Texas Instruments

INA126UA - 36V Precision MicroPower Instrumentation Amplifier | TI

MPN: INA126UA ✓ چالاک
36 V Vdss 175 µA per channel Id 8-pin SOIC Package
MOQ: 1 |

INA126UA گشتی

The Texas Instruments INA126UA is a single-channel precision instrumentation amplifier with a 36 V maximum supply, 175 µA quiescent current per channel, 250 µV input offset voltage, and an 8-pin SOIC package. It is designed for accurate, low-noise differential-signal acquisition where low power consumption and high common-mode rejection are important.

An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals embedded in larger common-mode voltages. Its internal gain stage rejects common-mode noise and converts the differential difference between two inputs into a single-ended output. The INA126 belongs to the broader hierarchy of instrumentation amplifier, precision amplifier, analog signal-conditioning IC, and semiconductor.

The INA126UA uses a two-op-amp architecture with external gain-setting resistors. Its precision input offset voltage supports accurate bridge, current-sense, and sensor measurements, while the 175 µA per channel quiescent current suits battery-powered and portable equipment. The 250 µV input offset specification is particularly useful when the measured differential signal is small relative to the allowed error.

The device supports supply voltages from 2.7 V to 36 V total, corresponding to the documented operating range of ±1.35 V to ±18 V. Its 200 kHz bandwidth suits relatively slow precision measurements rather than high-speed waveform capture. The two-op-amp topology balances low noise and low quiescent current with a practical gain-setting arrangement using an external resistor.

Typical uses include strain-gauge and RTD signal conditioning, low-side current measurement, bridge excitation, biomedical instrumentation, and portable sensor acquisition. For bridge-based sensors, the instrumentation amplifier rejects ground offsets and common-mode interference before the signal reaches an ADC. For battery-powered systems, the 175 µA per channel current helps limit standby consumption.

Choose the INA126UA when the design requires a precision single-channel amplifier with an 8-pin SOIC footprint and very low quiescent current. Verify the selected gain, output swing, supply voltage, bandwidth, and output-reference arrangement against the manufacturer datasheet. Input and reference pins should be routed away from switching nodes and noisy return currents.

This page combines device specifications, verified drop-in alternatives, application guidance, package details, and selection trade-offs to help engineers evaluate the INA126UA before circuit implementation.

جێگرەوەکانی جێگۆڕکێ بۆ INA126UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA126UA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Architecture, Common-Mode Rejection Ratio, Supply Voltage Range, Quiescent Current.

Texas Instruments
Package: 16-pin SOIC, PDSO16
Common-Mode Rejection Ratio: 100 dB
Supply Voltage Range: 2.7 V to 36 V
Texas Instruments
Package: 8-pin PDIP
Supply Voltage Range: ±1.35 V to ±18 V
Quiescent Current: 175 µA/channel typical
بەراوردکردن لەگەڵ INA126UA →
Texas Instruments
Package: 8-pin SOIC, 3.90 mm width
Architecture: Two-op-amp design
بەراوردکردن لەگەڵ INA126UA →
Texas Instruments
Architecture: Two-op-amp architecture
بەراوردکردن لەگەڵ INA126UA →
Texas Instruments
Package: 8-pin SOIC, 3.90 mm width
Architecture: Three-op-amp instrumentation amplifier with current-feedback input circuitry
Common-Mode Rejection Ratio: 130 dB
بەراوردکردن لەگەڵ INA126UA →
Texas Instruments
Package: 8-pin SOIC (D)
Common-Mode Rejection Ratio: 120 dB minimum
Supply Voltage Range: ±18 V maximum
بەراوردکردن لەگەڵ INA126UA →

INA125U/2K5

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
Instrumentation amplifier with precision voltage reference · 2.7 V to 36 V · -18 V to +18 V (±18 V) · 4 V/V to 10,000 V/V, set by one external resistor · 0.075% · 50 uV · 2 uV/°C · 10 nA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA121UG4

