LM224ADRE4 - Quad 32V 1.2MHz Op Amp | Texas Instruments
MPN: LM224ADRE4 ✓ 啟用中LM224ADRE4 概覽
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM224 family belongs to the broader hierarchy of amplifier ICs, analog signal-conditioning ICs, and semiconductors. Internally frequency-compensated amplifiers simplify closed-loop design by removing the need for an external dominant-pole capacitor in many conventional gain configurations.
The LM224ADRE4 provides four high-gain amplifiers in one package, allowing a design to use several independent analog channels without allocating separate single or dual amplifier packages. Typical input offset voltage is 2 mV, typical input bias current is 2 nA, and typical supply-current drain is 0.8 mA. Its common-mode input range includes ground, which supports direct sensing of signals near the negative supply rail.
The 1.2 MHz gain-bandwidth product defines the frequency range available for closed-loop amplification and is particularly useful for low- to moderate-frequency signal paths. A 0.5 V/µs slew rate supports accurate output transitions in amplifier networks that process bipolar, sensor, or control signals. Four amplifiers in one 14-pin SOIC can also reduce board area and simplify assembly compared with four separate single-amplifier packages.
Typical uses include temperature and pressure sensor interfaces, low-level signal conditioning, industrial control loops, instrumentation, and general voltage amplification. In sensor applications, the amplifier can convert a small transducer voltage into a larger signal suitable for an ADC or controller. In control systems, the four channels can support conditioning, active filtering, error amplification, and output buffering within one circuit board.
For reliable operation, maintain adequate supply headroom and verify that input and output voltage excursions remain within the common-mode and output limits stated in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance so that oscillation, offset, or saturation does not affect the assembled circuit.
直接替換替代品,適用於 LM224ADRE4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM224ADRE4 (相同外形與佔位) — 差異在於 Amplifier Type, Operating Temperature Range, Package.
LM324BAIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2902B
✅ 直接替換📋 參考替代品(不在目錄中)
LM224ADRE4 最大額定值與電氣特性
| Number of Amplifiers | 4 channels |
| Amplifier Type | High gain, internally frequency compensated |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Minimum Supply Voltage | 3 V |
| Maximum Supply Voltage | 32 V |
| Typical Input Offset Voltage | 2 mV |
| Typical Input Bias Current | 2 nA |
| Typical Supply-Current Drain | 0.8 mA |
| Common-Mode Input Range | Includes ground |
| 工作溫度範圍 | -25 °C to +85 °C |
| 腳位數 | 14 pins |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
| Supply Voltage Configuration | Single or split supply |
LM224ADRE4 14-pin soic 腳位配置指南
LM224ADRE4(14-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM224ADRE4.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM224ADRE4 適用於 6 應用s: Temperature Sensor Signal Conditioning, Industrial Process Control, Pressure Sensor Interface, Instrumentation and Measurement, Data Acquisition Conditioning, Power Supply Feedback and Control Loops.
Temperature Sensor Signal Conditioning
The LM224ADRE4 fits low-level temperature-sensor front ends because its 1.2 MHz gain-bandwidth product handles slow sensor signals while its 2 mV typical input offset voltage limits the input-referred error. The common-mode input range includes ground, allowing the amplifier to operate with the signal near the lower rail on a single supply. Use one channel to amplify the sensor output and configure the remaining channels for filtering, reference buffering, or diagnostics. Because a 14-pin SOIC contains four amplifiers, the design can consolidate several analog functions without adding separate amplifier packages.
推薦
Industrial Process Control
The LM224ADRE4 is appropriate for low-frequency industrial process-control loops that require amplification of sensor and error signals. Its 3 V to 32 V supply range supports more operating headroom than many low-voltage precision amplifiers, while 0.8 mA typical supply-current drain helps limit power consumption. The four internal channels can provide sensor conditioning, active filtering, comparator-like error amplification, and actuator-signal buffering. Designers should use the manufacturer pinout, keep feedback loops compact, and confirm output swing at the selected supply voltage and load.
