Texas Instruments

LM224ADRE4 - Quad 32V 1.2MHz Op Amp | Texas Instruments

MPN: LM224ADRE4 ✓ چالاک
3 V Vdss 2 nA Id 14-pin SOIC Package
MOQ: 1 |

LM224ADRE4 گشتی

Texas Instruments LM224ADRE4 is a four-channel, high-gain operational amplifier IC with a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and supply-voltage operation from 3 V to 32 V. The device is packaged in a 14-pin SOIC and supports general-purpose signal conditioning across industrial, instrumentation, sensor, and control applications.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM224 family belongs to the broader hierarchy of amplifier ICs, analog signal-conditioning ICs, and semiconductors. Internally frequency-compensated amplifiers simplify closed-loop design by removing the need for an external dominant-pole capacitor in many conventional gain configurations.

The LM224ADRE4 provides four high-gain amplifiers in one package, allowing a design to use several independent analog channels without allocating separate single or dual amplifier packages. Typical input offset voltage is 2 mV, typical input bias current is 2 nA, and typical supply-current drain is 0.8 mA. Its common-mode input range includes ground, which supports direct sensing of signals near the negative supply rail.

The 1.2 MHz gain-bandwidth product defines the frequency range available for closed-loop amplification and is particularly useful for low- to moderate-frequency signal paths. A 0.5 V/µs slew rate supports accurate output transitions in amplifier networks that process bipolar, sensor, or control signals. Four amplifiers in one 14-pin SOIC can also reduce board area and simplify assembly compared with four separate single-amplifier packages.

Typical uses include temperature and pressure sensor interfaces, low-level signal conditioning, industrial control loops, instrumentation, and general voltage amplification. In sensor applications, the amplifier can convert a small transducer voltage into a larger signal suitable for an ADC or controller. In control systems, the four channels can support conditioning, active filtering, error amplification, and output buffering within one circuit board.

For reliable operation, maintain adequate supply headroom and verify that input and output voltage excursions remain within the common-mode and output limits stated in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance so that oscillation, offset, or saturation does not affect the assembled circuit.

جێگرەوەکانی جێگۆڕکێ بۆ LM224ADRE4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM224ADRE4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Operating Temperature Range, Package.

Texas Instruments
Amplifier Type: General Purpose
Operating Temperature Range: -40C to +85C
Package: SOIC (D), 14 pins
بەراوردکردن لەگەڵ LM224ADRE4 →

LM324BAIDR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-pin SOIC
4 · 3 V to 36 V · 1.2 MHz · 2 mV (max, BA version) · Push-Pull · -40C to +85C · SOIC (D), 14 pins · Surface Mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902B

✅ جێگرەوەی ڕاستەوخۆ
📦 14-pin SOIC
LM2902B supports a 36 V maximum supply, 4 V higher than the listed 32 V maximum for LM224ADRE4; both provide four high-voltage amplifiers

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM224ADRE4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 4 channels
Amplifier Type High gain, internally frequency compensated
Gain-Bandwidth Product 1.2 MHz
Slew Rate 0.5 V/µs
Minimum Supply Voltage 3 V
Maximum Supply Voltage 32 V
Typical Input Offset Voltage 2 mV
Typical Input Bias Current 2 nA
Typical Supply-Current Drain 0.8 mA
Common-Mode Input Range Includes ground
مەودای پلەی گەرمیی کارکردن -25 °C to +85 °C
ژمارەی پینەکان 14 pins
پاکێج 14-pin SOIC
جۆری دامەزراندن Surface mount
دۆخی RoHS Compliant
Supply Voltage Configuration Single or split supply

ڕێنمایی ڕێکخستنی پینی LM224ADRE4 14-pin soic

ڕێکخستنی پین بۆ LM224ADRE4 (پاکێجی 14-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 14-pin soic بۆ LM224ADRE4

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM224ADRE4.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LM224ADRE4 گونجاوە بۆ 6 بەکارھێنانs: Temperature Sensor Signal Conditioning, Industrial Process Control, Pressure Sensor Interface, Instrumentation and Measurement, Data Acquisition Conditioning, Power Supply Feedback and Control Loops.