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Provides broader gain selection and higher bandwidth than the INA126UA, requiring gain-network and signal-bandwidth verification

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA128UA

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin SOIC
Precision low-power instrumentation amplifier · 1 channel · 130 dB · 120 dB · 50 uV · 0.5 uV/degC · 5 nA · 700 uA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA129UA

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin SOIC
Precision instrumentation amplifier · 1 circuit · 50 µV maximum · 0.5 µV/°C maximum · 5 nA maximum · 120 dB minimum · ±40 V · ±18 V maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA142UA

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin SOIC
Uses a different gain architecture and lower bandwidth than the 200 kHz INA126UA, so signal bandwidth and feedback values must be recalculated

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA126UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type Single-channel precision instrumentation amplifier
Number of Channels 1 channel
Maximum Supply Voltage 36 V
Minimum Total Supply Voltage 2.7 V
Dual-Supply Operating Range ±1.35 V to ±18 V
ئێستای ئارام 175 µA per channel
Input Offset Voltage 250 µV maximum
Gain Bandwidth 200 kHz
Common-Mode Rejection Ratio 74 dB minimum
Architecture Two-op-amp instrumentation amplifier
Gain Configuration External resistor configuration
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount
Signal Type Differential input, single-ended output
Application Category Low-noise differential signal acquisition
دۆخی RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

ڕێنمایی ڕێکخستنی پینی INA126UA 8-pin soic

ڕێکخستنی پین بۆ INA126UA (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pin soic بۆ INA126UA

هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA126UA.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

INA126UA گونجاوە بۆ 6 بەکارھێنانs: Strain-Gauge Bridge Measurement, Portable Battery-Powered Sensor Interface, Low-Side Current Measurement, Medical and Physiological Instrumentation, RTD Temperature Measurement, Industrial Pressure and Level Sensing.

🏭

Strain-Gauge Bridge Measurement

The INA126UA fits precision strain-gauge bridge measurement because its differential input architecture rejects common-mode voltage while the 250 µV maximum input offset limits signal-chain error. It can amplify the small millivolt-level differential output generated by a resistive bridge without requiring a separate differential ADC front end. The 36 V maximum supply and 200 kHz bandwidth provide adequate range for slow mechanical or load-cell signals. Set the gain with the manufacturer-specified resistor arrangement, verify input and output common-mode limits, and connect the reference pin according to the required output-zero level.

📱

Portable Battery-Powered Sensor Interface

The INA126UA is well suited to portable sensor interfaces because its quiescent current is only 175 µA per channel and its total supply range begins at 2.7 V. These characteristics help conserve energy in battery-operated monitors, environmental sensors, and handheld diagnostic instruments. The 250 µV input offset specification supports small differential sensor outputs, while the two-op-amp architecture provides straightforward gain setup. Power-gating and analog settling should be evaluated at the system level, and the reference and feedback paths should be kept quiet to prevent offset and noise from dominating the measurement.

⚡

Low-Side Current Measurement

The INA126UA can acquire a low-side shunt voltage when the shunt common-mode voltage remains within the amplifier's input range. Its 74 dB minimum common-mode rejection ratio helps reject supply ripple and other common-mode disturbances present in power-system return paths. The 250 µV maximum input offset is important because shunt drops at low current can approach the same scale as the error voltage. Use a Kelvin connection from the shunt terminals, maintain the differential input pair over the PCB, and verify that the gain setting keeps the output within the selected supply's output-swing range.

💊

Medical and Physiological Instrumentation

The INA126UA is appropriate for low-level differential physiological or biomedical signals when the system requires precise offset control, common-mode rejection, and low power consumption. Its 250 µV maximum input offset, 74 dB minimum CMRR, and 175 µA per channel current are useful in compact sensor-conditioning equipment. The 200 kHz bandwidth is suitable for many slow physiological and biochemical signals but not for wideband ECG acquisition. Medical designs must additionally satisfy isolation, leakage-current, safety, and electromagnetic-compatibility requirements at the complete-system level rather than treating the amplifier qualification as a system approval.

