Texas Instruments

INA137PA - ±6dB Audio Differential Receiver | Texas Instruments

MPN: INA137PA ✓ چالاک
±18 V Vdss 2.9 mA maximum Id 8-pin PDIP Package
MOQ: 1 |

INA137PA گشتی

Texas Instruments INA137PA is a single-channel audio differential line receiver based on a high-performance operational amplifier and on-chip precision resistors. It supports fixed gains of 1/2 (-6 dB) and 2 (+6 dB), operates from dual ±18 V supplies, and is packaged in an 8-pin PDIP. The receiver is intended for balanced audio inputs, professional audio equipment, consumer audio systems, and other applications that require rejection of common-mode signals while preserving low distortion.

An audio differential line receiver is a specialized analog amplifier that amplifies the voltage difference between two input terminals while suppressing a voltage common to both inputs. This function belongs to the hierarchy of difference amplifier, instrumentation amplifier, operational amplifier, and signal-conditioning IC. Balanced audio transmission reduces sensitivity to ground-potential differences and conducted interference, making a precision differential receiver an important interface between a source and downstream audio circuitry.

The INA137PA provides low distortion of 0.0005% at 1 kHz, a high slew rate of 14 V/µs, and common-mode rejection of 90 dB. Its quiescent current is specified at no more than 2.9 mA. The operational-amplifier architecture and integrated precision resistors simplify the implementation of a balanced receiver while retaining the wide output swing and strong output-drive characteristics described for the INA137 family.

The input and feedback resistors can be reversed to select either -6 dB or +6 dB gain, according to the manufacturer datasheet. This flexibility allows a designer to attenuate a high-level balanced source or amplify a lower-level source without changing the receiver package. A unity-gain implementation is not provided by the INA137 itself; the manufacturer identifies INA134 and INA2134 for applications requiring 0 dB gain.

Typical uses include receiving balanced professional-audio mixer outputs, converting balanced sources to unbalanced downstream inputs, conditioning stereo channel signals in broadcast equipment, and rejecting ground-offset noise in installation audio. Exact bandwidth, input impedance, output impedance, and temperature limits must be confirmed from the manufacturer documentation for the final operating conditions.

When laying out the circuit, keep the differential input traces short, matched, and away from switching nodes. Place input and output bypassing capacitors close to their associated supply and signal pins, and route output signals away from high-current switching paths. Verify output swing, load capability, and thermal conditions before driving the next stage.

This page organizes the documented INA137PA characteristics into an engineer-oriented selection guide, application guidance, verified pin-compatible alternatives, and practical layout notes. It also distinguishes the fixed -6 dB and +6 dB configurations from unity-gain receiver choices, helping prevent a package-compatible substitution from introducing an unintended gain change.

جێگرەوەکانی جێگۆڕکێ بۆ INA137PA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA137PA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Slew Rate.

Texas Instruments
Package: 14-pin PDIP (N)
Product Type: Dual audio differential line receiver
بەراوردکردن لەگەڵ INA137PA →
Analog Devices
Package: 8-PDIP (PZ), 0.300 in / 7.62 mm
Slew Rate: 10 V/us typical
بەراوردکردن لەگەڵ INA137PA →

INA2137PA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
Dual audio differential line receiver · 2 channels · 0.5 (-6 dB) · 2 (+6 dB) · 14-pin PDIP (N) · Through-hole · 9 V, 12 V, 15 V, 18 V, 24 V, or 28 V · Differential

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA134PA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
Single audio differential line receiver · 1V/V (0dB) · 0.0005% at 1kHz · 14V/µs · 90dB · ±18V · 2.9mA maximum · 0.01% settling time specification; timing value not provided

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SSM2142P

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
SSM2142P is a close audio differential-receiver alternative with the same 8-pin PDIP format, while gain, supply, bandwidth, and pin behavior require comparison with INA137PA.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA137PA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Single audio differential line receiver
Number of Channels 1 channel
Fixed Gain 1/2 (-6 dB) or 2 (+6 dB)
Supply Voltage Range ±18 V
Total Supply Voltage 36 V
Distortion 0.0005% at 1 kHz
Slew Rate 14 V/µs
Common-Mode Rejection Ratio 90 dB
ئێستای ئارام 2.9 mA maximum
Settling Accuracy 0.01%
پاکێج 8-pin PDIP
جۆری دامەزراندن Through-hole
Internal Resistors On-chip precision resistors
Input Signal Type Differential audio signal
ڕێکخستنی دەرچوون Single-ended
Gain Configurations Resistor reversal selects -6 dB or +6 dB

ڕێنمایی ڕێکخستنی پینی INA137PA 8-pin pdip

ڕێکخستنی پین بۆ INA137PA (پاکێجی 8-pin pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pin pdip بۆ INA137PA

هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA137PA.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

INA137PA گونجاوە بۆ 6 بەکارھێنانs: Balanced Audio Line Input, Professional Audio Mixer Interface, Balanced to Unbalanced Audio Conversion, Audio ADC Front End, Audio DAC Output Conditioning, Broadcast and Studio Signal Routing.