🌡️

Temperature Sensor Signal Conditioning

The LM224ADRE4 fits low-level temperature-sensor front ends because its 1.2 MHz gain-bandwidth product handles slow sensor signals while its 2 mV typical input offset voltage limits the input-referred error. The common-mode input range includes ground, allowing the amplifier to operate with the signal near the lower rail on a single supply. Use one channel to amplify the sensor output and configure the remaining channels for filtering, reference buffering, or diagnostics. Because a 14-pin SOIC contains four amplifiers, the design can consolidate several analog functions without adding separate amplifier packages.

🏭

Industrial Process Control

The LM224ADRE4 is appropriate for low-frequency industrial process-control loops that require amplification of sensor and error signals. Its 3 V to 32 V supply range supports more operating headroom than many low-voltage precision amplifiers, while 0.8 mA typical supply-current drain helps limit power consumption. The four internal channels can provide sensor conditioning, active filtering, comparator-like error amplification, and actuator-signal buffering. Designers should use the manufacturer pinout, keep feedback loops compact, and confirm output swing at the selected supply voltage and load.

💊

Pressure Sensor Interface

The LM224ADRE4 can condition the millivolt-level output of a resistive or bridge-based pressure sensor. The 2 mV typical input offset voltage is important when the amplified result is intended to preserve small sensor changes, and the 2 nA typical input bias current supports high-impedance sensing networks. Its 1.2 MHz gain-bandwidth product is more than adequate for pressure signals that change slowly compared with audio bandwidth. A practical implementation may dedicate separate channels to sensor amplification, offset correction, filtering, and output buffering.

🔧

Instrumentation and Measurement

The LM224ADRE4 fits general-purpose instrumentation where several low-frequency analog signals must be measured or buffered. Four high-gain amplifiers in one 14-pin SOIC reduce the number of separate analog packages and allow the board to combine input conditioning, gain stages, and active filters. The 0.5 V/µs slew rate supports reasonably clean signal transitions, while the 1.2 MHz gain-bandwidth product covers many audio-band measurement functions. For precision instruments, engineers should evaluate offset and bias errors against the required accuracy and use the manufacturer’s recommended layout for decoupling and feedback routing.

📊

Data Acquisition Conditioning

The LM224ADRE4 can serve as the analog conditioning stage between low-level transducers and an ADC or data-acquisition controller. Its four amplifier channels allow several inputs to be amplified and filtered with a common device architecture, while the 3 V minimum supply supports operation from compact 5 V systems. The 1.2 MHz gain-bandwidth product permits useful bandwidth for many sensor channels, and the common-mode range including ground supports measurements near the supply floor. Input protection, settling time, and simultaneous-channel performance should be checked against the acquisition system’s sampling requirements.

⚡

Power Supply Feedback and Control Loops

The LM224ADRE4 is suitable for power-supply feedback and supervisory control circuitry operating from elevated rails. Its 32 V listed maximum supply supports applications that operate above common 5 V or 12 V analog ranges, and the four channels can implement voltage-error amplification, current-sense amplification, filtering, and buffered control signals. The 0.8 mA typical supply-current drain is useful in space-constrained or power-conscious designs. Compensation components and loop stability must be derived for the actual converter topology rather than copied without review.