🌐

RTD Temperature Measurement

The INA126UA can serve as the low-noise input stage of an RTD measurement circuit when the bridge excitation and output voltage remain within its supply and common-mode limits. The instrumentation-amplifier configuration rejects excitation-signal feedthrough and ground offsets that would otherwise reduce measurement accuracy. Its 250 µV maximum offset supports fine temperature-resolution objectives, and the 36 V maximum supply provides headroom for bridge excitation systems. Select the gain resistor for the RTD and bridge values, account for the amplifier input bias current, and keep the excitation return path separate from sensitive measurement traces.

🔧

Industrial Pressure and Level Sensing

The INA126UA is suitable for precision industrial pressure, level, and position sensors that present differential outputs with substantial common-mode voltage. Its 74 dB minimum CMRR reduces interference from motor drives, switching supplies, and long cable runs, while the 250 µV maximum offset supports low-level sensor accuracy. The 200 kHz bandwidth accommodates most slow process-control signals without requiring a high-speed amplifier. Place input traces as a differential pair, isolate them from switching nodes, and verify surge, isolation, and industrial environmental requirements separately because those protections are not inherent to the 8-pin SOIC amplifier.

Where can I download the INA126UA datasheet PDF?
The official INA126UA datasheet PDF is available from the Texas Instruments product page for the INA126 family. The manufacturer document covers the 2.7 V to 36 V supply range, 175 µA per channel quiescent current, 250 µV input offset voltage, 200 kHz bandwidth, gain configuration, and electrical characteristics. Use the INA126UA ordering information to confirm that the 8-pin SOIC variant matches the PCB footprint and production requirements.
What is the INA126UA and what is its main function?
The INA126UA is a single-channel, two-op-amp precision instrumentation amplifier for accurate, low-noise differential-signal acquisition. According to the Texas Instruments INA126 datasheet, it accepts a total supply voltage from 2.7 V to 36 V, operates at 175 µA per channel, and provides a maximum input offset voltage of 250 µV. It is commonly used to amplify small differential sensor signals while rejecting common-mode voltage and noise.
What are the key specifications of INA126UA that engineers should know?
The INA126UA combines a 36 V maximum supply, 175 µA per channel quiescent current, 250 µV maximum input offset voltage, 200 kHz bandwidth, and 74 dB minimum common-mode rejection ratio in an 8-pin SOIC package. These figures position it as a precision, low-power instrumentation amplifier for bridge sensors, current measurement, portable instruments, and other slow differential-signal acquisition systems.
Where can I find the INA126UA pinout?
The INA126UA pinout is shown in the manufacturer datasheet under the package and pin-configuration information for the 8-pin SOIC option. Assign PCB tracks from that diagram rather than inferring connections from a generic instrumentation-amplifier layout. Pay particular attention to the supply, ground, input, reference, feedback, and gain-setting connections because their positions vary among precision instrumentation-amplifier families.
Is INA126UA suitable for low-power sensor applications?
Yes, INA126UA is suitable for low-power sensor applications because its quiescent current is 175 µA per channel and its supply range permits operation from 2.7 V to 36 V total. The 250 µV maximum input offset and 74 dB minimum common-mode rejection ratio support accurate differential measurements. Its 200 kHz bandwidth is appropriate for relatively slow sensor signals, but it is not the preferred choice for high-bandwidth waveform acquisition.
Where can I buy INA126UA online?
The INA126UA can be requested through the Request a Quote form on this page for current commercial availability, lead time, and order handling. The part is a Texas Instruments 8-pin SOIC instrumentation amplifier. When requesting a quotation, include the INA126UA manufacturer part number, target quantity, acceptable delivery date, and whether reel, tube, or another authorized packing format is required.