🎧

Balanced Audio Line Input

INA137PA is well suited to receiving a balanced source when the interface needs either 6 dB of attenuation or 6 dB of gain. Its differential receiver rejects common-mode voltage while preserving the wanted audio signal, and the on-chip precision resistors simplify the gain network. The -6 dB configuration can accommodate a source whose level is too high for the following stage, while the +6 dB configuration raises a lower-level source. With dual ±18 V capability, distortion of 0.0005% at 1 kHz, and a 14 V/µs slew rate, the part supports high-fidelity audio paths. Verify common-mode range, bandwidth, output swing, and load drive before finalizing the receiver stage.

🎚️

Professional Audio Mixer Interface

INA137PA can form the input stage of a professional audio mixer channel because it is designed for balanced audio signals and offers selectable -6 dB or +6 dB gain. A common-mode rejection ratio of 90 dB helps reject voltage shared by both conductors, while the 0.0005% distortion at 1 kHz supports low-distortion signal handling. The 8-pin PDIP package is appropriate for through-hole mixer and processor boards where the available supply is dual ±18 V. The selected gain should be chosen from the input sensitivity plan, and the circuit should include local supply bypassing and protection suited to externally connected equipment. Check input bias, common-mode limits, and load behavior against the complete manufacturer specifications.

🔊

Balanced to Unbalanced Audio Conversion

INA137PA is appropriate when a balanced professional-audio source must feed a single-ended consumer or processing input. Its differential input architecture reduces the effect of ground-potential differences that can become audible in unbalanced interconnects. Select -6 dB when the balanced source is too large for the destination input, or use +6 dB when the source needs amplification. The receiver's 90 dB common-mode rejection and 14 V/µs slew rate support clean audio conversion, while its precision integrated resistors reduce the number of external gain components. Confirm output swing, DC offset, output impedance, and downstream loading before installation, particularly when driving long cable runs or multiple coupling stages.

📻

Audio ADC Front End

INA137PA can serve as the balanced input-conditioning stage ahead of an audio ADC when the converter interface requires differential signaling at the source and single-ended signaling at the converter. Its -6 dB and +6 dB modes help match common line-level sources to the converter's input range, while 90 dB common-mode rejection reduces disturbance before digitization. The 0.0005% distortion at 1 kHz and 14 V/µs slew rate preserve large-signal audio dynamics. Place the receiver close to the input connector, bypass the dual supplies locally, and confirm that the ADC sampling architecture can accept the receiver's bandwidth and output characteristics. Input filtering must also be designed for the converter's sampling rate.

🔉

Audio DAC Output Conditioning

INA137PA can condition a balanced DAC output when downstream circuitry requires a single-ended signal or a deliberate -6 dB or +6 dB level adjustment. The differential receiver can reject shared noise or offset on the two output conductors before the final analog stage, while its precision resistor network provides repeatable fixed gain. Its 36 V maximum total supply allows dual ±18 V operation, and the 0.0005% distortion at 1 kHz supports high-fidelity playback equipment. Use the +6 dB mode only when the following stage has adequate headroom; the -6 dB mode offers attenuation without changing the external package. Verify DAC output impedance, DC offset, load capacitance, and the required output swing.

📺

Broadcast and Studio Signal Routing

INA137PA is suitable for studio and broadcast signal-routing boards that receive balanced analog audio over cables subject to ground-potential differences. Its differential architecture and 90 dB common-mode rejection help maintain signal integrity across long interconnects, while selectable -6 dB and +6 dB gain supports common broadcast level conventions. The 8-pin PDIP construction is practical for through-hole equipment with dual ±18 V rails, and the 14 V/µs slew rate provides strong dynamic response. Place the receiver near the input connector and separate sensitive audio routing from power converters and relay contacts. Confirm bandwidth, input impedance, output drive, and thermal limits for each studio equipment architecture.