کورتەی بەرهەمە پێشنیارکراوەکان

LM224A Same LM224A device family بەکارهێنراوە لە: Temperature Sensor Signal Conditioning, Industrial Process Control, Pressure Sensor Interface, Data Acquisition Conditioning LM224ADR Texas Instruments بەکارهێنراوە لە: Temperature Sensor Signal Conditioning, Industrial Process Control, Instrumentation and Measurement, Power Supply Feedback and Control Loops LM324B Pin-compatible high-voltage amplifier family بەکارهێنراوە لە: Pressure Sensor Interface, Data Acquisition Conditioning LM2902B Pin-compatible quad amplifier family بەکارهێنراوە لە: Instrumentation and Measurement, Power Supply Feedback and Control Loops
What is the operating voltage of LM224ADRE4?
The LM224ADRE4 operates from a 3 V minimum supply to a 32 V maximum supply. According to the Texas Instruments LM224A product page and manufacturer datasheet, the quad operational amplifier is intended for single-supply or split-supply operation. Its 32 V maximum rating makes it suitable for industrial control, instrumentation, and sensor circuits, but the total supply voltage must remain within that limit under every operating condition.
What are the key specifications of LM224ADRE4 that engineers should know?
The LM224ADRE4 combines four high-gain amplifiers in a 14-pin SOIC with a 1.2 MHz gain-bandwidth product and a 0.5 V/µs slew rate. According to the Texas Instruments manufacturer datasheet, typical input offset voltage is 2 mV, typical input bias current is 2 nA, and typical supply-current drain is 0.8 mA. Its common-mode input range includes ground, making it useful for low-level sensor signals referenced to the negative supply.
Where can I download the LM224ADRE4 datasheet PDF?
The LM224ADRE4 datasheet can be obtained from the official Texas Instruments LM224A product page, which links to the device documentation. According to the manufacturer product page, LM224A is a quad, 30 V, 1.2 MHz operational amplifier with 3 mV offset voltage and -25 °C to +85 °C operation. Use the pin-description table and electrical-characteristics tables in that document for final design verification.
Where can I find the LM224ADRE4 pinout and SOIC-14 connection diagram?
The LM224ADRE4 uses a 14-pin SOIC, and its numbered connection diagram is shown in the Texas Instruments manufacturer datasheet. The device contains four high-gain, internally frequency-compensated operational amplifiers. Use the package drawing when assigning amplifier inputs, outputs, supply pins, and ground connections; the connection diagram should also be checked against the selected board footprint before fabrication.
Is LM224ADRE4 suitable for temperature sensor signal conditioning?
Yes, the LM224ADRE4 is suitable for low-frequency temperature sensor signal conditioning. Its 1.2 MHz gain-bandwidth product provides ample closed-loop bandwidth for typical slow sensor signals, while the 2 mV typical input offset voltage is relevant when the sensor output is small. According to the Texas Instruments datasheet, the common-mode input range includes ground, helping support sensors referenced to a single supply.
Can LM224ADRE4 be used with a single 5 V supply?
The LM224ADRE4 can operate from a single 5 V supply because its stated operating range begins at 3 V. The common-mode input range includes ground, allowing the device to process inputs near the lower supply rail. According to the manufacturer datasheet, the output voltage swing and input common-mode limits must still be respected; these operating conditions are especially important when using high gain with signals close to ground.
What is the difference between LM224ADRE4 and LM324B?
The principal documented difference is the supported supply range: the LM224A product page identifies a 30 V device, while the LM324B family is described as operating to 36 V. Both devices contain four high-voltage operational amplifiers, and Texas Instruments identifies LM324B as a drop-in replacement for LM224 versions. According to the manufacturer LM224 product page, LM324B provides a wider supply ceiling but requires qualification of operating conditions and temperature behavior for the finished design.
What is the difference between LM224ADRE4 and LM2902B?
The LM2902B has a documented 36 V maximum supply range, compared with the LM224 family’s 30 V operating class and the LM224ADRE4 listing’s 32 V maximum. Texas Instruments identifies LM2902B as a drop-in replacement for LM224, LM324, and LM2902 versions. According to the manufacturer LM224 product page, LM2902B is the appropriate family to evaluate when the higher supply ceiling is needed and its electrical limits meet the application.