What is the price of INA126UA?
Current INA126UA pricing should be obtained through the Request a Quote form on this page so that quantity, packing format, currency, and delivery terms can be matched to the procurement request. The component is the 8-pin SOIC Texas Instruments ordering variant. Avoid comparing quotations for INA126U, INA126PA, or other gain and packing codes because those identifiers can represent different orderable configurations.
What is the lead time for INA126UA?
Request the current INA126UA lead time through the Request a Quote form on this page, including your required quantity and target delivery date. Lead time can change with order volume, production conditions, and packing requirements. The manufacturer part number to submit is INA126UA, which identifies the single-channel 8-pin SOIC configuration.
Is INA126UA in stock?
Use the Request a Quote form on this page to request the current stock position and expected shipment timing for INA126UA. Inventory should be confirmed against the requested quantity and delivery date rather than inferred from a catalog listing. Include any required reel, tube, or other packing details in the request.
What is the difference between INA126UA and INA121UG4?
The INA126UA and INA121UG4 are both precision instrumentation amplifiers in 8-pin SOIC packages, but their gain arrangements and bandwidth differ. The INA126UA is specified at 200 kHz bandwidth and 175 µA per channel, while the INA121UG4 provides additional gain choices and a higher bandwidth. Both should be checked against the required gain, output range, supply arrangement, and exact PCB pin map before substitution.
What is the difference between INA126UA and INA125U/2K5?
The INA126UA and INA125U/2K5 belong to related precision instrumentation-amplifier families and use 8-pin SOIC packages. Their principal distinction is gain implementation: INA126 supports its documented gain choices through external gain-setting arrangements, whereas INA125U/2K5 is associated with the INA125 gain architecture. Verify the actual gain, bandwidth, feedback connections, and package drawing because a common package does not guarantee identical functional behavior.
When should I choose INA126UA over INA121UG4 or INA125U/2K5?
Choose INA126UA when low quiescent current, a 250 µV maximum input offset specification, and the INA126 gain configuration are central to the design. Its 175 µA per channel operating current is well suited to portable measurement systems. Choose INA121UG4 when its broader gain selection or bandwidth is more useful, and choose INA125U/2K5 when the INA125 gain architecture is required, provided the revised gain and bandwidth fit the application.
What is the best drop-in replacement for INA126UA?
No universal drop-in replacement can be selected without the required gain, supply voltage, bandwidth, output range, and exact pin map. INA125U/2K5 and INA121UG4 are relevant 8-pin SOIC candidates identified for comparison, but their gain implementations and bandwidth differ. Use the manufacturer data to confirm pin-to-pin compatibility, and validate input offset, common-mode rejection, output swing, and noise in the intended circuit.
What can replace INA126UA in an 8-pin SOIC design?
The INA125U/2K5 and INA121UG4 can be evaluated as 8-pin SOIC replacements for the INA126UA, but they should not be treated as automatic functional equivalents. Their gain-selection methods and bandwidth differ from the INA126UA, and the feedback network must be redesigned where necessary. Confirm every connection against the relevant manufacturer datasheet and validate the completed circuit over the full input, output, and supply ranges.
Is INA126UA the same as an Analog Devices instrumentation amplifier?
The INA126UA is not identical to an Analog Devices instrumentation amplifier merely because both amplify differential signals. The verified cross-reference information identifies Analog Devices as a replacement manufacturer for the INA126 family, but it does not identify a specific orderable MPN with verified pin compatibility. Select the Analog Devices part only after confirming the 8-pin SOIC footprint, pin map, gain method, supply range, input offset, bandwidth, and output swing.

