13.45 | $6,725.00 |
| 1,000 | $11.85 | $11,850.00 |
DSPIC30F6013AT-30I/PF 개요
A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a traditional MCU control core with a single-cycle DSP MAC engine on a single die. In the device taxonomy, this places the DSPIC30F6013AT-30I/PF in the hierarchy: DSC -> DSP/MCU hybrid -> 16-bit microcontroller -> embedded MCU. This category is purpose-built for real-time closed-loop control and high-bandwidth signal processing, where general-purpose MCUs lack DSP throughput and stand-alone DSPs lack peripheral integration.
Key features include 30 MIPS performance from a 30 MHz oscillator, a 12-bit ADC with up to 16 channels, two UART/SPI/I2C modules, two CAN modules, and two 16-bit timer/counters. The device also provides 60 digital I/O lines, PWM modules with dedicated time bases, and an on-chip Flash self-programming bootloader. The wide 4.5 V to 5.5 V supply range simplifies integration into 5 V analog signal chains.
The DSP engine provides a single-cycle 16-bit x 16-bit MAC plus a 40-bit accumulator with dual operand fetch-back, enabling efficient FIR/IIR filtering, FFT butterfly computations, and closed-loop control loops. The modified Harvard architecture keeps program and data memory on separate buses, removing fetch bottlenecks that throttle von Neumann MCUs during DSP workloads.
Typical applications include sensor-less BLDC/PMSM motor drives, automotive sensor fusion (with two CAN interfaces), industrial UPS and inverter control, and high-performance audio codecs with parametric equalization. The 80-pin TQFP and 5 V I/O make it well-suited for industrial PLC modules and motor-control inverter boards.
When designing with this part, place 100 nF decoupling capacitors as close as possible to every VDD/VSS pair and ensure the MCLR reset circuit uses the recommended RC network. The 'I' suffix indicates the industrial -40 C to +85 C operating range and the 'A' denotes Flash revision 2 silicon; this 'T' tape-and-reel variant is the surface-mount packaging form of the original -30I/PF die.
This page synthesizes distributor pricing, verified drop-in options, and practical design notes drawn from Microchip application notes - information not consolidated in the manufacturer datasheet alone.
드롭인 대체품: DSPIC30F6013AT-30I/PF — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DSPIC30F6013AT-30I/PF (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Core Architecture, I/O Pins, MSL Level.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DSPIC30F6013A-30I/PF
✅ 드롭인✓ 재고 있음
$14.2 / 개
데이터시트 보기 →DSPIC30F6013AT-30I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DSPIC30F6013A-30I/PT
✅ 드롭인✓ 재고 있음
$10.93 / 개
데이터시트 보기 →DSPIC30F6013AT-20E/PF
✅ 드롭인✓ 재고 있음
$7.3 / 개
데이터시트 보기 →DSPIC30F6013AT-20E/PT
✅ 드롭인✓ 재고 있음
$8.05 / 개
데이터시트 보기 →DSPIC30F6012AT-30I/PF
✅ 드롭인✓ 재고 있음
$11.2 / 개
데이터시트 보기 →DSPIC30F6013AT-30I/PF 최대 정격 & 전기적 특성
| Core Architecture | dsPIC30F (16-bit modified Harvard DSC) |
| CPU Speed | 30 MIPS at 30 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 132 KB (44K x 24) |
| Supply Voltage Range | 4.5 V to 5.5 V |
| I/O Pins | 60 |
| ADC | 12-bit, up to 16 channels |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | 1 |
| CAN Modules | 2 |
| Timer/Counters | 5 x 16-bit |
| PWM Channels | 8 (Motor Control PWM) |
| 패키지 | 80-TQFP (14x14 mm), Trays |
| 동작 온도 | -40 C to +85 C (Industrial) |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (168 hours) |
| RoHS 상태 | Compliant |
DSPIC30F6013AT-30I/PF 핀 구성
| 핀 1 | EMUD/AN0 — Emulation/Data I/O; analog input 0 |
| 핀 2 | EMUC/AN1 — Emulation/Clock; analog input 1 |
| 핀 3 | AN2 — Analog input 2 |
| 핀 4 | AN3 — Analog input 3 |
| 핀 5 | AN4 — Analog input 4 |
| 핀 6 | AVDD — Analog supply voltage |
| 핀 7 | AVSS — Analog ground |
| 핀 8 | AN5 — Analog input 5 |
| 핀 9 | AN6 — Analog input 6 |