When should I choose LM224ADRE4 over LM324B?
Choose LM224ADRE4 when an existing 14-pin SOIC design requires the established LM224A electrical behavior and an operating supply below the LM324B 36 V ceiling. Choose LM324B when a pin-compatible next-generation option with a wider 36 V supply range is preferred. According to the Texas Instruments manufacturer documentation, both families provide four high-voltage amplifiers, so the final choice should follow the exact datasheet limits, temperature requirements, and qualification needs of the design.
When should I choose LM224ADRE4 over LM2902B?
Choose LM224ADRE4 when the circuit is designed around the LM224A family limits, including a 1.2 MHz gain-bandwidth product and an operating temperature range of -25 °C to +85 °C. Choose LM2902B when its documented 36 V supply ceiling provides useful design margin. According to the Texas Instruments LM224 product page, LM2902B can drop into LM224-family applications, but engineers should still verify channel behavior, offsets, and temperature limits.
What can replace LM224ADRE4?
LM324B and LM2902B are the drop-in replacement families identified for LM224 designs by Texas Instruments. Both contain four high-voltage amplifiers, while LM324B and LM2902B are described as supporting supplies up to 36 V. According to the manufacturer LM224 product page, the LM224A and LM224ADRE4 use a 14-pin SOIC, so the replacement should be ordered in the matching 14-pin SOIC package and checked against the pinout before substitution.
What is the best cross-brand equivalent for LM224ADRE4?
The best cross-brand equivalent is the four-amplifier, 14-pin SOIC device that meets the required 3 V to 32 V supply limits, 1.2 MHz-class bandwidth, 0.5 V/µs slew rate, offset, bias-current, and temperature requirements. Texas Instruments documents a cross-reference route for competitor equivalents, and Analog Devices is identified in the LM224 cross-reference results. Use that route to obtain a manufacturer-confirmed, pin-to-pin device rather than relying only on generic functional similarity.
Is LM224ADRE4 the same as LM224ADR?
LM224ADRE4 and LM224ADR identify closely related orderable versions of the LM224A quad operational amplifier in a 14-pin SOIC. The distinction is primarily in the exact order suffix and associated reel or packaging format, rather than a change to the four-amplifier device function. For a new assembly, use the full ordering code and verify its quantity, temperature grade, and shipping format against the manufacturer ordering information.
Where to buy LM224ADRE4 online?
Use the Request a Quote form on this page to request LM224ADRE4 availability, current lead time, and order confirmation. The manufacturer product page identifies the device as a Texas Instruments LM224A-family quad operational amplifier, and the target order code uses a 14-pin SOIC. Submit the exact MPN when requesting a quotation so that the commercial response is tied to the correct package and reel configuration.
What is the price of LM224ADRE4?
Request the current LM224ADRE4 quotation through the Request a Quote form on this page. The quote form allows the order quantity and exact suffix to be reviewed before commercial terms are confirmed. This approach also lets the requester identify required production quantities, reel format, and delivery expectations without relying on a stale marketplace listing or a price that may no longer reflect current inventory.
What is the lead time for LM224ADRE4 and is it in stock?
Request the current LM224ADRE4 lead time and inventory confirmation through the Request a Quote form on this page. Stock status can vary by order quantity, packaging format, and manufacturing conditions, so the exact MPN should be included in the request. Texas Instruments identifies the LM224A as a general-purpose quad operational amplifier for industrial and instrumentation applications, but a current delivery commitment should be obtained for the proposed order.
Does LM224ADRE4 require decoupling capacitors?
Yes, the LM224ADRE4 should be supplied with local power bypassing to reduce supply noise and prevent unintended oscillation. Place the recommended ceramic decoupling capacitor close to the supply and ground pins, following the exact layout and capacitor guidance in the Texas Instruments manufacturer datasheet. Keep the input, feedback, and output traces short, and verify stability for the selected gain and feedback network before releasing the PCB design.