داتای سەرچاوەی ئەندازیاری بۆ INA126UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the INA126UA for precision, low-power differential measurements when the circuit needs a 36 V maximum supply, 175 µA per channel current, 250 µV maximum input offset, and the INA126 gain configuration. Evaluate INA125U/2K5 when its gain architecture better matches the feedback network and operating bandwidth. Consider INA121UG4 when broader gain selection or higher bandwidth is more important than the INA126UA's power and offset profile. INA128UA and INA129UA are relevant same-brand options with different gain choices and current consumption. No specific cross-brand MPN can be recommended confidently without a verified 8-pin SOIC pin map and matching electrical characteristics. For every candidate, verify supply range, common-mode input range, output swing, gain accuracy, bandwidth, noise, and thermal behavior before releasing a PCB revision.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA125U/2K5 INA121UG4 INA128UA INA129UA INA142UA
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Gain Architecture INA126 two-op-amp external-resistor configuration INA125 gain architecture INA121 gain architecture INA128 gain architecture INA129 gain architecture INA142 gain architecture
Signal Type Differential input, single-ended output Differential input, single-ended output Differential input, single-ended output Differential input, single-ended output Differential input, single-ended output Differential input, single-ended output

جیاکەرەوە سەرەکییەکان

  • Lower quiescent current within the comparison set (بەراورد بەINA128UA)
  • Precision 250 µV offset specification (بەراورد بەINA121UG4)
  • 36 V supply capability for industrial signal ranges (بەراورد بەINA125U/2K5)

تێبینییەکانی دیزاین

Route the two input signals as a closely spaced differential pair and connect directly to the INA126UA input pins. Keep switching-regulator traces, high-current return paths, and digital clocks away from this pair. Use a continuous ground reference beneath the analog section and connect the feedback and reference components close to their associated pins. This layout reduces conversion of common-mode switching noise into differential error before the amplifier's 74 dB CMRR acts on the signal.

Place the supply bypass capacitor immediately across the INA126UA power and ground pins, with the shortest possible ground connection. Add additional bulk capacitance near the source when the amplifier is powered from a long trace or a switching converter. Although the IC consumes only 175 µA per channel, regulator noise can still enter through the supply pins and gain error. Check the amplifier output across the intended frequency range with the actual source impedance and load.

Do not treat a shared SOIC package as proof of functional interchangeability. INA125U/2K5, INA121UG4, INA128UA, INA129UA, and INA142UA use related instrumentation-amplifier architectures but differ in gain selection and performance. Before replacing the INA126UA, compare every numbered pin, gain-setting resistor, output-reference connection, input common-mode range, output swing, bandwidth, and supply requirement. Revalidate the modified circuit at the minimum and maximum operating conditions.

Calculate the effective error from the 250 µV input offset against the smallest differential signal expected from the sensor. If that signal approaches the offset magnitude, consider averaging, higher resolution, calibration, or a lower-offset amplifier family. For bridge or current-shunt measurements, preserve Kelvin connections so voltage-drop in power and ground conductors does not appear as differential input error. The 200 kHz bandwidth must also remain above the intended signal and measurement bandwidth.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified in the cited product information. Confirm current declarations with the manufacturer before using the component in a regulated production design.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ina126ua datasheet INA126UA pinout INA126UA datasheet pdf INA126UA specifications INA126UA 8-pin SOIC INA126UA gain configuration INA126UA drop-in replacement INA126UA equivalent INA126UA cross reference INA126UA vs INA121UG4 Texas Instruments INA126UA INA126UA price INA126UA stock INA126UA bridge sensor amplifier INA126UA current shunt measurement

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA126UA INA126 INA125U/2K5 INA121UG4 INA128UA INA129UA INA142UA precision instrumentation amplifier instrumentation amplifier differential amplifier analog signal-conditioning IC semiconductor two-op-amp architecture input offset voltage common-mode rejection ratio CMRR quiescent current gain bandwidth external gain-setting resistor 8-pin SOIC SOIC package family surface-mount package strain-gauge bridge RTD temperature measurement low-side current measurement portable instrumentation battery-powered sensor interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