| 핀 10 | AN7 — Analog input 7 |
| 핀 11 | AN8 — Analog input 8 |
| 핀 12 | AN9 — Analog input 9 |
| 핀 13 | AN10 — Analog input 10 |
| 핀 14 | AN11 — Analog input 11 |
| 핀 15 | AN12 — Analog input 12 |
| 핀 16 | AN13 — Analog input 13 |
| 핀 17 | AN14 — Analog input 14 |
| 핀 18 | AN15 — Analog input 15 |
| 핀 19 | AVDD — Analog supply voltage |
| 핀 20 | AVSS — Analog ground |
| 핀 21 | VDD — Digital supply voltage |
| 핀 22 | VSS — Digital ground |
| 핀 23 | OSC1/CLKI — Crystal oscillator input / external clock |
| 핀 24 | OSC2/CLKO — Crystal oscillator output |
| 핀 25 | MCLR — Master Clear reset input |
| 핀 26 | PGED2/RB0 — Programming/Data 2; I/O port B0 |
| 핀 27 | PGEC2/RB1 — Programming/Clock 2; I/O port B1 |
| 핀 28 | RB2 — I/O port B2 |
| 핀 29 | RB3 — I/O port B3 |
| 핀 30 | RB4 — I/O port B4 |
| 핀 31 | RB5 — I/O port B5 |
| 핀 32 | RB7 — I/O port B7 |
| 핀 33 | RB8 — I/O port B8 |
| 핀 34 | RB9 — I/O port B9 |
| 핀 35 | RB10 — I/O port B10 |
| 핀 36 | RB11 — I/O port B11 |
| 핀 37 | RB12 — I/O port B12 |
| 핀 38 | RB13 — I/O port B13 |
| 핀 39 | RB14 — I/O port B14 |
| 핀 40 | RB15 — I/O port B15 |
| 핀 41 | VSS — Digital ground |
| 핀 42 | VDD — Digital supply voltage |
| 핀 43 | RC1 — I/O port C1 |
| 핀 44 | RC2 — I/O port C2 |
| 핀 45 | RC3 — I/O port C3 |
| 핀 46 | RC4 — I/O port C4 |
| 핀 47 | RD0 — I/O port D0 |
| 핀 48 | RD1 — I/O port D1 |
| 핀 49 | RD2 — I/O port D2 |
| 핀 50 | RD3 — I/O port D3 |
| 핀 51 | RD4 — I/O port D4 |
| 핀 52 | RD5 — I/O port D5 |
| 핀 53 | RD6 — I/O port D6 |
| 핀 54 | RD7 — I/O port D7 |
| 핀 55 | RD8 — I/O port D8 |
| 핀 56 | RD9 — I/O port D9 |
| 핀 57 | RD10 — I/O port D10 |
| 핀 58 | RD11 — I/O port D11 |
| 핀 59 | RD12 — I/O port D12 |
| 핀 60 | RD13 — I/O port D13 |
| 핀 61 | RD14 — I/O port D14 |
| 핀 62 | RD15 — I/O port D15 |
| 핀 63 | RE0 — I/O port E0 |
| 핀 64 | RE1 — I/O port E1 |
| 핀 65 | RE2 — I/O port E2 |
| 핀 66 | RE3 — I/O port E3 |
| 핀 67 | RE4 — I/O port E4 |
| 핀 68 | RE5 — I/O port E5 |
| 핀 69 | RE6 — I/O port E6 |
| 핀 70 | RE7 — I/O port E7 |
| 핀 71 | RF0 — I/O port F0 |
| 핀 72 | RF1 — I/O port F1 |
| 핀 73 | RF2 — I/O port F2 |
| 핀 74 | RF3 — I/O port F3 |
| 핀 75 | RF4 — I/O port F4 |
| 핀 76 | RF5 — I/O port F5 |
| 핀 77 | RF6 — I/O port F6 |
| 핀 78 | VDD — Digital supply voltage |
| 핀 79 | VSS — Digital ground |
| 핀 80 | RF7 — I/O port F7 |
일반적인 애플리케이션
DSPIC30F6013AT-30I/PF 적합 용도: 6 애플리케이션s: Sensorless BLDC / PMSM Motor Control, Automotive Sensor Fusion & CAN Gateway, Industrial UPS and Inverter Control, High-Performance Audio Codec with DSP Effects, Industrial PLC and Process Control Modules, Power Conversion and SMPS Digital Control.
Sensorless BLDC / PMSM Motor Control
The DSPIC30F6013AT-30I/PF drives sensorless BLDC and PMSM motors using its 30 MIPS DSP engine for sliding-mode observer and Field-Oriented Control (FOC) loops. Its eight PWM channels with complementary outputs and dead-band generators eliminate the need for an external gate-driver sequencer. The 12-bit ADC samples phase currents at the PWM reload rate, enabling closed-loop torque bandwidth above 5 kHz. Two CAN 2.0B modules stream motor telemetry to the vehicle or inverter board controller, while the 132 KB Flash holds a full FOC and startup algorithm.
추천
Automotive Sensor Fusion & CAN Gateway
The DSPIC30F6013AT-30I/PF is well suited for automotive body and powertrain sensor-fusion applications thanks to its dual CAN 2.0B interfaces and 60 5 V-tolerant I/O pins. Two independent CAN channels support gateway bridging between CAN buses at 500 kbps, while the 12-bit ADC digitizes analog sensors (temperature, pressure, position) at up to 200 ksps. The 132 KB Flash and 30 MIPS throughput allow Kalman filter routines and diagnostics (UDS over CAN). Industrial -40 C to +85 C operation plus 5 V I/O simplify integration into 12 V vehicle subsystems without level shifters.