What is INA137PA and what does it do?
INA137PA is a Texas Instruments single-channel audio differential line receiver with selectable gain of 1/2 (-6 dB) or 2 (+6 dB). It uses a high-performance operational amplifier with on-chip precision resistors to amplify the difference between two balanced input signals. The manufacturer datasheet identifies the device for high-performance audio applications and reports distortion of 0.0005% at 1 kHz.
INA137PA datasheet specifications and key electrical ratings
The principal INA137PA ratings include dual ±18 V supplies, a 14 V/µs slew rate, 90 dB common-mode rejection, and maximum quiescent current of 2.9 mA. According to the Texas Instruments datasheet, distortion is 0.0005% at 1 kHz. These figures define its suitability for low-distortion balanced-audio reception, although bandwidth and impedance values should be taken directly from the complete manufacturer specification tables.
How do I configure INA137PA for -6 dB or +6 dB gain?
INA137PA obtains -6 dB gain by using the standard gain-of-1/2 configuration and +6 dB gain by reversing the input and feedback resistors. According to the Texas Instruments datasheet, these two resistor arrangements are shown as the basic differential-receiver configurations. The package remains unchanged between modes, although the output level, common-mode range, and downstream headroom must be checked for each signal path.
Where can I download the INA137PA datasheet PDF?
The official INA137PA datasheet PDF is available from the Texas Instruments document link at https://www.ti.com/lit/ds/symlink/ina137.pdf. The manufacturer product page at https://www.ti.com/product/INA137 provides ordering information, product status, and related support material. Use the manufacturer's pin-description and application diagrams when assigning PCB signals or reproducing the documented gain configurations.
Where can I find the INA137PA pinout?
The INA137PA pin assignments are shown in the Texas Instruments INA137 datasheet, including the 8-pin PDIP outline and associated pin-description table. The device is an 8-pin PDIP, but the web material available for this page does not expose the complete numbered pin list. Before laying out a PCB, assign every connection directly from the pin-description table and verify orientation against the package drawing.
Is INA137PA suitable for balanced professional audio inputs?
INA137PA is suitable for balanced professional audio inputs because it is an audio differential line receiver with 90 dB common-mode rejection and 0.0005% distortion at 1 kHz. Its differential input arrangement suppresses common-mode voltage while preserving the wanted signal. Confirm output swing, load, bandwidth, and operating-temperature requirements against the manufacturer datasheet before using it with a particular mixer, converter, or monitor amplifier.
What can replace INA137PA as a drop-in receiver?
A drop-in replacement for INA137PA must use the same 8-pin PDIP footprint, preserve pin assignments, and provide compatible -6 dB and +6 dB differential-receiver operation. INA137PAG4, SSM2142P, and INA2137PA are the closest documented candidates, but each requires a pin-by-pin comparison of supply, gain configuration, frequency response, and output drive. Do not approve a substitution solely because the package drawings match.
Is INA137PA the same as SSM2142P?
INA137PA and SSM2142P are similar audio differential receivers, but they are not automatically identical. INA137PA provides fixed 1/2 (-6 dB) or 2 (+6 dB) gain and specifies 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, and 90 dB CMRR. Compare the SSM2142P pin assignments, gain structure, supply limits, bandwidth, noise, and output drive before treating it as a replacement.
INA137PA versus INA134PA: which receiver should I choose?
Choose INA137PA when the receiver must provide selectable -6 dB or +6 dB gain, and choose INA134PA when unity gain is required. The manufacturer datasheet specifically identifies INA134 and INA2134 as the choices for 0 dB applications. A unity-gain and a fixed ±6 dB part may share an 8-pin PDIP outline, but the internal resistor and pin configuration must still be checked before PCB reuse.
When should I choose INA137PA instead of a unity-gain receiver?
Choose INA137PA when the balanced source requires attenuation by 6 dB or amplification by 6 dB. Its precision on-chip resistor network avoids an external gain-setting divider and supports two fixed configurations. A unity-gain receiver is preferable when the source level already matches the downstream circuit and signal-path headroom must be preserved. The correct choice should be based on signal level, common-mode range, and required output swing.
Is INA137PA suitable for an audio DAC or ADC interface?
INA137PA can be suitable for a balanced audio interface when the signal level and frequency response match its -6 dB or +6 dB operating modes. Its 90 dB common-mode rejection and 0.0005% distortion at 1 kHz support balanced audio reception, while the 14 V/µs slew rate provides good dynamic response. Verify converter input range, bandwidth, noise, and required common-mode headroom for the actual converter.
How much power does INA137PA consume?
INA137PA has a specified quiescent current of no more than 2.9 mA. With a dual ±18 V supply, the maximum specified quiescent power is approximately 104.4 mW when both supply rails are at 18 V. This is an estimated arithmetic value based on 36 V total supply and 2.9 mA, not a manufacturer power-dissipation rating. Actual dissipation also depends on signal activity and output load.
What layout practices are important for INA137PA?
Keep the two input traces short, closely matched, and isolated from switching-node and high-current return paths. Place input and output bypassing capacitors close to the device and connect the ground return without long loops through the analog signal area. Route the output separately from the differential input to prevent feedback. These practices are especially important because the INA137PA is intended to suppress common-mode noise rather than act as a general-purpose unity-gain buffer.
Where to buy INA137PA online?
Use the Request a Quote form on this page to request current INA137PA availability, order quantities, and commercial terms. The part is identified as an 8-PDIP receiver IC from Texas Instruments, and the manufacturer product page provides the authoritative product status and ordering information. The form gives buyers a direct route for confirming supply and lead time without relying on a stale listing.
What is the price of INA137PA?
Current INA137PA pricing depends on quantity, inventory, and order configuration, so use the Request a Quote form on this page for a current quote. The structured pricing area is intentionally populated only when an exact quantity-break listing is available. This avoids presenting a stale unit price and lets the quote reflect the requested quantity, packaging, and supply conditions.
What is the lead time and stock status for INA137PA?
Use the Request a Quote form on this page to request the current INA137PA stock position, minimum order quantity, and lead time. Texas Instruments identifies the INA137 family on its product page, and a distributor listing describes INA137PA as an 8-PDIP receiver IC, but live inventory changes independently of those pages. Confirm each order against the quotation rather than treating a listing as a guaranteed stock commitment.
What are the key specifications of INA137PA that engineers should know?
INA137PA combines selectable -6 dB and +6 dB gain, dual ±18 V operation, 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, 90 dB CMRR, and no more than 2.9 mA quiescent current. It is a single-channel differential line receiver in an 8-pin PDIP. These are the principal figures for audio gain planning, common-mode rejection, output-drive, and power-budget checks.