داتای سەرچاوەی ئەندازیاری بۆ LM224ADRE4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM224ADRE4 for new and existing 14-pin SOIC designs that use the LM224A four-amplifier family and operate below 32 V. It provides four high-gain, internally compensated channels, a 1.2 MHz gain-bandwidth product, a 0.5 V/µs slew rate, and a common-mode input range that includes ground. Choose LM324B when the same four-amplifier footprint is desired with a documented 36 V supply ceiling, or when next-generation LM324B behavior is preferred. Choose LM2902B when the additional 4 V of listed supply headroom is useful and its electrical limits meet the application. For either replacement, verify the exact order suffix, temperature grade, input limits, output swing, and stability in the manufacturer datasheet before releasing production artwork.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM324B LM2902B
Brand Texas Instruments Texas Instruments Texas Instruments
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC
Number of Amplifiers 4 channels 4 channels 4 channels
Maximum Supply Voltage 32 V 36 V 36 V

جیاکەرەوە سەرەکییەکان

  • Four independent amplifiers consolidated into one 14-pin SOIC (بەراورد بەLM324B)
  • Targeted alternative with a lower supply ceiling (بەراورد بەLM2902B)
  • Single-package integration for multichannel analog conditioning (بەراورد بەLM324B)

تێبینییەکانی دیزاین

Place the manufacturer-recommended supply-bypass capacitor directly between the supply and ground pins of the SOIC. Keep the capacitor and device ground connection short to reduce parasitic inductance, which can improve transient response and help prevent oscillation. Route sensitive input and feedback traces away from the supply-capacitor return current. The 14-pin SOIC footprint should also leave adequate clearance for the lead-forming and soldering process used by the assembly house.

Do not assume that the input common-mode range extends across the entire supply rail merely because the range includes ground. The manufacturer datasheet contains the exact input common-mode and output-swing limits, and the output must also remain within its linear operating region. Gain and feedback values should be checked for stability, especially at higher closed-loop gains where the 1.2 MHz gain-bandwidth product limits usable bandwidth.

Keep each amplifier’s input, feedback, and output loop physically compact to minimize parasitic capacitance and susceptibility to EMI. Grounding should follow the datasheet’s recommended single-point or quiet-ground strategy rather than separating analog and power returns excessively. For four-channel designs, avoid routing high-current or switching-node copper beneath the SOIC, and place input-referenced components close to their associated amplifier pins to minimize board-level noise pickup.

Check every rail and signal excursion against the 3 V to 32 V operating range, including transients caused by inductive loads or switching-supply overshoot. The LM224ADRE4’s typical supply-current drain is 0.8 mA, but total channel and load currents still contribute to device power dissipation. Use conservative supply design margins and verify temperature rise in the assembled PCB rather than inferring thermal performance from the low quiescent current alone.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS compliance is identified by the LM224ADRE4 technical listing. Other environmental and material-compliance declarations are not specified on that listing.

داتا پشتڕاستکراوەتەوە لە: 2026-11-20 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM224ADRE4 datasheet LM224ADRE4 pinout LM224ADRE4 datasheet pdf LM224ADRE4 equivalent LM224ADRE4 replacement LM224ADRE4 cross reference LM224ADRE4 vs LM324B LM224ADRE4 price LM224ADRE4 stock Texas Instruments LM224ADRE4 LM224ADRE4 SOIC-14 op amp LM224ADRE4 sensor amplifier

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM224ADRE4 LM224A LM224ADR LM324B LM2902B operational amplifier quad operational amplifier high-gain amplifier analog IC signal conditioning amplifier IC semiconductor 1.2 MHz gain-bandwidth product 0.5 V/µs slew rate 2 mV input offset voltage 2 nA input bias current 0.8 mA supply-current drain 14-pin SOIC SOIC family surface-mount package industrial control temperature sensor pressure sensor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