推薦
Pressure Sensor Interface
The LM224ADRE4 can condition the millivolt-level output of a resistive or bridge-based pressure sensor. The 2 mV typical input offset voltage is important when the amplified result is intended to preserve small sensor changes, and the 2 nA typical input bias current supports high-impedance sensing networks. Its 1.2 MHz gain-bandwidth product is more than adequate for pressure signals that change slowly compared with audio bandwidth. A practical implementation may dedicate separate channels to sensor amplification, offset correction, filtering, and output buffering.
推薦
Instrumentation and Measurement
The LM224ADRE4 fits general-purpose instrumentation where several low-frequency analog signals must be measured or buffered. Four high-gain amplifiers in one 14-pin SOIC reduce the number of separate analog packages and allow the board to combine input conditioning, gain stages, and active filters. The 0.5 V/µs slew rate supports reasonably clean signal transitions, while the 1.2 MHz gain-bandwidth product covers many audio-band measurement functions. For precision instruments, engineers should evaluate offset and bias errors against the required accuracy and use the manufacturer’s recommended layout for decoupling and feedback routing.
推薦
Data Acquisition Conditioning
The LM224ADRE4 can serve as the analog conditioning stage between low-level transducers and an ADC or data-acquisition controller. Its four amplifier channels allow several inputs to be amplified and filtered with a common device architecture, while the 3 V minimum supply supports operation from compact 5 V systems. The 1.2 MHz gain-bandwidth product permits useful bandwidth for many sensor channels, and the common-mode range including ground supports measurements near the supply floor. Input protection, settling time, and simultaneous-channel performance should be checked against the acquisition system’s sampling requirements.
推薦
Power Supply Feedback and Control Loops
The LM224ADRE4 is suitable for power-supply feedback and supervisory control circuitry operating from elevated rails. Its 32 V listed maximum supply supports applications that operate above common 5 V or 12 V analog ranges, and the four channels can implement voltage-error amplification, current-sense amplification, filtering, and buffered control signals. The 0.8 mA typical supply-current drain is useful in space-constrained or power-conscious designs. Compensation components and loop stability must be derived for the actual converter topology rather than copied without review.
推薦
推薦產品摘要
工程參考資料,適用於 LM224ADRE4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM324B | LM2902B |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 32 V | 36 V | 36 V |
主要差異化特點
- Four independent amplifiers consolidated into one 14-pin SOIC (對比LM324B)
- Targeted alternative with a lower supply ceiling (對比LM2902B)
- Single-package integration for multichannel analog conditioning (對比LM324B)
設計說明
Place the manufacturer-recommended supply-bypass capacitor directly between the supply and ground pins of the SOIC. Keep the capacitor and device ground connection short to reduce parasitic inductance, which can improve transient response and help prevent oscillation. Route sensitive input and feedback traces away from the supply-capacitor return current. The 14-pin SOIC footprint should also leave adequate clearance for the lead-forming and soldering process used by the assembly house.
Do not assume that the input common-mode range extends across the entire supply rail merely because the range includes ground. The manufacturer datasheet contains the exact input common-mode and output-swing limits, and the output must also remain within its linear operating region. Gain and feedback values should be checked for stability, especially at higher closed-loop gains where the 1.2 MHz gain-bandwidth product limits usable bandwidth.
Keep each amplifier’s input, feedback, and output loop physically compact to minimize parasitic capacitance and susceptibility to EMI. Grounding should follow the datasheet’s recommended single-point or quiet-ground strategy rather than separating analog and power returns excessively. For four-channel designs, avoid routing high-current or switching-node copper beneath the SOIC, and place input-referenced components close to their associated amplifier pins to minimize board-level noise pickup.
Check every rail and signal excursion against the 3 V to 32 V operating range, including transients caused by inductive loads or switching-supply overshoot. The LM224ADRE4’s typical supply-current drain is 0.8 mA, but total channel and load currents still contribute to device power dissipation. Use conservative supply design margins and verify temperature rise in the assembled PCB rather than inferring thermal performance from the low quiescent current alone.
合規資訊
RoHS compliance is identified by the LM224ADRE4 technical listing. Other environmental and material-compliance declarations are not specified on that listing.