داتای سەرچاوەی ئەندازیاری بۆ INA137PA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose INA137PA when a balanced-audio interface needs a repeatable fixed gain of -6 dB or +6 dB, dual ±18 V operation, low distortion, and strong common-mode rejection. Its integrated precision resistors simplify gain implementation, while the 8-pin PDIP is useful for through-hole audio equipment. Choose INA134PA when the signal path specifically requires unity gain rather than level shifting or attenuation. Consider INA2137PA when its electrical ratings and gain configuration meet the target design, but review its pin behavior and specifications before substitution. SSM2142P is a close cross-brand receiver candidate for through-hole audio designs, yet its supply range, gain structure, bandwidth, noise, and pin assignments require direct comparison. In every case, verify output swing, common-mode range, load capability, and the downstream headroom rather than relying on package similarity alone.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA2137PA INA134PA SSM2142P
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Analog Devices
Product Type Single audio differential line receiver Single audio differential line receiver Audio differential line receiver Audio differential receiver

جیاکەرەوە سەرەکییەکان

  • Selectable fixed gain in one differential receiver (بەراورد بەINA134PA)
  • Low distortion for balanced audio reception (بەراورد بەSSM2142P)
  • Integrated precision gain-setting elements (بەراورد بەINA134PA)

تێبینییەکانی دیزاین

Route the two INA137PA input conductors as a closely matched differential pair and keep them short and away from switching nodes, relay contacts, and high-current return paths. Place the input bypass capacitor near the supply pins and use a quiet ground-return path. Because the receiver’s function depends on cancellation of common-mode voltage, unequal input routing or shared impedance with an output path can reduce noise rejection and channel separation.

Do not treat the 8-pin PDIP outline as proof that every INA-family receiver is interchangeable. INA134PA offers unity gain, whereas INA137PA supports -6 dB and +6 dB; INA2137PA and SSM2142P also require confirmation of pin assignments, supply limits, bandwidth, gain configuration, and output drive. Validate the complete circuit, including signal level and common-mode range, before releasing a PCB substitution.

Use stable, adequately decoupled dual supplies for the ±18 V capability and keep analog and return currents separate from switching-node paths. For a basic power-budget estimate, 36 V total supply multiplied by 2.9 mA maximum quiescent current equals approximately 104.4 mW. Actual dissipation rises with signal activity and output load, so use the lower quiescent figure only as an initial estimate and verify the final thermal design.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status appears in the cited product and datasheet search results. AEC-Q100 qualification is treated as not applicable because INA137PA is an audio differential line receiver rather than an automotive-qualified device.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ina137pa datasheet INA137PA specifications INA137PA pinout INA137PA datasheet pdf INA137PA schematic INA137PA equivalent INA137PA replacement INA137PA cross reference INA137PA vs INA134PA INA137PA vs SSM2142P INA137PA footprint INA137PA price INA137PA stock Texas Instruments INA137PA INA137PA 8-PDIP pinout

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA137PA INA2137PA INA134PA SSM2142P audio differential line receiver difference amplifier operational amplifier signal-conditioning IC balanced audio common-mode rejection ratio CMRR slew rate quiescent current fixed gain -6 dB +6 dB on-chip precision resistors 8-pin PDIP DIP-8 through-hole package dual ±18 V supply professional audio semiconductor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