추천
Industrial UPS and Inverter Control
Industrial UPS and solar inverter designs benefit from the DSPIC30F6013AT-30I/PF's deterministic 5-cycle interrupt response and DSP throughput. The 30 MIPS core computes sinusoidal PWM at 20 kHz carrier frequency with <1% THD on the output, while the eight PWM channels drive a full H-bridge plus auxiliary supplies. The dual CAN and two UART channels stream status to a supervisory PLC; the 132 KB Flash holds multiple control modes (MPPT, grid-tie, battery charging). The 80-TQFP 14x14 mm package and 5 V I/O enable direct drive of gate-driver optocouplers.
추천
High-Performance Audio Codec with DSP Effects
Pro-audio effects processors and high-end automotive head-unit audio chains benefit from the DSPIC30F6013AT-30I/PF's 30 MIPS core and single-cycle 16-bit MAC engine. Biquad and FIR filter chains for parametric EQ, dynamic range compression, and speaker compensation run in real time at 48 kHz sample rate. The two UART/SPI/I2C channels interface to Bluetooth audio modules and DACs, while two CAN channels stream volume/status to the head unit. The 132 KB Flash stores multiple preset curves for automotive and consumer audio applications.
추천
Industrial PLC and Process Control Modules
Industrial PLC analog input modules and PID process control blocks benefit from the DSPIC30F6013AT-30I/PF's 5 V-tolerant I/O, 12-bit ADC, and DSP throughput for advanced control algorithms. PID with auto-tuning, Smith predictors, and feed-forward loops run at sub-millisecond update rates on the 30 MIPS core. Two UART channels interface to RS-485 transceivers for Modbus RTU, while CAN connects to the backplane. The wide 4.5 V to 5.5 V supply and industrial temperature grade suit harsh factory-floor environments.
추천
Power Conversion and SMPS Digital Control
Digitally controlled SMPS and PFC stages benefit from the DSPIC30F6013AT-30I/PF's high-resolution PWM and DSP loop bandwidth. The DSP engine executes digital PFC, average-current-mode control, and adaptive dead-time compensation at 100 kHz switching frequency with sub-microsecond latency. The 12-bit ADC samples at 200 ksps to support both voltage and current-mode control in the same MCU. The 132 KB Flash holds multiple compensation coefficient tables for various load profiles, while the 5 V I/O directly drives digital isolators.
추천
추천 제품 요약
엔지니어링 참조 데이터: DSPIC30F6013AT-30I/PF — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DSPIC30F6013A-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6013AT-20E/PF | DSPIC30F6013AT-20E/PT | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same |
| Core / MIPS | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 30 MIPS at 30 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 20 MIPS at 20 MHz | dsPIC30F / 30 MIPS at 30 MHz |
| Program Flash | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB (reduced peripherals) |
| CAN Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| I/O Pins | 60 | 60 | 60 | 60 | 60 | 60 | 60 |
주요 차별점
- Dual CAN 2.0B interfaces with independent filters (vs DSPIC30F6012AT-30I/PF)
- 30 MIPS performance at 30 MHz (vs DSPIC30F6013AT-20E/PF)
- 5 V-tolerant digital I/O on 60 pins (vs Typical Cortex-M4 MCU)
설계 노트
Place 100 nF ceramic decoupling capacitors on every AVDD/AVSS and VDD/VSS pair, located within 5 mm of each pin pair. Add a 10 uF bulk tantalum or ceramic capacitor at the device's main VDD entry. The dsPIC30F6013A's analog and digital supplies should be tied to a common 5 V rail but routed with separate traces; a ferrite bead between AVDD and VDD reduces ADC switching noise coupling.
Do not leave the MCLR pin floating; an external 10 kohm pull-up to VDD and a 100 nF to ground is the recommended Microchip reference circuit. Without the pull-up, the device may fail to start or experience spurious resets in noisy motor-control environments. Avoid using the EMUD/EMUC pins as GPIO in production - they are reserved for in-circuit debugging and may interfere with programming tools.
Estimated: at full 30 MIPS operation with all peripherals active and typical 5 V I/O switching, the DSPIC30F6013AT-30I/PF draws approximately 80 mA (0.4 W). On the 80-TQFP package with theta_JA of approximately 50 C/W, the junction rises about 20 C above ambient at 25 C, well within the +85 C industrial limit. For sealed enclosures without airflow, de-rate by 30% or upgrade to the -30I/PT package on a 2 oz copper pour.
Route the crystal traces (OSC1/OSC2) as short as possible with the load capacitors placed within 5 mm of the IC and a ground guard ring around the oscillator cell. Keep ADC analog input traces away from PWM and digital switching lines; cross at right angles if needed. Place the CAN bus termination resistors (120 ohm) within 5 mm of the CANH/CANL pins to minimize stub length and ringing.
규정 준수 정보
RoHS compliant per Microchip product page. 'PF' suffix denotes lead-free plastic TQFP package. Not AEC-Q100 qualified - this is an industrial-grade part. AEC-Q100 would require the 'EP' or similar automotive suffix.
